MC10EP105 D

MC10EP105, MC100EP105
3.3V / 5VECL Quad 2−Input
Differential AND/NAND
Description
The MC10/100EP105 is a quad 2−input differential AND/NAND
gate. Each gate is functionally equivalent to the EP05 and LVEL05
devices. With AC performance much faster than the LVEL05 device,
the EP105 is ideal for applications requiring the fastest AC
performance available.
The 100 Series contains temperature compensation.
http://onsemi.com
MARKING
DIAGRAMS*
Features
MCxxx
EP105
AWLYYWWG
• 275 ps Typical Propagation Delay
• Maximum Frequency > 3 GHz Typical
• PECL Mode Operating Range: VCC = 3.0 V to 5.5 V
LQFP−32
FA SUFFIX
CASE 873A
with VEE = 0 V
• NECL Mode Operating Range: VCC = 0 V
•
•
•
with VEE = −3.0 V to −5.5 V
Open Input Default State
Safety Clamp on Inputs
Pb−Free Packages are Available*
1
1
32
QFN32
MN SUFFIX
CASE 488AM
xxx
A
WL, L
YY, Y
WW, W
G or G
MCxxx
EP105
AWLYYWWG
G
= 10 or 100
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
November, 2006 − Rev. 11
1
Publication Order Number:
MC10EP105/D
MC10EP105, MC100EP105
D0b D1a D1a D1b D1b D2a D2a D2b
D0b D1a D1a D1b D1b D2a D2a D2b
24
23
22
21
20
19
18
24
17
23
22
21
20
19
18
17
D0b
25
16
D2b
D0b
25
16
D2b
D0a
26
15
D3a
D0a
26
15
D3a
D0a
27
14
D3a
D0a
27
14
D3a
VEE
28
13
VCC
VEE
28
13
VCC
Q0
29
12
D3b
Q0
29
12
D3b
Q0
30
11
D3b
Q0
30
11
D3b
VCC
31
10
VEE
VCC
31
10
VEE
VCC
32
9
NC
VCC
32
9
NC
MC10EP105
MC100EP105
1
2
3
4
5
6
7
8
Exposed Pad (EP)
1
2
3
4
5
6
7
8
VCC Q1 Q1 Q2 Q2 Q3 Q3 VCC
VCC Q1
Q1
Q2
Q2
Q3
Q3
VCC
Warning: All VCC and VEE pins must be externally connected
to Power Supply to guarantee proper operation.
Figure 1. 32−Lead LQFP Pinout (Top View)
D0a
Figure 2. 32−Lead QFN Pinout (Top View)
Table 1. PIN DESCRIPTION
Q0
D0a
D0b
D0b
Q0
D1a
Q1
D1a
D1b
D1b
FUNCTION
PIN
Q1
Dna*, Dnb*, Dna*, Dnb*
ECL Data Inputs
Qn, Qn
ECL Data Outputs
VCC
Positive Supply
VEE
Negative Supply
NC
No Connect
* Pins will default LOW when left open.
D2a
Q2
D2a
D2b
D2b
Table 2. TRUTH TABLE
Q2
D3a
Q3
D3a
D3b
D3b
Q3
Dna
Dnb
Dna
L
L
H
H
L
H
L
H
H
H
L
L
VEE
Figure 3. Logic Diagram
http://onsemi.com
2
Dnb
Qn
Qn
H
L
H
L
L
L
L
H
H
H
H
L
MC10EP105, MC100EP105
Table 3. ATTRIBUTES
Characteristics
Value
Internal Input Pulldown Resistor
75 kW
Internal Input Pullup Resistor
N/A
ESD Protection
Human Body Model
Machine Model
Charged Device Model
> 4 kV
> 100 V
> 2 kV
Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1)
LQFP−32
QFN−32
Flammability Rating
Pb Pkg
Pb−Free Pkg
Level 2
−
Level 2
Level 1
Oxygen Index: 28 to 34
UL−94 V−0 @ 0.125 in
Transistor Count
444 Devices
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. For additional information, see Application Note AND8003/D.
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE = 0 V
6
V
VEE
NECL Mode Power Supply
VCC = 0 V
−6
V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
6
−6
V
Iout
Output Current
Continuous
Surge
50
100
mA
IBB
VBB Sink/Source
± 0.5
mA
TA
Operating Temperature Range
−40 to +85
°C
Tstg
Storage Temperature Range
−65 to +150
°C
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
32 LQFP
32 LQFP
80
55
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
32 LQFP
12 to 17
°C/W
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
32 QFN
32 QFN
31
27
°C/W
qJC
Thermal Resistance (Junction−to−Case)
2S2P
32 QFN
12
°C/W
Tsol
Wave Solder
<2 to 3 sec @ 248°C
<2 to 3 sec @ 260°C
265
265
°C
Pb
Pb−Free
VI ≤ VCC
VI ≥ VEE
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
3
MC10EP105, MC100EP105
Table 5. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2)
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
45
58
75
45
59
75
45
60
75
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 3)
2165
2290
2415
2230
2355
2480
2290
2415
2540
mV
VOL
Output LOW Voltage (Note 3)
1365
1490
1615
1430
1555
1680
1490
1615
1740
mV
VIH
Input HIGH Voltage (Single−Ended)
2090
2415
2155
2480
2215
2540
mV
VIL
Input LOW Voltage (Single−Ended)
1365
1690
1460
1755
1490
1815
mV
VIHCMR
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 4)
2.0
3.3
2.0
3.3
2.0
3.3
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
150
0.5
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
3. All loading with 50 W to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
4
MC10EP105, MC100EP105
Table 6. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5)
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
45
58
75
45
59
75
45
60
75
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 6)
3865
3990
4115
3930
4055
4180
3990
4115
4240
mV
VOL
Output LOW Voltage (Note 6)
3065
3190
3315
3130
3255
3380
3190
3315
3440
mV
VIH
Input HIGH Voltage (Single−Ended)
3790
4115
3855
4180
3915
4240
mV
VIL
Input LOW Voltage (Single−Ended)
3065
3390
3130
3455
3190
3515
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 7)
2.0
5.0
2.0
5.0
2.0
5.0
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
150
150
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
6. All loading with 50 W to VCC − 2.0 V.
7. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 7. 10EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 8)
−40°C
Symbol
Characteristic
Min
25°C
Typ
Max
Min
Typ
85°C
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
45
58
75
45
59
75
45
60
75
mA
VOH
Output HIGH Voltage (Note 9)
−1135
−1010
−885
−1070
−945
−820
−1010
−885
−760
mV
VOL
Output LOW Voltage (Note 9)
−1935
−1810
−1685
−1870
−1745
−1620
−1810
−1685
−1560
mV
VIH
Input HIGH Voltage (Single−Ended)
−1210
−885
−1145
−820
−1085
−760
mV
VIL
Input LOW Voltage (Single−Ended)
−1935
−1610
−1870
−1545
−1810
−1485
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 10)
0.0
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
VEE+2.0
0.0
VEE+2.0
150
0.5
0.0
VEE+2.0
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
8. Input and output parameters vary 1:1 with VCC.
9. All loading with 50 W to VCC − 2.0 V.
10. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
5
MC10EP105, MC100EP105
Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 11)
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
45
59
80
45
62
85
45
65
85
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 12)
2155
2280
2405
2155
2280
2405
2155
2280
2405
mV
VOL
Output LOW Voltage (Note 12)
1355
1480
1605
1355
1480
1605
1355
1480
1605
mV
VIH
Input HIGH Voltage (Single−Ended)
2075
2420
2075
2420
2075
2420
mV
VIL
Input LOW Voltage (Single−Ended)
1355
1675
1355
1675
1355
1675
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 13)
2.0
3.3
2.0
3.3
2.0
3.3
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
150
0.5
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
11. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
12. All loading with 50 W to VCC − 2.0 V.
13. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 9. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 14)
−40°C
Symbol
Characteristic
Min
Typ
25°C
Max
Min
Typ
85°C
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
45
63
80
45
66
85
45
69
85
mA
VOH
Output HIGH Voltage (Note 15)
3855
3980
4105
3855
3980
4105
3855
3980
4105
mV
VOL
Output LOW Voltage (Note15)
3055
3180
3305
3055
3180
3305
3055
3180
3305
mV
VIH
Input HIGH Voltage (Single−Ended)
3775
4120
3775
4120
3775
4120
mV
VIL
Input LOW Voltage (Single−Ended)
3055
3375
3055
3375
3055
3375
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 16)
2.0
5.0
2.0
5.0
2.0
5.0
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
150
0.5
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
14. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
15. All loading with 50 W to VCC − 2.0 V.
16. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
6
MC10EP105, MC100EP105
Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 17)
−40°C
Symbol
Characteristic
VCC = −3.3 V
VCC = −5.0 V
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
45
45
59
63
80
80
45
45
62
66
85
85
45
45
65
69
85
85
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 18)
−1145
−1020
−895
−1145
−1020
−895
−1145
−1020
−895
mV
VOL
Output LOW Voltage (Note 18)
−1945
−1820
−1695
−1945
−1820
−1695
−1945
−1820
−1695
mV
VIH
Input HIGH Voltage (Single−Ended)
−1225
−880
−1225
−880
−1225
−880
mV
VIL
Input LOW Voltage (Single−Ended)
−1945
−1625
−1945
−1625
−1945
−1625
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 19)
0.0
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
VEE+2.0
0.0
VEE+2.0
0.0
150
0.5
VEE+2.0
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
17. Input and output parameters vary 1:1 with VCC.
18. All loading with 50 W to VCC − 2.0 V.
19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20)
−40°C
Symbol
Characteristic
fmax
Maximum Frequency
(See Figure 4 Fmax/JITTER)
tPLH,
tPHL
Propagation Delay to
Output Differential
tSKEW
Min
Typ
25°C
Max
Min
>3
175
85°C
Max
Min
>3
250
325
Within Device Skew
Device to Device Skew (Note 21)
10
tJITTER
Cycle−to−Cycle Jitter
(See Figure 4 Fmax/JITTER)
VPP
Input Voltage Swing
(Differential Configuration)
tr
tf
Output Rise/Fall Times
(20% − 80%)
Q
Typ
200
Typ
Max
>3
275
350
50
10
0.2
<1
150
800
1200
100
150
200
225
Unit
GHz
300
375
ps
50
15
50
ps
0.2
<1
0.2
<1
ps
150
800
1200
150
800
1200
mV
120
170
220
150
200
250
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.
21. Skew is measured between outputs under identical transitions.
http://onsemi.com
7
1000
10
900
9
800
8
700
7
600
6
500
5
400
4
300
3
200
100
0
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
2
(JITTER)
0
1000
2000
1
3000
4000
JITTER OUT ps (RMS)
VOUTpp (mV)
MC10EP105, MC100EP105
ÉÉ
ÉÉ
5000
FREQUENCY (MHz)
Figure 4. Fmax/Jitter
Q
Zo = 50 W
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = VCC − 2.0 V
Figure 5. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
http://onsemi.com
8
MC10EP105, MC100EP105
ORDERING INFORMATION
Package
Shipping †
MC10EP105FA
LQFP−32
250 Units / Tray
MC10EP105FAG
LQFP−32
(Pb−Free)
250 Units / Tray
MC10EP105FAR2
LQFP−32
2000 / Tape & Reel
MC10EP105FAR2G
LQFP−32
(Pb−Free)
2000 / Tape & Reel
MC100EP105FA
LQFP−32
250 Units / Tray
MC100EP105FAG
LQFP−32
(Pb−Free)
250 Units / Tray
MC100EP105FAR2
LQFP−32
2000 / Tape & Reel
MC100EP105FAR2G
LQFP−32
(Pb−Free)
2000 / Tape & Reel
Device
MC10EP105MNG
MC100EP105MNG
MC10EP105MNR4G
74 Units / Rail
74 Units / Rail
QFN−32
(Pb−Free)
1000 / Tape & Reel
MC100EP105MNR4G
1000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
http://onsemi.com
9
MC10EP105, MC100EP105
PACKAGE DIMENSIONS
32
A1
A
−T−, −U−, −Z−
32 LEAD LQFP
CASE 873A−02
ISSUE C
4X
25
0.20 (0.008) AB T−U Z
1
AE
−U−
−T−
B
P
V
17
8
BASE
METAL
DETAIL Y
V1
AC T−U Z
AE
DETAIL Y
ÉÉ
ÉÉ
ÉÉ
ÉÉ
9
−Z−
S1
4X
0.20 (0.008) AC T−U Z
F
S
8X M_
D
DETAIL AD
G
−AB−
SECTION AE−AE
C E
−AC−
H
W
K
X
DETAIL AD
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION:
MILLIMETER.
3. DATUM PLANE −AB− IS LOCATED AT
BOTTOM OF LEAD AND IS COINCIDENT
WITH THE LEAD WHERE THE LEAD
EXITS THE PLASTIC BODY AT THE
BOTTOM OF THE PARTING LINE.
4. DATUMS −T−, −U−, AND −Z− TO BE
DETERMINED AT DATUM PLANE −AB−.
5. DIMENSIONS S AND V TO BE
DETERMINED AT SEATING PLANE −AC−.
6. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION. ALLOWABLE
PROTRUSION IS 0.250 (0.010) PER SIDE.
DIMENSIONS A AND B DO INCLUDE
MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE −AB−.
7. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. DAMBAR
PROTRUSION SHALL NOT CAUSE THE
D DIMENSION TO EXCEED 0.520 (0.020).
8. MINIMUM SOLDER PLATE THICKNESS
SHALL BE 0.0076 (0.0003).
9. EXACT SHAPE OF EACH CORNER MAY
VARY FROM DEPICTION.
DIM
A
A1
B
B1
C
D
E
F
G
H
J
K
M
N
P
Q
R
S
S1
V
V1
W
X
http://onsemi.com
10
MILLIMETERS
MIN
MAX
7.000 BSC
3.500 BSC
7.000 BSC
3.500 BSC
1.400
1.600
0.300
0.450
1.350
1.450
0.300
0.400
0.800 BSC
0.050
0.150
0.090
0.200
0.450
0.750
12_ REF
0.090
0.160
0.400 BSC
1_
5_
0.150
0.250
9.000 BSC
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
INCHES
MIN
MAX
0.276 BSC
0.138 BSC
0.276 BSC
0.138 BSC
0.055
0.063
0.012
0.018
0.053
0.057
0.012
0.016
0.031 BSC
0.002
0.006
0.004
0.008
0.018
0.030
12_ REF
0.004
0.006
0.016 BSC
1_
5_
0.006
0.010
0.354 BSC
0.177 BSC
0.354 BSC
0.177 BSC
0.008 REF
0.039 REF
Q_
0.250 (0.010)
0.10 (0.004) AC
GAUGE PLANE
SEATING
PLANE
J
R
M
N
9
0.20 (0.008)
B1
MC10EP105, MC100EP105
PACKAGE DIMENSIONS
QFN32 5*5*1 0.5 P
CASE 488AM−01
ISSUE O
A
B
D
ÉÉ
PIN ONE
LOCATION
2X
0.15 C
2X
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM TERMINAL
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
E
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
TOP VIEW
0.15 C
(A3)
0.10 C
A
32 X
0.08 C
C
L
32 X
9
D2
SEATING
PLANE
A1
SIDE VIEW
MILLIMETERS
MIN
NOM MAX
0.800 0.900 1.000
0.000 0.025 0.050
0.200 REF
0.180 0.250 0.300
5.00 BSC
2.950 3.100 3.250
5.00 BSC
2.950 3.100 3.250
0.500 BSC
0.200
−−−
−−−
0.300 0.400 0.500
EXPOSED PAD
16
SOLDERING FOOTPRINT*
K
32 X
17
5.30
8
3.20
E2
32 X
1
0.63
24
32
25
b
0.10 C A B
32 X
e
3.20
5.30
0.05 C
BOTTOM VIEW
32 X
0.28
28 X
0.50 PITCH
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10EP105/D