NL27WZ14 D

NL27WZ14
Dual Schmitt-Trigger
Inverter
http://onsemi.com
MARKING
DIAGRAMS
6
6
1
M
The NL27WZ14 is a high performance dual inverter with
Schmitt−Trigger inputs operating from a 1.65 to 5.5 V supply.
Pin configuration and function are the same as the NL27WZ04, but
the inputs have hysteresis and, with its Schmitt trigger function, the
NL27WZ14 can be used as a line receiver which will receive slow
input signals. The NL27WZ14 is capable of transforming slowly
changing input signals into sharply defined, jitter−free output signals.
In addition, it has a greater noise margin than conventional inverters.
The NL27WZ14 has hysteresis between the positive−going and the
negative−going input thresholds (typically 1 V) which is determined
internally by transistor ratios and is essentially insensitive to
temperature and supply voltage variations.
SC−88/SOT−363/SC70−6
DF SUFFIX
CASE 419B
MA M G
G
1
Features
• Designed for 1.65 V to 5.5 V VCC Operation
• Over Voltage Tolerant Inputs and Outputs
• LVTTL Compatible − Interface Capability with 5 V TTL Logic
with VCC = 3 V
• LVCMOS Compatible
• 24 mA Balanced Output Sink and Source Capability
• Near Zero Static Supply Current Substantially Reduces System
•
•
•
•
Power Requirements
Current Drive Capability is 24 mA at the Outputs
Chip Complexity: FET = 72
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and are RoHS Compliant
IN A1
1
6
2
GND
IN A2
OUT Y1
5
3
VCC
6
6
1
TSOP−6
DT SUFFIX
CASE 318G
MA
M
G
MA M G
G
1
= Device Marking
= Date Code*
= Pb−Free Package
(Note: Microdot may be in either location)
*Date Code orientation and/or position may vary
depending upon manufacturing location.
PIN ASSIGNMENT
Pin
Function
1
IN A1
2
GND
3
IN A2
4
OUT Y2
5
VCC
6
OUT Y1
OUT Y2
4
FUNCTION TABLE
Figure 1. Pinout (Top View)
IN A1
1
OUT Y1
IN A2
1
OUT Y2
A Input
Y Output
L
H
H
L
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
Figure 2. Logic Symbol
© Semiconductor Components Industries, LLC, 2013
March, 2013 − Rev. 13
1
Publication Order Number:
NL27WZ14/D
NL27WZ14
MAXIMUM RATINGS
Symbol
VCC
Characteristics
DC Supply Voltage
Value
Units
−0.5 to +7.0
V
VI
DC Input Voltage
−0.5 ≤ VI ≤ +7.0
V
VO
DC Output Voltage, Output in Z or LOW State (Note 1)
−0.5 ≤ VO ≤ +7.0
V
IIK
DC Input Diode Current, VI < GND
−50
mA
IOK
DC Output Diode Current, VO < GND
−50
mA
IO
DC Output Sink Current
±50
mA
ICC
DC Supply Current per Supply Pin
±100
mA
IGND
DC Ground Current per Ground Pin
±100
mA
TSTG
Storage Temperature Range
−65 to +150
°C
PD
Power Dissipation in Still Air; SC−88, TSOP−6
200
mW
qJA
Thermal Resistance; SC−88, TSOP−6
333
°C/W
TL
Lead Temperature, 1 mm from case for 10 s
260
°C
TJ
Junction Temperature under Bias
+150
°C
VESD
ESD Withstand Voltage
Human Body Model (Note 2)
Machine Model (Note 3)
Charged Device Model (Note 4)
> 2000
> 200
N/A
ILATCHU
Latchup Performance Above VCC and Below GND at 125°C (Note 5)
V
mA
±100
P
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. IO absolute maximum rating must be observed.
2. Tested to EIA/JESD22−A114−A
3. Tested to EIA/JESD22−A115−A
4. Tested to JESD22−C101−A
5. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
Operating
Data Retention Only
Min
Max
1.65
1.5
5.5
5.5
Units
V
VI
Input Voltage
0
5.5
V
VO
Output Voltage (High or LOW State)
0
5.5
V
TA
Operating Free−Air Temperature
−55
+125
Dt/DV
Input Transition Rise or Fall Rate
VCC = 2.5 V ±0.2 V
VCC =3.0 V ±0.3 V
VCC =5.0 V ±0.5 V
0
0
0
No Limit
No Limit
No Limit
°C
ns/V
ORDERING INFORMATION
Package
Shipping†
NL27WZ14DFT2G
SC−88/SOT−363/SC70−6
(Pb−Free)
3000 / Tape & Reel
NLV27WZ14DFT2G*
SC−88/SOT−363/SC70−6
(Pb−Free)
3000 / Tape & Reel
TSOP−6
(Pb−Free)
3000 / Tape & Reel
Device
NL27WZ14DTT1G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
2
NL27WZ14
DC ELECTRICAL CHARACTERISTICS
VCC
Condition
TA = 25°C
−40°C 3 TA 3 85°C
−55°C 3 TA 3 125°C
Symbol
Parameter
(V)
Min
Typ
Max
Min
Max
Min
Max
Units
VT)
Positive Input
Threshold Voltage
2.3
2.7
3.0
4.5
5.5
1.0
1.2
1.3
1.9
2.2
1.5
1.7
1.9
2.7
3.3
1.8
2.0
2.2
3.1
3.6
1.0
1.2
1.3
1.9
2.2
1.8
2.0
2.2
3.1
3.6
1.0
1.2
1.3
1.9
2.2
1.8
2.0
2.2
3.1
3.6
V
VT*
Negative Input
Threshold Voltage
2.3
2.7
3.0
4.5
5.5
0.4
0.5
0.6
1.0
1.2
0.75
0.87
1.0
1.5
1.9
1.15
1.4
1.5
2.0
2.3
0.4
0.5
0.6
1.0
1.2
1.15
1.4
1.5
2.0
2.3
0.4
0.5
0.6
1.0
1.2
1.15
1.4
1.5
2.0
2.3
V
VH
Input Hysteresis
Voltage
2.3
2.7
3.0
4.5
5.5
0.25
0.3
0.4
0.6
0.7
0.75
0.83
0.93
1.2
1.4
1.1
1.15
1.2
1.5
1.7
0.25
0.3
0.4
0.6
0.7
1.1
1.15
1.2
1.5
1.7
0.25
0.3
0.4
0.6
0.7
1.1
1.15
1.2
1.5
1.7
V
VOH
High−Level
Output Voltage
IOH = −100 mA
IOH = *3 mA
IOH = *8 mA
IOH = *12 mA
IOH = *16 mA
IOH = *24 mA
IOH = *32 mA
1.65 to 5.5
1.65
2.3
2.7
3.0
3.0
4.5
VCC − 0.1
1.29
1.9
2.2
2.4
2.3
3.8
VCC
1.52
2.1
2.4
2.7
2.5
4.0
IOL = 100 mA
IOL = 4 mA
IOL = 8 mA
IOL = 12 mA
IOL = 16 mA
IOL = 24 mA
IOL = 32 mA
1.65 to 5.5
1.65
2.3
2.7
3.0
3.0
4.5
VIN = VIH or VIL
VOL
Low−Level
Output Voltage
VIN = VIH or VIL
IIN
VCC − 0.1
1.29
1.9
2.2
2.4
2.3
3.8
0.08
0.2
0.22
0.28
0.38
0.42
VCC − 0.1
1.29
1.8
2.1
2.3
2.2
3.7
V
0.1
0.24
0.3
0.4
0.4
0.55
0.55
0.1
0.24
0.3
0.4
0.4
0.55
0.55
0.1
0.24
0.4
0.5
0.5
0.55
0.65
V
Input Leakage
Current
VIN = 5.5 V or
GND
0 to 5.5
±0.1
±1.0
±1.0
mA
IOFF
Power Off
Leakage Current
VIN = 5.5 V or
VOUT = 5.5 V
0
1
10
10
mA
ICC
Quiescent Supply
Current
VIN = 5.5 V or
GND
5.5
1
10
10
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns)
TA = 25°C
Symbol
tPLH
tPHL
−55°C 3 TA 3 125°C
Condition
VCC (V)
RL = 1 MW, CL = 15 pF
2.5 ± 0.2
1.8
4.3
7.4
1.8
8.1
1.8
9.1
RL = 1 MW, CL = 15 pF
RL = 500 W, CL = 50 pF
3.3 ± 0.3
1.5
1.8
3.3
4.0
5.0
6.0
1.5
1.8
5.5
6.6
1.5
1.8
6.5
7.6
RL = 1 MW, CL = 15 pF
RL = 500 W, CL = 50 pF
5.0 ± 0.5
1.0
1.2
2.7
3.2
4.1
4.9
1.0
1.2
4.5
5.4
1.0
1.2
5.5
6.4
Parameter
Propagation
Delay
Input A to Y
(Figure 3 & 4)
−40°C 3 TA 3 85°C
Min
Typ
Max
Min
Max
Min
Max
Units
ns
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
Condition
Typical
Units
CIN
Input Capacitance
VCC = 5.5 V, VI = 0 V or VCC
2.5
pF
CPD
Power Dissipation Capacitance (Note 6)
10 MHz, VCC = 3.3 V, VI = 0 V or VCC
10 MHz, VCC = 5.0 V, VI = 0 V or VCC
11
12.5
pF
6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin ) ICC. CPD is used to determine the no−load dynamic
power consumption; PD = CPD VCC2 fin ) ICC VCC.
http://onsemi.com
3
NL27WZ14
VCC
A or B
VCC
50%
GND
tPLH
Y
PULSE
GENERATOR
DUT
tPHL
RT
CL
RL
50% VCC
RT = CL or equivalent (includes jog and probe capacitance)
RT = ZOUT of pulse generator (typically 50 W)
VT , TYPICAL INPUT THRESHOLD VOLTAGE (VOLTS)
Figure 3. Switching Waveforms
Figure 4. Test Circuit
4
3
(VT))
2
VHtyp
(VT*)
1
2
2.5
3.5
3
VCC, POWER SUPPLY VOLTAGE (VOLTS)
VHtyp = (VT) typ) − (VT* typ)
3.6
Figure 5. Typical Input Threshold, VT), VT* versus Power Supply Voltage
VH
Vin
VCC
VCC
VH
VT)
VT*
VT)
VT*
Vin
GND
GND
VOH
VOH
Vout
Vout
VOL
VOL
(a) A Schmitt−Trigger Squares Up Inputs With
Slow Rise and Fall Times
(b) A Schmitt−Trigger Offers Maximum Noise Immunity
Figure 6. Typical Schmitt−Trigger Applications
http://onsemi.com
4
NL27WZ14
PACKAGE DIMENSIONS
SC−88/SC70−6/SOT−363
CASE 419B−02
ISSUE Y
2X
aaa H D
D
A
D
6
5
GAGE
PLANE
4
2
L
L2
E1
E
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH,
PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.20 PER END.
4. DIMENSIONS D AND E1 AT THE OUTERMOST EXTREMES OF
THE PLASTIC BODY AND DATUM H.
5. DATUMS A AND B ARE DETERMINED AT DATUM H.
6. DIMENSIONS b AND c APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.08 AND 0.15 FROM THE TIP.
7. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 TOTAL IN
EXCESS OF DIMENSION b AT MAXIMUM MATERIAL CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OF THE FOOT.
H
DETAIL A
3
aaa C
2X
bbb H D
2X 3 TIPS
e
B
6X
ddd
TOP VIEW
A2
A
6X
ccc C
A1
SIDE VIEW
DIM
A
A1
A2
b
C
D
E
E1
e
L
L2
aaa
bbb
ccc
ddd
b
C
M
C A-B D
DETAIL A
SEATING
PLANE
END VIEW
c
MILLIMETERS
MIN
NOM MAX
−−−
−−−
1.10
0.00
−−−
0.10
0.70
0.90
1.00
0.15
0.20
0.25
0.08
0.15
0.22
1.80
2.00
2.20
2.00
2.10
2.20
1.15
1.25
1.35
0.65 BSC
0.26
0.36
0.46
0.15 BSC
0.15
0.30
0.10
0.10
RECOMMENDED
SOLDERING FOOTPRINT*
6X
6X
0.30
0.66
2.50
0.65
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
5
INCHES
MIN
NOM MAX
−−−
−−− 0.043
0.000
−−− 0.004
0.027 0.035 0.039
0.006 0.008 0.010
0.003 0.006 0.009
0.070 0.078 0.086
0.078 0.082 0.086
0.045 0.049 0.053
0.026 BSC
0.010 0.014 0.018
0.006 BSC
0.006
0.012
0.004
0.004
NL27WZ14
PACKAGE DIMENSIONS
TSOP−6
CASE 318G−02
ISSUE V
D
H
6
E1
5
ÉÉÉ
1
NOTE 5
2
L2
4
GAUGE
PLANE
E
3
L
b
C
DETAIL Z
e
0.05
M
A
SEATING
PLANE
c
A1
DETAIL Z
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM
LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH,
PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR
GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSIONS D
AND E1 ARE DETERMINED AT DATUM H.
5. PIN ONE INDICATOR MUST BE LOCATED IN THE INDICATED ZONE.
DIM
A
A1
b
c
D
E
E1
e
L
L2
M
MIN
0.90
0.01
0.25
0.10
2.90
2.50
1.30
0.85
0.20
0°
MILLIMETERS
NOM
MAX
1.00
1.10
0.06
0.10
0.38
0.50
0.18
0.26
3.00
3.10
2.75
3.00
1.50
1.70
0.95
1.05
0.40
0.60
0.25 BSC
10°
−
RECOMMENDED
SOLDERING FOOTPRINT*
6X
0.60
6X
3.20
0.95
0.95
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
6
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NL27WZ14/D