MC74LVX257

MC74LVX257
Quad 2-Channel Multiplexer
with 3-State Outputs
The MC74LVX257 is an advanced high speed CMOS quad
2−channel multiplexer fabricated with silicon gate CMOS technology.
It consists of four 2−input digital multiplexers with common select
(S) and enable (OE) inputs. When (OE) is held High, selection of data
is inhibited and all the outputs go Low.
The select decoding determines whether the A or B inputs get routed
to the corresponding Y outputs.
The inputs tolerate voltages up to 7.0 V, allowing the interface of
5.0 V systems to 3.0 V systems.
Features
•
•
•
•
•
•
•
•
•
•
•
•
High Speed: tPD = 4.5 ns (Typ) at VCC = 3.3 V
Low Power Dissipation: ICC = 4 mA (Max) at TA = 25°C
http://onsemi.com
MARKING
DIAGRAMS
16
SOIC−16
D SUFFIX
CASE 751B
LVX257G
AWLYWW
1
16
High Noise Immunity: VNIH = VNIL = 28% VCC
LVX
257
ALYWG
G
TSSOP−16
DT SUFFIX
CASE 948F
Power Down Protection Provided on Inputs
Balanced Propagation Delays
Designed for 2.0 V to 5.5 V Operating Range
1
Low Noise: VOLP = 0.8 V (Max)
Pin and Function Compatible with Other Standard Logic Families
Latchup Performance Exceeds 300 mA
Chip Complexity: FETs = 100; Equivalent Gates = 25
ESD Performance:
Human Body Model > 2000 V;
Machine Model > 200 V
These Devices are Pb−Free and are RoHS Compliant
16
SOEIAJ−16
M SUFFIX
CASE 966
LVX257
ALYWG
1
LVX257
A
WL, L
Y
WW, W
G or G
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
© Semiconductor Components Industries, LLC, 2011
May, 2011 − Rev. 4
1
Publication Order Number:
MC74LVX257/D
MC74LVX257
I0a
S
1
16
VCC
I1a
A0
2
15
OE
I0b
B0
3
14
A3
Y0
4
13
B3
A1
5
12
Y3
B1
6
11
A2
I1b
I0c
I1c
I0d
Y1
7
10
B2
GND
8
9
Y2
I1d
OE
2
4
3
5
7
6
14
12
13
11
9
10
Za
Zb
Zc
Zd
15
Figure 1. Pin Assignment
S
1
Figure 2. Expanded Logic Diagram
OE
S
A0
B0
A1
B1
A2
B2
A3
B3
15
1
EN
G1
2
3
5
6
1
1
MUX
4
7
11
10
14
13
9
12
Y0
FUNCTION TABLE
Inputs
Y1
OE
Y2
S
Outputs
Y0 − Y3
H
X
Z
L
L
A0 −A3
L
H
B0 −B3
A0 − A3, B0 − B3 = the levels
of the respective Data−Word
Inputs.
Y3
Figure 3. IEC Logic Symbol
ORDERING INFORMATION
Package
Shipping†
MC74LVX257DG
SOIC−16
(Pb−Free)
48 Units / Rail
MC74LVX257DR2G
SOIC−16
(Pb−Free)
2500 Tape & Reel
MC74LVX257DTG
TSSOP−16*
96 Units / Rail
MC74LVX257DTR2G
TSSOP−16*
2500 Tape & Reel
MC74LVX257MG
SOEIAJ−16
50 Units / Rail
MC74LVX257MELG
SOEIAJ−16
(Pb−Free)
2000 Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
2
MC74LVX257
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VCC
Positive DC Supply Voltage
−0.5 to +7.0
V
VIN
Digital Input Voltage
−0.5 to +7.0
V
VOUT
DC Output Voltage
−0.5 to VCC +0.5
V
IIK
Input Diode Current
−20
mA
IOK
Output Diode Current
$20
mA
IOUT
DC Output Current, per Pin
$25
mA
ICC
DC Supply Current, VCC and GND Pins
$75
mA
PD
Power Dissipation in Still Air
200
180
mW
TSTG
Storage Temperature Range
−65 to +150
°C
VESD
ESD Withstand Voltage
Human Body Model (Note 1)
Machine Model (Note 2)
Charged Device Model (Note 3)
>2000
>200
>2000
V
Above VCC and Below GND at 125°C (Note 4)
$300
mA
143
164
°C/W
ILATCHU
Latchup Performance
SOIC Package
TSSOP
P
qJA
Thermal Resistance, Junction−to−Ambient
SOIC Package
TSSOP
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. Tested to EIA/JESD22−A114−A
2. Tested to EIA/JESD22−A115−A
3. Tested to JESD22−C101−A
4. Tested to EIA/JESD78
RECOMMENDED OPERATING CONDITIONS
Symbol
Characteristics
Min
Max
Unit
2.0
3.6
V
VCC
DC Supply Voltage
VIN
DC Input Voltage
0
5.5
V
DC Output Voltage
0
VCC
V
−40
85
°C
0
100
ns/V
VOUT
TA
Operating Temperature Range, all Package
Types
tr, tf
Input Rise or Fall Time
VCC = 3.3 V + 0.3 V
http://onsemi.com
3
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V CC ).
Unused outputs must be left open.
MC74LVX257
DC CHARACTERISTICS (Voltages Referenced to GND)
VCC
Symbol
Parameter
Condition
TA = 25°C
(V)
Min
0.75 VCC
0.7 VCC
0.7 VCC
VIH
Minimum High−Level
Input Voltage
2.0
3.0
3.6
VIL
Maximum Low−Level
Input Voltage
2.0
3.0
3.6
VOH
High−Level Output
Voltage
IOH = −50 mA
IOH = −50 mA
IOH = −4 mA
2.0
3.0
3.0
VOL
Low−Level Output
Voltage
IOL = 50 mA
IOL = 50 mA
IOL = 4 mA
2.0
3.0
3.0
IOZ
Maximum 3−State
Leakage Current
VIN = VIH or VIL
VOUT = VCC or GND
IIN
Input Leakage Current
ICC
Maximum Quiescent
Supply Current
(per package)
Typ
−40°C ≤ TA ≤ 85°C
Max
Min
0.75 VCC
0.7 VCC
0.7 VCC
0.25 VCC
0.3 VCC
0.3 VCC
1.9
2.9
2.58
Max
2.0
3.0
0.0
0.0
Unit
V
0.25 VCC
0.3 VCC
0.3 VCC
1.9
2.9
2.48
V
V
0.1
0.1
0.36
0.1
0.1
0.44
V
3.6
±0.1
±1.0
mA
VIN = 5.5 V or GND
0 to 3.6
±0.1
±1.0
mA
VIN = VCC or GND
3.6
2.0
40
mA
1.0
1.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
AC ELECTRICAL CHARACTERISTICS Input tr = tf = 3.0 ns
TA = 25°C
Symbol
tPLH,
tPHL
tPLH,
tPHL
tPZL,
tPZH
tPLZ,
tPHZ
CIN
Parameter
Maximum Propagation
Delay, A or B to Y
Maximum Propagation
Delay, S to Y
Maximum Output
Enable, Time, OE to Y
Maximum Output
Disable, Time, OE to Y
Min
Test Conditions
−40°C ≤ TA ≤ 85°C
Typ
Max
Min
Max
Unit
ns
VCC = 2.7 V
CL = 15pF
CL = 50pF
6.5
9.5
10.0
14.0
1.0
1.0
15.0
18.5
VCC = 3.3 V ± 0.3 V
CL = 15pF
CL = 50pF
4.5
7.5
8.0
12.0
1.0
1.0
10.0
13.5
VCC = 2.7 V
CL = 15pF
CL = 50pF
8.0
10.5
12.0
15.5
1.0
1.0
17.0
20.0
VCC = 3.3 V ± 0.3 V
CL = 15pF
CL = 50pF
6.0
8.5
10.0
13.5
1.0
1.0
12.0
15.5
VCC = 2.7 V
RL = 1 kW
CL = 15pF
CL = 50pF
7.5
10.5
11.5
15.0
1.0
1.0
16.5
18.0
VCC = 3.3 V ± 0.3 V
RL = 1 kW
CL = 15pF
CL = 50pF
5.5
8.5
9.5
13.0
1.0
1.0
11.5
15.0
VCC = 2.7
RL = 1 kW
CL = 50pF
13.0
17.0
1.0
18.0
VCC = 3.3 V ± 0.3 V
RL = 1 kW
CL = 50pF
12
17.0
1.0
18.0
4
10
Maximum Input
Capacitance
10
ns
ns
ns
pF
Typical @ 25°C, VCC = 3.3 V
CPD
20
Power Dissipation Capacitance (Note 5)
pF
5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic
power consumption; PD = CPD VCC2 fin + ICC VCC.
http://onsemi.com
4
MC74LVX257
NOISE CHARACTERISTICS Input tr = tf = 3.0 ns, CL = 50 pF, VCC = 3.3 V
TA = 25°C
Symbol
Characteristic
Typ
Max
Unit
VOLP
Quiet Output Maximum Dynamic VOL
0.3
0.5
V
VOLV
Quiet Output Minimum Dynamic VOL
−0.3
−0.5
V
VIHD
Minimum High Level Dynamic Input Voltage
2.0
V
VILD
Maximum Low Level Dynamic Input Voltage
0.8
V
VCC
OE
50%
GND
VCC
A, B or S
50%
tPLH
Y
tPZL
GND
tPHL
tPLZ
50% VCC
Y
tPZH
50% VCC
VOH - 0.3V
HIGH
IMPEDANCE
Figure 5. Switching Waveform
TEST POINT
TEST POINT
OUTPUT
DEVICE
UNDER
TEST
VOL + 0.3V
tPHZ
50% VCC
Y
Figure 4. Switching Waveform
HIGH
IMPEDANCE
DEVICE
UNDER
TEST
CL*
*Includes all probe and jig capacitance
OUTPUT
1 kW
CL *
CONNECT TO VCC WHEN
TESTING tPLZ AND tPZL.
CONNECT TO GND WHEN
TESTING tPHZ AND tPZH.
*Includes all probe and jig capacitance
Figure 6. Test Circuit
Figure 7. Test Circuit
INPUT
Figure 8. Input Equivalent Circuit
http://onsemi.com
5
MC74LVX257
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
9
−B−
1
P
8 PL
0.25 (0.010)
8
M
B
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
http://onsemi.com
6
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
MC74LVX257
PACKAGE DIMENSIONS
TSSOP−16
CASE 948F−01
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
S
V
S
K
S
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
8
1
0.25 (0.010)
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
http://onsemi.com
7
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
MC74LVX257
PACKAGE DIMENSIONS
SOEIAJ−16
CASE 966−01
ISSUE A
16
LE
9
Q1
E HE
1
M_
L
8
Z
DETAIL P
D
e
VIEW P
A
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
A1
b
0.13 (0.005)
c
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE
MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD FLASH
OR PROTRUSIONS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
0.10 (0.004)
MILLIMETERS
MIN
MAX
--2.05
0.05
0.20
0.35
0.50
0.10
0.20
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 _
0_
0.70
0.90
--0.78
INCHES
MIN
MAX
--0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 _
0_
0.028
0.035
--0.031
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74LVX257/D