MC14511B D

MC14511B
BCD-to-Seven Segment
Latch/Decoder/Driver
The MC14511B BCD−to−seven segment latch/decoder/driver is
constructed with complementary MOS (CMOS) enhancement mode
devices and NPN bipolar output drivers in a single monolithic structure.
The circuit provides the functions of a 4−bit storage latch, an 8421
BCD−to−seven segment decoder, and an output drive capability. Lamp
test (LT), blanking (BI), and latch enable (LE) inputs are used to test the
display, to turn−off or pulse modulate the brightness of the display, and
to store a BCD code, respectively. It can be used with seven−segment
light−emitting diodes (LED), incandescent, fluorescent, gas discharge,
or liquid crystal readouts either directly or indirectly.
Applications include instrument (e.g., counter, DVM, etc.) display
driver, computer/calculator display driver, cockpit display driver, and
various clock, watch, and timer uses.
http://onsemi.com
SOIC−16
D SUFFIX
CASE 751B
SOEIAJ−16
F SUFFIX
CASE 966
MARKING DIAGRAMS
16
16
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Low Logic Circuit Power Dissipation
High−Current Sourcing Outputs (Up to 25 mA)
Latch Storage of Code
Blanking Input
Lamp Test Provision
Readout Blanking on all Illegal Input Combinations
Lamp Intensity Modulation Capability
Time Share (Multiplexing) Facility
Supply Voltage Range = 3.0 V to 18 V
Capable of Driving Two Low−power TTL Loads, One Low−power
Schottky TTL Load, or Two HTL Loads Over the Rated Temperature
Range
Chip Complexity: 216 FETs or 54 Equivalent Gates
Triple Diode Protection on all Inputs
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and are RoHS Compliant
SO−16 WB
DW SUFFIX
CASE 751G
MC14511B
ALYWG
14511BG
AWLYWW
1
1
SOIC−16
SOEIAJ−16
16
14511B
AWLYYWWG
1
SO−16 WB
A
WL, L
YY, Y
WW, W
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 1)
Parameter
Symbol
Value
Unit
−0.5 to +18.0
V
VDD
DC Supply Voltage Range
Vin
Input Voltage Range, All Inputs
−0.5 to VDD + 0.5
V
I
DC Current Drain per Input Pin
10
mA
PD
Power Dissipation, per Package (Note 2)
500
mW
TA
Operating Temperature Range
−55 to +125
°C
Tstg
Storage Temperature Range
−65 to +150
°C
IOHmax
Maximum Output Drive Current (Source) per Output
25
mA
POHmax
Maximum Continuous Output Power (Source) per Output (Note 3)
50
mA
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Maximum Ratings are those values beyond which damage to the device may occur.
2. Temperature Derating: “D/DW” Packages: –7.0 mW/°C From 65°C to 125°C
3. POHmax = IOH (VDD − VOH)
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 12
1
Publication Order Number:
MC14511B/D
MC14511B
This device contains protection circuitry to protect the
inputs against damage due to high static voltages or electric
fields. However, it is advised that normal precautions be
taken to avoid application of any voltage higher than
maximum rated voltages to this high−impedance circuit.
A destructive high current mode may occur if Vin and Vout
are not constrained to the range VSS ≤ (Vin or Vout) ≤ VDD.
Due to the sourcing capability of this circuit, damage can
occur to the device if VDD is applied, and the outputs are
shorted to VSS and are at a logical 1 (See Maximum
Ratings).
Unused inputs must always be tied to an appropriate logic
voltage level (e.g., either VSS or VDD).
PIN ASSIGNMENT
B
1
16
VDD
C
2
15
f
LT
3
14
g
BI
4
13
a
LE
5
12
b
D
6
11
c
A
7
10
d
VSS
8
9
e
a
f
g
e
b
c
d
DISPLAY
0
1
2
3
4
5
6
7
8
9
TRUTH TABLE
LE BI LT
X X 0
X 0 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
0
1 1
1
1 1
Inputs
D
C
X
X
X
X
0
0
0
0
0
0
0
0
0
1
0
1
0
1
0
1
1
0
1
0
1
0
1
0
1
1
1
1
1
1
1
1
X
X
B
X
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
X
A
X
X
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
X
a
1
0
1
0
1
1
0
1
0
1
1
1
0
0
0
0
0
0
b
1
0
1
1
1
1
1
0
0
1
1
1
0
0
0
0
0
0
c
1
0
1
1
0
1
1
1
1
1
1
1
0
0
0
0
0
0
d
1
0
1
0
1
1
0
1
1
0
1
0
0
0
0
0
0
0
*
Outputs
e
f
1
1
0
0
1
1
0
0
1
0
0
0
0
1
0
1
1
1
0
0
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
X = Don’t Care
* Depends upon the BCD code previously applied when LE = 0
http://onsemi.com
2
g
1
0
0
0
1
1
1
1
1
0
1
1
0
0
0
0
0
0
Display
8
Blank
0
1
2
3
4
5
6
7
8
9
Blank
Blank
Blank
Blank
Blank
Blank
*
MC14511B
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
− 55°C
25°C
VDD
125°C
Symbol
Vdc
Min
Max
Min
Typ
(Note 4)
“0” Level
VOL
5.0
10
15
−
−
−
0.05
0.05
0.05
−
−
−
0
0
0
0.05
0.05
0.05
−
−
−
0.05
0.05
0.05
Vdc
“1” Level
VOH
5.0
10
15
4.1
9.1
14.1
−
−
−
4.1
9.1
14.1
4.57
9.58
14.59
−
−
−
4.1
9.1
14.1
−
−
−
Vdc
Input Voltage #
“0” Level
(VO = 3.8 or 0.5 Vdc)
(VO = 8.8 or 1.0 Vdc)
(VO = 13.8 or 1.5 Vdc)
VIL
5.0
10
15
−
−
−
1.5
3.0
4.0
−
−
−
2.25
4.50
6.75
1.5
3.0
4.0
−
−
−
1.5
3.0
4.0
“1” Level
VIH
5.0
10
15
3.5
7.0
11
−
−
−
3.5
7.0
11
2.75
5.50
8.25
−
−
−
3.5
7.0
11
−
−
−
5.0
4.1
−
3.9
−
3.4
−
−
−
−
−
−
−
4.1
−
3.9
−
3.4
−
4.57
4.24
4.12
3.94
3.70
3.54
−
−
−
−
−
−
4.1
−
3.5
−
3.0
−
−
−
−
−
−
−
(IOH = 0 mA)
(IOH = 5.0 mA)
(IOH = 10 mA)
(IOH = 15 mA)
(IOH = 20 mA)
(IOH = 25 mA)
10
9.1
−
9.0
−
8.6
−
−
−
−
−
−
−
9.1
−
9.0
−
8.6
−
9.58
9.26
9.17
9.04
8.90
8.70
−
−
−
−
−
−
9.1
−
8.6
−
8.2
−
−
−
−
−
−
−
Vdc
(IOH = 0 mA)
(IOH = 5.0 mA)
(IOH = 10 mA)
(IOH = 15 mA)
(IOH = 20 mA)
(IOH = 25 mA)
15
14.1
−
14
−
13.6
−
−
−
−
−
−
−
14.1
−
14
−
13.6
−
14.59
14.27
14.18
14.07
13.95
13.70
−
−
−
−
−
−
14.1
−
13.6
−
13.2
−
−
−
−
−
−
−
Vdc
5.0
10
15
0.64
1.6
4.2
−
−
−
0.51
1.3
3.4
0.88
2.25
8.8
−
−
−
0.36
0.9
2.4
−
−
−
15
−
± 0.1
−
± 0.00001
± 0.1
−
± 1.0
Characteristic
Output Voltage
Vin = VDD or 0
Vin = 0 or VDD
(VO = 0.5 or 3.8 Vdc)
(VO = 1.0 or 8.8 Vdc)
(VO = 1.5 or 13.8 Vdc)
Output Drive Voltage
(IOH = 0 mA)
(IOH = 5.0 mA)
(IOH = 10 mA)
(IOH = 15 mA)
(IOH = 20 mA)
(IOH = 25 mA)
Output Drive Current
(VOL = 0.4 V)
(VOL = 0.5 V)
(VOL = 1.5 V)
Max
Min
Max
Unit
Vdc
Vdc
VOH
Source
Vdc
IOL
Sink
Input Current
Iin
mAdc
mAdc
Input Capacitance
Cin
−
−
−
−
5.0
7.5
−
−
pF
Quiescent Current
(Per Package) Vin = 0 or VDD,
Iout = 0 mA
IDD
5.0
10
15
−
−
−
5.0
10
20
−
−
−
0.005
0.010
0.015
5.0
10
20
−
−
−
150
300
600
mAdc
Total Supply Current (Notes 5 & 6)
(Dynamic plus Quiescent,
Per Package)
(CL = 50 pF on all outputs, all
buffers switching)
IT
5.0
10
15
IT = (1.9 mA/kHz) f + IDD
IT = (3.8 mA/kHz) f + IDD
IT = (5.7 mA/kHz) f + IDD
mAdc
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
4. Noise immunity specified for worst−case input combination.
Noise Margin for both “1” and “0” level =
1.0 Vdc min @ VDD = 5.0 Vdc
2.0 Vdc min @ VDD = 10 Vdc
2.5 Vdc min @ VDD = 15 Vdc
5. The formulas given are for the typical characteristics only at 25°C.
6. To calculate total supply current at loads other than 50 pF:
IT(CL) = IT(50 pF) + 3.5 x 10–3 (CL – 50) VDDf
where: IT is in mA (per package), CL in pF, VDD in Vdc, and f in kHz is input frequency.
http://onsemi.com
3
MC14511B
SWITCHING CHARACTERISTICS (Note 7) (CL = 50 pF, TA = 25°C)
VDD
Vdc
Min
Typ
Max
5.0
10
15
−
−
−
40
30
25
80
60
50
5.0
10
15
−
−
−
125
75
65
250
150
130
5.0
10
15
−
−
−
640
250
175
1280
500
350
5.0
10
15
−
−
−
720
290
200
1440
580
400
5.0
10
15
−
−
−
600
200
150
750
300
220
5.0
10
15
−
−
−
485
200
160
970
400
320
5.0
10
15
−
−
−
313
125
90
625
250
180
tPHL
5.0
10
15
−
−
−
313
125
90
625
250
180
Setup Time
tsu
5.0
10
15
100
40
30
−
−
−
−
−
−
ns
Hold Time
th
5.0
10
15
60
40
30
−
−
−
−
−
−
ns
tWL
5.0
10
15
520
220
130
260
110
65
−
−
−
ns
Characteristic
Symbol
Output Rise Time
tTLH = (0.40 ns/pF) CL + 20 ns
tTLH = (0.25 ns/pF) CL + 17.5 ns
tTLH = (0.20 ns/pF) CL + 15 ns
tTLH
Output Fall Time
tTHL = (1.5 ns/pF) CL + 50 ns
tTHL = (0.75 ns/pF) CL + 37.5 ns
tTHL = (0.55 ns/pF) CL + 37.5 ns
tTHL
Data Propagation Delay Time
tPLH = (0.40 ns/pF) CL + 620 ns
tPLH = (0.25 ns/pF) CL + 237.5 ns
tPLH = (0.20 ns/pF) CL + 165 ns
tPHL = (1.3 ns/pF) CL + 655 ns
tPHL = (0.60 ns/pF) CL + 260 ns
tPHL = (0.35 ns/pF) CL + 182.5 ns
tPLH
Blank Propagation Delay Time
tPLH = (0.30 ns/pF) CL + 585 ns
tPLH = (0.25 ns/pF) CL + 187.5 ns
tPLH = (0.15 ns/pF) CL + 142.5 ns
tPHL = (0.85 ns/pF) CL + 442.5 ns
tPHL = (0.45 ns/pF) CL + 177.5 ns
tPHL = (0.35 ns/pF) CL + 142.5 ns
tPLH
Lamp Test Propagation Delay Time
tPLH = (0.45 ns/pF) CL + 290.5 ns
tPLH = (0.25 ns/pF) CL + 112.5 ns
tPLH = (0.20 ns/pF) CL + 80 ns
tPHL = (1.3 ns/pF) CL + 248 ns
tPHL = (0.45 ns/pF) CL + 102.5 ns
tPHL = (0.35 ns/pF) CL + 72.5 ns
tPLH
ns
ns
ns
tPHL
ns
tPHL
Latch Enable Pulse Width
Unit
ns
7. The formulas given are for the typical characteristics only.
http://onsemi.com
4
MC14511B
Input LE low, and Inputs D, BI and LT high.
f in respect to a system clock.
All outputs connected to respective CL loads.
20 ns
20 ns
90%
50%
1
2f
A, B, AND C
VDD
10%
VSS
50% DUTY CYCLE
VOH
50%
ANY OUTPUT
VOL
Figure 1. Dynamic Power Dissipation Signal Waveforms
20 ns
20 ns
20 ns
VDD
90%
50%
10%
INPUT C
10%
th
VDD
VOH
90%
INPUT C
50%
VSS
50%
OUTPUT g
VSS
tsu
VSS
tPHL
tPLH
LE
VDD
90%
50%
10%
VOL
VOH
OUTPUT g
tTHL
tTLH
VOL
(b) Input D low,
Inputs A, B, BI and LT high.
(a) Inputs D and LE low, and
Inputs A, B, BI and LT high.
20 ns
20 ns
LE
VDD
90%
50%
10%
tWL
(c) Data DCBA strobed into latches.
Figure 2. Dynamic Signal Waveforms
http://onsemi.com
5
VSS
MC14511B
CONNECTIONS TO VARIOUS DISPLAY READOUTS
LIGHT EMITTING DIODE (LED) READOUT
VDD
VDD
COMMON
ANODE LED
COMMON
CATHODE LED
≈ 1.7 V
≈ 1.7 V
VSS
VSS
INCANDESCENT READOUT
VDD
FLUORESCENT READOUT
VDD
VDD
**
DIRECT
(LOW BRIGHTNESS)
FILAMENT
SUPPLY
VSS
VSS
VSS OR APPROPRIATE
VOLTAGE BELOW VSS.
(CAUTION: Maximum working voltage = 18.0 V)
GAS DISCHARGE READOUT
VDD
LIQUID CRYSTAL (LCD) READOUT
APPROPRIATE
VOLTAGE
EXCITATION
(SQUARE WAVE,
VSS TO VDD)
VDD
1/4 OF MC14070B
VSS
VSS
** A filament pre−warm resistor is recommended to reduce filament
thermal shock and increase the effective cold resistance of the
filament.
Direct DC drive of LCD’s not recommended for life of
LCD readouts.
http://onsemi.com
6
MC14511B
BI4
13a
A7
12b
11c
B1
10d
9e
15f
C2
14g
LT3
D6
VDD = PIN 16
VSS = PIN 8
LE5
Figure 3. Logic Diagram
ORDERING INFORMATION
Package
Shipping†
MC14511BDG
SOIC−16
(Pb−Free)
48 Units / Rail
MC14511BDR2G
SOIC−16
(Pb−Free)
2500 / Tape & Reel
MC14511BDWR2G
SO−16 WB
(Pb−Free)
1000 / Tape & Reel
NLV14511BDWR2G*
SO−16 WB
(Pb−Free)
1000 / Tape & Reel
MC14511BFG
SOEIAJ−16
(Pb−Free)
50 Units / Rail
MC14511BFELG
SOEIAJ−16
(Pb−Free)
2000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
7
MC14511B
PACKAGE DIMENSIONS
SOIC−16
PLASTIC SOIC PACKAGE
CASE 751B−05
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
−A−
16
9
−B−
1
P
8 PL
0.25 (0.010)
8
M
B
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
http://onsemi.com
8
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
MC14511B
PACKAGE DIMENSIONS
SOIC−16 WB
CASE 751G−03
ISSUE D
A
D
9
1
8
h X 45 _
E
0.25
16X
M
T A
MILLIMETERS
DIM MIN
MAX
A
2.35
2.65
A1 0.10
0.25
B
0.35
0.49
C
0.23
0.32
D 10.15 10.45
E
7.40
7.60
e
1.27 BSC
H 10.05 10.55
h
0.25
0.75
L
0.50
0.90
q
0_
7_
S
B
S
L
A
0.25
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INLCUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 TOTAL IN
EXCESS OF THE B DIMENSION AT MAXIMUM
MATERIAL CONDITION.
B
B
14X
e
A1
H
8X
M
B
M
16
q
C
T
SEATING
PLANE
SOLDERING FOOTPRINT
16X
0.58
11.00
1
16X
1.27
PITCH
1.62
DIMENSIONS: MILLIMETERS
http://onsemi.com
9
MC14511B
PACKAGE DIMENSIONS
SOEIAJ−16
CASE 966
ISSUE A
16
LE
9
Q1
M_
E HE
1
L
8
DETAIL P
Z
D
e
VIEW P
A
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
A1
b
0.13 (0.005)
c
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
0.10 (0.004)
MILLIMETERS
MIN
MAX
--2.05
0.05
0.20
0.35
0.50
0.10
0.20
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 _
0_
0.70
0.90
--0.78
INCHES
MIN
MAX
--0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 _
0_
0.028
0.035
--0.031
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC14511B/D