2SA2153 Bipolar Transistor −50V, −2A, Low VCE(sat), PNP Single www.onsemi.com Features • Adoption of MBIT Process • Low Saturation Voltage • Large Current Capacity and Wide ASO ELECTRICAL CONNECTION 2 Typical Applications • Voltage Regulators • Relay Drivers • Lamp Drivers • Electrical Equipment 1 : Base 2 : Collector 3 : Emitter 1 3 SPECIFICATIONS ABSOLUTE MAXIMUM RATING at Ta = 25°C (Note 1, 2) April 2016 - Rev. 2 Value 1 1 2 LOT No. Unit −50 V −50 V −6 V −2 A −4 A −400 mA (Note 2) 1.3 W Collector Dissipation PC Tc=25°C 3.5 W Junction Temperature Tj 150 °C Storage Temperature Tstg −55 to +150 °C Note 1 : Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 2 Note 2 : Surface mounted on ceramic substrate(450mm × 0.8mm) © Semiconductor Components Industries, LLC, 2016 Symbol VCBO VCEO VEBO IC ICP IB AZ Parameter Collector to Base Voltage Collector to Emitter Voltage Emitter to Base Voltage Collector Current Collector Current (Pulse) Base Current MARKING 3 SOT-89 / PCP-1 1 2 3 ORDERING INFORMATION See detailed ordering and shipping information on page 5 of this data sheet. Publication Order Number : 2SA2153/D 2SA2153 ELECTRICAL CHARACTERISTICS at Ta = 25°C (Note 3) Parameter Symbol Conditions Value min typ max Unit Collector Cutoff Current ICBO VCB=−40V, IE=0A −1 μA Emitter Cutoff Current IEBO VEB=−4V, IC=0A −1 μA DC Current Gain hFE1 hFE2 VCE=−2V, IC=−100mA VCE=−2V,IC=−1.5A Gain-Bandwidth Product fT VCE=−10V, IC=−300mA Output Capacitance Cob VCB=−10V, f=1MHz Collector to Emitter Saturation Voltage VCE(sat) IC=−1A, IB=−50mA −0.2 −0.4 V Base to Emitter Saturation Voltage VBE(sat) IC=−1A, IB=−50mA −0.9 −1.2 V V(BR)CBO IC=−10μA, IE=0A −50 V V(BR)CEO IC=−1mA, RBE=∞ −50 V Emitter to Base Breakdown Voltage V(BR)EBO IE=−10μA, IC=0A −6 Turn-On Time ton tstg Collector to Base Breakdown Voltage Collector to Emitter Breakdown Voltage Storage Time See specified Test Circuit 200 560 40 420 MHz 16 pF V 35 ns 200 ns Fall Time 24 tf ns Note 3 : Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Switching Time Test Circuit www.onsemi.com 2 2SA2153 www.onsemi.com 3 2SA2153 www.onsemi.com 4 2SA2153 PACKAGE DIMENSIONS unit : mm SOT-89 / PCP-1 CASE 419AU ISSUE O 1 : Base 2 : Collector 3 : Emitter Recommended Soldering Footprint 0.9 2.2 3.7 45° 45° 1.0 1.8 1.5 1.0 1.5 3.0 ORDERING INFORMATION Device 2SA2153-TD-E Marking Package Shipping (Qty / Packing) AZ SOT-89 / PCP-1 (Pb-Free) 1,000 / Tape & Reel † For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://www.onsemi.com/pub_link/Collateral/BRD8011-D.PDF ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf . SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. www.onsemi.com 5