IPC-200 200W Industrial 1U ATX 12V/P4 PC Power Supply Features : Meet 1U rack mount system Universal AC input / Full range Active power factor 94% Protections:Short circuit/Overload/Over voltage Forced air cooling by built-in DC fan With power good and fail signal output Built-in remote ON-OFF control Remote DC sense +5V and +3.3V With +5VSB:0 ~ 2.0A max. 100% full load burn-in test High efficiency 2 years warranty SPECIFICATION MODEL IPC-200 OUTPUT NUMBER CH1 CH2 CH3 CH4 CH5 DC VOLTAGE 3.3V 5V 12V -5V -12V 5VSB RATED CURRENT 15A 25A 13A 0.5A 1A 2A CURRENT RANGE 0 ~ 15A 1 ~ 25A 1 ~ 13A 0 ~ 0.5A 0.1 ~ 1A 0 ~ 2A RATED POWER OUTPUT 200W continue. Combine power max.:+5V,+3.3V,+12V output shall not exceed 180W max. (The +5 & +3.3Volt combine total output shall not exceed 150W) (The -5 & -12Volt combine total output shall not exceed 12W) RIPPLE & NOISE (max.) Note.2 50mVp-p VOLTAGE ADJ. RANGE 50mVp-p 120mVp-p 100mVp-p 5.0% 7.0% 8.0% 10% 5.0% 1.0% 1.0% 1.0% 2.0% 2.0% 1.0% LOAD REGULATION 5.0% 5.0% 7.0% 8.0% 10% 5.0% 800ms, 20ms/230VAC HOLD TIME (Typ.) 16ms/230VAC VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz 2500ms, 20ms/115VAC at full load 16ms/115VAC at full load EFFICIENCY (Typ.) 74.5% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 3.5A/115VAC 1.7A/230VAC 40A/115VAC 3mA/240VAC 80A/230VAC LEAKAGE CURRENT(max.) OVER LOAD 105 ~ 150% rated output power Protection type : Shut down o/p voltage, re-power on to recover PROTECTION OVER VOLTAGE +3.3V, +5V: 110% ~ 140% of rated voltage ; +12V:13.2V ~ 16V Protection type : Shut down o/p voltage, re-power on to recover SHORT CIRCUIT All output equipped with short circuit Protection type : Shut down o/p voltage, re-power on to recover POWER GOOD SIGNAL POWER FAIL SIGNAL PS-ON INPUT SIGNAL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE (Note 4) EMC EMISSION EMC IMMUNITY MTBF CONNECTOR OTHERS COOLING DIMENSION PACKING NOTE 50mVp-p LINE REGULATION SETUP, RISE TIME FUNCTION 120mVp-p CH2 : 5.05 ~ 5.5V VOLTAGE TOLERANCE Note.3 CH1: 5.0% INPUT STANDBY The TTL compatible signal out with 100ms to 500ms delay after power set up The TTL compatible signal will go down at least 1ms before +5V below 4.75V Power off: PS-ON = "Hi" or ">2V" ; Power on: PS-ON = "Low" or "<0.5V" -10 ~ +60 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -40 ~ +85 10 ~ 95% RH 0.05% / (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved I/P-O/P:1.5KVAC I/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:50M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022 (CISPR22) Class B, Design refer to FCC part 15 Class B, EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A 94.1K hrs min. MIL-HDBK-217F (25 ) ATX main power connector * 1ea; +12V power connector * 1ea Peripheral power connector * 3ea; Floppy drive power connector * 1ea Forced air ventilation by 4cm DC fan 240*83*40mm (L*W*H) 1.44Kg; 10pcs/15.4Kg/0.89CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Load regulation is measured from 20% to 100% max. Load. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name: IPC-200-SPEC 2011-12-20 IPC-200 200W Industrial 1U ATX 12V/P4 PC Power Supply Mechanical Specification Case No. IPC-250 Unit:mm 4.75 40 19.5 SVR 83 72.7 Air flow direction 7 M3 4 2-M3 240 PIN1 (A) PIN11 +3.3V(ORANGE) +3.3V(ORANGE) GND(BLACK) +5V(RED) GND(BLACK) +5V(RED) GND(BLACK) PG(GRAY) +5VSB(PURPLE) +12V(YELLOW) +3.3V(ORANGE) -12V(BLUE) GND(BLACK) PS-ON(GREEN) GND(BLACK) GND(BLACK) GND(BLACK) -5V(WHITE) +5V(RED) +5V(RED) (WIRE OUTPUT OF PCB, 18AWG) L=450mm 10mm PIN10 PIN20 (B) +5VDC(RED) GND(BLACK) GND(BLACK) +12V(YELLOW) 4 3 2 1 (B) +5VDC(RED) GND(BLACK) GND(BLACK) +12V(YELLOW) 4 3 2 1 (B) +5VDC(RED) GND(BLACK) GND(BLACK) +12V(YELLOW) 4 3 2 1 L=150mm L=150mm 10mm (A)MOLEX 39-01-2200 or equivalent L=150mm (C) +5VDC(RED) GND(BLACK) GND(BLACK) +12V(YELLOW) +12V(YELLOW) 3 4 +12V(YELLOW) (D) GND(BLACK) 1 2 GND(BLACK) (B)MOLEX 8981-04P or equivalent (C)AMP 171822-4 or equivalent L=150mm (D)MOLEX 39-01-2040 or equivalent 1 2 3 4 L=440mm 10mm File Name: IPC-200-SPEC 2011-12-20 IPC-200 200W Industrial 1U ATX 12V/P4 PC Power Supply Block Diagram fosc : 100KHz +5VSB DETERCTION CIRCUIT RECTIFIERS & FILTER POWER SWITCHING PWM CONTROL +5VSB RECTIFIERS & FILTER MA & CONTROL ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & P.F.C. POWER SWITCHING +3.3V RECTIFIERS & FILTER +5V,+12V,-5V,-12V COM P.G. DETECTION CIRCUIT FG O.L.P. PWM CONTROL PG DETECTION & O.V.P. CIRCUIT PS/ON CONTROL Derating Curve PS/ON Output Derating VS Input Voltage 100 100 90 80 80 70 LOAD(%) LOAD (%) 60 40 20 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 90 100 115 135 155 230 264 INPUT VOLTAGE (V) 60Hz File Name: IPC-200-SPEC 2011-12-20