HS-6664RH TM Data Sheet August 2000 File Number Radiation Hardened 8K x 8 CMOS PROM Features The Intersil HS-6664RH is a radiation hardened 64K CMOS PROM, organized in an 8K word by 8-bit format. The chip is manufactured using a radiation hardened CMOS process, and utilizes synchronous circuit design techniques to achieve high speed performance with very low power dissipation. • Electrically Screened to SMD # 5962-95626 On-chip address latches are provided, allowing easy interfacing with microprocessors that use a multiplexed address/data bus structure. The output enable control (G) simplifies system interfacing by allowing output data bus control in addition to the chip enable control (E). All bits are manufactured storing a logical “0” and can be selectively programmed for a logical “1” at any bit location. 3197.4 • QML Qualified per MIL-PRF-38535 Requirements • 1.2 Micron Radiation Hardened Bulk CMOS • Total Dose . . . . . . . . . . . . . . . . . . . . . . 300 krad(Si) (Max) • Transient Output Upset. . . . . . . . . . . . . .>5 x 108 rad(Si)/s • LET >100 MEV-cm2/mg • Fast Access Time . . . . . . . . . . . . . . . . . . . . . . . 35ns (Typ) • Single 5V Power Supply • Single Pulse 10V Field Programmable • Synchronous Operation Applications for the HS-6664RH CMOS PROM include low power microprocessor based instrumentation and communications systems, remote data acquisition and processing systems, and processor control storage. • On-Chip Address Latches Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed here must be used when ordering. • Low Standby Current . . . . . . . . . . . . . . <500µA (Pre-Rad) Detailed Electrical Specifications for these devices are contained in SMD 5962-95626. A “hot-link” is provided on our homepage for downloading. www.intersil.com/spacedefense/space.htm • Three-State Outputs • NiCr Fuses • Low Operating Current . . . . . . . . . . . . . . . . . . <15mA/MHz • Military Temperature Range . . . . . . . . . . . -55oC to 125oC Ordering Information ORDERING NUMBER INTERNAL MKT. NUMBER TEMP. RANGE (oC) 5962F9562601QXC HS1-6664RH-8 -55 to 125 5962F9562601QYC HS9-6664RH-8 -55 to 125 5962F9562601VXC HS1-6664RH-Q -55 to 125 5962F9562601VYC HS9-6664RH-Q -55 to 125 HS1-6664RH/PROTO HS1-6664RH/PROTO -55 to 125 HS9-6664RH/PROTO HS9-6664RH/PROTO -55 to 125 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000 HS-6664RH Pinouts 28 LEAD CERAMIC (SBDIP) CASE OUTLINE D28.6 MIL-STD-1835, CDIP2-T28 TOP VIEW 28 LEAD FLATPACK CASE OUTLINE K28.A MIL-STD-1835, CDFP3-F28 TOP VIEW 28 VDD NC 1 NC 1 28 VDD † A12 2 27 P A7 3 26 NC A7 3 26 NC A6 4 25 A8 A6 4 25 A8 A5 5 24 A9 A5 5 24 A9 A4 6 23 A11 A4 6 23 A11 A3 7 22 G A3 7 22 G A2 8 21 A10 A2 8 21 A10 A1 9 20 A1 9 20 E 27 P A12 2 A0 10 19 E DQ7 DQ0 11 A0 10 19 DQ7 18 DQ6 DQ1 12 17 DQ5 DQ0 11 18 DQ6 DQ2 13 16 DQ4 DQ1 12 17 DQ5 GND 14 15 DQ3 DQ2 13 16 DQ4 GND 14 15 DQ3 † P must be hardwired at all times to VDD, except during programming. Functional Diagram MSB A2 A3 A4 A5 A6 A7 A8 LSB A LATCHED ADDRESS REGISTER 8 A 256 256 X 256 MATRIX GATED ROW DECODER 1 OF 8 8 E E 32 32 †P 32 32 32 32 32 32 GATED COLUMN DECODER PROGRAMMING, AND DATA OUTPUT CONTROL 8 8 E E A A 5 5 G E LATCHED ADDRESS REGISTER MSB LSB A0 NOTE: †€ A1 A10 A9 † P must be hardwired at all times to VDD, except during programming. TRUTH TABLE 2 E G MODE 0 0 Enabled 0 1 Output Disabled 1 X Disabled A11 A12 Q0 - Q7 HS-6664RH Burn-In Circuits HS1-6664RH 28 LEAD (8K X 8 PROM DIP) HS9-6664RH 28 LEAD (8K X 8 PROM FLATPACK) HS1-6664RH 28 LEAD (8K X 8 PROM DIP) HS9-6664RH 28 LEAD (8K X 8 PROM FLATPACK) VDD NC NC A12 A7 A6 A5 A4 A3 A2 A1 A0 NC NC NC DQ0 DQ1 DQ2 VSS 1 28 2 27 3 26 25 4 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 VDD VDD NC P A12 F13 NC NC A8 A7 F8 A6 F7 A9 A5 F6 A11 A4 F5 G A3 F4 A10 DQ7 DQ6 DQ5 DQ4 DQ3 A2 F3 E1 A1 F2 NC NC A0 F1 NC LOAD NC LOAD NC LOAD DQ0 DQ1 DQ2 VSS NC 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 20 9 10 19 11 18 12 17 13 16 14 15 OUT STATIC CONFIGURATION P NC NC A8 F9 A9 F10 A11 F12 G F0 A10 F11 E1 F0 DQ7 DQ6 DQ5 DQ4 DQ3 LOAD LOAD LOAD LOAD LOAD LOAD: 10kΩ VSS = GND VSS = GND VDD VDD/2 DYNAMIC CONFIGURATION NOTES: NOTES: 1. Power Supply: VDD = 5.5V (Min) 2. Resistors = 10kΩ ± 10% 3. 4. 5. 6. 7. 8. Power Supply: VDD = 5.5V (Min) VIH = VDD to VDD-1.0V VIL = 0.0V to 0.8V Resistors = 10kΩ ± 10% F0 = 100KHz ± 10%, 50% Duty Cycle F1 = F0/2; F2 = F1/2; F3 = F2/2; F4 = F3/2; F5 = F4/2; . . . F13 = F12/2 Irradiation Circuit HS1-6664RH 28 LEAD (8K X 8 PROM DIP) VDD NC NC 1 A12 2 A7 3 A6 4 A5 5 A4 6 A3 7 A2 8 A1 9 A0 10 DQ0 11 DQ1 12 DQ2 13 VSS 14 VDD = GND NOTES: 9. Power Supply: VDD = 5.5V ±0.5V 10. All Resistors = 47kΩ ± 10% 3 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VDD P NC NC A8 A9 A11 G A10 E1 DQ7 DQ6 DQ5 DQ4 DQ3 HS-6664RH Die Characteristics DIE DIMENSIONS: ASSEMBLY RELATED INFORMATION: 271mils x 307mils x 19mils ±1mils Substrate Potential: INTERFACE MATERIALS: VDD ADDITIONAL INFORMATION: Glassivation: Type: SiO2 Thickness: 8kÅ ± 1kÅ Worst Case Current Density: 2 x 105 A/cm2 Top Metallization: Transistor Count: M1:6kÅ ±1kÅ Si/Al/Cu 2kÅ ±500Å TiW M2:10kÅ ± 2kÅSi/Al/Cu 110, 874 Metallization Mask Layout 4 VDD VSS (23) A11 (24) A9 (22) G A10 (21) E (20) DQ7 (19) (26) NC (25) A8 DQ6 (18) DQ5 (17) (27) P (28) VDD DQ4 (16) DQ3 (15) GND (14) (3) A7 (4) A6 (2) A12 DQ2 (13) DQ1 (12) (5) A5 DQ0 (11) (6) A4 A0 (10) A1 (9) A2 (8) VDD VSS (7) A3 HS-6664RH HS-6664RH All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 5 ASIA Intersil Ltd. 8F-2, 96, Sec. 1, Chien-kuo North, Taipei, Taiwan 104 Republic of China TEL: 886-2-2515-8508 FAX: 886-2-2515-8369