INTERSIL HS1-5104ARH-T

HS-5104ARH-T
Data Sheet
July 1999
Radiation Hardened Low Noise Quad
Operational Amplifier
Intersil‘s Satellite Applications FlowTM (SAF) devices are
fully tested and guaranteed to 100kRAD total dose. These
QML Class T devices are processed to a standard flow
intended to meet the cost and shorter lead-time needs of
large volume satellite manufacturers, while maintaining a
high level of reliability.
The HS-5104ARH-T is a radiation hardened, monolithic
quad operational amplifier that provides highly reliable
performance in harsh radiation environments. Its excellent
noise characteristics coupled with a unique array of dynamic
specifications make this amplifier well-suited for a variety of
satellite system applications. Dielectrically isolated, bipolar
processing makes this device immune to Single Event
Latch-up.
File Number
4606.1
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose (γ) 1 x 105 RAD(Si)
- No Latch-Up, Dielectrically Isolated Device Islands
• Low Noise
- At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . 4.3nV/√Hz (Typ)
- At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . 0.6pA/√Hz (Typ)
• Low Offset Voltage . . . . . . . . . . . . . . . . . . . . 3.0mV (Max)
• High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 2.0V/µs (Typ)
• Gain Bandwidth Product . . . . . . . . . . . . . . . 8.0MHz (Typ)
Pinouts
HS1-5104ARH-T (SBDIP), CDIP2-T14
TOP VIEW
The HS-5104ARH-T shows almost no change in offset
voltage after exposure to 100K RAD(Si) gamma radiation,
with only a minor increase in current. Complementing these
specifications is a post radiation open loop gain in excess of
40K.
This quad operational amplifier is available in an industry
standard pinout, allowing for immediate interchangeability
with most other quad operational amplifiers.
Specifications
OUT 1
1
14 OUT 4
-IN1
2
13 -IN4
+IN1
3
12 +IN4
V+
4
11 V-
+IN2
5
10 +IN3
-IN2
6
9
-IN3
OUT 2
7
8
OUT 3
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-5104ARH-T
are contained in SMD 5962-95690. A “hot-link” is provided
from our website for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Intersil‘s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
www.intersil.com/quality/manuals.asp
Ordering Information
ORDERING
NUMBER
PART
NUMBER
HS9-5104ARH-T (FLATPACK), CDFP3-F14
TOP VIEW
OUT 1
1
14
OUT 4
-IN1
2
13
-IN4
+IN1
3
12
+IN4
V+
4
11
V-
+IN2
5
10
+IN3
-IN2
6
9
-IN3
OUT 2
7
8
OUT 3
TEMP.
RANGE
(oC)
5962R9569001TCC
HS1-5104ARH-T
-55 to 125
HS1-5104ARH/Proto
HS1-5104ARH/Proto
-55 to 125
5962R9569001TXC
HS9-5104ARH-T
-55 to 125
HS9-5104ARH/Proto
HS9-5104ARH/Proto
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.
HS-5104ARH-T
Die Characteristics
DIE DIMENSIONS:
PASSIVATION:
(2420µm x 2530µm x 483µm ±25.4µm)
Type: Nitride (Si3N4) over Silox (SiO2)
95 x 99 x 19mils ±1mil
Nitride Thickness: 3.5kÅ ±1.5kÅ
Silox Thickness: 12.0kÅ ±2kÅ
METALLIZATION:
WORST CASE CURRENT DENSITY:
Type: Al Si Cu
< 2.0e5 A/cm2
Thickness: 16.0kÅ ±2kÅ
SUBSTRATE POTENTIAL:
TRANSISTOR COUNT:
Unbiased (DI)
175
BACKSIDE FINISH:
PROCESS:
Silicon
Bipolar DI
Metallization Mask Layout
HS-5104ARH-T
+IN2
V+
+IN1
-IN1
-IN2
OUT2
OUT1
OUT3
OUT4
-IN3
-IN4
+IN3
V-
+IN4
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
2