50A02CH Bipolar Transistor −50V, −0.5A, Low VCE(sat), PNP Single www.onsemi.com Features • High Collector Current Capability • Low Collector to Emitter Saturation Voltage (Resistance): RCE(sat) typ=210mΩ [IC=0.5A, IB=50mA] • Low ON-Resistance (Ron) • Pb-Free, Halogen Free and RoHS compliance ELECTRICAL CONNECTION 3 1 : Base 2 : Emitter 3 : Collector 1 Typical Applications • Low-Frequency Amplifier • High Speed Switching • Small Motor Drive • Muting Circuit 2 MARKING © Semiconductor Components Industries, LLC, 2016 April 2016 - Rev. 2 1 1 2 CPH3 LOT No. Parameter Symbol Value Unit Collector to Base Voltage VCBO −50 V Collector to Emitter Voltage VCEO −50 V Emitter to Base Voltage VEBO −5 V Collector Current IC −500 mA Collector Current (Pulse) ICP −1.0 A Collector Dissipation (Note 2) PC 700 mW Junction Temperature Tj 150 °C Storage Temperature Tstg −55 to +150 °C Note 1 : Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 2 Note 2 : Surface mounted on ceramic substrate(600mm × 0.8mm) AX 3 SPECIFICATIONS ABSOLUTE MAXIMUM RATING at Ta = 25°C (Note 1, 2) ORDERING INFORMATION See detailed ordering and shipping information on page 5 of this data sheet. Publication Order Number : 50A02CH/D 50A02CH ELECTRICAL CHARACTERISTICS at Ta = 25°C (Note 3) Parameter Symbol Conditions Value min typ max Unit Collector Cutoff Current ICBO VCB=−40V, IE=0A −100 nA Emitter Cutoff Current IEBO VEB=−4V, IC=0A −100 nA DC Current Gain hFE fT VCE=−2V, IC=−10mA Gain-Bandwidth Product VCE=−10V, IC=−50mA 690 MHz Output Capacitance Cob VCB=−10V, f=1MHz 3.8 pF Collector to Emitter Saturation Voltage VCE(sat) IC=−100mA, IB=−10mA −60 −120 mV Base to Emitter Saturation Voltage VBE(sat) IC=−100mA, IB=−10mA −0.9 −1.2 V V(BR)CBO IC=−10μA, IE=0A −50 V V(BR)CEO IC=−1mA, RBE=∞ −50 V Emitter to Base Breakdown Voltage V(BR)EBO IE=−10μA, IC=0A −5 Turn-On Time ton tstg Collector to Base Breakdown Voltage Collector to Emitter Breakdown Voltage Storage Time See specified Test Circuit 200 500 V 30 ns 170 ns Fall Time 30 tf ns Note 3 : Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Switching Time Test Circuit www.onsemi.com 2 50A02CH www.onsemi.com 3 50A02CH www.onsemi.com 4 50A02CH PACKAGE DIMENSIONS unit : mm CPH3 CASE 318BA ISSUE O 1 : Base 2 : Emitter Recommended Soldering Footprint 3 : Collector 2.4 1.4 0.6 0.95 0.95 ORDERING INFORMATION Device Marking Package CPH3 (Pb-Free) 50A02CH-TL-E AX 50A02CH-TL-H CPH3 (Pb-Free / Halogen Free) Shipping (Qty / Packing) 3,000 / Tape & Reel † For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://www.onsemi.com/pub_link/Collateral/BRD8011-D.PDF ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf . SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. www.onsemi.com 5