NLAS3157, NLAS3257 Low Voltage SPDT Mux / Demux Analog Switch The NLAS3157 Mux / Demux Analog Switch is an advanced high− speed single−pole double−throw (SPDT) CMOS switch. It can be used as an analog switch or as a low−delay bus switch. Break−before−make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. The control input, S, is independent of supply voltage line switch in an ultra−small footprint. www.onsemi.com MARKING DIAGRAMS Features High Speed: tPD = 0.25 ns (Max) @ VCC = 4.5 V RON: 8.5 W Typ @ VCC = 4.2 V CON: 7.5 pF Typ @ VCC = 3.3 V VCC Range: 1.65 V to 4.5 V Ultra−Small 1 x 1 mm Package This Device is Pb−Free, Halogen Free/BFR Free and RoHS Compliant • Mobile Phones, PDAs, Camera 1 6 B1 S B1 2 5 GND A 3 4 B0 Y M 1 6 XLLGA6 1.0 x 1.0 CASE 713AD 2 5 VCC B0 3 4 A = Specific Device Code = Date Code Input S Function L H A = B0 A = B1 ORDERING INFORMATION Figure 2. XLLGA6 (NLAS3257) (Top View) A LM FUNCTION TABLE S GND Figure 1. ULLGA6 (NLAS3157) (Top View) M = Specific Device Code = Date Code L M Typical Applications VCC ULLGA6 1.0 x 1.0 CASE 613AD Y • • • • • • See detailed ordering and shipping information on page 5 of this data sheet. B0 B1 S Figure 3. Logic Diagram © Semiconductor Components Industries, LLC, 2016 April, 2016 − Rev. 1 1 Publication Order Number: NLAS3157/D NLAS3157, NLAS3257 Table 1. MAXIMUM RATINGS Symbol Parameter Value Unit VCC DC Supply Voltage −0.5 to +5.5 V VIN Control Input Voltage (S Pin) −0.5 to +5.5 V VIS Switch Input / Output Voltage (A, BO, B1 Pins) −0.5 to VCC + 0.5 V VIN < GND −50 mA VI/O < GND or VI/O > VCC ±50 mA IIK Control DC Input Diode Current (S Pin) IOK Switch I/O Port DC Diode Current (A, BO, B1 Pins) IO On−State Switch Current ±128 mA Continuous Current Through VCC or GND ±150 mA ICC DC Supply Current per Supply Pin ±150 mA IGND DC Ground Current per Ground Pin ±150 mA TSTG Storage Temperature Range −65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C qJA Thermal Resistance (Note 1) 407 °C/W PD Power Dissipation in Still Air at 85°C (Note 1) 1.5 mW MSL Moisture Sensitivity FR Flammability Rating VESD ILATCHUP Level 1 Oxygen Index: 28 to 34 ESD Withstand Voltage UL 94 V−0 @ 0.125 in Human Body Mode (Note 2) Machine Mode (Note 3) Charged Device Mode (Note 4) Latchup Performance Above VCC and Below GND at 85°C (Note 5) >8000 >300 >2000 V ±100 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA/ JESD22−A114−A 3. Tested to EIA/ JESD22−A115−A 4. Tested to JESD22−C101−A 5. Tested to EIA / JESD78 Table 2. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit VCC Positive DC Supply Voltage 1.65 4.5 V VI Control Input Voltage (S Pin) 0 4.5 V VIS Switch Input / Output Voltage (A, BO, B1 Pins) 0 VCC V TA Operating Free−Air Temperature −40 +85 °C Dt / DV Input Transition Rise or Fall Rate 0 0 5 DC ns/V Control Input Switch I/O Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. www.onsemi.com 2 NLAS3157, NLAS3257 Table 3. DC ELECTRICAL CHARACTERISTICS (Typical: T = 25°C, VCC = 3.3 V) −40°C to +85°C Symbol Parameter Test Conditions VCC (V) Min 0.75 1.25 1.52 1.94 Typ Max Unit VIH Control Input, HIGH Voltage 1.65 2.7 3.3 4.2 V VIL Control Input, LOW Voltage 1.65 2.7 3.3 4.2 0.25 0.4 0.4 0.5 V IIN Control Input, Leakage Current 0 ≤ VIS ≤ VCC 1.65 − 4.5 ±1.0 mA ICC Quiescent Supply Current VIS = VCC or GND; ID = 0 A 1.65 − 4.5 1.0 mA INC (OFF) INO (OFF) NC or NO Leakage Current VIS = 1.65 V to 4.5 V 4.5 ±10 ±100 nA ICOM (ON) COM ON Leakage Current VIS = 1.65 V to 4.5 V 4.5 ±10 ±100 nA Peak On−Resistance ION = 8 mA VIS = 0 V to VCC 1.65 2.7 3.3 4.2 15.4 10.8 9.5 8.5 23.2 12.4 11.0 9.9 W RFLAT On−Resistance Flatness ION = 8 mA VIS = 0 V to VCC 1.65 2.7 3.3 4.2 5.5 2.9 2.7 2.8 10.2 3.3 3.3 3.3 W DRON Delta On−Resistance ION = 8 mA VIS = 0 V to VCC 1.65 2.7 3.3 4.2 0.3 0.3 0.3 0.3 0.35 0.35 0.35 0.35 W ON RESISTANCE (Typical: T = 255C) RON Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Table 4. AC ELECTRICAL CHARACTERISTICS −405C to +855C Symbol Parameter Test Conditions VCC (V) Min Typ Max Unit 0.25 ns TIMING/FREQUENCY (Typical: T = 255C, VCC = 3.3 V, RL = 50 W, CL = 35 pF, f = 1 MHz) tPD Propagation Delay, A to Bn or Bn to A (See Figures 4 and 5) 1.65 − 4.5 tON Turn−ON Time (See Figures 7 and 8) 1.65 − 4.5 3.1 13.0 30.0 ns tOFF Turn−OFF Time (See Figures 7 and 8) 1.65 − 4.5 3.4 12.0 25.0 ns TBBM Break−Before−Make Time (See Figure 6) 1.65 − 4.5 2.0 −3 dB Bandwidth CL = 5 pF 1.65 − 4.5 1000 MHz BW ns ISOLATION (Typical: T = 255C, VCC = 3.3 V, RL = 50 W, CL = 5 pF) OIRR OFF−Isolation f = 240 MHz (See Figure 9) 1.65 − 4.5 -21 dB XTALK Non−Adjacent Channel Crosstalk f = 240 MHz 1.65 − 4.5 -21 dB www.onsemi.com 3 NLAS3157, NLAS3257 Table 4. AC ELECTRICAL CHARACTERISTICS CAPACITANCE (Typical: T = 255C) CIN Control Pin Input Capacitance VCC = 0 V, f = 1 MHz 1.5 VCC = 0 V, f = 10 MHz 1.0 CON ON Capacitance VCC = 3.3 V; OE = 0 V, S = 0 V or 3.3 V, f = 1 MHz 7.5 VCC = 3.3 V; OE = 0 V, S = 0 V or 3.3 V, f = 10 MHz 6.5 COFF OFF Capacitance VCC = VIS = 3.3 V; OE = 0 V, S = 3.3 V or 0 V, f = 1 MHz 3.8 VCC = VIS = 3.3 V; OE = 0 V, S = 3.3 V or 0 V, f = 10 MHz 2.0 VCC Input A 50% 50% GND tPLH tPHL VOH Output Y 50% VCC VOL Figure 4. Propagation Delay Waveforms VCC PULSE GENERATOR DUT RT CL RT = ZOUT of pulse generator (typically 50 W) Figure 5. Propagation Delay Test Circuit Figure 6. tBBM (Time Break−Before−Make) www.onsemi.com 4 RL pF NLAS3157, NLAS3257 Figure 7. tON / tOFF Figure 8. tON / tOFF Figure 9. Off Channel Isolation / On Channel Loss (BW)/Crosstalk (On Channel to Off Channel) / VONL ORDERING INFORMATION Package Shipping† NLAS3157MX3TCG ULLGA6 − 1.0 x 1.0, 0.35P (Pb−Free) 3000 / Tape & Reel NLAS3257MX3TCG XLLGA6 − 1.0 x 1.0, 0.35P (Pb−Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 5 NLAS3157, NLAS3257 PACKAGE DIMENSIONS ULLGA6 1.0x1.0, 0.35P CASE 613AD ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 5X 0.48 e 5X L 6X 0.22 NOTE 4 3 1 L1 1.18 6 4 0.53 6X b 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE 0.05 C 0.35 PITCH DIMENSIONS: MILLIMETERS NOTE 3 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 6 NLAS3157, NLAS3257 PACKAGE DIMENSIONS XLLGA6 1.0x1.0, 0.35P CASE 713AD ISSUE O ÇÇ ÇÇ PIN ONE REFERENCE 0.05 C 2X 0.05 C 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994 . 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO THE PLATED TERMINALS AND IS MEASURED BETWEEN 0.15 AND 0.25 MM FROM THE TERMINAL TIPS. 4. COPLANARITY APPLIES TO ALL OF THE TERMINALS. A B D E DIM A A1 b D E e e2 L L1 TOP VIEW 0.05 C A 0.05 C A1 SIDE VIEW NOTE 4 SEATING PLANE C RECOMMENDED SOLDERING FOOTPRINT* 0.35 PITCH L1 e 6X 1 2 MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.17 0.23 1.00 BSC 1.00 BSC 0.35 BSC 0.60 BSC 0.27 0.33 0.05 REF L 5X 0.50 3 PACKAGE OUTLINE e2 6 5 4 6X BOTTOM VIEW 1.25 1 0.55 b 0.07 M C A B 0.05 M C 6X 0.22 DIMENSIONS: MILLIMETERS NOTE 3 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLAS3157/D