NLAS323 D

NLAS323
Dual SPST Analog Switch,
Low Voltage, Single Supply
The NLAS323 is a dual SPST (Single Pole, Single Throw) switch,
similar to 1/2 a standard 4066. The device permits the independent
selection of 2 analog/digital signals. Available in the US8 package.
The use of advanced 0.6 micron CMOS process, improves the RON
resistance considerably compared to older higher voltage
technologies.
www.onsemi.com
MARKING
DIAGRAM
Features
•
•
•
•
•
•
•
•
•
•
•
On Resistance is 20 Typical at 5.0 V
Matching is < 1.0 Between Sections
2.0 to 6.0 V Operating Range
Ultra Low < 5.0 pC Charge Injection
Ultra Low Leakage < 1.0 nA at 5.0 V, 25 C
Wide Bandwidth > 200 MHz, −3.0 dB
2000 V ESD (Human Body Model)
Ron Flatness $6.0 at 5.0 V
US8 Package
Independent, Positive Enable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
NO1
1
8
VCC
COM1
2
7
IN1
IN2
3
6
COM2
GND
4
5
NO2
8
US8
US SUFFIX
CASE 493
8
1
A4 MG
G
1
A4
M
G
= Specific Device Code
= Date Code
= Pb−Free Package
(Note: Microdot may be in either location)
PIN ASSIGNMENT
1
NO1
2
COM1
3
IN2
4
GND
5
NO2
6
COM2
7
IN1
8
VCC
FUNCTION TABLE
On/Off
Enable Input
State of
Analog Switch
L
H
Off
On
Figure 1. Pinout
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
July, 2015 − Rev. 7
1
Publication Order Number:
NLAS323/D
NLAS323
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VCC
DC Supply Voltage
*0.5 to )7.0
V
VI
DC Input Voltage
*0.5 to )7.0
V
VO
DC Output Voltage
*0.5 to )7.0
V
IIK
DC Input Diode Current
VI < GND
*50
mA
IOK
DC Output Diode Current
VO < GND
*50
mA
IO
DC Output Sink Current
$50
mA
ICC
DC Supply Current per Supply Pin
$100
mA
IGND
DC Ground Current per Ground Pin
$100
mA
TSTG
Storage Temperature Range
*65 to )150
°C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
TJ
Junction Temperature under Bias
JA
Thermal Resistance
PD
Power Dissipation in Still Air at 85°C
MSL
Moisture Sensitivity
FR
Flammability Rating
VESD
ESD Withstand Voltage
(Note 1)
260
°C
)150
°C
250
°C/W
250
mW
Level 1
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
Human Body Model (Note 2)
Machine Model (Note 3)
Charged Device Model (Note 4)
> 2000
> 150
N/A
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2−ounce copper trace with no air flow.
2. Tested to EIA/JESD22−A114−A.
3. Tested to EIA/JESD22−A115−A.
4. Tested to JESD22−C101−A.
RECOMMENDED OPERATING CONDITIONS
Symbol
Characteristics
Min
Max
Unit
2.0
5.5
V
VCC
Positive DC Supply Voltage
VIN
Digital Input Voltage (Enable)
GND
5.5
V
VIO
Static or Dynamic Voltage Across an Off Switch
GND
VCC
V
VIS
Analog Input Voltage (NO, COM)
GND
VCC
V
TA
Operating Temperature Range, All Package Types
−55
+125
°C
tr, tf
Input Rise or Fall Time,
(Enable Input)
0
0
100
20
ns/V
Vcc = 3.3 V + 0.3 V
Vcc = 5.0 V + 0.5 V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
90
419,300
47.9
100
178,700
20.4
110
79,600
9.4
120
37,000
4.2
130
17,800
2.0
140
8,900
1.0
TJ = 80°C
117.8
TJ = 90°C
1,032,200
TJ = 100°C
80
TJ = 110°C
Time, Years
TJ = 120°C
Time, Hours
FAILURE RATE OF PLASTIC = CERAMIC
UNTIL INTERMETALLICS OCCUR
TJ = 130°C
Junction
Temperature 5C
NORMALIZED FAILURE RATE
DEVICE JUNCTION TEMPERATURE VERSUS TIME
TO 0.1% BOND FAILURES
1
1
10
100
1000
TIME, YEARS
Figure 2. Failure Rate vs. Time Junction Temperature
www.onsemi.com
2
NLAS323
DC CHARACTERISTICS − Digital Section (Voltages Referenced to GND)
Guaranteed Max Limit
Symbol
Parameter
Condition
VCC
−55 to 255C
<855C
<1255C
Unit
VIH
Minimum High−Level Input
Voltage, Enable Inputs
2.0
3.0
4.5
5.5
1.5
2.1
3.15
3.85
1.5
2.1
3.15
3.85
1.5
2.1
3.15
3.85
V
VIL
Maximum Low−Level Input
Voltage, Enable Inputs
2.0
3.0
4.5
5.5
0.5
0.9
1.35
1.65
0.5
0.9
1.35
1.65
0.5
0.9
1.35
1.65
V
IIN
Maximum Input Leakage
Current, Enable Inputs
VIN = 5.5 V or GND
0 V to 5.5 V
+0.1
+1.0
+1.0
A
ICC
Maximum Quiescent Supply Current (per package)
Enable and VIS = VCC or
GND
5.5
1.0
1.0
2.0
A
DC ELECTRICAL CHARACTERISTICS − Analog Section
Guaranteed Max Limit
Symbol
Parameter
Condition
VCC
−55 to 255C
<855C
<1255C
Unit
RON
Maximum On Resistance
(Figures 8 − 12)
VIN = VIH
VIS = VCC to GND
IIsI = <10.0mA
3.0
4.5
5.5
45
30
25
50
35
30
55
40
35
RFLAT(ON)
On Resistance Flatness
VIN = VIH
IIsI = <10.0 mA
VIS = 1 V, 2 V, 3.5 V
4.5
4.0
4.0
5.0
INO(OFF)
Off Leakage Current, Pin 2
(Figure 3)
5.5
1.0
10
100
nA
ICOM(OFF)
Off Leakage Current, Pin 1
(Figure 3)
5.5
1.0
10
100
nA
VIN = VIL
VNO = 1.0 V, VCOM = 4.5 V or
VCOM = 1.0 V and VNO 4.5 V
VIN = VIL
VNO = 4.5 V or 1.0 V
VCOM = 1.0 V or 4.5 V
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns)
Guaranteed Max Limit
VCC
Symbol
Parameter
Test Conditions
(V)
−55 to 255C
Min
<855C
Typ
Max
Min
Typ
<1255C
Max
Min
Typ
Max
Unit
tON
Turn−On Time
RL = 300 CL = 35 pF
(Figures 4, 5, and 13)
2.0
3.0
4.5
5.5
7.0
5.0
4.5
4.5
14
10
9.0
9.0
16
12
11
11
16
12
11
11
ns
tOFF
Turn−Off Time
RL = 300 CL = 35 pF
(Figures 4, 5, and 13)
2.0
3.0
4.5
5.5
11.0
7.0
5.0
5.0
22
14
10
10
24
16
12
12
24
16
12
12
ns
Typical @ 25, VCC = 5.0 V
CIN
CNO or CNC
CCOM(OFF)
CCOM(ON)
Maximum Input Capacitance, Select Input
Analog I/O (switch off)
Common I/O (switch off)
Feedthrough (switch on)
8.0
10
10
20
www.onsemi.com
3
pF
NLAS323
ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted)
Symbol
Parameter
Condition
VCC
Limit
V
25°C
Unit
BW
Maximum On−Channel −3dB Bandwidth
or Minimum Frequency Response
VIS = 0 dBm
VIS centered between VCC and GND
(Figures 6 and 14)
3.0
4.5
5.5
190
200
220
MHz
VONL
Maximum Feedthrough On Loss
VIS = 0 dBm @ 10 kHz
VIS centered between VCC and GND
(Figure 6)
3.0
4.5
5.5
−2
−2
−2
dB
VISO
Off−Channel Isolation
f = 100 kHz; VIS = 1.0 V RMS
VIS centered between VCC and GND
(Figures 6 and 15)
3.0
4.5
5.5
−93
dB
Q
Charge Injection
Enable Input to Common I/O
VIS = VCC to GND, FIS = 20 kHz
tr = tf = 3.0 ns
RIS = 0 , CL = 1000 pF
Q = CL * VOUT
(Figures 6 and 16)
3.0
5.5
1.5
3.0
pC
Total Harmonic Distortion
THD + Noise
FIS = 20 Hz to 1 MHz, RL = Rgen = 600 , CL = 50 pF
VIS = 3.0 VPP sine wave
VIS = 5.0 VPP sine wave
(Figure 17)
3.3
5.5
0.3
0.15
1.00E+05
1.00E+04
1.00E+03
1.00E+02
LEAKAGE (pA)
THD
1.00E+01
1.00E+00
ICOM(ON)
1.00E−01
1.00E−02
1.00E−03
ICOM(OFF)
1.00E−04
1.00E−05
1.00E−06
INO(OFF)
1.00E−07
−55 −35 −15
5
25
45
65
85
105 125 145
TEMPERATURE (°C)
Figure 3. Switch Leakage vs. Temperature
www.onsemi.com
4
%
NLAS323
VCC
DUT
VCC
Input
NO
50%
50%
0V
COM
VOUT
0.1 F
300 VOH
35 pF
90%
90%
Output
VOL
Input
tON
tOFF
Figure 4. tON/tOFF
VCC
VCC
Input
DUT
300 NO
COM
50%
50%
0V
VOUT
VOH
35 pF
Output
10%
10%
VOL
Input
tOFF
Figure 5. tON/tOFF
www.onsemi.com
5
tON
NLAS323
DUT
Reference
COM
Transmitted
NO
50 Generator
50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is
the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction.
ǒVVOUT
Ǔ for VIN at 100 kHz
IN
VOUT
Ǔ for VIN at 100 kHz to 50 MHz
VONL = On Channel Loss = 20 Log ǒ
VIN
VISO = Off Channel Isolation = 20 Log
Bandwidth (BW) = the frequency 3.0 dB below VONL
Figure 6. Off Channel Isolation/On Channel Loss (BW)/Crosstalk
(On Channel to Off Channel)/VONL
DUT
NO
VCC
VIN
COM
GND
CL
Output
Off
VIN
Figure 7. Charge Injection: (Q)
www.onsemi.com
6
On
Off
VOUT
NLAS323
80
80
70
70
60
VCC = 2.0
50
50
RON ()
RON ()
60
40
VCC = 2.5
30
−55°C
30
25°C
VCC = 3.0
20
40
20
85°C
VCC = 4.5
10
10
0
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
125°C
0
5
0.2
0.4
0.6
0.8
1
1.2 1.4
1.6
1.8
VCOM (VOLTS)
VIS (VOLTS)
Figure 8. RON vs. VCOM and VCC (@255C)
Figure 9. RON vs. VCOM and Temperature,
VCC = 2.0 V
45
2
30
40
20
25
RON ()
RON ()
30
−55°C
20
25°C
15
10
15
125°C
25°C
85°C
10
85°C
5
125°C
5
0
−55°C
25
35
0
0.2 0.4 0.6 0.8 1
1.2 1.4 1.6 1.8
2
0
2.2 2.4
0
0.3
0.6
0.9
1.2 1.5
1.8
2.1
2.4
2.7
VCOM (VOLTS)
VCOM (VOLTS)
Figure 10. RON vs. VCOM and Temperature,
VCC = 2.5 V
Figure 11. RON vs. VCOM and Temperature,
VCC = 3.0 V
3
35.0
18
30.0
16
−55°C
25°C
25.0
12
TIME (nS)
RON ()
14
85°C
10
8
15.0
4
5.0
2
0.0
2.0
0
tON
10.0
125°C
6
20.0
tOFF
0
0.4 0.8 1.2 1.6
2
2.4 2.8 3.2 3.6
4
4.4
3.0
4.5
5.0
5.5
VCC (V)
VCOM (VOLTS)
Figure 12. RON vs. VCOM and Temperature,
VCC = 4.5 V
Figure 13. Switching Time vs. Supply Voltage,
T = 255C
www.onsemi.com
7
NLAS323
0
0
0
BANDWIDTH (dB/Div)
Phase (Degrees)
5
VCC = 5.0 V
TA = 25°C
0.01
0.1
1
10
OFF ISOLATION (dB/Div)
10
PHASE (Degrees)
Bandwidth (On − Loss)
−50
VCC = 5.0 V
TA = 25°C
−100
100 300
0.01
0.1
FREQUENCY (MHz)
1
100 300
10
FREQUENCY (MHz)
Figure 14. ON Channel Bandwidth and Phase
Shift Over Frequency
Figure 15. Off Channel Isolation
100
1.60
1.40
VCC = 5.0 V
1.20
10
0.80
THD (%)
Q (pC)
1.00
VCC = 3.0 V
1
3.3 V
0.60
0.40
0.1
5.5 V
0.20
0.00
0.0
0.01
1.0
2.0
3.6
3.0
VCOM (V)
4.0
4.5
10
5.0
100
1000
10000
100000 1000000
FREQUENCY (Hz)
Figure 16. Charge Injection vs. VCOM
Figure 17. THD vs. Frequency
DEVICE ORDERING INFORMATION
Device
Order Number
NLAS323USG
Package
Shipping†
US8
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
8
NLAS323
PACKAGE DIMENSIONS
US8
US SUFFIX
CASE 493−02
ISSUE D
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSION OR GATE BURR. MOLD
FLASH. PROTRUSION AND GATE BURR SHALL
NOT EXCEED 0.14MM (0.0055”) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH
AND PROTRUSION SHALL NOT EXCEED 0.14MM
(0.0055”) PER SIDE.
5. LEAD FINISH IS SOLDER PLATING WITH
THICKNESS OF 0.0076−0.0203MM (0.003−0.008”).
6. ALL TOLERANCE UNLESS OTHERWISE
SPECIFIED ±0.0508MM (0.0002”).
X Y
A
8
J
5
DETAIL E
B
L
1
4
R
S
G
P
U
C
SEATING
PLANE
T
D
0.10 (0.004)
H
0.10 (0.004) T
K
M
N
R 0.10 TYP
T X Y
V
M
F
DIM
A
B
C
D
F
G
H
J
K
L
M
N
P
R
S
U
V
MILLIMETERS
MIN
MAX
1.90
2.10
2.20
2.40
0.60
0.90
0.17
0.25
0.20
0.35
0.50 BSC
0.40 REF
0.10
0.18
0.00
0.10
3.00
3.20
0_
6_
0_
10 _
0.23
0.34
0.23
0.33
0.37
0.47
0.60
0.80
0.12 BSC
INCHES
MIN
MAX
0.075
0.083
0.087
0.094
0.024
0.035
0.007
0.010
0.008
0.014
0.020 BSC
0.016 REF
0.004
0.007
0.000
0.004
0.118
0.128
0_
6_
0_
10 _
0.010
0.013
0.009
0.013
0.015
0.019
0.024
0.031
0.005 BSC
DETAIL E
RECOMMENDED
SOLDERING FOOTPRINT*
8X
0.30
8X
0.68
3.40
1
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NLAS323/D