NCS5652 D

NCS5652, NCV5652
Dual Power Operational
Amplifier
Description
The NCx5652 is a dual power operational amplifier with a versatile
output stage configuration that allows conventional op−amp biasing or
user tuning of efficiency, isolation, or current monitoring. Integrated
flyback diodes protect the amplifiers during inductive load transients.
Operating at supply voltages as low as 3.3 V, the NCx5652 is capable
of delivering 500 mA of current while maintaining an excellent output
swing. The integrated thermal shutdown circuit protects the NCx5652
from excessive power dissipation. A thermal warning flag is provided
for external monitoring of the device, providing a flexible interface to
a system’s microcontroller. This open−collector thermal flag output
doubles as a DISABLE input that can be used to tri−state both
amplifier outputs under user control. The 12−pin UDFN 3x3 mm
package provides thermal robustness while achieving space savings
on high density PCBs.
www.onsemi.com
1
UDFN12
MU SUFFIX
CASE 517AM
MARKING DIAGRAM
Features
•
•
•
•
•
•
•
•
•
•
Operating Supply Voltage Range: 3.3 V to 13.2 V
Output Supply Voltage Range: 3.3 V to 13.2 V
High Current Drive: 500 mA Operating
Thermal Flag: Open−collector for Flexible Interface
Thermal Shutdown/ Disable Function
Output Short Circuit Tolerable (1 A to Source or Ground)
No Power Sequencing Required (VCC, VC1, VC2)
UDFN12 Package Features Wettable Flank for Improved
Solderability
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Typical Applications
•
•
•
•
•
Telecom
Vcom Driver
Small DC Brush Motors
LED String Driver
Electrochromic Driver
N5652
ALYWG
G
N5652 = Specific Device Code
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
IN1− 1
IN1+
2
−
+
DISABLE/Tflag 3
IN2+
4
IN2−
5
GND
6
+
−
EXPOSED
THERMAL PAD
(13)
12
GND
11
OUT1
10
VC1
9
VCC
8
VC2
7
OUT2
ORDERING INFORMATION
See detailed ordering and shipping information on page 12 of
this data sheet.
© Semiconductor Components Industries, LLC, 2015
June, 2015 − Rev. 1
1
Publication Order Number:
NCS5652/D
NCS5652, NCV5652
VCC
EN VCC
IN1−
IN1+
10 VC1
−
1
Class
AB
Bias
2
11 OUT1
+
VCC
9
EN
DISABLE/
Tflag
3
12 GND
Thermal
Detection
VCC
EN VCC
IN2+ 4
IN2−
VCC
+
−
5
Class
AB
Bias
6
GND
8
VC2
7
OUT2
Exposed
Pad (13)
Figure 1. Block Diagram
Table 1. PIN DESCRIPTION
Pin
Name
Type
1
IN1−
Input
Negative input of amplifier 1.
Description
Positive input of amplifier 1.
2
IN1+
Input
3
DISABLE/Tflag
Input/Output
4
IN2+
Input
Positive input of amplifier 2.
5
IN2−
Input
Negative input of amplifier 2.
Dual use pin −Thermal flag− an open collector output requiring an external
pull−up resistor. The output is pulled low when the thermal limit is reached. It
is high−impedance in normal operation.
Disable − Must use an open collector/drain for input with pull−up resistor to
Vcc. Pulling pin low disables the amplifiers. If pin is not used, a pull−up resistor to Vcc is still required (10 KW recommended)
6
GND
Power
Power ground.
7
OUT2
Output
Output of amplifier 2.
8
VC2
Power
Positive supply of output stage 2.
9
VCC
Power
Positive supply of core circuitry.
10
VC1
Power
Positive supply of output stage 1.
11
OUT1
Output
Output of amplifier 1.
12
GND
Power
Power ground.
13
EXPOSED PAD
Power
The Exposed Pad must be attached to a heat−sinking conduit and connected
to GND.
www.onsemi.com
2
NCS5652, NCV5652
Table 2. ABSOLUTE MAXIMUM RATINGS Over operating free−air temperature, unless otherwise stated
Symbol
Limit
Unit
VCC
16
V
VC1, VC2
16
V
Vid
±VCC
V
VICR
−0.3 to VCC +0.3
V
IOUT
±1000
mA
VDISABLE/Tflag
7
V
Storage Temperature
TSTG
−65 to 165
°C
Junction Temperature
TJ(MAX)
150
°C
Human Body Model
HBM
±1500 (IN−, Tflag pins).
±2000 (All other pins)
V
Machine Model
MM
±150( IN−, Tflag pins).
±200 (All other pins)
V
CDM
±2500
V
Parameter
Supply Voltage (VCC − GND)
Output Supply Voltage
INPUT AND OUTPUT PINS
Differential Input Voltage
Input Common Mode Voltage Range
Output Current (Note 1)
DISABLE/Tflag Pin Voltage (Note 2)
TEMPERATURE
ESD RATINGS (Note 3)
Charge Device Model
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Continuous short−to−ground or source; power dissipation must be taken into consideration.
2. Connected to voltage source via a pull−up resistor.
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (JEDEC standard: JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (JEDEC standard: JESD22−A115)
ESD Charged Device Model tested per ANSI/ESD S5.3.1−2009 (AEC−Q100−011)
Table 3. THERMAL INFORMATION (Note 4)
Thermal Metric
Symbol
Limit
Unit
Junction to Ambient – UDFN12
(Exposed pad connected to 50 mm2 one ounce copper.)
qJA
147
°C/W
Junction to Ambient – UDFN12
(Exposed pad connected to 1200 mm2 one ounce copper.)
qJA
52
°C/W
Symbol
Limit
Unit
VCC
3.3 to 13.2
V
Output Supply Voltage
VC1, VC2
3.3 to 13.2
V
Output Current (Note 5)
IC1, IC2
±500
mA
TA
−40 to +125
°C
4. Based on JEDEC.
Table 4. RECOMMENDED OPERATING CONDITIONS
Parameter
Operating Supply Voltage
Operating Temperature Range
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
5. Power dissipation must be taken into consideration to avoid thermal shutdown.
www.onsemi.com
3
NCS5652, NCV5652
Table 5. ELECTRICAL CHARACTERISTICS: VCC = VC1 = VC2 = 5 V
Boldface limits apply over the specified temperature range, TA = –40°C to +125°C.
At TA = +25°C, RL = 1 kW connected to midsupply, VOUT = midsupply, unless otherwise noted.
Typ
Max
Unit
VOS
1
15
mV
dV/dT
2
Input Bias Current
IIB
550
1000
nA
Input Offset Current
IOS
10
100
nA
3.8
V
Parameter
Symbol
Conditions
Min
INPUT CHARACTERISTICS
Offset Voltage
Offset Voltage Drift
Input Common Mode Range (Note 6)
Common Mode Rejection Ratio
mV/°C
VCM
0
CMRR
90
100
dB
4.0
4.15
V
OUTPUT CHARACTERISTICS (OUT1, OUT2)
Output Voltage High (Note 7)
Output Voltage Low
VOH
Vid = 1 V, IO = +250 mA
VOL
Vid = −1 V, IO = −250 mA
200
350
mV
DYNAMIC PERFORMANCE
Open Loop Voltage Gain
AVOL
Gain Bandwidth Product
GBWP
Gain Margin
90
105
dB
RL = 47 W, CL = 100 nF
350
kHz
AM
RL = 47 W, CL = 100 nF
6
dB
Phase Margin
yM
RL = 47 W, CL = 100 nF
45
°
Slew Rate
SR
1.5
V/ms
75
dB
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
VCC = VC1 = VC2 = 3.3 V to 13.2 V
Quiescent Current (Operating)
ICC
No RL, CL = 100 nF
3
4
mA
IC1, IC2
(Per op amp) No RL, CL = 100 nF
4
6
mA
Quiescent Current (Output)
65
THERMAL CHARACTERISTICS
Thermal Shutdown (Note 8)
°C
160
TSHUTDOWN
LOGIC CHARACTERISTICS (DISABLE/Tflag)
Output Voltage Low (Note 6)
VOL
Input Voltage High (Note 9)
VIH
Input Voltage Low (Note 10)
VIL
IOL = 1 mA
0.7
1.5
V
V
1.1
V
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
6. VCM is a function of VCC (VCC – 1.2 V).
7. VOH is a function of VCC (VCC − 0.8 V).
8. Guaranteed by design/characterization.
9. DISABLE/Tflag pin with a pull−up resistor for sourcing.
10. DISABLE/Tflag pin with an open collector/drain for sinking.
www.onsemi.com
4
NCS5652, NCV5652
TYPICAL CHARACTERISTICS
3.4
12
−40°C
25°C
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
3.2
3
2.8
125°C
2.6
2.4
2.2
3
4
5
6
7
8
25°C
9
125°C
8
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 2. ICC Quiescent Current vs. Supply
Voltage over Temperature
Figure 3. Ic Quiescent Current vs. Supply
Voltage over Temperature (Ic1, Ic2 combined)
1.000
25
−40°C
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
−40°C
10
6
9 10 11 12 13 14 15 16 17
30
20
25°C
15
10
125°C
5
VCC = VC1 = VC2
Vid = −1 V
0.100
0.010
−40°C
25°C
0.001
125°C
VCC = VC1 = VC2
Vid = −1 V
0
0.0001
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 4. Comparator Mode (Negative), ICC
Quiescent Current vs Supply Voltage
Figure 5. Comparator Mode (Negative), Ic
Quiescent Current vs Supply Voltage (Ic1,Ic2
Combined)
3.0
12
−40°C
2.8
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
11
7
VCC = VC1 = VC2
VOUT = VCC/2
2
VCC = VC1 = VC2
VOUT = VCC/2
25°C
2.6
125°C
2.4
2.2
VCC = VC1 = VC2
Vid = +1 V
2.0
3
4
5
6
7
8
10
−40°C
8
25°C
6
125°C
4
2
VCC = VC1 = VC2
Vid = +1 V
0
9 10 11 12 13 14 15 16 17
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 6. Comparator Mode (Positive), ICC
Quiescent Current vs Supply Voltage
Figure 7. Comparator Mode (Positive), Ic
Quiescent Current vs Supply Voltage (Ic1,Ic2
Combined)
www.onsemi.com
5
NCS5652, NCV5652
OUTPUT VOLTAGE FROM POS RAIL (V)
TYPICAL CHARACTERISTICS
VOLTAGE FROM NEG RAIL (V)
10
−40°C
1
0°C
+125°C
+25°C
0.1
0.01
VCC = 3.3 to 13.2 V
VCC = VC1 = VC2
Vid = −1 V
0.001
0
100
200
300
400
500
600
+125°C
+25°C
0.6
0.8
−40°C
1.0
0°C
1.2
0
700
100
200
300
500
600
80
0
40
Gain
−50
−20
−40
100
10K
1K
100K
1M
10
10M
50
0
−50
−100
100
1K
−150
−200
−250
10K
100K
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 10. Open Loop Gain/Phase
(No RL, CL = 0)
Figure 11. Open Loop Gain/Phase
(No RL, CL = Varied)
250
Phase − CL = 50 nF
Phase − CL = 100 nF
Phase − CL = 200 nF
Phase − CL = 300 nF
200
150
100
Gain − CL = 50 nF
Gain − CL = 100 nF
Gain − CL = 200 nF
Gain − CL = 300 nF
0
−200
150
TA = 25°C
VOUT = VCC/2
VCC = VC1 = VC2 = 5 V
No RL
20
VCC = VC1 = VC2 = 5 V
VOUT = VCC/2
No RL, CL = 0
TA = 25°C
200
GAIN (dB)
120
1M
250
Phase − CL = 50 nF
Phase − CL = 100 nF
Phase − CL = 200 nF
Phase − CL = 300 nF
100
80
200
150
PHASE (Deg)
−50
−100
60
TA = 25°C
VOUT = VCC/2
VCC = VC1 = VC2 = 5 V
RL = 47 W
40
20
Gain − CL = 50 nF
Gain − CL = 100 nF
Gain − CL = 200 nF
Gain − CL = 300 nF
−150
−200
−250
10
100
1K
−20
−40
100K
10
1M
0
−50
−100
Gain − CL = 50 nF
Gain − CL = 100 nF
Gain − CL = 200 nF
Gain − CL = 300 nF
0
10K
50
TA = 25°C
VOUT = VCC/2
VCC = VC1 = VC2 = 5 V
RL = 150 W
100
1K
−150
−200
−250
10K
100K
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 12. Open Loop Gain/Phase
(RL = 47 W, CL = Varied)
Figure 13. Open Loop Gain/Phase
(RL = 150 W, CL = Varied)
www.onsemi.com
6
PHASE (Deg)
100
100
0
PHASE (Deg)
60
250
Phase − CL = 50 nF
Phase − CL = 100 nF
Phase − CL = 200 nF
Phase − CL = 300 nF
100
Phase
50
50
700
Figure 9. High Level Output Voltage vs. Output
Current Over Temperature
GAIN (dB)
120
10
400
Figure 8. Low Level Output Voltage vs. Output
Current Over Temperature
100
PHASE (Deg)
0.4
OUTPUT CURRENT (mA)
150
−150
VCC = 3.3 to 13.2 V
VCC = VC1 = VC2
Vid = +1 V
0.2
OUTPUT CURRENT (mA)
200
−100
0
1M
NCS5652, NCV5652
TYPICAL CHARACTERISTICS
25
GAIN MARGIN (dB)
20
15
No RL
RL =150 W
10
RL = 48 W
5
0
50
100
200
300
CL, CAPACITIVE LOAD (nF)
Figure 14. Gain Margin vs. Load
90
PHASE MARGIN (Deg)
80
70
60
50
No RL
40
RL = 150 W
30
RL = 48 W
20
10
0
50
100
200
CL, CAPACITIVE LOAD (nF)
300
Figure 15. Phase Margin vs. Load
0
CHANNEL SEPARATION (dB)
OUTPUT IMPEDANCE (W)
1000
100
10
1
−20
−40
−60
−80
−100
−120
0.1
10
100
1K
10K
100K
1M
10
100
1K
10K
100K
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 16. Open Loop Output Impedance vs.
Frequency
Figure 17. Channel Separation vs. Frequency
www.onsemi.com
7
NCS5652, NCV5652
TYPICAL CHARACTERISTICS
1
10
TA = 25°C
FIN = 1 KHz
AV = 1
VCC = VC1 = VC2 = 5 V
THD + N (%)
THD + N (%)
1
TA = 25°C
AV = 1
VCC = VC1 = VC2 = 5 V
0.1
0.1
0.01
0.01
0.001
0.001
0
1
2
3
4
5
10
6
100
10K
100K
VOUT pk−pk (V)
FREQUENCY (Hz)
Figure 18. Total Harmonic Distortion + Noise
vs. Vout
Figure 19. Total Harmonic Distortion + Noise
vs. Frequency
120
160
140
100
PSRR−
120
80
PSRR (dB)
CMRR (dB)
1K
60
TA = 25°C
VCC = VC1 = VC2 = 5 V
40
100
PSRR+
80
60
40
20
TA = 25°C
VCC = VC1 = VC2 = 5 V
20
0
0
10
100
1K
10K
100K
1M
10M
100M
10
100
1K
10K
100K
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 20. CMRR vs. Frequency
Figure 21. PSRR vs. Frequency
www.onsemi.com
8
10M
NCS5652, NCV5652
APPLICATIONS INFORMATION
high power applications. The maximum dissipation the
NCx5652 can handle is given by:
Figure 22 shows a typical application on how to connect
the NCx5652 pins where the VCC is supplied by 5 V and the
output stages are supplied with 12 V. In this configuration
the inputs can be driven up to 3.8 V. The outputs can be as
high as 4 V and able to go near ground due to the excellent
VOL parameters. The loads can be up to 500 mA continuous.
ƪT
P D(MAX) +
JǒMAXǓ
ƫ
* TA
R qJA
(eq. 1)
Since TJ is not recommended to exceed 150°C, then the
NCx5652 soldered on 1200 mm2, 1 oz copper area, FR4 can
dissipate up to 2.5 W when the ambient temperature (TA) is
25°C.
Power Supply
The supply pins should be properly bypassed with
ceramic 0.1 mF to 1 mF capacitors. The different supply pins
for the input stage (VCC) and the output stage (VC1,VC2)
provide a flexible power option. In many applications there
is often a digital supply and different supply for driving
motors or elements. The output stage can be optimized for
the voltage requirements of the load. There are no
requirements on the voltage levels (as long as they are within
specification) and sequencing of the VCC, VC1, and VC2
pins. It should be noted that the input and output swings are
a function of VCC. The common mode voltage range and
output swings are specified in the electrical section
according to the VCC voltage.
Output Short Circuit Protection
The NCx5652 is designed to withstand short circuits on
the outputs. With proper application design, the outputs can
be shorted to ground or to a source up to 16 V without
damage. Depending on the ambient temperature and thermal
conductivity of the PCB, the device may enter thermal
shutdown during a short circuit event. Even though the
thermal shutdown disables the outputs, the application
should not allow the outputs to be enabled continuously
during a short circuit event when a thermal shutdown occurs.
The DISABLE/Tflag pin (pin 3) should be monitored to
recognize when a thermal shutdown event happens. And
then respond within 5ms to disable the outputs for a
minimum of 5 seconds (DIS and DISHOLD parameters in
Figure 23). This low duty cycle keeps the device average
junction temperature in a safe zone.
Shutdown Feature
The NCx5652 provides a thermal shutdown feature to
protect the device during fault conditions (See Output Short
Circuit Protection section). Pin 3 is an open collector output
that can be connected to a microcontroller to alert the system
that a thermal shutdown has occurred. The thermal
shutdown circuit has approximately 20°C hysteresis. When
the device is in a thermal shutdown condition, the outputs
are tri−stated. The same pin can be used for an input as well.
It can be open collector OR’d so that the microcontroller can
disable the device by driving this pin low. This pin must
always be pulled high via a 10 kW resistor (recommended
value). It should always be driven with an open
collector/drain device. Some microcontrollers have open
drain configurable outputs.
• Output Short to Source
When it is possible that the NCx5652 can be shorted to a
source higher than VC1, VC2, a diode (D1) should be used
to prevent current flow going back to the VC1,VC2 source
as shown in Figure 22. The worst case for this event is when
VOUT is low (VOL). Figure 23 shows a diagram short from
low to high (VOUT = VOL shorted to 12 V−16 V). Note that
when the short circuit current (ISC) is low, the device is either
operating normal or the outputs are disabled (tri−stated).
Table 6 shows typical values for ISC−PK and ISC−CLAMP. The
parameter ISC−HOLD is the time it takes the device to enter
thermal shutdown. This parameter varies depending on the
ambient temperature and the thermal conductivity of the
PCB. If the device thermal limit is not reached, the output
current will stay clamped to the ISC−CLAMP value.
As stated earlier, the device should be disabled as soon as
thermal shutdown occurs (noted by TSHDN in figure 23).
After TSHDN occurs the device thermal shutdown circuit
will disable the outputs for approximately 20ms before
enabling them again (a characteristic from the thermal
shutdown hysteresis). To allow variations of conditions, it is
recommended that the microcontroller responds within 5ms
(DIS parameter in Table 6) to keep pin 3 low. After a
minimum of 5 seconds the microcontroller can then enable
the outputs (indicated by the EN in Figure 23). This cycle
will repeat until the short is removed from the outputs.
Figures 24 thru 26 show some typical values for an example
Stability
The NCx5652 is designed to drive large capacitive loads
and not oscillate even at unity gain. It is recommended that
a minimum of 0.1 mF capacitor be placed on the outputs to
ensure stability. This is mainly required for no load or light
load conditions. If configuring the device as a follower, it is
also recommended to use a 10 kW feedback resistor as
shown in Figure 22.
Thermal Considerations
As power in the NCx5652 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and the ambient temperature
affect the rate of junction temperature rise for the part. When
the NCS5652 has good thermal conductivity through the
PCB, the junction temperature will be relatively low with
www.onsemi.com
9
NCS5652, NCV5652
application using a 1200 mm2 one ounce copper PCB. The
microcontroller disables the outputs 1ms after detecting the
thermal shutdown. Note that at −40°C thermal shutdown
does not happen. Again the ISC−HOLD parameter will vary
with temperature and PCB characteristics.
It is possible that a short from low to high can disable the
outputs and not cause a thermal shutdown. When the short
is pulled significantly higher than VCC (8−9 V), the
high−side NPN protection circuit will be activated. This
protection circuitry will turn off the current source providing
the drive current to the output stage. This results in a very
short ISC−PK pulse and then disables the output. The output
is disabled until the short is removed.
maximum when shorted to ground. This method helps
distribute the heat between the NCx5652 and the current
limiting resistors during normal operation and for a short to
ground condition. Say that Figure 22 application example
will have a 3 V maximum output with a full load of 300 mA.
The RILIM resistors of 27 W are chosen so the voltage drop
across them will be greater than 3 V at a full load of 300 mA.
(VC1 = VC2 = 12 V – VD1− (RILIM * 300 mA) = 3.2 V).
Worst case is the voltage across RILIM will be ∼ 11.3 V. So
maximum current = 11.3 V / 27 W ∼ 420 mA.
If the power dissipation exceeds the thermal shutdown
limit, the thermal shutdown circuit will disable the outputs.
As discussed with the low to high short above, the
microcontroller should disable the outputs within 5 ms and
not enable them again for 5 seconds.
• Output short to ground
When possible, it is recommended that the application use
current limiting resistors to limit the output current to 1 A
D1
RILIM
27 W
VC1
12 V
RILIM
27 W
VC2
VC1
10 KW
VCC
EN VCC
−
1
Class
AB
Bias
0 to 3.8 V Input
2
5V
+
11
0.1 mF
VCC
10 KW
To microcontroller
1 mF
10
EN
5V
Load 1
500 mA
Max
9
1 mF
3
12
Thermal
Detection
From microcontroller
VC2
6
*Optional
EN VCC
VCC
8
1 mF
0 to 3.8 V Input
4
+
5
−
Class
AB
Bias
7
0.1 mF
Exposed
Pad (13)
NCx5652
10 KW
Figure 22. NCx5652 Application Diagram
www.onsemi.com
10
Load 2
500 mA
Max
NCS5652, NCV5652
DIS
ISC
ISC−PK
ISC−CLAMP
t
Continues Until Short is Removed
DISABLE/Tflag
DISHOLD
ISC−HOLD
TSHDN
EN
Figure 23. Output Short to Source. Output = VOL Shorted to 12−16 V
Table 6. SHORT CIRCUIT PARAMETERS
Parameter
Symbol
Peak Instantaneous Short Current
Short−Circuit Clamping Current
Disable Response Time after Thermal Shutdown
Min
Typ
Max
Units
ISC−PK
1000
mA
ISC−CLAMP
600
mA
DIS
5
ms
Disable Hold Time
DISHOLD
5
seconds
Short Circuit Hold Time*
ISC−HOLD
Varies
*Short circuit hold time is dependent on ambient temperature and printed circuit board characteristics.
Figure 24. Output Short to Source. Output = VOL Shorted to 12 V, TA = 255C
Figure 25. Output Short to Source. Output = VOL Shorted to 12 V, TA = −405C
www.onsemi.com
11
NCS5652, NCV5652
Figure 26. Output Short to Source. Output = VOL Shorted to 12 V, TA = 1255C
ORDERING INFORMATION
Device
Automotive
Marking
Package
NCS5652MUTWG
No
N5652
UDFN12, 3x3 mm
Pb−Free
NCV5652MUTWG
Yes
N5652
UDFN12, 3x3 mm
Pb−Free
Shipping †
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
12
NCS5652, NCV5652
PACKAGE DIMENSIONS
UDFN12 3x3, 0.5P
CASE 517AM
ISSUE O
A
D
PIN ONE
REFERENCE
2X
0.10 C
2X
ÇÇÇ
ÇÇÇ
ÇÇÇ
0.10 C
E
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
TOP VIEW
A
0.10 C
12X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
B
0.08 C
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.07 REF
0.20
0.30
3.00 BSC
2.40
2.60
3.00 BSC
1.60
1.80
0.50 BSC
0.20
−−−
0.30
0.50
A3
A1
C
SIDE VIEW
SEATING
PLANE
SOLDERING FOOTPRINT*
D2
6
1
12X
2.60
K
11X
0.35
(0.15)
12X
E2
0.60
1.80 3.30
12X
L
12
7
12X
b
e
0.10 C A B
0.05 C
NOTE 3
BOTTOM VIEW
1
0.48
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCS5652/D