NE5517 D

NE5517, NE5517A, AU5517
Dual Operational
Transconductance Amplifier
The AU5517 and NE5517 contain two current-controlled
transconductance amplifiers, each with a differential input and
push-pull output. The AU5517/NE5517 offers significant design and
performance advantages over similar devices for all types of
programmable gain applications. Circuit performance is enhanced
through the use of linearizing diodes at the inputs which enable a
10 dB signal-to-noise improvement referenced to 0.5% THD. The
AU5517/NE5517 is suited for a wide variety of industrial and
consumer applications.
Constant impedance of the buffers on the chip allow general use of
the AU5517/NE5517. These buffers are made of Darlington
transistors and a biasing network that virtually eliminate the change of
offset voltage due to a burst in the bias current IABC, hence eliminating
the audible noise that could otherwise be heard in high quality audio
applications.
http://onsemi.com
MARKING
DIAGRAMS
1
SOIC−16
D SUFFIX
CASE 751B
xx5517DG
AWLYWW
1
Features
•
•
•
•
•
•
Constant Impedance Buffers
DVBE of Buffer is Constant with Amplifier IBIAS Change
Excellent Matching Between Amplifiers
Linearizing Diodes
High Output Signal-to-Noise Ratio
Pb−Free Packages are Available*
1
xx
yy
A
WL
YY, Y
WW
G
Applications
•
•
•
•
•
•
PDIP−16
N SUFFIX
CASE 648
Multiplexers
Timers
Electronic Music Synthesizers
Dolby® HX Systems
Current-Controlled Amplifiers, Filters
Current-Controlled Oscillators, Impedances
NE5517yy
AWLYYWWG
1
= AU or NE
= AN or N
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
PIN CONNECTIONS
N, D Packages
IABCa 1
16
IABCb
Da 2
15
Db
3
14
+INb
−INa 4
13
−INb
VOa 5
12
VOb
V− 6
11
V+
7
10
INBUFFERb
VOBUFFERa 8
9
VOBUFFERb
+INa
INBUFFERa
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2013
June, 2013 − Rev. 4
1
Publication Order Number:
NE5517/D
NE5517, NE5517A, AU5517
PIN DESCRIPTION
Pin No.
Symbol
1
IABCa
Description
Amplifier Bias Input A
2
Da
3
+INa
Diode Bias A
Non-inverted Input A
4
−INa
Inverted Input A
5
VOa
Output A
6
V−
7
INBUFFERa
Buffer Input A
8
VOBUFFERa
Buffer Output A
9
VOBUFFERb
Buffer Output B
10
INBUFFERb
Buffer Input B
11
V+
12
VOb
Output B
13
−INb
Inverted Input B
14
+INb
Non-inverted Input B
15
Db
16
IABCb
Negative Supply
Positive Supply
Diode Bias B
Amplifier Bias Input B
V+
11
D4
D6
Q12
Q14
Q6
Q13
7,10
Q10
8,9
Q7
Q11
2,15
VOUTPUT
D3
D2
Q4
−INPUT
4,13
Q5
5,12
+INPUT
3,14
Q15
1,16
AMP BIAS
INPUT
Q2
Q16
Q3
D7
Q9
R1
Q1
D8
Q8
D1
D5
V−
6
Figure 1. Circuit Schematic
http://onsemi.com
2
NE5517, NE5517A, AU5517
B
AMP
BIAS
INPUT
B
DIODE
BIAS
B
INPUT
(+)
B
INPUT
(−)
16
15
14
13
B
OUTPUT
B
BUFFER
INPUT
V+ (1)
12
11
5
6
B
BUFFER
OUTPUT
10
9
7
8
−
B
+
+
A
−
1
2
AMP
BIAS
INPUT
A
NOTE:
DIODE
BIAS
A
3
4
INPUT
(+)
A
INPUT
(−)
A
OUTPUT
A
V−
BUFFER
INPUT
A
BUFFER
OUTPUT
A
V+ of output buffers and amplifiers are internally connected.
Figure 2. Connection Diagram
MAXIMUM RATINGS
Symbol
Value
Unit
Supply Voltage (Note 1)
Rating
VS
44 VDC or ±22
V
Power Dissipation, Tamb = 25 °C (Still Air) (Note 2)
NE5517N, NE5517AN
NE5517D, AU5517D
PD
Thermal Resistance, Junction−to−Ambient
D Package
N Package
RqJA
Differential Input Voltage
Diode Bias Current
1500
1125
140
94
mW
°C/W
VIN
±5.0
V
ID
2.0
mA
IABC
2.0
mA
Output Short-Circuit Duration
ISC
Indefinite
Buffer Output Current (Note 3)
IOUT
20
Operating Temperature Range
NE5517N, NE5517AN
AU5517T
Tamb
Amplifier Bias Current
Operating Junction Temperature
0 °C to +70 °C
−40 °C to +125 °C
mA
°C
TJ
150
DC Input Voltage
VDC
+VS to −VS
Storage Temperature Range
Tstg
−65 °C to +150 °C
°C
Lead Soldering Temperature (10 sec max)
Tsld
230
°C
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. For selections to a supply voltage above ±22 V, contact factory.
2. The following derating factors should be applied above 25 °C
N package at 10.6 mW/°C
D package at 7.1 mW/°C.
3. Buffer output current should be limited so as to not exceed package dissipation.
http://onsemi.com
3
NE5517, NE5517A, AU5517
ELECTRICAL CHARACTERISTICS (Note 4)
AU5517/NE5517
Characteristic
Input Offset Voltage
DVOS/DT
VOS Including Diodes
Input Offset Change
Test Conditions
Min
Symbol
Overtemperature Range
IABC 5.0 mA
VOS
Forward Transconductance
0.3
Diode Bias Current
(ID) = 500 mA
0.5
5.0 mA ≤ IABC ≤ 500 mA
VOS
0.1
IOS
0.1
Overtemperature Range
IBIAS
0.4
1.0
Typ
Max
Unit
5.0
0.4
mV
5.0
0.3
2.0
5.0
2.0
7.0
5
0.6
gM
Overtemperature Range
6700
5400
9600
5.0
8.0
Peak Output Voltage
Positive
Negative
Supply Current
VOS Sensitivity
Positive
Negative
RL = 0, IABC = 5.0 mA
RL = 0, IABC = 500 mA
RL = 0, Overtemperature
Range
RL = ∞, 5.0 mA ≤ IABC ≤ 500 mA
RL = ∞, 5.0 mA ≤ IABC ≤ 500 mA
IABC = 500 mA, both channels
IOUT
VOUT
ICC
CMRR
Common-mode Range
Differential Input Current
Leakage Current
5.0
500
BW
13000
mV
0.1
0.6
mA
mA/°C
5.0
7.0
7700
4000
9600
650
3.0
350
300
5.0
500
+12
−12
+14.2
−14.4
mA
mA/°C
12000
0.3
+14.2
−14.4
mmho
dB
7.0
650
mA
V
2.6
4.0
2.6
4.0
20
20
150
150
20
20
150
150
mA
mV/V
110
dB
±12
±13.5
±12
±13.5
V
100
dB
10
0.02
100
0.02
10
nA
0.2
100
0.2
5.0
nA
26
10
2.0
Unity Gain Compensated
SR
50
Buffer Input Current
5
INBUFFER
0.4
Peak Buffer Output Voltage
5
VOBUFFER
Refer to Buffer VBE Test
Circuit (Note 6)
3.0
80
IABC = 0 (Refer to Test Circuit)
Open-loop Bandwidth
0.1
110
IIN
RIN
mV
0.01
100
IABC = 0, Input = ±4.0 V
2.0
80
Referred to Input (Note 5)
20 Hz < f < 20 kHz
Input Resistance
Slew Rate
+12
−12
D VOS/D V+
D VOS/D V−
Common-mode Rejection
Ration
Crosstalk
350
300
0.5
0.4
1.0
0.3
Peak Output Current
mV/°C
0.001
0.01
gM Tracking
DVBE of Buffer
Min
0.001
Avg. TC of Input Current
DIB/DT
0.4
7.0
Avg. TC of Input Offset Current
Input Bias Current
Max
Avg. TC of Input Offset Voltage
Input Offset Current
DIOS/DT
Typ
NE5517A
26
kW
2.0
MHz
50
5.0
10
0.4
V/ms
5.0
10
0.5
5.0
mA
V
0.5
5.0
mV
4. These specifications apply for VS = ±15 V, Tamb = 25°C, amplifier bias current (IABC) = 500 mA, Pins 2 and 15 open unless otherwise
specified. The inputs to the buffers are grounded and outputs are open.
5. These specifications apply for VS = ±15 V, IABC = 500 mA, ROUT = 5.0 kW connected from the buffer output to −VS and the input of the buffer
is connected to the transconductance amplifier output.
6. VS = ±15, ROUT = 5.0 kW connected from Buffer output to −VS and 5.0 mA ≤ IABC ≤ 500 mA.
http://onsemi.com
4
NE5517, NE5517A, AU5517
TYPICAL PERFORMANCE CHARACTERISTICS
10 3
VS = ±15V
3
2
INPUT OFFSET CURRENT (nA)
+125°C
1
-55°C
0
-1
+25°C
-2
+125°C
-3
-4
-5
-6
-7
2
10
-55°C
10
+25°C
+125°C
1
2
-55°C
10
10mA
100mA
+125°C
1
0.1mA
1000mA
1mA
PEAK OUTPUT VOLTAGE AND
COMMON-MODE RANGE (V)
+125°C
10 3
+25°C
-55°C
10
4
VOUT
3
VCMR
2
10mA
100mA
RLOAD = ∞
0
-1
Tamb = 25°C
-2
VCMR
-3
-4
-5
-6
0.1mA
AMPLIFIER BIAS CURRENT (IABC)
+125°C
10 3
10 2
+25°C
10
1
2
3
4
5
6
INPUT DIFFERENTIAL VOLTAGE
Figure 9. Input Leakage
1mA
10mA
10 5
gM
10 4
100mA
10 3
0V
10 2
10
-50°C -25°C
1000mA
7
mq
m
M
VS = ±15V
-55°C
+125°C
10 2
+25°C
0.1mA
1mA
10mA
100mA
1000mA
AMPLIFIER BIAS CURRENT (IABC)
Figure 10. Transconductance
http://onsemi.com
5
0°C 25°C 50°C 75°C100°C125°C
AMBIENT TEMPERATURE (TA)
Figure 8. Leakage Current
10 2
PINS 2, 15
OPEN
10 3
10
0
1000mA
10 4
Figure 7. Peak Output Voltage and
Common-Mode Range
TRANSCONDUCTANCE (gM) — ( μ ohm)
10 4
100mA
Figure 5. Input Bias Current
AMPLIFIER BIAS CURRENT (IABC)
Figure 6. Peak Output Current
10mA
VOUT
-8
1000mA
1mA
AMPLIFIER BIAS CURRENT (IABC)
(+)VIN = (−)VIN = VOUT = 36V
VS = ±15V
1
-7
1mA
0.1mA
10 5
5
0.1mA
1000mA
Figure 4. Input Bias Current
VS = ±15V
1
100mA
AMPLIFIER BIAS CURRENT (IABC)
10 4
10 2
10mA
LEAKAGE CURRENT (pA)
1mA
Figure 3. Input Offset Voltage
PEAK OUTPUT CURRENT ( μ A)
10
3
+25°C
AMPLIFIER BIAS CURRENT (IABC)
INPUT LEAKAGE CURRENT (pA)
10
0.1
-8
0.1mA
1
VS = ±15V
INPUT RESISTANCE (MEG Ω )
INPUT OFFSET VOLTAGE (mV)
4
10 4
VS = ±15V
INPUT BIAS CURRENT (nA)
5
PINS 2, 15
OPEN
10
1
1
0.1
0.01
0.1mA
1mA
10mA
100mA
1000mA
AMPLIFIER BIAS CURRENT (IABC)
Figure 11. Input Resistance
NE5517, NE5517A, AU5517
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
7
+25°C
1200
1000
+125°C
800
600
400
5
RL = 10kW
OUTPUT DISTORTION (%)
CAPACITANCE (pF)
1400
Tamb = +25°C
6
-55°C
1600
CIN
4
COUT
3
2
IABC = 1mA
10
1
0.1
1
200
0
100
VS = ±15V
1800
0.1mA
1mA
10mA
100mA
0
1000mA
0.01
0.1mA
1mA
10mA
100mA
AMPLIFIER BIAS CURRENT (IABC)
Figure 12. Amplifier Bias Voltage vs.
Amplifier Bias Current
Figure 13. Input and Output
Capacitance
20
OUTPUT NOISE CURRENT (pA/Hz)
RL = 10kW
VIN = 80mVP-P
-20
VIN = 40mVP-P
-40
-60
OUTPUT NOISE
20kHz BW
-80
-100
0.1mA 1mA
Figure 14. Distortion vs. Differential
Input Voltage
600
VS = ±15V
0
1
10
100
1000
DIFFERENTIAL INPUT VOLTAGE (mVP-P)
1000mA
AMPLIFIER BIAS CURRENT (IABC)
OUTPUT VOLTAGE RELATIVE TO
1 VOLT RMS (dB)
AMPLIFIER BIAS VOLTAGE (mV)
2000
10mA
100mA
500
400
300
100
0
10
1000mA
IABC AMPLIFIER BIAS CURRENT (mA)
Figure 15. Voltage vs. Amplifier Bias Current
IABC = 1mA
200
IABC = 100mA
100
1k
10k
FREQUENCY (Hz)
100k
Figure 16. Noise vs. Frequency
+36V
A
4, 13
−
+15V
4V
11
5, 12
2, 15
7, 10
NE5517
+
4, 13
−
11
5, 12
2, 15
NE5517
8, 9
1, 15
3, 14
A
1, 10
3, 14
6
+
6
−15V
Figure 17. Leakage Current Test Circuit
Figure 18. Differential Input Current Test Circuit
V+
V
50kW
V−
Figure 19. Buffer VBE Test Circuit
http://onsemi.com
6
NE5517, NE5517A, AU5517
APPLICATIONS
+15V
3, 14
10kW
INPUT
0.01mF
−
390pF
1, 16
2, 15
51W
62kW
11
7, 10
NE5517
8, 9
5, 12
4, 13
1.3kW
OUTPUT
6 0.01mF
+
5kW
−15V
10kW
−15V
0.001mF
Figure 20. Unity Gain Follower
CIRCUIT DESCRIPTION
The circuit schematic diagram of one-half of the
AU5517/NE5517, a dual operational transconductance
amplifier with linearizing diodes and impedance buffers, is
shown in Figure 21.
If VIN is small, the ratio of I5 and I4 will approach unity and
the Taylor series of In function can be approximated as
KT In I 5 [ KT I 5 * I 4
q
q
I4
I4
and I 4 ^ I 5 ^ I B
Transconductance Amplifier
KT In I 5 [ KT I 5 * I 4 + 2KT I 5 * I 4 + V
IN
q
q 1ń2IB
q
I4
IB
The transistor pair, Q4 and Q5, forms a transconductance
stage. The ratio of their collector currents (I4 and I5,
respectively) is defined by the differential input voltage, VIN,
which is shown in Equation 1.
V IN
I5
KT
+ q In
I4
I 5 * I 4 + V IN
Where VIN is the difference of the two input voltages
KT ≅ 26 mV at room temperature (300°k).
Transistors Q1, Q2 and diode D1 form a current mirror which
focuses the sum of current I4 and I5 to be equal to amplifier bias
current IB:
11
ǒ
V IN I B
ǒI BqǓ
2KT
q
2KT
Ǔ+I
(eq. 5)
O
ǒI B qǓ
The term
is then the transconductance of the amplifier
2KT
and is proportional to IB.
(eq. 2)
V+
D4
D6
Q14
Q6
Q10
7,10
Q12
Q13
8,9
Q7
Q11
2,15
VOUTPUT
D3
D2
Q4
−INPUT
4,13
Q5
5,12
+INPUT
3,14
Q15
1,16
AMP BIAS
INPUT
Q2
Q3
R1
D8
Q8
D1
V−
6
Q16
D7
Q9
Q1
(eq. 4)
The remaining transistors (Q6 to Q11) and diodes (D4 to D6)
form three current mirrors that produce an output current equal
to I5 minus I4. Thus:
(eq. 1)
I4 ) I5 + IB
(eq. 3)
D5
Figure 21. Circuit Diagram of NE5517
http://onsemi.com
7
NE5517, NE5517A, AU5517
Linearizing Diodes
Impedance Buffer
For VIN greater than a few millivolts, Equation 3 becomes
invalid and the transconductance increases non-linearly.
Figure 22 shows how the internal diodes can linearize the
transfer function of the operational amplifier. Assume D2
and D3 are biased with current sources and the input signal
current is IS. Since I4 + I5 = IB and I5 − I4 = I0,
that is: I4 = (IB − I0), I5 = (IB + I0)
The upper limit of transconductance is defined by the
maximum value of IB (2.0 mA). The lowest value of IB for
which the amplifier will function therefore determines the
overall dynamic range. At low values of IB, a buffer with
very low input bias current is desired. A Darlington
amplifier with constant-current source (Q14, Q15, Q16, D7,
D8, and R1) suits the need.
APPLICATIONS
+VS
Voltage-Controlled Amplifier
ID
ID
2
* I
ID
S
2
I0 + 2 I
) I
S
ID
I5
I OUT + *V IN @
D2
1/2ID
IS
S
I0 + I5 * I4
I4
D3
In Figure 23, the voltage divider R2, R3 divides the
input-voltage into small values (mV range) so the amplifier
operates in a linear manner.
It is:
ǒǓ
IB
Q4
V OUT + I OUT @ R L;
I5
IS
1/2ID
A+
IB
Figure 22. Linearizing Diode
Since gM is directly proportional to IABC, the amplification
is controlled by the voltage VC in a simple way.
When VC is taken relative to −VCC the following formula
is valid:
For the diodes and the input transistors that have identical
geometries and are subject to similar voltages and
temperatures, the following equation is true:
ID
2
ID
2
V OUT
R3
+
@ gM @ R L
V IN
R2 ) R3
(3) gM = 19.2 IABC
(gM in mmhos for IABC in mA)
−VS
T In
q
R3
@ g M;
R2 ) R3
) IS
1ń2(I B ) IO)
+ KT
q In 1ń2(I B * IO)
* IS
I ABC +
(eq. 6)
(V C * 1.2V)
R1
The 1.2 V is the voltage across two base-emitter baths in
the current mirrors. This circuit is the base for many
applications of the AU5517/NE5517.
I
I
I O + I S 2 B for |IS| t D
2
ID
The only limitation is that the signal current should not
exceed ID.
INT
+VCC
VC
+VCC
R4 = R2/ /R3
R1
3
+
IABC
1
11
5
7
NE5517
VIN
R2
4
−
6
8
IOUT
RL
VOUT
RS
R3
INT
−VCC
TYPICAL VALUES: R1 = 47kW
R2 = 10kW
R3 = 200W
R4 = 200W
RL = 100kW
RS = 47kW
Figure 23.
http://onsemi.com
8
NE5517, NE5517A, AU5517
Stereo Amplifier With Gain Control
Modulators
Figure 24 shows a stereo amplifier with variable gain via
a control input. Excellent tracking of typical 0.3 dB is easy
to achieve. With the potentiometer, RP, the offset can be
adjusted. For AC-coupled amplifiers, the potentiometer
may be replaced with two 510 W resistors.
Because the transconductance of an OTA (Operational
Transconductance Amplifier) is directly proportional to IABC,
the amplification of a signal can be controlled easily. The
output current is the product from transconductance×input
voltage. The circuit is effective up to approximately 200 kHz.
Modulation of 99% is easy to achieve.
+VCC
10kW
VIN1
3
RIN
+
11
INT
+VCC
15kW
1k
RP
+VCC
NE5517/A
RD
4
IABC
−
8
1
RL
10kW
30kW
VC
VIN2
VOUT1
5.1kW
RC
10kW
14
RIN
15kW
1k
RP
+VCC
15
16
+
−VCC
IABC
+VCC
10
NE5517/A
12
RD
13
6
−
9
RL
10kW
VOUT2
RS
−VCC
INT
Figure 24. Gain-Controlled Stereo Amplifier
RC
30kW
VIN2
SIGNAL
1
IABC
+VCC
11
ID
15kW
VOS
VIN1
CARRIER
10kW
3
2
NE5517/A
1kW
4
INT
+VCC
+
5
7
−
8
RL
10kW
6
−VCC
Figure 25. Amplitude Modulator
http://onsemi.com
9
VOUT
RS
−VCC
INT
NE5517, NE5517A, AU5517
Voltage-Controlled Resistor (VCR)
Voltage-Controlled Oscillators
Because an OTA is capable of producing an output current
proportional to the input voltage, a voltage variable resistor
can be made. Figure 26 shows how this is done. A voltage
presented at the RX terminals forces a voltage at the input.
This voltage is multiplied by gM and thereby forces a current
through the RX terminals:
Figure 32 shows a voltage-controlled triangle-square
wave generator. With the indicated values a range from
2.0 Hz to 200 kHz is possible by varying IABC from 1.0 mA
to 10 mA.
The output amplitude is determined by IOUT × ROUT.
Please notice the differential input voltage is not allowed
to be above 5.0 V.
With a slight modification of this circuit you can get the
sawtooth pulse generator, as shown in Figure 33.
Rx +
R ) RA
gM ) RA
where gM is approximately 19.21 mMHOs at room
temperature. Figure 27 shows a Voltage Controlled Resistor
using linearizing diodes. This improves the noise
performance of the resistor.
APPLICATION HINTS
To hold the transconductance gM within the linear range,
IABC should be chosen not greater than 1.0 mA. The current
mirror ratio should be as accurate as possible over the entire
current range. A current mirror with only two transistors is
not recommended. A suitable current mirror can be built
with a PNP transistor array which causes excellent matching
and thermal coupling among the transistors. The output
current range of the DAC normally reaches from 0 to
−2.0 mA. In this application, however, the current range is
set through RREF (10 kW) to 0 to −1.0 mA.
Voltage-Controlled Filters
Figure 28 shows a Voltage Controlled Low-Pass Filter.
The circuit is a unity gain buffer until XC/gM is equal to
R/RA. Then, the frequency response rolls off at a 6dB per
octave with the −3 dB point being defined by the given
equations. Operating in the same manner, a Voltage
Controlled High-Pass Filter is shown in Figure 29. Higher
order filters can be made using additional amplifiers as
shown in Figures 30 and 31.
I DACMAX + 2 @
3
VC
IO
NE5517/A
5
C
−
7
4
200W
R ) RA
gM @ R A
INT
+VCC
11
+
2
RX +
30kW
+VCC
V REF
+ 2 @ 5V + 1mA
R REF
10kW
VOUT
8
200W
RX
−VCC
R
100kW
10kW
−VCC
INT
Figure 26. VCR
+VCC
VC
+VCC
ID
3
VOS
30kW
1
RP
2
INT
+VCC
11
NE5517/A
1kW
5
C
6
4
7
8
RX
−VCC
R
100kW
10kW
−VCC
INT
Figure 27. VCR with Linearizing Diodes
http://onsemi.com
10
NE5517, NE5517A, AU5517
30kW
1
+VCC
VIN
100kW
3
IABC
INT
+VCC
11
+
2
NE5517/A
5
−
6
4
200W
7
C
150pF
8
R
100kW
200W −VCC
RA
VC
VOUT
10kW
−VCC
INT
NOTE:
f
+
O
R A gM
g(R ) RA) 2pC
Figure 28. Voltage-Controlled Low-Pass Filter
30kW
1
+VCC
+VCC
100kW
VOS
NULL
3
2
IABC
5
−
6
4
1kW
INT
+VCC
11
+
NE5517/A
-VCC
RA
1kW
VC
0.005mF
7
C
8
R
100kW
−VCC
VOUT
10kW
−VCC
INT
NOTE:
f
O
+
R A gM
g(R ) RA) 2pC
Figure 29. Voltage-Controlled High-Pass Filter
15kW
+VCC
+VCC
NE5517/A
−
100pF
RA
200
NE5517/A
100kW
C
−
200W
−VCC
R
100kW
200W
10kW
RA
100
kW
RA
200W
-VCC
NOTE:
f
O
+
INT
+VCC
+
+
VIN
VC
R A gM
(R ) R A) 2p C
Figure 30. Butterworth Filter − 2nd Order
http://onsemi.com
11
C2
200pF
VOUT
10kW
−VCC
INT
NE5517, NE5517A, AU5517
1
+VCC
10kW
3
+
14
11
6
1kW
800pF
−VCC
13
20kW
12
NE5517/A
15
20kW
INT
+VCC
+
7
NE5517/A
−
VC
+VCC
5
2
15kW
16
−
10
LOW
PASS
VOUT
800pF
9
1kW
5.1kW
20kW
5.1kW
−VCC
−VCC
INT
BANDPASS OUT
Figure 31. State Variable Filter
30kW
+VCC
VC
+VCC
4
−
INT +VCC
13
11
1
5
7
3
+
C
0.1mF
6
12
NE5517/A
NE5517/A
−VCC
10
16
+
8
INT
+VCC
47kW
−
14
VOUT2
9
20kW
10kW
−VCC
INT
−VCC VOUT1
GAIN
CONTROL
Figure 32. Triangle−Square Wave Generator (VCO)
IB
IC
470kW
VC
1
+VCC
+VCC
4
+
13
11
5
2
3
R1
30kW
16
INT +VCC
7
−
C
0.1mF
6
8
−VCC
−
NE5517/A
NE5517/A
14
INT
47kW
12
+VCC
30kW
10
+
R2
30kW
20kW
−VCC
NOTE:
V PK +
−VCC VOUT1
(V C * 0.8) R 1
R 1 ) R2
TH +
2V PK x C
IB
TL +
2V PKxC
I
C
f OSC
IC
I t t IB
2V PKxC C
Figure 33. Sawtooth Pulse VCO
http://onsemi.com
12
VOUT2
INT
NE5517, NE5517A, AU5517
ORDERING INFORMATION
Device
Temperature Range
Package
AU5517DR2
AU5517DR2G
SOIC−16
−40 to +125 °C
SOIC−16
(Pb−Free)
NE5517D
SOIC−16
NE5517DG
SOIC−16
(Pb−Free)
NE5517DR2
SOIC−16
NE5517DR2G
SOIC−16
(Pb−Free)
NE5517N
Shipping†
0 to +70 °C
2500 Tape & Reel
48 Units/Rail
2500 Tape & Reel
PDIP−16
NE5517NG
PDIP−16
(Pb−Free)
NE5517AN
PDIP−16
NE5517ANG
PDIP−16
(Pb−Free)
25 Units/Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
13
NE5517, NE5517A, AU5517
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
9
−B−
1
P
8 PL
0.25 (0.010)
8
B
M
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
http://onsemi.com
14
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
NE5517, NE5517A, AU5517
PACKAGE DIMENSIONS
PDIP−16
CASE 648−08
ISSUE U
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS
WHEN FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE
MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
−A−
16
9
1
8
B
F
C
L
S
−T−
H
SEATING
PLANE
K
G
D
M
J
16 PL
0.25 (0.010)
M
T A
M
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740 0.770
0.250 0.270
0.145 0.175
0.015 0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008 0.015
0.110 0.130
0.295 0.305
0_
10 _
0.020 0.040
MILLIMETERS
MIN
MAX
18.80 19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0_
10 _
0.51
1.01
Dolby is a registered trademark of Dolby Laboratories Inc., San Francisco, Calif.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NE5517/D