NCP1397: 300 W SLIM LCD TV Power Solution

TND401/D
Rev. 2, September 2010
300 W High Performance
SLIM LCD TV Power Solution
Jean-Paul Louvel
LCD TV System Applications
© 2010 ON Semiconductor
Disclaimer: ON Semiconductor is providing this reference design
documentation package “AS IS” and the recipient assumes all risk associated
with the use and/or commercialization of this design package. No licenses to
ON Semiconductor’s or any third party’s Intellectual Property is conveyed by
the transfer of this documentation. This reference design documentation
package is provided only to assist the customers in evaluation and feasibility
assessment of the reference design. It is expected that users may make
further refinements to meet specific performance goals.
2
Table of Contents
Overview
LCD-TV Power Architecture and Evolution
Critical Design Objectives
Input Voltage
PFC
Standby Supply
System Supply
Backlight Supply
Height of parts
Standby Power Supply
Introduction
NCP1053A / 44 kHz
Mains supply for Standby SMPS
Primary side of Standby SMPS
Secondary side of Standby SMPS
Functional OFF Switch
Standby / ON control and over voltage protection
Secondary over voltage protection
Secondary 5 V Standby Output short-circuit to GND
Regulation open loop behaviors (Safety tests)
Overall Power and efficiency performances
Transformer design
EMI filter
EMI tests results
PFC stage
Frequency Clamped Critical conduction Mode (FCCrM)
Interleaved PFC and FCCrM
PFC Coils
Key parts size and design
Inrush current limiter
PFC-OK and POWER BOOST
OVP and UVP
Flyback converter
Introduction
5
7
10
10
10
10
10
10
10
11
11
12
12
13
18
19
19
20
20
22
23
24
25
25
28
28
30
31
37
38
39
42
44
44
3
QR Flyback with new NCP1379
Fix frequency PWM Flyback with NCP1252A
Design of the transformer
Starting phase
Primary circuit of QR Flyback with NCP1379
Primary circuit of PWM Flyback with NCP1252
Secondary side circuit of Flyback
Cross Regulation Considerations
Secondary regulation
Output current sense
Overload on 5 V / VS1
Short circuit on 5 V / VS1
Overload on 12 V / VS2
Short circuit on 12 V / VS2
Open regulation loop and Over Voltage Protection
Tests result with the QR open loop regulation
Overall Edge LED LCD TV solution
The 13 mm version
Introduction
Mains filters
PFC
Standby SMPS
Flyback
Heat sink
PCB
Conclusion
References
Our partners to design this application
Overall 8 mm SLIM schematics
BOM, overall with QR Flyback
BOM modifications for Flyback PWM NCP1252
Overall 13 mm schematics
Modified key parts for the 13 mm version
Overall 8 mm and 13 mm board pictures
45
45
46
47
48
51
54
54
55
56
58
59
60
61
63
64
66
67
67
68
68
68
69
69
70
70
71
72
74
78
87
88
91
92
4
Overview
This reference document describes a built-and-tested, GreenPoint® solution for
an LCD-TV power solution that combines the main system power without a
backlight power converter. In this architecture, the backlight power converter is
designed on a separated board to allow full design flexibility and easier
adaptation to any backlight solution and technology (Classical 24 V Hall Bridge
resonance Power Supply or LIPS / High Voltage Inverter for CCFL, Power
converter for Fronts or Edge LED Backlight or finally Power converter for PDP /
Plasma panel).
This reference design circuit consists of a 290 mm x 310 mm printed circuit board
designed to fit into the chassis of a Flat-TV. The height is limited to 8 mm to allow
advanced Slim & low depth LCD TV design. All the circuitry is resident in on a
single-sided PCB as might be found on an LCD-TV but with FR4 / Glass Epoxy
material. This allows large holes in the PCB without adding issues in drop or
vibration tests.
The low profile design has a direct impact on the passive component definitions.
The overall winding parts (common mode EMI filters, PFC coils, Standby and
Flyback transformers) have been defined with a low profile ferrite core and a new
bobbin, allowing the parts to be lower than 8 mm with holes in the PCB included.
The large electrolytic capacitors have been split into multiple lower values and
inserted flat on the board. They measure a diameter of 10 mm, and also include
holes in the PCB. The heat sinks have been designed with a new low profile
allowing them to be below 7 mm.
The ON Semiconductor devices utilized are from the latest generation of
controllers. This design has been engineered to achieve optimum performance
compared to traditional LCD-TV power architectures, while simplifying the overall
bill of materials. This is done by selecting a proprietary high performance low
power mode standby integrated switcher, a high efficiency interleaved Frequency
Clamp Critical Conduction Mode (FCCrM) PFC, and a Flyback controller
topology that provides the power to the overall TV signal processing and audio
amplifiers. To provide higher design flexibility, 2 types of Flyback controllers have
been considered requiring minimal changes to move from one to the other. The
first one is a new Quasi Resonance (QR) mode while the second is a fixed
frequency PWM.
5
Figure 1. System architecture of the 46” Power solution
6
LCD-TV Power Architecture and Evolution
One of the key differentiating factors of new large flat screen TV sizes over
previous ones is the thickness of the cabinet - the thinner the better. This
requires several considerations for the power supply design:
• The amount of power to be delivered is relatively large: the number of
watts per cm3 is much larger compared to a smaller screen size flat TV.
• Because the TV will be used in the living room, audible noise can be a
problem, and the use of fans is limited / prohibited.
• Overall cost in the competitive environment of the consumer electronics
world is critical.
• The panel, the power supply, and the audio amplifiers are close to each
other. Therefore the generation of EMI and susceptibility to EMC might
have an impact on the picture and sound quality.
Flat TVs require the generation of several voltage rails to power the different
system blocks such as audio, backlighting, and signal processing. The power
supply does not generate all the voltages required within the set. Instead, local
linear and DC-DC converters on the signal processing board are used to
provide the low voltage rails. It is fairly common for manufacturers to use a
universal power supply that supports 90-265 Vac. This allows a single power
supply design based on a specific TV size to be used for a series of models for
different regions, simplifying logistics and reducing development cost. If the
LCD-TV is intended for global use and the power is over 75 W, it is necessary
to comply with IEC 61000-3-2, the EU standard for harmonic reduction, so an
active power factor control stage is used.
The largest power consuming sub-system within the flat TV is the backlight.
Plasma technology was the first historical solution, however, Cold Cathode
Fluorescents Lamps (CCFL) with LCD panels previously used for note books
rapidly took the leadership. These florescent lamps started with only medium
sized screen TVs, but are now used at every size point.
Starting last year, the LED backlight solution for LCD TVs has become a very
popular way to allow small depth design with SLIM cabinets, particularly with
Edge LED solutions.
Newer backlight converters should be dedicated to providing full design
capability, and allowing the use of any backlight technology. Designed on a
separated board allows for fast evolution supporting all backlight requests and
new developments (Plasma, CCFL with classical 24V or LIPS solution and
new LED backlight for both Front and Edge technology). Also, an added
converter dedicated to the audio amplifier and signal processing, is designed
on the power board to provide similarity to any backlight technology.
7
The Power architecture solution is intended to improve overall system
efficiency. This is done with a high efficiency Flyback converter (signal
processing and audio amplifiers) and a backlight conversion stage directly
powered from the high voltage low profile Interleaved FCCrM PFC rail. This
has three primary benefits:
• Increases overall system efficiency.
• Reduces active power consumption and heat generation which
enhances system reliability and reduces component stress.
• Reduces the total number of parts to improve the overall bill of materials
cost.
Other drivers for this architecture are the increased consumer awareness of
the cost of energy, and new regulatory considerations. These are intended to
address overall power consumption of TVs and their impact on the
environment and energy infrastructure.
Historically, standby losses in consumer electronics were the primary concern
of government and power conservation agencies. This is because the devices
are always connected to the AC main and constantly consuming some power,
even in off mode. As a result, there are numerous voluntary and regulatory
standards around the globe intended to reduce standby power consumption
with the lowest limit of 0.3 W.
As this consumption is becoming more and more critical, key TV brand names
are looking for further improved performances with standby consumption < 0.1
W. If this is still not a mandatory performance, it is becoming an important key
feature which should help promote ECO Standby mode.
An alternative to this ECO Standby mode is an OFF mode which allows for <
50 mW or even 0.0 W in OFF mode. If the most conventional solution is to use
a mains switch, we will see later in this document, that there are alternatives
which provide better solutions for both cost and safety criteria.
As the screen size of direct view flat TVs increase, so does the ON mode
power consumption. As a result, regulatory agencies have become concerned
about the cumulative impact on the power grid of ON state power as flat TVs
gain market share and consumers switch from CRT and projection TVs to
large display direct view technologies such as Plasma and LCD-TV. In the US,
the Environmental Protection Agency (EPA) started a process in 2006 to
revise the existing voluntary Energy Star standard for TVs to include active
power consumption requirements as part of its criteria for qualifying energy
efficiency in TVs. This standard was revised and went into effect in November
2008 and now incorporates maximum active power requirements as a function
of screen size. As part of the specification development process, existing TVs
were evaluated to the proposed standards and at the time, less than 30% of
the TVs tested on the market met the active and standby test requirements.
The active power limits in the Version 4 Energy Star standard, effective in May
8
2010, are listed in the table below. As illustrated, there are a series of
equations based on screen area and vertical resolution to determine the active
power limit. For example, a 50” High Definition TV can consume no more than
153 W out of the box when tested against an internationally approved
audio/video test signal set which is meant to represent a common viewing
environment.
Table 1: Version 4 Energy Star Active Power Limits
Other countries have or are considering changes to their energy regulations to
drive the adoption of more power efficient TV products. For example, the
Japan Top Runner program takes a holistic approach which considers total
energy consumption (kWh/year) on an annual basis assuming 4.5 hours of
active use per day. This focuses the attention of TV manufacturers on
methods to optimize their system architectures for both active and standby
power consumption.
Finally TV manufacturers are starting to market the green aspects of their
products to highlight and differentiate their offerings and appeal to consumers
who are concerned about the rising cost of energy. While improvements in
active power go beyond the power supply including the display, backlight
source, video and audio signal processing, and control architectures. The
Power architecture in this reference design is designed from the ground up to
save power over the traditional architecture. Moreover, it is designed to
reduce the total system cost at the complete bill of materials level.
9
Critical Design Objectives
Input Voltage
•
Universal input 90-264 V ac, 47-63 Hz
PFC
•
•
•
Active Power Factor Corrected, IEC61000-3-2 Compliant
Up to 280 W input power capability
OFF in Standby mode
Standby Supply
•
•
•
Standby Pin < 90 mW with 40 mW load (8 mA on 5 V)
OFF mode Pin < 25 mW with added low power functional switch
Up to 1.5 A / 7.5 W Output power in ON mode
System Supply
•
•
•
•
•
•
Maximum steady state power 50 W, 70 Wpeak overall
12 V / 4 Apeak
5 V / 4 Apeak
24 V option on the PCB (not inserted on the first application)
Flexibility to be modified and support other voltage / current configurations
OFF in Standby mode
Backlight Supply
•
•
•
Maximum steady state power 150 W, 200 Wpeak
400 V from PFC Output for any backlight power converter build on
separated board
OFF in Standby mode
Height of parts
•
•
< 8 mm on top of PCB
< 12.5 mm total (Above PCB + PCB + Below PCB)
10
Standby Power Supply
Introduction
This converter has been primarily designed to provide a very low power
consumption allowing promotion of a very good ECO mode. The converter also
supports full standby performances allowing for remote control, IR function, and
peripheral control to start the TV (SCART specification in Europe). The current
consumption in Standby should remain below 8 mA / 40 mW to keep the overall
TV consumption under 90 mW. This may ask for dedicated Standby µP which is
becoming a greater state of the art technology for an ECO Standby mode.
Conventional fixed frequency switchers provide very good performances for the
Max output power due to the skip mode with current compression used to reduce
the possible noise issues. They do not however, provide the best results for very
low output power.
We did select hysteretic mode switcher NCP1053A to reduce the number of
switching cycles by light load and limiting the switching looses. This represents
the highest issue for high supply voltage applications (350 V). The reduced
features of this part also allow for a smaller internal consumption, which is a key
factor for high performances in OFF mode.
If a mains switch were widely used in Europe and Asia as with CRT TVs, Flat
TVs would not need the parts to be in line with safety / standard regulation (no
voltage > 4 kV). Despite it is not mandatory, we can see more and more flat-TVs
built with a mains switch to allow “Green OFF mode”. If this looks to be the
easiest / simplest solution, the high peak of inrush current and the requested
isolation needed around the switch (main isolation between switch + cable to
metal parts of the TV cabinet) make the mechanical design complex and costly in
order to avoid safety issues and risk of fire (witch may ask for VO cabinet plastic
material). The position of the switch in the cabinet is also critical as this may
increase the EMI issues with possible “by-pass” of the EMI filter due to the cables
position.
Thanks to the very good performances for the no load condition of our switcher
NCP1053A, we are able to provide an OFF mode below 25 mW consumption on
mains. This OFF mode is controlled through a small low voltage/cost switch
connected on the secondary side, without adding any isolation and EMI issues.
The solution is in line with the strongest safety requirements, does not allow the
TV to be switch ON (else the switch is closed), and never uses above 15 W
consumption for any safety tests.
To be able to keep such low power consumption in both Standby and OFF mode,
a relay is used to disconnect all parts which are not used in those modes (Mains
filters, X2 capacitors and associated discharged resistances, PFC with Brown
Out and Feedback, Flyback and Backlight converter). The relay, directly supplied
11
by 5 V Standby and controlled by TV µP, will avoid ~100 mW parasitic
consumption in Standby.
With mains disconnected from the PFC, the Standby SMPS should be supplied
with a dedicated diode directly connected to the mains input (before the relay).
As the power in Standby is limited, a single phase rectification is enough and the
“take over” from PFC output supplies the Standby SMPS with 400 V in ON Mode
to provide up to 7.5 W on the 5 V Standby output (1.5 A).
NCP1053A / 44 kHz
The NCP1053 is a monolithic high voltage Gated Oscillator Power Switching
regulator that enables end product equipment to be compliant with low standby
power requirements. This device series combines the required converter
functions allowing a simple and economical power system solution for consumer
products.
This device features an active startup regulator circuit that simplifies the starting
behaviors and reduces the consumption with an auxiliary bias winding on the
converter transformer, a fault detector and a programmable timer for converter
overload and Open Loop protection, unique gated oscillator configuration for
extremely fast loop response with double pulse suppression, power switch
current limiting, thermal shutdown, and auto restart fault detection. The design is
done with the lowest 44 kHz switching frequency to reduce switching looses as
much as possible. This device is available in an economical 8−pin dual−in−line
package.
Mains supply for Standby SMPS
RELAY1
VAC2
SW1
RELAY MODULE
5
8
4
1
3
6
2
7
RELAY2
D11
VAC1
F1
FUSE 6A-250V
1N4007 do41d
L006
1
VAC_VSS1
PFC_OUT2
D4 1N4007
1mH
cyld400l200c
do41d
+
LINE_NEUTRAL
90-264_VAC_INPUT
RV5
CN002
1
L
FG
CN001
4333-W05ST
FG
FG
1
CN402
Gnd_Lug
B72210P2321
rt100
2
F2
4R7 1W
Standby_supply
cyld8e5c
+
C24
10 uF 450V
bulk
C26
10nF 500V
C25
4.7 uF 450V
bulk
N
-
Figure 2. Standby Power Supply mains supply schematic
12
Despite the wide range of input supply (from 90 to 264 Vrms), thanks to the
limited standby consumption, a single diode rectification D11 from mains supply
is enough to keep the 10 µF 450 V input capacitor C24 charged. As the relay
SW1 is switched OFF in Standby mode, the mains overvoltage protection with
the varistor RV5 should be placed on Standby supply line to keep this protection
also in Standby. If the 6 A fuse F1 has the right value to protect the 300 W Power
converter, this is much too large to correctly protect a low power SMPS. An
added small F2 4.7 R 1 W 500 V Fuse resistance protects the Standby SMPS in
case of safety issues. To avoid possible reliability issues due to inrush current
stress, the capacitor C25 should be limited to 4.7 µF. The serial coil L006
provides the requested filtering to avoid EMI in Standby and also act as an inrush
limiter.
To be able to provide much higher power in ON mode (Up to 7.5 W), the PFC
Output takes over the supply through D4 with regulated 400 V.
Primary side of Standby SMPS
T100
SRW21EM-XXXX
3
Standby _supply
R100a
33K 2W
C100
1n 400V
C101
10p 1KV
NC
D101 1N4007
do41d
10
9
2
1
7
6
4
D104
1
Q101 BC808-25LT1
3
sot23
5
VCC2
VCC3
MMSD4148
sod123
2
D105
D102
VCC1
R113 4K7
MMSD4148
sod123
R122 220K
PC200B
4
R114
2K2
VCC0
BAV21
do41d
R103 4K7
SFH817A
3
dip4_3
+
C104
10u 25 V
4
STDBY _FB
PC100B
R120 0
SFH817A
dip4_3
1
2
C109
220p
3
IC100
NCP1053P44G
VCC
GND
Control in
GND
+
8
C105
47u 25 V
7
GND
3
VCC4
4
NC Power Drain
5
STDBY _MOS
HV Barrier
Figure 3. Standby Power Supply primary side schematic
13
Thanks to the embedded startup regulator, the Standby switcher IC100 is able to
start in short time over mains voltage range. As soon as the Vcc reaches 8.5 V
Vcc-start on C104, the IC starts switching, allowing energy to be transferred to
the secondary 5 V Standby. The auxiliary winding from the transformer, which
provides a voltage close to 15 V on C105, allows the switcher to be supplied with
better efficiency than when keeping the high voltage startup. The large value of
C105 keeps the IC supplied, even by light load and very low switching frequency.
A serial resistance R103 to the Vcc limits the current in the internal voltage clamp
build in the IC due to the variation of auxiliary voltage directly linked to large
output power range.
Starting phase (Independent from mains voltage and < 20 ms)
Vin = 90 V ac
CH1 => Vin DC
CH2 => VCC1
CH3 => 5 V output
CH4 => I primary
Vin = 230 V ac
CH1 => Vin DC
CH2 => VCC1
CH3 => 5 V output
CH4 => I primary
A classical RCD voltage clamp (R100, C100 and D101) limits the Max voltage on
the switcher. To avoid any possible reliability issues with short voltage transient,
the solution should be designed with an up to 100V margin and limited voltage
up to 600 V by Max output power. The size of the resistance could be reduced
down to ½ W. The added capacitor C101 is used to limit switching speed (or
dV/dt) and reduces EMI.
When the energy transferred to the secondary side is enough to provide the right
5 V, the opto coupler PC100 provides the regulation information directly applied
to “Control in” pin 2 of the IC. The IC, which works in hysteretic mode with
14
constant Max primary current internally limited, will provide the regulation and
adjust the energy transferred with variable number of missing cycles. For very
low output power in Standby mode, the controller will work with very low
frequencies, keeping the same Max current for each cycle, strongly reducing the
switching looses and so provides very good efficiency for low power / ECO mode.
OFF mode (No load) and Standby mode
Vin = 90 V ac
CH1 => V drain
CH3 => 5 V out (ripple)
CH4 => I primary
I out = 0 mA (No load)
5 V Output Ripple = 40 mV
F burst = 71 Hz
Vin = 90 V ac
CH1 => V drain
CH4 => I primary
I out = 0 mA (No load)
Nb cycles = 1
Expend of previous with 10 µs/div
Vin = 90 V ac
CH1 => V drain
CH3 => 5 V out (ac mode)
CH4 => I primary
I out = 8 mA
5 V Output Ripple = 80 mV
F burst = 322 Hz
15
Vin = 90 V ac
CH1 => V drain
CH4 => I primary
I out = 8 mA
Nb cycles = 1
Expend of previous with 10 µs/div
Vin = 230 V ac
CH1 => V drain
CH3 => 5 V out (ripple)
CH4 => I primary
I out = 0 mA (No load): Ripple = 42 mV
F burst = 64 Hz
Vin = 230 V ac
CH1 => V drain
CH4 => I primary
I out = 0 mA (No load)
Nb cycles = 1
Expend of previous with 10 µs/div
Vin = 230 V ac
CH1 => V drain
CH3 => 5 V out (ac mode)
CH4 => I primary
I out = 8 mA
Ripple = 73 mV
F burst = 291 Hz
16
Vin = 230 V ac
CH1 => V drain
CH4 => I primary
I out = 8 mA
Nb cycles = 1
Expend of previous with 10 µs/div
Standby to ON mode
With PFC “take over” by 90 V ac with 270 mA Output current on 5 V Standby
on top of the 80 mA for the relay to allow 9 mA on Vcc > 14 V (to supply PFC
and Inverter controllers)
Vin = 90 V ac
CH1 => Vin DC
CH2 => VCC4
CH3 => 5 V output
CH4 => STANDBY
ON mode with 400 V PFC Supply and Max
output current
5 V out = 4.85 V
I out = 1.82 A + I relay (80 mA)
IC100
V drain max = 580 V
I drain peak = 440 mA
V RCD clamp = 75 V
P RCD clamp = 170 mW
17
Secondary side of Standby SMPS
1
Key Pin-8
1
+
7
6
C102
R101
470µ 16V
1K
R104
10K
C106
PC100_DRV
100 n
1.25VREF
J201
1
2
IC101
TLV431ASN1
sot23-3
R105
10K
47µ 25V
V
6
1
F
u
0
7
4
1
3
VS-Stby
C103
+
2
SFH817A
ON-OFF Switch
"Optional"
4324-02S
e
t
a
n
r
e
t
l
A
2
R102
30K
CN100
2
1
VS-Stby
PC100A
dip4_3
INSTALL
N
1
J200
470
220nF
GND_STDBY
PC100A
5
2
R121
C108
4
HV Barrier
10uH
P
MBR3100
do201d
L100
2
2
V-Stby
1
NC
D100
10
9
N
3
P
T100
SRW21EM-XXXX
OFF Switch
Connection
INSTALL
GND_STDBY
Figure 4. Standby Power Supply secondary side schematic
The power supply has been designed to provide a single 5 V Standby up to 1.5 A
in ON mode. The rectifier diode D100 is a 3 A axial Schottky diode with 100 V
reversed voltage to keep a 20% margin even with 400 V PFC supply.
A TLV431, shunt regulator IC101, is used for the regulation (instead of TL431) to
reduce ECO mode consumption (lower current needed for polarization), and
have a greater voltage margin with a 5 V supply. An added RC network (R121 &
C108) provides output ripple information to the regulation and speeds up the
regulation by light load. This avoids double pulse in ECO mode and keeps the
switching frequency high enough to reduce ripple on the 5 V Output.
ON mode Max output power
5 V out = 4.85 V
I out = 1.82 A + I relay (80 mA)
D100
V max = 64 V (should be 100 V type)
I peak = 7.2 A
Expend of previous with 500 ns/div
5 V out = 4.85 V
I out = 1.82 A + I relay (80 mA)
D100
V max = 64 V (should be 100 V type)
I peak = 7.2 A
18
Functional OFF Switch
The switch can be much smaller than mains switch, requesting only 10 V and 2
Adc capabilities. Connected on the secondary side, there is no need of isolation
with any of the metal parts of the TV cabinet and does not represent any risk of
fire with voltage < 10 V. When used, the switch should be connected in series to
the filter coil L100 to reduce possible EMI issues (A 2 poles switch CN100 has
been put on PCB to allow easy connection of the OFF Switch). This switch will
interrupt the supply line of the TV µP, IR, and supply of the relay which can
switch ON the supply of the overall PFC and power converter.
The overall solution fulfills the safety requirements. It does not allow the TV set
to be switched to ON without an action on the switch and keeps consumption <
15 W on mains for any safety tests (short circuit or open circuit of any electrical
parts).
The Standby power supply will keep running without output load, with a
consumption < 25 mW on the mains by 230 V ac. This is a great alternative to
the mains switch which provides very good performances for much lower costs
and avoids possible safety issues.
Standby / ON control and over voltage protection
VS-Stby
HV Barrier
D109
Regulation
V1
MMSD4148
sod123
STANDBY
D108
MMSD4148
sod123
ZD101
R106
470
R107
4K7
1
RELAY1
RELAY2
RELAY 1
D110
RELAY 2
MMSD4148
sod123
PC200A
SFH817A
dip4_3
D103
MMSD4148
sod123
D106
MMSD4148
sod123
R108
NA
sod123
1
R110
1K
D107
R111
10K
2
sod123
MMSD4148
Q102
sot23
BC848ALT1
Q103
sot23
BC848ALT1
R116 100
R117
4K7
1
J202
MMSZ4690T1 (5V6)
VS1
R109
10K
3
Q100
BC858ALT1
2 sot23
ZD102
MMSZ4702T1 (15V)
VS2
R112
1K
sod123
R115 1K
R118
470
C107
10nF
2
INSTALL
GND_REG
Figure 5. Standby / ON secondary side schematic
The “STAND BY” control, coming from TV µP will control the power supply
allowing the system to go into ON mode or forcing it to stay in Standby.
A pull up resistance R108 (planned on the PCB) should be avoided in order to
reduce consumption in low power mode. To be able to drive the transistor Q102
19
correctly (witch should drive the relay with ~100 mA collector current capability),
the resistance R108 should be down to 1K which represents 5 mA consumption
when Standby control line is grounded through an open collector transistor. To
avoid that added power, we use a push pull output on the µP side allowing R108
to be removed.
With “STAND BY” control high up to 5 V, Q102 drives both the relay to supply the
PFC with mains voltage and the opto coupler P200 to supply all primary
controllers / ICs from Standby power supply auxiliary voltage VCC1 (Figure 3).
On the primary side, the opto coupler PC100 drives the PNP transistor Q101
which supplies all controllers (PFC, Flyback and backlight).
To get the correct Auxiliary voltage / Vcc1 (14 V minimum with 9 mA) needed to
be able to start the primary controllers, there is a need of a minimum output
current on 5 V Standby during the starting phase; 270 mA on top of the 80 mA
already requested to drive the relay. If the current is lower than the 270 mA, the
transformer should be modified (with more turns on auxiliary winding) to provide
the requested voltage.
To reduce power delivered from Standby SMPS in ON mode, the diode D104
takes over and provides the energy to those overall controllers from Flyback
auxiliary winding.
When the TV goes into Standby mode, both relay and opto will be switched OFF
when the Standby control line is going down.
To speed up the OFF switch of the flyback SMPS, the diode D103 will provide a
5 V on Flyback regulation input that will stop the converter immediately, avoiding
voltages to be kept a longer time and decreasing slowly without control.
This complete circuit will not be supplied (VS-Stby is null) if the “OFF Switch” is
OFF such that the TV set is blocked in OFF mode.
Secondary over voltage protection
Both Flyback Output VS1 and VS2 are monitored with Zener diodes ZD101 and
ZD102. If for any reasons, one of those voltages goes over the limit defined by
the respective Zener diode, the transistor Q103 will be switched ON and latch
with Q100, Q102 will be switched OFF through D107 and both relay and opto
should be immediately switched OFF avoiding further energy transferred from the
Flyback converter to signal processing and Audio amplifiers. The overall system
including PFC and backlight converter will be switched OFF as well. The Standby
SMPS should be switched OFF to allow possible restart (Latch OFF of both
Q100 and Q103).
Secondary 5 V Standby Output short-circuit to GND
In case of output short circuit to Ground, the current in the IC will be kept to the
same peak value, but since the transfer of energy cannot be completed, the
20
system will work in continuous mode with much higher rms current in the
transformer, IC, and diode. This will have direct impact on the temperature of the
parts with possible risks of safety issues. If the reflected voltage from the
secondary side should be low enough to avoid Vcc to supply the IC, the voltage
developed by the leakage inductance is enough to supply the IC thanks to its
extremely low consumption (this advantage is becoming an issue for safety tests).
As the regulation is OFF, there is no feedback to the controller which drives down
the regulation pin.
With an added pull-up resistance R122 of 220 K, we provide an “over voltage”
(voltage going out of regulation window) on the control in, since the opto does not
provide any feedback from secondary regulation (5 V is much too low). Thanks to
this new solution, the IC stops until Vcc decreases enough to allow re-start. The
power supply keeps running in low frequency (~ 7 kHz) burst or skip mode with
70% OFF time which avoids any over temperatures and safety issues.
This added resistance is mandatory in order to avoid the controller from running
with a secondary short circuit when supplying through leakage inductance effect
(enough to supply very low consumption controller).
Short circuit from 5 V Output to GND
Low frequency Burst mode
with 27% duty cycle / ON mode
CH2 => FB pin
CH3 => VCC1
CH4 => I Short circuit on 5 V
Expend of previous during ON time
Continuous Conduction Mode with 4 µs/div
IC100
V drain max = 450 V
I drain peak = 440 mA
21
Continuous Conduction Mode with 4 µs/div
D100
V max = 64 V (should be 100 V type)
I peak = 9 A
Regulation open loop behaviors (Safety tests)
The same added resistance R122 avoids open loop regulation issues with switch
OFF of the power supply keeping the system working in low frequency burst
mode.
Open circuit of Opto transistor PC200B in
ON mode
I out = 0 mA (worst case)
V out max = 7 V
CH3 => 5 V Standby
CH2 => Vcc1
Low frequency 8 Hz burst mode
Expend of previous during ON time
Iout = 0 mA (worst case)
Vout max = 7V
CH1 => V drain
CH3 => 5 V Standby
CH2 => Vcc1
ON time limited to 1 ms
Overall Power and efficiency performances
22
Overall Power and efficiency performances
0A
8mA
100mA
Pmax
Vout (V)
Pin (mW)
Pout (mW)
Efficiency (%)
Vcc1 (V)
Vout (V)
Pin (mW)
Pout (mW )
Efficiency (%)
Vcc1 (V)
Vout (V)
Pin (mW)
Pout (mW )
Efficiency (%)
Vcc1 (V)
Vout (V)
Iout
Pin (W)
Pout (W)
Efficiency (%)
Vcc1 (V)
90 Vac
4.94
19
0
xxx
10.9
4.94
84
40
48
12.5
4.93
846
500
59
17.9
4.9
583mA
4.72
2.85
61
23.3
230 Vac
4.94
24
0
xxx
10.1
4.94
86
40
47
12.3
4.93
819
500
61
17.6
4.85
1.82A
12.37
8.85
71
24.6
Table 2. Standby Power supply efficiency and performances
•
•
Pin < 25 mW for OFF mode / No load
Pin < 90 mW for 40 mW output on 5 V Standby
•
•
Up to 500 mA on 5 V Standby by 90 V ac in Standby mode
Up to 1.5 A on 5 V Standby by 230 V ac in Standby mode
•
Up to 1.5 A in ON mode
23
Transformer design
Parameters / Criteria
•
•
•
7.5 W Max Output on 5 V with 0.75% efficiency and 400 V supply from
PFC.
NCP1053A with 50 kHz switching frequency and 400 mA minimum current
(high value than IC spec due to propagation delay and di/dt).
To reduce possible noise issues, the transformer should be designed with
inductances low enough to keep it in discontinuous mode.
Specification
•
•
•
•
•
•
Primary inductance of 2.5 mH for Saturation current of 0.5 A.
Based on SRW2125 with PC40 EEM2125 core from TDK.
Np = 77 + 81 = 158 turns of 0.16 mm wire (secondary in sandwich
between both primary to reduce leakage inductance).
Ns = 2 x 11 turns of TEX 0.3 mm wire to provide requested isolation to
primary without isolation tape.
Nb = 26 turns of TEX 0.2 mm for auxiliary / Vcc winding.
The size of the transformer could have been smaller but there are very
few types of core and bobbin < 8 mm height capable of providing the
requested mains isolation with enough distance from ferrite to output
connections. Despite we use TEX wire which avoids margin tape, the
secondary output pin and connection should be 6 mm away from ferrite to
guarantee by construction the requested isolation to the primary side
(Ferrite is like a short circuit for isolation characteristics). Moving up from 8
to 13 mm height will provide a much larger number of possible solutions
with smaller bobbin and ferrite size.
24
EMI filter
VBD1
BD1
3
HS1
1
4
~
+
Heat_Sink
2 ~
- 1
GBU806
R255
C1
0.47uF
450V
10M 2W
C3
C4
Y 1nF
Y 1nF
C5
X2 100nF
275V
PH9090NL
VAC4
4
1
3
2
LN3
RV2
eclat
The input stage consists of two serial
common mode filters (L5 + L4)
combined to provide the right
inductance for such low profile parts.
A single capacitor filter 470 nF / C1,
placed after the bridge diodes
rectification is enough for differential
mode.
RV1
eclat
8.5mH
VAC3
L4
LN2
PH9090NL
4
1
RV4
eclat
RV3
eclat
3
2
8.5mH
C12
L5
X2 1uF
R17
Thanks to the interleaved PFC and the
much lower mains current ripple, the
classical differential mode filter
(position L1 and C2), used with
conventional single CrM PFC. can be
removed.
150K
R19
150K
R22
275V
R18
150K
R21
150K
150K
R23
150K
Varistor RV3, used to suppress high
energy pulses and mains surges
which may disturb overall operation,
has been moved to Standby supply to
be present in Standby when relay is
open.
RELAY1
VAC2
SW1
RELAY MODULE
5
8
4
1
3
6
2
7
RELAY2
VAC1
The overall function is placed after the
relay SW1 (OFF in Standby mode)
such that overall power parts are
disconnected from the mains. This is
particularly important for both X2
capacitors (1 µF / C12 and 100 nF /
C05) with their discharge resistances
R17 to R23 and the 60 mW
consumption at 230 V ac. The PFC
Brown Out and Feedback are also
disconnected avoiding consumption in
Standby mode.
Standby_supply
F1
FUSE 6A-250V
Gnd_Lug
CN402
LINE_NEUTRAL
90-264_VAC_INPUT
1
CN002
Figure 6. AC Input stage
1
L
FG
CN001
4333-W05ST
FG
FG
N
-
25
EMI tests results
Standby mode
• 230 Vac
• 0.5 W output
Average
The limit line is the lower solid line.
Peak The limit line is the upper solid line.
26
ON mode
• 230 Vac
• STDBY 4.93 Vdc 0.10 A 0.5 W
• +5V 5.01 Vdc 3.27 A 16.4 W
• +12V 12.38 Vdc 2.56 A 31.7 W
• 150 W on 400 V PFC for backlight
Average
The limit line is the lower solid line.
Peak The limit line is the upper solid line.
27
PFC stage
The active PFC front-end boost stage fulfils two requirements. First, it allows the
design to meet the harmonic content requirements of IEC61000-3-2 which
applies to power supplies with input power above 75 W. Secondly, it provides a
regulated 400 V high voltage rail for the overall converter including the backlight.
The Critical conduction Mode (CrM) PFC solution, also named boundary or
border-line or transient conduction mode, is a very popular operation mode for
low to medium power applications. If this is the base of our concept, our newest
ON Semi controller NCP1631 provides 2 newly added key features which
improve our PFC function.
Frequency Clamped Critical conduction Mode (FCCrM)
Frequency Clamped CrM (FCCrM) is a unique technique developed by ON
Semiconductor and embedded in controllers like the NCP1631. This controller
embeds an oscillator that sets the maximum frequency and operates:
• In Critical Conduction Mode when the current is longer than a preset time.
This duration threshold is the oscillator period that is programmed by an
external capacitor. Hence, the PFC stage operates in CrM in the most
stressful conditions.
• In Fixed Frequency (DCM) when the current cycle is short. The switching
frequency is that of the oscillator.
FCCrM controllers do not simply clamp the frequency.
Clamping the frequency of a CrM circuit dramatically affects the power factor.
That is why FCCrM controllers also modulate the on-time in DCM operation in
order to continue properly shaping the input current. More specifically, they
permanently monitor the dead-time relative duration over each switching period
and as a function of this information, modulate the on-time to compensate them
(see NCP1631 data sheet for more details). Thus, FCCrM PFC stage still exhibits
near-unity power factor even if the switching frequency is clamped.
More generally, they transition from CrM to DCM and vice versa without
discontinuity in the power transfer and without power factor degradation.
In addition, such a PFC stage can permanently operate in fixed frequency if the
inductor value is low enough, making the current cycle frequency remain below
the frequency clamp. However, this is not a recommended option. Because of
the dead-times, DCM needs higher peak inductor currents compared to CrM
ones for the same delivered power. Hence, DCM causes the current ripple and
its rms level to be larger. This creates heavy load conditions, reduces efficiency
and applies higher power stress on the inductor and on the MOSFET.
28
Instead, the inductor is designed to operate in CrM in the most stressful
conditions while DCM limits the switching frequency at light load and near the
line zero crossing. This option combines the merits of CrM and DCM.
Figure 7 - DCM and CRM Operation within a sinusoid cycle.
The (maximum) peak and rms inductor current are approximately the same as
the CrM, since the converter operates in CrM for the most stressful condition (low
line, full load).
(IL,pk )max =
(
2 2 ⋅ Pin,avg
(
Vin,rms
(IL,rms )max =
)max = 2
)LL
2 ⋅ 300
≅ 10 A
85
(IL,pk )max ≅ 10
6
6
≅4A
As aforementioned, the boost inductor must be large enough so that the system
operates in CrM at the top of the sinusoid when in low line, full load design that
is, in the most severe conditions. The equation is the same as the CrM one
except that the minimum frequency can be higher. Practically, the oscillator
frequency is generally set to 120 kHz. The minimum frequency has to be lower or
equal to this value, ( ( fsw )min ) and is actually set to about 20% to 50% lower for the
sake of margin and optimized efficiency .
L≥
⎛V
⎞
⋅ ⎜ out − Vin,rms
LL ⎟
⎝ 2
⎠=
⋅ Pin,avg
⋅ ( fsw )min
(Vin,rms )LL
2 ⋅ Vout
2
(
(
)max
)
390
− 85)
2
≅ 119 µH
2 ⋅ 390 ⋅ 300 ⋅ 70000
852 ⋅ (
A single 120 µH can then do the job instead of the two parts necessary for the
CrM option due to the higher inductance requested to keep the frequency low
enough.
29
Interleaved PFC and FCCrM
Interleaved PFC is an emerging solution that becomes particularly popular in
applications where a strict form factor has to be met, like for instance in the Slim
LCD TVs. Interleaving consists in paralleling two “small” stages in lieu of a bigger
one, which may be more difficult to design. Practically, two 150 W PFC stages
are combined to form our 300 W PFC pre-regulator.
Furthermore, if the two stages are operated out-of-phase, the current ripple is
significantly reduced. In particular, the input current looks like that of a
Continuous Conduction Mode (CCM) one and the rms current within the bulk
capacitor is dramatically reduced.
This approach has several merits like the ease of implementation, the use of
more but smaller components and a better heat distribution. In particular, an
interleaved PFC stage uses two small inductors instead of a larger one.
The NCP1631 is an FCCrM controller for 2-phase interleaved PFC applications.
Unlike master / slave controllers, it utilizes an interactive-phase approach where
the two branches operate independently in FCCrM. In addition, the NCP1631
unique interleaving technique substantially maintains the wished 180° phase shift
between the 2 branches, in all conditions including start-up, fault or transient
sequences.
In our application of interest (wide-mains, 300 W application), two identical
FCCrM 150 W PFC stages are to be designed. For each inductor, the
(maximum) peak and rms current are the same as the CrM but they must be
computed for half the total power. In other words:
(IL,pk )max =
2 2⋅
( Pin,avg )max
2
(Vin,rms )LL
(IL,rms )max =
(IL,pk )max ≅
6
5
6
⎛ 300 ⎞
2 2 ⋅⎜
⎟
⎝ 2 ⎠ ≅5A
=
85
≅2A
For each channel of the interleaved PFC, the boost inductor must be computed
as done for a 1-phase FCCrM PFC but for half the total power. Again, ( ( fsw )min ) is
set about 20% to 50% below the 120 kHz oscillator frequency for the sake of
margin. This leads to:
L≥
⎛V
⎞
⋅ ⎜ out − Vin,rms
⎟
LL
⎝ 2
⎠=
Pin,avg
max ⋅ f
⋅
( sw )min
2
(Vin,rms )LL
2 ⋅ Vout
(
2
(
)
)
390
− 85)
2
2 ⋅ 390 ⋅ 150 ⋅ ( fsw )min
852 ⋅ (
Provided the limited stress in the inductor, one 220 µH inductor per branch can
be implemented, for a 75 kHz minimal frequency (about 62% of the 120 kHz
30
clamp frequency). A more economical option consists in selecting a 150 µH
inductor per branch that corresponds to a 110 kHz minimal frequency or 92% of
the clamp frequency with direct impact of lower low-line efficiency.
This Frequency Clamped Critical conduction Mode (FCCrM) associated with the
interleaved approach allows for the use of smaller inductors in a PFC stage
which is a key advantage for Slim design requested for the new LCD TV design.
The additional advantages links to smaller rms input and output current allow
substantial cost reduction with much smaller output boost capacitors and avoid
completely differential mode EMI filter (like for CCM PFC).
PFC Coils
•
•
•
220 µH with up to 6Apeak current without saturation
PQM3811 from TDK with PC47PQM3811 A230 ferrite (AL = 230 nH)
31 turns of main coil and 3 turns for auxiliary ZCD control winding
•
A smaller 150 µH coil could have been used but due to the few possible
type of ferrite and bobbin < 8 mm, we keep this one with 220 µH such we
have better efficiency.
85 V 300 W ON Mode
CH1 and CH2 => V drain
CH3 and CH4 => I drain
Fsw min = 62 kHz
I peak = 5 A
CH1 => V drain
CH3 and CH4 => I drain
I peak = 750 mA
Fsw MAX = 86 kHz
31
CH3 and CH4 => I drain
CH2 => I Sense through R3 with added
current of both PFC
Current on the mains input supply line
With L1 differential filter
CH3 => I mains input
CH2 => I after L1
CH1 => VRM
Current on the mains input supply line
Without L1 differential filter (short circuit)
CH3 => I mains input
CH2 => I after L1
CH1 => VRMS
32
85 V 20 W ON Mode
CH1 and CH2 => V drain of both Power MOS
CH3 and CH4 => I drain of both Power MOS
Fsw = Min fixed 25 kHz
I peak = 2.8 A
Low mains frequency resolution
CH2 and CH4 => I drain of both Power MOS
CH3 => I mains input
Low mains frequency resolution
CH3 => I mains input
CH2 => I after L1
CH1 => VRMS
230 V 300W ON Mode
CH1 and CH2 => V drain of both Power MOS
CH3 and CH4 => I drain of both Power MOS
Fsw min = 112 kHz
I peak = 2.84 A
33
CH1 => V drain of 1 Power MOS
CH3 and CH4 => I drain of both Power
MOS
Fsw Max = 134 kHz
I peak = 630 mA
CH3 and CH4 => I drain of both Power
MOS
CH2 => I Sense through R3 with added
current of both PFC
Current on the mains input supply line
With differential filter
CH3 => I mains input
CH2 => I after L1
CH1 => VRMS
Current on the mains input supply line
Without L1 differential filter (short circuit)
CH3 => I mains input
CH2 => I after L1
CH1 => VRMS
34
230 V P MAX ON Mode
0.88 A / 350 W Max output power
CH1 and CH2 => V drain of both Power MOS
CH3 and CH4 => I drain of both Power MOS
Fsw min = 106 kHz
I peak = 2.96 A
CH1 => V drain of 1 Power MOS
CH3 and CH4 => I drain of both Power MOS
I peak = 660 mA
Fsw Max = 134 kHz
Current on the mains input supply line
CH3 => I mains input
CH2 => I after L1
CH1 => VRMS
35
230 V 20 W ON Mode
CH1 and CH2 => V drain of both Power MOS
CH3 and CH4 => I drain of both Power MOS
Fsw = 30 kHz
I peak = 1.7 A
Low mains frequency resolution
CH2 and CH4 => I drain of both Power MOS
CH3 => I mains input
Low mains frequency resolution
CH3 => I mains input
CH2 => I after L1
CH1 => VRMS
36
VRMS
PFC_OUT2
PFC_OUT
RT1
nc 2
Q2 NDF08N50ZG
to220decalD
sod123
D6 MMSD4148
1
3
1
R43
Q4
2
10K
BC808-25LT1
sot23
R7
Q1 NDF08N50ZG
to220decalD
sod123
D5 MMSD4148
1
3
1
Q3
2
BC808-25LT1
sot23
R15
1M
3
R9
1M
R42
10K
J104
DRIVE2
MMSD4148
sod123
R28
1M
R3
R11
2K2
0.065 2 W 5%
res1000
R12
C11
NA
R39
O_UVP
FB_PFC
ZCD1_16
IC1
1
FB_PFC
3
4
5
6
BO_PFC
7
C21
8
C13
R31
20K
C19
680n
220n
R41
270K
NA
NA
1K
ZCD2_1
C18
220p
2
NA
2
C17
INSTALL
1
R30
24K
R44
R16 22K
R14 22K
CN003
4324-07S
1
2
3
4
5
6
7
8
C8
C9
47u 450V 47u 450V
R24
1K5
DRIVE1
C10
D8
R29
120K
C7
10nF 500V
+
R13
1M
R20
1M
1nF
R10
1M
47
R6
47
220n
+
3
2
R8
1M
R5
1M
2
PFC3812QM
P
MUR550APF
DO201d
4
*
5 nc
R4
1M
D3
L3Q2
3
*
6
ZCD1
L3
N
200uH
MUR550APF
DO201d
Heat_Sink
HS2
1
nc 5
PFC3812QM
1
R2
1M
6
P
R1
1M
L2Q1
1
*
2 nc
C2
0.47uF
450V
D2
200uH
*
N
L2
3
ZCD2 4
NTC 20R
R32
270K
R33
39K
ZCD1
FB
PFC-OK
Rt
DRV1
OSC
Vcontrol
Freq-Fall Back
BO
OVP/UVP
O_UVP
R34
10K
NCP1631
ZCD2
GND
Vcc
DRV2
Latch OFF
CS
VCC4
16
15
PFC-OK
14
R26
2K2
R27
47k
13
12
R25
15K
Q6
11
1
C15
10
D10
MMSD4148
sod123
9
sot23
100n
NA
3
2
2
BC856ALT1
D12
MMSD4148
sod123
C20
R37
1K
10n
C22
R35
0
Q5
3
+
1
sot23
BC856ALT1
POWER_BOOST
R38
1K
R36
10k
1
C16
R40
10K
10u 50V
Q7
BC848ALT1
sot23
2
PC001A
SFH817A
dip4_3
Figure 8. Interleaved Frequency Clamped CrM PFC schematic
Key parts size and design
Thanks to the interleaved PFC which splits the power in 2 PFC stages, both
Power MOS and diodes should be design only for 150 W (P/2) PFC. This allows
us to use standard and smaller size ON Semiconductors parts:
• Power MOS Q1 and Q2: NDF08N50ZG 0.72 Rtyp 8 A 500 V TO220FP
New ON Semi parts now released.
• Ultra fast boost diode D2 and D3: MUR550APF Axial 5 A 520 V Ultra
fast diode specially designed by ON Semi for CrM PFC with lower Vf to
reduce power dissipation.
• BC808-25LT1 PNP transistor Q3 and Q4 to speed up the Power MOS
switch OFF.
The output capacitors, designed to support output boost rms current, have
reduced value thanks to interleaved advantages. Only 2 capacitors C8 and C9
37
are built on the Power board considering that a third one should be on the
backlight power converter (and directly in parallel to those 2).
The total overall rms current of 1 A (calculated for 250 W average power),
divided by 3, allows to use 39 or 47 µF 450 V 105°C 0.375 Arms type with 10 mm
diameter to fit below the 8 mm Max height of the board.
Inrush current limiter
The sudden application of the mains to a PFC circuit can result in a large in-rush
current and voltage overshoot. To resize the power components to handle this
transient event is cost prohibitive. Furthermore, since the PFC is configured in a
boost topology, the controller cannot do anything further to protect against this
inrush since the voltage is applied through the inductor and rectifier to the output
capacitor of the boost converter.
To address this, two rectifier diodes D1 and D13 have been added on the PCB
from the input voltage to the output voltage bypassing the inductor and diverting
the startup current to the bulk capacitor. The bulk capacitor is then charged to
the peak AC line voltage without resonant overshoot and without excessive
inductor current. After startup, both DBYPASS will be reversed biased and will not
interfere with the boost converter.
If a single diode should normally be enough, two are used in series to avoid over
heating of the overall PFC parts with short circuit of the single bypass diode
which connects the output to the input of the boost.
Moreover, to further reduce the in-rush current which can be critical for the
mains fuse (limited I2 x t), a 20 R NTC (negative temperature coefficient)
thermistor (RT1) is placed in series with the mains connection (before the bridge)
to limit the in-rush current. The resistance value drops from a few ohms to a few
milliohms as the device is heated by the I2R power dissipation. Alternatively (as
used in our application), this NTC can be placed in series with the boost diode.
This improves the active efficiency as the resistor only sees the output current
instead of the input current (particularly interesting for low US mains supply). This
allows using larger cold resistance NTC as current in ON mode is much reduced
< 1 A for 300 W on 400 Vdc.
If above solution is used for single CCM or CrM PFC, thanks to the double
interleaved PFC structure, the inrush current divided by 2 allows MUR550 CrM
diodes D2 and D3 to support the Inrush current with 75 A peak current IFSM
capability each.
The interleaved CrM PFC, combined with high cold impedance of the NTC,
allows designers to remove the 2 bypass diodes.
38
PFC-OK and POWER BOOST
The NCP1631 can communicate with the downstream converter. The signal
PFC-OK is high (5 V) when the PFC stage is in normal operation (its output
voltage is stabilized at the nominal level) and low otherwise.
This signal will become active when the starting phase is over and output voltage
well regulated. If any issues or fault occurs in ON mode, this signal will go down
to GND but will not go down when mains supply disappear.
If this behavior is right for the Flyback converter allowing the system to discharge
the boost PFC output cap keeping both 5 V and 12 V present as long as possible,
for backlight converter using Half Bridge Resonance LLC solution, this may
cause some additional stress on the power MOS which should be avoided.
An additional circuit (Q5, Q6 and Q7) provides a new signal “POWER BOOST”.
Supply by the PFC-OK, the starting phase with signal going up is the same than
original signal PFC-OK from IC. This added circuit acts for switch OFF phase
with direct control of PFC Output voltage. When PFC-OUT / FB-PFC are going
down to 2V (80% of nominal 2.5 V), Q6 conducts and switch OFF Q5 so that
POWER BOOST starts to fall. To speed up this signal, the transistor Q7, which is
switched ON, will pull down POWER BOOST further and faster down providing
info to the down stream converter of backlight that PFC-OUT is out of range.
FB_PFC
IC1
1
2
3
4
5
6
7
8
NCP1631
ZCD2
FB
Rt
OSC
Vcontrol
Freq-Fall Back
BO
OVP/UVP
ZCD1
PFC-OK
DRV1
GND
Vcc
DRV2
Latch OFF
CS
16
15
PFC-OK
14
R26
2K2
R27
47k
13
12
Q6
11
1
10
sot23
BC856ALT1
3
3
2
2
R25
15K
Q5
1
sot23
BC856ALT1
POWER_BOOST
9
C20
R37
1K
10n
Q7
BC848ALT1
sot23
R38
1K
R36
10k
1
R40
10K
2
PC001A
SFH817A
dip4_3
Figure 9. POWER-BOOST provides PFC-OUT status to Backlight
This signal provided through opto coupler PC001 to secondary side, call
POWER-OK, allows full control of the TV µP for switch OFF sequence when
mains disappear. This may allow getting similar switch OFF behavior than going
to Standby.
39
4
VS-Stby
POWER_OK
PC001B
3
SFH817A
dip4_3
R119
22K
GND_STDBY
POWER_OK
VS-Stby
CN101
4324-05S
5
4
3
2
1
Standby power and signal
To Signal processing board
STANDBY
Figure 10. POWER-OK provides PFC-OUT status to TV µP
Starting phase
V in = 90 V ac
No load
CH2 => VCC4
CH4 => VRMS
CH1 => PFC OUT
CH3 => PFC OK after 120 ms
V in = 90 V ac
Load => 100 W
CH2 => VCC4
CH4 => VRMS
CH1 => PFC OUT
CH3 => PFC OK after 160 ms
V in = 230 V ac
No load
CH2 => VCC4
CH4 => VRMS
CH1 => PFC OUT
CH3 => PFC OK after 65 ms
40
V in = 230 V ac
Load => 100 W
CH2 => VCC4
CH4 => VRMS
CH1 => PFC OUT
CH3 => PFC OK after 100 ms
V in = 230 V ac
CH3 => PFC OK
CH2 => POWER BOOST
CH4 => POWER OK
Same for 90 V ac, with or without load
Delay of 60 µs for POWER OK compared to
PFC OK
From ON to Standby
CH4 => STANDBY
CH2 => VCC4
CH3 => POWER BOOST
CH1 => PFC OUT
CH3 => PFC OK
CH2 => POWER BOOST
CH4 => POWER OK
POWER BOOST is going down when PFC
OK is going down as Vcc4 is going down
below 10 V and PFC IC switch OFF
41
Mains or Switch OFF
CH4 => VRMS
CH2 => BO
CH1 => PFC OUT
CH3 => POWER BOOST
POWER BOOST is going down when
PFC OUT drops below 80% / 320 V
CH2 => FB PFC
CH3 => POWER BOOST
CH4 => POWER OK
CH1 => PFC OK
POWER BOOST is going down when
FB PFC drops below 80% / 2 V
PFC OK stay ON until PFC IC switch OFF
OVP and UVP
The NCP1631 has been designed with dedicated OVP pin (on top of Feedback
one) allowing high level of protection for open regulation loop.
To reduce overall power dissipation if the relay is not inserted, both resistances
divider have been combined in our application. If this reduces the power, we now
have a direct link between both FB and OVP/UVP pins.
Regulation feedback to GND in ON mode
CH2 => FB PFC
CH4 => OVP / UVP
CH3 => POWER BOOST
CH1 => PFC OUT
OVP/UVP pin is also grounded: UVP is
activated and PFC switch OFF, PFC-OUT is
equal to mains peak rectified voltage (320 V
for 230 V ac)
42
Regulation feedback Open in ON mode
CH2 => FB PFC
CH4 => OVP / UVP
CH3 => POWER BOOST
CH1 => PFC OUT
Without Feedback information, the OVP pin
takes the regulation over with highest Output
voltage defined by the resistances divider.
Detailed function and design of the Interleaved CrM PFC
Please refer to the application note of NCP1631 which provides all information
and design tools necessary for the PFC design. They are all listed at the end of
this documentation.
43
Flyback converter
Introduction
With a dedicated converter to supply the backlight (on separated board), the
flyback SMPS is used to provide power to all the analog and digital blocks used
for control, signal processing, and audio amplification.
With an overall requested power up to 70 W, it is better to use a separated
Standby power supply to provide high ECO Standby performances: it is not
possible to be < 100 mW in Standby with a 70 W SMPS capable and all parasitic
consumption from mains filters and PFC.
With Flyback power supply completely OFF in Standby mode, there is no need of
added switches to disconnect output voltages and so avoid possible safety
issues with overheating of those switches with output overload or short circuit to
GND.
The Flyback converter has been designed to support general types of TV
applications with up to 3 output voltages which can be selected by transformer
design with adapted turn’s ratio of each secondary winding. The first application
that has been developed supports the most common application working with 5 V
and 12 V, with 50 W continuous power, up to 70 W peak with up to 4 A on each
of the 2 outputs.
The third output could be used for a 24 V most likely dedicated to Audio
amplifiers with lower current capability limited to 1 A or 2 Apeak.
To be able to support wider concept requests, the Flyback power converter has
been developed with the 2 basic Flyback possible solutions:
• QR variable frequency with minimum voltage switching solution, working
in discontinuous critical mode
• PWM Fix frequency allowing both discontinuous or continuous mode
according to output power conditions and transformer design
The design has been done with PCB supporting both controller positions allowing
fast change from one to the other, keeping the same power parts (transformer,
Power MOS, current sense and voltage clamp) and the same complete
secondary side solution: Less than 10 parts changed allow the modifications with
possibility to easily compare both solutions’ merits!
44
QR Flyback with new NCP1379
The NCP1379 is a high-performance circuitry aimed to powering quasi resonant
converters. Capitalizing on a proprietary valley lockout system, the controller
reduces the switching frequency as the power loading becomes lighter. This
results in a stable operation despite switching events always occurring in the
drain source valley. This system works down to the 4th valley and toggles to a
variable frequency mode beyond, ensuring an excellent low power mode
performance.
To improve the safety in overload situations, the controller includes an Over
Power Protection (OPP) circuit which clamps the delivered power at high line.
Safety wise, a fixed internal 80 ms timer relies on the feedback voltage to detect
a fault. Once the timer elapses, the controller stops and enters auto recovery
mode.
Particularly well suited for TV applications, the controller features a pin to
implement a combined brown out / overvoltage protection such that
• The converter starts switching only when supply voltage from PFC is at
the right level.
• The controller stops switching with detection of auxiliary overvoltage
following regulation open loop.
The NCP1379 has been designed without High Voltage Start connection,
especially for application with extra Standby SMPS with a low Vcc start of 12 V
directly applied from Standby SMPS.
The timer protection with auto restart allows the system to restart and work in
burst mode without switching OFF the Standby power supply.
Fix frequency PWM Flyback with NCP1252A
The NCP1252 controller offers everything needed to build cost effective and
reliable ac-dc PWM Fixe frequency current controlled switching power supplies.
Thanks to the use of an internally fixed timer, NCP1252 detects an output
overload by control of feedback regulation without relying on the auxiliary Vcc
drop (Mandatory when supplied from Standby SMPS). A Brown Out input offers
protection against low input voltages and improves the converter reliability and
safety behaviors. The switching frequency is adjustable with a single external
resistance allowing the optimum use of the transformer performances. An
external capacitor provides full flexibility of Soft start definition.
The NCP1252 is especially designed for application with extra Standby SMPS. It
has a low Vcc start of 12V directly applied from Standby SMPS.
The timer protection with latch asks the system to go in Standby to allow possible
restart (Vcc going down provides NCP1252 reset).
45
Design of the transformer
The design of the transformer has been done for the QR mode has this is the
most critical one.
All below equations are from NCP1379 / 1380 applications notes and
documentations.
N ps =
kc (Vout + V f )
BVdss k D − Vin ,max − Vos
=
d max =
⎞
2 Pout Clump Fsw
⎟⎟ + π
η
⎠
2 × 75 ⎛ 1
0.064444 ⎞
2 × 75 × 100 p × 45k
+
⎜
⎟+π
0.8 ⎝ 375
5.8 ⎠
0.8
2 Pout
2 × 75
=
2
I pri , peak Fswη 2.67452 × 45k × 0.8
I pri , peak L pri
Vin ,min
I pri ,rms = I pri , peak
I sec ,rms =
3 × (5 + 0.8)
⇒ N ps ≈ 0.064444
800 × 0.85 − 400 − 10
N ps
2 Pout ⎛ 1
+
⎜⎜
η ⎝ Vin,min Vout + V f
I pri , peak =
L pri =
=
I pri , peak
N ps
Fsw,min =
⇒ I pri , peak = 2.6745 A
⇒ Lpri = 582 µH
2.67 × 582 µ
45k ⇒ d max = 0.187
375
d max
0.187
= 2.67
3
3
⇒ I pri ,rms = 0.667 A
1 − d max
2.67
1 − 0.187
=
3
0.064444
3
⇒ I sec ,rms = 21.6 A
As results of above calculation, the transformer has been designed on SRW4549
bobbin and core from TDK as this was the right size < 8 mm height.
Specification:
•
•
•
•
•
•
Primary inductance of 0.65 mH for Saturation current > 3 A
Np = 45 + 45 = 90 turns of 0.3 mm wire (secondary in sandwich between
both primary to reduce leakage inductance)
Ns 5 V = 2 x 6 turns of 4 x 0.3 mm wire to provide requested current
capability
Ns 12 V = 2 x 8 turns of 4 x 0.2 mm wire to provide requested current
capability. This 12 V is build on top of the 5 V to improve cross regulation
Nb = 15 turns of 0.14 mm for auxiliary / Vcc winding
Isolation tap of 6.5 mm on both side to provide the requested isolation
46
Starting phase
The Flyback (Same behavior for both QR and PWM) is only starting from
Standby mode. As soon as Vcc4 is available for all primary ICs through the
Standby switch Q101, the PFC controller will be supplied so that PFC-OUT is at
400 V after 80 ms by 230 V ac (longer time for lower mains supply).
At that time, the PFC-OK is going up, allowing BO to be over 1 V threshold so
that Flyback (already supply from Vcc4) is starting with 5 V output, well regulated
after ~10 ms.
Flyback starting phase from Standby to ON
CH2 => VCC4
CH1 => PFC OUT
CH4 => BO
CH3 => VS1 / 5 V
47
Primary side circuit of QR Flyback with NCP1379
T200
SRW4549EM-XXXX
3
PFC_OUT
13
R252
33K 2W
R251
33K 2W
*
R200
33K 2W
SNUBR1
C200
10n 500V
SNUBR1
11
*
NC 2
D201
MUR180
T200-01 1
do41d
R205
1K
R203 33k
D205
BO
PFC-OK
R214 10k
MMSZ4702T1
R206
D203
sod123
D206
MMSD4148
470k
BO
IC200
NCP1379
MMSD4148
1
ZCD
CT
FB
BO
CS
VCC
sod123
ZD200
(15V)
8
sod123
5
4
+
12
*
10
*
C217
47u 25V
R213
Heat_Sink
HS3
1
470
7
T200-05
220
BAV21
do41d
C213
330p
2
FB
R207
VCC3
9
C214
100n
7
*
3
CS
C210
68p
4
R211
1K
C211
C212
1n
220p
R249
4K7
GND
DRV
PWM_VCC
6
5
DRV_QRM
R217 27
DRV_Q203
R218
C218
100p 1KV
3K3
sot23
1
3
2
Q204
BC808-25LT1
R220
47k
Gnd_Lug
CN403
R221
0.47R 2W
res1000
C225
1
Y 1nF
4
VCC4
6
*
CS
C215
R209 100
FB
8
sod123
MMSD4148
100n
PC101B
D209
Q203
STP5NK80ZFP
to220decalD
C216
+
SFH817A
3
dip4_3
10u 50V
Figure 11. Primary side of QR Flyback with NCP1379
Connected to the auxiliary winding through R205, the ZCD / pin 1 detects the
core reset event such that the controller will always drive the system with full
demagnetization. The value of the small capacitor C210 (with both R205 and
R211) will set the delay to switch by the minimum voltage and reduce as much
as possible switching looses and EMI. This will be true even by the fourth valley
when the output power is low.
Also, injecting a negative voltage smaller than 0.3 V on this pin during the
conduction of the power MOS will perform over power protection defined by
R206. The diode D203 allows both ZCD and OPP individual adjustment.
The secondary feedback opto coupler collector connected to the FB / pin 2 will
allow regulation via primary current regulation, lower voltage on this pin will
immediately reduce the output power.
The CS / pin 3 monitors the primary peak current going through the Power MOS
Q203 and the primary of the transformer. If the first level of 0.8 V limits the
48
current cycle by cycle and start the internal timer, the second level of 1.2 V
(150%) will switch OFF immediately and latch the IC as this is the result of strong
secondary diode short circuit.
The GND / pin 4 is connected to the primary ground.
The DRV / pin 5 is the driver’s output which directly drives the gate of external
Power MOS Q203. Although the IC is designed to directly drive large Power
MOS, an added external PNP transistor Q204 is used to reduce current loop and
possible EMI related to the high di/dt necessary to switch OFF the Power MOS in
a small amount of time.
The Vcc / pin 6 is the supply pin of the IC connected to the general supply Vcc4
through a dedicated filter (R209), after standby switch Q101 with energy coming
from Standby (Vcc1) or Flyback (Vcc3) SMPS.
To avoid direct impact of output power though leakage inductance on the primary
auxiliary voltage Vcc3, a large resistance R207 has been inserted in series to the
rectifier diode to get the closest voltage to the plateau which is the image from
output regulated voltage. This voltage Vcc3 is also used to detect over voltage
and acts to latch the IC through the BO pin protection.
The BO / pin 7 observes the HV rail or the voltage coming from PFC OK (through
the divider R203 and R214) to allow starting phase only when PFC-OUT supply
line is correct. It also offers a way to latch the circuit in case of over voltage event
through the diode D206 when the zener diode ZD200 is switch ON (Open
regulation loop protection) and provide 2.5 V to pin 7.
A capacitor connected to the CT / pin 8 acts as the timing capacitor in foldback
mode and adjusts the frequency in VCO mode.
As for general Flyback application, a voltage clamp is used to reduce the Max
voltage on the Power MOS linked to the leakage inductance of the transformer.
To avoid over temperature, up to 3 power resistances R200, R251 and R252 can
be used.
ON Mode with 400 Vdc supply for PFC
Low power mode
1 A on 5 V and 0.5 A on 12 V
V Drain
I Drain
Fix and low frequency of 24 kHz
49
½ Output power mode
2 A on 5 V and 2 A on 12 V
V Drain
I Drain
QR by second valley at 57 kHz
Full power mode
4 A on 5 V and 4 A on 12 V
V Drain
I Drain
QR mode by first valley at 42 kHz
Full power mode
4 A on 5 V and 4 A on 12 V
Secondary 5 V Diode voltage and current
V D210 < 52 V
I D210 up to 23 A peak
Full power mode
4 A on 5 V and 4 A on 12 V
Secondary 12 V Diode voltage and current
V D207 < 65 V
I D207 up to 17.5 A peak
50
Primary side circuit of Fix Frequency PWM Flyback with NCP1252
T200
SRW4549EM-XXXX
3
PFC_OUT
R252
33K 2W
R251
33K 2W
13
*
R200
33K 2W
C200
10n 500V
SNUBR1
*
NC 2
11
D201
MUR180
T200-01 1
do41d
D205
R207
VCC3
MMSZ4702T1
ZD200
(15V)
T200-05
sod123
4
+
R203 33k
470
1
2
3
CS
IC202
NCP1252
FB
SS
BO
Vcc
CS
DRV
7
6
2
DRV_FLY
R247
C233
4
R214
10k
1n
C235
220p
C234
1n
R248
100K
C237
1u 50V
C236
100n
C216
10u 50V
8
Q203_G
Q203_S
3K3
sot23
1
*
sod123
MMSD4148
CS
+
3
R220
47k
2
Q204
BC808-25LT1
7
6
C218
100p 1KV
Gnd_Lug
CN403
R221
0.47R 2W
res1000
C225
1
Y 1nF
4
R250
15K
D209
R218
5
10
dip4_3
3
SFH817A
GND
+
FB
PC101B
RT
10K
*
Q203
STP5NK80ZFP
to220decalD
DRV_Q203
27
*
9
Q208
BC858ALT1
sot23
3
R246
1
8
*
Heat_Sink
HS3
1
VCC4
FB
12
C217
47u 25V
R213
R209 100
BO
PFC-OK
5
220
BAV21
do41d
Figure 12. Primary side of PWM Flyback with NCP1252
The secondary feedback opto coupler collector connected to the FB / pin 1 will
allow regulation via primary current regulation, lower voltage on this pin will
immediately reduce the output power.
The BO / pin 2 observes the HV rail or the voltage coming from PFC OK (through
the divider R203 and R214) to allow a starting phase only when PFC-OUT supply
line is correct.
The CS / pin 3 monitors the primary peak current going through the Power MOS
Q203 and the primary of the transformer. If the first level of 1V limits the current
cycle by cycle and start the internal timer with latch−off at the end. This allows
accurate overload or short−circuit detection which is not dependant on the
auxiliary winding. Reset occurs when: a) a BO reset is sensed, b) VCC is cycled
down to VCC (min) level. If the short circuit or the fault disappear before the fault
timer ends, the fault timer is reset only if the CS pin voltage level is below 1 V at
least during 3 switching frequency periods. This delay before resetting the fault
timer prevents any false or missing fault or over load detection.
51
It also offers a way to latch the circuit in case of an over voltage event through
the transistor Q208 when the Zener diode ZD200 is switch ON (Open regulation
loop protection) and provide 2.5 V to pin 3 during OFF time of Power MOS Q203.
A resistor connected from pin RT / 4 to ground fixes the switching frequency.
The GND / pin 5 is connected to the primary ground.
The DRV / pin 6 is the driver’s output which directly drives the gate of external
Power MOS Q203. Although the IC is designed to directly drive large Power
MOS, an added external PNP transistor Q204 is used to reduce current loop and
possible EMI related to the high di/dt necessary to switch OFF the Power MOS in
a very short time.
The Vcc / pin 7 is the supply pin of the IC connected to the general supply Vcc4
through a dedicated filter (R209), after standby switch Q101 with energy coming
from Standby (Vcc1) or Flyback (Vcc3) SMPS.
To avoid direct impact of output power though leakage inductance on the primary
auxiliary voltage Vcc3, a large resistance R207 has been inserted in series to
rectifier diode to get voltage close to the plateau which is the image from output
regulated voltage. This voltage Vcc3 is also used to detect over voltage and acts
to latch the IC through the CS pin protection.
The SS / pin 8 allows external capacitor C237 connection which defines the soft
start of the IC.
As the switching frequency has been chosen to be close to the QR Flyback one
in order to keep the same transformer, the same voltage clamp is used to reduce
the Max voltage on the Power MOS linked to the leakage inductance of the
transformer. To avoid over temperature, up to 3 power resistances R200, R251
and R252 can be used.
ON Mode with 400 Vdc supply from PFC
Low power mode
1 A on 5 V and 0.5 A on 12 V
V Drain
I Drain
V drain max = 592 V
Fsw = 46 kHz
52
½ Output power mode
2 A on 5 V and 2 A on 12 V
V Drain
I Drain
V drain max = 672 V
Fsw = 42 kHz
I peak = 1.84 A
Full power mode
4 A on 5 V and 4 A on 12 V
V Drain
I Drain
V drain max = 742 V
Fsw = 43 kHz
I peak = 2.61 A
VRCD = 235 V PRCD = 1.67 W
Full power mode
4 A on 5 V and 4 A on 12 V
Secondary 5V Diode voltage and current
V D210 < 49 V
I D210 up to 22 A peak
Full power mode
4 A on 5 V and 4 A on 12 V
Secondary 12V Diode voltage and current
V D207 < 65 V
I D207 up to 20 A peak
53
Secondary side circuit of Flyback (Same for both QR and PWM)
T200
SRW4549EM-XXXX
3
13 T200-13
*
11 T200-11
J302
C207
+
N
1
L201
1
2
10uH
2
VS2
cy ld400l200c
+
P
5
D207
1000u 16V
P
1
insert
1
insert
1
V2
2
2
J301
P
*
2
3
C205
+
C209
470u 16V
ZD201
MMSZ4692T1 (6V8)
sod123
Q202
R215
7
220
MJD200
DPAK
R216
220
T200-67
8
6
2
D210
1
1000u 16V
V1
Heat_Sink
HS4
1
1
C219
+
N
*
C221
+
1000u 16V
3
MBRF20L80CTG
to220
Gnd_Lug
CN403
C225
Q205
BC858ALT1
sot23
L202
10uH
2
VS1
cy ld400l200c
P
9
*
MBRF20L100CTG
to220
V1
10
+
R219
4K7
3
2
1
N
*
P
*
N
4
1000u 16V
P
N
N
12
D211
MMSD4148
sod123
R222
4K7
C224
470u 16V
R223
1K
Regulation
1
Y 1nF
Figure 13. Secondary side of Flyback (same for both solutions)
Cross Regulation Considerations
Achieving good cross regulation is a design challenge in LCD-TV applications as
the tolerances are tight, typically +/- 5% and the dynamic operation can vary
widely due to the high dynamic range of the audio amplification and the variety of
signal processing power load depending on the input video source. Below is the
typical output voltage and load range for the baseline reference design.
+5 V from 1 to 4 A
+12 V from 0.5 to 4 A
To improve the overall cross regulation performance, the +5 V diode is
connected in the ground (GND) of the winding with +12 V on top of the 5 V
54
winding. The drawback of that is that both +5 V and +12 V current go through
the 5 V diode and winding (increasing power loses mainly in the +5 V diode), the
advantage of this configuration is that the 12 V only sees 7 V of variation. An
additional advantage of this construction is that the reverse voltage of the 12 V
diode D207 is limited by the same difference. Note the transformer was designed
with a low turn’s ratio thus reducing the effective current but increasing the
reverse voltage of the diode. In the reference design, a 100 V is used for the 12
V to ensure adequate design margin and avoid the possibility of any reliability
issues while an 80 V type is used for the 5 V to reduce the power looses thanks
to lower Vf.
On top of this winding construction, the transformer has been designed to avoid
too much difference of coupling from primary winding to each secondary one: a
better coupling of the 12 V winding will unbalance the conduction of both
secondary 5 V and 12 V diodes which has an immediate direct impact on the
cross regulation performances. The transformer has been specially designed on
these criteria, but unfortunately with a direct impact on the overall primary
leakage inductance which asks for an 800 V Power MOS (Instead of the 700 V
type expected).
To be able to support a further larger range of output power / currents (Request
to be confirmed according to output power range and expected cross regulation
performances), an added voltage clamp has been inserted on the PCB.
Monitored by the zener diode ZD201, the difference between both 12 V and 5 V
is now limited, avoiding the 12 V to go up or the 5 V to go down. As soon as the
difference exceeds 7.5 Vtyp, the bipolar NPN transistor Q202 will start
conducting to derive a current from 12 V to 5 V and so keep “under control” the
difference. The serial resistance R215 is in to limit the gain and avoid possible
oscillations. The transistor Q202 is a DPAK type allowing power dissipation with
a large surface of PCB (This part should be changed to TO220 type and put on
diodes heat sink if more power dissipation is requested).
Secondary regulation
The secondary regulation is done on both 5 V / VS1 and 12 V / VS2 allowing
better overall performances.
As the 5 V asks for lower tolerance, 2/3 of the regulation is coming form the 5 V
with only 1/3 from the 12 V.
The IC201 / TL431 will drive the current in opto PC101 according to output
voltage such that high voltage will increase the current in the opto to drop down
the FB pin of the primary controller such that power transferred is decreased
allowing correct regulation.
55
Output current sense
To be able to fulfill all possible safety tests, the Switch Mode Power Supply
should be able to manage short circuit or over load on each Output.
Direct short circuit is not an issue as this will result in a very high current
dropping down all output voltages and detectable by primary over current
protection such that IC will stop and restart if not latched. Working by very low
frequency should avoid any over temperatures issues (for QR mode).
Much more critical for SMPS are short circuits far-away on the circuit after serial
impedances such like copper tracks, cables and even filter coils. The serial
impedances will limit the current and may not allow activating the primary over
current protection. This is an unlikely risk on the 12 V as voltage is large enough,
but this is a major issue for low voltage like 5 V. If for any reason, the 12 V is not
loaded when overload on 5 V happens, the total 70 W will be available with up to
14 A on 5 V before primary start to limit! In that case we will have up to 3 times
the nominal current on 5 V without any stop which results in high temperatures
on 5 V parts creating possible risks of fire on the board.
To avoid thi safety issues, a current sense has been developed on 5 V using the
voltage drop of filtering coil to avoid any added power parts and added voltage
drop which has a direct impact on output regulation performances (regulation is
done before the filter coil).
C219
N
+
1000u 16V
Q205
BC858ALT1
sot23
L202
10uH
2
VS1
P
cyld400l200c
+
R219
4K7
3
2
1
N
P
1
D211
MMSD4148
sod123
R222
4K7
C224
470u 16V
R223
1K
Regulation
Figure 14. Low voltage / 5V Output current limitation
To be able to adjust the level according to the requested limit, a pre-polarization
of the sense PNP bipolar transistor Q205 has been done with an added diode
D211 such that only 0.3 V drop on L202 provides the 0.6 V on Q205 Base
Emitter and so provides an added level of information on “Regulation”. The
resistances divider R219 / R222 should be adjusted according to the impedance
of L202 and the defined current limitation (adjusted to limit by 6 / 7 A on our
application to provide up to 4 A without any issues).
56
The added information provided to “Regulation” will change the regulation from
“Voltage control” to “Current control” such that the current on the 5 V will be
limited to the defined value.
R225 1K
C227 0R / Jumper
R245 0
V_123
V2
R236
470
D215
R226 750
PC101A
MMSD4148
sod123
V1
PC101A 1
D217
C228 470nF
dip4_3
2
VS-Stby
R227
1K
R237
10K
C230
470nF
R231 16K2
VS1
2
TL431BCLPRA
VS_123
2_5VREF
1
R232 6K19
to92d
3 Q207
BC858ALT1
sot23
2
R238
10K
D219
0R / Jumper
sod123
+
R233
2K4
N
IC201 3
1
VS2
PC101_DRV
MMSD4148
sod123
P
SFH817A
C232
470u 16V
D221
Regulation
GND_REG
R228 100
BAT54T1
sod123
Figure 15. Regulation with Output Under Voltage Protection
To avoid too strong working conditions, an additional under voltage protection
has been inserted to switch OFF completely the power supply when 5 V Output
is below a defined limit.
Q207 is used as a comparator which is switch ON as soon as VS1 is below:
5 V Standby + 0.6 V (D217) – 1.2 V (Q207junction and R divider R237/238) = 4.5 V
As soon as Q207 is switched ON, an added voltage is applied through D221 on
TL431 regulation such that primary controller will reduce the power transferred to
secondary and even stop completely when Q207 is ON applying more than 3 V
on TL431 Vref. This solution will keep the SMPS in OFF mode until secondary 12
V is down such that the secondary protection circuit is not supply any more,
allowing the primary IC to restart again.
As this circuit should not be activated during the starting phase, the supply will
come from the 12 V Output (through R236) going up with the same slop than the
5 V with an added delay defined by R236 and C232.
This circuit has some limitations. Due to the good cross regulation of the
transformer, the 12 V will not be able to reach this nominal value if the overload
on 5 V happens during the starting phase. With reduced 12 V, the voltage
applied through Q207 on TL431 reference will be smaller so that the time needed
to switch OFF completely the power supply will be longer. To reduce this effect,
D221 (mandatory for the starting phase) has been changed to Schottky (reduced
Vf).
57
The PCB has been design to allow under voltage control also on VS2 (not
inserted on our developed solution).
Overload on 5 V / VS1
Tests done on QR Flyback with NCP1379
(Similar behavior with PWM Flyback and NCP1252)
Output current I = 6.5 A (4 A is the maximum nominal current)
Primary side:
CH1 => V drain
CH4 => I primary
I peak = 2.90 A
Fsw = 20 kHz
V drain max = 670 V
Secondary side:
CH3 => I 5 V
CH4 => 5 V Out
CH2 => V Collector Q205
Working conditions of the secondary
rectifier diode D210
CH2 => V D210 (V max = 50 V)
CH4 => I D210 I peak = 24 A
58
Short circuit on 5 V / VS1
Tests done on QR Flyback with NCP1379
(Similar behavior with PWM Flyback and NCP1252)
Primary side:
CH1 => V drain
CH4 => I primary
I peak = 2.90 A
F sw = 11 kHz
V drain max = 620 V thanks to lower
reflected voltage
Secondary side:
CH3 => I 5 V
CH4 => 5 V Out
CH2 => V Collector Q205
CH1 => VCC3
Expend of previous waveforms
CH3 => I 5 V
CH4 => 5 V Out
CH2 => V Collector Q205
CH1 => VCC3
59
Working conditions of the secondary
rectifier diode D210
CH2 => V D210 (V max = 52 V)
CH4 => I D210 I peak = 25 A
Overload on 12 V / VS2
Tests done on QR Flyback with NCP1379
(Similar behavior with PWM Flyback and NCP1252)
Output current I = 5.5 A (4 A is the maximum nominal current)
There is no need of dedicated output current sense: thanks to the higher voltage,
the overall power is high enough to reach the limit and activate embedded
primary controller safety behavior.
Primary side:
CH1 => V drain
CH4 => I primary
I peak = 2.90 A
Fsw = 15 kHz
V drain max < 650 V
Secondary side:
CH3 => I 12 V
CH4 => 12 V Out
CH2 => V Collector Q205
CH1 => VCC3
60
Expend of previous waveforms
CH3 => I 12 V
CH4 => 12 V Out
CH2 => V Collector Q205
CH1 => VCC3
Working conditions of the secondary
rectifier diode D207
CH2 => V D207 (V max = 60 V)
CH4 => I D207 I peak = 18.2 A
Short circuit on 12 V / VS2
Tests done on QR Flyback with NCP1379
(Similar behavior with PWM Flyback and NCP1252)
Primary side:
CH1 => V drain
CH4 => I primary
I peak = 2.90 A
Fsw = 7.3 kHz
V drain max < 600 V thanks to lower
reflected voltage
61
Secondary side:
CH3 => I 12 V
CH4 => 12 V Out
CH2 => V Collector Q205
CH1 => VCC3
Expend of previous waveforms
20 ms/div
CH3 => I 12 V
CH4 => 12 V Out
CH2 => V Collector Q205
CH1 => VCC3
Working conditions of the secondary
rectifier diode D207
CH2 => V D207 (V max = 54 V)
CH4 => I D207 I peak = 18.5 A
62
Open regulation loop and Over Voltage Protection
As part of standard safety tests, the open regulation loop is one of the most
critical because it can create output over voltages on most of the down parts and
destroy the signal processing.
The overall application has a double Flyback output voltages protection.
The first one, located on the secondary side, will be able to directly measure
output voltages and act to switch OFF in Standby mode.
VS-Stby
HV Barrier
D109
Regulation
V1
MMSD4148
sod123
STANDBY
D108
MMSD4148
sod123
ZD101
R106
470
R107
4K7
1
RELAY1
RELAY2
RELAY 1
D110
RELAY 2
MMSD4148
sod123
PC200A
SFH817A
dip4_3
D103
MMSD4148
sod123
D106
MMSD4148
sod123
R108
NA
1
R110
1K
D107
2
sod123
MMSD4148
Q102
sot23
BC848ALT1
Q103
sot23
BC848ALT1
R116 100
R117
4K7
1
J202
MMSZ4690T1 (5V6)
VS1
R109
10K
R111
10K
sod123
3
Q100
BC858ALT1
2 sot23
ZD102
MMSZ4702T1 (15V)
VS2
R112
1K
sod123
R115 1K
R118
470
C107
10nF
2
INSTALL
GND_REG
Figure 16. Secondary Flyback Over Voltage Protection
As soon as one of the output voltages (VS1 or VS2) is going over the limit
defined by Zener diodes (ZD101 or ZD102), the transistors Q103 will be switched
ON, forcing the system to go in Standby mode by switching OFF the transistor
Q102. The relay is switched OFF such that mains voltage is disconnected from
the board. The system is locked by the transistor Q100 which provides a
“thyristor” effect to keep both Q103 and Q100 saturated until 5 V Standby is
going down.
This solution is accurate thanks to direct / secondary side voltage control.
If this solution reacts quickly on the secondary side, it is unfortunately slow on the
primary side: the large bulk capacitors on the PFC Output keep stored energy for
the overall system (including the Flyback) such that converters keep running until
the voltage is too low to supply them. This allows the Flyback to work open loop
with further increased output over voltages on secondary side.
63
An added / second circuit located on the primary side will act to switch OFF
immediately the Flyback converter as soon as Over Voltage is detected on the
auxiliary Vcc supply.
With QR solution (Figure 11), the over voltage detected by the Zener diode
ZD200 will be applied through the diode D208 to the BO input (pin 7) of the
controller NCP1379. As soon as the voltage is over 2.5 V on BO, the controller is
latch OFF until Vcc resets (Standby mode to disconnect the supply from Standby
SMPS) allowing possible restart.
With PWM solution (Figure 12), the over voltage detected by the Zener diode
ZD200 will be applied through the transistor Q208 to the CS input (pin 3) of the
controller NCP1252 during the OFF mode of Power MOS to avoid any current
limitation impact (and avoid on going primary regulation). As soon as the voltage
is over 1 V on CS, the internal Timer will be started and the controller will latch
OFF after 15 ms. A Vcc reset (Standby mode to disconnect the supply from
Standby SMPS) allows possible restart.
Tests result with the QR NCP1379 open loop regulation
Tests been done with 2 A on both 5 V and 12 V output
Tests done in ON mode (after starting)
CH4 => 5 V Out (6.7 V Max)
CH1 => BO / Latch Flyback IC
CH2 => RELAY2 switch OFF
Tests done in before starting
40 ms/div
CH4 => 5 V Out (6.9 V Max)
CH1 => BO / Latch Flyback IC
CH2 => RELAY2 switch OFF
64
Tests done in before starting
Expend of previous:10 ms/div
CH4 => 5 V Out (6.9 V Max)
CH1 => BO / Latch Flyback IC
CH2 => RELAY2 switch OFF
65
Overall Edge LED LCD TV solution
A backlight power solution has been developed by On-Semiconductor to provide
with the 46” Power a complete Edge LED LCD TV solution (Both boards have
been designed to be interconnected).
Directly supplied by PFC output, a Half Bridge LLC converter (new NCP1397
Half Bridge LLC controller) supplies all LED segments with a DC output voltage
(100-300 V).
The new CAT4026, 6-channel Edge LED linear driver provides
• Current regulation for each separated segments
• Voltage Feedback Control to External DC-DC converter
• Current Feedback Control to primary power supply Half-Bridge Resonant
Converter (NCP1397)
• PWM and Analog Dimming
• Auto-Recovery Fault Detection (All Modes)
• Shorted Cathode-Anode (SCA) Fault Protection
• Open Cathode-Anode (OCA) Fault Protection
• Over-Voltage Protection (OVP)
• Thermal Shutdown Protection
The overall design is also a Low Profile Design 8 mm thickness.
Power Supply
LED Backlight
Figure 17. Overall Edge LED LCD TV bloc diagram
This LED Backlight solution will also be very soon available.
66
The 13 mm version
Introduction
To be low profile below the requested 8 mm height, most of the larger parts
(winding parts, capacitors) and the PCB design should be specific:
• All winding parts (mains filters, PFC coils, Standby and Flyback transformers)
should be based on specific / very low profile bobbin with dedicated ferrite
form factor
• All large capacitors should be split to multiple lower value’s one connected in
parallel, with lower diameter case and inserted horizontally / flat on the board
• All heat sinks should be designed with low profile allowing components to be
easily removed for service without the need to de-solder all the parts
• The PCB design should be done:
o With large holes allowing the larger parts (above coils, transformers
and capacitors) to be partly below the PCB to reduce the height on top
of PCB plan
o Those high numbers of holes have a strong impact on PCB
mechanical performances such that glass epoxy / FR4 material is
mandatory despite we have a single layer design
o The lower height of the used parts asks for larger PCB surface
All above design constraints have a direct impact on solution cost which makes a
lower profile solution much more expensive. If moving from 25 to 13 mm height
has a limited impact, moving further down to 8 mm asks for very specific parts,
limited possible suppliers with possible procurement difficulties, and in any case
strong overall solution cost impact.
To reduce this height impact on the overall solution cost, a pre-design has been
done to provide a similar solution with 13 mm height allowing the use of more
standard parts
• With same performances (ECO Standby…) and power capabilities
• With the same overall concept, controller / ICs, Power MOS and diodes
• With more standard larger diameters capacitors with radial auto insertion
when possible (secondary Flyback filtering)
• With more standard higher profile heat sink allowing surface reduction
• With single sided PCB design, without holes for parts insertion allowing
reduction of the total surface and classical CEM1 lower cost PCB material
67
Mains filters
The 2 common mode filters use a higher, more standard core compared to the
very low profile one used for the 8 mm version (should be very low to avoid holes
in the PCB which makes the fixation very difficult).
If we keep the same inductance L > 8.5 mH, for the 13 mm, the resistance of
each winding goes down to 85 mR (to be compare with 105 mR for the 8 mm)
allowing higher current / power capability.
The single differential mode filter (when used) also has the same inductance L >
50 µH, for the 13 mm, the resistance of the winding goes down to 75 mR (to be
compare with 95 mR for the 8 mm) allowing higher current / power capability.
The X2 capacitors are the same but the larger 1 µF can be inserted without
creating holes in the PCB for the 13 mm version.
Both types of common mode and differential mode filters for the 8 and 13 mm
versions are from the same supplier Pulse, but with different reference and cost
(~ + 25% for the 8 mm).
The same applies to the relay, inserted horizontally / flat on the board, for both
versions but without holes in the PCB for the 13 mm version.
PFC
With the 13 mm version, we have been able to use the standard EFD30 bobbin
and ferrite without any holes in the PCB for both PFC coils. The inductance L is
200 µH (220 µH for the 8 mm) with the same 6 A current capability.
• Wurth Electronik provides the 13 mm version.
• TDK provides the SLIM 8 mm version with a special low profile PQM3811
(~ + 60% added cost compare to the EFD30).
If the 450 V Output capacitors should be inserted horizontally / flat on the board
for both versions, we are able to use 12.5 mm diameter / 40 mm length without
holes in the PCB for the 13 mm where a 10 mm diameter / 45 mm length with
holes is mandatory for the 8 mm.
We have used the same type and suppliers with different reference for both
versions with expected added cost for the smaller 10 mm diameter capacitors.
Standby SMPS
If in the 13 mm version the capacitors can be inserted vertically / automatically
radial, then the main difference is the transformer.
For the 8 mm version, we have been forced to use an oversized transformer to
get the limited height with respect of the requested mains isolation (with enough
distance from ferrite to pin despite we use TEX wire for secondary winding).
68
For the 13 mm version, we use a smaller transformer based on E12 ferrite which
provides the right isolation thanks to special bobbin design and TEX wire. The
primary inductance is the same 2.5 mH. The same current capability and the
same controller NCP1053A allow the solution to provide the same 7.5 W in ON
mode thanks to the take-over which supplies the Standby SMPS with 400 V from
PFC.
Transformers are from different suppliers:
• The E12 (13 mm) is from Wurth Electronik.
• The EEM2125 (8 mm) is from TDK (~ + 200% added cost compare to the
E12 which is due to the lower profile and the larger size).
Flyback
For the 13 mm, all output capacitors have been limited to 470 µF 16 V allowing
vertical / radial insertion. Some of those capacitors are in parallel to each other to
acquire the right value and rms current capability.
Similar to the Standby, the main difference is again the transformer:
• With a primary inductance L = 650 µH for up to 2.8 A for both type.
• For the 13 mm, we are able to use the same EFD30 bobbin and core than
for the PFC from the same supplier Wurth Electronik.
• For the 8 mm, we use a new low profile bobbin and EEM4549 core from
the same supplier TDK (~ + 75% added cost compare to the EFD30 which
is due to the lower profile and the larger size).
The vertical / radial inserted output filter coils could also be different but as the
price is similar, it is favorable to use only the 8 mm type from Wurth Electronik
with L = 10 µH for 4 A current capability.
Heat sink
To be able to improve the cooling as much as possible with the smallest possible
surface on the PCB, 2 type of profiles have been developed to support both
height versions.
To be able to keep both PCB designs as similar as possible, we have changed
“only” the width to compensate for the height reduction allowing us to keep the
same thermal performances and the same position of the parts on the length of
the heat sinks:
• The wide is 60 mm for the 7 mm height.
• The wide is 50 mm for the 12.5 mm height.
• The lengths are the same for both versions and link to function / position
and power dissipation.
69
PCB
With the 20 holes we have in the 8 mm PCB, used to reduce the total height < 8
mm, the PCB material should be a glass Epoxy FR4 to provide the right
mechanical performances. Due to the lower parts profile, the surface of the PCB
is larger, up to 310mm x 290 mm = 89 900 mm2
Without any holes in the PCB, the 13 mm design allows to use CEM1 material
(which provides better mechanical performances than standard FR1 or FR2).
The size of the board is 230 mm x 290 mm = 66 700 mm2
Due to the material and process (drilled), the m2 of FR4 is ~ 3 x the CEM1’s one.
Considering also the larger surface, the 8 mm PCB price is ~ 4 time the 13 mm’s
one.
Conclusion
This power solution can be designed using the same concept for both heights of
8 mm and 13 mm providing the same performances. If the 8 mm provides a
much more attractive SLIM solution, the need of special parts and specific PCB
design will have a direct impact on overall solution cost. The 13 mm version is an
alternative allowing cost improvement when the 8 mm height is not mandatory.
Further on, total solution cost improvement (with the same concept) could be
considered if the height moves up from the 13 mm to 25 mm as this will allow the
use of even more standard parts (mainly for heat sinks, capacitors and
transformers).
The 13 mm design has not been completed to provide boards to our customers
but information and support are available on request (All key parts are defined
and approved allowing easy spin-off from the 8 mm version).
Data sheets, applications information and samples for the ON Semiconductor
components are available at www.onsemi.com .
Links to the datasheets of the main components used in this design are included
in the below references.
Author of this document is:
Jean-Paul Louvel CCPG - LCD TV System Applications Manager
70
References
ECO Standby SMPS
NCP1053A specification
http://www.onsemi.com/pub_link/Collateral/NCP1050-D.PDF
Interleaved Frequency Clamped CrM PFC
NCP1631 specification
http://www.onsemi.com/pub_link/Collateral/NCP1631-D.PDF
NCP1631 Design Worksheet
http://www.onsemi.com/pub_link/Collateral/NCP1631%20DWS.XLS
iPFC - Interleaved Power Factor Controller Tutorial
http://www.onsemi.com/pub_link/Collateral/TND380-D.PDF
Key Steps to Design an Interleaved PFC by the NCP1631
http://www.onsemi.com/pub_link/Collateral/AND8407-D.PDF
Improve
the
Low-Power
Interleaved PFC
Efficiency
of
NCP1631-D
http://www.onsemi.com/pub_link/Collateral/AND8456-D.PDF
QR Flyback
NCP1379 specification
http://www.onsemi.com/pub_link/Collateral/NCP1379-D.PDF
NCP1379, NCP1380 Design Worksheet in MathCad
NCP1380 DWS.MCD
Designing a Quasi-Resonant Adapter Driven by the NCP1380
http://www.onsemi.com/pub_link/Collateral/AND8431-D.PDF
AD2 - Adapter Less than 75 W
http://www.onsemi.com/pub_link/Collateral/TND355-D.PDF
LCD - AC-DC Power Architecture in LCD TV
http://www.onsemi.com/pub_link/Collateral/TND353-D.PDF
PWM Flyback
NCP1252 specification
http://www.onsemi.com/pub_link/Collateral/NCP1252-D.PDF
71
Our partners to design this application
I would like here to thanks all of our suppliers working with us as partners,
providing very good support with samples to support our customers despite the
very challenging request and schedule. They all commit to provide the same
support to our customers for all needed information and samples related to parts
been used in our Power design.
Heat sink (New design for both 8 mm and 13 mm)
Columbia Staver Ltd
Tel: + 44 1268733346
Designer: John Norwood [[email protected]]
Managing Director: Anthony Smith [[email protected]]
Mains filters (For both 8 mm and 13 mm)
Pulse Europe
Gerard Healy
Email: [email protected]
website: http://www.pulseeng.com/
PFC coils, Standby and Flyback transformers (For 8 mm)
TDK Electronics Europe GmbH
Martin Appel
Tel: + 49 211 9077 104
Email: [email protected]
http://www.tdk-components.de
PFC coils, Standby and Flyback transformers (For 13 mm)
Würth Elektronik eiSos GmbH & Co. KG
Contacts: [email protected]
Flyback output filter coils (For both 8 mm and 13 mm)
Würth Elektronik eiSos GmbH & Co. KG
Contacts: [email protected]
72
Electrolytic capacitors (For both 8 mm and 13 mm)
Rubycon Corporation (Japan) Branch Munich
Takayuki KAWAKAMI
Tel: + 49 89 930 86 250
e-mail:[email protected]
Europe Chemi-Con
Christian MICHEL
Tel : + 33 1 64 16 02 19
email : [email protected]
web : www.EuropeChemiCon.de
Inrush current limiter and Varistor (For both 8 mm and 13 mm)
EPCOS SAS
Jacques Levéziel
Tel. +33 1 49 46 67 85
email : [email protected]
web : www.epcos.fr
73
8 mm SLIM Mains filters and PFC schematic
VRMS
J101
PFC_OUT2
2
GBU806
R255
C1
0.47uF
450V
C4
*
R1
1M
200uH
RTN_VRMS
R2
1M
Y 1nF
L3
C5
VAC4
4
nc 2
2
Q1 NDF08N50ZG
to220decalD
sod123
D5 MMSD4148
1
LN3
1
R9
1M
RV2
eclat
RV1
eclat
3
8.5mH
VAC3
L4
Q3
2
BC808-25LT1
sot23
R6
LN2
R42
10K
1
RV3
eclat
D8
R28
1M
8.5mH
C12
R22
47u
R13
1M
R24
1K5
J104
X2 1uF
150K
150K
150K
R18
R19
R23
3
6
2K2
0.065 2 W 5%
res1000
275V
R12
1K
O_UVP
FB_PFC
R16 22K
R14 22K
150K
ZCD1_16
ZCD2_1
1
2
FB_PFC
150K
3
4
150K
6
BO_PFC
7
C21
2
7
220n
R29
120K
RELAY2
8
C13
C17
1nF
C19
C18
220p
R31
20K
680n
220n
R41
270K
R32
270K
NCP1631
ZCD2
ZCD1
FB
PFC-OK
Rt
DRV1
OSC
GND
Vcontrol
Vcc
Freq-Fall Back
BO
DRV2
Latch OFF
OVP/UVP
CS
VCC4
16
15
PFC-OK
R27
47k
13
Q6
12
11
D10
MMSD4148
sod123
10
9
C15
1
100n
sot23
BC856ALT1
C20
R37
1K
10n
R35
0
+
F1
FUSE 6A-250V
Gnd_Lug
CN402
LINE_NEUTRAL
90-264_VAC_INPUT
1
CN002
1
FG
FG
N
-
L006
1
cyld400l200c
D4
+
PFC_OUT2
RV5
1N4007
do41d
1mH
B72210P2321
rt100
2
F2
2
2
Q5
1
sot23
BC856ALT1
R38
1K
R36
10k
1
R40
10K
Q7
BC848ALT1
sot23
VAC_VSS1
3
C16
VAC1
D11 1N4007
do41d
3
R25
15K
POWER_BOOST
D12
MMSD4148
sod123
O_UVP
R34
10K
R33
39K
R26
2K2
14
10u 50V
CN001
4333-W05ST
2
sod123
R11
L5
SW1
RELAY MODULE
5
8
4
1
FG
INSTALL
1
R30
24K
MMSD4148
RELAY1
L
CN003
4324-07S
1
2
3
4
5
6
7
8
450V
DRIVE2
5
VAC2
450V
C7
10nF 500V
DRIVE1
IC1
R21
47u
C9
+
2
R3
R17
C8
+
R10
1M
47
47
RV4
eclat
3
R5
1M
R20
1M
PH9090NL
4
3
1
R15
1M
2
Q2 NDF08N50ZG
to220decalD
sod123
D6 MMSD4148
1
3
1
R43
Q4
2
10K
BC808-25LT1
sot23
R7
PFC3812QM
R8
1M
X2 100nF
275V
PH9090NL
5 nc
NTC 20R
R4
1M
MUR550APF
DO201d
4
*
RT1
D3
L3Q2
3
*
6
ZCD1
MUR550APF
DO201d
Heat_Sink
HS2
1
nc 5
PFC3812QM
1
Y 1nF
6
2 nc
10M 2W
C3
L2Q1
1
*
P
3
ZCD2 4
- 1
N
2 ~
PFC_OUT
D2
200uH
P
INSTALL
Heat_Sink
L2
2
1
+
3
1
4
~
3
3
HS1
N
VBD1
BD1
4R7 1W
PC001A
2
SFH817A
dip4_3
Standby_supply
cyld8e5c
+
C24
10 uF 450V
bulk
C26
10nF 500V
C25
4.7 uF 450V
bulk
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
Power_46 Pilot_1
A3
Dale Tittensor
EMI/ PFC
PCB
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-14
Jean-Paul Louvel
1 of 3
74
8 mm SLIM ECO Standby Power Supply
T100
SRW21EM-XXXX
NC
D101 1N4007
do41d
V-Stby
2
1
Key Pin-8
+
7
6
1
C102
R101
470µ 16V
1K
VCC2
PC100A
MMSD4148
sod123
2
1.25VREF
1
3
R105
10K
IC101
TLV431ASN1
sot23-3
2
INSTALL
GND_STDBY
HV Barrier
4
47µ 25V
V
6
1
F
u
0
7
4
1
J201
BAV21
do41d
C103
+
2
SFH817A
2
VCC0
100 n
ON-OFF Switch
"Optional"
e
t
a
n
r
e
t
l
A
R120 0
VCC1
R114
2K2
C106
PC100_DRV
D102
MMSD4148
sod123
R122 220K
R113 4K7
R104
10K
dip4_3
D105
PC200B
VS-Stby
1
VCC3
R102
30K
220nF
GND_STDBY
PC100A
2
1
INSTALL
N
1
VCC4
CN100
4324-02S
J200
470
C108
5
2
R121
4
D104
Q101 BC808-25LT1
3
sot23
L100
10uH
MBR3100
do201d
2
C101
10p 1KV
1
C100
1n 400V
P
R100a
33K 2W
D100
10
9
N
Standby_supply
P
3
R103 4K7
VS-Stby
SFH817A
3
dip4_3
IC100
NCP1053P44G
+
C104
10u 25 V
4
STDBY_FB
PC100B
2
C109
220p
SFH817A
1
VCC
GND
Control in
GND
D109
+
C105
47u 25 V
8
Regulation
V1
MMSD4148
sod123
STANDBY
7
D108
3
MMSD4148
sod123
3
dip4_3
GND
4
NC Power Drain
5
ZD101
R106
470
STDBY_MOS
R107
4K7
1
RELAY1
JT-xx jumpers are 0.75mm wire on the TOP layer.
JB-xx jumpers are 1206 SMT zero ohm on the BOTTOM layer.
---------------------------------------------------------Design (layout) Jumpers
Pattern Quantity Component
1206
40 JB1, JB2, JB3, JB4, JB5, JB6, JB7, JB8,
JB9, JB10, JB11, JB12, JB13, JB14, JB15,
JB16, JB17, JB18, JB19, JB20, JB21, JB22,
JB23, JB24, JB25, JB26, JB27, JB28, JB29,
JB30, JB31, JB32, JB33, JB34, JB35, JB36,
JB37, JB38, JB39, JB40, JB41, JB42, JB43
27 JT4, JT5, JT9, JT10, JT17, JT18, JT23,
JT24, JT25, JT26, JT28, JT29, JT31, JT32,
JT38, JT39, JT41, JT42, JT43, JT44, JT45,
JT49, JT50, JT51, JT51, JT56, JT59,
PC200A
D110
RELAY2
SFH817A
MMSD4148
sod123
JUMP-22MM
---------------------------------------------------------Schematic Jumpers are referenced from J100 upward.
Pattern Quantity Component
1206
1 J105
JUMPER-10MM
JUMP-22MM
Q100
BC858ALT1
2 sot23
R111
10K
ZD102
J202
sod123
R115 1K
R118
470
1
MMSZ4702T1 (15V)
VS2
R112
1K
Q103
sot23
BC848ALT1
R116 100
R117
4K7
C107
10nF
2
INSTALL
GND_REG
VS-Stby
9 JT3, JT7, JT12, JT13, JT14, JT16, JT34,
JT52, JT54,
26 JT1, JT2, JT6, JT8, JT11, JT15, JT19,
JT20, JT21, JT22, JT27, JT29, JT30,
JT33, JT35, JT36, JT37, JT40, JT46, JT47,
JT48, JT53, JT55, JT57, JT58, JT60,
R110
1K
D107
2
sod123
3
1
sod123
MMSD4148
POWER_OK
PC001B
SFH817A
dip4_3
3
JUMP-12_5MM
dip4_3
D106
MMSD4148
sod123
Q102
sot23
BC848ALT1
4
JUMP 10MM
RELAY2
RELAY1
MMSZ4690T1 (5V6)
VS1
R109
10K
D103
MMSD4148
sod123
R119
22K
GND_STDBY
POWER_OK
VS-Stby
CN101
4324-05S
5
4
3
2
1
Standby power and signal
To Signal processing board
STANDBY
12 J101, J102, J102b, J102c, J103, J104,
J200, J202, J300, J301, J302, J303
2 J201, J304
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
Power_46 Pilot_1
A3
Dale Tittensor
Standby SMPS PCB
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-14
Jean-Paul Louvel
2 of 3
75
8 mm SLIM QR Flyback Power Supply
T200
SRW4549EM-XXXX
3
PFC_OUT
13 T200-13
*
R200
33K 2W
SNUBR1
C200
10n 500V
SNUBR1
11 T200-11
*
NC 2
2
J302
C207
+
N
1
insert
1
insert
MUR180
T200-01 1
do41d
V2
2
J301
D201
1000u 16V
R205
1K
1
ZD200
(15V)
MMSZ4702T1
R206
sod123
BO
2
FB
BO
CS
VCC
Heat_Sink
HS3
1
7
100n
7
4
R211
1K
C211
C212
1n
220p
R249
4K7
GND
DRV
5
DRV_QRM
R217 27
FB
sot23
1
3
1
Heat_Sink
HS4
1
R220
47k
R219
4K7
1000u 16V
3
1
2
R222
4K7
C224
470u 16V
R223
1K
Y 1nF
4
1
GND_POWER_2
+
3
dip4_3
VS2
10u 50V
R245 0
R203 33k
R225 1K
V_123
C227 0R / Jumper
BO
PFC-OK
D211
MMSD4148
sod123
Regulation
Gnd_Lug
CN404
C216
SFH817A
+
Q205
BC858ALT1
sot23
1
VS1
cyld400l200c
MBRF20L80CTG
C225
2
Q204
BC808-25LT1
10uH
2
C219
Gnd_Lug
CN403
R221
0.47R 2W
res1000
L202
1
+
3
C218
100p 1KV
3K3
VCC4
2
D210
to220
CS
R209 100
6
*
sod123
MMSD4148
R218
C215
T200-67
1000u 16V
V1
220
MJD200
R216
DPAK
220
8
DRV_Q203
100n
PC101B
Q203
STP5NK80ZFP
to220decalD
C221
+
P
PWM_VCC
6
D209
C210
68p
ZD201
MMSZ4692T1 (6V8)
sod123
Q202
R215
9
C214
*
3
CS
C209
470u 16V
1000u 16V
P
R213 470
C213
8
330p
FB
V1
10
*
C205
+
P
CT
*
3
D207
to220
MBRF20L100CTG
N
ZCD
C217
47u 25V
VS2
+
N
1
4
+
2
sod123
IC200
NCP1379
MMSD4148
12 T200-12
220
BAV21
do41d
D206
MMSD4148
470k
5
N
D203
sod123
T200-05
10uH
cyld400l200c
N
VCC3
L201
1
2
P
R207
N
D205
P
R251
33K 2W
P
R252
33K 2W
V2
R226 750
MMSD4148
sod123
V1
PC101A
1
SFH817A
dip4_3
2
R227
1K
VS-Stby
R237
10K
C230
470nF
1
VS2
R231 16K2
VS1
MMSD4148
sod123
3 Q207
BC858ALT1
sot23
2
VS_123
VS1
2_5VREF
1
R232 6K19
VS2
R238
10K
D219
CN201
4324-11S
Flyback power to
11
10
Signal processing
9
and Audio board
8
7
6
5
4
3
2
1
0R / Jumper
sod123
P
to92d
2
TL431ACLPRPG
Backlight
controller
supply to
Backlight
board
D217
C228
470nF
PC101_DRV
IC201 3
VS1
R236
470
D215
R214 10k
CN202
4324-03S
1
2
3
R233
2K4
N
+
C232
470u 16V
D221
Regulation
GND_REG
R228 100
BAT54T1
sod123
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
Power_46 Pilot_1
A3
Dale Tittensor
Flyback SMPS PCB
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-14
Jean-Paul Louvel
3 of 3
76
8 mm SLIM PWM Flyback Power Supply
T200
SRW4549EM-XXXX
3
PFC_OUT
13 T200-13
*
*
NC 2
11 T200-11
J301
2
D201
MUR180
T200-01 1
do41d
J302
V2
insert
C207
+
N
1
insert
R207
VCC3
T200-05
5
220
4
sod123
+
3
CS
SS
BO
Vcc
CS
DRV
7
6
2
DRV_FLY
C234
4
C235
RT
GND
10k
1n
220p
C237
1u 50V
C236
100n
3
R220
47k
7
6
2
1
C225
P
R219
4K7
3
Q205
BC858ALT1
sot23
1
2
D211
MMSD4148
sod123
R222
4K7
C224
470u 16V
R223
1K
Regulation
Gnd_Lug
CN404
1
VS1
+
1000u 16V
MBRF20L80CTG
to220
10uH
2
cyld400l200c
C219
+
Gnd_Lug
CN403
R221
0.47R 2W
res1000
L202
1
Heat_Sink
HS4
1
3
C218
100p 1KV
2
Q204
BC808-25LT1
D210
1000u 16V
V1
220
MJD200
DPAK
R216
220
T200-67
C221
+
Y 1nF
4
C225a
1
GND_POWER_2
Y 1nF
dip4_3
3
SFH817A
Q203_S
sot23
1
FB
PC101B
*
sod123
MMSD4148
3K3
C216
10u 50V
ZD201
MMSZ4692T1 (6V8)
sod123
Q202
R215
8
Q203_G
R218
+
C209
470u 16V
1000u 16V
VS2
R245 0
R225 1K
V_123
C227 0R / Jumper
PC101A
PC101A 1
VS1
R236
470
V2
D215
V1
MMSD4148
sod123
R226 750
dip4_3
2
VS-Stby
R227
1K
R237
10K
C230
470nF
1
VS2
PC101_DRV
R231 16K2
VS1
to92d
2
TL431ACLPRPG
3 Q207
BC858ALT1
sot23
2
VS_123
2_5VREF
1
MMSD4148
sod123
R232 6K19
VS2
R238
10K
D219
IC201 3
Backlight
controller
supply to
Backlight
board
D217
C228 470nF
SFH817A
CN202
4324-03S
1
2
3
0R / Jumper
sod123
VS1
CN201
4324-11S
Flyback power to
11
10
Signal processing
9
and Audio board
8
7
6
5
4
3
2
1
P
1n
R248
100K
Q203
STP5NK80ZFP
to220decalD
CS
+
R250
15K
D209
DRV_Q203
5
V1
+
R233
2K4
N
R214
*
*
10K
R247
27
C233
*
9
Q208
BC858ALT1
sot23
3
R246
1
8
C205
+
P
2
FB
10
MBRF20L100CTG
to220
N
1
FB
3
Heat_Sink
HS3
1
470
IC202
NCP1252
VS2
C217
47u 25V
R213
VCC4
12
N
BO
PFC-OK
2
+
P
R209 100
10uH
cyld400l200c
N
R203 33k
L201
1
2
N
BAV21
do41d
D207
N
ZD200
(15V)
MMSZ4702T1
1
P
D205
1000u 16V
P
C200
10n 500V
SNUBR1
P
R200
33K 2W
2
R251
33K 2W
1
R252
33K 2W
C232
470u 16V
D221
Regulation
GND_REG
R228 100
BAT54T1
sod123
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
ON-Power-46"
A3
Dale Tittensor
PWM Flyback SMPS
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-15
Jean-Paul Louvel
3 of 3
77
8 mm SLIM BOM with QR Flyback
Position
(note)
BD01
Screw1
HS1
C001
C003
C004
C005
C007
C008
C008a
C009
C009a
C012
C013
C015
C016
C016a
C017
C018
C019
C020
C021
C024
C024a
C025
C026
C100
C101
C102
C102a
C103
C103a
C104
C104a
C105
C105a
C106
C107
C108
Component Type
Value
Rating
Pkg / Dimensions
Bridge Rectifier
Screw
Heat Sink
CFS
CCS-Y1
CCS-Y1
CPMX-X2
Ceramic Cap
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
CPMX-X2
Ceramic Chip Cap
Ceramic Chip Cap
Electrolytic 105°C
Electrolytic 105°C
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Ceramic Cap
Ceramic Cap
Ceramic Cap
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
8A-600V
8A-600V
470 nF
1 nF
1 nF
100 nF
10 nF
47 uF
39 uF
47 uF
39 uF
1 uF
680 nF
100 nF
10 uF
10 uF
1 nF
220 pF
220 nF
10 nF
220 nF
10 uF
10 uF
4.7 uF
10 nF
1 nF
10 pF
470 uF
470 uF
47 uF
47 uF
10 uF
10 uF
47 uF
47 uF
100 nF
10 nF
220 nF
3mm x0.5p x8mm thread length
Length 120mm Height 7mm
450V
Radial 15mm
400V / 4KV Radial 10mm
400V / 4KV Radial 10mm
275V
Radial 15mm
500V
Radial 5mm
450V
Radial 5mm D10x45mm 0.44A
450V
Radial 5mm D10x50mm 0.375A
450V
Radial 5mm D10x45mm 0.44A
450V
Radial 5mm D10x50mm 0.375A
275V
Radial 22.5mm
10V
0805
25V
0805
50V
Radial 5mmx11mm
50V
Radial 5mmx11mm
10V
0805
10V
0805
10V
0805
10V
0805
10V
0805
450V
Radial 5mm D10mm H20mm
450V
Radial 5mm D10mm H20mm
450V
Radial 5mm D10mm H12.5mm
500V
Radial 5mm
400V
Radial 5mm
1 kV
Radial 5mm
16V
Radial 5mm D10mmx12.5mm 1A
16V
Radial 5mm D10mmx12.5mm 1A
25V
Radial 5mm D8mm
25V
Radial 5mm D8mm
50V
Radial 5mmx11mm
50V
Radial 5mmx11mm
25V
Radial 5mm D8mm
25V
Radial 5mm D8mm
25V
0805
10V
0805
10V
0805
Reference
Supplier
GBU806
W950
TP209ST,120,7.0,NA--,02BB
MES474K450VDC
5SE102MT402A97E
5SE102MT402A97E
HQX104K275I04SANYAY
3x10
450QXW47M10X45
EKXJ451BC390MJ50S
450QXW47M10X45
EKXJ451BC390MJ50S
HQX5x10K275N04SANYAY
4x68
4x10
50YXA10M5X11
EKMG500Exx100ME11D
2x10
1x22
4x22
3x10
4x22
450PY00010M10X20
EKMQ451ELL100MJC5S
400YXA3R3M10X12.5
3x10
2x10
0x10
16ZL470M10X12.5
EKZE160Exx471MJC5S
25YXA47M5X11
EKMG1x10Exx470ME11D
50YXA10M5X11
EKMG500Exx100ME11D
25YXA47M5X11
EKMG1x10Exx470ME11D
4x10
3x10
4x22
Taiwan Semiconductor
Columbia-Staver
Columbia-Staver
Joey Electronics
SUCCESS
SUCCESS
Shanghai Ultra Tech (UTX)
SUCCESS
Rubycon
Nippon Chemicon
Rubycon
Nippon Chemicon
Shanghai Ultra Tech (UTX)
Synton-Tech Corporation.
Synton-Tech Corporation.
Rubycon
Nippon Chemi Con
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Rubycon
Nippon Chemi Con
Rubycon
SUCCESS
SUCCESS
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
78
Position
(note)
C109
C200
C205
C205a
C207
C207a
C209
C209a
C210
C211
C212
C213
C214
C215
C216
C216a
C217
C217a
C218
C219
C219a
C221
C221a
C224
C224a
C225
C227
C228
C230
C232
C232a
CN001
CN002
CN003
CN100
CN101
CN200
CN201
CN202
CN401
Component Type
Value
Rating
Pkg / Dimensions
Reference
Supplier
Ceramic Chip Cap
Ceramic Cap
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Electrolytic 105°C
Ceramic Cap
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
CCS-Y1
Carbon Chip Resistor
Ceramic Chip Cap
Ceramic Chip Cap
Electrolytic 105°C Low Z
Electrolytic 105°C Low Z
Mains Connector
GND Connector
Signal conector
Signal conector
Signal conector
220 pF
10 nF
1000 uF
1000 uF
1000 uF
1000 uF
470 uF
470 uF
68 pF
1 nF
220 pF
330 pF
100 nF
100 nF
10 uF
10 uF
47 uF
47 uF
100 pF
1000 uF
1000 uF
1000 uF
1000 uF
470 uF
470 uF
1 nF
0R0
470 nF
470 nF
470 uF
470 uF
4333-W05RT
To be defined
4324- 8R
4324- 2R
4324- 5R
10V
500V
16V
16V
16V
16V
16V
16V
10V
10V
10V
10V
25V
25V
50V
50V
25V
25V
1 kV
16V
16V
16V
16V
16V
16V
400V / 4KV
0805
Radial 5mm
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx12.5mm 1A
Radial 5mm D10mmx12.5mm 1A
0805
0805
0805
0805
0805
0805
Radial 5mmx11mm
Radial 5mmx11mm
Radial 5mm D8mm
Radial 5mm D8mm
Radial 5mm
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx20mm 1.82A
Radial 5mm D10mmx12.5mm 1A
Radial 5mm D10mmx12.5mm 1A
Radial 10mm
0805
0805
0805
Radial 5mm D10mmx12.5mm 1A
Radial 5mm D10mmx12.5mm 1A
Right Angle 15mm with 2 ext. pins
x
Right Angle 2.5mm
Right Angle 2.5mm
Right Angle 2.5mm
1x22
3x10
16ZL1000M10X20
EKZE160Exx102MJ20S
16ZL1000M10X20
EKZE160Exx102MJ20S
16ZL470M10X12.5
EKZE160Exx471MJC5S
0x68
2x10
1x22
1x33
4x10
4x10
50YXA10M5X11
EKMG500Exx100ME11D
25YXA47M5X11
EKMG1x10Exx470ME11D
1x10
16ZL1000M10X20
EKZE160Exx102MJ20S
16ZL1000M10X20
EKZE160Exx102MJ20S
16ZL470M10X12.5
EKZE160Exx471MJC5S
5SE2x10MT402A97E
0x00
4x47
4x47
16ZL470M10X12.5
EKZE160Exx471MJC5S
4333-W05RT
x
4324- 8R
4324- 2R
4324- 5R
Synton-Tech Corporation.
Signal conector
Signal conector
Gnd Lug
4324-11R
4324- 3R
tbd
Right Angle 2.5mm
Right Angle 2.5mm
3.175mm x 8mm
4324-11R
4324- 3R
10V
10V
16V
16V
250V 5A
x
8 pins
2 pins
5 pins
11 pins
3 pins
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
SUCCESS
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
Rubycon
Nippon Chemi Con
SUCCESS
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Rubycon
Nippon Chemi Con
LEAMAX Enterprise
LEAMAX Enterprise
LEAMAX Enterprise
LEAMAX Enterprise
LEAMAX Enterprise
LEAMAX Enterprise
79
Position
(note)
CN402
CN403
CN404
D002
D003
D004
D005
D006
D008
D010
D011
D012
D100
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
D201
D203
D205
D206
D207
Screw4
HS4
D209
D210
Screw5
D211
D215
D217
D219
D221
F001
F002
Component Type
Value
Rating
Gnd Lug
Gnd Lug
Gnd Lug
Diode Ultra Fast
Diode Ultra Fast
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode Fast
Diode
Diode Fast
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode Fast
Diode
Diode Fast
Diode
Diode Dual Schottky
Screw
Heat Sink
Diode
Diode Dual Schottky
Screw
Diode
Diode
Diode
Carbon Chip Resistor
Diode Schottky
Fuse
HV Fuse resistance
tbd
tbd
tbd
MUR550APF
MUR550APF
1N4007
MMSD4148
MMSD4148
MMSD4148
MMSD4148
1N4007
MMSD4148
MBR3100
1N4007
BAV21
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MUR180
MMSD4148
BAV21
MMSD4148
MBRF20L100CTG
520V 5A
520V 5A
1000V 1A
100V 0.2A
100V 0.2A
100V 0.2A
100V 0.2A
1000V 1A
100V 0.2A
100V 3A
1000V 1A
600V 1A
100V 0.2A
100V 0.2A
100V 0.2A
100V 0.2A
100V 0.2A
100V 0.2A
100V 0.2A
100V 0.2A
800V 1A
100V 0.2A
600V 1A
100V 0.2A
100V 20A
MMSD4148
MBRF20L80CTG
100V 0.2A
80V 20A
MMSD4148
MMSD4148
MMSD4148
0R0
BAT54T 1
6A
4.7R 1W
100V 0.2A
100V 0.2A
100V 0.2A
30V 0.2A
250V
450V
Pkg / Dimensions
3.175mm x 8mm
3.175mm x 8mm
3.175mm x 8mm
DO-201 TOP Manual Axial 22.5mm
DO-201 TOP Manual Axial 22.5mm
DO-41 Axial 12.5mm
SOD-123
SOD-123
SOD-123
SOD-123
DO-41 Axial 12.5mm
SOD-123
DO-201 TOP Manual Axial 22.5mm
DO-41 Axial 12.5mm
DO-41 Axial 12.5mm
SOD-123
SOD-123
SOD-123
SOD-123
SOD-123
SOD-123
SOD-123
SOD-123
DO-41 Axial 12.5mm
SOD-123
DO-41 Axial 12.5mm
SOD-123
TO-220AB
3mm x0.5p x8mm thread length
Length 80mm Height 7mm
SOD-123
TO-220AB
3mm x0.5p x8mm thread length
SOD-123
SOD-123
SOD-123
1206
SOD-123
Axial 5x20mm
Radial 5mm D10
Reference
Supplier
MUR550APF
MUR550APF
1N4007
MMSD4148
MMSD4148
MMSD4148
MMSD4148
1N4007
MMSD4148
MBR3100
1N4007
BAV21
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MMSD4148
MUR180
MMSD4148
BAV21
MMSD4148
MBRF20L100CTG
ON Semiconductor
ON Semiconductor
PANJIT
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
PANJIT
ON Semiconductor
ON Semiconductor
PANJIT
PANJIT
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
TP209ST,80.0,7.0,NA,--,02B
MMSD4148
MBRF20L80CTG
Columbia-Staver
ON Semiconductor
ON Semiconductor
MMSD4148
MMSD4148
MMSD4148
0x00
BAT54T1
UBM-A006
FRN 100S J 4R7 FK
ON Semiconductor
ON Semiconductor
ON Semiconductor
Synton-Tech Corporation.
ON Semiconductor
CONQUER
Synton-Tech Corporation.
80
Position
(note)
IC001
IC100
IC101
IC200
IC201
J101
J104
J200
J201
J202
J301
J302
L002
L003
L004
L005
L100
L201
L202
PC001
PC100
PC101
PC200
Q001
Screw2
HS2
Q002
Screw6
Q003
Q004
Q005
Q006
Q007
Q100
Q101
Q102
Q103
Component Type
Value
PFC Controller
44Khz GTO Switch-Reg.
Voltage Ref.
QR Controller
Voltage Ref.
0.75mm wire
0.75mm wire
0.75mm wire
0.75mm wire
0.75mm wire
0.75mm wire
0.75mm wire
PFC Coil
PFC Coil
Common Mode Filter
Common Mode Filter
Inductance filter
Inductance filter
Inductance filter
Opto-coupler
Opto-coupler
Opto-coupler
Opto-coupler
Power MOS
Screw
Heat Sink
Power MOS
Screw
PNP transistor
PNP transistor
PNP transistor
PNP transistor
NPN
PNP transistor
PNP transistor
NPN
NPN
NCP1631
NCP1053P44G
TLV431A
NCP1379
TL431ACLPRPG
0R0
0R0
0R0
0R0
0R0
0R0
0R0
220uH
220uH
8.5mH
8.5mH
10uH
10uH
10uH
SFH817A
SFH817A
SFH817A
SFH817A
NDF08N50ZG
NDF08N50ZG
BC808-25LT1
BC808-25LT1
BC856ALT1
BC856ALT1
BC848ALT1
BC858ALT1
BC808-25LT1
BC848ALT1
BC848ALT1
Rating
0.01
0.01
3.3A
3.3A
5A
5A
5A
500V 8A
500V 8A
Pkg / Dimensions
Reference
Supplier
SOIC-16
PDIP-8
SOT-223
SOIC-8
TO-92
Axial 10mm
Axial 10mm
Axial 10mm
Axial 22mm
Axial 10mm
Axial 10mm
Axial 10mm
TOP Manual
TOP Manual
TOP Manual
TOP Manual
Radial 5mmD10mmH8mm
Radial 5mmD10mmH8mm
Radial 5mmD10mmH8mm
DIP-4
DIP-4
DIP-4
DIP-4
TO220FP
3mm x0.5p x8mm thread length
Length 120mm Height 7mm
TO220FP
3mm x0.5p x8mm thread length
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
NCP1631
NCP1053P44G
TLV431ASN1
NCP1379
TL431ACLPRPG
0x00
0x00
0x00
0x00
0x00
0x00
0x00
PFC3812QM-221k04B-01
PFC3812QM-221k04B-01
PH9090NL
PH9090NL
744732100
744732100
744732100
SFH817A
SFH817A
SFH817A
SFH817A
NDF08N50ZG
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
TDK
TDK
PULSE
PULSE
WURTH ELEKTRONIK
WURTH ELEKTRONIK
WURTH ELEKTRONIK
SHARP
SHARP
SHARP
SHARP
ON Semiconductor
TP209ST,120,7.0,NA,--02B
NDF08N50ZG
Columbia-Staver
ON Semiconductor
BC808-25LT1
BC808-25LT1
BC856ALT1
BC856ALT1
BC848ALT1
BC858ALT1
BC808-25LT1
BC848ALT1
BC848ALT1
ON
ON
ON
ON
ON
ON
ON
ON
ON
Semiconductor
Semiconductor
Semiconductor
Semiconductor
Semiconductor
Semiconductor
Semiconductor
Semiconductor
Semiconductor
81
Position
(note)
Q202
Q203
Screw3
HS3
Q204
Q205
Q206
Q207
R001
R002
R003A
R004
R005
R006
R007
R008
R009
R010
R011
R012
R013
R014
R015
R016
R017
R018
R019
R020
R021
R022
R023
R024
R025
R026
R027
R028
R029
R030
R031
Component Type
Value
Rating
Pkg / Dimensions
Reference
Supplier
Power NPN transistor
Power MOS
Screw
Heat Sink
PNP transistor
PNP transistor
NPN
PNP transistor
Carbon Chip Resistor
Carbon Chip Resistor
Wirewound Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
MJD200
STP8NK80ZFP
25V 5A
800V 5A
DPAK
TO220FP
3mm x0.5p x8mm thread length
Length 40mm Height 7mm
SOT-23
SOT-23
SOT-23
SOT-23
0805
0805
TOP Manual Axial 22.5mm
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
MJD200
STP8NK80ZFP
ON Semiconductor
STMicroelectronics
TP207ST,40.0,7.0,NA,--,02B
BC808-25LT1
BC858ALT1
BC848ALT1
BC858ALT1
6x10
6x10
1R65
6x10
6x10
0x47
0x47
6x10
6x10
6x10
2x22
2x10
6x10
3x22
6x10
3x22
4x15
4x15
4x15
6x10
4x15
4x15
4x15
2x15
3x15
2x22
3x47
6x10
4x12
3x24
3x20
Columbia-Staver
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
BC808-25LT1
BC858ALT1
BC848ALT1
BC858ALT1
1M
1M
0.065 5%
1M
1M
47
47
1M
1M
1M
2.2K
1K
1M
22K
1M
22K
150K
150K
150K
1M
150K
150K
150K
1.5K
15K
2.2K
47K
1M
120K
24K
20K
2W
82
Position
(note)
R032
R033
R034
R035
R036
R037
R038
R040
R041
R042
R043
R100a
R101
R102
R103
R104
R105
R106
R107
R109
R110
R111
R112
R113
R114
R115
R116
R117
R118
R119
R120
R121
R122
R200
R203
R205
R206
Notes:
Component Type
Value
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Metal Film Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Metal Film Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
270K
39K
10K
0R0
10K
1K
1K
10K
270K
10K
10K
33K 5%
1K
30K
4.7K
10K
10K
470
4.7K
10K
1K
10K
1K
4.7K
2.2K
1K
100
4.7k
470
22K
0R0
470
220K
33K 5%
33K
1K
470K
Rating
2W
2W
Pkg / Dimensions
Reference
Supplier
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
TOP Manual Axial 22.5mm
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
TOP Manual Axial 22.5mm
0805
0805
0805
4X27
3x39
3x10
0x00
3x10
2x10
2x10
3x10
4x27
3x10
3x10
3x33
2x10
3x30
2x47
3x10
3x10
1x47
2x47
3x10
2x10
3x10
2x10
2x47
2x22
2x10
1x10
2x47
1x47
3x22
0x00
1x47
4X22
3x33
3x33
2x10
4x47
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Resistor tolerances are +/- 5% unless noted otherwise
Capacitor tolerances are +/- 10% unless noted otherwise
Electrolytic capacitor tolerances are +/- 20% unless noted otherwise
83
Position
(note)
R207
R209
R211
R213
R214
R215
R216
R217
R218
R219
R220
R221
R222
R223
R225
R226
R227
R228
R231
R232
R233
R236
R237
R238
R245
R249
R251
R252
R255
RT1
RV5
SW1
T100
T200
ZD101
ZD102
ZD200
ZD201
Notes:
Component Type
Value
Rating
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Wirewound Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Metal Film Resistor
Metal Film Resistor
Metal Film Resistor
Thermistor
Varistor
Relay
Standby Transformer
Switch Mode Transformer
Diode, Zener
Diode, Zener
Diode, Zener
Diode, Zener
220
100
1K
470
10K
220
220
27
3.3K
4.7K
47K
0.47R 5%
4.7K
1K
1K
750
1K
100
16.2K 1%
6.19K 1%
2.40K 1%
1K
10K
10K
0R0
4.7K
33K 5%
33K 5%
10M 5%
20 ohm
1206
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
2W
TOP Manual
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
2W
TOP Manual
2W
TOP Manual
2W
TOP Manual
3W
TOP Manual
420V
TOP Manual
10A / 250V TOP Manual
EPC17
TOP Manual
EEM
TOP Manual
5.6V
SOD-123
15V
SOD-123
15V
SOD-123
6.8V
SOD-123
5V 50mA
2.5mH
680uH
MMSZ4690T1
MMSZ4702T1
MMSZ4702T1
MMSZ4692T1
Pkg / Dimensions
Axial 22.5mm
Axial 22.5mm
Axial 22.5mm
Axial 22.5mm
Rad 5mm
Rad 7.5mm
Reference
Supplier
0x22
1x10
2x10
1x47
3x10
1x22
1x22
0x27
2x33
2x47
3x47
0R47
2x47
2x10
2x10
1X75
2x10
1x10
2x162
1x619
1x249
2x10
3x10
3x10
0x00
2x47
3x33
3x33
6x10
B57153S0200M000 20R
B72210P2321K101
HF36F/005-HSLT
SRW 2125EM-X03H015
SRW 4549EM-X01H017
MMSZ4690T1
MMSZ4702T1
MMSZ4702T1
MMSZ4692T1
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
Synton-Tech Corporation.
EPCOS
EPCOS
HONGFA
TDK
TDK
ON Semiconductor
ON Semiconductor
ON Semiconductor
ON Semiconductor
Resistor tolerances are +/- 5% unless noted otherwise
Capacitor tolerances are +/- 10% unless noted otherwise
Electrolytic capacitor tolerances are +/- 20% unless noted otherwise
84
Position
(note)
PCB1
RELAY_MOD
ULE_1
JB1, JB2,
JB3,
JB4, JB5,
JB6,
JB7, JB8,
JB9, JB10,
JB11, JB12,
JB13, JB14,
JB15, JB16,
JB17, JB18,
JB19, JB20,
JB21, JB22,
JB23, JB24,
JB25, JB26,
JB27, JB28,
JB29, JB30,
JB31, JB32,
JB33, JB34,
JB35, JB36,
JB37, JB38,
JB39, JB40,
JB41, JB42,
JB43
Component Type
Value
Rating
Pkg / Dimensions
Reference
Supplier
1206
0x00
Synton-Tech Corporation.
8mm_Power46_PCB
8mm_Relay_PCB
Carbon Chip Resistor
0R0
85
Position
(note)
JT4, JT5,
JT9, JT10,
JT17, JT18,
JT23, JT24,
JT25, JT26,
JT28, JT29,
JT31, JT32,
JT38, JT39,
JT41, JT42,
JT43, JT44,
JT45, JT49,
JT50, JT51,
JT51, JT56,
JT59
JT3, JT7,
JT12, JT13,
JT14, JT16,
JT34, JT52,
JT54
JT1, JT2,
JT6,
JT8, JT11,
JT15, JT19,
JT20, JT21,
JT22, JT27,
JT29, JT30,
JT33, JT35,
JT36, JT37,
JT40, JT46,
JT47, JT48,
JT53, JT55,
JT57, JT58,
JT60
Notes:
Component Type
Value
0.75mm wire
Rating
Pkg / Dimensions
Reference
Supplier
0R0
Axial 10mm
0x00
Synton-Tech Corporation.
0.75mm wire
0R0
Axial 12.5mm
0x00
Synton-Tech Corporation.
0.75mm wire
0R0
Axial 22mm
0x00
Synton-Tech Corporation.
Resistor tolerances are +/- 5% unless noted otherwise
Capacitor tolerances are +/- 10% unless noted otherwise
Electrolytic capacitor tolerances are +/- 20% unless noted otherwise
86
Flyback BOM modifications from QR NCP1379 to PWM NCP1252
(Same for both 8 and 13 mm)
Section
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
QR Flyback
Position
C210
C211
C212
C213
C214
C215
D203
D206
IC200
R205
R206
R211
R217
R249
Component Type
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Diode
Diode
QR Controller
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Value
68 pF
1 nF
220 pF
330 pF
100 nF
100 nF
MMSD4148
MMSD4148
NCP1379
1K
470K
1K
27
4.7K
Rating
10V
10V
10V
10V
25V
25V
100V 0.2A
100V 0.2A
Pkg / Dimensions
0805
0805
0805
0805
0805
0805
SOD-123
SOD-123
SOIC-8
0805
0805
0805
0805
0805
Reference
0x68
2x10
1x22
1x33
4x10
4x10
MMSD4148
MMSD4148
NCP1379
2x10
4x47
2x10
0x27
2x47
Supplier
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
ON Semiconductor
ON Semiconductor
ON Semiconductor
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
C233
C234
C235
C236
C237
IC202
Q208
R246
R247
R248
R250
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Ceramic Chip Cap
Electrolytic 105°C
Fix Frequency Controller
PNP transistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
Carbon Chip Resistor
1 nF
1 nF
220 pF
100 nF
1 uF
NCP1252
BC858ALT1
10K
27
10K
10K
10V
10V
10V
25V
50V
0805
0805
0805
0805
Radial 5mmx11mm
SOIC-8
SOT-23
0805
0805
0805
0805
2x10
2x10
1x22
4x10
6x10
NCP1252ADR2G
BC858ALT1
3x10
0x27
3x10
3x10
Synton-T ech
Synton-T ech
Synton-T ech
Synton-T ech
Flyback
Flyback
Flyback
Flyback
Flyback
Flyback
Flyback
Flyback
Flyback
Flyback
Flyback
Notes:
Corporation.
Corporation.
Corporation.
Corporation.
ON Semiconductor
ON Semiconductor
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Synton-T ech Corporation.
Resistor tolerances are +/- 5% unless noted otherwise
Capacitor tolerances are +/- 10% unless noted otherwise
Electrolytic capacitor tolerances are +/- 20% unless noted otherwise
87
13 mm Mains filters and PFC schematic
VRMS
L2
6
5
4
VBD1
BD1
11
3
D2
L2Q1
PFC_OUT
2
*
ZCD2
4
~
7
8
9
200uH
*
MUR550APF
DO201d
EFD-30
Key Pins-3,10
2 ~
- 1
C1
0.47uF
450V
GBU806
Gnd_Lug
CN401
C4
RTN_VRMS
C5
2
2
R9
1M
RV2
eclat
R15
1M
3
L4
8.7mH
2
C6
68u
CN003
4324-07S
1
2
3
4
5
6
7
8
450V
+
68u
450V
R13
1M
R7
3
4
VAC3
C7
10nF 500V
10K
Q4
BC808-25LT1
sot23
10K
Q3
BC808-25LT1
sot23
R6
R10
1M
R43
1
R42
1
RV1
eclat
C8
+
2
Q1 NDF8N50ZG
to220decalD
sod123
D5 MMSD4148
1
LN3
R5
1M
Q2 NDF8N50ZG
to220decalD
sod123
D6 MMSD4148
1
3
CFS28
EFD-30
R8
1M
R4
1M
MUR550APF
DO201d
Key Pins-3,10
X2 100nF
275V
1
D3
L3Q2
2
VAC4
PFC_OUT2
2
*
ZCD1
R2
1M
Y 1nF
7
8
9
200uH
*
11
1
GND_STDBY
Y 1nF
NTC 20R
L3
6
5
4
R1
1M
3
C3
RT1
Heat_Sink
HS2
1
+
3
Heat_Sink
HS1
1
Backlight
Input
Power and
Signal
R24
1K5
47
47
LN2
CFS28
1
R20
1M
2
RV3
eclat
RV4
eclat
R30
24K
D8
R28
1M
INSTALL
1
2
sod123
3
2K2
R12
R16
0.065 2 W 5%
res1000
1K
O_UVP
R18
150K
R21
R14
R19
150K
R22
22K
150K
FB_PFC
22K
ZCD1_10
IC1
ZCD1_1
1
2
FB_PFC
150K
3
R23
150K
4
150K
5
6
RELAY1
BO_PFC
RELAY2
VAC2
7
1
2
4
C21
220n
SW1
C17
3
1nF
RELAY SPST
C19
C18
220p
LINE_NEUTRAL
R29
120K
8
C13
R31
20K
680n
R41
270K
16
ZCD1
FB
PFC-OK
Rt
DRV1
OSC
BO
Q6
12
11
DRV2
sot23
100n
D10
MMSD4148
sod123
9
CS
1
C15
10
Latch OFF
OVP/UVP
R27
47k
13
Vcc
Freq-Fall Back
PFC-OK
BC856ALT1
R25
15K
Q5
1
sot23
BC856ALT1
POWER_BOOST
D12
MMSD4148
sod123
C20
R37
1K
10n
R35
0
R34
10K
R33
39K
R26
2K2
14
GND
Vcontrol
VCC4
15
O_UVP
R32
270K
220n
NCP1631
ZCD2
2
R17
275V
3
X2 1uF
R38
1K
+
R36
10k
1
C12
C16
10u 50V
Q07
BC848ALT1
R40
10K
PC001A
2
R11
8.7mH
2
R3
L5
3
4
VAC2
J106
MMSD4148
SFH817A
D11 1N4007
do41d
LINE_NEUTRAL
Gnd_Lug
CN402
90-264_VAC_INPUT
1
CN002
1
L
FG
FG
FG
N
???
CN001
4333-W05ST
VAC_VSS1
1
L006
2
F2
4R7 1W
Standby_supply
1mH
F1
FUSE 6A-250V
D4
C24
RV5
PFC_OUT2
1N4007
do41d
B72210P2321
rt100
C26
+
cyld8e5c
C25
+
10 uF 450V
bulk
10nF 500V
4.7 uF 450V
bulk
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
13 mm 46 Power
A3
Dale Tittensor
EMI/ PFC Pilot
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-18
Jean-Paul Louvel
1 of 3
88
13 mm ECO Standby Power Supply schematic
T100
D100
C101
10p 1KV
1
4
D101 1N4007
do41d
SNUBR2
7
6
5
L100
V-Stby
MBR3100
do201d
1
+
10uH
C102
R101
CN100
4324-02S
1
2
470µ 16V
1K
R121
470
C108
J100
INSTALL
R102
220nF
GND_STDBY
30K
1
PC100A
2
2
C100
220p 400V
N
R100
47K 1/2W
res500d
9
8
P
3
Standby_supply
1
750871014
PC100A
1.25VREF
1
D102
R120 0
VCC1
MMSD4148
sod123
VCC0
1
BAV21
do41d
R114
2K2
J103
2
C103
47µ 25V
N
2
D105
R105
10K
IC101
TLV431ASN1
sot23-3
INSTALL
GND_STDBY
HV Barrier
4
VS-Stby
D109 MMSD4148
sod123
3
PC200B
100 n
+
2
1
MMSD4148
sod123
R113 4K7
C106
PC100_DRV
R104
10K
SFH817A
VCC3
3
VCC2
P
D104
Q101 BC808-25LT1
3
2
sot23
VCC4
RELAY1
D108 MMSD4148
sod123
RELAY2
D110 MMSD4148
sod123
V1
SFH817A
Regulation
STANDBY
R122 220K
1
2
C109
GND
Control in
GND
8
C105
47u 25 V
PC200A
3
1
R110
1K
D107
5
STDBY_MOS
R112
1K
R115 1K
R118
470
1
sod123
Q103
sot23
BC848ALT1
R116 100
R117
4.7K
J104
C107
10nF
2
INSTALL
GND_REG
VS-Stby
4
NC Power Drain
POWER_OK
PC001B
SFH817A
3
4
MMSZ4702T1 (15V)
VS2
Q100
BC858ALT1
sot23
R111
10K
sod123
MMSD4148
GND
Q102
sot23
BC848ALT1
ZD102
2
R109
10K
D103
MMSD4148
sod123
D106
MMSD4148
sod123
SFH817A
7
3
220p
VCC
R107
4.7K
2
4
STDBY_FB
SFH817A
R106
470
+
3
C104
10u 25 V
PC100B
sod123
IC100
NCP1053P44G
+
MMSZ4690T1 (5V6)
VS1
R103 8.2K
1
STDBY_VCC
ZD101
R119
22K
GND_STDBY
POWER_OK
VS-Stby
STANDBY
CN101
4324-05S
5
4
3
2
1
Standby power and signal
To Signal processing board
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
13 mm 46 Power
A3
Dale Tittensor
Standby SMPS Pilot
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-18
Jean-Paul Louvel
2 of 3
89
13 mm QR Flyback Power Supply schematic
T200
750875731
1
PFC_OUT
C200
10n 500V
T200-11
D201
+
D205
R207 100
12
C212
1n
220p
R249
4K7
GND
DRV
5
DRV_QRM
R217 27
10
9
*
2
sot23
1
R220
47k
N
N
P
N
+
+
C220
470u 16V
470u 16V
Heat_Sink
HS4
1
R219
4K7
Q205
BC858ALT1
sot23
3
R255
R222
4K7
4
GND_POWER_2
3
+
VS2
R245 0
V_123
V2
R225 1K
BO
C227 0R / Jumper
R226 750
MMSD4148
sod123
Backlight
controller
supply to
Backlight
board
D217
R227
1K
2
R237
10K
2
C230
R231 16K2
Q207
BC858ALT1
sot23
VS2
R238
10K
VS1
NA
D219
VS_123
2_5VREF
1
VS1
CN201
4324-11S
Flyback power to
11
10
Signal processing
9
and Audio board
8
7
6
5
4
3
2
1
0R / Jumper
sod123
R232 6K19
P
2
to92d
TL431ACLPRPG
MMSD4148
sod123
C229
3
NA
470nF
1
VS2
PC101_DRV
R230
VS-Stby
C228 470nF
3
SFH817A
IC201
CN202
4324-03S
1
2
3
1
V1
PC101A
VS1
R236
470
D215
R214 10k
R223
1K
1
10M 2W
R203 33k
C224
470u 16V
Regulation
10u 50V
PFC-OK
D211
MMSD4148
sod123
1
Gnd_Lug
CN404
1
VS1
cyld400l200c
+
C219
3
10uH
2
Y 1nF
C216
SFH817A
N
P
1
T200-78
C225
L202
1
Gnd_Lug
CN403
R221
0.47R 2W
res1000
Q204
BC808-25LT1
VCC4
V1
MBRF20L80CTG
C218
100p 1KV
3K3
D210
to220
8
7
sod123
MMSD4148
CS
C215
R209 100
FB
Q203
STP5NK80ZFP
to220decalD
DRV_Q203
R218
+
470u 16V
P
D209
100n
PC101B
P
100n
PWM_VCC
6
C209
470u 16V
C222
470u 16V
N
4
C211
VCC
R215
MJD200 220
DPAK
R216
220
2
C210
68p
CS
7
+
C221
C214
3
CS
BO
Q202
P
3
FB
470u 16V
N
2
VS2
+
ZD201
MMSZ4692T1
sod123
Heat_Sink
HS3
1
470
330p
FB
C217
47u 25V
C213
8
2
C206
470u 16V
N
CT
10uH
cyld400l200c
+
P
ZCD
L201
1
5
+
R213
sod123
+
N
1
IC200
NCP1379
V2
T200-12
C205
2
MMSD4148
R211
1K
sod123
D206
MMSD4148
BO
3
C208
470u 16V
*
BAV21
do41d
+
C207
470u 16V
*
ZD200
MMSZ4702T1 (15V)
D203
470k
sod123
2
to220
MBRF20L80CTG
6
VCC3
R206
1
D207
2
T200-6
J200
INSTALL
P
R205
1K
*
P
11
T200-3
N
3
P
*
MUR180
do41d
P
SNUBR1
N
R251
33K 2W
1
R252
33K 2W
R233
2K4
N
+
D221
C232
470u 16V
Regulation
GND_REG
R228 100
BAT54T1
sod123
ON
Model Name
Size
Engineer
Subject
ON SEMICONDUCTOR TWN S.E.C.
13 mm 46 Power
A3
Dale Tittensor
Flyback SMPS Pilot
Revision
Date
Reviewer
Sheet
PCB 1
2010-06-18
Jean-Paul Louvel
3 of 3
90
Key parts modification for the 13 mm version
Position
HS1
HS2
HS3
HS4
L002
L003
L004
L005
T100
T200
IC100
Component Type
Bridge Rectifier Heat Sink
PFC Heat Sink
Flyback MOS Heat Sink
Flyback Diodes Heat Sink
PFC Coil
PFC Coil
Common Mode Filter
Common Mode Filter
Standby Transformer
Switch Mode Transformer
44Khz GTO Switch-Reg.
Value
Rating
(heat sink, filters, coils and transformers)
Pkg / Dimensions
Length 120mm Height 12.5 mm
Length 120mm Height 12.5mm
Length 40mm Height 12.5 mm
Length 80mm Height 12.5 mm
200uH
EFD30 TOP Manual
200uH
EFD30 TOP Manual
8.5mH
3.3A
TOP Manual
8.5mH
3.3A
TOP Manual
2.5mH
EF12.6 TOP Manual
680uH
EFD30 TOP Manual
NCP1052P44G
PDIP-8
Reference
TP207ST,120.0,12.5, NA,SP, 02B
TP207ST,120.0,12.5, NA,SP, 01
TP207ST,40.0,12.5, NA,SP, 01
TP207ST,80.0,12.5, NA,SP, 01
750370081
750370081
PH9080NL
PH9080NL
750871014 Rev 04
750875731
NCP1053P44G
Supplier
Columbia-Staver
Columbia-Staver
Columbia-Staver
Columbia-Staver
WURTH ELEKTRONIK
WURTH ELEKTRONIK
PULSE
PULSE
WURTH ELEKTRONIK
WURTH ELEKTRONIK
ON Semiconductor
91
8 mm SLIM Power solution pictures
(310 mm x 290 mm)
Overview
PFC side
Flyback side
92
Zoom PFC side
Zoom Flyback side
93
94
95
13 mm Power solution pictures
(230 mm x 290 mm)
Overview
96
PFC side
Flyback side
97
98
99