Motors VD-VDC EN

VARIODRIVE and
VARIODRIVE Compact motors
VARIODRIVE
VARIODRIVE Compact
Technical Information
VARIODRIVE
VARIODRIVE offers you the extensive power range and dynamics of a modern EC drive with a priceperformance ratio that has so far been deemed inconceivable. The motors and motor electronics of
this product line originated essentially from the basic elements of the renowned ebm-papst DC
fans. Production processes and material procurement profit from the millions of fans produced.
This formed the basis for 5 sizes of 1- and 3-phase EC external rotor motors in an extensive performance range.
With high operating efficiency – in other words – with low energy consumption and high motor
performance, these motors are a convincing solution, offering a wide speed range and excellent
control characteristics. High torque constancy, no vibration and virtually noiseless running are further advantages of these motors.
VARIODRIVE Compact
This is total integration – with a 3-phase electronically commutated DC motor and the control electronics all in a single package: Unrivalled in this performance class. The extremely compact drive
unit with microprocessor-controlled motor manager and FET power stage has an internal closedloop speed control compatible with all standard industrial interfaces. This means: just connect it up
and off you go!
VARIODRIVE Compact is ultraflexible. The motor can be speed controlled and the desired speed
selected via a set value voltage. Via 2 control inputs the direction of rotation can be selected, the
motor can be enabled or a motor brake function can be activated. An open collector frequency output for monitoring the actual speed is also available.
2
Data and facts VARIODRIVE
• 1- and 3-phase external rotor motors
in 5 different sizes.
• EC technology for long service life and
silent running.
• Power range: 3 to 100 Watt.
• Precision ball bearings.
• Spur gears in different gear reduction
stages for a variety of applications.
Data and facts VARIODRIVE Compact
• 3-phase, electronically commutated external
rotor motor.
• Excellent control response over the entire
speed range due to digital 4-Q PI controller.
• High operating efficiency due to FET power
stage and special control process.
• Excellent speed stability, silent running, long
service life.
• Motor manager: Safe operation in all working
point by speed-dependent current limiting
and by stall protection pulsing.
• ACTUAL speed output.
• Motor electronics optimally adapted to motor
characteristic.
• Spur gears and planetary gears in different
gear reduction stages for a variety of applications.
• Winding insulation as per insulation class E.
• Standard protection class IP 00, for VDCS-354.14 and VDC 3-54.32 in IP 40.
• Customer-specific winding layout and motor
part sets available on request (e.g. fixed
speed, direction of rotation).
Contents
The 1- and 3-phase brushless outer rotor motor design has proven its reliability in millions of ebmpapst fan products. Based on this quality and experience VARIODRIVE and VARIODRIVE Compact
motors offer excellent speed stability, silent running and a safe and long service life.
VARIODRIVE-Motor
– Commutation
4
VARIODRIVE 1-phase external rotor motors
– VD-1-27.08
– VD-1-27.15
– VD-1-35.05
– VD-1-43.10
– VD-1-54.14
5
6
7
8
9
VARIODRIVE 3-phase external rotor motors
– VD-3-25.07
– VD-3-35.06
– VD-3-43.10
– VD-3-54.14
10
11
12
13
VARIODRIVE Compact motors
– VDC-3-43.10
– VDC-3-54.14
– VDCS-3-54.14
– VDC-3-54.32
14
16
18
20
VARIODRIVE Compact gear motors
– VDC-3-43.10
– VDC-3-54.14
– VDC-3-54.32
22
26
30
DRIVECONTROL VT-A
33
Accessories
35
Addresses
37
3
VARIODRIVE
Commutation
The following diagram illustrates the sequence of the Hall signals and the corresponding
drive sequence with the relevant colours and / or pin assignment that apply to self-developed
products and / or to purchased electronics. It also illustrates the phase position of these
signals to the induced motor voltage.
Commutation sequences
Clockwise direction of rotation
Commutation sequences
Chronological signal sequence of integrated
Hall sensors (= RLG) at the corresponding
connections.
VARIODRIVE
Position
Assignment
RLG 3
3
RLG 2
4
5
RLG 1
360°
Electrical
Switching sequences of the power output stage
L3
Required relationship between the signal
change from RLG and the relevant change for
the switching status of the power transistors
in relation to the phase lead to the motor.
Phase W
6
7
L2
Phase V
L1
Phase U
8
Induced voltages
Idealized illustration of the sequence of the
induced voltages between the relevant connections.
L3-L1
6-8
L2-L3
7-6
L1-L2
8-7
Total of induced voltages
Supply voltage for Hall sensor
Hall-IC A 3187 LUA
Hall-IC
Supply voltage range:
VCC = 4.5 ... 24 V
Signal output: Open Collector
Max. output voltage: Vo = 24 V
Max. output current: Io = 20 mA
4
+ UB, Hall
1
Gnd
2
Plug
Electrical connection via 8-pole motor plug
(not included in scope of delivery)
AMP-Edge 5 mm: No. 829-213-8 = VD-3-54.14
AMP-Duoplug: Type 2.5 No. 3-82 98 68-8
optional
Lumberg-Duomodul: Type 3 21 08K30 = VD-3-35.06
and VD-3-43.10
Connector position
Notation
1
2
3
4
5
6
7
8
V CC
GND
RLG 3
RLG 2
RLG 1
L3
L2
L1
VARIODRIVE-Motor
VD-1-27.08
–
–
–
–
–
–
–
1-phase, 2-core reluctance motor as external rotor version.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via Hall sensor.
Commutation electronics fully integrated in the motor.
Load-dependent speed setting via connection voltage.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
Typ BCI 42.25
12 V DC
24 V DC VD-1-27.08
Nominal voltage (UBN)
V DC
24 (16 ... 28)
Nominal speed (nN)
min-1
4 500
Nominal torque (MN)
mNm
5.70
Nominal current (IBN)
A
0.25
Nominal output power (PN)
W
Free-running speed (nL)
min
Free-running current (IBL)
A
0.10
Induced voltage (Uimax)
V/1000min-1
3.25
Average starting torque
mNm
14
Max. starting current
A
0.60
Rotor moment of inertia (JR)
kgm2x10-6
11.0
Thermal resistance (Rth)
K/W
40 V DC
60 V DC
2.7
6 800
-1
14
Protection class
IP 00
Ambient temperature range (TU)
°C
0 ... +40
Motor mass (m)
kg
0.12
Order No.
Clockwise rotation
937 2708 500
Order No.
Counterclockwise rotation
937 2708 550
Fradial
Faxial
Faxial
Fradial
4N
10 N
Electrical connection:
Electrical connection via 2 single leads, AWG
24, TR 64, 300 mm long with stripped and
tinned ends.
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
+ = red – = blue
8
0,8
300 min.
S
0°
3x
3
3xM
0
ø35,1
0,2
I
30±0,1
12
-0,005
0,4
ø3 -0,009
4
2
34,1±0,5
0,6
M
ø41+0,3
6
14,5 ±0,5
2 x ø2,5
min -1
x1000
A
S
2
4
6
8
10
mNm
5
VARIODRIVE-Motor
VD-1-27.15
–
–
–
–
–
–
–
1-phase, 2-core reluctance motor as external rotor version.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via Hall sensor.
Commutation electronics fully integrated in the motor.
Load-dependent speed setting via connection voltage.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
VD-1-27.15
Nominal voltage (UBN)
V DC
24 (16 ... 28)
Nominal speed (nN)
min-1
4 200
Nominal torque (MN)
mNm
8.6
Nominal current (IBN)
A
0.32
Nominal output power (PN)
W
Free-running speed (nL)
min
Free-running current (IBL)
A
0.12
Induced voltage (Uimax)
V/1000min-1
3.50
Average starting torque
mNm
24
Max. starting current
A
0.80
Rotor moment of inertia (JR)
kgm2x10-6
15.0
Thermal resistance (Rth)
K/W
3.8
6 400
-1
8
Protection class
IP 00
Ambient temperature range (TU)
°C
0 ... +40
Motor mass (m)
kg
0.15
Order No.
Clockwise rotation
–
Order No.
Counterclockwise rotation
937 2715 550
Faxial
Faxial
Fradial
4N
10 N
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
min -1
x1000
A
L1
8
0,8
6
+ = red – = blue
14,5 ±0,5
40,7 ±0,5
I
0,2
0
2
4
6
8
10
mNm
12
3x
M3
S
3x
S
2
ø35,1
0,4
ø41+0,3
-0,005
ø3 -0,009
4
30 ±0,1
0°
0,6
M
6
Electrical connection:
Electrical connection via 2 single leads, AWG
24, TR 64, 300 mm long with stripped and
tinned ends.
2 x ø2,5
Fradial
300 min.
VARIODRIVE-Motor
VD-1-35.05
–
–
–
–
–
–
–
1-phase, 2-core reluctance motor as external rotor version.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via Hall sensor.
Commutation electronics fully integrated in the motor.
Load-dependent speed setting via connection voltage.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Typ
VD-1-35.05
Nominal voltage (UBN)
V DC
24 (12 ... 28)
Nominal speed (nN)
min-1
5 000
Nominal torque (MN)
mNm
3.4
Nominal current (IBN)
A
0.31
Nominal output power (PN)
W
Free-running speed (nL)
min
Free-running current (IBL)
A
0.20
Induced voltage (Uimax)
V/1000min-1
2.40
Average starting torque
mNm
19
Max. starting current
A
0.20
Rotor moment of inertia (JR)
kgm2x10-6
16.0
Thermal resistance (Rth)
K/W
1.8
6 000
-1
6.60
Protection class
IP 00
Ambient temperature range (TU)
°C
0 ... +40
Motor mass (m)
kg
0.12
Order No.
Clockwise rotation
937 3505 500
Order No.
Counterclockwise rotation
937 3505 550
Fradial
Faxial
Faxial
Fradial
5N
25 N
Electrical connection:
Electrical connection via 2 single leads, AWG
24, TR 64, 300 mm long with stripped and
tinned ends.
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
+ = red – = blue
2,5
4
0,4
3
57
7,2
47
0,005
0,01
0,5
20±0,5
29,3 ±1
Ø4
5
0,05
0,6
M
Ø22
min -1
x1000
A
Ø44
L1
0,3
I
0,2
1
0,1
S
2
S
1
2
3
4
mNm
300 ±10
4,5 +0,3
R
5
0
7
VARIODRIVE-Motor
VD-1-43.10
–
–
–
–
–
–
–
1-phase, 2-core reluctance motor as external rotor version.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via Hall sensor.
Commutation electronics fully integrated in the motor.
Load-dependent speed setting via connection voltage.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
VD-1-43.10
...504
...508
Nominal voltage (UBN)
V DC
24 (12 ... 28)
12
24 (12 ... 25)
Nominal speed (nN)
min-1
4 000
3 800
3 450
Nominal torque (MN)
mNm
18
11
19.5
Nominal current (IBN)
A
0.55
0.7
0.5
Nominal output power (PN)
W
7.5
4.4
7.0
Free-running speed (nL)
min
7 000
5 250
6 300
Free-running current (IBL)
A
0.18
0.3
0.15
Induced voltage (Uimax)
V/1000min-1
3.7
2.19
4.0
Average starting torque
mNm
70
50
50
Max. starting current
A
2.5
3.0
1.5
Rotor moment of inertia (JR)
kgm2x10-6
40
40
40
Thermal resistance (Rth)
K/W
4.5
5,0
5,0
IP 00
IP 00
IP 00
-1
Protection class
°C
0 ... +40
0 ... +40
0 ... +40
Motor mass (m)
kg
0.24
0.24
0.24
Order No.
Clockwise rotation
937 4310 500
937 4310 504
937 4310 508
Order No.
Counterclockwise rotation
937 4310 550
–
–
5N
30 N
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
65
40,8 ±1
7,2
56
Ø52,8
L1
2,5
20 ±0,5
0,005
0,01
Faxial
Faxial
Fradial
Ø4
Fradial
Ø25 – 0,05
Ambient temperature range (TU)
5
1,0
1
0,2
4,
5
0
S
5
10
15
20
25
mNm
Screw-in depth
2,5+0,15
ø4 –0,005
–0,01
0,4
S
2
M3 (4x)
7,2
ø16 –0,05
0,6
I
R
40,8 ±1
10,5 ±0,5
0,8
3
8
Type 504 / 508: VARIODRIVE with round flange
+ = red – = blue
4
4,5 +0,3
25,5 ±0,1
1,2
M
300 ±10
57±0,1
6
Electrical connection:
Electrical connection via 2
single leads, AWG 22, TR
64, 300 mm long with
stripped and tinned ends.
ø52,8
min -1
x1000
A
1,4
405 ±10
90° ±0,5°
VARIODRIVE-Motor
VD-1-54.14
–
–
–
–
–
–
–
1-phase, 2-core reluctance motor as external rotor version.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via Hall sensor.
Commutation electronics fully integrated in the motor.
Load-dependent speed setting via connection voltage.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
VD-1-54.14
Nominal voltage (UBN)
V DC
24 (12 ... 28)
Nominal speed (nN)
min-1
4 000
...550
24 (20 ... 28)
3 300
Nominal torque (MN)
mNm
62
40
Nominal current (IBN)
A
1.75
0.95
Nominal output power (PN)
W
26
14
Free-running speed (nL)
min
8 000
5 400
Free-running current (IBL)
A
0.70
0,55
Induced voltage (Uimax)
V/1000min-1
4.2
5.6
Average starting torque
mNm
100
100
Max. starting current
A
2.7
2.0
Rotor moment of inertia (JR)
kgm2x10-6
200
200
Thermal resistance (Rth)
K/W
3.2
3.5
-1
Protection class
IP 00
IP 00
Ambient temperature range (TU)
°C
0 ... +40
0 ... +40
Motor mass (m)
kg
0.52
0.52
Order No.
Clockwise rotation
937 5414 502
–
Order No.
Counterclockwise rotation
–
937 5414 550
Faxial
Fradial
Fradial
Faxial
10 N
60 N
Electrical connection:
Electrical connection via 2 single leads, AWG
24, TR 64, 300 mm long with stripped and
tinned ends.
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
+ = red – = blue
2,5
20 ±0,5
2,4
1,6
I
2
Ø25 – 0,05
M
4
82
7,2
68
Ø6
6
43,3±1
0,005
0,01
2,8
Ø68,4
min -1
x1000
A
S
0,8
0
4,5 +0,3
7
10
20
30
40
50
60
mNm
300 ±10
R
S
9
VARIODRIVE-Motor
VD-3-25.07
–
–
–
–
–
–
3-phase, 6-pulse external rotor motor.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
VD-3-25.07
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Permanent stall torque (MBNO)
Permissible eff. stall current, motor lead (InOeff)
Permissible permanent input power at stall (PBnO)
Short-term permiss. peak torque (Mmax)
Permiss. peak current, motor lead (Imax)
Induced voltage (Uimax)
Terminal resistance
Terminal inductance
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
5N
5N
V DC
min-1
mNm
A
W
min-1
A
mNm
A
W
mNm
A
V/1000min-1
Ω
mH
kgm2x10-6
K/W
°C
kg
Operating electronics:
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
24
6 000
8.0
0.4
5
8 500
0.095
7.0
0.32
2.0
40
1.8
2.78
14.8
8
4.3
16.7
IP 00
0 ... +40
0.055
937 2507 000
Pin
Connection
position
Adapted operating electronics
DRIVECONTROL VT-A on request.
1
7
2
8
min -1
x1000
A
8
ø48 ±0,2
ø41
0,8
PS1
6
U
7
V
8
W
23,6 ±0,5
2max
ø31,5 –0,25
ø32 –0,3
0,005
0,008
0,2
PS2
5
5 ±0,1
2
+Ub
4
°
I
PS3
3
20
0,4
4
GND
2
3x1
ø3
0,6
ø12 –0,05
1,5 ±0,2
M
6
1
S
20 ±0,5
0
S
10
2
4
6
8
10
mNm
20±0,5
Blind holes for self
threading screws with
nominal diameter of
3,0 mm.
VARIODRIVE-Motor
VD-3-35.06
–
–
–
–
–
–
3-phase, 6-pulse external rotor motor.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Permanent stall torque (MBNO)
Permissible eff. stall current, motor lead (InOeff)
Permissible permanent input power at stall (PBnO)
Short-term permiss. peak torque (Mmax)
Permiss. peak current, motor lead (Imax)
Induced voltage (Uimax)
Terminal resistance
Terminal inductance
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
5N
20 N
V DC
min-1
mNm
A
W
min-1
A
mNm
A
W
mNm
A
V/1000min-1
Ω
mH
kgm2x10-6
K/W
°C
kg
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
VD-3-35.06
...010
24
7 500
20
1.25
16
11 000
0.25
16
1.0
5.0
69
4.0
2.19
3,7
2.5
16
5.2
IP 00
0 ... +40
0.120
937 3506 000
24
3 700
20
0.8
8
7 100
0.16
16
0.6
5.0
69
2,5
3.52
9.4
6.4
16
7.0
IP 00
0 ... +40
0.120
937 3506 010
Operating electronics for speed-controlled operation:
for Order No. 937 3506 000 = DRIVECONTROL VT-A / Order No. 937 1201 001
for Order No. 937 3506 010 = DRIVECONTROL VT-A / Order No. 937 1201 002
2,5
57
29,3±1
2
0,3
0,005
0,01
20±0,5
20±0,5
0,6
S
4
4,5 +0,3
0,9
I
ø22–0,05
ø4
6
5
1,2
R
M
8
47
7,2
1,5
ø44
min -1
x1000
A
0
S
5
10
15
20
mNm
28 –0,15
11
VARIODRIVE-Motor
VD-3-43.10
–
–
–
–
–
–
3-phase, 6-pulse external rotor motor.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Permanent stall torque (MBNO)
Permissible eff. stall current, motor lead (InOeff)
Permissible permanent input power at stall (PBnO)
Short-term permiss. peak torque (Mmax)
Permiss. peak current, motor lead (Imax)
Induced voltage (Uimax)
Terminal resistance
Terminal inductance
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
7N
35 N
V DC
min-1
mNm
A
W
min-1
A
mNm
A
W
mNm
A
V/1000min-1
Ω
mH
kgm2x10-6
K/W
°C
kg
24
7 900
53
2.7
44
10 200
0.27
50
2.7
10
110
6.5
2.03
0.96
1.55
40
4.11
IP 00
0 ... +40
0.24
937 4310 000
24
3 700
54
1.6
21
8 000
0.18
49
1.8
10
110
4.2
3.07
2.3
3.5
40
4.75
IP 00
0 ... +40
0.24
937 4310 010
1,2
2
0,6
–0,005
4,5 +0,3
4
Ø 5 –0,01
1,8
Ø25 –0,05
I
6
5
2,4
4,
M
8
65
56
40,8 ±1
R
2,5
7,2
Ø52,8
min -1
x1000
A
3,0
19±0,5
S
20 ±0,5
0
S
12
...010
Operating electronics for speed-controlled operation:
for Order No. 937 4310 000 = DRIVECONTROL VT-A / Order No. 937 1401 001
for Order No. 937 4310 010 = DRIVECONTROL VT-A / Order No. 937 1401 002
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
VD-3-43.10
10
20
30
40
50
mNm
28 –0,15
VARIODRIVE-Motor
VD-3-54.14
–
–
–
–
–
–
3-phase, 6-pulse external rotor motor.
EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Customer-specific winding layout and / or motor part sets available on request.
Nominal Data
Type
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Permanent stall torque (MBNO)
Permissible eff. stall current, motor lead (InOeff)
Permissible permanent input power at stall (PBnO)
Short-term permiss. peak torque (Mmax)
Permiss. peak current, motor lead (Imax)
Induced voltage (Uimax)
Terminal resistance
Terminal inductance
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
10 N
60 N
V DC
min-1
mNm
A
W
min-1
A
mNm
A
W
mNm
A
V/1000min-1
Ω
mH
kgm2x10-6
K/W
°C
kg
...010
...005
24
5 600
150
5.1
88
7 100
0.41
115
4.4
13
400
15
3.06
0.49
1.00
145
2.5
IP 00
0 ... +40
0.52
937 5414 000
24
3 700
150
3.6
57
5 200
0.26
115
3.1
13
400
10
4.38
0.96
2.00
145
3.0
IP 00
0 ... +40
0.52
937 5414 010
24
6 200
150
5.7
97
7 250
0.43
135
5.4
13
440
20
2.95
0.33
0.72
165
2.4
IP 00
0 ... +40
0.52
937 5414 005
Operating electronics for speed-controlled operation:
for Order No. 937 5414 000 = DRIVECONTROL VT-A / Order No. 937 2501 001
for Order No. 937 5414 010 = DRIVECONTROL VT-A / Order No. 937 2501 002
for Order No. 937 5414 005 = DRIVECONTROL VT-D on request
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
VD-3-54.14
min -1
x1000
A
2,5
7,2
4,8
43,3 ±1
82
68
R
I
0
S
30
60
90
120
150
mNm
12 ±0,5
1,2
4,5+0,3
2
Ø25 –0,05
2,4
S
4
Ø68,4
3,6
M
–0,005
Ø6 –0,01
7
6
20±0,5
42 –0,2
13
VARIODRIVE Compact-Motor
VDC-3-43.10
–
–
–
–
–
–
–
3-phase external rotor motor in EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
High operating efficiency due to FET power stage.
Analogue set value.
Operating mode selection (direction of rotation, braking and motor enable) via 2 control
inputs.
– Protection against overload due to integrated, speed-dependent current limiting.
– Customer-specific version possible based on software and hardware adaption
(e.g. fixed speed, direction of rotation).
Nominal Data
Type
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Max. reverse voltage
Set value input
Desired speed
Recommended speed control range
Function for motor protection at stall
by stall protection pulsing
Overload protection
Average starting torque
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
V DC
min-1
mNm
A
W
min-1
A
V DC
V
min-1
min-1
mNm
kgm2x10-6
K/W
°C
kg
10 N
35 N
VDC-3-43.10
...610
24 (18 ... 28)
6 800
45
2.0
32
10 200
0.4
40
0 ... 10
0 ... 10 000
300 ... nmax
yes
Ton 0.8 / Toff 2.5 s
yes
67
40
3.6
IP 00
0 ... +40
0.24
937 4310 600
24 (18 ... 28)
4 000
45
1.25
18.8
4 080
0.14
40
0 ... 10
0 ... 4 000
300 ... nmax
yes
Ton 0.8 / Toff 2.5 s
yes
67
40
4.1
IP 00
0 ... +40
0.24
937 4310 610
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
A
2,5±0,15
2,5
7,2
4
1,0
2
0,5
19 ±0,5
I
4,5 +0,3
Ø52,8
–0,006
Ø 6 –0,009
1,5
5
6
56
4,
2,0
8
65
R
M
40 ±1
±0,3
Ø25 –0,05
min -1
x1000
L1
S
20 ±0,5
0
S
14
10
20
30
40
50
28 +0,15
mNm
Permissible S1 operating characteristics
Order No. 937 4310 600
Speed n (min-1)
300
1000
Torque M (mNm)
40
40
Input power Ps1 max (W)
7
11
2000
46
19
4000
45
30
Order No. 937 4310 610
Speed n (min-1)
Torque M (mNm)
Input power Ps1 max (W)
2000
45
20
4000
45
30
300
40
10
1000
45
15
5000
45
45
Pin connection
ACTUAL ACTUAL Speed value
ACTUAL
A
B
C
S+
SGND
UB
A
B
C
Input A
Input B
Not connected
S+
SGND
+UB
Set value
Ground set value
Ground
Supply voltage
1. Control inputs
A
B
0
0
1
1
0
1
0
1
low (0)
high (1)
* Brake function:
The braking function serves to
slow down the motor only.
It has no holding brake function
for static duty.
Power stage disabled
Counterclockwise rotation
Clockwise rotation
Brake function*
A/B
0 ... 0.8 V
2.4 ... 30 V
GND
2. Actual speed value output
Version:
Open Collector
Uext. max = 30 V
UCESAT = 0.5 V
ICMAX = 5mA
Output signal
UExt.
ACTUAL
Motor logic
External control
100 Hz = 1000 min -1
t
GND
3. Set value
Speed setting for speed control via set
value voltage (interface 0 ... 10 V DC).
S+
Speed
nmax
S0
S
nmin
0
S min
Set value voltage
max
GND
For detailed information, please refer to the corresponding specification data sheets.
The instructions and safety notes in the operating manual must be kept at all times.
15
VARIODRIVE Compact-Motor
VDC-3-54.14
–
–
–
–
–
–
–
3-phase external rotor motor in EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
High operating efficiency due to FET power stage.
Analogue set value.
Operating mode selection (direction of rotation, braking and motor enable) via 2 control
inputs.
– Protection against overload due to integrated, speed-dependent current limiting.
– Customer-specific version possible based on software and hardware adaption
(e.g. fixed speed, direction of rotation).
Nominal Data
Type
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Max. reverse voltage
Set value input
Desired speed
Recommended speed control range
Function for motor protection at stall
by stall protection pulsing
Overload protection
Average starting torque
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
V DC
min-1
mNm
A
W
min-1
A
V DC
V
min-1
min-1
mNm
kgm2x10-6
K/W
°C
kg
20 N
60 N
VDC-3-54.14
...620
24 (18 ... 28)
6 000
100
3.6
62.8
8 000
0.51
40
0 ... 10
0 ... 10 000
300 ... nmax
yes
Ton 0.8 / Toff 2.5 s
yes
120
145
2.5
IP 00
0 ... +40
0.52
937 5414 622
24 (18 ... 28)
3 500
100
2.8
47.6
4 000
0.21
40
0 ... 10
0 ... 4 000
300 ... nmax
yes
Ton 0.8 / Toff 2.5 s
yes
120
145
3.0
IP 00
0 ... +40
0.52
937 5414 620
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
2,5
min -1
x1000
A
42±1
82±0,5
7,2±0,3
68
R
8
7
4,0
2
S
1,0
0
S
16
20
40
60
80
100
mNm
12 ±0,5
2,0
I
4,5 +0,3
4
Ø25 –0,05
3,0
Ø68,3±0,1
6
–0,005
Ø6 –0,01
M
20±0,5
42 –0,2
Permissible S1 operating characteristics
Order No. 937 5414 622
Speed n (min-1)
Torque M (mNm)
Input power Ps1 max (W)
300
90
14
1000
90
22
2000
90
33
4000
100
63
Order No. 937 5414 620
Speed n (min-1)
Torque M (mNm)
Input power Ps1 max (W)
300
110
14
1000
110
23
2000
120
40
4000
130
70
6000
100
88
Pin connection
X2:1
ACTUAL ACTUAL Speed value
ACTUAL
A
B
C
A
B
C
S+
Input A
Input B
Not connected
S+
SGND
+UB
Set value
Ground set value
Ground
Supply voltage
SGND
UB
1. Control inputs
A
B
0
0
1
1
0
1
0
1
low (0)
high (1)
* Brake function:
The braking function serves to
slow down the motor only.
It has no holding brake function
for static duty.
Power stage disabled
Counterclockwise rotation
Clockwise rotation
Brake function*
A/B
0 ... 0.8 V
2.4 ... 30 V
GND
2. Actual speed value output
Version:
Open Collector
Uext. max = 30 V
UCESAT = 0.5 V
ICMAX = 5mA
Output signal
UExt.
ACTUAL
Motor logic
External control
100 Hz = 1000 min -1
t
GND
3. Set value
Speed setting for speed control via set
value voltage (interface 0 ... 10 V DC).
S+
Speed
nmax
S0
S
nmin
0
S min
Set value voltage
max
GND
For detailed information, please refer to the corresponding specification data sheets.
The instructions and safety notes in the operating manual must be kept at all times.
17
VARIODRIVE Compact Small-Motor
VDCS-3-54.14
–
–
–
–
–
–
3-phase external rotor motor in EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics for open loop speed-controlled operation.
Analogue set value for open loop speed control.
Direction of rotation setting via control input.
Protection against overload due to integrated, speed-dependent current limiting.
Nominal Data
Type
VDCS-3-54.14
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Max. reverse voltage
Set value input
Function for motor protection at stall
Overload protection
Average starting torque
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
V DC
min-1
mNm
A
W
min-1
A
V DC
V
24 (18 ... 28)
6 000
90
3.3
56.5
7 800
0.51
0 ... 10
optional
yes
80
145
IP 40
0 ... +40
0.72
937 5414 800
mNm
kgm2x10-6
K/W
°C
kg
20 N
60 N
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
L1
min -1
x1000
3,0
4
3,7 H10
4,65 H10
6
ø86±0,2
M
4x90°
4,0
ø25 ±00,3
ø8g5
56±1
8
2,0
I
2
0
20
40
60
80
100
mNm
25±0,3
300 ±10
S
6±0,2
2±0,1
60 ±5
4 ±0,5
1,0
S
18
ø49
ø40
ø36
A
Permissible S1 operating characteristics
Order No. 937 5414 800
Speed n (min-1)
Torque M (mNm)
Input power Ps1 max (W)
300
80
12
1000
80
19
2000
80
29
4000
90
56
5000
90
80
Pin connection
Yellow
White
Green
Black
Red
Ist
A
S+
GND
+Ub
ACTUAL Speed value
Input A
Set value input
Ground
Supply voltage
1. Control inputs
A
*Change in direction of rotation
only allowed at standstill!
0
1
Counterclockwise rotation*
Clockwise rotation*
low (0)
high (1)
0 ... 0.8 V
2.4 ... 30 V
A/B
GND
2. Actual speed value output
Version:
Open Collector
Uext. max = 30 V
UCESAT = 0.5 V
ICMAX = 5mA
Output signal
UExt.
ACTUAL
Motor logic
External control
100 Hz = 1000 min -1
t
GND
3. Set value input
Speed setting for open loop speed
control via control voltage
(0 ... 10 V DC).
interface:
< 2 V = 0% PWM
8 V = 100% PWM
Free-running speed
nmax
S+
GND
0
S
nmin
0
Weitere
Detailinformationen
sind den jeweiligen
Spezifikationsdatenblätter zu entnehmen.
2
Set value voltage
8 10
S
Grundsätzlich sind die Anweisungen und Sicherheitshinweise aus dem Betriebshandbuch zu beachten.
GND
For detailed information, please refer to the corresponding specification data sheets.
The instructions and safety notes in the operating manual must be kept at all times.
19
VARIODRIVE Compact-Motor
VDC-3-54.32
–
–
–
–
–
–
–
3-phase external rotor motor in EC technology.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
High operating efficiency due to FET power stage.
Analogue set value.
Operating mode selection (direction of rotation, braking and motor enable) via 2 control
inputs.
– Protection against overload due to integrated, speed-dependent current limiting.
– Customer-specific version possible based on software and hardware adaption
(e.g. fixed speed, direction of rotation).
Nominal Data
Type
VDC-3-54.32
Nominal voltage (UBN)
Nominal speed (nN)
Nominal torque (MN)
Nominal current (IBN)
Nominal output power (PN)
Free-running speed (nL)
Free-running current (IBL)
Max. reverse voltage
Set value input
Desired speed
Recommended speed control range
Function for motor protection at stall
by stall protection pulsing
Overload protection
Average starting torque
Rotor moment of inertia (JR)
Thermal resistance (Rth)
Protection class
Ambient temperature range (TU)
Motor mass (m)
Order No.
Fradial
Faxial
Faxial
Fradial
V DC
min-1
mNm
A
W
min-1
A
V DC
V
min-1
min-1
24 (18 ... 28)
3 300
240
4.3
83
4 100
0.5
40
0 ... 10
0 ... 4 000
300 ... nmax
yes
Ton 0.8 / Toff 2.5 s
yes
280
500
2.15
IP 40
0 ... +40
1.1
937 5432 610
mNm
kgm2x10-6
K/W
°C
kg
25 N
60 N
L1 10 mm
Permissible shaft load at nominal speed and
life expectancy L10 at 20 000 h.
3
3,0
4x90°
M
ø49
ø40
ø36
82±1
4,0
ø86 ±0,2
4
ø25 ±00,3
ø8g5
min -1
x1000
A
3,7 H10
4,65 H10
L1
1,0
S
6±0,2
2±0,1
0
S
20
50
100
150
200
250
mNm
25±0,3
4±0,5
1
300 ±10
2,0
60±5
I
2
Permissible S1 operating characteristics
Order No. 937 5432 610
Speed n (min-1)
Torque M (mNm)
Input power Ps1 max (W)
300
225
31
1000
225
50
2000
225
70
3300
240
115
Pin connection
Yellow
White
Grey
–
ACTUAL ACTUAL Speed value
A
B
C
Green
–
Black
Red
Input A
Input B
Not connected
S+
SGND
+Ub
Set value
Ground set value
Ground
Supply voltage
1. Control inputs
A
B
0
0
1
1
0
1
0
1
low (0)
high (1)
* Brake function:
The braking function serves to
slow down the motor only.
It has no holding brake function
for static duty.
Power stage disabled
Counterclockwise rotation
Clockwise rotation
Brake function*
A/B
0 ... 0.8 V
2.4 ... 30 V
GND
2. Actual speed value output
Output signal
Version:
Open Collector
Uext. max = 30 V
UCESAT = 0.5 V
ICMAX = 5mA
UExt.
ACTUAL
Motor logic
External control
100 Hz = 1000 min -1
t
GND
3. Set value
Speed setting for speed control via set
value voltage (interface 0 ... 10 V DC).
S+
Speed
nmax
S0
S
nmin
0
S min
Set value voltage
max
GND
For detailed information, please refer to the corresponding specification data sheets.
The instructions and safety notes in the operating manual must be kept at all times.
21
VARIODRIVE Compact
Gear motor VDC-3-43.10-C
Speed range
i
Nm
min-1
VDC-3-43.10-C 16
16.0 : 1
0.6
19 ... 250
947 4310 600
VDC-3-43.10-C 22
22.9 : 1
0.8
13 ... 175
947 4310 601
VDC-3-43.10-C 32
32.0 : 1
1.2
9 ... 125
947 4310 602
VDC-3-43.10-C 45
45.4 : 1
1.5
7 ... 88
947 4310 603
VDC-3-43.10-C 58
57.8 : 1
1.9
5 ... 69
947 4310 604
VDC-3-43.10-C 79
79.1 : 1
2.6
4 ... 51
947 4310 605
VDC-3-43.10-C 122
121.6 : 1
4.0
2 ... 33
947 4310 606
Type VDC
Fradial
Faxial
Faxial
Fradial
40 N
120 N
Gear type C
Multi-stage spur gear in zinc diecast body.
Grease lubrication for maintenance-free continuous
operation.
Shaft output with combined sleeve / needle bearing.
Reversible direction of rotation.
L1 17 mm
Permissible shaft load at nominal speed.
L1
7,2±0,3
1,2 ±0,1
3
25±0,5 40,5 ±0,3
81,8 ±1
22
5,1±0,1
0,5
50,6 ±0,2
21,5±0,2
ø18
12
20
ø52,8 ±0,1
ø19 0,4
ø8 h7
7 0,1
0,5
4xM4
65 ±0,5
61
25,3±0,1
5,1±0,1
69,5
75,5 ±1
Nominal Data
Order No.
Nominal torque
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass 0.55 kg.
Gear ratio
–
–
–
–
–
–
–
28 0,15
50,6 ±0,2
Gear motor VD-3-43.10-C
Motor variation with external operating electronics
i
Nm
min-1
Order No.
Speed range
Type VD
Nominal torque
Nominal Data
3-phase, 6-pulse external rotor motor for gear applications.
EC technology.
Dynamically fine-balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Gear ratio
–
–
–
–
–
VD-3-43.10-C 16
16 : 1
0.8
22 ... 215
947 4310 000
VD-3-43.10-C 22
22.9 : 1
1.1
15 ... 150
947 4310 001
VD-3-43.10-C 32
32 : 1
1.0
11 ... 110
947 4310 002
VD-3-43.10-C 45
45.4 : 1
2.0
8 ... 77
947 4310 003
VD-3-43.10-C 58
57.8 : 1
2.5
6 ... 60
947 4310 004
VD-3-43.10-C 79
79.1 : 1
3.4
5 ... 44
947 4310 005
VD-3-43.10-C 122
121.6 : 1
5.3
3 ... 28
947 4310 006
Operating electronics:
DRIVECONTROL VT-A / Order No. 937 1401 002
Type VD-3-43.10 with AMP-plug (see basic motor page 12). Dimensional drawing for gear motor see page 22.
23
VARIODRIVE Compact
Gear motor VDC-3-43.10-D
Speed range
i
Nm
min-1
VDC-3-43.10-D 11
11.3 : 1
0.4
27 ... 354
947 4310 610
VDC-3-43.10-D 13
13.2 : 1
0.5
23 ... 303
947 4310 611
VDC-3-43.10-D 16
15.9 : 1
0.6
19 ... 252
947 4310 612
VDC-3-43.10-D 26
26.4 : 1
1.0
11 ... 152
947 4310 613
VDC-3-43.10-D 38
38.6 : 1
1.4
8 ... 104
947 4310 614
Nominal Data
Type VDC
Fradial
Faxial
Faxial
Fradial
50 N
150 N
Order No.
Nominal torque
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass 0.62 kg.
Gear ratio
–
–
–
–
–
–
–
Gear type D
Multi-stage spur gear in zinc diecast body.
Grease lubrication for maintenance-free continuous
operation.
Shaft output with combined sleeve / needle bearing.
Reversible direction of rotation.
L1 17 mm
Permissible shaft load at nominal speed.
L1
7,2 ±0,1
24
1±0,2
38 ±0,3
79,2 ±1,4
21,5
50,6 ±0,2
70 ±0,4
5
ø52,8
25±0,1
ø10 h6
9 –0,1
25
±0,5
13,5 ±0,2
ø18 ±0,5
20–0,5
4xM4
±0,1
1,2 ±0,1
25,3
50,6 ±0,2
75
Gear motor VD-3-43.10-D
Motor variation with external operating electronics
Speed range
i
Nm
min-1
VD-3-43.10-D 11
11.3 : 1
0.5
31 ... 310
947 4310 010
VD-3-43.10-D 13
13.2 : 1
0.6
27 ... 265
947 4310 011
VD-3-43.10-D 16
15.9 : 1
0.8
22 ... 220
947 4310 012
VD-3-43.10-D 26
26.4 : 1
1.3
13 ... 130
947 4310 013
VD-3-43.10-D 38
38.6 : 1
1.9
9 ... 90
947 4310 014
Nominal Data
Type VD
Order No.
Nominal torque
3-phase, 6-pulse external rotor motor for gear applications.
EC technology.
Dynamically fine-balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Gear ratio
–
–
–
–
–
Operating electronics:
DRIVECONTROL VT-A / Order No. 937 1401 002
Type VD-3-43.10 with AMP-plug (see basic motor page 12). Dimensional drawing for gear motor see page
25
VARIODRIVE Compact
Gear motor VDC-3-54.14-C
Speed range
i
Nm
min-1
VDC-3-54.14-C 16
16.0 : 1
1.7
19 ... 250
947 5414 600
VDC-3-54.14-C 22
22.9 : 1
2.4
13 ... 175
947 5414 601
VDC-3-54.14-C 32
32.0 : 1
3.4
9 ... 125
947 5414 602
VDC-3-54.14-C 45
45.4 : 1
4.3
7 ... 88
947 5414 603
VDC-3-54.14-C 58
57.8 : 1
5.5
5 ... 69
947 5414 604
VDC-3-54.14-C 79
79.1 : 1
7.0*
4 ... 51
947 5414 605
VDC-3-54.14-C 122
121.6 : 1
7.0*
2 ... 33
947 5414 606
Nominal Data
Type VDC
Order No.
Nominal torque
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass 0.83 kg.
Gear ratio
–
–
–
–
–
–
–
*Monitor torque limitation at max. 7.0 Nm on output side.
Fradial
Faxial
Faxial
Fradial
40 N
120 N
Gear type C
Multi-stage spur gear in zinc diecast body.
Grease lubrication for maintenance-free continuous
operation.
Shaft output with combined sleeve / needle bearing.
Reversible direction of rotation.
L1 17 mm
Permissible shaft load at nominal speed.
L1
42 ±1
7,2±0,3
1,2±0,1
82 ±0,5
61
25
40,5±0,3
69,5
82 ±0,5
50,6 ±0,2
25,3 ±0,1
42 –0,2
50,6 ±0,2
26
12 ±0,5
3
±0,5
5,1±0,1 21,5±0,2
20+0,5
ø68,4 ±0,1
ø18 +0,5
7–0,1
ø19+0,4
ø8 h7
4xM4
Gear motor VD-3-54.14-C
Motor variation with external operating electronics
Speed range
i
Nm
min-1
VD-3-54.14-C 16
16.0 : 1
1.8
22 ... 215
947 5414 000
VD-3-54.14-C 22
22.9 : 1
2.6
15 ... 150
947 5414 001
VD-3-54.14-C 32
32.0 : 1
3.6
11 ... 110
947 5414 002
VD-3-54.14-C 45
45.4 : 1
4.6
8 ... 77
947 5414 003
VD-3-54.14-C 58
57.8 : 1
5.9
6 ... 60
947 5414 004
VD-3-54.14-C 79
79.1 : 1
7.0**
5 ... 44
947 5414 005
VD-3-54.14-C 122
121.6 : 1
7.0**
3 ... 28
947 5414 006
Nominal Data
Type VD
Order No.
Nominal torque
3-phase, 6-pulse external rotor motor for gear applications.
EC technology.
Dynamically fine-balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Gear ratio
–
–
–
–
–
**Monitor torque limitation at max. 7.0 Nm output based on current limiting on operating electronics.
DRIVECONTROL VT-A, series 2400.
Operating electronics:
DRIVECONTROL VT-A / Order No. 937 2501 002
DRIVECONTROL VT-A / Order No. 937 2401 002
Dimensions on page 26 dimensional drawing.
27
VARIODRIVE Compact
Gear motor VDC-3-54.14-D
Speed range
i
Nm
min-1
VDC-3-54.14-D 11
11.3 : 1
1.2
27 ... 354
947 5414 610
VDC-3-54.14-D 16
15.9 : 1
1.7
19 ... 252
947 5414 611
VDC-3-54.14-D 26
26.4 : 1
2.8
11 ... 152
VDC-3-54.14-D 39
38.6 : 1
4.1
Type VDC
Fradial
Faxial
Faxial
Fradial
50 N
150 N
8 ... 104
947 5414 612
947 5414 613
Gear type D
Multi-stage spur gear in zinc diecast body.
Grease lubrication for maintenance-free continuous
operation.
Shaft output with combined sleeve / needle bearing.
Reversible direction of rotation.
L1 17 mm
Permissible shaft load at nominal speed.
L1
1,2±0,1
13,5±0,2
82 ±0,5
50,6 ±0,2
25±0,5
28
1±0,2
38 ±0,3
42 ±0,2
50,6 ±0,2
75,4
12±0,5
ø10 h6
9–0,1
25±0,1
20 –0,5
ø68,4±0,1
4xM4
ø18 ±0,5
42±1
7,2 ±0,1
70 ±0,4
82 ±0,5
Nominal Data
Order No.
Nominal torque
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass 0.90 kg.
Gear ratio
–
–
–
–
–
–
–
Gear motor VD-3-54.14-D
Motor variation with external operating electronics
Speed range
i
Nm
min-1
VD-3-54.14-D 11
11.3 : 1
1.3
31 ... 310
947 5414 010
VD-3-54.14-D 16
15.9 : 1
1.8
22 ... 220
947 5414 011
VD-3-54.14-D 26
26.4 : 1
3.0
13 ... 130
947 5414 012
VD-3-54.14-D 39
38.6 : 1
4.4
9 ... 90
947 5414 013
Nominal Data
Type VD
Order No.
Nominal torque
3-phase, 6-pulse external rotor motor for gear applications.
EC technology.
Dynamically fine-balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Determination of rotor position via 3 Hall sensors.
Motor supply and control via external operating electronics.
Gear ratio
–
–
–
–
–
Operating electronics:
DRIVECONTROL VT-A / Order No. 937 2501 002
Dimensions on page 28 dimensional drawing.
29
VARIODRIVE Compact
Gear motor VDC-3-54.32-D
Speed range
i
Nm
min-1
Type
Order No.
Nominal torque
Nominal Data
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass 1.39 kg.
Gear ratio
–
–
–
–
–
–
–
VDC-3-54.32-D 9
9.2 : 1
2.0
38 ... 330
947 5432 610
VDC-3-54.32-D 18
18.4 : 1
3.5
19 ... 163
947 5432 611
Fradial
Faxial
Faxial
Fradial
50 N
150 N
Gear type D
Multi-stage spur gear in zinc diecast body.
Grease lubrication for maintenance-free continuous
operation.
Shaft output with combined sleeve / needle bearing.
Reversible direction of rotation.
L1 17 mm
Permissible shaft load at nominal speed.
L1
Yellow
White
Grey
–
Green
–
Black
Red
ACTUAL ACTUAL Speed value
A
B
C
S+
SGND
+Ub
Input A
Input B
Not connected
Set value
Ground set value
Ground
Supply voltage
75
50,6
4xM4
6±0,2
30
4±0,5
1±0,2
38±0,3
300±10
60 ±5
0,5
70
25 ± 0,1
10 h6
9 –0,1
25
50,6
0,5
ø86
20
13,5±0,2
82±1
VARIODRIVE Compact
Gear motor VDC-3-54.32-E
Speed range
i
Nm
min-1
Type
Order No.
Nominal torque
Nominal Data
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass 1.48 kg.
Gear ratio
–
–
–
–
–
–
–
VDC-3-54.32-E 31
31.1 : 1
5.9
11 ... 97
947 5432 620
VDC-3-54.32-E 70
70.4 : 1
11.8
5 ... 43
947 5432 621
Faxial
Fradial
Fradial
Faxial
50 N
150 N
Gear type E
Multi-stage spur gear in zinc diecast body.
Grease lubrication for maintenance-free continuous
operation.
Shaft output with combined sleeve / needle bearing.
Reversible direction of rotation.
L1 17 mm
Permissible shaft load at nominal speed.
L1
ACTUAL ACTUAL Speed value
Input A
Input B
Not connected
Set value
Ground set value
Ground
Supply voltage
15±0,1
4xM5
4±0,5
6±0,2
41,5 ±0,3
60 ±5
1
300±10
20+0,5
25±0,5
83,5
80
ø86
82±1
33,25 ±0,1
83,5
80
66,5 ±0,2
33,25±0,1
66,5±0,2
A
B
C
S+
SGND
+Ub
ø17,5 –0,4
ø10 h7
9 –0,1
Yellow
White
Grey
–
Green
–
Black
Rot
31
VARIODRIVE Compact
Gear motor VDC-3-54.32-PX
Type
i
Nm
min-1
Order No.
Speed range
Nominal Data
3-phase external rotor motor in EC technology for gear applications.
Dynamically balanced rotor with 4-pole, plastic-bonded ferrite magnet.
Integrated operating electronics with powerful microcontroller.
Excellent control response due to digital 4-Q PI controller.
Analogue set value.
Available in various reduction ratios.
Motor mass one stage = 1.5 kg, two stages = 1.7 kg.
Nominal torque
Gear ratio
Gear stages
–
–
–
–
–
–
–
VDC-3-54.32-PX 5
5:1
1
1.1
60 ... 660
on request
VDC-3-54.32-PX 30
30 : 1
2
5.8
10 ... 110
on request
Fradial
Faxial
500 N
350 N
Gear type PX 52
1 to 2-stage planetary gearbox in zinc diecast housing. Grease lubrication for maintenance free operation. Output shaft with combinated needle- / ball
bearings.
Permissible shaft load at nominal speed and
life expectancy L10 von 5 000 h.
L1
Yellow
White
Grey
–
Green
–
Black
Red
Faxial
Fradial
Optimized helical gearing for long service life and
silent running in the first level.
ACTUAL ACTUAL Speed value
A
B
C
S+
SGND
+Ub
Input A
Input B
Not connected
Set value
Ground set value
Ground
Supply voltage
25±0,5
L2
82±1
300 ±10 of motor
60 ±5
12,5
3
16
FR
ø86
ø32 h8
ø52
ø12 h7
3
4±0,5 tin-plated
Keyway
DIN6885 - A4x4x16
32
4x M5
(8 deep)
40
DRIVECONTROL
VT-A series
Operating electronics for driving 3-phase motors of the VARIODRIVE series.
Simple OEM electronics for use in series applications. The DRIVECONTROL VT-A is available in
4 different performance levels for speed-controlled or voltage-controlled operation. Only one
supply voltage is required for motor and electronics.
Nominal Data
Data
Unit
Voltage controlled
Speed controlled
Nominal voltage
Nominal voltage Range
Max. output voltage
Output current, peak
Set value input
Speed control range
Speed control
ACTUAL speed value
Operating temperature range
Temperature monitoring
Mass
Protection class
V
V
V
A
V DC
min-1
Type
24
10 ... 30
UB - 2 V
2-5
0 ... 10
–
–
–
0 ... 40 °C
no
0.2
IP 00
24
14 ... 28
UB - 2 V
2-5
0 ... 10
300 ... 4 000 / 300 ... 10 000
P
yes
0 ... 40 °C
no
0.2
IP 00
°C
MOLEX-Plug
13±0,1
84 ±0,1
112±0,3
AMP-Plug
92 ±0,2
80 ±0,1
3 +0,2
6,5 +0,2
kg
5,5 +0,2
3
20±0,2
33
Functions and performance features
– 1 quadrant controller. Positive set value alterations are adjusted by acceleration. Negative set value alterations cause
short-circuit braking via the motor winding (increase in intermediate circuit voltage possible!).
– Speed setting via set value input (interface 0...10 V DC).
– Setting of operating modes via 2 control inputs.
– Speed-controlled version with evaluation of Hall signals for ACTUAL speed value monitoring via MF-pin.
– With voltage-controlled (= uncontrolled) version, no braking function and ACTUAL speed value monitoring.
– Fixed limits for current and voltage.
– Voltage supply with input filter, filtering and generation of auxiliary voltage.
– Equipped with PCB plug or Molex plug depending on type of motor.
1. Control inputs
Pin connection
Speed controlled Version
Molex
AMP
A
1
3
2
1
6
5
4
4
S1
3
Motor connection 2
1
8
7
6
5
S2
Control signals
6
1
8
B
A
A/B
0
0
1
1
0
1
0
1
Power stage disabled
0
Counterclockwise rotation 1
Clockwise rotation
Brake function*
Counterclockwise rotation
Clockwise rotation
Input B is not connected
GND
low (0)
high (1)
0 ... 0.8 V
2.4 ... 30 V
* Brake function:
The braking function serves to slow down the motor only.
It has no holding brake function for the static duty.
Plug S2
Pin
Type MOLEX Type AMP
2. Actual speed value output (MF-Pin)
1
2
3
4
5
6
GND
A
ncommand
+UB
B
MF-Pin
Only with speed-controlled version, open collector that transmits a short pulse at every flange edge of the
motor Hall signals!
The illustrated signal sequence for standard assembly is the speed value output.
MF-Pin
B
A
ncommand
Gnd
+UB
Voltage range U CE :
Max. current I c :
Pull-up resistor:
Puls length:
U CESat :
MF-Pin
GND
Plug S1
Pin
Type MOLEX Type AMP
1
2
3
4
5
6
7
8
L3
+UHall
RLG 2
RLG 1
L2
L1
GndHall
RLG 3
150us
+UHall
GndHall
RLG 3
RLG 2
RLG 1
L3
L2
L1
t
3. Set value
The speed selection is normally made externally with a voltage in the range of 0...10 V DC. A voltage of 10
V is equivalent to the maximum speed determined internally.
With the voltage controlled version of the VT-A, the set value is internally fixed at the maximum value.
For reducing the set value an external potentiometer can be connected or an external set value voltage can
be applied.
Voltage controlled version
Speed controlled version
The interpretation of the set value and
the corresponding level are described
in the relevant data sheet.
S+
12 V
10k
S+
2k2
Int. Command
12 V
GND
< 30 V
10 mA
> 2000 Ohm by 24 V
150 μs
< 0.8 V
22nF
GND
SGND
Typical wiring of the reference input with the
voltage controlled version. Special features are
described in the relevant data sheets.
For detailed information, please refer to the corresponding specification data sheets.
The instructions and safety notes in the operating manual must be kept at all times.
34
Accessories
Electrical connection
Electronic connection
D
Motor connection cable
A
Type 194 0010 000
Motor connection cable for
VARIODRIVE motors
VD-3-35.06 / VD-3-43.10 and
DRIVECONTROL VT-A with
Molex-plugs.
Plug A
AMP Duoplug 2.5 - 8-pole
grey
No. : 3-829 868-8 (when encoding)
Alternative:
Lumerg 35 21 08K30 (when encoding)
A
A
8 single leads blue - AWG 22
8
8
1
1
500 ±20
Type 194 0012 000
Motor connection cable for
VARIODRIVE motors
VD-3-54.14 and
DRIVECONTROL VT-A with
Molex-plugs.
B
Plug B
Molex 39-01-2085 Mini-Fit, Jr.
Plug C
AMP-Edge 5 mm - 8-pole
No. 829 213-8 (when encoding)
5
6
7
8
8
1
2
3
4
1
8 single leads blue
- AWG 20 -
500 ±20
C
Type 194 0011 000
Electronic connection cable for
DRIVECONTROL VT-A with
AMP-plugs (motors
VD-3-35.06 / VD-3-43.10).
D
Plug D (when encoding)
AMP Duoplug 2.5 - 6-pole grey
No. 3-829 868-6
or Lumberg 35 21 06K30
6 singled leads coloured - AWG 22
6
1
Red
Black
Green
White
Grey
Yellow
500 ±20
35
Type 194 0013 000
Electronic connection cable for
DRIVECONTROL VT-A with
Molex-plugs (motors
VD-3-54.14).
Plug E
Molex 39-01-2065 Mini-fit, Jr.
E
6 singled leads coloured - AWG 20
1 Black
2 White
3 Green
4 Red
5 Grey
6 Yellow
4 1
5 2
6 3
500 ±20
Type 194 0009 000
Motor connection cable for
VARIODRIVE Compact
motors VDC-3-43.10.
Plug F
Lumberg Duomodul connector 2.5 mm
10-pole,
Lumberg Order No.
35 15 10 K05 S01
500 ±20
3 ±5
1
2
3
4
5
6
7
8
9
Yellow
White
Grey
Violet
Green
Brown
Black
Red
10
F
Type 194 0014 000
Motor connection cable for
VARIODRIVE Compact
motors VDC-3-54.14.
Plug G
MT-Edge 5 mm - 8 pole natural
for 0.5 mm contact
with 2 i.p.c.d.
Order No. AMP 829 213-8
500 ±20
G
8 stranded hook-up wires AWG 20 (0,5 mm)
Lead: 7-core
3 ±5
Stripped
drilled and
tinned ends
1
8
Rotor protective cap
B
C
A
Rotor protective cap made of black
polypropylene (PP). The cap is fitted
directly onto the motor flange and
sealed with a rubber seal.
Dimension A
B
C
36
The protective cap cannot be mounted with motor VDC-3-43.10!
When using the protective cap, the motor performance must be
reduced due to the decreased heat dissipation from the motor.
VARIODRIVE VD ... 35.OX
194 3506 000
VARIODRIVE VD ... 43.10
194 4310 000
VARIODRIVE VD ... 54.14
194 5414 000
57
27.4
49.5
65
38.8
57.4
82
42
74.4
Motors Distributors
spec. Motors Distributors
Distributors of ebm-papst
Fans Distributors
Ventilator Distributors
Germany
ebm-papst
St. Georgen GmbH & Co. KG
ebm-papst
Mulfingen GmbH & Co. KG
ebm-papst
Landshut GmbH
Hermann-Papst-Straße 1
D-78112 St. Georgen
Phone +49 (0) 77 24 / 81 - 0
Fax +49 (0) 77 24 / 81 - 13 09
[email protected]
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 79 38 / 81 - 0
Fax +49 (0) 79 38 / 81 - 110
[email protected]
Hofmark-Aich-Straße 25
D-84030 Landshut
Phone +49 (0) 8 71 / 707 - 0
Fax +49 (0) 8 71 / 707 - 465
[email protected]
www.ebmpapst.com
www.ebmpapst.com
www.ebmpapst.com
Agencies
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
16341 Panketal
Phone +49 (0) 30 / 94 41 49 62
Fax +49 (0) 30 / 94 41 49 63
[email protected]
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
59519 Möhnesee-Völlinghausen
Phone +49 (0) 29 25 / 80 04 07
Fax +49 (0) 29 25 / 80 04 08
[email protected]
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr. Hermann-Krause Straße 23
63452 Hanau
Phone +49 (0) 61 81 / 18 98 12
Fax +49 (0) 61 81 / 18 98 13
[email protected]
Halle
Dipl.-Ing. (TU) Michael Hanning
Lerchenweg 4
06120 Lieskau
Phone +49 (0) 3 45 / 5 51 24 56
Fax +49 (0) 3 45 / 5 51 24 57
[email protected]
Hamburg
Ingenieurbüro Breuell GmbH
Elektro.-Ing. Dirk Kahl
Grützmühlenweg 40
22339 Hamburg
Phone +49 (0) 40 / 53 80 92 10
Fax +49 (0) 40 / 53 80 92 84
[email protected]
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
35075 Gladenbach
Phone +49 (0) 64 62 / 40 71 10
Fax +49 (0) 64 62 / 40 71 11
[email protected]
Koblenz
Winfried Schaefer
Hinter der Kirch 10
56767 Uersfeld
Phone +49 (0) 26 57 / 16 96
Fax +49 (0) 26 57 / 16 76
[email protected]
München
Dipl.-Wirt-Ing. (FH) Jens Peter
Steinbergweg 6
82285 Hattenhofen
Phone +49 (0) 81 45 / 80 92 25
Fax +49 (0) 81 45 / 80 92 26
[email protected]
Nürnberg
Friedrich Klein
Adlerstraße 49/1
73540 Heubach
Phone +49 (0) 71 73 / 49 83
Fax +49 (0) 71 73 / 80 53
[email protected]
Offenburg
Dipl.-Ing (FH) Ralf Braun
Hubeneck 21
77704 Oberkirch
Phone +49 (0) 78 02 / 98 22 52
Fax +49 (0) 78 02 / 98 22 53
[email protected]
Paderborn
Wolf-Jürgen Weber
Niehausweg 13
33739 Bielefeld
Phone +49 (0) 5206 / 91 73 231
Fax +49 (0) 5206 / 91 73 235
[email protected]
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Mühlhaldenweg 13
73207 Plochingen
Phone +49 (0) 71 53 / 92 89 80
Fax +49 (0) 71 53 / 92 89 81
[email protected]
Ulm
Günter Wilhelm
Allgäuer Str. 7
89269 Vöhringen
Phone +49 (0) 73 06 / 92 46 08
Fax +49 (0) 73 06 / 92 46 48
[email protected]
External Support Manager
drive engineering
Office East
Dipl.-Ing. (TU) Michael Hanning
Lerchenweg 4
06120 Lieskau bei Halle
Phone +49 (0) 3 45 / 5 51 24 56
Fax +49 (0) 3 45 / 5 51 24 57
[email protected]
Office North
Ingenieurbüro Breuell GmbH
Elektro.-Ing. Dirk Kahl
Grützmühlenweg 40
22339 Hamburg
Phone +49 (0) 40 / 53 80 92 55
Fax +49 (0) 40 / 53 80 92 84
[email protected]
Office West
Matthias Bembenek
Prozessionsweg 39
46286 Dorsten
Phone +49 (0) 23 69 / 20 82 05
Fax +49 (0) 23 69 / 20 82 07
[email protected]
Office South-West
Thomas Schrag
Mahlbergstr. 37/1
75210 Keltern
Phone +49 (0) 72 36 / 98 24 07
Fax +49 (0) 72 36 / 98 24 09
[email protected]
Office South-Ost
Jürgen Sopejstal
Kirchhoffstr. 26
90552 Röthenbach
Phone +49 (0) 9 11 / 5 44 38 15
Fax +49 (0) 9 11 / 5 44 38 16
[email protected]
Service and Consulting Center for
sales of small quantities
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 40
22339 Hamburg
Phone +49 (0) 40 / 53 80 92 20
Fax +49 (0) 40 / 53 80 92 84
[email protected]
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Westbahnstr. 5
A-4490 St. Florian
Phone +43 / 7224 / 66 011-0
Fax +43 / 7224 / 66 011-20
[email protected]; www.ebmpapst.at
37
Motors Distributors
spec. Motors Distributors
Distributors of ebm-papst
Fans Distributors
Ventilator Distributors
next system
Vertriebsges. m.b.H.
Dresdner Str. 68/1/3
A-1200 Wien
Phone +43 / 1 / 33 166-0
Fax +43 / 1 / 33 166-100
[email protected]; www.nextsystem.at
Great Britain
ebm-papst UK Ltd.
Chelmsford Business Park
GB-Chelmsford Essex CM2 5EZ
Phone +44 / 12 45 / 46 85 55
Fax +44 / 12 45 / 46 63 36
[email protected]; www.ebmpapst.co.uk
Macedonia
ebm-papst Industries Kft.
Mátyás u. 1/A
H-2220 Vecsés
Phone +36 / 29 / 55 01 90
Fax +36 / 29 / 55 01 94
[email protected]; www.ebmpapst.hu
Belarus
ebm-papst Bel AgmbH
Prospekt Nesavisimosti 11/2
Suite 325, 512
BY-220050 Minsk
Phone +3 75 / 17 / 2 09 95 61
Fax. +375 / 17 / 2 09 95 61
[email protected]; www.ebmpapst.ru
ebm-papst Automotive & Drives (UK) Ltd
The Smithy, Fidlers Lane
East Ilsley, Newbury
Berkshire RG20 7LG
Phone +44 / 87 07 / 66 51 70
Fax +44 / 87 07 / 66 51 80
A&[email protected]; www.ebmpapst.co.uk
Netherlands
VIBO Benelux B. V.
Engelseweg 127
Postbus 230
NL-5705 AC Helmond
Phone +31 / 4 92 / 50 29 00
Fax +31 / 4 92 / 50 29 50
[email protected];
www.vibobenelux.com
Belgium
VIBO Benelux B. V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
B-3001 Heverlee-Leuven
Phone +32 / 16 / 39 62 00
Fax +32 / 16 / 39 62 20
[email protected]
www.vibobenelux.com
Bulgaria see also Romania
Croatia see also Hungary
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Krátká 379
CZ-66461 Rajhradice u Brna
Phone +4 20 / 5 / 47 23 26 16
Fax +4 20 / 5 / 47 23 26 22
[email protected]; www.ebmpapst.com
Denmark
Jenk ApS
Vallensbækvej 21
DK-2605 Brøndby
Phone +45 / 43 63 11 11
Fax +45 / 43 63 05 05
[email protected]; www.jenk.dk
Finland
ebm-papst OY
Puistotie 1
FIN-02760 Espoo
Phone +358 / 9 / 88 70 22 0
Fax +358 / 9 / 88 70 22 13
[email protected]; www.ebmpapst.fi
France
ebm-papst sarl
BP 62
F-67212 Obernai-Cedex
Phone +33 / 820 326 266
Fax +33 / 3 / 88 67 38 83
[email protected]; www.ebmpapst.fr
38
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
GR-17672 Kallithea-Attiki
Phone +30 / 2 10 / 9 51 37 05
Fax +30 / 2 10 / 9 51 34 90
[email protected]; www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Mátyás u. 1/A
H-2220 Vecsés
Phone +36 / 29 / 55 01 90
Fax +36 / 29 / 55 01 94
[email protected]; www.ebmpapst.hu
Iceland
RJ Engineers
Stangarhyl 1A
IS-110 Reykjavik
Phone +354 / 567 80 30
Fax +354 / 567 80 15
[email protected]; www.rj.is
Ireland
ebm-papst Ltd.
Portlaoise Business & Technology Park
Mountrath Road
IRL-Portlaoise, Co. Laois
Phone +353 / 8 66 43 43
Fax +353 / 8 66 43 46
[email protected]; www.ebmpapst.ie
Italy
ebm-papst S.r.l.
Via Cornaggia 108
I-22076 Mozzate (Co)
Phone +39 / 03 31 / 83 62 01
Fax +39 / 03 31 / 82 15 10
[email protected]; www.ebmpapst.it
Norway
ebm-papst AS
Nordasveien 5
N-1203 Oslo
Phone +47 / 22 / 76 33 40
Fax +47 / 22 / 61 91 73
[email protected]; www.ebmpapst.no
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
PL-03-236 Warszawa
Phone +48 / 22 / 675 78 19
Fax +48 / 22 / 676 95 87
[email protected]; www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda
Av. Marechal Gomes da Costa, 35 e
Rua Conselheiro Emidio Navarro
P-1800-255 Lisboa
Phone +351 / 21 / 839 48 80
Fax +351 / 21 / 839 47 59
[email protected]; www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tirnavei No. 20
RO-500327 Brasov
Phone +40 / 2 68 / 31 28 05
Fax +40 / 2 68 / 31 28 05
[email protected]
Russia
ebm-papst Ural GmbH
Posadskaya 23
4. Floor, Suite 403
RUS-620102 Jekaterinburg
Phone +7 / 343 / 233 77 85
Fax +7 / 343 / 233 77 99
[email protected]
www.ebmpapst.ur.ru
Motors Distributors
spec. Motors Distributors
Distributors of ebm-papst
Fans Distributors
Ventilators Distributors
ebm-papst Rus GmbH
Nizhegorodskaya 32, str. 15 office 420
RU-109029 Moskau
Phone +7 / 4 95 / 6 71 53 93
Fax +7 / 4 95 / 6 71 53 95
[email protected]; www.ebmpapst.ru
ebm-papst Rus
Saint-Petersburg´s Filial
Zastavskaya 7
RU-196084 Sankt-Petersburg
Phone +7 / 8 12 / 4 49 96 07
Fax +7 / 8 12 / 4 49 96 07
[email protected]
Serbia & Montenegro
ebm-papst Industries Kft.
Mátyás u. 1/A
H-2220 Vecsés
Phone +36 / 29 / 55 01 90
Fax +36 / 29 / 55 01 94
[email protected]; www.ebmpapst.hu
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
C/Monton de Trigo, Nr. 3
E-28830 San Fernando
de Henares (Madrid)
Phone +34 / 91 / 6 78 08 94
Fax +34 / 91 / 6 78 15 30
[email protected]
Sweden
ebm-papst AB
Äggelundavägen 2
S-17562 Järfälla
Phone +46 / 8 / 7 61 94 00
Fax +46 / 8 / 36 23 06
[email protected]; www.ebmpapst.se
Switzerland
ebm-papst AG
Rütisbergstraße 1
CH-8156 Oberhasli
Phone +41 / 44 / 732 20 70
Fax +41 / 44 / 732 20 77
[email protected]; www.ebmpapst.ch
Omni Ray AG
Im Schörli 5
CH-8600 Dübendorf
Phone +41 / 44 / 8 02 28 80
Fax +41 / 44 / 8 02 28 28
[email protected]; www.omniray.ch
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
TR-35620 Cigli-Izmir
Phone +90 / 2 32 / 32 82 090 -91
Fax +90 / 2 32 / 32 80 270
[email protected]; www.akantel.com.tr
USA
ebm-papst Inc.
100 Hyde Road
USA-Farmington, CT 06034
Phone +1 / 860 / 674 15 15
Fax +1 / 860 / 674 85 36
[email protected]; www.ebmpapst.us
Ukraine
ebm-papst Ukraine GmbH
Lepse Boulevard 4, House 47 Floor 5
UA-03067 Kiev
Phone +38 / 0 44 / 2 06 30 91
Fax +38 / 0 44 / 2 06 30 91
[email protected]; www.ebm-papst.ua
ebm-papst Automotive and Drives, Inc.
3200 Greenfield, Suite 255
Dearborn, MI 48120
Phone +1 / 313 / 406 80 80
Fax +1 / 313 / 406 80 81
[email protected];
www.ebmpapst-automotive.us
Americas
Africa
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
1752 Buenos Aires
Phone +54 / 11 46 57-61 35
Fax +54 / 11 46 57-20 92
[email protected]
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Ave.
ZA-2040 Honeydew Ext. 20
Phone +27 / 11 / 794 57 06
Fax +27 / 11 / 794 50 20
[email protected]; www.ebmpapst.co.za
Brazil
ebm-papst Motores Ventiladores Ltda.
Rua Francisco D´Amico, 155
Bairro Pirajussara
BR-06707-100 Taboão da Serra-SP
Phone +55 /11 / 31 64 89 00
Fax +55 /11 / 41 38 50 86
[email protected];
www.ebmpapst.com.br
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
CDN-Pickering, Ontario, L1W3J9
Phone +1 / 905 / 420 / 35 33
Fax +1 / 905 / 420 / 37 72
[email protected]; www.ebmpapst.ca
Mexico
ebm Industrial S.de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
MEX-Mexico 05120, D.F.
Phone +52 / 55 / 50 91 44 44
Fax +52 / 55 / 50 91 44 43
[email protected];
www.ebmpapst.com.mx
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Hua Jing Road
Wai Gao Qiao Free Trade Zone
No. 2001, Yang Gao (N) Road
200131 Shanghai, P.R. of China
Phone +86 / 21 / 50 46 01 83
Fax +86 / 21 / 50 46 11 19
[email protected];
www.ebmpapst.com.cn/
Hong Kong
ebm-papst Ventilator (Shanghai) Co., Ltd.
Hong Kong Representative Office
Unit Nos. 13-15, 9/F, Technology Park
18 On Lai Street, Sha Tin
N.T. Hong Kong, P.R: of China
Phone +852 / 21 45 / 86 78
Fax +852 / 21 45 / 76 78
[email protected]
39
M 1094 GB 2.0408
Subject to technical modifications.
Printed in Germany
ebm-papst
St. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
D-78112 ST. GEORGEN
Germany
Phone +49 (0) 7724 / 81-0
Fax +49 (0) 7724 / 81-1309
[email protected]
www.ebmpapst.com