ECI Motor ECI-80.60-K1 - Highly dynamic 3-phase internal rotor motor with EC technology - Robust, noise-optimized ball bearing system for a long service life - Mechanical design and interfaces designed for modular flexibility - High efficiency and high power density realized in a compact design -B asic motor with electronic module K1 for operation with external drive electronics - Protection rating IP 40 / IP 54 and connection by connector system Nominal data Type ECI-80.60-K1 D00 Nominal voltage (UN) VDC 48 Nominal speed (nN)** rqm 4000** Nominal torque (M N)** mNm 1800** Nominal current (I N)** A 18** Nominal output power (PN)** W 754** Free-running speed (nL) –1 min 6100 Permanent holding torque (M NO) mNm 1800 Permiss. peak current (Imax)*** A 100*** Motor constant (KE) mVs/rad 72.15 Terminal resistance (R V) Ω 0.04 Terminal inductance (L V) mH 0.2 Starting torque (Mmax) mNm 5600 Ambient temperature range (TU) °C -30...+40 Rotor moment of inertia (J R) kgm2 x10–6 155 Motor mass (m) kg 2.7 Order number (IP 40) Wire interface 932 8060 105 Order number (IP 54)* Connector interface on request subject to alterations * Classification of protection class reters to installed state with sealing on the flange side ** At TU max. 40 °C / 104 °F *** Permissible time for peak current: max. 5 sec.- to be repeated only after complete cool down F radial F axial Faxial 280 N Permissible shaft load at nominal speed and Fradial 280 N life expectancy L10 of 20 000 h** L 1 = 20 mm L1 ECI-80.60-K1-D00, 48V (at 25°C / 77° F) 6500 Mn 6000 Mmax 120 100 5000 Speed n [min-1] 4500 4000 80 Operating point 1) 3500 3000 60 2500 2000 40 1500 1000 0 0 500 1000 1500 n = Speed, f (M) 1) 20 Continuous operation 500 Short-time operation 2000 2500 3000 3500 Torque M [mNm] I = Current, f (M) 4000 4500 Current I [A]; Efficiency η [%] 5500 0 5000 5500 η = Efficiency, f (M) Nominal data, see table above V4_07/2015 ECI_80.60_K1_EN_V4.indd 1 14.07.2015 16:37:46 ECI Motor ECI-80.60-K1 Technical drawing M6 Screw depth = 13 mm M5 Screw depth = 13 mm M6 Screw depth = 13 mm Tapped blind holes for thread-forming screws in accordance to DIN 7500. Tightening torque: M5 6 ± 0.2 Nm M6 10 ± 0.2 Nm Accessory (must be ordered separatly) Connection description Motor (IP 40 version) Sensor cable with wires and plug AWG 24 (0.22 mm2) Picture 1 = with cover (simplyfied design) Picture 2 = cover removed (simplyfied design) Cable outlet sensor cable Socket for sensor cable Type Order number Sensor cable 992 0800 001 motor side Winding connector AWG 12 (4 mm2) Type Colour Order number Power wire L1 brown 992 0800 012 Power wire L2 purple 992 0800 011 Power wire L3 yellow 992 0800 010 motor side L1 L3 L2 Tightening torque: M3 1.5 ± 0.2 Nm Possible gearbox variants Recommended external control electronics Type Type Order number on request VT-MI-35 992 0801 035 ECI_80.60_K1_EN_V4.indd 2 14.07.2015 16:37:52