AK8181B

AK8181B
3.3V LVPECL 1:4
Clock Fanout Buffer
AK8181B
Features
Description
The AK8181B is a member of AKM’ｓ LVPECL
clock fanout buffer family designed for telecom,
networking and computer applications, requiring a
range of clocks with high performance and low
skew. The AK8181B distributes 4 buffered
clocks.
Four differential 3.3V LVPECL outputs
Selectable LVTTL/LVCMOS CLK or crystal
input
Clock output frequency up to 266MHz
Output skew : 10ps typical
Part-to-part skew : 200ps maximum
Propagation delay : 1.4ns maximum
Additive phase jitter(RMS) : 0.057ps(typical)
Operating Temperature Range: -40 to +85°C
Package: 20-pin TSSOP (Pb free)
Pin compatible with ICS8535I-31
AK8181B are derived from AKM’ｓ long-termexperienced clock device technology, and enable
clock output to perform low skew. The AK8181B
is available in a 20-pin TSSOP package.
Block Diagram
MS1417-E-02
Dec-2012
-1-
AK8181B
Pin Descriptions
Package: 20-Pin TSSOP (Top View)
Pin No.
1
Pin Name
VSS
Pin
Type
Pullup
down
PWR
--
2
CLK_EN
IN
Pull up
3
CLK_SEL
IN
Pull down
Description
Negative power supply
Synchronizing clock output enable (LVCMOS/LVTTL)
Pin is connected to VDD by internal resistor. (typ. 51kΩ
High (Open): clock outputs follow clock input.
Low: Q outputs are forced low, Qn outputs are forced high.
CLK Select Input (LVCMOS/LVTTL)
Pin is connected to VSS by internal resistor. (typ. 51kΩ
High: selects XTAL input
Low (Open): selects CLK input
LVCMOS/LVTTL Clock Input
Pin is connected to VSS by internal resistor. (typ. 51kΩ
4
CLK
IN
Pull down
5
NC
--
--
6
XTAL_IN
IN
--
7
XTAL_OUT
OUT
--
*When using CLK input (CLK_SEL=Low), it should be connected to
VSS or opened.
8
NC
--
--
No connect
*When using crystal input (CLK_SEL=High), it should be connected
to VSS or opened.
No connect
Crystal oscillator interface
*When using CLK input (CLK_SEL=Low), it should be connected to
VSS or opened.
Crystal oscillator interface
9
NC
--
--
No connect
10
VDD
PWR
--
Positive power supply
11, 12
Q3n, Q3
OUT
--
Differential clock output (LVPECL)
13
VDD
PWR
--
Positive power supply
14, 15
Q2n, Q2
OUT
--
Differential clock output (LVPECL)
16, 17
Q1n, Q1
OUT
--
Differential clock output (LVPECL)
18
VDD
PWR
--
Positive power supply
19, 20
Q0n, Q0
OUT
--
Differential clock output (LVPECL)
Ordering Information
Part Number
Marking
Shipping
Packaging
Package
Temperature
Range
AK8181B
AK8181B
Tape and Reel
20-pin TSSOP
-40 to 85 °C
Dec-2012
MS1417-E-02
-2-
AK8181B
Absolute Maximum Rating
Over operating free-air temperature range unless otherwise noted
Items
Supply voltage
Input voltage
(2)
Symbol
Ratings
Unit
VDD
-0.3 to 4.6
V
Vin
-0.5 to VDD+0.5
V
IIN
±10
mA
Tstg
-55 to 150
C
(2)
Input current (any pins except supplies)
Storage temperature
(1)
Note
(1) Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only. Functional operation of the device at these or any other conditions beyond those
indicated under “Recommended Operating Conditions” is not implied. Exposure to absolute-maximum-rating
conditions for extended periods may affect device reliability. Electrical parameters are guaranteed only over the
recommended operating temperature range.
(2) VSS=0V
ESD Sensitive Device
This device is manufactured on a CMOS process, therefore, generically susceptible to
damage by excessive static voltage. Failure to observe proper handling and
installation procedures can cause damage. AKM recommends that this device is handled with
appropriate precautions.
Recommended Operation Conditions
Parameter
Operating temperature
Supply voltage
(1)
Symbol
Conditions
Ta
VDD
Min
Typ
-40
VDD5%, VSS=0V
(1) Power of 3.3V requires to be supplied from a single source.
be located close to each VDD pin.
3.135
3.3
Max
Unit
85
C
3.465
V
A decoupling capacitor of 0.1μF for power supply line should
Pin Characteristics
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Input Capacitance
CIN
4
pF
Input Pullup Resistor
RPU
51
kΩ
Input Pulldown Resistor
RPD
51
kΩ
MS1417-E-02
Dec-2012
-3-
AK8181B
DC Characteristics
All specifications at VDD= 3.3V5%, VSS=0V, Ta: -40 to +85°C, unless otherwise noted
Parameter
Symbol
Input High Voltage
VIH
Input Low Voltage
VIL
CLK, CLK_SEL
Input
High Current CLK_EN
Input
Low Current
IH
IL
CLK_EN
(1)
MIN
TYP
2.0
MAX
Unit
VDD+0.3
V
0.8
V
Vin=VDD=3.465V
-0.3
150
μA
Vin=VDD=3.465V
5
μA
Vin=VSS,
CLK, CLK_SEL
Output High Voltage
Conditions
VDD=3.465V
Vin=VSS,
VDD=3.465V
-5
μA
-150
μA
VOH
VDD-1.4
VDD-0.9
V
VOL
VDD-2.0
VDD-1.7
V
VSWING
0.6
1.0
V
60
mA
MAX
Unit
50
MHz
Equivalent Series Resistance (ESR)
50
Ω
Shunt Capacitance
7
pF
Drive Level
1
mW
Output Low Voltage
(1)
Peak-to-Peak Output
Voltage Swing
Supply Current
IDD
(1) Outputs terminated with 50Ω to VDD-2V.
Crystal Characteristics
All specifications at VDD= 3.3V5%, VSS=0V, Ta: -40 to +85°C, unless otherwise noted
Parameter
Conditions
MIN
Mode of Oscillation
TYP
Fundamental
Frequency
12
Dec-2012
MS1417-E-02
-4-
AK8181B
AC Characteristics
All specifications at VDD= 3.3V5%, VSS=0V, Ta: -40 to +85°C, unless otherwise noted
Parameter
Symbol
Output Frequency
Propagation Delay
MIN
tPD
(2)(3)
0.6
tsk(O)
(3)(5)
Part-to-Part Skew
Output Rise/Fall Time
(4)
tr , tf
MAX
Unit
266
MHz
1.4
ns
10
tskPP
Buffer Additive Jitter, RMS tjit
Output Duty Cycle
TYP
fOUT
(1)
Output Skew
(1)
(2)
(3)
(4)
(5)
Conditions
ps
200
155.52MHz (12kHz – 20MHz)
20% to 80%
0.057
200
DCOUT
ps
46
50
ps
600
ps
54
%
Measured from the VDD/2 of the input to the differential output crossing point.
Defined as skew between outputs at the same supply voltage and with equal load conditions.
This parameter is defined in accordance with JEDEC Standard 65.
Design value.
Defined as skew between outputs on different devices operating at the same supply voltages and with equal load
conditions. Using the same type of inputs on each device, the outputs are measured at the differential cross points.
MS1417-E-02
Dec-2012
-5-
AK8181B
Parameter Measurement Information
Figure 1 3.3V Output Load Test Circuit
Figure 2 Part-to-Part Skew
Qxn
80%
Clock
Outputs
Qx
Qyn
80%
VSWING
20%
20%
tR
tF
Qy
tsk(o)
Figure 3 Output Skew
Figure 4 Output Rise/Fall Time
Figure 5 Propagation Delay
Figure 6 Output Duty/ Pulse Width/ Period
Dec-2012
MS1417-E-02
-6-
AK8181B
Function Table
The following table shows the inputs/outputs clock state configured through the control pins.
Table 1: Control Input Function Table
Inputs
Outputs
CLK_EN
CLK_SEL
Selected Source
Q0:Q3
Q0n:Q3n
0
0 (Open)
CLK
Disabled: Low
Disabled: High
0
1
Disabled: Low
Disabled: High
1 (Open)
0 (Open)
Enabled
Enabled
1 (Open)
1
Enabled
Enabled
XTAL_IN,
XTAL_OUT
CLK
XTAL_IN,
XTAL_OUT
After CLK_EN switches, the clock outputs are disabled or enabled following a rising and falling input clock or
crystal oscillator edge as shown in Figure 7. In the active mode, the state of the outputs are a function of the CLK
input as described in Table 2.
Figure 7 CLK_EN Timing Diagram
Table 2 Clock Input Function Table
Inputs
Outputs
CLK
Q0 : Q3
Q0n : Q3n
0
Low
High
1
High
Low
MS1417-E-02
Dec-2012
-7-
AK8181B
Package Information
 Mechanical data : 20pin TSSOP
6.50±0.10
0.15±0.05
11
1
6.40±0.10
4.40±0.10
0.6±0.10
20
10
0.25±0.05
0.65
0°～8°
S
S
1.10 MAX
0.10
0.10±0.05
0.90±0.05
 Marking
20
11
b
AK8181B
XXXXXXX
c
a:
b:
c:
#1 Pin Index
Part number
Date code ( 7 digits)
a
10
1
 RoHS Compliance
All integrated circuits form Asahi Kasei Microdevices Corporation (AKM)
assembled in “lead-free” packages* are fully compliant with RoHS.
(*) RoHS compliant products from AKM are identified with “Pb free” letter indication on
product label posted on the anti-shield bag and boxes.
Dec-2012
MS1417-E-02
-8-
AK8181B
IMPORTANT NOTICE
 These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei
Microdevices Corporation (AKM) or authorized distributors as to current status of the products.
 Descriptions of external circuits, application circuits, software and other related information contained in this
document are provided only to illustrate the operation and application examples of the semiconductor products. You
are fully responsible for the incorporation of these external circuits, application circuits, software and other related
information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third
parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent,
intellectual property, or other rights in the application or use of such information contained herein.
 Any export of these products, or devices or systems containing them, may require an export license or other official
approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange,
or strategic materials.
 AKM products are neither intended nor authorized for use as critical components Note1) in any safety, life support, or
other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use
approved with the express written consent by Representative Director of AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to result,
whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it,
and which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety
or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or
perform may reasonably be expected to result in loss of life or in significant injury or damage to person or
property.
 It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places
the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer
or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all
claims arising from the use of said product in the absence of such notification.
MS1417-E-02
Dec-2012
-9-