HS-2100RH Data Sheet Radiation Hardened High Frequency Half Bridge Driver The Radiation Hardened HS-2100RH is a high frequency, 100V Half Bridge N-Channel MOSFET Driver IC, which is a functional, pin-to-pin replacement for the Intersil HIP2500 and the industry standard 2110 types. The low-side and high-side gate drivers are independently controlled. This gives the user maximum flexibility in dead-time selection and driver protocol. In addition, the device has on-chip error detection and correction circuitry, which monitors the state of the high-side latch and compares it to the HIN signal. If they disagree, a set or reset pulse is generated to correct the high-side latch. This feature protects the high-side latch from SEUs. Undervoltage on the high-side supply forces HO low. When that supply returns to a valid voltage, HO will go to the state of HIN. Undervoltage on the low-side supply forces both LO and HO low. When that supply becomes valid, LO returns to the LIN state and HO returns to the HIN state. Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed here must be used when ordering. Detailed Electrical Specifications for the HS-2100RH are contained in SMD 5962-99536. A “hot-link” is provided on our homepage for downloading. www.intersil.com/spacedefense/space.asp June 1999 File Number 4562.3 Features • Electrically Screened to DESC SMD # 5962-99536 • QML Qualified per MIL-PRF-38535 Requirements • Radiation Environment - Maximum Total Dose . . . . . . . . . . . . . . 3 x 105 RAD(SI) - DI RSG Process Provides Latch-up Immunity - Vertical Architecture Provides Low Dose Rate Immunity • Bootstrap Supply Max Voltage to 120V • Drives 1000pF Load at 1MHz with Rise and Fall Times of 45ns (Typ) • 1A (Typ) Peak Output Current • Independent Inputs for Non-Half Bridge Topologies • Low DC Power Consumption . . . . . . . . . . . . . 60mW (Typ) • Operates with VDD = VCC Over 12V to 20V Range • Supply Undervoltage Protection Applications • High Frequency Switch-Mode Power Supplies • Drivers for Inductive Loads • DC Motor Drivers Pinout HS-2100RH FLATPACK (CDFP4-F16) TOP VIEW This link will not be available until the SMD is finalized. Ordering Information ORDERING NUMBER 5962F9953601VXC 5962F9953601QXC HS9-2100RH/Proto INTERSIL MKT. NUMBER HS9-2100RH-Q HS9-2100RH-8 HS9-2100RH/Proto 1 LO 1 16 NC COM 2 15 VSS VCC 3 14 LIN -55 to 125 NC 4 13 SD -55 to 125 NC 5 12 HIN VS 6 11 VDD VB 7 10 NC HO 8 9 NC TEMP. RANGE (oC) -55 to 125 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 HS-2100RH Die Characteristics DIE DIMENSIONS: Backside Finish: 4710µm x 3570µm (186 mils x 141 mils) Thickness: 483µm ±25.4µm (19 mils ±1 mil) INTERFACE MATERIALS: Silicon ASSEMBLY RELATED INFORMATION: Substrate Potential: Glassivation: Unbiased (DI) Type: PSG (Phosphorous Silicon Glass) Thickness: 8.0kÅ ±1.0kÅ ADDITIONAL INFORMATION: Worst Case Current Density: Top Metallization: <2.0 x 105 A/cm2 Type: ALSiCu Thickness: 16.0kÅ ±2kÅ Transistor Count: Substrate: 125 Radiation Hardened Silicon Gate, Dielectric Isolation Metallization Mask Layout HS-2100RH SD (13) HIN (12) LIN (14) VDD (11) VSS (15) HO (8) LO (1) COM (2) VB (7) VCC (3) VS (6) All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com 2