HS-1825ARH TM Data Sheet July 2001 Radiation Hardened High-Speed, Dual Output PWM File Number Features • Electrically Screened to DESC SMD # 5962-99558 The Radiation Hardened HS-1825ARH Pulse Width Modulator is designed to be used in high frequency switched-mode power supplies and can be used in either current-mode or voltage-mode. It is well suited for singleended boost converter applications. • QML Qualified per MIL-PRF-38535 Requirements Device features include a precision voltage reference, low power start-up circuit, high frequency oscillator, wide-band error amplifier, and fast current-limit comparator. The use of proprietary process capabilities and unique design techniques results in fast propagation delay times and high output current over a wide range of output voltages. • Radiation Environment - Maximum Total Dose . . . . . . . . . . . . . . . . 300 krad(SI) - Vertical Architecture Provides Low Dose Rate Immunity - DI RSG Process Provides Latch-Up Immunity • Low Start-Up Current . . . . . . . . . . . . . . . . . . . 100µA (Typ) • Fast Propagation Delay . . . . . . . . . . . . . . . . . . 80ns (Typ) • 12V to 30V Operation • 1A (Peak) Dual Output Drive Capability Constructed with the Intersil Rad Hard Silicon Gate (RSG) Dielectric Isolation BiCMOS process, the HS-1825ARH has been specifically designed to provide highly reliable performance when exposed to harsh radiation environments. • 5.1V Reference Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed below must be used when ordering. • Trimmed Oscillator Discharge Current Detailed Electrical Specifications for the HS-1825ARH are contained in SMD 5962-99558. That document may be easily downloaded from our website. www.intersil.com/spacedefense/space.asp • Programmable Leading Edge Blanking Circuit Ordering Information • Motor Speed and Direction Control ORDERING NUMBER INTERSIL MKT. NUMBER TEMP. RANGE (oC) • Under-Voltage Lockout • Programmable Soft-Start • Switching Frequencies to 500kHz • Latched Overcurrent Comparator with Full Cycle Restart Applications • Current or Voltage Mode Switching Power Supplies Pinout HS-1825ARH SBDIP (CDIP2-T16) AND FLATPACK (CDFP4-F16) TOP VIEW 5962F9955801VEC HS1-1825ARH-Q -50 to 125 5962F9955801QEC HS1-1825ARH-8 -50 to 125 5962F9955801VXC HS9-1825ARH-Q -50 to 125 INV 1 5962F9955801QXC HS9-1825ARH-8 -50 to 125 NON-INV 2 15 VCC E/A OUT 3 14 OUTPUT B HS1-1825ARH/Proto HS1-1825ARH/Proto -50 to 125 HS9-1825ARH/Proto HS9-1825ARH/Proto -50 to 125 4561.6 CLOCK 4 16 VREF 5.1V 13 VC RT 5 12 POWER GND CT 6 11 OUTPUT A RAMP 7 SOFT START 8 10 GND 9 ILIM/SD NOTE: Grounding the Soft Start pin does not inhibit the outputs. The outputs may be inhibited by applying >1.26V to the ILIM/SD pin. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2001, All Rights Reserved HS-1825ARH Die Characteristics DIE DIMENSIONS 4710µm x 3570µm (185 mils x 140 mils) Thickness: 483µm ±25.4µm (19 mils ±1 mil) Backside Finish Silicon ASSEMBLY RELATED INFORMATION INTERFACE MATERIALS Substrate Potential Glassivation Type: PSG (Phosphorous Silicon Glass) Thickness: 8.0kÅ ±1.0kÅ Unbiased (DI) ADDITIONAL INFORMATION Top Metallization Type: ALSiCu Thickness: 16.0kÅ ±2kÅ Worst Case Current Density <2.0 x 105 A/cm 2 Substrate Radiation Hardened Silicon Gate, Dielectric Isolation Metallization Mask Layout Transistor Count 225 HS-1825ARH (4) CLK/LEB RT (5) (3) EAOUT CT (6) (2) IN+ RAMP (7) (1) INSS (8) (16) VREF ILIM (9) OSCGND (NOTE 1) (15) VCC GND (10) (14) OUTB OUTA (11) (12) PGND (NOTE 2) PGND (12) (NOTE 2) (13) VC (NOTE 2) VC (13) (NOTE 2) NOTES: 1. This is the oscillator ground (OSCGND) bond pad and must be connected to GND. 2. PGND and VC each require two bond pad connections. All Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation 7585 Irvine Center Drive Suite 100 Irvine, CA 92618 TEL: (949) 341-7000 FAX: (949) 341-7123 Intersil Corporation 2401 Palm Bay Rd. Palm Bay, FL 32905 TEL: (321) 724-7000 FAX: (321) 724-7946 2 EUROPE Intersil Europe Sarl Ave. C - F Ramuz 43 CH-1009 Pully Switzerland TEL: +41 21 7293637 FAX: +41 21 7293684 ASIA Intersil Corporation Unit 1804 18/F Guangdong Water Building 83 Austin Road TST, Kowloon Hong Kong TEL: +852 2723 6339 FAX: +852 2730 1433