AK4633EN

ASAHI KASEI
[AKD4633-A]
AKD4633-A
AK4633 Evaluation board Rev.3
GENERAL DESCRIPTION
AKD4633-A is an evaluation board for the AK4633VN, 16bit mono CODEC with MIC/SPK amplifier. The
AKD4633-A can evaluate A/D converter and D/A converter separately in addition to loopback mode (A/D
→ D/A). AKD4633-A also has the digital audio interface and can achieve the interface with digital audio
systems via opt-connector.
„ Ordering guide
AKD4633-A
--- Evaluation board for AK4633VN
(Cable for connecting with printer port of IBM-AT, compatible PC and control
software are packed with this. This control software does not support Windows NT.)
FUNCTION
• DIT/DIR with optical input/output
• BNC connector for an external clock input
• 10pin Header for serial control mode
5V
AVDD DVDD SVDD
3.3V
Regulator
GND
MIC-Jack
Control Data
MIC
10pin Header
BEEP/MIN/MOUT
AOUT
DSP
AK4633VN
10pin Header
SPK-Jack
AK4114
Opt In
Opt Out
Clock
Gen
Figure 1. AKD4633-A Block Diagram
* Circuit diagram and PCB layout are attached at the end of this manual.
<KM079406>
2007/04
-1-
ASAHI KASEI
[AKD4633-A]
Evaluation Board Manual
„ Operation sequence
1) Set up the power supply lines.
1-1) When AVDD, DVDD, SVDD, and VCC are supplied from the regulator. (AVDD, DVDD, SVDD, and
VCC jack should be open.). See “Other jumper pins set up (page 10)”. <default>
[REG]
[AVDD]
[DVDD]
[SVDD]
[VCC]
[AVSS]
[AGND]
[DGND]
(red )
(orange)
(orange)
(blue)
(orenge)
(black)
(black)
(black)
= 5V
= open
= open
= open
= open
= 0V
= 0V
= 0V
: 3.3V is supplied to AVDD of AK4633VN from regulator.
: 3.3V is supplied to DVDD of AK4633VN from regulator.
: 3.3V is supplied to SVDD of AK4633VN from regulator.
: 3.3V is supplied to logic block from regulator.
: for analog ground
: for analog ground
: for logic ground
1-2) When AVDD, DVDD, SVDD, and VCC are not supplied from the regulator. (AVDD, DVDD, SVDD, and
VCC jack should be junction.) See “Other jumper pins set up (page 10)”.
[REG]
[AVDD]
[DVDD]
[SVDD]
[VCC]
[AVSS]
[AGND]
[DGND]
(red)
(orange)
(orange)
(blue)
(orenge)
(black)
(black)
(black)
= “REG” jack should be open.
= 2.6 ∼ 3.6V : for AVDD of AK4633VN (typ. 3.3V)
= 2.6 ∼ 3.6V : for DVDD of AK4633VN (typ. 3.3V)
= 2.6 ∼ 5.25V : for SVDD of AK4633VN (typ. 3.3V, 5.0V)
= 2.6 ∼ 3.6V : for logic (typ. 3.3V)
= 0V
: for analog ground
= 0V
: for analog ground
= 0V
: for logic ground
Each supply line should be distributed from the power supply unit.
AVDD and DVDD must be same voltage level.
2) Set up the evaluation mode, jumper pins and DIP switches. (See the followings.)
3) Power on.
The AK4633VN and AK4114 should be reset once bringing SW1, 2 “L” upon power-up.
„ Evaluation mode
In case of AK4633VN evaluation using AK4114, it is necessary to correspond to audio interface format for
AK4633VN and AK4114. About AK4633VN’s audio interface format, refer to datasheet of AK4633VN.
About AK4114’s audio interface format, refer to Table 2 in this manual.
Applicable Evaluation Mode
(1) Evaluation of loop-back mode (A/D → D/A) : PLL, Master Mode
(2) Evaluation of loop-back mode (A/D → D/A) : PLL, Slave Mode (PLL Reference CLOCK: MCKI
pin)
(3) Evaluation of loop-back mode (A/D → D/A) : PLL, Slave Mode (PLL Reference CLOCK: BICK or
FCK pin)
(4) Evaluation of using DIR of AK4114 (opt-connector) : EXT, Slave Mode
(5) Evaluation of using DIT of AK4114 (opt-connector) : EXT, Slave Mode
<KM079406>
2007/04
-2-
ASAHI KASEI
[AKD4633-A]
(1) Evaluation of loop-back mode (A/D → D/A) : PLL, Master Mode
a) Set up jumper pins of MCKI clock
X’tal of 11.2896MHz, 12MHz, 12.288MHz, 13MHz, 24MHz or 27MHz can be set in X2. X’tal of 12.288MHz
(Default) is set on the AKD4633VN. Set “No.8 of SW3” to “H”.
When an external clock (11.2896MHz, 12MHz, 12.288MHz, 13MHz, 24MHz or 27MHz) through a RCA
connector (J8: EXT/BICK) is supplied, select EXT on JP21 (MCLK_SEL) and short JP17 (XTE). JP23 (EXT1)
and R26 should be properly selected in order to much the output impedance of the clock generator.
JP6
JP17
XTE
MCKI
JP18
MKFS
JP21
MCLK_SEL
XTL DIR EXT 256fs 512fs 1024fs MCKO
b) Set up jumper pins of BICK clock
Output frequency (16fs/32fs/64fs) of BICK should be set by “BCKO1-0 bit” in the AK4633VN.
There is no necessity for set up JP19.
JP20
BICK
INV
JP29
BICK_INV
JP27
BICK
DIR ADC
THR
INV
THR
JP19
BICK_SEL
64fs 32fs 16fs EXT
c) Set up jumper pins of FCK clock
JP28
FCK
JP22
FCK_SEL
DIR
ADC
2fs 1fs EXT
d) Set up jumper pins of DATA
When the AK4633VN is evaluated by loop-back mode (A/D → D/A), the jumper pins should be set to the
following.
JP30
JP26
4631_SDTI
SDTI
DIR
ADC
DAC/LOOP ADC
<KM079406>
2007/04
-3-
ASAHI KASEI
[AKD4633-A]
(2) Evaluation of loop-back mode (A/D → D/A) : PLL, Slave Mode (PLL Reference CLOCK: MCKI pin)
a) Set up jumper pins of MCKI clock
X’tal of 12.288MHz (Default) is set on the AKD4633-A. In this case, the AK4633VN corresponds to PLL
reference clock of 12.288MHz. In this evaluation mode, the output clock from MCKO-pin of the AK4633VN is
supplied to a divider (U3: 74VHC4040), BICK and FCK clocks are generated by the divider. Then “MCKO bit”
in the AK4633VN should be set to “1”. When an external clock through a RCA connector (J8: EXT/BICK) is
supplied, select EXT on JP21 (MCLK_SEL) and short JP17 (XTE). JP23 (EXT1) and R26 should be properly
selected in order to match the output impedance of the clock generator.
JP17
XTE
JP6
MCKI
JP18
MKFS
JP21
MCLK_SEL
XTL DIR EXT 256fs 512fs 1024fs MCKO
b) Set up jumper pins of BICK clock
JP20
BICK
INV
JP27
BICK
DIR ADC
THR
JP29
BICK_INV
INV
THR
JP19
BICK_SEL
64fs 32fs 16fs EXT
c) Set up jumper pins of FCK clock
JP22
FCK_SEL
JP28
FCK
DIR
ADC
2fs 1fs EXT
d) Set up jumper pins of DATA
When the AK4633VN is evaluated by loop-back mode (A/D → D/A), the jumper pins should be set to the
following.
JP30
JP26
4631_SDTI
SDTI
DIR
ADC
DAC/LOOP ADC
<KM079406>
2007/04
-4-
ASAHI KASEI
[AKD4633-A]
(3) Evaluation of loop-back mode (A/D → D/A) : PLL, Slave Mode (PLL Reference CLOCK: BICK or FCK
pin)
a) Set up jumper pins of BICK clock
When an external clock through a RCA connector J8 (EXT/BICK) is supplied, select EXT on JP19
(MCLK_SEL) and short JP17 (XTE). JP23 (EXT1) and R26 should be properly selected in order to match the
output impedance of the clock generator.
JP17
XTE
JP20
BICK
JP21
MCLK_SEL
XTL DIR EXT
INV
THR
JP29
BICK_INV
JP27
BICK
DIR ADC
INV
THR
In this evaluation mode, the selected clock from JP21 (MCLK_SEL) is supplied to a divider (U3: 74VHC4040),
BICK and FCK clocks are generated by the divider. Input frequency of master clock is set up in turn “256fs”,
“512fs”, “1024fs” from left.
JP18
MKFS
JP18
MKFS
JP18
MKFS
256fs 512fs 1024fs MCKO
256fs 512fs 1024fs MCKO
256fs 512fs 1024fs MCKO
And input frequency of BICK is set up in turn “16fs”, “32fs”, “64fs” from left.
JP19
BICK_SEL
JP19
BICK_SEL
JP19
BICK_SEL
64fs 32fs 16fs EXT
64fs 32fs 16fs EXT
64fs 32fs 16fs EXT
<KM079406>
2007/04
-5-
ASAHI KASEI
[AKD4633-A]
b) Set up jumper pins of FCK clock
When an external clock through a RCA connector J9 (FCK) is supplied, select EXT on JP22 (FCK_SEL). JP24
(EXT2) and R27 should be properly selected in order to match the output impedance of the clock generator.
JP22
FCK_SEL
JP28
FCK
DIR
ADC
2fs 1fs EXT
c) Set up jumper pins of DATA
When the AK4633VN is evaluated by loop-back mode (A/D → D/A), the jumper pins should be set to the
following.
JP30
JP26
4633_SDTI
SDTI
DIR
ADC
<KM079406>
DAC/LOOP ADC
2007/04
-6-
ASAHI KASEI
[AKD4633-A]
(4) Evaluation of using DIR of AK4114 (opt-connector) : EXT, Slave Mode
a) Set up jumper pins of MCKI clock
JP6
MCKI
JP21
MCLK_SEL
JP18
MKFS
XTL DIR EXT
256fs 512fs 1024fs
JP17
XTE
b) Set up jumper pins of BICK clock
JP20
BICK
INV
THR
JP29
BICK_INV
JP27
BICK
DIR ADC
INV
JP19
BICK_SEL
THR 64fs 32fs 16fs EXT
c) Set up jumper pins of FCK clock
JP24 (EXT2) and R27 should be properly selected in order to match the output impedance of the clock generator.
JP28
FCK
DIR
JP22
FCK_SEL
ADC
2fs 1fs EXT
d) Set up jumper pins of DATA
When D/A converter of the AK4633VN is evaluated by using DIR of AK4114, the jumper pins should be set to
the following.
JP30
JP26
4633_SDTI
SDTI
DIR
ADC
DAC/LOOP ADC
<KM079406>
2007/04
-7-
ASAHI KASEI
[AKD4633-A]
(5) Evaluation of using DIT of AK4114 (opt-connector) : EXT, Slave Mode
a) Set up jumper pins of MCKI clock
JP6
MCKI
JP21
MCLK_SEL
JP18
MKFS
XTL DIR EXT
256fs 512fs 1024fs
JP17
XTE
b) Set up jumper pins of BICK clock
JP20
BICK
INV
THR
JP27
BICK
DIR ADC
JP29
BICK_INV
INV
JP19
BICK_SEL
THR 64fs 32fs 16fs EXT
c) Set up jumper pins of FCK clock
JP24 (EXT2) and R27 should be properly selected in order to match the output impedance of the clock generator.
JP28
FCK
DIR
JP22
FCK_SEL
ADC
2fs 1fs EXT
d) Set up jumper pins of DATA
When A/D converter of the AK4633VN is evaluated by using DIR of AK4114, the jumper pins should be set to
the following.
JP30
JP26
4633_SDTI
SDTI
DIR
ADC
DAC/LOOP ADC
<KM079406>
2007/04
-8-
ASAHI KASEI
[AKD4633-A]
„ DIP Switch set up
[SW3] (MODE) : Mode Setting of AK4633-VN and AK4114
ON is “H”, OFF is “L”.
No.
Name
ON (“H”)
OFF (“L”)
1
DIF0
AK4114 Audio Format Setting
2
DIF1
See Table 2
3
DIF2
Clock Operation Mode select
4
CM0
See Table 3
5
CM1
6
OCKS0
Master Clock Frequency Select
See Table 4
7
OCKS1
8
M/S
Master mode
Slave mode
Note. When the AK4633VN is evaluated Master mode, “No.8 of SW3” is set to “H”.
Table 1. Mode Setting for AK4633VN and AK4114
Resistor setting
for AK4633VN Audio
Interface Format
Setting for AK4114 Audio Interface Format
DIF1 bit
DIF0 bit
DIF0
DIF1
DIF2
0
1
L
L
L
24bit, Left justified
16bit, Right justified
1
0
L
L
H
24bit, Left justified
24bit, Left justified
1
1
H
L
H
DAUX
SDTO
2
Default
2
24bit, I S
24bit, I S
Note. When the AK4633VN is evaluated by using DIR/DIT of AK4114, “No.8 of SW3” is set to “L”.
Table 2. Setting for AK4114 Audio Interface Format
Mode
0
1
CM1
0
0
CM0
0
1
UNLOCK
PLL
X'tal
Clock source SDTO
ON
ON(Note)
PLL
RX
OFF
ON
X'tal
DAUX
0
ON
ON
PLL
RX
2
1
0
Default
1
ON
ON
X'tal
DAUX
3
1
1
ON
ON
X'tal
DAUX
ON: Oscillation (Power-up), OFF: STOP (Power-down)
Note : When the X’tal is not used as clock comparison for fs detection (i.e. XTL1,0= “1,1”), the X’tal is off.
Default setting is recommended.
Table 3. Clock Operation Mode select
No.
0
2
OCKS1
0
1
MCKO1
256fs
512fs
MCKO2
256fs
256fs
X’tal
256fs
512fs
Default
Table 4. Master Clock Frequency Select (Stereo mode)
<KM079406>
2007/04
-9-
ASAHI KASEI
[AKD4633-A]
„ Other jumper pins set up
1. JP1 (GND)
OPEN
SHORT
: Analog ground and Digital ground
: Separated.
: Common. (The connector “DGND” can be open.) <Default>
2. JP2 (MICP)
MICP
BEEP
: Connection between MICP pin and BEEP pin of the AK4633VN.
: MIC Differential input.
: BEEP input. <Default>
3. JP3 (AVDD_SEL) : AVDD of the AK4633VN
REG
: AVDD is supplied from the regulator (“AVDD” jack should be open). < Default >
AVDD
: AVDD is supplied from “AVDD ” jack.
4. JP9 (DVDD_SEL) : DVDD of the AK4633VN
AVDD
: DVDD is supplied from “AVDD”. < Default >
DVDD
: DVDD is supplied from “DVDD ” jack.
5. JP10 (LVC_SEL) : Logic block of LVC is selected supply line.
DVDD
: Logic block of LVC is supplied from “DVDD”. < Default >
VCC
: Logic block of LVC is supplied from “VCC ” jack.
6. JP11 (VCC_SEL) : Logic block is selected supply line.
LVC
: Logic is supplied from supply line of LVC. < Default >
VCC
: Logic block of LVC is supplied from “VCC ” jack.
7. JP4 (SVDD_SEL) : SVDD of the AK4633VN
REG
: SVDD is supplied from the regulator (“SVDD” jack should be open). < Default >
SVDD
: SVDD is supplied from “SVDD ” jack.
8. JP8 (MCKO_SEL) : Master Clock Frequency is selected clock from MCKO1 or MCKO2 of the AK4114.
MCKO1
: The check from MCKO1 of AK4114 is provided to MCKI of the AK4633VN. < Default >
MCKO2
: The check from MCKO2 of AK4114 is provided to MCKI of the AK4633VN.
<KM079406>
2007/04
- 10 -
ASAHI KASEI
[AKD4633-A]
„ The function of the toggle SW
[SW1] (DIR)
: Power control of AK4114. Keep “H” during normal operation.
Keep “L” when AK4114 is not used.
[SW2] (PDN)
: Power control of AK4633VN. Keep “H” during normal operation.
„ Indication for LED
[LED1] (ERF): Monitor INT0 pin of the AK4114. LED turns on when some error has occurred to AK4114.
„ Serial Control
The AK4633VN can be controlled via the printer port (parallel port) of IBM-AT compatible PC. Connect PORT2
(CTRL) with PC by 10 wire flat cable packed with the AKD4633-A
Connect
PC
10 wire
flat cable
10pin
Connector
CSN
CCLK AKD4633-A
CDTI
10pin Header
Figure 2. Connect of 10 wire flat cable
<KM079406>
2007/04
- 11 -
ASAHI KASEI
[AKD4633-A]
„ Analog Input / Output Circuits
(1) Input Circuits
a) MIC Input Circuit
J1
MIC-JACK
6
4
3
AVSS
JP12
MIC_SEL
JACK
INT
J3
MIC
RCA
2
3
1
MR-552LS
AVSS
Figure 3. MIC Input Circuit
(a-1) Analog signal is input to MIC pin via J1 connector.
JP12
MIC_SEL
RCA JACK
(a-2) Analog signal is input to MIC pin via J3 connector.
JP12
MIC_SEL
RCA JACK
b) BEEP Input Circuit
J4
BEEP
2
C26
1u
R18
47k
MR-552LS
AVSS
R19
1
+
2
3
1
BEEP
20k
AVSS
Figure 4. BEEP Input Circuit
<KM079406>
2007/04
- 12 -
ASAHI KASEI
[AKD4633-A]
(2) Output Circuits
a) AOUT Output Circuit
1
AOUT
+
C28
R20
220
2
1u
J5 AOUT
2
3
1
R21
20k
MR-552LS
AVSS
AVSS
Figure 5. AOUT Output Circuit
b) SPK Output Circuit
Note. When mini-jack is inserted or pulled out J2 (SPK-JACK) connector, JP13 (SPP_SEL) and JP14
(SPN_SEL) should be open, or “PMSPK bit” in the AK4633VN should be set to “0”.
JP31
Dynamic
R15
10
3
4
SVSS
SPN
J2
SPK-JACK
6
JP13
D1
A
SVSS
K
DIODE ZENER
SVSS
K
DIODE ZENER
SPK1
SPN_SEL
JP14
D2
A
Dynamic(EXT)
Piezo(EXT)
Dynamic
CN5
Dynamic(EXT)
Piezo(EXT)
Dynamic
020S16
R
2
SPP_SEL
1
L
R17
10
SPP
Figure 6. SPK Output Circuit
(b-1) An external dynamic speaker is evaluated by using J2 (SPK-JACK) connector.
JP13
SPN_SEL
Dynamic
Dynamic(EXT)
Piezo(EXT)
JP14
SPP_SEL
JP31
Dynamic
Dynamic
Dynamic(EXT)
Piezo(EXT)
(b-2) An external Piezo speaker is evaluated by using J2 (SPK-JACK) connector.
<KM079406>
2007/04
- 13 -
ASAHI KASEI
[AKD4633-A]
JP13
SPN_SEL
Dynamic
Dynamic(EXT)
Piezo(EXT)
JP14
SPP_SEL
JP31
Dynamic
Dynamic
Dynamic(EXT)
Piezo(EXT)
(b-3) Analog signal of SPP/SPN pins are output from “Dynamic Speaker” on the evaluation (SPK1).
JP13
SPN_SEL
Dynamic
Dynamic(EXT)
Piezo(EXT)
JP14
SPP_SEL
JP31
Dynamic
Dynamic
Dynamic(EXT)
Piezo(EXT)
∗ AKM assumes no responsibility for the trouble when using the above circuit examples.
<KM079406>
2007/04
- 14 -
ASAHI KASEI
[AKD4633-A]
2. Control Software Manual
„ Set-up of evaluation board and control software
1. Set up the AKD4633-A according to previous term.
2. Connect IBM-AT compatible PC with AKD4633-A by 10-line type flat cable (packed with AKD4633-A). Take care
of the direction of 10pin header. (Please install the driver in the CD-ROM when this control software is used on
Windows 2000/XP. Please refer “Installation Manual of Control Software Driver by AKM device control software”.
In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows
NT.)
3. Insert the CD-ROM labeled “AK4633VN Evaluation Kit” into the CD-ROM drive.
4. Access the CD-ROM drive and double-click the icon of “akd4633.exe” to set up the control program.
5. Then please evaluate according to the follows.
„ Operation flow
Keep the following flow.
1. Set up the control program according to explanation above.
2. Click “Port Reset” button.
„ Explanation of each buttons
1. [Port Reset] :
2. [Write default] :
3. [All Write] :
4. [Function1] :
5. [Function2] :
6. [Function3] :
7. [Function4] :
8. [Function5]:
9. [SAVE] :
10. [OPEN] :
11. [Write] :
Set up the USB interface board (AKDUSBIF-A) .
Initialize the register of AK4633VN.
Write all registers that is currently displayed.
Dialog to write data by keyboard operation.
Dialog to write data by keyboard operation.
The sequence of register setting can be set and executed.
The sequence that is created on [Function3] can be assigned to buttons and executed.
The register setting that is created by [SAVE] function on main window can be assigned to
buttons and executed.
Save the current register setting.
Write the saved values to all register.
Dialog to write data by mouse operation.
„ Indication of data
Input data is indicated on the register map. Red letter indicates “H” or “1” and blue one indicates “L” or “0”. Blank is the
part that is not defined in the datasheet.
<KM079406>
2007/04
- 15 -
ASAHI KASEI
[AKD4633-A]
„ Explanation of each dialog
1. [Write Dialog]: Dialog to write data by mouse operation
There are dialogs corresponding to each register.
Click the [Write] button corresponding to each register to set up the dialog. If you check the check box, data
becomes “H” or “1”. If not, “L” or “0”.
If you want to write the input data to AK4633VN, click [OK] button. If not, click [Cancel] button.
2. [Function1 Dialog] : Dialog to write data by keyboard operation
Address Box:
Data Box:
Input registers address in 2 figures of hexadecimal.
Input registers data in 2 figures of hexadecimal.
If you want to write the input data to AK4633VN, click [OK] button. If not, click [Cancel] button.
3. [Function2 Dialog] : Dialog to evaluate IVOL and DVOL
Address Box:
Input registers address in 2 figures of hexadecimal.
Start Data Box:
Input starts data in 2 figures of hexadecimal.
End Data Box:
Input end data in 2 figures of hexadecimal.
Interval Box:
Data is written to AK4633VN by this interval.
Step Box:
Data changes by this step.
Mode Select Box:
If you check this check box, data reaches end data, and returns to start data.
[Example] Start Data = 00, End Data = 09
Data flow: 00 01 02 03 04 05 06 07 08 09 09 08 07 06 05 04 03 02 01 00
If you do not check this check box, data reaches end data, but does not return to start data.
[Example] Start Data = 00, End Data = 09
Data flow: 00 01 02 03 04 05 06 07 08 09
If you want to write the input data to AK4633VN, click [OK] button. If not, click [Cancel] button.
<KM079406>
2007/04
- 16 -
ASAHI KASEI
[AKD4633-A]
4. [Save] and [Open]
4-1. [Save]
Save the current register setting data. The extension of file name is “akr”.
(Operation flow)
(1) Click [Save] Button.
(2) Set the file name and push [Save] Button. The extension of file name is “akr”.
4-2. [Open]
The register setting data saved by [Save] is written to AK4633VN. The file type is the same as [Save].
(Operation flow)
(1) Click [Open] Button.
(2) Select the file (*.akr) and Click [Open] Button.
<KM079406>
2007/04
- 17 -
ASAHI KASEI
[AKD4633-A]
5. [Function3 Dialog]
The sequence of register setting can be set and executed.
(1) Click [F3] Button.
(2) Set the control sequence.
Set the address, Data and Interval time. Set “-1” to the address of the step where the sequence should be paused.
(3) Click [Start] button. Then this sequence is executed.
The sequence is paused at the step of Interval="-1". Click [START] button, the sequence restarts from the paused step.
This sequence can be saved and opened by [Save] and [Open] button on the Function3 window. The extension of file
name is “aks”.
Figure 1. Window of [F3]
<KM079406>
2007/04
- 18 -
ASAHI KASEI
[AKD4633-A]
6. [Function4 Dialog]
The sequence that is created on [Function3] can be assigned to buttons and executed. When [F4] button is clicked, the
window as shown in Figure 2 opens.
Figure 2. [F4] window
<KM079406>
2007/04
- 19 -
ASAHI KASEI
[AKD4633-A]
6-1. [OPEN] buttons on left side and [START] buttons
(1) Click [OPEN] button and select the sequence file (*.aks).
The sequence file name is displayed as shown in Figure 3.
Figure 3. [F4] window(2)
(2) Click [START] button, then the sequence is executed.
3-2. [SAVE] and [OPEN] buttons on right side
[SAVE] : The sequence file names can assign be saved. The file name is *.ak4.
[OPEN] : The sequence file names assign that are saved in *.ak4 are loaded.
3-3. Note
(1) This function doesn't support the pause function of sequence function.
(2) All files need to be in same folder used by [SAVE] and [OPEN] function on right side.
(3) When the sequence is changed in [Function3], the file should be loaded again in order to reflect the change.
<KM079406>
2007/04
- 20 -
ASAHI KASEI
[AKD4633-A]
7. [Function5 Dialog]
The register setting that is created by [SAVE] function on main window can be assigned to buttons and executed. When
[F5] button is clicked, the following window as shown in Figure 4 opens.
Figure 4. [F5] window
7-1. [OPEN] buttons on left side and [WRITE] button
(1) Click [OPEN] button and select the register setting file (*.akr).
The register setting file name is displayed as shown in Figure 5.
(2) Click [WRITE] button, then the register setting is executed.
<KM079406>
2007/04
- 21 -
ASAHI KASEI
[AKD4633-A]
Figure 5. [F5] windows(2)
7-2. [SAVE] and [OPEN] buttons on right side
[SAVE] : The register setting file names assign can be saved. The file name is *.ak5.
[OPEN] : The register setting file names assign that are saved in *.ak5 are loaded.
7-3. Note
(1) All files need to be in same folder used by [SAVE] and [OPEN] function on right side.
(2) When the register setting is changed by [Save] Button in main window, the file should be loaded again in order to
reflect the change.
<KM079406>
2007/04
- 22 -
ASAHI KASEI
[AKD4633-A]
8. [Filter Dialog]
It is possible to calculate the coefficients of HPF and EQ filters, write these coefficients to registers and confirm the
frequency response of these filters. Click [Filter] button, then the window as shown in Figure 6 opens.
Figure 6. [Filter] Window
(1) Setup the Parameters
Set up the parameters of HPF and EQ filters.
Parameter
Contents
Sampling Rate
Sampling Frequency (fs)
HPF Cut Off Frequency
High Pass Filter Cut Off Frequency
EQ1 Center Frequency
EQ1 Center Frequency
EQ1 Band Width
EQ1 Band Width
(Note 1)
EQ1 Gain
EQ1 Gain
(Note 2)
EQ2 Center Frequency
EQ2 Center Frequency
EQ2 Band Width
EQ2 Band Width
(Note 1)
EQ2 Gain
EQ2 Gain
(Note 2)
Note 1. Band width of 3dB gain difference from center frequency
Note 2. This filter is notch filter when this gain is -1.
Setup range
48000Hz ≥ fs ≥ 7350Hz
(fs/2 – 1) ≥ fc > fs/10000
fs/2 ≥ EQ1 > 0Hz
fs/2 ≥ EQ1 >1Hz
3 > EQ1 ≥- 1
fs/2 ≥ EQ2 > 0Hz
fs/2 ≥ EQ2 >1Hz
3 > EQ2 ≥- 1
(2) Filter ON/OFF
Set up the ON or OFF of filters by the check button of "HPFAD", "HPF", "EQ1" and "EQ2". The filter is ON when the
button is checked.
Figure 7. Filter ON/OFF check button
<KM079406>
2007/04
- 23 -
ASAHI KASEI
[AKD4633-A]
(3) Calculation of Register Setting
When [Register Setting] is clicked, the register setting of filters are displayed in "Register Setting" area. At the same this,
these setting are written to HPFAD bit, HPF bit, EQ1 bit, EQ2 bit and 10H-1FH registers. If the parameter is out of range,
then the error message is displayed and these writing to register aren't executed.
Figure 8. Calculation result to register parameters
(4) Frequency Response
When [Register Setting] is clicked, the frequency response is displayed. At the same this, these setting are written to
HPFAD bit, HPF bit, EQ1 bit, EQ2 bit and 10H-1FH registers. If [UpDate] button is clicked after setting the frequency
range, the display of frequency response is updated.
Figure 9. Frequency characteristic indicates result
<KM079406>
2007/04
- 24 -
ASAHI KASEI
[AKD4633-A]
Revision History
Date
05/07/14
05/08/23
05/09/16
05/10/21
06/04/14
Manual
Revision
KM079400
KM079401
KM079402
KM079403
KM079404
Board
Revision
0
1
1
2
2
Reason
First Edition
Update
Error Correct
Update
Update
07/02/15
KM079405
3
Error Correct
07/04/02
KM079406
3
Error Correct
Contents
Change of a figure & circuit
Port Numbers are corrected in circuit.
Device revision of AK4633 is changed to “Rev.B”.
Part change in LOGIC circuit diagram.
U9: 74LVC541Æ74HC541
Port number was corrected in both silkscreen printing and
circuit diagram. JP1(MICP) Æ JP2 (MICP)
Port number was corrected in both silkscreen printing and
circuit diagram.
Silkscreen printing: JP2 (MCKI) Æ JP6 (MCKI)
Circuit diagram: JP5 (MCKI) Æ JP6 (MCKI)
IMPORTANT NOTICE
• These products and their specifications are subject to change without notice. Before considering
any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or
authorized distributor concerning their current status.
• AKM assumes no liability for infringement of any patent, intellectual property, or other right in the
application or use of any information contained herein.
• Any export of these products, or devices or systems containing them, may require an export license
or other official approval under the law and regulations of the country of export pertaining to customs
and tariffs, currency exchange, or strategic materials.
• AKM products are neither intended nor authorized for use as critical components in any safety, life
support, or other hazard related device or system, and AKM assumes no responsibility relating to
any such use, except with the express written consent of the Representative Director of AKM. As
used here:
(a) A hazard related device or system is one designed or intended for life support or maintenance of
safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its
failure to function or perform may reasonably be expected to result in loss of life or in significant
injury or damage to person or property.
(b) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or
system containing it, and which must therefore meet very high standards of performance and
reliability.
• It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or
otherwise places the product with a third party to notify that party in advance of the above content
and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability
for and hold AKM harmless from any and all claims arising from the use of said product in the
absence of such notification.
<KM079406>
2007/04
- 25 -
D
AVSS
SVSS
VCC3.3V
REG
AVDD
DVDD
AVSS
SVDD
SVSS
DGND
T45_O
T45_R
T45_O
T45_O
T45_BK
T45_BU
T45_BK
T45_BK
REG_IN
AVDD
DVDD
AVSS
SVDD
1
1
1
1
1
1
1
1
25
26
27
28
VCC3.3V
AVSS
SVSS
JP2
MICP
R1
2.2k
+
C1
1u
E
E
CN1
32pin_4
29
AVSS
30
C3
+
47u
31
1
2
C2
0.1u
32
GND
REG
OUT
C1
0.1u
E
INT
JP1
GND
REG_IN T1
TA48033F
IN
C
AOUT
B
BEEP
A
BEEP
MICP
TP4
BEEP
C2
0.22u
TP2
AOUT
1
1
1
C3
10u
D
AVSS
C5
0.1u
REG
10k
TP14
VCOC
VCOM
2
AVSS
3
AVDD
R4
(open)
SPN
JP4 REG
SVDD_SEL
DVSS
14
C10
0.1u
13
BICK
FCK
SDTO
CDTI
SPN
20
SPP
19
4633_MCKO
18
4633_MCKI
2
(short)
TP10 MCKO
1
MCKI
PDN
DVDD
21
C16
+
47u
TP12 MCKI
VCOC
CSN
SVDD
L2
SVSS
JP6 MCKI
C11
10u
17
C
32pin_3
AVSS
32pin_1
12
51
11
R7
9
7
8
10
1
PDN
17
16
5
TP15
PDN
AVSS
SPP
MCKO
15
CCLK
7
D
SVDD 1
TP9
SPP
18
4
6
C
AK4633VN
SDTI
1
C9
4.7n
6
22
1
4
5
23
TP13
SPN
1
19
20
21
22
1
R5
1
8
AVSS
AVSS
TP6
SVDD
1
C8
0.1u
SVSS
C7
10u
SVDD
TP8
AVSS AVDD
BEEP
3
AVDD
AOUT
AVDD
MPI
1
(short)
23
U1
1
1
+
2
47u
C4
0.1u
+
C13
2
2
+
24
L1
1
C6
2.2u
TP7
AVSS
MIC
REG
+
AVDD_IN
AVSS
TP11
VCOM
1
REG
24
1
CN2
JP3
AVDD_SEL
CN3
+
R2
2.2k
1
1
2
TP1
TP3
MIC MPI
B
B
AVDD
JP9
AVDD DVDD_SEL
DVDD_IN
L4
C22
+
TP17 TP18
CCLK CDTI
1
DVDD
DVDD
R40
(short)
TP19
SDTI
1
TP20 TP21
SDTO FCK
1
1
TP22
BICK
1
TP23
DVDD
1
1
R14 10
2
(short)
1
DVDD
R8
51
JP10
LVC_SEL
R9
51
R10
51
R11
51
R12
51
R13
51
R22
51
2
47u
1
1
TP16
CSN
L5
16
15
14
13
A
A
B
C
Title
DVDD
4633_BICK
CDTI
CCLK
4633_FCK
VCC
4633_SDTO
1
2
(short)
CSN
47u
+
2
C23
CN4
32pin_2
D3.3V
4633_SDTI
1
A
JP11
VCC_SEL
12
LVC
11
VCC3.3V
10
VCC
9
LVC
AVSS
Size
A3
Date:
D
AKD4633-A
Document Number
Rev
AK4633-VN
Friday, March 30, 2007
Sheet
E
3
1
of
5
A
B
C
D
E
J1
MIC-JACK
6
JP31
Dynamic
4
3
E
AVSS
JACK
JP12
MIC_SEL
R15
10
INT
J3
MIC
RCA
6
JP13
D1
A
K
MR-552LS
AVSS
SVSS
C26
1u
2
R18
47k
MR-552LS
R19
1
+
2
3
1
A
BEEP
20k
SVSS
Dynamic(EXT)
Piezo(EXT)
Dynamic
SPK1
SPN_SEL
DIODE ZENER
JP14
D2
J4
BEEP
AVSS
E
3
4
SPN
2
3
1
D
J2
SPK-JACK
SVSS
K
DIODE ZENER
020S16
CN5
Dynamic(EXT)
Piezo(EXT)
Dynamic
R
2
SPP_SEL
1
L
R17
10
AVSS
D
SPP
+
C28
1
AOUT
R20
220
J5
AOUT
2
2
3
1
1u
R21
20k
MR-552LS
AVSS
AVSS
C
C
B
B
A
A
Title
Size
A3
Date:
A
B
C
D
AKD4633-A
Document Number
Rev
Input/Output
Thursday, February 15, 2007
Sheet
E
3
2
of
5
A
B
C
D
E
for
74HCU04,74AC74,74VHC4040,74HC14,74HC14,74LVC541,74HCT04
1
C30
0.1u
C31
0.1u
C32
0.1u
C33
0.1u
C34
0.1u
C35
0.1u
C36
0.1u
2
2
E
1
D3.3V
12.288MHz
X1
E
+ C37
47u
R24
1M
U2C
5
U2B
6
3
74HCU04
JP17
XTE
C38
(open)
4
74HCU04
C39
(open)
D
D
EXT_MCLK
Q
10
5
12
D
11
CLK
PR
Q
CL
CLK
CL
MCLK_SEL
C
3
U4A
74AC74
6
1
DIR_MCLK
R25
short
D
D3.3V
U4B
74AC74
Q
Q
9
256fs
512fs
1024fs
MCKO
JP18
MKFS
U3
10
11
8
13
JP21
XTL
DIR
EXT
2
PR
4
D3.3V
CLK
RST
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q11
Q12
9
7
6
5
3
2
4
13
12
14
15
1
74VHC4040
JP19
BICK_SEL
64fs
32fs
16fs
EXT
THR
1
JP20
BICK
EXT_BICK
2
U5A
74HC14
INV
C
JP22
2fs
1fs
EXT
EXT_FCK
FCK_SEL
MCKO
J8
EXT/BICK
2
3
1
B
B
R26
51
MR-552LS
AVSS
JP23
EXT1
J9
FCK
2
3
1
R27
51
MR-552LS
AVSS
A
JP24
EXT2
A
Title
Size
A3
Date:
A
B
C
D
AKD4633-A
Document Number
Rev
CLOCK
Thursday, February 15, 2007
Sheet
E
3
3
of
5
A
B
C
D
E
C40 C41
0.1u 0.1u
D3.3V
L6
(short)
R28
10k
3
2
1
VCC
GND
OUT
0.1u
C43
10u
R29
470
2
4
1
E
U5C
3
74HC14
D3.3V
+
TORX141
U5B
D3
HSU119
6
5
74HC14
L
C44
0.1u
H
SW1
DIR
2
C45
0.1u
1
C42
3
PORT1
A
2
E
K
1
D3.3V
1
38
37
INT1
R
AVDD
40
39
R30
18k
VCOM
41
AVSS
42
RX0
43
NC
44
RX1
45
TEST1
46
RX2
U6
16
15
14
13
12
11
10
9
NC
48
SW3
1
2
3
4
5
6
7
8
RX3
DIF0
DIF1
DIF2
CM0
CM1
OCKS0
OCKS1
M/S
D
47
C46
0.47u
D
R31
1k
U7D
IPS0
INT0
36
9
8
LED1
ERF
K
A
D3.3V
74HC04
2
NC
OCKS0
35
OCKS0
3
DIF0
OCKS1
34
OCKS1
4
TEST2
CM1
33
CM1
5
DIF1
CM0
32
CM0
6
NC
PDN
31
7
DIF2
XTI
30
8
IPS1
XTO
29
9
P/SN
DAUX
28
10
XTL0
MCKO2
27
11
XTL1
BICK
26
DIR_BICK
12
VIN
SDTO
25
DIR_SDTI
RP1
CM0
CM1
OCKS0
OCKS1
M/S
47k
AK4114
C
C
C47
(open)
1
9
8
7
6
5
4
3
2
1
C48
(open)
2
X2
11.2896MHz
DAUX
2
1
C51
10u
D3.3V
LRCK
24
MCKO1
23
22
C50
0.1u
+
+
C49
0.1u
1
DVSS
DVDD
21
20
VOUT
UOUT
19
COUT
18
BOUT
17
TX1
16
15
14
TVDD
13
TX0
B
DVSS
B
DIR_FCK
JP25
MCKO_SEL
MCKO2
MCKO1
DIR_MCLK
2
C52
10u
D3.3V
PORT2
A
IN
VCC
GND
3
2
1
A
D3.3V
C53
0.1u
TOTX141
Title
Size
A3
Date:
A
B
C
D
AKD4633-A
Document Number
Rev
DIR/DIT
Thursday, February 15, 2007
Sheet
E
3
4
of
5
A
B
C
D
U8
74HC541
1
E
11
Y8
A8
9
12
Y7
A7
8
4633_MCKO
4633_MCKI
13
Y6
A6
7
EXT_MCLK
DAUX
14
Y5
A5
6
4633_SDTO
JP26
4633_SDTI DAC/LOOP
4633_SDTI
15
Y4
A4
5
16
Y3
A3
4
17
Y2
A2
3
18
Y1
A1
2
MCKO
E
LVC
DIR
20
VCC
E
M/S
C54
0.1u
GND
10
A1
B1
18
3
A2
B2
17
4
A3
B3
16
5
A4
B4
15
6
A5
B5
14
7
A6
B6
13
B7
12
19
G
2
RP2
RP3
7
6
5
4
3
2
1
47k
ADC
7
6
5
4
3
2
1
47k
D
D
10
GND
4633_BICK
19
G2
VCC
A7
JP27
BICK
ADC
DIR
C55
0.1u
20
8
4633_FCK
1
G1
9
A8
EXT_BICK
DIR_BICK
11
B8
JP28
FCK
74LVC245
ADC
DIR
U9
EXT_FCK
DIR_FCK
C
C
2
1
LVC
JP29
U10F
+ C56
47u
13
INV
12
THR
74HC14
BICK_INV
R32
R34
R36
D3.3V
PORT4
1
2
3
4
5
B
10
9
8
7
6
10k
10k
10k
R33
R35
R37
U11
470
470
470
CSN
CCLK
CDTI
2
3
4
5
6
7
8
9
A1
A2
A3
A4
A5
A6
A7
A8
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
18
17
16
15
14
13
12
11
1
19
G1
G2
VCC
GND
20
10
CSN
CCLK
CDTI
PDN
4633_MCKI
MCLK
BICK
FCK
SDTI
VCC
10
9
8
7
6
ROM
D3.3V
B
R38
74LVC541
CTRL
PORT3
1
2
3
4
5
D3.3V
10k
ADC
K
D3.3V
A
D4
HSU119
R39
10k
U5D
9
11
10
U2A
74HC14
1
1
C57
0.1u
13
10
74HCU04
5
3
11
U10C
10
5
74HC04
74HC04
13
6
U10E
11
74HC14
U7F
6
4
74HC14
U7E
4
U7C
U2E
U10B
2
74HC04
74HC04
74HCU04
11
1
U7B
3
2
8
12
74HCU04
U2D
9
U7A
U2F
2
74HCU04
SW2
PDN
A
U10D
12
74HC04
9
8
74HC14
10
A
74HC14
U10A
1
Title
2
74HC14
Size
A3
Date:
A
DIR_SDTI
DIR
U5E
8
74HC14
H
3
L
DAUX
JP30
SDTI
B
C
D
AKD4633-A
Document Number
Rev
LOGIC
Thursday, February 15, 2007
3
Sheet
E
5
of
5