32-Bit Microcontroller TriBoard TC176X/TC116X/TC1782/ TC1387 Hardware: TriBoard-LQFP176 V2.1 Hardware Manual User’s Manual V 2.1 2009-06 Microcontrollers Edition 2009-06 Published by Infineon Technologies AG 81726 Munich, Germany © 2009 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 32-Bit Microcontroller TriBoard TC176X/TC116X/TC1782/ TC1387 User’s Manual V 2.1 2009-06 Microcontrollers TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard TC176X/TC116X/TC1782/TC1387 User’s Manual Revision History: V 2.1 2009-06 Previous Versions: TriBoardManual-TC176X-TC116X-TC1782-TC1387 V2.0 Page Subjects (major changes since last revision) – change to actual manual template – add support for 1,3V VDD incl. updated schematic Trademarks TriCore® is a trademark of Infineon Technologies AG. We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] User’s Manual V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 2 2.1 2.2 2.3 TriBoard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2-1 2-3 2-4 3 3.1 3.2 3.3 3.4 3.4.1 3.4.2 3.5 3.5.1 3.6 3.7 3.8 3.9 3.10 3.11 3.11.1 3.11.2 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MiniWiggler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FlexRay / IFlex (optional if not with TC1767, TC1782 or TC1387) . . . . . FlexRay as option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety option with SAK-CIC61508 (optional if not with TC1387) . . . . . . . Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3-1 3-1 3-1 3-2 3-2 3-2 3-3 3-3 3-3 3-3 3-4 3-4 3-4 3-4 3-4 3-5 4 4.1 4.2 4.3 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HW Boot Configuration TC1767, TC1782 and TC1387 . . . . . . . . . . . . . . HW Boot Configuration all other TC176X / TC116X . . . . . . . . . . . . . . . . Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4-1 4-2 4-4 5 5.1 5.2 5.3 TriBoard Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 5-1 5-1 5-1 6 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 7 7.1 7.2 7.3 7.4 7.5 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TC176X/TC116X Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flexray Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User’s Manual L-1 7-1 7-2 7-4 7-4 7-4 7-5 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual 7.6 7.7 OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 DAP connector pinout (only with TC1767, TC1782, TC1387) . . . . . . . . . 7-5 8 8.1 8.1.1 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 New and changes on schematic version V2.1 to TriBoard TC176X/TC116X/TC1782/TC1387 V2.0 8-1 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 8.2 8.3 User’s Manual L-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual List of Figures Figure 2-1 Figure 2-2 Figure 3-1 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 7-1 Figure 7-2 Figure 7-3 Figure 7-4 Figure 7-5 Figure 7-6 Figure 7-7 Figure 7-8 Figure 8-1 Figure 8-2 Figure 8-3 Figure 8-4 Figure 8-5 Figure 8-6 Figure 8-7 Figure 8-8 Figure 8-9 Figure 8-10 Figure 8-11 Figure 8-12 User’s Manual TriBoard Block Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 TriBoard LQFP176 V2.1 Placement . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Clock socket usage (XT301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 HW Configuration TC1767, TC1782, TC1387 DIP-Switch. . . . . . . . . 4-1 HW Configuration for all other TC176X / TC116X DIP-Switch. . . . . . 4-2 Location of general optional resistors on Top Side . . . . . . . . . . . . . . 4-5 Location of general optional resistors on Bottom Side. . . . . . . . . . . . 4-5 Location of peripheral resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-7 Location of peripheral resistors on Bottom Side . . . . . . . . . . . . . . . . 4-7 Location of resistors for safety device on Bottom Side . . . . . . . . . . . 4-8 Connector for TC176X/TC116X/TC1782/TC1387 - Pinout (Part I, Top View) 7-2 Connector for TC176X/TC116X/TC1782/TC1387 - Pinout (Part II, Top View) 7-3 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Flexray Pinout (SUBD-9 Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 DAP connector pinout (FTSH10) - only with TC1767, TC1782, TC1387. . 7-5 Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Schematic - Config, Clock and CIC61508 . . . . . . . . . . . . . . . . . . . . . 8-3 Schematic - IFlex, CAN and Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Schematic - MiniWiggler, DAP and ETK . . . . . . . . . . . . . . . . . . . . . . 8-5 Schematic - GPTA, MSC, MLI and ADC . . . . . . . . . . . . . . . . . . . . . . 8-6 Schematic - Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Schematic - Connectors (Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Schematic - Connectors (Socket) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Component Plot Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 L-3 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual User’s Manual L-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual List of Tables Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 6-1 Table 6-2 Table 6-3 Table 6-4 Table 6-5 Table 6-6 Table 6-7 User’s Manual User Startup Modes for TC1767, TC1782 and TC1387 . . . . . . . . . . HW Boot Configuration for all other TC176X / TC116X . . . . . . . . . . . General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for safety device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety device Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L-5 4-1 4-2 4-4 4-6 4-8 6-1 6-1 6-2 6-2 6-2 6-2 6-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual User’s Manual L-6 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual User’s Manual -7 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Introduction 1 Introduction We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quick access to the capabilities of TriCore's powerful architecture. Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features (OCDS1 and DAP). The kit also includes several sets of development tools, which are stored on the included Evaluation Board CD-ROM. The Evaluation Board allows easily the development of TriCore applications with the corresponding tools. Subsequently, the applications can be downloaded and can be tested with the powerful debugger software. This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the initial configuration of the TriBoard. For detailed technical information about the TC176X / TC116X / TC1782 / TC1387 please refer to the User Manual of the corresponding device. User’s Manual 1-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Introduction User’s Manual 1-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Features 2 TriBoard Features The TriBoard TC176X/TC116X/TC1782/TC1387 is soldered with a device of the TC176X or TC116X or TC1782 or TC1387. This devices fits into all members of this product family so that there are no special TriBoards necessary. 2.1 – – – – – – – – – – – Summary of Features Infineon’s TC176X, TC116X, TC1782 or TC1387 Controller in LQFP176 Package FlexRay Transceivers (optional if not with TC1767 or TC1782 or TC1387) Safety device (optional if not with TC1387) High Speed CAN Transceivers USB to UART bridge Crystal 20MHz (default), Oscillator or External Clock USB miniWiggler for easy debugging 8 Low Power Status LEDs 8-DIP switches for configuration access to all pins of controller 100mm x 160mm (EURO-Board) Connectors The TC176X / TC116X / TC1782 / TC1387 TriBoard offers a wide variety of connectors: – – – – – – Standard power connector USB connector for ASC Interface (ASC0) and miniWiggler 16-pin header for JTAG interface (OCDS) 10-pin header for DAP (only TC1767, TC1782, TC1387) 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1) 2 x SUB-D9 Plug connector for FlexRay (optional if not with TC1767, TC1782, TC1387) – four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals – optional ETK connector Components – – – – – – Infineon’s Next generation micro controller supply TLE 7368 G Three LEDs to validate power supply (5Volt / 3,3 Volt / VCORE) LED indicating /HDRST (ESR0) active state LED indicating activ miniWiggler LED switched via DAS software Infineon’s FlexRay Communication Controller SAK-CIC310 (optional if not with TC1767, TC1782, TC1387) – 2x FlexRay Transceiver AS8221(AMS) or TJA1080 (NXP) (optional if not with TC1767, TC1782, TC1387) – 2 x Infineon’s High Speed CAN-Transceiver TLE 6250 GV33 – Infineon’s Safety Device SAK-CIC61508(optional if not with TC1387) User’s Manual 2-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Features – – – – – USB to UART bridge FT2232D (FTDI) SPI eeprom (Atmel) 8 general purpose LEDs Reset switch 8-pin Dip switch Zero Ohm Bridges Zero Ohm resistors give the flexibility to configure the systems functionality User’s Manual 2-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Features 2.2 Block Diagram XTAL CAN0 RxCAN0 CAN1 PLL TxCAN0 Transceiver TxCAN1 RxCAN1 TC176X / TC116X / TC1782 / TC1387 OCDS1 miniWiggler ERAY A FlexRay only with TC1767, TC1782 and TC1387 for other devices optional ERAY B FlexRay Transceiver Figure 2-1 User’s Manual MLI0 RXD0 8 LED’s (P5.0 up to P5.7) SAKCIC310 SLSO00 TriCore CPU TXD0 SSC0 USB SSC1 USB B-TYPE Serial EEPROM Safety Device SAK-CIC61508 optional if not with TC1387 POWER SUPPLY WITH SUPERSONIC TLE7368G / TLE7368-2G TriBoard Block Schematic 2-3 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Features 2.3 Placement USB P401 RUN 1 X202 1 2 3 4 5 6 7 8 XT201 S201 1 DAP VDDP_CIC 1 OCDS1 R249 X402 SYSDISC BOOTCONFIG ACT SYSDISB X403 A1 1 X203 OCDS1_CIC P5.0 P5.1 P5.2 P5.3 P5.4 P5.5 P5.6 P5.7 ETK ERAY-A X701 1 1 SYSDISA X704 1 1 SEND Figure 2-2 User’s Manual R245 U601 JP201 R242 SENC R237 1 SENB RST_CIC SENA S202 RESET_CIC X703 +5,5V...+50V(+40V) X201 TC176X/TC116X/ TC1782/TC1387 +VDD JP202 SAK-CIC61508 JP203 +3V3 1 +5V U202 1 X302 RST X601 SUPERSONIC S601 CAN1 P302 U201 1 RESET POWER TriBoard-LQFP176 V2.1 ERAY-B X301 X401 1 CAN0 L1 1 P301 CLOCK X702 1 1 1 1 TriBoard LQFP176 V2.1 Placement 2-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Information 3 TriBoard Information 3.1 Power Supply The Board has to be connected to a +5,5V to +50V (+40V) DC power supply. The TriBoard generates internally +3.3V, +VDD and +5V. The power consumption is not specified yet but a supply with 6V and 500mA should be sufficient. The pinout for the supply connector is shown in Figure 7-3. There can be used any standard power pack with a connector where the positive line is surrounded by the ground line. Maximum power supply is reduced to +40V if the SAK-CIC61508 option is assembled (always with TC1387). +VDD is +1,3V for TC1782, for all other devices +1,5V. NOTE: on first TC1782 device +VDD is +1,2V. Applying a stable supply voltage causes the power on reset after a short period. The four LED's (+5V, +3.3V, +VDD) indicate the status of the on board generated voltage (if the LEDs are assembled). A manual reset is executed by pressing the reset button. 3.2 LEDs There are 14 or 19 LEDs on board: – – – – – – – – – – – – 3.3 D501 up to D508 (blue) D604 RST (red) D505 +VDD (green) D606 +3V3 (green) D607 +5V (green) D402 ACT (green) D401 RUN (red) D204 RST_CIC (red) D205 +VDDP_CIC (green) D201 SYSDISA (red) D202 SYSDISB (red) D203 SYSDISC (red) -> toogle LEDs connected to P5.0 ... P5.7 -> RESET LED indicate the reset state of the board -> +VDD power supply indication (+1.3V/+1.5V) -> +3,3V power supply indication -> +5V power supply indication -> on board MiniWiggler is ACTIV -> Debug RUN mode (switched by DAS Server) -> RESET LED indicate that the CIC is in reset -> +VDDP for CIC power supply indication (+3,3V) -> System Disable A (switched by CIC) -> System Disable B (switched by CIC) -> System Disable C (switched by CIC) Clock There are three possibilities to apply the CPU clock. • • • • Large oscillator circuit (DIP14) Small oscillator circuit (DIP8) Crystal oscillator (default with 20MHz) External clock generator User’s Manual 3-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Information The crystal oscillator and the oscillator circuit use the socket XT301. It's possible to apply a 14pol DIP oscillator package or an 8pol DIP oscillator package. OSCILLATOR OSCILLATOR XTAL DIP14 DIP8 Figure 3-1 3.4 GND External Clock Input Clock socket usage (XT301) USB Connector The USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASC0 as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 7-4. NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. For actual DAS software please contact your local FAE. The software can also be found on the DAS website 3.4.1 Serial Connection to PC After the first connection of USB to a PC the needed driver will be installed automatically. During this there will be created a new COM port on PC. This COM port can be used to communicate with the board via ASC0 of the device (e.g. bootstrap loader). 3.4.2 MiniWiggler MiniWiggler is a low cost debug tool which allows you access to the JTAG of the device. Make sure that you have the latest DAS release. Debugging is possible via the DAS Server JTAG over USB Chip. Please contact your prefered debug vendor for support of DAS. If you have connected the board to the PC and there runs the DAS server, then a working connection is visible via the green ACTIV LED. The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client). User’s Manual 3-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Information IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if the ACTIV LED is on. 3.5 FlexRay / IFlex (optional if not with TC1767, TC1782 or TC1387) The FlexRay devices are only assembled if the board is with TC1767, TC1782, TC1387 or with the FlexRay option. The board has 2 SUB-D connectors for FlexRay Communication with up to 10 Mbit/s. For the pinout of the plugs see Figure 7-5. The transceiver are connected to the FlexRay Communication Controller SAK-CIC310 (IFlex). Normally the SAK-CIC310 is connected to MLI0 of the TriCore Controller but the IFlex can also be connected to SSC1.For using the IFlex with SSC see Table 4-4. As interrupts inputs of TC176X/TC116X are used P0.7, P0.11, P3.10 and P3.11 and in case of SSC1 connection you can also use P0.6. For more information look in the user manual for TC176X/TC116X or SAK-CIC310 and the schematics Figure 8-4. 3.5.1 FlexRay as option If the board comes without FlexRay (e.g. with TC1766) then you can add the FlexRay option by assembling the following parts: • • • • U301 with SAK-CIC310 (Infineon) U302 and U303 with AS8221 (AMS) or TJA1080 (NXP) (if with TJA1080 then resistors R366-R371 and capacitor CB312 and CB316 must be assembled with 0R and 100n, package 0603) Y301 with 20MHz crystal (5x3mm SMD, e.g. NDK NX5032GA) T301 and T302 with B82790-S513-N (Epcos) 3.6 Serial Eeprom The SSC0 of the TC176X / TC116X / TC1782 / TC1387 is connected to a serial EEPROM with a size of 128K (16.384 x 8). As chip select for this EEPROM is used the line SLSO00 (P3.5). To disconnect (disable) the EEPROM remove resistor R353. 3.7 MultiCAN On the board are two CAN transceiver connected to the MultiCAN on TC176X / TC116X / TC1782 / TC1387 node 0 and 1. The transceivers are connected to two IDC10 plug. For the pinout of IDC10 plug see Figure 7-6. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9. User’s Manual 3-3 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Information 3.8 Safety option with SAK-CIC61508 (optional if not with TC1387) The safety device is only assembled if the board is with TC1387 or with the safety option. The SAK-CIC61508 is connected to the SSC0 of the microcontroller and use the line SLSO01 (P3.6) as chip select. There are 4 LED’s for indication the state of the safety device (SYSDISA, SYSDISB, SYSDISC, VDDP_CIC). On this board exists 4 potentiometer to stimulare the sense inputs of the safety device. Sensor inputs A and B can be connect to a potentiometer (JP201, JP202 , pos. 2-3) or to the core voltage of the microcontroller (JP201, pos. 1-2) for input A or to the port voltage of the microcontroller (JP202, pos. 1-2) for input B. With switch S202 it is possible to reset the safety device. If JP203 is set, then with S202 is also reset the microcontroller and the safety device is reset by a power on reset of the microcontroller. The safety device can be reprogrammed via JTAG and X203. 3.9 Other peripherals For all other peripherals there are no special plugs on the board. The peripheral signals are available on the different connectors. See “Connector Pin Assignment” on Page 7-1. Note: - SLSO00 is used as chip select for the serial eeprom on board. 3.10 Toggle LED’s Port 5 pin 0 up to pin 7 are connected to single LED’s (D501... D508) and can be controlled by Software. This status LED’s are low active. 3.11 Debug System 3.11.1 OCDS1 The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of +3.3V. For pinout of the connector see Figure 7-7. You can connect any debugger to this connector. The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector then assemble R425 and R424 with a 0R resistor. If you connect a debug hardware make sure that the MiniWiggler (see “MiniWiggler” on Page 3-2) is not activ (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is tristated. User’s Manual 3-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Information If the ACTIV LED is on, then stop the active DAS Server JTAG over USB Chip and/or remove the USB connection to the PC. 3.11.2 DAP If the board comes with a TC1767, TC1782 or TC1387 then the DAP connector (X402) is available. For pinout of this connector see Figure 7-8. You can connect a DAP hardware here. If you use this connector make sure that the MiniWiggler is not activ (ACTIV LED is off) and a connected OCDS1 hardware is disconnected or tristated. User’s Manual 3-5 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Information User’s Manual 3-6 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual HW Boot Configuration TC1767, TC1782 and TC1387 Figure 4-1 P0 . P0 .5 .4 P0 P0 .2 P0 .1 P0 0 HIGH 1 P0 . LOW P0 . 4.1 6 TriBoard Configuration .3 4 7 TriBoard Configuration on 2 3 4 5 6 7 8 HW Configuration TC1767, TC1782, TC1387 DIP-Switch The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will be described in the following table (Table 4-1). Note: The ON position of the switch is equal to a logical LOW at the dedicated pin. Table 4-1 User Startup Modes for TC1767, TC1782 and TC1387 Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch numbers HWCFG[7...0] Type of Boot TC1767, TC1782 and TC1387 1 2 3 4 5 6 7 8 11XXXXXX Internal Start from Flash X X X X X X O O F F F F 010XXXX0 Bootstrap Loader Mode, Generic Bootloader at O X X X X O O O CAN pins N N F N F 10101XX0 Bootstrap Loader Mode, ASC Bootloader O X X O O O O O N F N F N F F F F 10100XX0 Alternate Boot Mode, ASC Bootloader on fail O X X O O O O O N N N F N F F F User’s Manual 4-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration Table 4-1 User Startup Modes for TC1767, TC1782 and TC1387 Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch numbers HWCFG[7...0] Type of Boot TC1767, TC1782 and TC1387 1 2 3 4 5 6 7 8 1011XXXX Alternate Boot Mode, Generic Bootloader at CAN pins on fail X X X X O O O O F F N F F F F all others reserved; don’t use this combination HIGH 7 P0 . 6 P0 . P0 .5 P0 .4 P4 .3 P4 .2 LOW P4 .1 HW Boot Configuration all other TC176X / TC116X P4 .0 4.2 on 1 2 Figure 4-2 3 4 5 6 7 8 HW Configuration for all other TC176X / TC116X DIP-Switch The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will be described in the following table (Table 4-2). Note: The ON position of the switch is equal to a logical LOW at the dedicated pin. Table 4-2 HW Boot Configuration for all other TC176X / TC116X Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch number P4[3...0] P0[7...4] Type of Boot TC176X / TC116X 1 2 3 4 5 6 7 8 0000 XXXX Serial boot from ASC to PMI scratchpad via ASC pins, run loaded program O O O O X X X X N N N N 0001 XXXX Serial boot from CAN to PMI scratchpad, run loaded program O O O O X X X X F N N N F User’s Manual 4-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration Table 4-2 HW Boot Configuration for all other TC176X / TC116X Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch number P4[3...0] P0[7...4] Type of Boot TC176X / TC116X 1 2 3 4 5 6 7 8 0010 XXXX Start from internal flash O O O O X X X X N F N N F 0011 XXXX Alternate Boot Mode, Generic Boot Loader on fail depends on P0[2...0] O O O O X X X X F F N N F F 1000 XXXX Boot from emulation memory (ED only) O O O O X X X X N N N F F 1111 XXXX Serial boot from ASC to PMI scratchpad via CAN pins, run loaded program O O O O X X X X F F F F F F F F all others all others reserved; don’t use this combination User’s Manual 4-3 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration 4.3 Assembly Options Table 4-3 General optional resistors Component Description R205 XTAL Rserial (default: assembled) R206 XTAL Rparallel (default: not assembled) R423 Connect /BRKOUT with MiniWiggler (default: not assembled) R424 Connect /BRKOUT with OCDS1 connector (default: not assembled) R427 Connect /BRKIN with USR1 of MiniWiggler (default: not assembled R429 Connect /BRKIN with USR1 of DAP (default: not assembled R425 Connect /BRKIN with OCDS1 connector(default: not assembled) R428 Connect /TESTMODE with USR1 of MiniWiggler (default: not assembled R430 Connect /TESTMODE with USR1 of DAP (default: not assembled R426 Connect /TESTMODE with OCDS1 connector(default: not assembled) R432 Connect debug reset with /PORST(default: assembled) R431 Connect debug reset with /HDRST (default:not assembled) R510 Connect +3,3V to all toggle LEDs (default: assembled) R623 Connect reset switch with /PORST(default: assembled) R624 Connect reset switch with /HDRST (default:not assembled) R604 Connect P1.2 with MONSTBY of power device (default: not assembled) R606 Connect P1.3 with WDO of power device (default: not assembled) R609 Connect P1.15 with WDI of power device (default: not assembled) User’s Manual 4-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration Note: All resistors are red marked in the following figures R407 X704 D205 R249 R245 R242 JP202 U203 X302 CB208 X201 R355 JP203 R228 C603 D606 D605 CB319 R601 R501 R237 R227 D607 R639 D204 U306 C610 C608 R603 D203 R235 D202 R234 R233 X202 S201 R510 R512 R322 R622 S601 L601 CB209 R353 R641 R607 R640 U202 R229 U601 R332 D201 X203 D508 D507 D506 D505 D504 D503 D501 D502 R308 U201 D604 CB601 R331 R330 P302 C304 C208 R431 CB314 R329 T302 R328 R371 CB204 CB207 JP201 R307 CB315 R325 R213 R231 R230 X301 R366 R432 R326 C607 1 2 3 4 5 6 7 8 XT201 R209 U204 R309 R312 CB309 U302 U303 CB316 R327 R515 R516 R517 R513 R514 R379 CB311 R311 R369 CB312 R323 R370 R321 R324 CB313 R511 CB404 CB402 C303 D401 T301 R367 R316 R317 R315 R314 P301 CB310 R518 R434 R433 R372 R310 R368 X403 X401 R439 R210 R313 R318 D403 D402 R408 X402 1 CB203 R405 C401 R401 X701 1 R406 L401 C207 U402 CB401 R621 R402 R403 R404 C602 C604 CB406 P401 S202 R356 R354 R608 R602 X601 C611 X703 1 Location of general optional resistors on Top Side X801 X804 1 C618 U401 R412 U404 R423 R418 R609 CB301 CB307 Q602 R301 R623 R624 R606 R628 Q603 R627 D609 D602 C605 C609 R605 R616 D608 Q601 X803 1 User’s Manual U301 CB305 R360 R620 X802 Figure 4-4 CB303 R346 CB304 R359 CB308 R303 R351 CB302 R348 CB306 R302 Q406 Q404 Q402 Q405 Q403 Q401 R338 R340 R344 U305 L301 L302 R349 C614 U603 R519 C301 R352 R350 R604 R617 R520 R429 C606 R619 R618 R507 R334 U304 R642 L602 CB629 R505 D603 R345 R411 R430 Y301 R638 R347 CB604 R613 R343 R319 C617 CB504 R342 R414 R424 C613 R644 R643 R438 Q604 R504 R437 CB318 R630 R502 R503 R509 CB503 CB506 CB508 R508 R529 R528 CB624 CB613 CB403 CB409 R416 R341 C615 R361 R320 Y401 CB408 R410 R335 R305 CB607 CB501 R440 R337 R333 R339 R523 R363 CB619 R527 R533 R534 CB502 R419 R365 R426 R626 R425 R336 R625 R306 CB317 R375 R634 R531 R530 CB608 C616 C204 C203 R205 R204 R358 CB605 CB614 CB620 R219 R216 R215 R221 CB610 CB602 CB626 CB202 CB612 R373 R378 R417 CB405 U403 C612 CB625 R254 R635 R532 R526 R629 R253 R236 R631 C201 CB621 R615 R636 CB606 CB617 R633 R611 R632 R610 R256 R255 R238 CB609 R202 R374 U602 R258 R376 R377 R612 CB507 R201 R362 R637 CB201 R257 R427 CB407 R415 R409 R420 R206 CB603 C202 Y201 R241 R208 R364 R436 R422 R428 R357 R211 C206 R243 CB615 CB206 C205 CB205 R252 Y202 R240 R239 R244 R207 R212 R247 CB622 C212 R246 R203 R304 R614 C209 R220 R521 C210 R217 C211 R248 R218 R224 R222 R251 R223 R250 R225 R522 R525 R226 R232 R435 R524 R421 1 C302 Figure 4-3 X702 1 C601 1 D601 Location of general optional resistors on Bottom Side 4-5 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration Table 4-4 Resistors for peripherals Component Description R333 Connect P3.12 with RXD of CAN0 transceiver (default: assembled) R339 Connect P3.14 with RXD of CAN1 transceiver (default: assembled) R353 Connect P3.5 (SLSO00) with /CS of Eeprom (default: assembled) R345 Connect P2.3 (MLI0) with IFlex (default: assembled) R346 Connect P2.0 (MLI0) with IFlex (default: assembled) R347 Connect P2.2 (MLI0) with IFlex (default: assembled) R348 Connect P2.1 (MLI0) with IFlex (default: assembled) R349 Connect P2.7 (MLI0) with IFlex (default: assembled) R350 Connect P2.4 (MLI0) with IFlex (default: assembled) R351 Connect P2.6 (MLI0) with IFlex (default: assembled) R352 Connect P2.5 (MLI0) with IFlex (default: assembled) R357 Connect P2.12 (SSC1) with IFlex (default: not assembled) R358 Connect P2.10 (SSC1) with IFlex (default: not assembled) R359 Connect P3.6 (SSC1) with IFlex (default: not assembled) R361 Connect P2.11 (SSC1) with IFlex (default: not assembled) R360 Connect P0.6 (REQ2) with IFlex (default: not assembled) R440 Connect P3.0 with TXD of USB to UART (default: assembled) R505 Connect VAREF0 with VDDM (default: assembled) R507 Connect VAGND0 with VSSM (default: assembled) R508 Connect VFAREF with VDDMF (default: assembled if not with TC1387) R509 Connect VFAGND with VSSMF (default: assembled if not with TC1387) R519 Connect +5V with VDDM (default: assembled on TC1767, TC1782 and TC1387) R520 Connect +3,3V with VDDM (default: assembled if not TC1767, TC1782 or TC1387) User’s Manual 4-6 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration Note: All resistors are red marked in the following figures R407 X704 U601 D205 R249 R245 JP202 U203 R639 CB319 R237 R355 JP203 R601 R501 D204 U306 C610 C608 X201 D606 D605 R228 C603 R229 R603 D203 R235 D202 R234 R233 X202 S201 R510 R512 R227 D607 JP201 R622 S601 D201 X203 D508 D507 D506 D505 D504 D503 D501 X302 CB209 R353 R641 R607 R640 U202 CB208 D604 CB601 R331 R332 L601 R330 P302 D502 R308 U201 R322 R312 CB315 R325 C304 C208 R431 CB314 R329 T302 R328 R371 CB204 CB207 R242 R432 R213 R231 R230 X301 R307 R309 R326 C607 1 2 3 4 5 6 7 8 XT201 R209 U204 R366 T301 R367 CB309 U302 U303 CB316 R327 R515 R516 R517 R513 R514 R379 CB311 R311 R369 CB312 R323 R370 R321 R324 CB313 R511 CB404 CB402 C303 D401 R317 R316 R315 R314 P301 CB310 R518 R434 R433 R372 R310 R368 X403 X401 R439 R210 R313 R318 D403 D402 R408 X402 1 CB203 R405 C401 R401 X701 1 R406 L401 C207 U402 CB401 C602 C604 R402 R403 R404 R621 CB406 P401 S202 R356 R354 R608 R602 X601 C611 X703 1 Location of peripheral resistors on Top Side X801 X804 1 U401 R412 U404 R423 R418 R609 CB301 CB307 U301 CB303 R346 CB305 R360 Q602 CB304 R359 CB308 R303 R351 CB302 R348 CB306 R301 R623 R624 R606 R628 Q603 R627 D609 D602 C605 C609 R605 R616 D608 R302 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 R340 R344 U305 L301 L302 R349 Q601 X802 X803 1 User’s Manual C301 R352 R620 Figure 4-6 R429 Y301 C606 C618 R430 C614 R519 R411 R350 R604 R617 R520 R424 R638 U603 R507 L602 R505 CB629 D603 R619 R618 CB604 R613 U304 R642 C617 CB504 R345 R414 R341 C615 R347 R416 C613 R644 R643 R319 CB403 CB409 R410 R335 R440 R337 R504 R342 Q604 R509 CB503 R508 CB506 CB508 R438 R343 R502 R503 CB501 Y401 CB408 R437 CB318 R630 CB624 CB613 CB317 R361 R320 R339 R523 R634 R531 R305 CB607 R527 R533 R534 CB502 R333 CB619 R529 R528 R530 CB608 C616 C204 R205 R204 C203 R215 R358 CB605 CB620 R219 R216 R221 CB610 CB602 CB626 CB202 CB612 R363 CB405 U403 C612 CB625 R254 R635 R532 R526 R629 R253 R236 R631 C201 CB621 R615 R636 CB606 CB617 CB507 CB609 R633 R611 R632 R610 R256 R255 R238 R375 U602 R258 R378 R637 CB201 R257 R427 CB407 R201 R417 R362 R202 R419 R376 R365 R426 R374 R626 R425 R336 R373 R306 R625 R377 R612 CB603 C202 Y201 R241 R208 R428 R206 R211 C206 R243 CB615 CB206 C205 R252 Y202 CB205 R240 R239 R244 R207 R212 R247 CB622 C212 R246 R364 R436 R422 R415 R409 R420 R357 R304 R614 C209 R203 CB614 R521 C210 R220 R218 C211 R248 R217 R222 R223 R251 R224 R250 R225 R522 R525 R226 R232 R435 R524 R421 1 C302 Figure 4-5 X702 1 C601 1 D601 Location of peripheral resistors on Bottom Side 4-7 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Configuration Table 4-5 Resistors for safety device Component Description R247 Connect potentiometer to sensor input C (default: assembled) R251 Connect potentiometer to sensor input D (default: assembled) R239/R240 Voltage divider to adapt VDDP to VAREF of safety device (default: assembled) R252 Connect P3.6 (SLSO01) with /CS of safety device (default: assembled) R253 Connect P3.2 (SSC0) to SCLK of safety device (default: assembled) R254 Connect P2.11 (SSC1) to SCLK of safety device (default: not assembled) R255 Connect P3.4 (SSC0) to MTSR of safety device (default: assembled) R256 Connect P2.12 (SSC1) to MTSR of safety device (default: not assembled) R257 Connect P3.3 (SSC0) to MRST of safety device (default: not assembled) R258 Connect P2.10 (SSC1) to MRST of safety device (default: not assembled) Note: All resistors are red marked in the following figures X801 X804 1 C618 U401 R412 R435 U404 Q602 R301 R623 R624 R606 R628 R604 Q603 R627 CB301 CB303 D609 D602 C605 C609 R605 D608 Q601 X802 X803 1 User’s Manual CB307 CB305 R360 R302 R346 U301 R359 CB304 R340 R344 R609 R351 CB302 R348 CB306 CB308 R303 L302 R349 R620 Figure 4-7 C302 R418 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 L301 R350 R638 R519 C301 Y301 R352 R616 R617 R520 R429 C614 U603 R507 R411 R430 C606 R619 R618 L602 CB629 R505 D603 R337 R642 CB604 R613 R345 R424 C613 R347 C617 CB504 R343 R319 R414 C612 R644 R643 R438 R342 R339 R630 R504 R437 CB318 CB506 CB508 R509 CB503 R529 R528 R502 R503 R416 R335 R361 R320 CB403 CB409 R410 R341 C615 R305 CB607 CB501 R440 R333 R336 U304 R363 CB624 CB613 R419 R625 Q604 R523 R634 R425 CB619 R527 R533 R534 CB502 R426 CB317 R306 R417 Y401 CB408 U305 R365 R626 R373 R375 R508 R531 R530 CB608 C616 C204 C203 R205 R204 R219 R216 R215 R358 CB605 CB614 CB620 R221 CB610 CB602 CB626 CB202 CB612 R202 R374 U602 CB625 R254 R635 R631 R253 R236 R532 R526 R633 R611 R632 R610 R255 R238 C201 CB621 R615 R636 CB606 CB617 R378 R612 CB507 CB609 R629 R258 R256 R376 R377 R637 CB201 R257 R201 R362 CB405 U403 R427 CB407 R415 R409 R420 R206 CB603 C202 Y201 R241 R208 R364 R428 R357 R211 C206 R243 CB615 CB206 C205 CB205 R252 Y202 R240 R239 R244 R207 R212 R247 CB622 C212 R246 R203 R304 R614 C209 R220 R521 C210 R217 C211 R248 R218 R224 R222 R251 R223 R250 R225 R522 R525 R226 R232 R436 R422 R423 R524 R421 1 1 D601 Location of resistors for safety device on Bottom Side 4-8 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Software 5 TriBoard Software 5.1 Requirements To install the software from your TriBoard CD you need a PC with Windows95/98/ME, Windows 2000, Windows XP or Windows Vista. 5.2 Software Overview The CD does not contain any tool. For the availablity for Demo Versions of the different Tools, please contact the toolvendor directly (e.g. Tasking, Hitex, Lauterbach, GreenHills, HighTec...). To install tools for compiling and debugging use seperat CD’s from Toolvendors. There are also some application notes and software examples. The data sheets of all used parts can be found in the “TriBoard_Components” directory. The manuals for the microcontrollers and the Easy Kit are located in the “Manual” folder. Some useful tools like Acrobat Reader are stored in the “Utilities” directory. The current Errata Sheet can be found in the directory “Errata Sheet”. To make sure you have always the most recent one, please contact your local FAE. Note: For more details see the file ReadMe.txt. 5.3 Software Installation To install tools for the TriCore insert the CD from the Toolvendor and start the file “setup.exe” if the CD is not automatically started. Follow the instructions of the installationprogram. User’s Manual 5-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual TriBoard Software User’s Manual 5-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Signal Description 6 Signal Description For more information about the signals please see the user manuals from TC176X/TC116X/TC1782/TC1387 and/or the schematics of the board. Table 6-1 Power Signals Short Name Description VCC_IN Supply Input (5,5V...50V(40V)) VIN Input voltage of power supply device GND Ground VDD Core Supply Voltage (1,3V or 1,5V) VDDP Port Supply Voltage (3,3V) VDDFL3 Flash Supply Voltage (3,3V) VDDESB Emulation Stand-by SRAM Supply Voltage (1,3V or 1,5V) VDDOSC Main Oscillator Supply Voltage (1,3V or 1,5V) VDDOSC3 Main Oscillator Supply Voltage (3,3V) VSSOSC Main Oscillator Ground VSSM ADC Analog Part Ground VDDM ADC Analog Part Supply Voltage (5V for TC1767, TC1782 and TC1387 other 3,3V) VSSMF FADC Analog Part Ground VDDMF FADC Analog Part Supply Voltage (3,3V) VDDAF FADC Analog Part Logic Supply Voltage (1,3V or 1,5V) VAGND0 ADC0 Reference Ground VAREF0 ADC0 Reference Voltage (VDDM) VFAGND FADC Reference Ground VFAREF FADC Reference Voltage (VDDMF) VDDP_CIC Port Supply Voltage safety device (3,3V) VAGND_CIC ADC Reference Ground safety device VAREF_CIC ADC Reference Voltage safety device (2,5V) Table 6-2 Reset Signals Short Name Description /PORST Power On Reset /HDRST (ESR0) Hardware Reset User’s Manual 6-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Signal Description Table 6-3 Interrupt Signals Short Name Description /NMI (ESR1) Non Maskable Interrupt /RESET_CIC Reset safety device Table 6-4 Clock Signals Short Name Description XTAL1 Crystal Oscillator Input XTAL2 Crystal Oscillator Output XTAL1_CIC Crystal Oscillator Input safety device XTAL2_CIC Crystal Oscillator Output safety device Table 6-5 Debug Signals Short Name Description /TRST Test Reset TCLK Test Clock TMS Test Mode Select TDI Test Data Input TDO Test Data Output /TESTMODE Test Mode Select Input /BRKIN TriCore Breakpoint Input /BRKOUT TriCore Breakpoint Output TCLK_CIC Test Clock safety device TMS_CIC Test Mode Select safety device TDI_CIC Test Data Input safety device TDO_CIC Test Data Outpu safety device MBC_CIC Monitor & Bootstrap loader Control line safety device Table 6-6 Peripheral Signals Short Name Description P3.1 Transmit Data ASC0 P3.0 Receive Data ASC0 P3.8 Transmit Data ASC1 P3.9 Receive Data ASC1 User’s Manual 6-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Signal Description Table 6-6 Peripheral Signals P3.2 Clock Line SSC0 P3.3 Master Receive / Slave Transmit SSC0 P3.4 Master Transmit / Slave Receive SSC0 P3.5 Slave Select Output 0 (SSC0) P3.13 CAN Transmitter Output 0 P3.12 CAN Receiver Input 0 P3.15 CAN Transmitter Output 1 P3.14 CAN Receiver Input 1 P2.4 MLI0 receive channel clock P2.5 MLI0 receive channel ready output P2.6 MLI0 receive channel valid input P2.7 MLI0 receive channel data input P2.0 MLI0 transmit channel clock P2.1 MLI0 transmit channel ready input P2.2 MLI0 transmit channel valid output P2.3 MLI0 transmit channel data output P2.11 Clock Line SSC0 P2.10 Master Receive / Slave Transmit SSC0 P2.12 Master Transmit / Slave Receive SSC0 P3.6 Slave Select Output 1 (SSC1) P0 [0...7] General Purpose I/O Port 0 (HWCFG on TC1767, TC1782 and TC1387 else SWOPT) P0 [8...15] General Purpose I/O Port 0 (SWOPT if not TC1767, TC1782 or TC1387) P1[0...15] General Purpose I/O Port 1 P2[0...13] General Purpose I/O Port 2 P3[0...15] General Purpose I/O Port 3 P4[0...3] General Purpose I/O Port 4 (HWCFG if not TC1767, TC1782 or TC1387) P5[0...7] General Purpose I/O Port 5 (used for LEDs) P5[8...15] General Purpose I/O Port 5 AN[0...35] Analog Inputs User’s Manual 6-3 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Signal Description Table 6-6 Peripheral Signals P6.1 / FCLP0A MSC0 differential driver clock output positive A P6.0 / FCLN0 MSC0 differential driver clock output negative P6.3 / SOP0A MSC0 differential driver serial data output positive A P6.2 / SON0 MSC0 differential driver serial data output negative Table 6-7 Safety device Signals Short Name Description SENA Sensor Input A SENB Sensor Input B SENC Sensor Input C SEND Sensor Input D SCLK_CIC Clock Line SAK-CIC61508 MRST_CIC Master Receive / Slave Transmit SAK-CIC61508 MTSR_CIC Master Transmit / Slave Receive SAK-CIC61508 /CS_CIC Slave Select Input SAK-CIC61508 SYSDISA System Disable Output A SYSDISB System Disable Output B SYSDISC System Disable Output C User’s Manual 6-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Connector Pin Assignment 7 Connector Pin Assignment The TriBoard will be shipped with four male (plug) connectors on top layer and four female (socket) connectors on bottom layer. The default connectors are 80-pol. Board to Board connectors from Samtec: http://www.samtec.com Plug: FTSH-140-02-L-DV-ES-A Socket: FLE-140-01-G-DV-A Alternative there can be used the Board to Board System from Robinson Nugent: http://www.robinsonnugent.com Plug: P50L-80P-AS-TGF Socket: P50L-80S-AS-TGF Note: All connectors are pincompatible with the previous versions of TriBoard TC176X. User’s Manual 7-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Connector Pin Assignment 7.1 TC176X/TC116X Connector / Top View BUS EXPANSION (X801,X901) GND GND Figure 7-1 User’s Manual 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 PERIPHERALS (X802,X902) GND GND GND GND VCC_IN VCC_IN /ESR1 GND EN00 / P2.8 SDI0 / P2.13 FCLP0A / P6.1 FCLN0 / P6.0 SOP0A / P6.3 SON0 / P6.2 SLSO00_10 / P3.5 SLSO02_12 / P3.7 SLSO04_14 / P2.8 SLSO06 / P3.8 GND XTAL1 XTAL2 RXD0 / P3.0 TXD0 / P3.1 RXDCAN0 / P3.12 TXDCAN0 / P3.13 SCLK0 / P3.2 MTSR0 / P3.4 MRST0 / P3.3 REQ0 / P3.10 REQ2 / P0.6 VDDESB 3V3 3V3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GND GND VCC_IN VCC_IN /ESR0 GND /PORST EN01 / P2.9 SLSI1 / P2.13 SLSO01_11 / P3.6 SLSO03_13 / P2.1 SLSO05_15 / P2.9 SLSO17 / P1.10 GND SYSCLK / P4.3 RXD1 / P3.9 TXD1 / P3.8 RXDCAN1 / P3.14 TXDCAN1 / P3.15 SCLK1 / P2.11 MTSR1 / P2.12 MRST1 / P2.10 REQ1 / P3.11 REQ3 / P0.7 GND 3V3 3V3 Connector for TC176X/TC116X/TC1782/TC1387 - Pinout (Part I, Top View) 7-2 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Connector Pin Assignment ADC (X803, X903) VSSM VSSM AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 VSSM VDDM VFAGND VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 VSSM 61 63 65 67 3V3 69 AD0EMUX0 / P1.12 71 AD0EMUX1 / P1.13 73 AD0EMUX2 / P1.14 75 77 REQ5 / P0.15 79 Figure 7-2 User’s Manual 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GPTA / MLI (X804,X904) VSSM VSSM AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSMF VDDMF VFAREF VAGND0 GND GND GPTA0 / P0.0 GPTA1 / P0.1 GPTA2 / P0.2 GPTA3 / P0.3 GPTA4 / P0.4 GPTA5 / P0.5 GPTA6 / P0.6 GPTA7 / P0.7 GPTA8 / P0.8 GPTA9 / P0.9 GPTA10 / P0.10 GPTA11 / P0.11 GPTA12 / P0.12 GPTA13 / P0.13 GPTA14 / P0.14 GPTA15 / P0.15 GPTA16 / P1.0 GPTA17 / P1.1 GPTA18 / P1.2 GPTA19 / P1.3 GPTA20 / P1.4 GPTA21 / P1.5 GPTA22 / P1.6 GPTA23 / P1.7 GPTA24 / P1.8 GPTA25 / P1.9 GPTA26 / P1.10 GPTA27 / P1.11 GPTA28 / P4.0 GPTA29 / P4.1 GPTA30 / P4.2 GPTA31 / P4.3 TCLK1 / P5.11 TREADY1 / P5.10 TVALID1 / P5.9 TDATA1 / P5.8 3V3 3V3 VSSM VSSM 3V3 REQ4 / P0.14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 GND GND GPTA32 / P2.0 GPTA33 / P2.1 GPTA34 / P2.2 GPTA35 / P2.3 GPTA36 / P2.4 GPTA37 / P2.5 GPTA38 / P2.6 GPTA39 / P2.7 GPTA40 / P5.0 GPTA41 / P5.1 GPTA42 / P5.2 GPTA43 / P5.3 GPTA44 / P5.4 GPTA45 / P5.5 GPTA46 / P5.6 GPTA47 / P5.7 EMGSTOP / P1.4 RDATA1 / P5.12 RVALID1 / P5.13 RREADY1/ P5.14 RCLK1 / P5.15 3V3 3V3 Connector for TC176X/TC116X/TC1782/TC1387 - Pinout (Part II, Top View) 7-3 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Connector Pin Assignment 7.2 Power connector pinout +5,5V...50V(40V) GND Figure 7-3 USB connector pinout Figure 7-4 7.4 2 (D-) 1 (Vbus) 3 (D+) 4 (GND) USB connector Pinout Flexray Pinout 6 Figure 7-5 User’s Manual BP 2 BM 1 7 8 3 9 4 5 GND 7.3 Power connector pinout Flexray Pinout (SUBD-9 Plug) 7-4 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Connector Pin Assignment CAN connector pinout 4 6 8 1 0 1 3 5 7 9 Figure 7-6 CAN connector pinout (IDC10) GND /PORST GND GND 8 10 12 14 16 1 3 5 7 9 11 13 15 TCK TDI /BRKIN 6 /TRST 4 OCDS connector pinout (IDC16) User’s Manual Key GND GND 8 10 1 3 5 7 9 /RESET 6 USR1_IN 4 USR0_IO 2 DAP0 DAP1 Figure 7-8 GND DAP connector pinout (only with TC1767, TC1782, TC1387) +3V3 7.7 2 TDO TMS Figure 7-7 /BRKOUT OCDS connector pinout +3V3 7.6 GND CANH CANL 2 GND 7.5 DAP connector pinout (FTSH10) - only with TC1767, TC1782, TC1387 7-5 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Connector Pin Assignment User’s Manual 7-6 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout 8 Schematic and Layout 8.1 Schematic 8.1.1 New and changes on schematic version V2.1 to TriBoard TC176X/TC116X/TC1782/TC1387 V2.0 • add other power regulator for +1,3V core voltage on TC1782 (other devices not affected User’s Manual 8-1 V 2.1, 2009-06 Figure 8-1 User’s Manual 8-2 A B C D 1 1 /ESR0_/HDRST PORT[0..9] 2 /TESTMODE JTAG.. /ESR0_/HDRST /PORST MiniWiggler and DAP OCDS.sch Clk_Cfg_Jtag.sch 4 5 6 6 3 XTAL[1..2] /TESTMODE JTAG.. PORT[0..9] Clock. Config and Jtag PORT[0..9] /ESR0_/HDRST IFLEX, CAN and Eeprom BUS..CTRL NC1[0..80] NC2[0..80] NC3[0..80] NC4[0..80] 8 of 8 8 A B C D 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\TriBoard_LQFP176_V21.prj Sheet: Infineon Technologies AG XTAL[1..2] /ESR0_/HDRST /PORST /ESR1_/NMI AN[0..35] TriBoard LQFP176 Project PORT[0..9] BUS..CTRL AD[0..15] A[0..20] XTAL[1..2] /ESR0_/HDRST /PORST /ESR1_/NMI AN[0..35] Connector Socket NC4[0..80] NC3[0..80] NC2[0..80] NC1[0..80] Connectf.sch 7 Connector Plug PORT[0..9] Connectm.sch A[0..20] IFlex_CAN_Eeprom.sch 5 /PORST PORT[0..9] 4 AD[0..15] POWER SUPPLY PORT[0..9] 3 /ESR1_/NMI Supply.sch AN[0..35] GPTA/MSC/MLI/ADC GPTA_ADC.sch 2 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - Project V 2.1, 2009-06 A B C D 1 TDO_CIC SYSDISB SYSDISA VDDP_CIC GND VAGND_CIC VAREF_CIC SEND P1_0_CIC P1_1_CIC P1_5_CIC /CS_CIC P3_7_CIC SYSDISB SYSDISA P3_2_CIC P3_3_CIC P3_4_CIC P3_5_CIC /RESET_CIC P2_3_CIC P2_4_CIC P2_5_CIC P2_6_CIC P1_6_CIC P1_7_CIC TMS_CIC TCK_CIC TDO_CIC TDI_CIC SENA SENB SENC R227 10K MBC_CIC SCLK_CIC MTSR_CIC MRST_CIC XTAL2_CIC XTAL1_CIC GND VDDC_CIC CON1X19_opt 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 X202 620R R235 620R R234 620R R233 GND C212 10nF SEND GND C211 10nF SENC VDDP_CIC LS T67K D203 LS T67K D202 CON1X19_opt 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 X201 GND 0R R251 0R R247 LS T67K D201 VAGND_CIC R250 0R 10K 2 R249 R248 0R VAREF_CIC VAGND_CIC R246 0R 10K 2 R245 R244 0R VAREF_CIC 3 1 3 1 2 3 4 SCLK_CIC MTSR_CIC MRST_CIC VAGND_CIC 2 CB206 100n 24 25 27 28 29 9 10 1 11 12 13 14 MBC_CIC TMS_CIC TCK_CIC TDO_CIC TDI_CIC P1_0_CIC P1_1_CIC P1_5_CIC P1_6_CIC P1_7_CIC VAREF_CIC 5 38 /RESET_CIC S202 620R VAGND_CIC R243 0R R242 10K SAK-CIC61508 VAGND VAREF P1.0 / RXD_0 P1.1 / TXD_0 P1.5 P1.6 P1.7 P0.3 / SCLK_1 P0.4 / MTSR_1 P0.5 / MRST_1 MBC TMS P0.0 / TCK_0 P0.2 / TDO_0 P0.1 / TDI_0 RESET XTAL2 XTAL1 U202 C206 CSTCR6M00G VSSP P2.7 / AN7 P2.6 / AN6 P2.5 / AN5 P2.4 / AN4 P2.3 / AN3 P2.2 / AN2 P2.1 / AN1 P2.0 / AN0 P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 VSSC VDDC 19 26 23 22 21 20 17 16 15 31 30 37 36 35 34 33 32 7 8 3 10 8 GND C203 33pF 0R 0R R205 GND GND /RESET_CIC MRST_CIC MTSR_CIC OUT GND SLEEP V+ GND OUT 0R 3 6 GND 4 1 3 5 7 9 11 13 15 0R R258 1 RESET JP203 R257 0R_opt 0R R255 0R_opt 0R_opt 0R R254 R256 R253 0R R252 OCDS1_CIC 2 TMS VCC TDO GND CPUCLOCK GND TDI PORST TRST BRKOUT TCK GND BRKIN OCDSE N.C. KEY X203 R230 GND opt C207 1uF VAREF_CIC GND C208 22µF/10V VDDP_CIC 3 VAGND_CIC R231 REF192GS GND SCLK_CIC /CS_CIC IN U204 MBC_CIC R232 1K TCK_CIC TDI_CIC TMS_CIC TDO_CIC CB205 220n 4 2 GND CB207 100n VDDP_CIC 1 CB209 100n VIN U203 TLE4274DV33 Y201 XTAL2 C201 opt opt 1 R206 opt VSSOSC 50R_opt R204 R203 C204 33pF GND GND 4 XTAL1 ONLY WITH TC1387 OR ON REQUEST P3_7_CIC GND /CS_CIC P3_5_CIC P3_4_CIC P3_3_CIC P3_2_CIC SYSDISA SYSDISB SEND P2_6_CIC P2_5_CIC P2_4_CIC P2_3_CIC SENC SENB SENA XTAL2 XTAL1 /TESTMODE Crystal 20MHz VCC VCC GND OE OE XT201 CB204 100n VDDC_CIC GND VDDP_CIC 11 14 7 1 4 XTAL[1..2] CB203 100n GND 18 3 /TESTMODE +3V3 GND VDDP 22pF_opt 22pF_opt C205 GND VDDP_CIC 2 R241 0R VAREF_CIC VAGND_CIC R238 0R R237 10K R236 0R Y202 2 GND 6 2 GND R228 JP202 SENB 1K R240 JP201 SENA VAREF_CIC RESET_CIC CB208 100n R229 10K XTAL2_CIC XTAL1_CIC XTAL2_CIC XTAL1_CIC D204 LS T67K VDDP_CIC GND /RESET_CIC 2 1K6 R239 2 C210 10nF VDDP GND C209 10nF /RESET_CIC SENB SENA VDDCORE 1 3 1 3 2 1 8-3 3 3 1 3 1 User’s Manual GND Figure 8-2 2 1 C202 opt /PORST P2_10 P3_3 P2_12 P3_4 P2_11 P3_2 P3_6 5 VDDP_CIC 2 4 GND 6 /RESET_CIC 8 MBC_CIC 10 12 GND 14 16 GND D205 LP T67K R213 680R VSSOSC 2 R207 opt XTAL2 XTAL1 GND R202 opt R201 10K +3V3 5 P3_10 137 P3_11 144 P2_10 161 130 P3_14 134 P3_12 143 138 P3_9 JTAG / DAP / OCDS1 VSSOSC VDDOSC VDDOSC3 CLOCK & TESTMODE VDD P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 P4_3 P4_2 P4_1 P4_0 P2.10 / IN10 / OUT0 / MRST1A P3.1 / OUT85 / TXD0A P3.8 / SLSO06 / OUT90 / TXD1 P3.4 / OUT88 / MTSR0 P3.2 / OUT86 / SCLK0 P3.15 / OUT97 / TXDCAN1 / TXD1 P3.13 / OUT95 / TXDCAN0 / TXD0 P3.5 / SLSO00_10 P3.6 / SLSO01_11 P3.7 / SLSI01 / OUT89 / SLSO02_12 JTAG.. VSSOSC 1 of 8 GND R210 10K R209 10K 135 126 127 131 163 162 132 129 133 142 128 P3_5 P3_6 P3_7 P2_12 P2_11 P3_4 P3_2 P3_15 P3_13 P3_8 P3_1 CFG0 CFG1 CFG2 CFG3 CFG4 CFG5 CFG6 CFG7 1 2 3 4 5 6 7 8 Infineon Technologies AG 1 GND 16 15 14 13 12 11 10 9 PORT[0..9] DIPSW-8 S201 Switch ON means the corresponding signal is low. Switch OFF means the corresponding signal is high. 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\Clk_Cfg_Jtag.sch Sheet: 0R +3V3 GND R210 NOT WITH TC1767, TC178X AND TC1387 /TRST TriBoard LQFP176 Clock, Config, Jtag and CIC61508 TC176X/TC116X/TC178X/TC1387-LQFP176 P3.10 / OUT92 / REQ0 P3.11 / OUT93 / REQ1 680R R226 680R R224 680R R222 680R R220 P2.12 / IN12 / OUT2 / MTSR1A / SOP0B P2.11 / IN11 / OUT1 / SCLK1A / FCLP0B P3.14 / OUT96 / RXDCAN1 / RXD1B P3.3 / OUT87 / MRST0 680R R225 680R R223 680R R221 680R R219 ASC / CAN / SSC / EXT. REQ P3.12 / OUT94 / RXDCAN0 / RXD0B P3.9 / OUT91 / RXD1A 6 680R R218 680R R216 ONLY WITH TC1767, TC178X AND TC1387 680R R217 680R R215 NOT WITH TC1767, TC178X AND TC1387 R211 CB201 0R 330n R208 VDDOSC3 8 R209 ONLY WITH TC1767, TC178X AND TC1387 +3V3 R212 CB202 0R 330n VSSOSC 113 TDO 104 VDDOSC 105 106 7 NOTE: S201 is for boot configuration (about configuration see the manual of assembled device). TC176X/TC116X/TC178X/TC1387-LQFP176 P1.15 / BRKIN / BRKOUT TRST TDO / DAP2 / BRKIN / BRKOUT TCK / DAP0 TMS / DAP1 TDI / BRKIN / BRKOUT XTAL2 XTAL1 TESTMODE U201B P3.0 / OUT84 / RXD0A U201C P1_15 136 P3_3 114 115 112 111 103 102 118 P1_15 117 P3_0 /TRST TCK TMS TDI XTAL2 XTAL1 /TESTMODE 6 A B C D TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - Config, Clock and CIC61508 V 2.1, 2009-06 A B C D 1 /ESR0_/HDRST 0R 0R R352 R363 +3V3 4K7 R302 /ESR0_/HDRST P2_5 P0_7 0R R301 GND 4K7 P0_11 R362 48 47 61 52 51 50 49 33 29 21 20 19 18 60 31 62 45 34 32 30 28 27 23 22 59 58 54 53 44 43 40 39 38 37 36 35 0R 0R 0R 0R R351 0R P2_6 P2_4 P2_7 P2_11 P2_1 P0_6 P2_2 P3_6 P2_0 P2_10 P2_3 P2_12 P2_10 P3_6 P0_6 P2_11 +3V3 10K R356 10K R355 GND CB319 100n +3V3 GND Y301 12pF 20MHz 1 C301 2 GND 12pF C302 R303 0R 2 NOT WITH TC178X AND TC1387 PORST JTAGEN 3 VSSOSC / VSSPOSC P1.0 / D0 / TVALIDB P0.3 / TXDA / TCLK P1.1 / D1 / TCLK P0.1 / TXENA / RVALIDC / TCK P1.2 / D2 / TDATA / SCLK P0.5 / RXDA / RCLKC P1.3 / D3 / RREADYB / RDY P0.7 / BGEA / SR13 / TREADYC / TMS P1.4 / D4 / RVALIDB / SLS P1.5 / D5 / RCLKB / MRST / DIR P0.2 / TXDB / TDATA P1.6 / D6 / RDATAB / MTSR P0.0 / TXENB / TVALIDC / TDO P1.7 / D7 / MODE1 P0.4 / RXDB / RDATAC P0.6 / BGEB / SR14 P1.8 / D8 / SR0 P1.9 / D9 / SR1 P0.9 / ARM / SR12 P1.10 / D10 / SR2 P0.10 / MT / SR11 P1.11 / D11 / SR3 P0.11 / BGT / RREADYC / SR10 / TDI P1.12 / D12 / SR7 P1.13 / D13 / SR6 P1.14 / D14 / SR5 VDDP P1.15 / D15 / SR4 VDDP VDDP VDDP P2.1 / A1 P2.2 / A2 VDD P2.3 / A3 VDD P2.4 / A4 P2.5 / A5 P2.6 / A6 VSSP / VSSB P2.7 / A7 VSSP / VSSB / VSS P2.8 / A8 VSSP / VSSB P2.9 / A9 VSSP / VSSB / VSS P2.10 / A10 P2.11 / A11 P0.8 / TRST / SR8 / A12 VDDAPLL / VDDOSC P2.12 / BYPASS / CSFPI P2.0 / BC0 P2.14 / BC1 / TREADYB VSSAPLL P2.15 / RD P2.13 / WR P0.13 / WAIT VDDPOSC U301 SAKCIC310 0R 0R R350 0R_opt R349 R361 0R_opt R348 R360 0R_opt R347 R359 0R_opt R346 R358 0R_opt R345 R357 NOT WITH TC178X AND TC1387 3 TXDB TXENB RXDB BGEB ERRNA ERRNB 5 1 3 15 17 16 64 11 14 9 GND 10 GND R372 0R 0R GND R365 R373 0R GND CB308 100n VDD GND +3V3 R304 4K7 +3V3 MMZ1608R300A L302 MMZ1608R300A L301 GND CB307 100n GND GND GND VDD 24 57 CB301 8 25 42 56 1 6 5 2 4 0R R354 100K R353 +3V3 P3_5 P3_2 P3_4 P3_3 4 0R R364 P3_10 R374 0R P0_15 P3_11 R375 0R P0_11 P0_13 ONLY WITH TC178X AND TC1387 P0_9 +3V3 TXDA TXENA RXDA BGEA 7 26 41 55 CS SCK SI SO AT25128N-10SI2.7 HOLD WP VCC GND U306 6 2 4 63 7 3 8 4 100n CB302 100n CB303 100n CB304 100n CB305 100n CB306 100n PORT[0..10] XTAL1 12 P1_7 P1_5 P1_6 P1_4 R307 4K7 +3V3 P0_10 P0_12 P0_8 P0_14 P3_15 P3_14 P3_13 P3_12 0R R339 0R R333 5 GND 4K7 R313 opt INH1A INH2A WAKEA 4K7 9 3 5 6 7 8 2 1 15 GND R327 opt INH1B INH2B WAKEB 2 1 15 4K7 STBNB 13 ERRNB RXENB 12 R323 TXDB TXENB RXDB BGEB ENB +3V3 R322 R321 4K7 +3V3 R326 opt 9 3 5 6 7 8 4K7 STBNA ERRNA 13 RXENA 12 R309 GND R312 opt GND R325 opt GND R324 opt 0R_opt 0R_opt R320 R319 GND GND TXDA TXENA RXDA BGEA ENA +3V3 R308 R379 0R GND R311 opt R378 0R GND R310 opt 0R_opt 0R_opt R306 R305 R377 0R GND R376 0R ONLY WITH TC178X AND TC1387 5 AS8221 6 INH1 INH2 WAKE ERRN RXEN STBN EN TXD TXDEN RXD BGE U303 AS8221 INH1 INH2 WAKE ERRN RXEN STBN EN 1 2 3 4 GND TXD TXDEN RXD BGE U302 100n 1 2 3 4 GND CB318 +5V 100n CB317 +5V 6 GND VBAT VDD VIO NU / VBUF BM BP NU / TRXD1 NU / TRXD0 GND VBAT VDD VIO NU / VBUF BM BP NU / TRXD1 NU / TRXD0 0R R340 6 8 5 7 6 8 5 7 R341 0R +3V3 R335 0R R337 0R R342 0R 120R R344 R343 0R VIN 0R GND opt T301 R314 3 2 +5V GND +3V3 GND opt 0R R368 B82790-C0513-N201 R315 4 1 GND GND +5V VIN 0R GND +5V GND opt T302 R328 3 2 +3V3 GND +5V C304 10nF R332 0R GND R330 51R ONLY WITH NXP TJA1080 GND 0R R371 opt B82790-C0513-N201 R329 4 1 GND R331 51R C303 10nF R317 51R 2 of 8 7 Infineon Technologies AG GND GND X2 5 9 4 8 3 7 2 6 1 X1 X2 5 9 4 8 3 7 2 6 1 X1 GND GND CHANNELB P302 CHANNELA P301 8 A B C D 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\IFlex_CAN_Eeprom.sch Sheet: TriBoard LQFP176 IFlex, CAN and Eeprom GND 16 14 19 4 20 17 BMB 18 BPB 10 11 0R R370 R369 2 4 6 8 10 2 4 6 8 10 R318 0R GND R316 51R CAN1 1 3 5 7 9 X302 CAN0 1 3 5 7 9 X301 ONLY WITH NXP TJA1080 ONLY WITH NXP TJA1080 GND 16 14 19 4 20 17 BMA 18 BPA 10 11 0R R367 R366 7 R336 0R 120R R338 ONLY WITH NXP TJA1080 TLE6250GV33 TXD CANL GND INH VCC RM RXD CANH U305 0R R334 TLE6250GV33 TXD CANL GND INH VCC RM RXD CANH U304 +3V3 CB309 100n CB313 100n P2_7 P2_1 P2_2 P2_0 P2_3 XTAL2 13 CB311 100n 2 P0.12 / MODE0 / SR9 46 CB310 100n CB314 100n 8-4 CB312 100n User’s Manual CB315 100n Figure 8-3 CB316 100n 1 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - IFlex, CAN and Eeprom V 2.1, 2009-06 8-5 A B C D 1 PORT[0..10] R405 10K VDD_USB GND CB406 100n VDD_USB 1 2 3 4 7 4 8 5 ORG CS CLK D GND 10n CB401 93LC46B-I/SN DNC Q VCC GND U402 USB Connector P401 6 1 2 3 2 C401 10µ/6V 2K2 opt R406 R407 33n CB405 2 P1_15 P1_15 P1_15 P1_15 PIN116 PWREN TEST EECS EESK EEDATA RESET XTOUT XTIN RSTOUT USBDP USBDM 3V3OUT 100n PIN116 41 47 48 1 2 4 44 43 5 7 8 6 GND CB402 100n 0R_opt R429 0R_opt R427 0R_opt R425 0R_opt R424 0R_opt R423 3 0R_opt R430 USR1_DAP 0R_opt R428 USR1 /TESTMODE /TESTMODE /TESTMODE +3V3 2 4 6 /DBGRST 8 /BRKOUT 10 12 GND 14 16 GND BDBUS0 BDBUS1 40 39 38 37 36 35 33 32 1K R414 OCDS1 4 /TESTMODE VCC TMS GND TDO GND CPUCLOCK PORST TDI BRKOUT TRST GND TCK OCDSE BRKIN KEY N.C. X401 VDD_USB 10K D401 LS T67K R411 1K5 VDD_USB VDD_USB R408 ACBUS0 ACBUS1 ACBUS2 ACBUS3 15 13 12 11 10 30 29 28 27 26 ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 24 23 22 21 20 19 17 16 FT2232D BCBUS0 BCBUS1 BCBUS2 BCBUS3 SI/WUB BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 SI/WUA ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 100n GND U401 GND CB404 0R_opt R426 /BRKIN USR2 GND 470R R401 100n CB409 4 10K R418 /BRKIN /TESTMODE 1 3 5 7 9 11 13 15 BDBUS1 2 VDD_USB BDBUS0 2 Q403 BSS138N R416 10K VDD_USB 33 2 Q406 BSS138N 5 2 10K R419 Q404 BSS138N USR1_DAP USR1 TDI /TRST TCK TMS TDO /DBGRST USR2 Q405 BSS138N 33 Q402 BSS138N P3_1 P1_3 P1_14 P1_2 /ESR0_/HDRST /PORST /PORST 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 G G 6 GND +3V3 22R_opt 22R_opt R438 R437 22R_opt 22R_opt R436 22R_opt R435 0R_opt R434 R433 CB407 100n GND /PORST 1 3 5 7 9 6 /DBGRST /PORST DAI2 DAI1 GND DAI4 DAI3 /ESR0_/HDRST A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 ETK_CON_opt B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 X403 2 4 6 8 10 TDO VDDESB /DBGRST VDDP /TRST TMS TCK TDI 22R_opt R439 TMS TCK TDO USR1_DAP /DBGRST 3 of 8 Infineon Technologies AG JTAG.. 8 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\OCDS.sch Sheet: TriBoard LQFP176 miniWiggler, DAP and ETK DAP2WIRE VREF DAP1 GND DAP0 GND USER0_IO KEY USER1_IN GND RESET X402 /BRKOUT_ETK VDDESB USR1 /DBGRST USR2 1 TDO BAT54 D403 USR2 GND R422 opt 3 TCK TDI TMS /TRST 7 TDO GND R421 opt GND TCK TDI TMS USR0 /TRST /RESET USR1 USR8 /BRKIN_ETK /ESR0_/HDRST 0R R432 0R_opt R431 2 4 6 8 11 13 15 17 1 19 18 16 14 12 9 7 5 3 20 10 +3V3 ONLY WITH TC1767, TC178X AND TC1387 SN74AHCT244PW 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 VCC GND U404 PIN116 P1_1 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 VCC GND SN74AHC244PW 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 G G U403 R412 680R D402 LP T67K +3V3 P1_15 18 16 14 12 9 7 5 3 20 10 2 4 6 8 11 13 15 17 1 19 /ESR0_/HDRST R440 0R R420 1K +3V3 GND CB408 100n 2 R409 10K +3V3 R415 10K +3V3 VDD_USB 33 +3V3 Q401 BSS138N R417 10K +3V3 ACBUS3 ADBUS2 ADBUS0 ADBUS1 ADBUS3 ADBUS6 ACBUS0 ACBUS1 ACBUS2 ADBUS5 ADBUS4 2 R410 10K VDD_USB 5 1 CB403 3 1 GND PIN116 GND VDD_USB Y401 CSTCR6M00G 1K5 27R R404 27R R403 R402 GND GND VDD_USB GND GND 2 VDD_USB MMZ1608R300A L401 1 3 3 42 VCC VCC 46 AVCC 14 31 VCCIOA VCCIOB GND GND GND GND 9 18 25 34 AGND 45 1 1 1 1 User’s Manual P3_1 Figure 8-4 P3_0 1 A B C D TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - MiniWiggler, DAP and ETK V 2.1, 2009-06 A B 1 P2_13 165 TC176X/TC116X/TC178X/TC1387-LQFP176 P2.13 / IN13 / OUT3 / SLSI11 / SDI0 P5_15 0R 0R R525 2 3 P6.1 / IN15 / OUT5 / OUT81 / FCLP0A P6.0 / IN14 / OUT4 / OUT80 / FCLN0 P6.3 / IN25 / OUT7 / OUT83 / SOP0A P6.2 / IN24 / OUT6 / OUT82 / SON0 P2.8 / SLSO04 / SLSO14 / EN00 P2.9 / SLSO05 / SLSO15 / EN01 P5.8 / RDATA0B / OUT89 P5.9 / RVALID0B / OUT90 P5.10 / RREADY0B / OUT91 P5.11 / RCLK0B / OUT92 P5.12 / TDATA0 / SLSO07 / OUT93 P5.13 / TVALID0B / SLSO16 P5.14 / TREADY0B / OUT94 P5.15 / TCLK0 / OUT95 ONLY WITH TC1767, TC178X AND TC1387 R524 0R PIN9 R523 P1_0 C GPTA / LTCA / HWCFG / SSC / MLI / MSC 3 P0.0 / IN0 / HWCFG0 / OUT0 / OUT56 P1.8 / IN24 / IN48 / MTSR1B / OUT24 / OUT48 P0.1 / IN1 / HWCFG1 / OUT1 / OUT57 P1.9 / IN25 / IN49 / MRST1B / OUT25 / OUT49 P0.2 / IN2 / HWCFG2 / OUT2 / OUT58 P1.10 / IN26 / IN50 / OUT26 / OUT50 / SLSO17 P0.3 / IN3 / HWCFG3 / OUT3 / OUT59 P1.11 / IN27 / IN51 / SCLK1B / OUT27 / OUT51 P0.4 / IN4 / HWCFG4 / OUT4 / OUT60 P4.0 / IN28 / IN52 / OUT28 / OUT52 P0.5 / IN5 / HWCFG5 / OUT5 / OUT61 P4.1 / IN29 / IN53 / OUT29 / OUT53 P0.6 / IN6 / HWCFG6 / REQ2 / OUT6 / OUT62 P4.2 / IN30 / IN54 / OUT30 / OUT54 / EXTCLK1 P0.7 / IN7 / HWCFG7 / REQ3 / OUT7 / OUT63 P4.3 / IN31 / IN55 / OUT31 / OUT55 / EXTCLK0 P0.8 / IN8 / RXDA0 / OUT8 / OUT64 P2.0 / IN32 / OUT32 / OUT28 / TCLK0 P0.9 / IN9 / RXDB0 / OUT9 / OUT65P2.1 / IN33 / TREADY0A / OUT33 / SLSO03 / SLSO13 P0.10 / IN10 / OUT10 / TXDA0 P2.2 / IN34 / OUT34 / OUT29 / TVALID0A P0.11 / IN11 / OUT11 / TXDB0 P2.3 / IN35 / OUT35 / OUT30 / TDATA0 P0.12 / IN12 / OUT12 / TXENA P2.4 / IN36 / RCLK0A / OUT36 / OUT31 P0.13 / IN13 / OUT13 / TXENB P2.5 / IN37 / OUT37 / OUT110 / RREADY0A P0.14 / IN14 / REQ4 / OUT14 / OUT70 P2.6 / IN38 / RVALID0A / OUT38 / OUT111 P0.15 / IN15 / REQ5 / OUT15 / OUT71 P2.7 / IN39 / RDATA0A / OUT39 P1.0 / IN16 / OUT16 / OUT72 / BRKIN / BRKOUT P5.0 / IN26 / IN40 / OUT8 / OUT40 P1.1 / IN17 / OUT17 / OUT73 P5.1 / IN27 / IN41 / OUT9 / OUT41 P1.2 / IN18 / OUT18 / OUT74 P5.2 / IN28 / IN42 / OUT10 / OUT42 P1.3 / IN19 / OUT19 / OUT75 P5.3 / IN43 / OUT11 / OUT43 P1.4 / IN20 / EMGSTOP / OUT20 / OUT76 P5.4 / IN30 / IN44 / OUT12 / OUT44 P1.5 / IN21 / OUT21 / OUT77 P5.5 / IN31 / IN45 / OUT13 / OUT45 P1.6 / IN22 / OUT22 / OUT78 P5.6 / IN32 / IN46 / OUT14 / OUT46 P1.7 / IN23 / OUT23 / OUT79 P5.7 / IN47 / OUT15 / OUT47 U201D PIN116 145 146 147 148 166 167 173 174 149 150 151 152 168 169 175 176 116 119 93 98 107 108 109 110 P1_1 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 PIN116 PIN119 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 PIN119 D 2 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 P5_8 P5_9 P5_10 P5_11 P5_12 P5_13 P5_14 PIN9 P6_1 P6_0 P6_3 P6_2 P2_8 P2_9 94 95 96 97 86 87 88 90 74 75 76 77 78 79 80 81 1 2 3 4 5 6 7 8 13 14 15 16 17 18 19 9 157 156 159 158 164 160 4 PIN119 P5_7 P5_6 P5_5 P5_4 P5_3 P5_2 P5_1 P5_0 4 100R +3V3 AN[0..35] NOT WITH TC1767, TC178X AND TC1387 GND R522 1K R521 opt +3V3 LB T673 100R R518 D508LB T673 100R R515 D505LB T673 100R R517 100R R514 D504LB T673 100R R516 100R R513 D503LB T673 D507LB T673 0R 100R R512 D502LB T673 D506LB T673 R510 R511 D501 5 5 0R R531 ADC / FADC R533 0R R532 P9_5 GND +3V3 VDDP 6 27 26 51 52 25 24 23 53 54 73 72 71 R528 0R R526 0R R508 0R R529 0R NOT WITH TC1387 VFAGND +3V3 +5V VSSMF VDDMF +3V3 R505 0R VAGND0 0R 0R CB504 100n R507 VAREF0 VSSMF 0R R503 4 of 8 Infineon Technologies AG 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\GPTA_ADC.sch Sheet: PORT[0..10] VSSM VDDM GND NOT WITH TC1387 VDD R502 CB501 47n VDDAF NOT WITH TC1767, TC178X, TC1387 OR IF 3,3V ADC 0R R520 0R R519 GND 0R CB506 100n R509 VFAREF VSSMF 0R 8 ONLY WITH TC1767, TC178X, TC1387 OR IF 5V ADC R504 0R CB503 47n VDDMF VSSM CB502 R501 47n VDDM P1_12 P1_13 P1_14 7 TriBoard LQFP176 GPTA, MSC, MLI and ADC VSSMF VFAGND R530 0R R527 0R VDDAF VDDMF VFAREF TC176X/TC116X/TC178X/TC1387-LQFP176 AN0 P1.12 / IN16 / OUT16 / AD0EMUX0 AN1 P1.13 / IN17 / OUT17 / AD0EMUX1 AN2 P1.14 / IN18 / OUT18 / AD0EMUX2 AN3 AN4 AN5 AN6 VDDM AN7 AN8 AN9 VSSM AN10 AN11 AN12 AN13 VDDAF AN14 AN15 AN16 VDDMF AN17 AN18 AN19 VSSMF AN20 AN21 AN22 AN23 VAREF0 AN24 AN25 AN26 VAGND0 AN27 AN28 / FAIN2P AN29 / FAIN2N AN30 / FAIN3P VFAREF AN31 / FAIN3N AN32 / FAIN0P AN33 / FAIN0N VFAGND AN34 / FAIN1P AN35 / FAIN1N U201E 0R CB508 R534 47n 0R ONLY WITH TC1387 AN35 AN32 AN33 67 66 65 64 63 62 61 36 60 59 58 57 56 55 50 49 48 47 46 45 44 43 42 41 40 39 38 37 35 34 33 32 31 30 29 28 CB507 100n GND AN34 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 AN32 AN33 AN34 AN35 6 P9_0 P9_2 8-6 P9_1 User’s Manual P9_4 Figure 8-5 P9_3 1 A B C D TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - GPTA, MSC, MLI and ADC V 2.1, 2009-06 A B C D BC848C 1 /ESR1_/NMI SS12 C614 1µ/6V GND /ESR1_/NMI RESET R620 4K7 +3V3 R626 4K7 +3V3 GND 2 4K7 R621 D607 LP T67K GND R622 10K GND_A GND_P WDI EN_uC EN_IGN 1 C615 4µ7/10V GND BST SW SW 0R_opt R609 3 R623 0R RT RO_1 RO_2 WDO Q_T1 Q_T2 FB_EXT DRV_EXT Q_LDO2 Q_LDO1 FB/L_IN IN_LDO2 Q602 BC848C SEL_LDO2 CCP C2- C2+ C1- C1+ IN IN TLE7368G GND 1 18 23 10 11 22 GND GND_A 10K 10K R602 VIN 220n +3V3 R601 +3V3 R619 1K5 +5V 16 C602 100n 13 15 19 20 C603 100n 14 C604 17 CB601 100n VIN GND C601 47µ/50V S601 R625 1K +3V3 +3V3 GND D606 LP T67K R618 680R +3V3 /ESR0_/HDRST /PORST GND D605 LP T67K R617 620R +3V3 Q604 1 /PORST 82K R616 SS12 /ESR0_/HDRST VDD GND VDD D608 +3V3 D609 +5V GND GND C611 22µ/10V Q_STBY C613 4µ7/10V Q_T2 Q_T1 C612 4µ7/10V GND GND C610 22µ/10V +3V3 GND VDD X601 POWER VCC_IN D601 1X1 1 MBRS360T3 C609 22µ/10V +5V 5,5V..50V 2 2 3 2 WDI IN_STBY Q_STBY SEL_STBY MON_STBY /PORST 0R 1 GND 4K7_opt R640 C606 47µ/10V GND /PORST P1_15 P1_3 0R C607 4µ7/10V 0R_opt +3V3 R608 R606 Q601 BDP949 VSW VSW P1_2 4 VDD /ESR0_/HDRST R624 0R_opt R627 10K 1 GND D604 LS T67K R628 120R Q603 BC858C +3V3 4 PORT[0..10] 5 BST SHDN IN IN 7 8 9 10 GND /PORST LTC3026EM PG ADJ OUT OUT U603 +3V3 0R R610 GND GND VDDP GND GND 0R R630 ONLY WITH TC1767, TC178X AND TC1387 0R R634 GND NOT WITH TC1767, TC178X AND TC1387 P5_15 GND C618 4µ7/10V 5 6 1 2 10µH/150mA L602 GND GND 47n GND GND 0R 0R GND R632 R629 GND VDDCORE ONLY WITH TC1767 3 GND CB625 100n_opt VIN 5 IN U602 TLE4284DV_opt GND OUT 2 0R R637 GND 6 C616 10µ/10V_opt VDDESB 1 VDDCORE 0R 100n 100n 100n CB607 CB608 CB609 121 120 11 20 69 83 89 100 124 139 154 171 R612 0R POWER 0R R615 PIN92 122 141 GND GND /ESR0_/HDRST of 8 0R R614 Infineon Technologies AG +3V3 8 NOT WITH TC1767, TC178X AND TC1387 P1_1 R636 0R 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\Supply.sch 5 TriBoard LQFP176 Power supply Sheet: CB626 47n /ESR0_/HDRST CB610 47n VDDFL3 U201A TC176X/TC116X/TC178X/TC1387-LQFP176 ESR0 VDDFL3 GND NOTE: VDDCORE is +1,2V for TC178X VDDCORE is +1,5V for TC176X, TC116X and TC1387 CB604 100n CB603 100n ONLY WITH TC1767, TC178X AND TC1387 GND PORST ESR1 VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP 0R GND VDD VDDCORE R611 100n CB605 100n CB606 VDDP CB602 100n R633 0R ONLY WITH TC1767 R635 0R 7 R631 ONLY WITH TC178X AND TC1387 BAT54_opt VDD NOT WITH TC1767, TC178X AND TC1387 CB606 ONLY WITH TC1767, TC178X AND TC1387 3 0R D603 VDDESB CB624 R613 R637 ONLY WITH TC178X AND TC1387 R612 NOT WITH TC178X AND TC1387 GND 6 ONLY WITH TC1X6XED, TC1767, TC178X AND TC1387 ONLY WITH TC1X6XED, TC1767, TC178X, TC1387 AND ON REQUEST CB617 ONLY WITH TC1767, TC178X AND TC1387 /PORST /ESR0_/HDRST /ESR1_/NMI GND R644 4K02 C617 10µ/10V VDD R643 9K09 0R R642 ONLY WITH TC178X (IN THIS CASE R640 not assembled) P1_0 P1_1 CB613 ONLY WITH TC1767, TC178X AND TC1387 NOTE: VDD is +1,5V for TC176X, TC116X and TC1387 VDD can be +1,2V for TC178X (R643 is 8K06) OR VDD can be +1,3V for TC178X (R643 is 9K09) R641 0R 0R R607 R605 10K +3V3 GND /PORST C608 1n2 24 WDO RO_5V 3 4 2 GND +5V L601 47µ/3A D602 MBRS340T3 0R +3V3 R639 R638 C605 680n 0R_opt R603 10K R604 +3V3 Q_T1 8 Q_T2 9 30 31 7 29 28 6 27 25 26 34 36 3 2 Q_STBY /PORST 4 SW GND 3 U601 3 /ESR1_/NMI 35 12 3 2 21 170 VDD / VDDSB VDD / VDDSB 2 ADJ / GND /ESR0_/HDRST ONLY WITH TC178X AND TC1387 CB612 100n CB613 100n CB614 100n CB615 100n CB617 100n CB619 100n CB620 100n CB621 100n CB622 100n CB629 100n 1 2 3 /PORST P1_0 PIN91 10 68 84 91 99 123 153 VDD VDD VDD VDD VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS 8-7 12 22 70 82 85 92 101 125 140 155 172 User’s Manual PIN92 Figure 8-6 PIN92 1 A B C D TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - Power Supply V 2.1, 2009-06 Figure 8-7 User’s Manual 8-8 A B C D NC1[1..80] 1 PORT[0..9] NC3[1..80] ADC BUS EXPANSION 1 2 P1_12 P1_13 P1_14 NC3_77 P0_15 +3V3 VSSM NC3_63 NC3_65 NC3_67 +3V3 VSSM VSSM 3 NC3_72 NC3_74 NC3_76 P0_14 NC3_80 NC3_64 NC3_66 NC3_68 3 NC3_46 NC3_50 NC3_52 NC3_54 NC3_56 NC3_58 NC3_60 VSSMF VDDMF VFAREF VAGND0 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM NC1_6 NC1_8 NC1_10 NC1_12 NC1_14 NC1_16 NC1_18 NC1_20 NC1_22 NC1_24 NC1_26 NC1_28 NC1_30 NC1_32 NC1_34 NC1_36 NC1_38 NC1_40 NC1_42 NC1_44 NC1_46 NC1_48 NC1_50 NC1_52 NC1_54 NC1_56 NC1_58 NC1_60 NC1_62 NC1_64 NC1_66 NC1_68 NC1_70 NC1_72 NC1_74 NC1_76 NC1_78 NC1_80 GND FTSH-140-02-L-DV-ES-A X703 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FTSH-140-02-L-DV-ES-A_opt X701 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 NOT ASSEMBLED VSSM VDDM VFAGND VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 NC3_57 NC3_59 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 NC1_5 NC1_7 NC1_9 NC1_11 NC1_13 NC1_15 NC1_17 NC1_19 NC1_21 NC1_23 NC1_25 NC1_27 NC1_29 NC1_31 NC1_33 NC1_35 NC1_37 NC1_39 NC1_41 NC1_43 NC1_45 NC1_47 NC1_49 NC1_51 NC1_53 NC1_55 NC1_57 NC1_59 NC1_61 NC1_63 NC1_65 NC1_67 NC1_69 NC1_71 NC1_73 NC1_75 NC1_77 NC1_79 2 AN[0..35] 4 4 XTAL[1..2] /ESR1_/NMI 5 5 GND +3V3 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P5_11 P5_10 P5_9 P5_8 +3V3 VDDESB XTAL1 XTAL2 P3_0 P3_1 P3_12 P3_13 P3_2 P3_4 P3_3 P9_0 P3_10 P0_6 GND NC2_21 NC2_23 P2_8 P2_13 P6_1 P6_0 P6_3 P6_2 NC2_37 NC2_39 P3_5 P3_7 P2_8 P3_8 NC2_9 NC2_11 P0_5 /ESR1_/NMI NC2_17 VCC_IN 6 +3V3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 NC4_38 NC4_40 P9_2 P9_3 P9_4 P9_5 NC4_50 NC4_52 NC4_54 NC4_56 P1_4 NC4_60 NC4_62 NC4_64 NC4_66 NC4_68 P5_12 P5_13 P5_14 P5_15 GND FTSH-140-02-L-DV-ES-A X704 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4_3 NC2_54 P3_9 P3_8 P3_14 P3_15 P2_11 P2_12 P2_10 P9_1 P3_11 P0_7 /PORST NC2_24 P2_9 NC2_28 NC2_30 NC2_32 NC2_34 NC2_36 NC2_38 P2_13 P3_6 P2_1 P2_9 P1_10 +3V3 GND GND GND NC2_10 NC2_12 NC2_14 /ESR0_/HDRST NC2_18 VCC_IN GND FTSH-140-02-L-DV-ES-A X702 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 6 GPTA / MLI 6 of 8 Infineon Technologies AG 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\Connectm.sch Sheet: 8 TOP PERIPHERALS TriBoard LQFP176 Connectors plug NC4[1..80] /PORST /ESR0_/HDRST NC2[1..80] 7 A B C D TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - Connectors (Plug) V 2.1, 2009-06 Figure 8-8 User’s Manual 8-9 A B C D NC1[1..80] 1 PORT[0..9] NC3[1..80] ADC BUS EXPANSION 1 2 P1_12 P1_13 P1_14 NC3_77 P0_15 +3V3 VSSM NC3_63 NC3_65 NC3_67 FLE-140-01-G-DV-A X803 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FLE-140-01-G-DV-A_opt X801 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 NOT ASSEMBLED VSSM VDDM VFAGND VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 NC3_57 NC3_59 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 NC1_5 NC1_7 NC1_9 NC1_11 NC1_13 NC1_15 NC1_17 NC1_19 NC1_21 NC1_23 NC1_25 NC1_27 NC1_29 NC1_31 NC1_33 NC1_35 NC1_37 NC1_39 NC1_41 NC1_43 NC1_45 NC1_47 NC1_49 NC1_51 NC1_53 NC1_55 NC1_57 NC1_59 NC1_61 NC1_63 NC1_65 NC1_67 NC1_69 NC1_71 NC1_73 NC1_75 NC1_77 NC1_79 2 +3V3 VSSM VSSM NC3_72 NC3_74 NC3_76 P0_14 NC3_80 NC3_64 NC3_66 NC3_68 3 NC3_46 NC3_50 NC3_52 NC3_54 NC3_56 NC3_58 NC3_60 VSSMF VDDMF VFAREF VAGND0 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM NC1_6 NC1_8 NC1_10 NC1_12 NC1_14 NC1_16 NC1_18 NC1_20 NC1_22 NC1_24 NC1_26 NC1_28 NC1_30 NC1_32 NC1_34 NC1_36 NC1_38 NC1_40 NC1_42 NC1_44 NC1_46 NC1_48 NC1_50 NC1_52 NC1_54 NC1_56 NC1_58 NC1_60 NC1_62 NC1_64 NC1_66 NC1_68 NC1_70 NC1_72 NC1_74 NC1_76 NC1_78 NC1_80 GND 3 AN[0..35] 4 4 XTAL[1..2] /ESR1_/NMI 5 5 GND +3V3 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P5_11 P5_10 P5_9 P5_8 +3V3 VDDESB XTAL1 XTAL2 P3_0 P3_1 P3_12 P3_13 P3_2 P3_4 P3_3 P9_0 P3_10 P0_6 GND NC2_21 NC2_23 P2_8 P2_13 P6_1 P6_0 P6_3 P6_2 NC2_37 NC2_39 P3_5 P3_7 P2_8 P3_8 NC2_9 NC2_11 P0_5 /ESR1_/NMI NC2_17 VCC_IN FLE-140-01-G-DV-A X804 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FLE-140-01-G-DV-A X802 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4_3 NC2_54 P3_9 P3_8 P3_14 P3_15 P2_11 P2_12 P2_10 P9_1 P3_11 P0_7 /PORST NC2_24 P2_9 NC2_28 NC2_30 NC2_32 NC2_34 NC2_36 NC2_38 P2_13 P3_6 P2_1 P2_9 P1_10 6 +3V3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 NC4_38 NC4_40 P9_2 P9_3 P9_4 P9_5 NC4_50 NC4_52 NC4_54 NC4_56 P1_4 NC4_60 NC4_62 NC4_64 NC4_66 NC4_68 P5_12 P5_13 P5_14 P5_15 GND +3V3 GND GND GND NC2_10 NC2_12 NC2_14 /ESR0_/HDRST NC2_18 VCC_IN GND 6 GPTA / MLI PERIPHERALS 7 of 8 Infineon Technologies AG 7 8 AIM MC ACE PDA Number: Am Campeon 1-12 D-85579 Neubiberg Revision: 2.1 Date: 26-Jun-2009 Tel.: +49-89-234-0 File: G:\Technical_Support\TriCore\TriBoard\EDA\TriBoard TC176X TC116X TC178X TC1387\TriBoard TC176X TC116X TC178X TC1387.ddb - TriBoard LQFP176 V2.1\Connectf.sch Sheet: 8 BOTTOM TriBoard LQFP176 Connectors socket NC4[1..80] /PORST /ESR0_/HDRST NC2[1..80] 7 A B C D TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Schematic - Connectors (Socket) V 2.1, 2009-06 L401 X402 R318 R401 C401 R327 R324 CB313 R368 CB310 R310 C304 R371 C601 1 X401 D402 R326 CB315 R325 CB311 R311 R369 CB312 R323 R370 R321 R332 C611 C607 R405 R406 U402 R307 R404 1 R432 R309 D403 R431 D604 X403 R434 D501 R602 X704 D507 D506 D505 D504 X703 XT201 U201 R515 R516 R517 R513 R514 D503 R641 R608 C610 R601 R501 D605 R639 R607 R209 D606 D607 R379 R372 R439 R210 R433 D502 R511 CB401 R317 D508 R510 R407 R408 R366 R512 CB203 1 2 3 4 5 6 7 8 R518 1 1 CB207 R231 JP203 CB209 C208 U204 R230 X701 R227 R356 U306 R355 R229 X702 CB204 U202 CB208 R354 R353 CB319 X203 X202 D201 R233 CB406 C303 R316 CB404 CB402 D401 CB316 R314 R330 R308 R315 R329 T302 R328 R331 P301 P302 X601 X201 T301 R367 CB309 L601 D203 JP202 R402 R403 U203 R313 U302 U303 R640 CB314 CB601 R603 R312 S601 U601 R621 C602 C604 C608 R322 R622 X301 X302 C603 C207 D202 R234 R228 8-10 R235 D204 JP201 User’s Manual S202 R213 R249 R245 Figure 8-9 R242 8.2 R237 P401 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Layout Component Plot Top Layer V 2.1, 2009-06 D205 S201 R236 R238 R241 R243 R244 R246 R248 R247 R251 C211 R240 C209 C210 C205 R253 R256 R258 R257 Y202 R255 CB206 X802 R252 R521 R211 CB603 R225 1 R635 C201 CB621 R615 R636 CB606 CB617 C202 R208 R620 R232 R614 CB609 CB201 C616 CB612 R364 R304 R221 R218 R613 R612 R532 CB604 R637 CB508 R378 R377 R206 R357 R204 R373 CB607 R519 R520 R507 CB504 X803 C617 R643 R644 R504 R502 R503 CB624 CB613 CB501 R363 R306 R374 R375 R365 R626 R202 R362 R319 R320 R361 R305 R333 R425 R426 R201 R415 R409 R420 C618 R617 R619 R345 R618 R642 R347 R342 R438 R437 R625 R336 R419 R417 R427 CB407 R428 R421 U403 R436 R422 R604 R616 CB408 R435 R416 L302 R360 R346 R359 R348 1 Q603 R627 R624 R623 Q602 CB305 R351 CB302 R349 R350 R352 R424 R414 R410 R606 R628 R609 1 Y301 CB306 L301 C301 R411 R429 D609 D602 C605 D608 R301 CB403 Y401 CB409 R430 CB405 U401 X804 R524 R376 CB619 R527 R533 R534 CB507 CB502 R526 R203 R215 R250 CB205 R254 C212 C206 R522 R525 R226 CB615 Y201 R631 R224 R629 R207 R212 CB625 R223 CB622 CB202 U602 R633 R611 R632 R610 R222 CB626 R220 R217 CB602 CB610 D603 R219 R216 CB614 CB629 CB608 R531 R530 C203 CB620 R634 R205 R523 R508 R529 R528 CB506 R412 R423 1 L602 C204 R509 CB503 R630 R440 R337 CB317 R343 Q604 R358 CB605 R505 R339 U603 U304 U305 R334 R344 C613 CB318 Q406 Q404 Q402 Q405 Q403 Q401 R338 C612 CB307 R418 R341 C615 R335 R340 C302 R638 R302 U404 CB308 R303 R605 C614 U301 CB304 C609 8-11 D601 Q601 CB301 CB303 User’s Manual C606 X801 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Figure 8-10 Component Plot Bottom Layer V 2.1, 2009-06 R239 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout 8.3 Layout with Dimensioning The following dimensions should be used for development of extension boards. Note: these are the pictures from the TriBoard TC10GP. Connectors X801...X804 are on the same place. Figure 8-11 Dimensioning (mil) User’s Manual 8-12 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Schematic and Layout Figure 8-12 Dimensioning (mm) User’s Manual 8-13 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual Keyword Index Numerics I P4 4-2 P0 4-2 Interrupt Signals 6-2 A Layout 8-10 LEDs 3-1 Location of general optional resistors on Bottom Side 4-5 Location of general optional resistors on Top Side 4-5 Location of peripheral resistors on Bottom Side 4-7 Location of peripheral resistors on Top Side 4-7 Location of resistors for safety device on Bottom Side 4-8 ACTIV LED 3-2 Assembly Options 4-4 C CAN connector pinout 7-5 Clock 3-1 Clock Signals 6-2 Connector for TC176X/TC116X/TC1782/TC13 87 7-2 Connector Pin Assignment 7-1 CPU clock 3-1 Crystal oscillator 3-1 D DAP 3-5 DAP connector pinout 7-5 Debug Signals 6-2 Debug System 3-4 Dimensioning 8-12 E External clock 3-1 F Flexray Pinout 7-4 G General optional resistors 4-4 H HW Boot Configuration 4-1 HW Boot Configuration all other TC176X / TC116X 4-2 HWCFG 4-1 User’s Manual L M manual reset 3-1 MiniWiggler 3-2 MultiCAN 3-3 O OCDS connector pinout 7-5 OCDS1 3-4 oscillator circuit 3-1 Other peripherals 3-4 P Peripheral Signals 6-2 Power connector pinout 7-4 Power Signals 6-1 power supply 3-1 R reset 3-1 Reset Signals 6-1 Resistors for peripherals 4-6 Resistors for safety device 4-8 Robinson Nugent 7-1 L-1 V 2.1, 2009-06 TriBoard TC176X/TC116X/TC1782/TC1387 Hardware Manual RUN LED 3-2 S Safety device Signals 6-4 Safety option 3-4 Samtec 7-1 Schematic 8-1 Schematic and Layout 8-1 Serial Connection to PC 3-2 Serial EEPROM 3-3 Serial Eeprom 3-3 Signal Description 6-1 Software 5-1 status LED 3-4 Supply 3-1 T Toggle LED’s 3-4 TriBoard LQFP176 V2.1 Placement 2-4 TriBoard Software 5-1 Type of Boot TC1767, TC1782 and TC1387 4-1 Type of Boot TC176X / TC116X 4-2 U USB Connector 3-2 USB connector pinout 7-4 User’s Manual L-2 V 2.1, 2009-06 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG