32-Bit Microcontroller TriBoard TC1728 Hardware: TriBoard-TC1728 V1.0 Hardware Manual User’s Manual V 1.0 2011-02 Microcontrollers Edition 2011-02 Published by Infineon Technologies AG 81726 Munich, Germany © 2011 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 32-Bit Microcontroller TriBoard TC1728 Hardware: TriBoard-TC1728 V1.0 User’s Manual V 1.0 2011-02 Microcontrollers TriBoard TC1728 Hardware Manual TriBoard TC1728 User’s Manual Revision History: V 1.0 2011-02 Previous Versions: no Page Subjects (major changes since last revision) – this is the first release – – Trademarks TriCore® is a trademark of Infineon Technologies AG. We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] User’s Manual V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 2 2.1 2.2 2.3 TriBoard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2-1 2-3 2-4 3 3.1 3.2 3.3 3.4 3.4.1 3.4.2 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.11.1 3.11.2 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FlexRay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety option with SAK-CIC61508 (optional) . . . . . . . . . . . . . . . . . . . . . . Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3-1 3-1 3-1 3-2 3-2 3-2 3-3 3-3 3-3 3-3 3-3 3-4 3-4 3-4 3-4 4 4.1 4.2 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 HW Boot Configuration TC1728 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 5 5.1 5.2 5.3 TriBoard Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TC1728 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flexray Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User’s Manual L-1 5-1 5-1 5-1 5-1 7-1 7-2 7-4 7-4 7-4 7-5 7-5 7-5 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual 8 8.1 8.2 8.3 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 User’s Manual L-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual List of Figures Figure 2-1 Figure 2-2 Figure 3-1 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 7-1 Figure 7-2 Figure 7-3 Figure 7-4 Figure 7-5 Figure 7-6 Figure 7-7 Figure 7-8 Figure 8-1 Figure 8-2 Figure 8-3 Figure 8-4 Figure 8-5 Figure 8-6 Figure 8-7 Figure 8-8 Figure 8-9 Figure 8-10 Figure 8-11 Figure 8-12 User’s Manual TriBoard Block Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 TriBoard TC1728 V1.0 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Clock socket usage (XT301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 HW Configuration TC1728 DIP-Switch . . . . . . . . . . . . . . . . . . . . . . . 4-1 Location of general optional resistors on Top Side . . . . . . . . . . . . . . 4-4 Location of general optional resistors on Bottom Side. . . . . . . . . . . . 4-4 Location of peripheral resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-5 Location of peripheral resistors on Bottom Side . . . . . . . . . . . . . . . . 4-6 Location of resistors for safety device on Bottom Side . . . . . . . . . . . 4-7 Connector for TC1728 - Pinout (Part I, Top View) . . . . . . . . . . . . . . . 7-2 Connector for TC1728 - Pinout (Part II, Top View) . . . . . . . . . . . . . . 7-3 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Flexray Pinout (SUBD-9 Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 DAP connector pinout (FTSH10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Schematic - Config, Clock, JTAG and CIC61508 . . . . . . . . . . . . . . . 8-3 Schematic - Flexray, CAN and Eeprom . . . . . . . . . . . . . . . . . . . . . . . 8-4 Schematic - miniWiggler JDS, DAP and ETK . . . . . . . . . . . . . . . . . . 8-5 Schematic - GPTA, MSC, MLI and ADC . . . . . . . . . . . . . . . . . . . . . . 8-6 Schematic - Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Schematic - Connectors (Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Schematic - Connectors (Socket) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Component Plot Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 L-3 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual User’s Manual L-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual List of Tables Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 6-1 Table 6-2 Table 6-3 Table 6-4 Table 6-5 Table 6-6 Table 6-7 User’s Manual User Startup Modes for TC1728 . . . . . . . . . . . . . . . . . . . . . . . . . . . . General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistors for safety device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety device Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L-5 4-1 4-3 4-5 4-6 6-1 6-1 6-1 6-2 6-2 6-2 6-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual User’s Manual L-6 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual User’s Manual -7 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Introduction 1 Introduction We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quick access to the capabilities of TriCore's powerful architecture. Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features (OCDS1 and DAP). The kit also includes several sets of development tools, which are stored on the included Evaluation Board CD-ROM. The Evaluation Board allows easily the development of TriCore applications with the corresponding tools. Subsequently, the applications can be downloaded and can be tested with the powerful debugger software. This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the initial configuration of the TriBoard. For detailed technical information about the TC1728 please refer to the User Manual of the device. User’s Manual 1-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Introduction User’s Manual 1-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Features 2 TriBoard Features 2.1 Summary of Features – – – – – – – – – – – Infineon’s TC1728 Controller in LQFP176 Package FlexRay Transceivers Safety device (optional) High Speed CAN Transceivers USB to UART bridge Crystal 20MHz (default), Oscillator or External Clock USB miniWiggler JDS for easy debugging 8 Low Power Status LEDs 8-DIP switches for configuration access to all pins of controller 100mm x 160mm (EURO-Board) Connectors The TC1728 TriBoard offers a wide variety of connectors: – – – – – – – – Standard power connector USB connector for ASC Interface (ASC0) and miniWiggler 16-pin header for JTAG interface (OCDS) 10-pin header for DAP 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1) 2 x SUB-D9 Plug connector for FlexRay four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals optional ETK connector Components – – – – – – – – – – – – – Infineon’s Next generation micro controller supply TLE 7368-3E Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,3 Volt) LED indicating /HDRST (ESR0) active state LED indicating activ miniWiggler JDS LED switched via DAS software 2x FlexRay Transceiver AS8221(AMS) or TJA1080 (NXP) 2 x Infineon’s High Speed CAN-Transceiver TLE 6250 GV33 Infineon’s Safety Device SAK-CIC61508 (optional) USB to UART bridge FT2232HL (FTDI) SPI eeprom (Atmel) 8 general purpose LEDs Reset switch 8-pin Dip switch Zero Ohm Bridges User’s Manual 2-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Features Zero Ohm resistors give the flexibility to configure the systems functionality User’s Manual 2-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Features 2.2 Block Diagram XTAL CAN0 TxCAN0 PLL RxCAN0 CAN1 Transceiver TxCAN1 RxCAN1 OCDS1 USB B-TYPE USB miniWiggler TXD0 TC1728 TriCore CPU ERAY A 8 LED’s (P5.0 up to P5.7) Serial EEPROM Safety Device SAK-CIC61508 optional POWER SUPPLY WITH SUPERSONIC TLE7368-3E ERAY B FlexRay Transceiver SLSO00 SSC0 RXD0 Figure 2-1 User’s Manual TriBoard Block Schematic 2-3 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Features 2.3 Placement USB S201 X202 SEND P302 RST JP201 SENC R242 JP203 +3V3 JP202 SENB R237 U201 +5V U202 X201 S601 CAN1 RST X302 1 1 TriBoard-TC1728 V1.0 1 ERAY-B 1 X301 L1 CAN0 R245 1 P301 R249 1 ETK RUN X402 1 2 3 4 5 6 7 8 XT201 VDDP_CIC X203 1 DAP BOOTCONFIG X401 SYSDISC 1 ERAY-A SYSDISB P5.0 P5.1 P5.2 P5.3 P5.4 P5.5 P5.6 P5.7 A1 X403 ACT SYSDISA X701 1 1 1 OCDS1_CIC P401 X704 1 1 1 RST_CIC +1V3 SENA S202 U601 X601 POWER RESET_CIC X703 +5,5V...+50V(+40V) Figure 2-2 User’s Manual X702 1 1 1 1 TriBoard TC1728 V1.0 Placement 2-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Information 3 TriBoard Information 3.1 Power Supply The Board has to be connected to a +5,5V to +50V (+40V) DC power supply. The TriBoard generates internally +3.3V, +1V3 and +5V. The power consumption is not specified yet but a supply with 6V and 500mA should be sufficient. The pinout for the supply connector is shown in Figure 7-3. There can be used any standard power pack with a connector where the positive line is surrounded by the ground line. Maximum power supply is reduced to +40V if the SAK-CIC61508 option is assembled . Applying a stable supply voltage causes the power on reset after a short period. The three LED's (+5V, +3.3V, +1V3) indicate the status of the on board generated voltage. A manual reset is executed by pressing the reset button. 3.2 LEDs There are 14 or 19 LEDs on board: – – – – – – – – – – – – 3.3 D501 up to D508 (blue) -> toogle LEDs connected to P5.0 ... P5.7 D604 RST (red) -> RESET LED indicate the reset state of the board D505 +1V3 (green) -> +1,3V power supply indication D606 +3V3 (green) -> +3,3V power supply indication D607 +5V (green) -> +5V power supply indication D402 ACT (green) -> on board miniWiggler JDS is ACTIV D401 RUN (blue) -> Debug RUN mode (switched by DAS Server) D204 RST_CIC (red)-> RESET LED indicate that the CIC is in reset D205 +VDDP_CIC (green)-> +VDDP for CIC power supply indication (+3,3V) D201 SYSDISA (red)-> System Disable A (switched by CIC) D202 SYSDISB (red)-> System Disable B (switched by CIC) D203 SYSDISC (red)-> System Disable C (switched by CIC) Clock There are three possibilities to apply the CPU clock. • • • • Large oscillator circuit (DIP14) Small oscillator circuit (DIP8) Crystal oscillator (default with 20MHz) External clock generator User’s Manual 3-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Information The crystal oscillator and the oscillator circuit use the socket XT201. It's possible to apply a 14pol DIP oscillator package or an 8pol DIP oscillator package. OSCILLATOR OSCILLATOR XTAL DIP14 DIP8 Figure 3-1 3.4 GND External Clock Input Clock socket usage (XT301) USB Connector The USB connector is used for connection to a PC. Via the USB it is possible to using the ASC0 as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 7-4. NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. For actual DAS software please contact your local FAE. The software can also be found on the DAS website 3.4.1 Serial Connection to PC After the first connection of USB to a PC the needed driver will be installed automatically. During this there will be created a new COM port on PC. This COM port can be used to communicate with the board via ASC0 of the device (e.g. bootstrap loader). 3.4.2 miniWiggler JDS The miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of the device. Make sure that you have the latest DAS release. Debugging is possible via the DAS Server ‘UDAS‘. Please contact your prefered debug vendor for support of DAS. If you have connected the board to the PC and there runs the DAS server, then a working connection is visible via the green ACTIV LED. The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client). IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if the ACTIV LED is on. User’s Manual 3-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Information 3.5 FlexRay The board has 2 SUB-D connectors for FlexRay Communication with up to 10 Mbit/s. For the pinout of the plugs see Figure 7-5. The transceiver are connected directly to the TriCore device. For more information look in the user manual for TC1728. 3.6 Serial Eeprom The SSC0 of the TC1728 is connected to a serial EEPROM with a size of 128K (16.384 x 8). As chip select for this EEPROM is used the line SLSO00 (P3.5). To disconnect (disable) the EEPROM remove resistor R353. 3.7 MultiCAN On the board are two CAN transceiver connected to the MultiCAN on TC1728 node 0 and 1. The transceivers are connected to two IDC10 plug. For the pinout of IDC10 plug see Figure 7-6. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9. 3.8 Safety option with SAK-CIC61508 (optional) The safety device is only assembled if the board is with TC1728 or with the safety option. The SAK-CIC61508 is connected to the SSC0 of the microcontroller and use the line SLSO01 (P3.6) as chip select. There are 4 LED’s for indication the state of the safety device (SYSDISA, SYSDISB, SYSDISC, VDDP_CIC). On this board exists 4 potentiometer to stimulare the sense inputs of the safety device. Sensor inputs A and B can be connect to a potentiometer (JP201, JP202 , pos. 2-3) or to the core voltage of the microcontroller (JP201, pos. 1-2) for input A or to the port voltage of the microcontroller (JP202, pos. 1-2) for input B. With switch S202 it is possible to reset the safety device. If JP203 is set, then with S202 is also reset the microcontroller and the safety device is reset by a power on reset of the microcontroller. The safety device can be reprogrammed via JTAG and X203. 3.9 Other peripherals For all other peripherals there are no special plugs on the board. The peripheral signals are available on the different connectors. See “Connector Pin Assignment” on Page 7-1. Note: - SLSO00 is used as chip select for the serial eeprom on board. User’s Manual 3-3 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Information 3.10 Toggle LED’s Port 5pin 0 up to pin 7 are connected to single LED’s (D501... D508) and can be controlled by Software. This status LED’s are low active. 3.11 Debug System 3.11.1 OCDS1 The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of +3.3V. For pinout of the connector see Figure 7-7. You can connect any debugger to this connector. The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector then assemble R425 and R424 with a 0R resistor. If you connect a debug hardware make sure that the miniWiggler JDS (see “miniWiggler JDS” on Page 3-2) is not activ (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is tristated. If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC. 3.11.2 DAP The board comes with a DAP connector (X402). For pinout of this connector see Figure 7-8. You can connect a DAP hardware here. If you use this connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off) and a connected OCDS1 hardware is disconnected or tristated. User’s Manual 3-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual LOW HIGH 1 Figure 4-1 7 P0 . 6 P0 . .4 P0 P0 P0 P0 0 P0 . P0 HW Boot Configuration TC1728 .3 4.1 .2 TriBoard Configuration .1 4 .5 TriBoard Configuration on 2 3 4 5 6 7 8 HW Configuration TC1728 DIP-Switch The picture above shows the definition of the boot HW configuration switch. The meaning of the switches will be described in the following table (Table 4-1). Note: The ON position of the switch is equal to a logical LOW at the dedicated pin. Table 4-1 User Startup Modes for TC1728 Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch numbers HWCFG[7...0] Type of Boot TC1728 1 2 3 4 5 6 7 8 11XXXXXX Internal Start from Flash X X X X X X O O F F F F 01XXXXXX Generic (CAN/ASC auto detected) Bootstrap Loader - P3[13:12] X X X X X X O O F N F 10XXXXXX Alternate Boot Mode, Generic Bootloader on fail - P3[13:12] X X X X X X O O N F F 00XX10XX ASC Bootstrap Loader - P3[1:0] X X O O X X O O N F N N F User’s Manual 4-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration Table 4-1 User Startup Modes for TC1728 Note: The shadowed line indicates the default setting. Note: ’x’ represents the don’t care state. Note: 1 to 8 are the Dip Switch numbers HWCFG[7...0] Type of Boot TC1728 1 2 3 4 5 6 7 8 00XX11XX Alternate Boot Mode, ASC Bootloader on fail - X X O O X X O O P3[1:0] F F N N F F all others reserved; don’t use this combination User’s Manual 4-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration 4.2 Assembly Options Table 4-2 General optional resistors Component Description R205 XTAL Rserial (default: assembled) R206 XTAL Rparallel (default: not assembled) R423 Connect /BRKOUT with miniWiggler JDS (default: not assembled) R424 Connect /BRKOUT with OCDS1 connector (default: not assembled) R427 Connect /BRKIN with USR1 of miniWiggler JDS (default: not assembled R429 Connect /BRKIN with USR1 of DAP (default: not assembled R425 Connect /BRKIN with OCDS1 connector(default: not assembled) R428 Connect /TESTMODE with USR1 of miniWiggler JDS (default: not assembled R430 Connect /TESTMODE with USR1 of DAP (default: not assembled R426 Connect /TESTMODE with OCDS1 connector(default: not assembled) R432 Connect debug reset with /PORST(default: assembled) R431 Connect debug reset with /HDRST (default:not assembled) R510 Connect +3,3V to all toggle LEDs (default: assembled) R623 Connect reset switch with /PORST(default: assembled) R624 Connect reset switch with /HDRST (default:not assembled) R604 Connect P1.10 with MONSTBY of power device (default: not assembled) R606 Connect P1.3 with WDO of power device (default: not assembled) R609 Connect P1.15 with WDI of power device (default: not assembled) User’s Manual 4-3 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration Note: All resistors are red marked in the following figures P401 L601 C608 R603 R640 X601 D205 R249 R355 JP203 D605 CB319 R601 R245 R242 R237 X201 D606 R228 C603 C602 C604 CB601 R229 U601 D203 R227 D607 D204 U306 C610 R353 S202 R356 R354 R607 R602 X703 Figure 4-2 R235 JP202 CB208 D604 X702 1 C601 D202 CB614 R641 C611 R234 R233 X202 S201 R510 CB209 X302 R622 S601 U202 CB610 R639 C607 D201 X203 D508 D507 D506 D505 D504 D503 D501 R308 R615 R322 R312 CB314 R329 T302 R328 R331 R330 P302 R332 CB204 C208 R431 CB315 R325 C304 X301 R432 R326 R371 U204 CB207 R621 CB309 R307 R446 R213 R231 R230 JP201 R313 R366 R367 R309 U302 CB316 R327 R452 U201 CB311 R311 R369 CB312 R323 R370 R321 U303 CB310 D502 R372 R310 R368 1 2 3 4 5 6 7 8 XT201 R453 R209 U203 C303 D401 R411 R316 R317 R439 R515 R516 R517 R513 R514 R379 R429 R324 CB313 R518 R434 R433 R430 R315 T301 R314 P301 X403 X401 R450 X402 D403 D402 R413 R454 R511 CB203 R512 C402 CB405 R404 R318 X701 1 C207 C401 C403 L401 X704 1 CB413 L402 R401 CB401 U405 1 Location of general optional resistors on Top Side R403 X804 CB402 CB403 CB417 CB415 R644 R643 L602 C617 R623 R624 D608 Q603 R627 D602 C605 R605 D609 C606 R341 C615 C618 U603 R642 R616 R617 CB414 R444 CB418 C614 R638 R501 R456 Q602 C613 R519 CB406 R407 R451 CB419 R606 R628 R604 R441 R406 R455 R377 R609 R442 U406 R427 R445 R423 R507 R520 CB408 R414 R428 CB411 CB404 U404 CB416 R443 U402 U407 U408 R418 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 R424 R335 U304 CB318 R373 R612 CB504 R416 C612 R505 R610 U602 R618 C406 R410 X803 1 User’s Manual R339 R619 Q605 CB409 Q601 R620 X802 Figure 4-3 R614 C404 CB412 R405 U401 D603 CB611 R611 C621 C616 C619 R254 R253 R236 CB502 R438 R342 R319 C620 CB607 CB613 CB604 R255 R256 CB602 CB608 C201 R437 R320 Q604 R257 R258 R238 CB605 R608 R207 CB603 R305 R378 R336 U305 CB615 CB206 C205 R259 CB606 CB612 C202 Y201 R241 C206 R243 R333 R375 R252 Y202 CB205 R239 R240 R419 R625 R306 R376 R374 CB609 C212 R247 R244 R425 R344 R426 R626 R402 CB410 R340 R440 R202 R246 R417 R337 R201 C210 C209 CB317 R206 U403 R343 C203 C204 R448 R447 CB407 R415 R409 R420 R205 R203 C211 R204 R219 R221 R220 R224 R222 R251 R223 R250 R225 R226 R232 R412 R421 R449 R435 R436 R422 R248 C405 1 Y401 1 C609 X801 1 D601 Location of general optional resistors on Bottom Side 4-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration Table 4-3 Resistors for peripherals Component Description R333 Connect P3.12 with RXD of CAN0 transceiver (default: assembled) R339 Connect P3.14 with RXD of CAN1 transceiver (default: assembled) R353 Connect P3.5 (SLSO00) with /CS of Eeprom (default: assembled) R440 Connect P3.0 with TXD of USB to UART (default: assembled) R505 Connect VAREF0 with VDDM (default: assembled) R507 Connect VAGND0 with VSSM (default: assembled) R519 Connect +5V with VDDM (default: assembled) R520 Connect +3,3V with VDDM (default: not assembled) Note: All resistors are red marked in the following figures P401 Figure 4-4 User’s Manual U601 C608 R603 D205 D203 R235 D202 R249 R242 JP202 CB319 R601 R639 X201 R355 JP203 D605 R228 C603 C602 C604 CB601 R229 D606 R237 R622 S601 R227 D607 D204 U306 C610 R353 R354 R607 R356 S202 R602 X703 C601 R234 R233 X202 S201 R510 X302 CB209 CB208 D604 R640 X601 C611 U202 CB614 R641 C607 D201 X203 D508 D507 D506 D505 D504 D503 D501 R308 R322 R312 CB314 R329 T302 R328 R331 R330 R332 R615 CB610 L601 P302 C304 C208 R431 CB315 R325 CB204 CB207 R245 R432 R326 R371 U204 R213 R231 JP201 R307 R446 R621 R327 R230 X301 R309 U302 CB309 CB316 R324 CB313 R452 R453 R209 U201 CB311 R311 R369 CB312 R323 R370 R321 U303 CB310 XT201 1 2 3 4 5 6 7 8 R379 R310 R368 D502 R372 R515 R516 R517 R513 R514 U203 C303 D401 R411 R439 R313 R366 R367 R317 R316 R429 R518 R434 R433 R430 R315 R314 P301 T301 X403 X401 R450 X402 D403 D402 R413 R454 R511 CB203 R512 C402 CB405 R404 R318 X701 1 C207 C401 C403 L401 X704 1 CB413 L402 R401 CB401 U405 X702 1 1 Location of peripheral resistors on Top Side 4-5 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration R403 X804 CB402 CB403 CB417 U406 CB415 L602 C617 R623 R624 D608 Q603 R627 D609 D602 C605 R616 R617 C618 U603 R642 Q601 R620 R643 C614 R638 R501 CB408 R414 R644 C613 R519 CB414 R444 CB418 Q602 R507 R520 CB406 R407 R451 CB419 R606 R628 R604 R441 R406 R455 R377 R609 R442 R456 U408 R418 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 R427 R445 R423 R605 CB504 R428 CB411 CB404 U404 CB416 R443 U402 U407 C606 R618 R424 R341 C615 R339 R619 Q605 R416 R335 U304 CB318 R373 R612 R614 CB409 C406 R410 C612 R505 C619 U602 R438 R342 R319 C404 CB412 R405 U401 D603 CB611 R611 C621 C616 R610 R254 R253 R236 CB502 R437 R320 C620 CB607 CB613 CB604 R255 R256 CB605 R608 CB608 C201 R305 R378 Q604 R257 R258 R238 CB602 CB603 R207 R259 CB612 C202 Y201 C206 R241 CB606 R336 U305 CB615 CB206 C205 CB205 R243 R333 R375 R252 Y202 R239 R240 R419 R625 R306 R376 R374 CB609 C212 R247 R244 R425 R344 R426 R626 R402 CB410 R340 R440 R202 R246 R417 R337 R201 C210 C209 CB317 R206 U403 R343 C203 C204 R448 R447 CB407 R415 R409 R420 R205 R203 C211 R204 R219 R221 R220 R222 R251 R224 R225 R250 R223 R226 R232 R412 R421 R449 R435 R436 R422 R248 C405 1 Y401 1 C609 X801 X802 X803 1 1 Figure 4-5 Location of peripheral resistors on Bottom Side Table 4-4 Resistors for safety device D601 Component Description R247 Connect potentiometer to sensor input C (default: assembled) R251 Connect potentiometer to sensor input D (default: assembled) R239/R240 Voltage divider to adapt VDDP to VAREF of safety device (default: assembled) R252 Connect P3.6 (SLSO01) with /CS of safety device (default: assembled) R253 Connect P3.2 (SSC0) to SCLK of safety device (default: assembled) R254 Connect P2.11 (SSC1) to SCLK of safety device (default: not assembled) R255 Connect P3.4 (SSC0) to MTSR of safety device (default: assembled) R256 Connect P2.12 (SSC1) to MTSR of safety device (default: not assembled) R257 Connect P3.3 (SSC0) to MRST of safety device (default: assembled) R258 Connect P2.10 (SSC1) to MRST of safety device (default: not assembled) User’s Manual 4-6 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration Note: All resistors are red marked in the following figures R403 X804 CB402 CB403 U406 CB417 CB415 R624 L602 D608 Q603 R627 D609 D602 C606 R623 R616 R617 C618 U603 C617 C605 R501 CB408 R414 R340 R644 R643 R642 C614 R638 R519 CB414 R444 CB418 Q602 R507 R520 CB406 R407 R451 CB419 R606 R628 R604 R441 R406 R455 R377 R609 R442 R456 U408 R418 Q406 Q404 Q402 Q405 Q403 Q401 R338 R334 R427 R445 R423 R605 CB504 R428 R335 U304 CB318 R612 R373 R618 R424 C613 R505 R610 U602 X802 X803 1 User’s Manual R339 R619 Q605 R416 CB411 CB404 U404 CB416 R443 U402 U407 Q601 R620 Figure 4-6 R614 CB409 C406 D603 CB611 R611 C621 C616 CB502 R438 R342 R319 C404 CB412 R405 U401 C612 CB613 CB604 R254 R253 R236 R437 R320 C620 CB607 C619 R255 R256 CB605 R608 CB608 C201 R378 R336 Q604 R257 R258 R238 CB602 CB603 R207 R259 C202 Y201 C206 R241 CB606 CB612 R305 CB317 CB615 CB206 C205 CB205 R243 R333 R375 R252 Y202 R239 R240 R419 R625 R306 R376 R374 CB609 C212 R247 R244 R425 R344 R426 R626 R402 CB410 R410 R341 C615 R440 R202 R246 R417 R337 R201 C210 C209 R343 R206 U403 U305 C203 C204 R448 R447 CB407 R415 R409 R420 R205 R203 C211 R204 R219 R221 R220 R224 R222 R251 R223 R250 R225 R226 R232 R412 R421 R449 R435 R436 R422 R248 C405 1 Y401 1 C609 X801 1 D601 Location of resistors for safety device on Bottom Side 4-7 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Configuration User’s Manual 4-8 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Software 5 TriBoard Software 5.1 Requirements To install the software from your TriBoard CD you need a PC with Windows95/98/ME, Windows 2000, Windows XP, Windows Vista or Windows 7. 5.2 Software Overview The CD does not contain any tool. For the availablity for Demo Versions of the different Tools, please contact the toolvendor directly (e.g. Tasking, Hitex, Lauterbach, GreenHills, HighTec...). To install tools for compiling and debugging use seperat CD’s from Toolvendors. There are also some application notes and software examples. The data sheets of all used parts can be found in the “TriBoard_Components” directory. The manuals for the microcontrollers and the Easy Kit are located in the “Manual” folder. Some useful tools like Acrobat Reader are stored in the “Utilities” directory. The current Errata Sheet can be found in the directory “Errata Sheet”. To make sure you have always the most recent one, please contact your local FAE. Note: For more details see the file ReadMe.txt. 5.3 Software Installation To install tools for the TriCore insert the CD from the Toolvendor and start the file “setup.exe” if the CD is not automatically started. Follow the instructions of the installationprogram. User’s Manual 5-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual TriBoard Software User’s Manual 5-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Signal Description 6 Signal Description For more information about the signals please see the user manuals for TC1728 and/or the schematics of the board. Table 6-1 Power Signals Short Name Description VCC_IN Supply Input (5,5V...50V(40V)) VIN Input voltage of power supply device GND Ground VDD Core Supply Voltage (1,3V) VDDP Port Supply Voltage (3,3V) V5 EVR Supply Voltage (5V) VDDESB Emulation Stand-by SRAM Supply Voltage (1,3V) VSSM ADC Analog Part Ground VDDM ADC Analog Part Supply Voltage (5V) VAGND0 ADC Reference Ground VAREF0 ADC0 Reference Voltage (VDDM) VDDP_CIC Port Supply Voltage safety device (3,3V) VAGND_CIC ADC Reference Ground safety device VAREF_CIC ADC Reference Voltage safety device (2,5V) Table 6-2 Reset Signals Short Name Description /PORST Power On Reset /ESR0_/HDRST External Service Request 0 (Hardware Reset) /RESET_CIC Reset safety device Table 6-3 Interrupt Signals Short Name Description /ESR1_/NMI External Service Request 1 (Non Maskable Interrupt) REQ[0...1] / P3[10...11] External Trigger Input 0...1 REQ[2...3] / P0[6...7] External Trigger Input 2...3 REQ[4...5] / P0[14...15] External Trigger Input 4...5 User’s Manual 6-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Signal Description Table 6-3 Interrupt Signals REQ9 / P0.11 External Trigger Input 9 REQ15 / P1.0 External Trigger Input 15 Table 6-4 Clock Signals Short Name Description XTAL1 Crystal Oscillator Input XTAL2 Crystal Oscillator Output XTAL1_CIC Crystal Oscillator Input safety device XTAL2_CIC Crystal Oscillator Output safety device Table 6-5 Debug Signals Short Name Description /TRST Test Reset TCLK Test Clock TMS Test Mode Select TDI Test Data Input TDO Test Data Output /TESTMODE Test Mode Select Input /BRKIN TriCore Breakpoint Input /BRKOUT TriCore Breakpoint Output TCLK_CIC Test Clock safety device TMS_CIC Test Mode Select safety device TDI_CIC Test Data Input safety device TDO_CIC Test Data Outpu safety device MBC_CIC Monitor & Bootstrap loader Control line safety device Table 6-6 Peripheral Signals Short Name Description P3.0 Receive Data ASC0 P3.1 Transmit Data ASC0 P3.9 Receive Data ASC1 P3.8 Transmit Data ASC1 SCLK0 / P3.2 Clock Line SSC0 User’s Manual 6-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Signal Description Table 6-6 Peripheral Signals MRST0 / P3.3 Master Receive / Slave Transmit SSC0 MTSR0 / P3.4 Master Transmit / Slave Receive SSC0 SLSOX0 / P3.5 Slave Select Output 0 (SSCX) SLSOX1 / P3.6 Slave Select Output 1 (SSCX) SLSOX2 / P3.7 Slave Select Output 2(SSCX) P2.11 Clock Line SSC1 P2.10 Master Receive / Slave Transmit SSC1 P2.12 Master Transmit / Slave Receive SSC1 P3.13 CAN Transmitter Output 0 P3.12 CAN Receiver Input 0 P3.15 CAN Transmitter Output 1 P3.14 CAN Receiver Input 1 P4.1 CAN Transmitter Output 2 P4.0 CAN Receiver Input 2 P0 [0...7] General Purpose I/O Port 0 (HWCFG) P5 [0...7] General Purpose I/O Port 5 (used for LED´s) P5.8 E-Ray Channel A transmit Data Output P5.10 E-Ray Channel A transmit Data Output enable P5.14 E-Ray Channel A Receive Data Input 0 P5.9 E-Ray Channel B transmit Data Output P5.11 E-Ray Channel B transmit Data Output enable P5.15 E-Ray Channel B Receive Data Input 0 P2.4 MLI0 receive channel clock P2.5 MLI0 receive channel ready output P2.6 MLI0 receive channel valid input P2.7 MLI0 receive channel data input P2.0 MLI0 transmit channel clock P2.1 MLI0 transmit channel ready input P2.2 MLI0 transmit channel valid output P2.3 MLI0 transmit channel data output P6.1 / FCLP0A MSC0 differential driver clock output positive A User’s Manual 6-3 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Signal Description Table 6-6 Peripheral Signals P6.0 / FCLN0 MSC0 differential driver clock output negative P6.3 / SOP0A MSC0 differential driver serial data output positive A P6.2 / SON0 MSC0 differential driver serial data output negative AN[0...35] Analog Inputs P1[12...14] ADC0 External Multiplexer Control P0[0...15] General Pupose I/O Port 0 P1[0...15] General Pupose I/O Port 1 P2[0...13] General Pupose I/O Port 2 P3[0...15] General Pupose I/O Port 3 P4[0...3] General Pupose I/O Port 4 P5[0...15] General Pupose I/O Port 5 P6[0...3] General Pupose I/O Port 6 P8[0...14] General Pupose I/O Port 8 P9[2...8] General Pupose I/O Port 9 P10[0...3] General Pupose I/O Port 10 P11[0...15] General Pupose I/O Port 11 Table 6-7 Safety device Signals Short Name Description SENA Sensor Input A SENB Sensor Input B SENC Sensor Input C SEND Sensor Input D SCLK_CIC Clock Line SAK-CIC61508 MRST_CIC Master Receive / Slave Transmit SAK-CIC61508 MTSR_CIC Master Transmit / Slave Receive SAK-CIC61508 /CS_CIC Slave Select Input SAK-CIC61508 SYSDISA System Disable Output A SYSDISB System Disable Output B SYSDISC System Disable Output C User’s Manual 6-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Connector Pin Assignment 7 Connector Pin Assignment The TriBoard will be shipped with four male (plug) connectors on top layer and four female (socket) connectors on bottom layer. The default connectors are 80-pol. Board to Board connectors from Samtec: http://www.samtec.com Plug: FTSH-140-02-L-DV-ES-A Socket: FLE-140-01-G-DV-A User’s Manual 7-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Connector Pin Assignment 7.1 TC1728 Connector / Top View BUS EXPANSION (X801,X901) GND GND Figure 7-1 User’s Manual 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 PERIPHERALS (X802,X902) GND GND GND GND VCC_IN VCC_IN /ESR1 GND EN00 / P2.8 SDI0 / P2.13 FCLP0A / P6.1 FCLN0 / P6.0 SOP0A / P6.3 SON0 / P6.2 SLSO00_10 / P3.5 SLSO02_12 / P3.7 SLSO04_14 / P2.8 SLSO06 / P3.8 GND XTAL1 XTAL2 RXD0 / P3.0 TXD0 / P3.1 RXDCAN0 / P3.12 TXDCAN0 / P3.13 SCLK0 / P3.2 MTSR0 / P3.4 MRST0 / P3.3 REQ0 / P3.10 REQ2 / P0.6 VDDESB 3V3 3V3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GND GND VCC_IN VCC_IN /ESR0 GND /PORST EN01 / P2.9 P1.15 P9.5 P9.6 SLSI1 / P2.13 SLSO01_11 / P3.6 SLSO03_13 / P2.1 SLSO05_15 / P2.9 SLSO17 / P1.10 GND SYSCLK / P4.3 RXD1 / P3.9 TXD1 / P3.8 RXDCAN1 / P3.14 TXDCAN1 / P3.15 SCLK1 / P2.11 MTSR1 / P2.12 MRST1 / P2.10 REQ1 / P3.11 REQ3 / P0.7 GND 3V3 3V3 Connector for TC1728 - Pinout (Part I, Top View) 7-2 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Connector Pin Assignment ADC (X803, X903) VSSM VSSM AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 VSSM VDDM 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 VAGND0 43 VAREF0 45 VSSM 47 AN32 49 AN33 51 AN34 53 AN35 55 57 59 VSSM 61 P8.8 63 P8.10 65 P8.12 67 3V3 69 AD0EMUX0 / P1.12 71 AD0EMUX1 / P1.13 73 AD0EMUX2 / P1.14 75 77 REQ5 / P0.15 79 Figure 7-2 User’s Manual 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 GPTA / MLI (X804,X904) VSSM VSSM AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM VDDM GND GND P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P0.8 P0.9 P0.10 P0.11 P0.12 P0.13 P0.14 P0.15 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P1.8 P1.9 P1.10 P1.11 P4.0 P4.1 P4.2 P4.3 TCLK0 / P2.0 TREADY0 / P2.1 TVALID0 / P2.2 TDATA0 / P2.3 3V3 3V3 VAGND0 VSSM VSSM P8.9 P8.11 P8.13 3V3 P10.0 P10.1 P10.2 REQ4 / P0.14 P10.3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 2 GND 4 GND 6 P5.8 8 P5.9 10 P5.10 12 P5.11 14 P5.12 16 P5.13 18 P5.14 20 P5.15 22 P5.0 24 P5.1 26 P5.2 28 P5.3 30 P5.4 32 P5.5 34 P5.6 36 P5.7 38 40 42 P9.2 44 P9.3 46 P9.4 48 P9.7 50 P9.8 52 P8.0 54 P8.1 56 P8.2 58 EMGSTOP / P1.4 60 P8.3 62 P8.4 64 P8.5 66 P8.6 68 P8.7 70 RDATA0 / P2.7 72 RVALID0 / P2.6 74 RREADY0 / P2.5 76 RCLK0 / P2.4 78 3V3 80 3V3 Connector for TC1728 - Pinout (Part II, Top View) 7-3 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Connector Pin Assignment 7.2 Power connector pinout +5,5V...50V(40V) GND Figure 7-3 USB connector pinout Figure 7-4 7.4 2 (D-) 1 (Vbus) 3 (D+) 4 (GND) USB connector Pinout Flexray Pinout 6 Figure 7-5 User’s Manual BP 2 BM 1 7 8 3 9 4 5 GND 7.3 Power connector pinout Flexray Pinout (SUBD-9 Plug) 7-4 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Connector Pin Assignment CAN connector pinout 4 6 8 1 0 1 3 5 7 9 Figure 7-6 CAN connector pinout (IDC10) GND /PORST GND GND 4 6 8 10 12 14 16 1 3 5 7 9 11 13 15 /BRKIN TCK /TRST TDI OCDS connector pinout (IDC16) User’s Manual Key GND GND 8 10 1 3 5 7 9 /RESET 6 USR1_IN 4 USR0_IO 2 DAP0 DAP1 Figure 7-8 GND DAP connector pinout +3V3 7.7 2 TDO TMS Figure 7-7 /BRKOUT OCDS connector pinout +3V3 7.6 GND CANH CANL 2 GND 7.5 DAP connector pinout (FTSH10) 7-5 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Connector Pin Assignment User’s Manual 7-6 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Schematic and Layout 8 Schematic and Layout 8.1 Schematic User’s Manual 8-1 V 1.0, 2011-02 Figure 8-1 User’s Manual 8-2 D C B A 1 1 PORT[0..10] 2 /TESTMODE JTAG.. /ESR0 /PORST MiniWiggler and DAP OCDS.sch /ESR0 /PORST PORT[0..10] /TESTMODE JTAG.. PORT[0..10] POWER SUPPLY /ESR1 Supply.sch AN[0..35] 3 3 XTAL[1..2] /TESTMODE JTAG.. PORT[0..10] Clock. Config and Jtag Clk_Cfg_Jtag.sch GPTA/MSC/MLI/CAPCOM/GPT/ADC GPTA_ADC.sch 2 4 4 PORT[0..10] Flexray, CAN and Eeprom Flexray_CAN_Eeprom.sch 5 5 PORT[0..10] XTAL[1..2] AN[0..35] /ESR1 /PORST /ESR0 6 6 /ESR0 XTAL[1..2] NC3[1..80] NC4[1..80] Infineon Technologies AG XTAL[1..2] /ESR0 /PORST /ESR1 AN[0..35] 7 Sheet: 8 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\TriBoard_TC1728_V10.prj TriBoard TC1728 Project PORT[0..10] NC1[1..80] NC2[1..80] NC3[1..80] NC4[1..80] Connector Socket /PORST NC2[1..80] Connectf.sch /ESR1 NC1[1..80] AN[0..35] Connector Plug PORT[0..10] Connectm.sch 7 8 8 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - Project V 1.0, 2011-02 NC4[1..80] NC3[1..80] NC2[1..80] NC1[1..80] 8-3 D C B A 1 TDO_CIC SYSDISB SYSDISA VDDP_CIC GND VAGND_CIC VAREF_CIC SEND P1_0_CIC P1_1_CIC P1_5_CIC /CS_CIC P3_7_CIC SYSDISB SYSDISA P3_2_CIC P3_3_CIC P3_4_CIC P3_5_CIC /RESET_CIC P2_3_CIC P2_4_CIC P2_5_CIC P2_6_CIC P1_6_CIC P1_7_CIC TMS_CIC TCK_CIC TDO_CIC TDI_CIC SENA SENB SENC R227 10K MBC_CIC SCLK_CIC MTSR_CIC MRST_CIC XTAL2_CIC XTAL1_CIC GND VDDC_CIC CON1X19_opt 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 X202 620R R235 620R R234 620R R233 GND C212 10nF SEND GND C211 10nF SENC VDDP_CIC LS T67K D203 LS T67K D202 CON1X19_opt 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 X201 GND 0R R251 0R R247 LS T67K D201 VAGND_CIC R250 0R 10K 2 R249 R248 0R VAREF_CIC VAGND_CIC R246 0R 10K 2 R245 R244 0R VAREF_CIC 3 1 3 1 2 D204 1 11 12 13 14 2 3 4 SCLK_CIC MTSR_CIC MRST_CIC VAGND_CIC 2 24 25 27 28 29 9 10 38 MBC_CIC TMS_CIC TCK_CIC TDO_CIC TDI_CIC 6 SAK-CIC61508 VAGND VAREF P1.0 / RXD_0 P1.1 / TXD_0 P1.5 P1.6 P1.7 P0.3 / SCLK_1 P0.4 / MTSR_1 P0.5 / MRST_1 MBC TMS P0.0 / TCK_0 P0.2 / TDO_0 P0.1 / TDI_0 RESET XTAL2 XTAL1 U202 VSSP 2K R259 26 23 22 21 20 17 16 15 31 30 37 36 35 34 33 32 7 8 VDDP_CIC P2.7 / AN7 P2.6 / AN6 P2.5 / AN5 P2.4 / AN4 P2.3 / AN3 P2.2 / AN2 P2.1 / AN1 P2.0 / AN0 P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 VSSC VDDC 19 3 10 8 GND MRST_CIC GND GND GND 4 2 /RESET_CIC MRST_CIC MTSR_CIC SCLK_CIC /CS_CIC OUT GND OUT 0R R231 3 6 3 4 1 3 5 7 9 11 13 15 GND GND R230 GND opt C207 1uF VAREF_CIC GND C208 22µF/10V 1 R255 0R_opt 0R_opt R258 0R_opt JP203 2 RESET 0R R257 0R 0R R254 R256 R253 0R R252 OCDS1_CIC GND R202 opt R201 10K +3V3 C202 opt D205 LP T67K R213 680R GND R207 opt XTAL2 XTAL1 2 4 6 8 10 12 14 16 5 /PORST P2_10 P3_3 P2_12 P3_4 P2_11 P3_2 P3_6 GND 5 /RESET_CIC MBC_CIC GND VDDP_CIC GND Y201 2 TMS VCC TDO GND CPUCLOCK GND TDI PORST TRST BRKOUT TCK GND BRKIN OCDSE N.C. KEY X203 1 XTAL2 C201 opt opt R206 opt XTAL1 VDDP_CIC VAGND_CIC REF192GS GND SLEEP V+ U204 IN 0R 0R R205 50R_opt R204 R203 C204 33pF GND U203 TLE4274DV33 MBC_CIC R232 1K TCK_CIC TDI_CIC TMS_CIC TDO_CIC CB205 220n GND CB207 100n VDDP_CIC 1 CB209 100n VIN 4 GND C203 33pF ONLY ON REQUEST P3_7_CIC GND /CS_CIC P3_5_CIC P3_4_CIC P3_3_CIC P3_2_CIC SYSDISA SYSDISB SEND P2_6_CIC P2_5_CIC P2_4_CIC P2_3_CIC SENC SENB SENA XTAL2 XTAL1 XTAL[1..2] /TESTMODE Crystal 20MHz VCC VCC GND OE OE XT201 CB204 100n VDDC_CIC GND VDDP_CIC GND 1 4 11 14 7 XTAL[1..2] /TESTMODE 3 CB203 100n +3V3 18 GND VDDP 22pF_opt C206 CSTCR6M00G C205 GND VDDP_CIC 22pF_opt /RESET_CIC CB206 100n R243 0R R242 10K VAGND_CIC 2 R241 0R VAREF_CIC Y202 2 GND 5 P1_0_CIC P1_1_CIC P1_5_CIC P1_6_CIC P1_7_CIC VAREF_CIC S202 620R R238 0R R237 10K R236 0R VAGND_CIC 2 GND R228 JP202 SENB 1K R240 JP201 SENA VAREF_CIC RESET_CIC CB208 100n R229 10K XTAL2_CIC XTAL1_CIC XTAL2_CIC XTAL1_CIC /RESET_CIC 1K6 LS T67K VDDP_CIC GND 2 R239 C210 10nF VDDP GND C209 10nF /RESET_CIC SENB SENA VDDCORE 1 3 1 3 3 1 3 1 2 1 3 GND User’s Manual 2 Figure 8-2 P3_10 P3_11 P2_10 P3_3 P3_14 P3_12 P3_9 P3_0 /TRST DAP0 DAP1 P9_5 XTAL2 XTAL1 137 144 161 130 134 143 138 136 117 114 115 112 111 103 102 118 JTAG / DAP / OCDS1 CLOCK & TESTMODE VSS VSS TC1728 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 680R R225 680R R223 680R R221 680R P3.13 / OUT95 / TXDCAN0 / TXD0 TC1728 6 P3.10 / OUT92 / REQ0 P3.11 / OUT93 / REQ1 P2.10 / MRST1A R209 10K +3V3 JTAG.. 8 126 127 131 163 162 132 129 133 142 128 135 P3_5 P3_6 P3_7 P2_12 P2_11 P3_4 P3_2 P3_15 P3_13 P3_8 P3_1 CFG0 CFG1 CFG2 CFG3 CFG4 CFG5 CFG6 CFG7 1 2 3 4 5 6 7 8 Infineon Technologies AG 7 Sheet: 1 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Clk_Cfg_Jtag.sch 16 15 14 13 12 11 10 9 8 PORT[0..10] DIPSW-8 S201 GND Switch ON means the corresponding signal is low. Switch OFF means the corresponding signal is high. TriBoard TC1728 Clock, Config, Jtag and CIC61508 P3.5 / SLSO00_10 P3.6 / SLSO01_11 P3.7 / SLSI01 / OUT89 / SLSO02_12 P2.12 / MTSR1A / SOP0B P2.11 / SCLK1A / FCLP0B P3.4 / OUT88 / MTSR0 P3.2 / OUT86 / SCLK0 P3.14 / OUT96 / RXDCAN1 / RXD1B / SDI2P3.15 / OUT97 / TXDCAN1 / TXD1 P3.3 / OUT87 / MRST0 /TRST JTAG.. PORT[0..10] P3.1 / OUT85 / TXD0A 680R R226 680R R224 680R R222 680R R220 P3.8 / SLSO06 / OUT90 / TXD1 / ECTT1 / REQ14 P3.12 / OUT94 / RXDCAN0 / RXD0B P3.9 / OUT91 / RXD1A GND P9_6 113 101 104 7 NOTE: S201 is for boot configuration (about configuration see the manual of assembled device). R219 ASC / CAN / SSC / EXT. REQ P1.15 / BRKIN / BRKOUT TRST P9.6 / TDO / BRKIN / BRKOUT TCK / DAP0 TMS / DAP1 P9.5 / TDI / BRKIN / BRKOUT XTAL2 XTAL1 TESTMODE U201B P3.0 / OUT84 / RXD0A / REQ6 U201C P1_15 P1_15 /TESTMODE 6 1 1 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - Config, Clock, JTAG and CIC61508 V 1.0, 2011-02 D C B 1 PORT[0..10] 2 +3V3 10K 3 R356 10K R355 GND CB319 100n +3V3 7 3 8 4 CS SCK SI SO 1 6 5 2 R375 0R AT25128N-10SI2.7 HOLD WP VCC GND U306 R372 0R 4 R373 0R R374 0R 0R R354 100K R353 +3V3 4 P5_9 P5_11 P5_15 P0_15 P3_5 P3_2 P3_4 P3_3 P8_7 P8_5 P8_6 P8_4 R307 4K7 +3V3 P5_14 P5_10 P5_8 P0_14 P3_15 P3_14 P3_13 P3_12 5 GND GND R327 opt 2 1 15 INH1B INH2B WAKEB 9 3 13 12 4K7 R322 4K7 STBNB ERRNB RXENB R323 +3V3 R326 opt GND R325 opt GND R324 opt 0R_opt 0R_opt R320 R319 TXDB TXENB RXDB BGEB ENB R321 4K7 +3V3 5 6 7 8 2 1 15 9 3 5 6 7 8 INH1A INH2A WAKEA R313 opt 100n GND GND AS8221 INH1 INH2 WAKE ERRN RXEN STBN EN 6 TXD TXDEN RXD BGE U303 AS8221 INH1 INH2 WAKE ERRN RXEN STBN EN TXD TXDEN RXD BGE U302 100n CB318 +5V 13 12 4K7 6 CB317 +5V 4K7 STBNA ERRNA RXENA GND R312 opt GND GND R308 TXDA TXENA RXDA BGEA ENA R309 +3V3 R379 0R 0R R339 0R R333 GND R311 opt R376 0R GND R310 opt 0R_opt 0R_opt R306 R305 R377 0R GND R378 0R 5 0R R340 GND VBAT VDD VIO NU / VBUF BM BP NU / TRXD1 NU / TRXD0 GND VBAT VDD VIO NU / VBUF BM BP 6 8 5 7 6 8 5 7 R341 0R +3V3 R335 0R R337 0R R342 0R 120R R344 R343 0R R336 0R 120R R338 10 11 GND 10 11 +3V3 GND opt 0R R368 VIN 0R 0R R370 R369 GND +5V GND +5V 4 1 opt T302 R328 3 2 +3V3 GND +5V R331 51R C304 10nF R332 0R GND R330 51R R317 51R C303 10nF ONLY WITH NXP TJA1080 GND 0R R371 opt B82790-C0513-N201 R329 GND 2 4 6 8 10 2 4 6 8 10 R318 0R GND R316 51R ONLY WITH NXP TJA1080 GND +5V GND BMB BPB 3 2 CAN1 1 3 5 7 9 X302 CAN0 1 3 5 7 9 X301 GND GND 7 X2 5 9 4 8 3 7 2 6 1 X1 X2 5 9 4 8 3 7 2 6 1 X1 GND GND Sheet: 2 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Flexray_CAN_Eeprom.sch Infineon Technologies AG TriBoard TC1728 Flexray, CAN and Eeprom 16 14 19 4 20 17 18 opt T301 B82790-C0513-N201 R315 4 1 R314 GND VIN 0R GND BMA BPA GND ONLY WITH NXP TJA1080 16 14 19 4 20 17 18 0R R367 R366 ONLY WITH NXP TJA1080 TLE6250GV33 TXD CANL GND INH VCC RM RXD CANH U305 0R R334 TLE6250GV33 TXD CANL GND INH VCC RM RXD CANH U304 NU / TRXD1 NU / TRXD0 1 2 3 4 1 2 3 4 +3V3 7 CB309 100n 3 CB310 100n CB313 100n A PORT[0..10] 2 CB311 100n CB314 100n 8-4 CB312 100n User’s Manual CB315 100n Figure 8-3 CB316 100n 1 8 CHANNELB P302 CHANNELA P301 8 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - Flexray, CAN and Eeprom V 1.0, 2011-02 8-5 D C B A 1 PORT[0..10] GND P401 1 2 3 4 IN 7 4 8 5 6 PORT[0..10] 2K2 R406 93LC46B-I/SN 1 2 3 VDD_FT 8pF VCC CS GND CLK D DNC Q ORG U402 GND 3 8pF C405 C404 GND GND OUT GND 27R 27R R403 R402 GND opt 12K/1% R404 VDD_FT 3,3uF C406 2 P1_15 P1_15 P1_15 P1_15 GND P1_0 1K R401 P1_0 VDD_FT R407 10K 10K R405 10K R442 R441 VDD_FT GND +1V8 GND CB405 100n Y401 NX3225SA-12MHz GND C401 10µ/6V VDD_FT GND C402 4u7/6V 2 0R_opt R429 0R_opt R427 0R_opt R425 0R_opt R430 USR1_DAP 0R_opt R428 USR1 0R_opt R426 2 4 6 8 10 12 14 16 GND 3 /TESTMODE /TESTMODE /TESTMODE /DBGRST /BRKOUT GND GND +3V3 0R_opt /BRKIN PWREN SUSPEND TEST EECS EECLK EEDATA RESET OSCO OSCI REF DP DM VREGIN VREGOUT 100n 100n 100n R424 60 36 13 63 62 61 14 3 2 6 8 7 50 49 CB410 CB411 CB412 3 VDD_FT FT2232HL BCBUS0 BCBUS1 BCBUS2 BCBUS3 BCBUS4 BCBUS5 BCBUS6 BCBUS7 BDBUS0 BDBUS1 BDBUS2 BDBUS3 BDBUS4 BDBUS5 BDBUS6 BDBUS7 ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 OCDS1 /TESTMODE VCC TMS GND TDO GND CPUCLOCK PORST TDI BRKOUT TRST GND TCK OCDSE BRKIN KEY N.C. X401 U401 100n 100n 100n 100n ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 CB409 CB404 CB403 CB402 1 3 5 7 9 11 13 15 /TESTMODE 4 USR1_DAP USR1 P9_5 /TRST DAP0 /BRKIN DAP1 P9_6 /DBGRST 1K R414 BDBUS0 BDBUS1 38 39 40 41 43 44 45 46 VDD_FT ACBUS0 ACBUS1 ACBUS2 ACBUS3 ACBUS4 ACBUS5 ACBUS6 ACBUS7 26 27 28 29 30 32 33 34 48 52 53 54 55 57 58 59 ADBUS0 ADBUS1 ADBUS2 ADBUS3 ADBUS4 ADBUS5 ADBUS6 ADBUS7 1K_opt R450 L402 VDD_FT 2 10K R418 2 /DBGRST DAP1 DAP0 USER0 USER1 RESET 0R 0R_opt R432 5 3 P3_1 +3V3 /ESR0 1 3 5 7 9 /PORST /PORST /ESR0 VREF GND GND KEY GND Q406 BSS138N 2 10K R419 Q404 BSS138N 2 R417 10K +3V3 ADBUS1 ADBUS2 ACBUS5 ACBUS3 ACBUS7 ACBUS2 ACBUS6 ACBUS4 ACBUS5 DAP2WIRE R431 2 4 6 8 10 3 3 X402 Q405 BSS138N 3 Q403 BSS138N 3 R416 10K VDD_FT 3 R410 10K VDD_FT 5 Q401 BSS138N ADBUS0 ADBUS1 ADBUS3 ADBUS6 ACBUS0 ACBUS1 R412 680R ADBUS4 2 D402 LP T67K VDD_FT DAP1 DAP0 P9_6 USR1_DAP /DBGRST BDBUS1 VDD_FT BDBUS0 D401 LB T673 R411 100R VDD_FT C403 MMZ1608R300A 4u7/6V GND 16 17 18 19 21 22 23 24 GND GND GND CB413 100n 4 1 L401 MMZ1608R300A U405 TLE4274GSV33 USB Connector CB406 100n VDD_FT GND CB401 100n 1 2 GND 1 2 GND +3V3 R440 0R R420 1K +3V3 10K R413 Q402 BSS138N P1_3 P1_11 P1_10 P1_1 P1_0 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 VCC GND 5 22R_opt 22R_opt R438 R437 22R_opt 22R_opt R436 22R_opt R435 0R_opt R434 R433 GND VDDESB 6 GND /PORST DAI2 DAI1 DAI4 DAI3 /ESR0 /BRKOUT_ETK /BRKIN_ETK 3 ACBUS2 100n ACBUS6 GND R446 4K7 GND 1 5 ACBUS7 VDD_FT CB418 3 1 ACBUS3 100n GND R445 4K7 GND VDD_FT CB416 5 R444 4K7 ACBUS5 1 3 VDD_FT CB414 ADBUS2 100n GND GND 2 3 1 GND B GND B GND B A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 2 4 6 2 4 6 2 4 6 4 5 5K1 VDDP VDDESB DAP1 DAP0 P9_5 P9_6 USR1 GND P1_0 P9_6 GND P9_6 DAP1 GND 22R_opt R439 100n CB419 0R_opt 0R R423 100n R456 CB417 0R_opt 0R R451 100n R455 CB415 /TRST GND +3V3 GND +3V3 GND +3V3 100n GND DAP1 VDD_FT CB408 5K1 R454 BAT54 0R_opt 0R_opt 0R_opt D403 1 /DBGRST R453 3 DAP0 P9_5 DAP1 /TRST JTAG.. FOR USING WIGGLER WITH JTAG: Assemble R447-R451 Remove R455-R456 7 7 Sheet: 3 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\OCDS.sch Infineon Technologies AG TriBoard TC1728 miniWiggler, DAP and ETK ETK_CON_opt B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 X403 SN74LVC1T45DBV DIR A VCCA VCCB U408 SN74LVC1T45DBV DIR A VCCA VCCB U407 SN74LVC1T45DBV DIR A VCCA VCCB U406 Y VCC 74LVC1G125 ADBUS2 GND A /OE U404 +3V3 R447 R448 R449 R452 10K +3V3 R422 opt GND R421 opt GND USR8 GND DAP0 TDI TMS USR0 /TRST_J /RESET CB407 100n +3V3 ADBUS1 18 16 14 12 9 7 5 3 20 10 6 R443 10K ACBUS4 VDD_FT SN74AHC244PW 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 G G U403 P1_15 2 4 6 8 11 13 15 17 1 19 R409 10K +3V3 R415 10K +3V3 1 VDD_FT GND GND GND GND GND GND GND GND 1 5 11 15 25 35 47 51 3 12 37 64 VCORE VCORE VCORE 9 4 VPLL VPHY 20 31 42 56 VCCIO VCCIO VCCIO VCCIO AGND 10 1 1 1 1 User’s Manual P3_1 Figure 8-4 P3_0 1 8 JTAG.. 8 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - miniWiggler JDS, DAP and ETK V 1.0, 2011-02 Figure 8-5 User’s Manual 8-6 D C B A 172 171 170 11 12 165 141 140 139 124 123 82 83 84 85 89 91 92 100 125 P9_2 P9_3 P9_4 P9_7 P9_8 P2_13 P8_0 P8_1 P8_2 P8_3 P8_4 P8_5 P8_6 P8_7 P8_8 P8_9 P8_10 P8_11 P8_12 P8_13 1 145 146 147 148 166 167 173 174 149 150 151 152 168 169 175 176 116 119 93 98 99 108 109 110 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 GPTA / HWCFG / SSC / MLI / MSC / GPT12 / CAPCOM / REQ 3 4 TC1728 2 P8.0 / SCLK3 / CCPOS0C / T3INA/B / OUT48 P8.1 / MRST3 / CCPOS1C / T3EUDA/B / OUT49 P8.2 / MTSR3 / CCPOS2C / T4INA/B / OUT50 P8.3 / SLSI3 / CC61INC / CC61 / OUT51 / SLSO30 P8.4 / OUT99 / COUT62 / SLSO31 P8.5 / CC60INC / CC60 / OUT100 / SLSO32 P8.6 / OUT101 / COUT61 P8.7 / OUT102 / CC62 / CC62INC P8.8 / OUT56 / SLSO33 P8.9 / OUT57 / SLSO34 P8.10 / OUT105 P8.11 / OUT106 P8.12 / OUT107 P8.13 / OUT4 / COUT60 P2.13 / SLSI11 / SDI0 / CTRAPA / T12HRE / SLSO16 / T6OUT 3 4 P10.0 / MRST2B P10.1 / MTSR2B P10.2 / SCLK2B P10.3 / SLSO20 / SLSI2B P6.1 / OUT81 / FCLP0A P6.0 / OUT80 / FCLN0 P6.3 / OUT83 / SOP0A P6.2 / OUT82 / SON0 P2.8 / SLSO04 / SLSO14 / EN00 P2.9 / SLSO05 / SLSO15 / EN01 P0.0 / IN0 / HWCFG0 / OUT0 / OUT56 / CC60 / CC60INA/B P1.8 / IN24 / IN48 / MTSR1B / OUT24 / OUT48 / CCPOS2C / T4EUDA/B P0.1 / IN1 / HWCFG1 / OUT1 / OUT57 / SDI1 / COUT60 P1.9 / IN25 / IN49 / MRST1B / OUT25 / OUT49 / CCPOS1C / T2EUDA/B P0.2 / IN2 / HWCFG2 / OUT2 / OUT58 P1.10 / IN26 / IN50 / OUT26 / OUT50 / SLSO17 P0.3 / IN3 / HWCFG3 / OUT3 / OUT59 P1.11 / IN27 / IN51 / SCLK1B / OUT27 / OUT51 / CCPOS0C / T2INA/B P0.4 / IN4 / HWCFG4 / OUT4 / OUT60 P4.0 / IN28 / IN52 / OUT28 / OUT52 / RXDCAN2 P0.5 / IN5 / HWCFG5 / OUT5 / OUT61 P4.1 / IN29 / IN53 / OUT29 / OUT53 / TXDCAN2 P0.6 / IN6 / HWCFG6 / REQ2 / OUT6 / OUT62 P4.2 / IN30 / IN54 / OUT30 / OUT54 / EXTCLK1 / T2EUDA/B /CCPOS1A / T13HRB P0.7 / IN7 / HWCFG7 / REQ3 / OUT7 / OUT63 P4.3 / IN31 / IN55 / OUT31 / OUT55 / EXTCLK0 / T12HRE / CTRAPA P0.8 / IN8 / RXDA0 / OUT8 / OUT64 / T3OUT P2.0 / IN32 / OUT32 / OUT28 / TCLK0 / CC62INA/B / CC62 P0.9 / IN9 / RXDB0 / OUT9 / OUT65 / T6OUT P2.1 / IN33 / TREADY0A / OUT33 / SLSO03 / SLSO13 / T12INA/B / T12HRB / CCPOS0A P0.10 / IN10 / OUT10 / TXDA0 / OUT66 P2.2 / IN34 / OUT34 / TVALID0A / CC61INA/B / CC61 P0.11 / IN11 / OUT11 / TXDB0 / OUT67 / ECTT2 / REQ9 P2.3 / IN35 / OUT35 / TDATA0 / T4EUDA/B / CCPOS2A / T13HRC / T12HRC P0.12 / IN12 / OUT12 / TXENA / OUT68 / CTRAP / T13HRE P2.4 / IN36 / RCLK0A / OUT36 / COUT63 P0.13 / IN13 / OUT13 / TXENB / OUT69 P2.5 / IN37 / OUT37 / RREADY0A / CC60INA/B / CC60 P0.14 / IN14 / REQ4 / OUT14 / OUT70 / CC61INC / CC61 P2.6 / IN38 / RVALID0A / OUT38 / COUT62 P0.15 / IN15 / REQ5 / OUT15 / OUT71 / COUT61 P2.7 / IN39 / RDATA0A / OUT39 / COUT60 P1.0 / REQ15 / IN16 / OUT16 / OUT72 / T3OUT / BRKIN / BRKOUT P5.0 / IN40 / OUT40 / SLSO20 / CAPINA/B / CC62INA/B / CC62 / REQ7 P1.1 / IN17 / OUT17 / OUT73 / T13HRE / CTRAPB P5.1 / IN41 / OUT41 / SLSO21 P1.2 / IN18 / OUT18 / OUT74 P5.2 / IN42 / OUT42 / SLSO22 / COUT62 P1.3 / IN19 / OUT19 / OUT75 / COUT63 P5.3 / IN43 / OUT43 / SLSO23 P1.4 / IN20 / EMGSTOP / OUT20 / OUT76 / COUT61 P5.4 / IN44 / OUT44 / SLSO24 / SLSI2A P1.5 / IN21 / OUT21 / OUT77 P5.5 / IN45 / OUT45 / MRST2A P1.6 / IN22 / OUT22 / OUT78 P5.6 / IN46 / OUT46 / MTSR2A P1.7 / IN23 / OUT23 / OUT79 P5.7 / IN47 / OUT47 / SCLK2A P5.8 / TXDA1 / OUT6 / CC61INA/B / CC61 P5.9 / TXDB1 / RXDCAN0 / OUT7 P5.10 / TXENA / OUT8 / COUT61 P9.2 / COUT63 / OUT82 P5.11 / TXENB / OUT9 / COUT63 P9.3 / OUT83 / COUT62 P5.12 / OUT19 / SLSO07 / AD1EMUX0 / T3INA/B / T12HRB / CCPOS0A P9.4 / CC62INC / CC62 / OUT84 P5.13 / AD1EMUX1 / OUT20 / T3EUDA/B / T13HRB / CCPOS1A P9.7 / OUT87 / CC60 / CC60INC P5.14 / RXDA1 / AD1EMUX2 / OUT36 / T4INA/B / T13HRC / T12HRC / CCPOS2A P9.8 / OUT88 / COUT60 P5.15 / RXDB1 / OUT37 / TXDCAN0 U201D 2 23 24 25 26 157 156 159 158 164 160 94 95 96 97 86 87 88 90 74 75 76 77 78 79 80 81 1 2 3 4 5 6 7 8 13 14 15 16 17 18 19 9 P10_0 P10_1 P10_2 P10_3 P6_1 P6_0 P6_3 P6_2 P2_8 P2_9 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 P5_8 P5_9 P5_10 P5_11 P5_12 P5_13 P5_14 P5_15 5 P5_7 P5_6 P5_5 P5_4 P5_3 P5_2 P5_1 P5_0 5 LB T673 AN[0..35] 100R 100R R518 D505 LB T673 D508 LB T673 100R R515 D504 LB T673 D507 LB T673 100R R514 D503 LB T673 100R R517 100R R513 100R R516 0R 100R R512 D502 LB T673 D506 LB T673 R510 R511 D501 +3V3 AN[0..35] 1 6 67 66 65 64 63 62 61 36 60 59 58 57 56 55 50 49 48 47 46 45 44 43 42 41 40 39 38 37 35 34 33 32 31 30 29 28 PORT[0..10] AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 AN32 AN33 AN34 AN35 6 51 52 53 54 73 72 71 R505 0R VAGND0 0R 0R CB504 100n R507 VAREF0 VSSM CB502 R501 47n VDDM P1_12 P1_13 P1_14 Infineon Technologies AG 7 Sheet: 4 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\GPTA_ADC.sch 0R R520 8 PORT[0..10] VSSM VDDM +3V3 IF 3,3V ADC 0R +5V IF 5V ADC 8 R519 GND TriBoard TC1728 GPTA, MSC, MLI, GPT and ADC TC1728 VAGND0 VAREF0 VSSM VDDM P1.12 / AD0EMUX0 P1.13 / AD0EMUX1 P1.14 / AD0EMUX2 ADC / FADC AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AN16 / DIG0 / P11.0 AN17 / DIG1 / P11.1 AN18 / DIG2 / P11.2 AN19 / DIG3 / P11.3 AN20 / DIG4 / P11.4 AN21 / DIG5 / P11.5 AN22 / DIG6 / P11.6 AN23 / DIG7 / P11.7 AN24 / DIG8 / P11.8 AN25 / DIG9 / P11.9 AN26 / DIG10 / P11.10 AN27 / DIG11 / P11.11 AN28 / DIG12 / P11.12 AN29 / DIG13 / P11.13 AN30 / DIG14 / P11.14 AN31 / DIG15 / P11.15 AN32 AN33 AN34 AN35 U201E 7 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - GPTA, MSC, MLI and ADC V 1.0, 2011-02 D C B A +1V3 C613 4µ7/10V GND GND C614 1µ/6V GND 1 /ESR1 /ESR0 D605 LP T67K /ESR1 /ESR0 /PORST GND BC848C /PORST 82K R616 SS12 R617 620R +3V3 Q604 1 SS12 C611 22µ/10V Q_STBY R620 4K7 +3V3 2 4K7 GND R622 10K GND GND_A R621 D607 LP T67K GND RESET R626 4K7 +3V3 10K R602 VIN 10K +3V3 R601 220n +3V3 GND 15 C602 100n 12 14 20 21 22 GND_A GND_A GND_A GND_A GND_P WDI EN_uC EN_IGN SEL_LDO2 CCP C2- C2+ C1- C1+ IN IN IN C615 4µ7/10V 1 0R_opt 3 R623 0R RT RO_1 RO_2 WDO Q_T1 Q_T2 FB_EXT DRV_EXT Q_LDO2 Q_LDO1 Q602 BC848C GND BST SW SW FB/L_IN IN_LDO2 R609 TLE7368-3E OR TLE7368-E GND 1 18 19 36 17 24 9 10 23 C603 100n 13 C604 16 CB601 100n VIN R619 1K5 +5V C601 47µ/50V S601 R625 1K +3V3 +3V3 GND D606 LP T67K R618 680R +3V3 +1V3 D608 +3V3 D609 +5V GND C612 4µ7/10V GND Q_T2 C610 22µ/10V GND C609 22µ/10V +3V3 GND +1V3 X601 POWER VCC_IN D601 X1 1 1 MBRS360T3 Q_T1 +5V 5,5V..50V 2 2 3 2 WDI IN_STBY Q_STBY SEL_STBY MON_STBY /PORST 34 11 2 3 4 25 7 8 31 32 6 30 29 5 28 26 27 33 35 R624 0R_opt +3V3 /PORST C608 1n2 RO_5V 1 GND P1_3 GND GND D604 LS T67K R628 120R 680R R615 GND Q603 BC858C +3V3 /ESR1 /ESR0 1 R640 /PORST P1_15 VDDP /PORST C619 10µF R607 0R 0R_opt R606 GND C606 47µ/10V VSW P1_10 +1V3 0R_opt C607 22µF/10V GND Q601 BDP949 VSW GND R627 10K 0R R610 R641 0R_opt R605 10K +3V3 0R_opt WDO GND GND +5V L601 47µ/3A D602 MBRS340T3 0R +3V3 R639 R638 C605 680n 0R_opt R603 10K R604 +3V3 Q_T1 Q_T2 /ESR0 /PORST 3 2 Q_STBY 4 GND PORT[0..10] PORT[0..10] 5 BST SHDN IN IN GND U603 +5V 0R R614 C620 10µF 121 122 120 20 69 106 154 PORST ESR0 ESR1 VDDP VDDP VDDP VDDP GND V5 7 8 9 10 100n POWER GND GND 5 R608 0R_opt 1 VDD VDD VDD VDD VDD / VDDSB GND GND 153 105 68 10 21 U201A TC1728 GND Q605 SPD09P06PL +5V 100n CB605 100n CB604 100n CB603 GND R644 4K02 C617 10µ/10V +1V3 R643 9K09 0R R642 CB602 /PORST LTC3026EM PG ADJ OUT OUT ONLY IF U601 IS TLE7368-E GND C618 4µ7/10V 5 6 1 2 10µH/150mA L602 R640 MUST BE REMOVED IF U601 IS TLE7368-E /ESR0 4 /ESR1 U601 3 2 3 /ESR0 4 SW GND 3 2 2 155 107 70 22 V5 V5 V5 V5 VPGD 27 VSS HS CB612 100n CB613 100n CB614 100n CB615 100n 3 3 2 8-7 GND +3V3 R612 0R D603 1 GND C621 10µF +1V3 IN U602 TLE4284DV_opt 0R R611 6 GND +1V3 VDDCORE BAT54_opt 3 VDDCORE GND 3 CB611 100n_opt VIN CB610VDDESB 100n 6 ONLY WITH TC1728ED AND ON REQUEST CB606 100n CB607 100n CB608 100n CB609 100n User’s Manual ADJ / GND Figure 8-6 1 1 2 GND C616 10µ/10V_opt VDDESB 7 Sheet: 5 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Supply.sch Infineon Technologies AG TriBoard TC1728 Power supply OUT 7 8 8 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - Power Supply V 1.0, 2011-02 Figure 8-7 User’s Manual 8-8 D C B A NC1[1..80] NC1[1..80] 1 PORT[0..10] NC3[1..80] ADC PORT[0..10] NC3[1..80] BUS EXPANSION 1 VSSM VDDM +3V3 VSSM 2 P1_12 P1_13 P1_14 NC3_77 P0_15 P8_8 P8_10 P8_12 +3V3 VSSM VSSM NC3_42 3 P10_0 P10_1 P10_2 P0_14 P10_3 P8_9 P8_11 P8_13 3 NC3_46 NC3_50 NC3_52 NC3_54 NC3_56 NC3_58 NC3_60 VAGND0 VSSM VDDM AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM NC1_6 NC1_8 NC1_10 NC1_12 NC1_14 NC1_16 NC1_18 NC1_20 NC1_22 NC1_24 NC1_26 NC1_28 NC1_30 NC1_32 NC1_34 NC1_36 NC1_38 NC1_40 NC1_42 NC1_44 NC1_46 NC1_48 NC1_50 NC1_52 NC1_54 NC1_56 NC1_58 NC1_60 NC1_62 NC1_64 NC1_66 NC1_68 NC1_70 NC1_72 NC1_74 NC1_76 NC1_78 NC1_80 GND FTSH-140-02-L-DV-ES-A X703 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FTSH-140-02-L-DV-ES-A_opt X701 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 NOT ASSEMBLED VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 NC3_57 NC3_59 NC3_41 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 NC1_5 NC1_7 NC1_9 NC1_11 NC1_13 NC1_15 NC1_17 NC1_19 NC1_21 NC1_23 NC1_25 NC1_27 NC1_29 NC1_31 NC1_33 NC1_35 NC1_37 NC1_39 NC1_41 NC1_43 NC1_45 NC1_47 NC1_49 NC1_51 NC1_53 NC1_55 NC1_57 NC1_59 NC1_61 NC1_63 NC1_65 NC1_67 NC1_69 NC1_71 NC1_73 NC1_75 NC1_77 NC1_79 2 AN[0..35] AN[0..35] 4 XTAL[1..2] 4 XTAL[1..2] /ESR1 5 5 +3V3 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P2_0 P2_1 P2_2 P2_3 +3V3 VDDESB GND XTAL1 XTAL2 P3_0 P3_1 P3_12 P3_13 P3_2 P3_4 P3_3 NC2_69 P3_10 P0_6 GND NC2_21 NC2_23 P2_8 P2_13 P6_1 P6_0 P6_3 P6_2 NC2_37 NC2_39 P3_5 P3_7 P2_8 P3_8 NC2_9 NC2_11 P0_5 /ESR1 NC2_17 VCC_IN 6 P5_8 P5_9 P5_10 P5_11 P5_12 P5_13 P5_14 P5_15 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 NC4_38 NC4_40 P9_2 P9_3 P9_4 P9_7 P9_8 P8_0 P8_1 P8_2 P1_4 P8_3 P8_4 P8_5 P8_6 P8_7 P2_7 P2_6 P2_5 P2_4 +3V3 GND FTSH-140-02-L-DV-ES-A X704 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4_3 NC2_54 P3_9 P3_8 P3_14 P3_15 P2_11 P2_12 P2_10 NC2_70 P3_11 P0_7 /PORST NC2_24 P2_9 NC2_28 P1_15 P9_5 P9_6 NC2_36 NC2_38 P2_13 P3_6 P2_1 P2_9 P1_10 +3V3 GND GND GND NC2_10 NC2_12 NC2_14 /ESR0 NC2_18 VCC_IN GND FTSH-140-02-L-DV-ES-A X702 PLUG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 6 NC4[1..80] /PORST /ESR0 NC2[1..80] GPTA / MLI Infineon Technologies AG 7 Sheet: 6 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Connectm.sch 8 8 TOP PERIPHERALS TriBoard TC1728 Connectors plug NC4[1..80] NC2[1..80] 7 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - Connectors (Plug) V 1.0, 2011-02 Figure 8-8 User’s Manual 8-9 D C B A NC1[1..80] NC1[1..80] 1 PORT[0..10] NC3[1..80] ADC PORT[0..10] NC3[1..80] BUS EXPANSION 1 VSSM VDDM +3V3 VSSM 2 P1_12 P1_13 P1_14 NC3_77 P0_15 P8_8 P8_10 P8_12 FLE-140-01-G-DV-A X803 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FLE-140-01-G-DV-A_opt X801 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 NOT ASSEMBLED VAGND0 VAREF0 VSSM AN32 AN33 AN34 AN35 NC3_57 NC3_59 NC3_41 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 NC1_5 NC1_7 NC1_9 NC1_11 NC1_13 NC1_15 NC1_17 NC1_19 NC1_21 NC1_23 NC1_25 NC1_27 NC1_29 NC1_31 NC1_33 NC1_35 NC1_37 NC1_39 NC1_41 NC1_43 NC1_45 NC1_47 NC1_49 NC1_51 NC1_53 NC1_55 NC1_57 NC1_59 NC1_61 NC1_63 NC1_65 NC1_67 NC1_69 NC1_71 NC1_73 NC1_75 NC1_77 NC1_79 2 +3V3 VSSM VSSM NC3_42 P10_0 P10_1 P10_2 P0_14 P10_3 P8_9 P8_11 P8_13 3 NC3_46 NC3_50 NC3_52 NC3_54 NC3_56 NC3_58 NC3_60 VAGND0 VSSM VDDM AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 VSSM NC1_6 NC1_8 NC1_10 NC1_12 NC1_14 NC1_16 NC1_18 NC1_20 NC1_22 NC1_24 NC1_26 NC1_28 NC1_30 NC1_32 NC1_34 NC1_36 NC1_38 NC1_40 NC1_42 NC1_44 NC1_46 NC1_48 NC1_50 NC1_52 NC1_54 NC1_56 NC1_58 NC1_60 NC1_62 NC1_64 NC1_66 NC1_68 NC1_70 NC1_72 NC1_74 NC1_76 NC1_78 NC1_80 GND 3 AN[0..35] AN[0..35] 4 XTAL[1..2] 4 XTAL[1..2] /ESR1 5 5 +3V3 P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 P0_7 P0_8 P0_9 P0_10 P0_11 P0_12 P0_13 P0_14 P0_15 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P1_8 P1_9 P1_10 P1_11 P4_0 P4_1 P4_2 P4_3 P2_0 P2_1 P2_2 P2_3 +3V3 VDDESB GND XTAL1 XTAL2 P3_0 P3_1 P3_12 P3_13 P3_2 P3_4 P3_3 NC2_69 P3_10 P0_6 GND NC2_21 NC2_23 P2_8 P2_13 P6_1 P6_0 P6_3 P6_2 NC2_37 NC2_39 P3_5 P3_7 P2_8 P3_8 NC2_9 NC2_11 P0_5 /ESR1 NC2_17 VCC_IN FLE-140-01-G-DV-A X804 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 FLE-140-01-G-DV-A X802 SOCKET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P4_3 NC2_54 P3_9 P3_8 P3_14 P3_15 P2_11 P2_12 P2_10 NC2_70 P3_11 P0_7 /PORST NC2_24 P2_9 NC2_28 P1_15 P9_5 P9_6 NC2_36 NC2_38 P2_13 P3_6 P2_1 P2_9 P1_10 6 P5_8 P5_9 P5_10 P5_11 P5_12 P5_13 P5_14 P5_15 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7 NC4_38 NC4_40 P9_2 P9_3 P9_4 P9_7 P9_8 P8_0 P8_1 P8_2 P1_4 P8_3 P8_4 P8_5 P8_6 P8_7 P2_7 P2_6 P2_5 P2_4 +3V3 GND +3V3 GND GND GND NC2_10 NC2_12 NC2_14 /ESR0 NC2_18 VCC_IN GND 6 NC4[1..80] /PORST /ESR0 NC2[1..80] GPTA / MLI PERIPHERALS Infineon Technologies AG Sheet: 7 of 8 ATV MC ACE PDA Am Campeon 1-12 Number: D-85579 Neubiberg Revision: 1.0 Tel.: +49-89-234-0 Date: 02.08.2010 File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Connectf.sch 7 8 8 BOTTOM TriBoard TC1728 Connectors socket NC4[1..80] NC2[1..80] 7 D C B A TriBoard TC1728 Hardware Manual Schematic and Layout Schematic - Connectors (Socket) V 1.0, 2011-02 T301 R310 CB310 R368 C401 C402 CB405 R404 X402 R318 R327 R324 CB313 L402 R401 C304 R371 C601 R326 CB315 R325 CB311 R311 R369 CB312 R323 R370 R321 R332 C611 C607 R429 R430 1 D402 D403 1 U601 R431 D604 X403 R446 R432 R309 X401 R413 R307 CB401 R317 R314 R434 D501 R602 R639 R453 R209 R607 R641 C610 R601 D605 D606 D607 R379 R372 R439 R433 D502 R454 R511 CB203 R512 L401 R315 R331 D401 CB316 X704 D507 D506 D505 D504 D503 X703 CB610 U201 XT201 R515 R516 R517 R513 R514 D508 R510 CB413 R411 R452 CB614 R615 1 2 3 4 5 6 7 8 R518 1 1 CB207 R231 JP203 CB209 C208 U204 R230 X701 R227 R356 U306 R355 R229 X702 CB204 U202 CB208 R354 R353 CB319 X203 X202 D201 R233 C403 C303 R316 R329 T302 R328 R330 R308 R367 CB309 L601 P301 P302 X601 X201 R450 U302 U303 R640 R312 S601 D203 JP202 U405 U203 R313 R366 CB314 CB601 R603 R621 C602 C604 C608 R322 R622 X301 X302 C603 C207 D202 R234 R228 8-10 R235 D204 JP201 User’s Manual S202 R213 R249 R245 Figure 8-9 R242 8.2 R237 P401 TriBoard TC1728 Hardware Manual Schematic and Layout Layout Component Plot Top Layer V 1.0, 2011-02 D205 S201 R236 R238 R241 R243 R244 R246 R248 R247 C211 R240 C209 C210 C205 R253 R256 R258 R257 R259 Y202 R255 R251 C212 CB206 X802 C206 R252 R620 C202 1 C201 R222 R224 C616 CB608 CB603 R220 R203 CB502 CB607 R219 C619 CB615 CB609 CB613 CB604 C203 R204 R520 R519 R507 CB504 R614 C620 R375 X803 R305 R333 R425 R426 R201 CB611 R342 R438 R617 R339 R619 R618 R501 Q605 R319 R320 R437 R625 R336 R419 U403 R436 R422 R417 R448 R447 CB407 R415 R409 R420 R378 R306 R626 R202 R374 R376 C204 CB606 CB612 R206 R205 CB605 R608 X804 R612 R250 R232 Y201 C621 R225 R226 R207 R611 CB205 R254 1 R505 R223 U602 D603 CB602 R610 R373 R440 R337 CB317 CB318 R343 Q604 U304 Q406 Q404 Q402 Q405 Q403 Q401 R377 R416 R604 R616 R423 1 Q603 R627 R624 R623 Q602 D608 C617 R642 R643 R644 R444 CB418 R456 U402 R451 R455 U404 CB416 R445 C405 CB411 CB404 U401 CB410 R443 U407 CB419 R427 R428 R424 1 R412 R410 R606 R628 R609 U305 R334 R344 C613 CB402 R414 CB408 R421 R449 R435 R418 R338 R335 R340 C612 R605 C614 R638 D602 D609 C618 D601 CB414 R407 CB406 R406 R441 R442 C406 CB409 CB412 R405 C404 R402 R403 U603 U406 CB403 R341 C615 CB417 C605 U408 Y401 CB415 C609 Q601 8-11 L602 User’s Manual C606 X801 TriBoard TC1728 Hardware Manual Schematic and Layout Figure 8-10 Component Plot Bottom Layer V 1.0, 2011-02 R221 R239 ERAY-A P401 R418 DAP R468 CB410 T401 R410 R427 R424 CB413 +5,5V...+50V X502 T402 R529 C404 RST R471 C701 R426 CB415 R425 CB411 R411 R469 CB412 R423 R470 R421 R432 C711 C707 R508 R530 RST D704 P4.0 P4.1 P4.2 P4.3 P4.4 P4.5 P4.6 P4.7 +VDD D705 6299.213 (mil) GND 4840 (mil) 1 X803 CB733 1 1 R708 R741 C710 U101 1 2 3 4 5 6 7 8 R618 BOOTCONFIG 1 1 R702 R707 R739 +3V3 R701 +5V D706 CB735 CB713 XT301 R615 R616 R617 R613 R614 D707 R309 R539 R310 R533 R534 D601 1 U701 R531 R412 1 R408 R532 R409 OCDS1 R501 ACT R504 X501 X503 A1 D603 CB501 POWER ERAY-B CB505 D503 D604 C501 C502 1 D502 X804 D605 1 D602 R611 L501 R407 D606 L502 S701 D607 U505 R428 R431 R612 CB303 D608 R610 USB CB720 CB721 CB210 CB211 R204 GND U201 U203 X801 2280 (mil) R229 CB201 R220 P501 R415 R417 R414 R429 R430 CB416 L1 P402 X701 R101 C503 R416RUN C403 R467 CB409 L701 S301 R623 CB222 CB202 CB209 CB212 R222 R223 CB221 R224 CB207 R102 CB203 R205 R209 R456 U406 R455 CB220 CB219 2280 (mil) X802 R454 R453 CB419 U204 U202 R228 CB223 CB513 D501 U402 U403 R740 CB206 CB205 CB217 R219 R221 R212 R210 R208 R207 R206 CB214 CB224 CB204 CB218 R511 R413 R466 CB414 CB701 R703 R721 C702 C704 C708 R422 R722 X401 X402 C703 CB743 CB742 CB732 R712 ETK R625 8-12 CAN1 CB213 CAN0 CB208 1 CB215 A1 CB216 1 1 TriBoard-TC1798 V1.0 User’s Manual X805 GND 287.315 (mil) 1 8.3 1 4900 (mil) TriBoard TC1728 Hardware Manual Schematic and Layout Layout with Dimensioning The following dimensions should be used for development of extension boards. Note: these are the pictures from the TriBoard TC1798. Connectors X801...X804 are on the same place. Figure 8-11 Dimensioning (mil) V 1.0, 2011-02 989.764 (mil) 3367 (mil) 3937.008 (mil) ERAY-A P401 +5,5V...+50V X502 R418 DAP R468 CB410 T401 R410 R427 R424 CB413 POWER ERAY-B CB505 T402 C404 RST R471 C701 R426 CB415 R425 CB411 R411 R469 CB412 R423 R470 R421 R432 C711 C707 R529 R530 R508 D503 X503 A1 RST D704 P4.0 P4.1 P4.2 P4.3 P4.4 P4.5 P4.6 P4.7 R534 D601 +VDD D705 160 (mm) GND CB211 R204 GND CB210 122.936 (mm) 1 X803 CB733 1 R708 R741 C710 U101 BOOTCONFIG 1 2 3 4 5 6 7 8 R618 1 1 1 R702 R707 R739 +3V3 R701 +5V D706 CB735 CB713 XT301 R615 R616 R617 R613 R614 D707 R309 R539 R310 R533 D603 1 U701 R531 R412 1 R408 R532 R409 OCDS1 R501 ACT R504 X501 D502 X804 D604 1 1 D605 C501 C502 R407 D606 L502 S701 D607 CB501 R417 D602 R611 L501 R415 R428 R431 R612 CB303 D608 R610 U505 CB720 CB721 U201 U203 X801 R229 CB201 R220 P501 USB R416RUN C403 CB416 L1 P402 X701 R101 C503 D501 U402 U403 R414 R429 R430 S301 R623 CB222 CB202 CB209 CB212 R222 R223 CB221 R224 CB207 R102 CB203 R205 R209 R456 U406 R455 CB220 CB219 57.912 (mm) X802 R454 R453 CB419 U204 U202 R228 CB223 CB513 R467 CB409 L701 CB205 CB206 CB217 R219 R221 R212 R210 R208 R207 R206 CB214 CB224 CB204 CB218 R511 R413 R466 CB414 CB701 R703 R740 R721 C702 C704 C708 R422 R722 X401 X402 C703 CB743 CB742 CB732 8-13 R712 ETK R625 CAN1 CB213 CAN0 CB208 1 CB215 A1 CB216 1 1 TriBoard-TC1798 V1.0 57.912 (mm) X805 GND 7.2978 (mm) 1 User’s Manual 1 124.46 (mm) TriBoard TC1728 Hardware Manual Schematic and Layout Figure 8-12 Dimensioning (mm) V 1.0, 2011-02 25.14 (mm) 85.5218 (mm) 100 (mm) TriBoard TC1728 Hardware Manual Keyword Index A ACTIV LED 3-2 Assembly Options 4-3 C CAN connector pinout 7-5 Clock 3-1 Clock Signals 6-2 Connector for TC1728 7-2 Connector Pin Assignment 7-1 CPU clock 3-1 Crystal oscillator 3-1 D DAP 3-4 DAP connector pinout 7-5 Debug Signals 6-2 Debug System 3-4 Dimensioning 8-12 E External clock 3-1 F Flexray Pinout 7-4 G General optional resistors 4-3 H HW Boot Configuration 4-1 HWCFG 4-1 I Interrupt Signals 6-1 L Layout 8-10 LEDs 3-1 Location of general optional resistors on User’s Manual Bottom Side 4-4 Location of general optional resistors on Top Side 4-4 Location of peripheral resistors on Bottom Side 4-6 Location of peripheral resistors on Top Side 4-5 Location of resistors for safety device on Bottom Side 4-7 M manual reset 3-1 miniWiggler JDS 3-2 MultiCAN 3-3 O OCDS connector pinout 7-5 OCDS1 3-4 oscillator circuit 3-1 Other peripherals 3-3 P Peripheral Signals 6-2 Power connector pinout 7-4 Power Signals 6-1 power supply 3-1 R reset 3-1 Reset Signals 6-1 Resistors for peripherals 4-5 Resistors for safety device 4-6 RUN LED 3-2 S Safety device Signals 6-4 Safety option 3-3 Samtec 7-1 Schematic 8-1 Schematic and Layout 8-1 Serial Connection to PC 3-2 L-1 V 1.0, 2011-02 TriBoard TC1728 Hardware Manual Serial EEPROM 3-3 Serial Eeprom 3-3 Signal Description 6-1 Software 5-1 status LED 3-4 Supply 3-1 T Toggle LED’s 3-4 TriBoard Software 5-1 TriBoard TC1728 V1.0 Placement 2-4 Type of Boot TC1728 4-1 U USB Connector 3-2 USB connector pinout 7-4 User’s Manual L-2 V 1.0, 2011-02 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG