advertisement LT1777 High Voltage, Low Noise Buck Switching Regulator Design Note 212 Ajmal Godil The LT®1777 is a wide input range buck (step-down) switching regulator specially designed for low noise applications. The LT1777 can be beneficial in applications where low noise is critical, such as telecom, automotive cellular and GPS receiver power supplies. The schematic in Figure 1 highlights the capabilities of the LT1777. VSW NODE VOLTAGE 10V/DIV SWITCH CURRENT 200mA/DIV The LT1777 can accept input voltages from 7.4V to 48V and has a nominal switching frequency of 100kHz. The monolithic die includes an onboard 700mA peak current switch, oscillator, control and protection circuitry. It uses current mode control that delivers excellent dynamic input supply rejection and short-circuit protection. In order to achieve low noise, the LT1777 is equipped with dI/dt limiting circuitry that is programmed via a small inductor (LSENSE in Figure 1) in the power path. It also contains internal circuitry to limit dV/dt during switch turn-on and turn-off. Figure 2 shows the VSW node voltage and switch current for the low noise LT1777. Figure 3 shows the VSW node voltage and switch current for the high voltage LT1676 buck regulator under the same test conditions (no slew rate limiting). It can be seen from Figures 2 and 3 that the switch node voltage and current waveforms for the LT1777 are more controlled and rise and fall more slowly than those of the LT1676 regulator. Conducted and radiated EMI are dramatically reduced by slowing down the sharp edges during turn-on and turn-off of VIN 7.4V TO 48V + C4 100μF 63V 10 12 3 14 R4 68k C3 100pF C6 100pF C7 680pF 2 11 15 7 VIN VCC SHDN VC U1 LT1777 VSW VD FB NC GND NC GND NC GND SGND Figure 2. VSW Voltage and Switch Current for the LT1777 VSW NODE VOLTAGE 10V/DIV SWITCH CURRENT 200mA/DIV GND DN212 F03 500ns/DIV Figure 3. VSW Voltage and Switch Current for the LT1676 (No Slew Control) L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. LSENSE 0.47μH SML32-470k 4 SYNC DN212 F02 500ns/DIV 6 L1 200μH BH 510-1043 OR CTX200-4 + 5 13 1 D1 MBRS1100 C2 100μF 10V C1 1μF 10V VOUT 5V 500mA R3 36.5k 1% 8 9 16 R1 21.1k 1% DN212 F01 Figure 1. 100kHz Low Noise Step-Down Switching Regulator 09/99/212_conv the power switch with only modest reduction in conversion efficiency. Figure 4 shows a spectral analysis of the current wave forms for the LT1777 and the LT1676. The horizontal axis is 2MHz/DIV (0MHz to 20MHz), and the vertical axis is 10dB/DIV. It can be seen from Figure 4, the LT1777 attenuates the high frequency noise by approximately –20dB compared to the LT1676. The LT1777 can be disabled by connecting the shutdown (SHDN) pin to ground, reducing input current to a few microamperes. For normal operation, decouple the SHDN pin with a 100pF capacitor to ground. The part also has a SYNC pin, used to synchronize the internal oscillator to an external clock, which can range from 130kHz to 250kHz. To use the part’s internal oscillator, simply connect the SYNC pin to ground. Since the LT1777 allows such a wide input range, the internal control circuitry draws power from the VCC pin, which is normally connected to the output supply. During start-up, the LT1777 draws power from VIN; after the switching supply output reaches 2.9V, the LT1777 uses the output voltage to power its internal control circuitry, thereby reducing quiescent power by hundreds of milliwatts when operating at high line voltages. Figure 5 shows a typical efficiency curve for the LT1777 using sense inductor, LSENSE = 0.47μH, VIN = 12V and VOUT = 5V. Generating Low Noise, Dual-Voltage Supplies The circuit in Figure 6 shows a cost-effective way to generate 5V and –5V low noise supplies from a single 10V to 28V supply using the LT1777 and a few off-theshelf components. L1A and L1B are two windings on a single core, used to generate ±5V. To minimize coupling mismatches between the two windings, C2 has been added, forcing the winding potentials to be equal and improving cross regulation. Total available current from both outputs is limited to 500mA. Maximum negative suppy current is affected by the postitive 5V load; a typical limit is one-half of the positive current. 85 EFFICIENCY (%) 80 10dB/DIV 75 70 65 VIN = 12V VOUT = 5V LSENSE = 0.47μH DN212 F04 2MHz/DIV 60 Figure 4. Spectral Analysis of the Waveforms for the LT1676 and the Low Noise LT1777 100 0 300 400 200 LOAD CURRENT (mA) 500 DC242 F05 + C6 100μF 63V 4 10 100pF C4 100pF R3 22k VCC VIN VSW L1B 200μH 6 C3 100μF 10V 5 VD 13 SHDN FB LT1777 14 1 VC GND 8 GND 12 9 SYNC GND 7 12 SGND GND 3 SHDN LSENSE 0.47μH D1 MBRS1100 C2 4.7μF + L1A 200μH C5 2200pF + C1 1μF 10V D2 MBRS1100 C8 1μF 10V VOUT 5V R1 36.5k 1% L1A/B: COILTRONICS CTX200-4 OR BH ELECTRONICS 510-1043 LSENSE: GOWANDA SML32-470K R2 12.1k 1% + VIN 10V TO 28V Figure 5. LT1777 Output Efficiency –VOUT –5V C7 100μF 10V DN212 F06 Figure 6. This Cost-Effective Supply Generates ±5V from a 10V to 28V Input Data Sheet Download www.linear.com Linear Technology Corporation For applications help, call (408) 432-1900 dn212f_conv LT/TP 0999 340K • PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 1999