1W SMD DC-DC Converter P1FS-Series ● ● ● ● ● ● SMD package Single output and dual output versions Up to 3000 VDC isolation MTBF > 3,500,000 h at 25°C -40...85°C operating temperature range Efficiency up to 79 % Model guide Model Single output P1FS3R33R3S P1FS3R305S P1FS0505S P1FS0509S P1FS0512S P1FS0515S P1FS123R3S P1FS1205S P1FS1209S P1FS1212S P1FS1215S P1FS2405S P1FS2412S P1FS2415S P1FS2424S Dual output P1FS3R312D P1FS0505D P1FS0509D P1FS0512D P1FS0515D P1FS1205D P1FS1209D P1FS1212D P1FS1215D P1FS2405D P1FS2412D Input voltage range Output voltage [VDC] [VDC] min. [mA] 3..3.6 3..3.6 4.5..5.5 4.5..5.5 4.5..5.5 4.5..5.5 10.8..13.2 10.8..13.2 10.8..13.2 10.8..13.2 10.8..13.2 21.6..26.4 21.6..26.4 21.6..26.4 21.6..26.4 3.3 5.0 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 5.0 12.0 15.0 24.0 2.97..3.63 4.5..5.5 4.5..5.5 4.5..5.5 4.5..5.5 10.8..13.2 10.8..13.2 10.8..13.2 10.8..13.2 21.6..26.4 21.6..26.4 ±12.0 ±5.0 ±9.0 ±12.0 ±15.0 ±5.0 ±9.0 ±12.0 ±15.0 ±5.0 ±12.0 Part designation structure Output power Series designation P1 1W F Mounting technology S SMD Efficiency typ. Capacitive load max. max. [mA] Output reflected ripple & noise [mVp-p] [%] [µF] 30 20 20 11 9 7 30 20 11 9 7 20 9 7 5 304 200 200 110 84 66 303 200 110 84 66 200 84 66 42 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 75..100 73 75 70 76 78 79 70 69 73 73 74 69 77 74 76 10 10 10 4.7 2.2 1 1 10 4.7 2.2 1 10 2.2 1 0.47 ±5 ±10 ±6 ±5 ±4 ±10 ±6 ±5 ±4 ±10 ±5 ±42 ±100 ±55 ±42 ±33 ±100 ±55 ±42 ±33 ±100 ±42 50..75 50..75 50..75 50..75 50..75 50..75 50..75 50..75 50..75 50..75 50..75 77 71 77 78 79 71 73 74 75 70 77 2x1 2 x 4.7 2 x 2.2 2x1 2x1 2 x 4.7 2 x 2.2 2x1 2x1 2 x 4.7 2x1 Output current Input voltage Output voltage 3R3 05 12 24 3R3 05 09 12 15 24 3.3 V 5V 12 V 24 V 3.3 V 5V 9V 12 V 15 V 24 V Output configuration D dual S single Packing blank TR Tube Reel Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1FS-Series Specifications Input Voltage range Filter Input / output: Isolation voltage tested for 60 sec. @ leakage current < 1mA Isolation resistance @ 500 VDC Capacitance Output Output voltage drift @ 3.3V Vout models Output voltage drift @ all other models Output voltage drift @ 10 % to 100 % load change 3.3 V output version 5 V output version 9 V output version 12 V output version 15 V output version 24 V output version Temperature coefficient Short circuit duration General Switching frequency Environmental Operating temperature (ambient) Case temperature Storage temperature Derating Cooling Case temperature rise at full load Humidity ± 10 % of nominal Capacitors 3 kVDC 109 Ω, min. 30 pF, typ. 100 pF, typ. @ P1FS2424Dx ± 1.5 % @ 1% Vin change ± 1.2 % @ 1% Vin change 15 % typ., 20 % max. 12.8 % typ., 15 % max. 8.3 % typ., 10 % max. 6.8 % typ., 10 % max. 6.3 % typ., 10 % max. 6 % typ., 10 % max. 0.03 % / °C, max., at full load 1 sec., max. ~ 100 kHz, 3.3, 5, 12 Vin Types ~ 500 kHz, 24 Vin Types Physical Package material Weight Reliability, MTBF (MIL-HDBK-217 @ 25 °C) Absolute maximum ratings Vin 3.3 V types Vin 5 V types Vin 12 V types Vin 15 V types Vin 24 V types Manual soldering lead temperature Soldering temperature Moisture sensitivity level (MSL) -40 °C to +85 °C 95 °C, max. -55 °C to +125 °C None required Free-air convection 15…25 °C Up to 95 %, non-condensing Epoxy resin (UL94-V0) 1.71 g 3.5 Mio. hours -0.7 ~ 5 VDC, max. 1 s -0.7 ~ 9 VDC, max. 1 s -0.7 ~ 15 VDC, max. 1 s -0.7 ~ 21 VDC, max. 1 s -0.7 ~ 30 VDC, max. 1 s 300 °C max. 10 s max., 1.5 mm distance from body 217 °C for 60 s max., 245 °C peak IPC/JEDEC J-STD-020D.1 Fig. 1 External circuit to decreace the input and output ripple & noise + Vin L L + Vout + Vin L L + Vout Cout Com Cin - Vin Cin Cout Cout - Vout - Vin L - Vout Table 1 Filter components to figure 1 Input components Vin version Cin L 3.3 V 4.7 µF, 50 V 6.8 µH 5V 4.7 µF, 50 V 6.8 µH 12 V 2.2 µF, 50 V 6.8 µH 24 V 1 µF, 50 V 6.8 µH Output components Vout version Cout L 3.3 V 10 µF, 50 V 6.8 µH 5V 10 µF, 50 V 6.8 µH 9V 4.7 µF, 50 V 6.8 µH 12 V 2.2 µF, 50 V 6.8 µH 15 V 1 µF, 50 V 6.8 µH 24 V 1 µF, 50 V 6.8 µH ±3.3 V 4.7 µF, 50 V 6.8 µH ±5 V 4.7 µF, 50 V 6.8 µH ±9 V 2.2 µF, 50 V 6.8 µH ±12 V 1 µF, 50 V 6.8 µH ±15V 1 µF, 50 V 6.8 µH It’s not recommended to connect any external capacitor in the application field with less than 0.5 watt output load. Page 2 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1FS-Series Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1FS-Series Application note 1) Requirement on output load To ensure this module can operate efficiently and reliably during operation, the minimum output load must be higher than 10% of the full load. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output power. Operation with smaller load than minimum load will not damage the converter. However, they may not meet all specification listed, and that will reduce the life time of product. 2) Recommended testing circuit If you want to further decrease the input / output ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a start up problem might arise. To ensure safe and reliable operation, the capacitance of the output filter for each output channel may not exceed certain values (see Table 1 on page 2). 3) Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over voltage and over current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series. 4) Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self recovery fuse in series at the input end or add a circuit breaker to the circuit. 5) No parallel connection or plug and play ! Dimensions Lead 1 2 3 4 5 6 7 8 9 10 11 12 Single output version - Vinput + Vinput Not connected No Pin - Voutput Not connected Not connected + Voutput No Pin Not connected Not connected Not connected Dual output version - Vinput + Vinput Not connected No Pin common output - Voutput Not connected + Voutput No Pin Not connected Not connected Not connected Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1FS-Series Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 06.14 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]