5W AC-DC Power-Supply PAC5B ● ● ● ● ● 85 … 264 VAC / 100 … 400 VDC universal input Continuously short circuit and over current protected Isolation class II MTBF > 300000 hours Small outlines Model guide Type PAC5B03S PAC5B05S PAC5B09S PAC5B12S PAC5B15S PAC5B24S Output voltage Output current range Ripple & noise up to Efficiency typ.@ full 20 MHz load, Vin 230 VAC Accuracy min. max. [mVp-p] max. [%] typ. [VDC] [%] [mA] [mA] 3.3 ±3 100 1000 150 65 5.0 ±2 100 1000 150 70 9.0 ±2 56 560 150 72 12 ±2 42 420 150 74 15 ±2 34 340 150 75 24 ±2 21 210 150 75 Capacitive load [µF] max. 2200 1500 680 470 330 100 Specifications Input Voltage range Frequency Full load input current Inrush current Standby power Recommended fuse Hold up time Isolation Isolation voltage (input to output) Isolation resistance Leakage current Output Minimum load Line regulation Load regulation @ 10 to 100% load change Temperature coefficient EMI 85..264 VAC or 100..400 VDC Power derating see diagram 47 .. 440 Hz 200 mA max @ 115 VAC 100 mA max @ 230 VAC 20 A @ 115 VAC 30 A @ 230 VAC 0.5 W, max. 1 A / 250 V slow blow 20 ms min. @ 115 VAC 80 ms min. @ 230 VAC 3000 VAC (1 minute, <5 mA) 100 MΩ 0.25 mA @ CY 1 nF / 400V 10 % ± 0.5 %, max. ± 1.5 %, max. 0.02 % / °C Conducted emission Radiation emission ESD Electrostatic discharge RS field susceptibility EFT Fast transients on mains line EMC EMS Surge CS PFM Voltage dips, short and interruptions immunity Protection Short circuit Over current Over temperature General Reliability MTBF@ 25°C Switching frequency Environmental Operating temperature (ambient) Power derating Storage temperature Case surface temperature Storage humidity Cooling Safety approvals Physical Dimensions Weight Case material Mounting Soldering temperature, Time Continuous, auto recovery 110 % of full load No >300000 h ~100 kHz -40 °C to +85 °C (with derating, see diagram) see diagram -40 °C to +105 °C 100 °C, max. 85 %, max. Free air convection EN60950, UL60950 42 x 27 x 11 mm 10 g UL94V-0 On PCB Wave 265 °C max., 10 s max. Manual 370 °C max., 5 s max. EN55022 (CISPR22), class A (External circuit refer to fig. 2) EN55022 (CISPR22), class B (External circuit refer to fig. 3) EN55022 (CISPR22), class B (External circuit refer to fig. 2 and 3) IEC, EN61000-4-2, contact ± 4 kV perf. criteria B IEC, EN61000-4-3, 10 V/m perf. criteria A (External circuit refer to fig. 3) IEC, EN61000-4-4, ± 2 kV, perf. criteria B (External circuit refer to fig. 2) IEC, EN61000-4-4, ± 4 kV, perf. criteria B (External circuit refer to fig. 3) IEC, EN61000-4-5, ± 1 kV perf. criteria B (External circuit refer to fig. 3) IEC, EN61000-4-5, ± 2 kV perf. criteria B (External circuit refer to fig. 3) IEC, EN61000-4-6, 3 Vrms perf. criteria A (External circuit refer to fig. 3) IEC, EN61000-4-8, 10 A/m perf. criteria A IEC, EN61000-4-11, 0…70 % perf. criteria B 1. External electrolytic capacitors are required to models. More details refer to typical applications. 2. Ripple and noise were measured refer to “ripple and noise measure configuration”. 3. All specifications were measured at Ta 25 °C, humidity <75 %, nominal input voltage (115 VAC or 230 VAC) and rated output load unless otherwise specified. 4. In this datasheet, all the test methods of indications are based on corporate standards. 5. In applications with high vibration, the product need to be glued for fixing. Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 5W AC-DC Power-Supply PAC5B Functional diagram Vin (N) Vin (L) 1 Input rectifier 3 14 + Vout Output rectifier & filter DC/DCConverter 12 - Vout 5 C1 External capacitor 7 Application note inadmissible connection PAC5B N +Vout -Vout L PE This connection is not supported for the PAC5B series! Ripple and noise measure configuration PAC5B N L1 C3 C4 Load 14 +Vo 1 F1 L C2 Measure points for oscilloscope probe -Vo 12 3 7 C1 5 CY Figure 2 EMC application circuit for standard requirement, Class A PAC5B N L C2 F1 NTC MOV U L1 C3 D1 C4 +Vout -Vout CX C1 CY For standard EMC requirement, please refer to figure 2, recommended parameters are shown in this table. Type F1 MOV NTC L1 CY C1 C2 C3 PAC5B03S 120 µF 0.47 µH 470µF PAC5B05S 1A 22 µF, PAC5B09S 250V Type Type 1 nF, 68 µF 400 V slow S14K350 5D-9 400 VAC 1 µH PAC5B12S 35 V 330 µF blow PAC5B15S 100 µF PAC5B24S 4.7 µH C4 D1 SMBJ7.0A 0.1 µF 50 V ceramic SMBJ12A SMBJ20A SMBJ30A Page 2 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 5W AC-DC Power-Supply PAC5B Recommend PCB layout Linewidth ≥3 mm, line to line distance ≥6 mm, line ground distance ≥6mm, undefined unit: mm Figure 3, EMC application circuit for applications with higher EMC requirement, Class B Complete input filter module PN: PIF003A PAC5BxxS L F1 L LDM C2 CY MOV2 U CX L1 C3 D1 C4 +Vout + Rd -Vout CY N N LCM PE C1 CY For higher EMC requirement, please refer to figure 3, recommended parameters are shown in this table. Type F1 Filter module CY CX C1 C2 C3 PAC5B03S 120 µF 470 µF PAC5B05S 0.1 µF, 22 µF, PAC5B09S 1 A, 250 V 1 nF, PIF003A 68 µF 275 VAC 400 V slow blow 400 VAC PAC5B12S 35 V 330 µF PAC5B15S 100 µF PAC5B24S C4 D1 SMBJ7.0A 0.1 µF 50 V ceramic SMBJ12A SMBJ20A SMBJ30A Note: C1, C2 and C3 are electrolytic capacitors. They are required both AC input and DC input. When AC input, C1 is used as filter capacitor, the value of C1 is recommended to be 22 μF / 400 V. When DC input, C1 is used as EMC filter capacitor, the value of C1 is recommended to be 10 μF / 400 V (when the input voltage is above 370 VDC, the recommended value of C1 is 10 μF / 450 V). C2 and C3 are output filter capacitors, they are recommended to be high frequency and low impedance electrolytic capacitors. Capacitance and rated ripple current of capacitors refer to the data sheets provided by the manufactures. Voltage derating of capacitors should be 80 % or above. C4 is a ceramic capacitor, which is used to filter high frequency noise. C2, C3 and L1 form a pi-type filter circuit. Current of L1 refer to the datas heets provided by the manufactures, current derating should be 80% or above. TVS diode is a recommended component to protect post-circuits (if converter fails). External input NTC is recommended to use 5D-9. External input MOV1 is recommended to use S14K350. Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 5W AC-DC Power-Supply PAC5B Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 5W AC-DC Power-Supply PAC5B Dimensions Pin 1 3 5 7 12 14 Pin connections Function AC In (N) or -Vin AC In (L) or +Vin + Capacitor (C1) - Capacitor (C1) - DC Out + DC Out Unit in mm Pin section tolerance ± 0.1 mm General tolerances ± 0.5 mm PHI-CON is a trademark of HY-LINE Power Components. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 04.14 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]