60W DC-DC Converter P60A-Series ● ● ● ● ● ● ● ● ● ● ● ● ● ● Wide 2:1 input range Efficiency up to 92% Adjustable output voltage Remote control on/off 1600 VDC isolation Continuous short circuit protection Over voltage protection Over current protection Over Temperature protection Under voltage lockout Soft start function Standard package 2” x 2” x 0.4” Output with sense feedback -40...+85°C operating temperature range with derating Model selection guide Type Input nominal voltage [VDC] Single output P60A243R3S P60A2405S P60A2412S P60A2415S P60A483R3S P60A4805S P60A4812S P60A4815S 18...36 18...36 18...36 18...36 36...75 36...75 36...75 36...75 Input current no load full load [mA] 80 100 40 40 50 60 40 40 [mA] 2150 2760 2800 2800 1075 1390 1400 1400 Output voltage Output current Ripple & noise *3 Z-Diode output protection Efficiency typ. @ full load Capacitive load *4 [VDC] [A] [mVpk-pk] [VDC] [%] [µF] 0...14 0...12 0...5 0...4 0...14 0...12 0...5 0...4 75 75 100 100 75 75 100 100 3.9 6.2 15 18 3.9 6.2 15 18 91 92 91 91 91 92 91 91 33000 20000 3300 2200 33000 20000 3300 2200 3.3 5.0 12.0 15.0 3.3 5.0 12.0 15.0 Application example for single output version + INPUT C1 + 220µF < 90 mΩ L 12µH C2 1µF 100V The output voltage can be externally trimmed by using the method shown below. ( ) for dual output trim 1 6 Remote ON 5 +SENSE 3 DC/DC - Converter P60Axxxxx Remote OFF + OUTPUT R - Trim down 8 C-load See table 4 -SENSE R - Trim up - OUTPUT - INPUT 7 2 1. For the Single output: Maximum output deviation is 10 % inclusive of remote sense and trim. If remote sense is not being used, the + SENSE should be connected to it’s corresponding +OUTPUT and likewise the - SENSE should be connected to its corresponding -OUTPUT. 2. One load is 25 % to 100 % load, the other load is 100 % load, the output voltage variable rate is within ± 5 %. 3. Measured with 20 MHz bandwidth and 1.0 µF ceramic capacitor. 4. Tested by minimal Vin and constant resistive load. 5. Tested by normal Vin and 25 % load step change ( 75 %-50 %-25 % of full load ). 6. Measured Input reflected ripple current with a simulated source inductance of 12 µH. 7. The remote on / off control pin is referenced to –Vin (pin 2). 8. The P60B-series can meet EN55022 Class A with an external filter in parallel with the input pins . 9. An external filter capacitor is required if the module has to meet EN61000-4-4 and EN61000-4-5. The filter capacitor PHI-CON suggest: NIPPON CHEMI-CONs KY - series, 220 µF / 100V. 10. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating! Page 1 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 60W DC-DC Converter P60A-Series Specifications Input Under Voltage lockout Vin 24V types Vin 48V types Filter Reflected ripple current *6 Remote control levels *7 On Off Off input idle current Isolation: Rated voltage (tested for 3 s) Resistance Capacitance Output Voltage accuracy Output voltage trim range Voltage cross balance (dual outputs) *2 Line voltage regulation Load voltage regulation single Load voltage regulation dual Temperature coefficient Transient recovery time *5 Transient response deviation *5 Short circuit protection Over load protection Short circuit restart on @ 17.8 VDC, off @ 16 VDC on @ 33.5 VDC, off @ 30.5VDC π - type 20 mAp-p, typ. 3~12 VDC or open input 0~1.2 VDC 5 mA, typ. 1600 VDC 9 10 Ω 2500 pF, typ. ±1% ± 10 % ±5 % @ 25 % / 100 % of load ± 0.5 % ± 0.5 % @ 0 %...100 % load ± 1 % @ 1 %...100 % load ± 0.02 % / °C 250 µs, typ 3% Continuous, hiccup 130 % of full load, typ. Automatic General Start up time Switching frequency Safety standard in accordance with Reliability Calculated MBTF EMC characteristics Radiated emissions Conducted emissions *8 ESD RS EFT *9 Surge *9 CS PFMF Environmental Operating temperatur (ambient) Case temperature Storage temperature Over temp. protection Humidity Cooling Physical Dimensions Weight Case material Potting Material Absolute max. ratings *10 Pin soldering temperature 1.5 mm distance from body Max. input voltage for 0.1s Vin 24 V types Vin 48 V types 20 ms @ R-load 270 kHz, typ. IEC / EN 60950-1 >110000 hrs EN55022 Class A EN55022 Class A EN61000-4-2 pref criteria A EN61000-4-3 pref criteria A EN61000-4-4 pref criteria A EN61000-4-5 pref criteria A EN61000-4-6 pref criteria A EN61000-4-8 pref criteria A -40 °C to +85 °C with derating -40 °C to +40 °C full load 110 °C, max. -40 °C to +125 °C t-case 120 °C, typ Up to 95 %, non-condensing Free-air convection 50.80 x 50.80 x 10.16 mm 70 g Nickel-coated brass Epoxy (UL94V-0 rated) 260°C for 10 sec -0.7~50 VDC -0.7~100 VDC Efficiency vias load change Page 2 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 60W DC-DC Converter P60A-Series Dimensions Pin configuration Pin 1 2 3 4 5 6 7 8 Single + Vin - Vin Rem ctrl - Sense + Sense + Vout - Vout Trim Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 9 / 12f Page 3 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]