SIDACtor ® Protection Thyristors High Surge Current Protection 5kA Series - TO-218 Pb e3 RoHS Description The 5kA Series are SIDACtor® components designed to protect equipment located in high exposure environments from severe overvoltage transients. Packaged in a robust TO-218 package, the 5kA Series is ideal for use in data interface and AC power line for CATV amplifiers, Telecom Base Station equipment and Cell Towers. Features and Benefits • Low voltage overshoot • Rugged TO-218 package • Low on-state voltage Agency Approvals Agency • 5000A 8/20 µs surge rating • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 • 2nd level interconnect is Pb-free per IPC/ JEDEC J-STD-609A • Fails short circuit when surged in excess of rating Pinout Designation 2 • RoHS compliant, leadfree and halogen-free Applicable Global Standards 1 2 3 (No Connection) Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21/.45 Enhanced Level • YD/T 1082 • ITU K.20/21/.45 Basic Level • YD/T 950 • YD/T 993 • GR 1089 Inter-building 1 2 Additional Information Datasheet Resources Samples Electrical Characteristics Part Number P1500MEL Marking P1500ME VDRM @lDRM=5µA VS @100V/µs V min V max 140 180 IH IS IT mA min mA max A max 50 800 2.2/25 VT @IT=2.2 A Capacitance @1MHz, 2V bias V max pF min pF max 4 400 650 P1900MEL P1900ME 155 220 50 800 2.2/25 4 400 650 P2300MEL P2300ME 180 260 50 800 2.2/25 4 350 600 P3800MEL P3800ME 350 430 50 800 2.2/25 4 300 500 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - IT is a free air rating and heat sink is at 25A © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/04/15 SIDACtor ® Protection Thyristors High Surge Current Protection Surge Ratings IPP Series ITSM 50 / 60 Hz di/dt A min A min A/µs max 5000 400 630 8/20 1.2/50 1 E 2 3 Notes: 1 Current waveform in µs 2 Voltage waveform in µs 3. For surge rating of P3800MEL, it is minimum 4kA and typical 5kA @8/20µs. - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Conditions Package Symbol Parameter Value Unit TJØ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C TC Maximum Case Temperature 100 °C R0JC* Thermal Resistance: Junction to Case 1.7 °C/W R0JA Thermal Resistance: Junction to Ambient 56 °C/W TO-218 2 1 2 3 (No Connection) *R0JC rating assumes the use of a heat sink and on state mode for extended time at 25 A, with average power dissipation of 29 W. V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/04/15 SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C TP tP Critical Zone TL to TP Ramp-up TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material Figure 1 Temperature Reflow Condition UL recognized epoxy meeting flammability classification V-0 High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Part Marking Part Numbering P xxx 0 ME L TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/04/15 RoHS COMPLIANT IPP RATING XXXXXXX xxxxx Part Number Code (Refer to Electrical Characteristics Table) Date Code SIDACtor ® Protection Thyristors High Surge Current Protection Dimensions — TO-218 TC Measurement Point U DIA. B A Tab is connected to PIN 2 F E Dimensions C D W PIN 3 J P PIN 1 M Q PIN 2 R H G N 3 Times K L Notes: • • • • Mold flash shall not exceed 0.13 mm per side. Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Pin 3 has no connection. Tab is non-isolated (connects to middle pin). A B C D E F G H J K L M N P R U W Inches Millimeters Min Max Min Max 0.810 0.610 0.178 0.055 0.487 0.635 0.022 0.075 0.575 0.211 0.422 0.058 0.045 0.095 0.008 0.161 0.085 0.835 0.630 0.188 0.070 0.497 0.655 0.029 0.095 0.625 0.219 0.437 0.068 0.055 0.115 0.016 0.165 0.095 20.57 15.49 4.52 1.40 12.37 16.13 0.56 1.91 14.61 5.36 10.72 1,47 1.14 2.41 0.20 4.1 2.17 21.21 16.00 4.78 1.78 12.62 16.64 0.74 2.41 15.88 5.56 11.10 6.73 1.40 2.92 0.41 4.2 2.42 Packing Options Package Type M Description Packing Options Quantity Added Suffix Industry Standard TO-218 (ME) Tube Pack 250(25 per tube/10 tubes per box) N/A N/A TO-218 Tube Pack Specification Tube Pack Specification — TO-218 NOTES: (UNLESS OTHERWISE SPECIFIED) 1. 2. 3. 4. 5. 6. 7. INSIDE RADIUS: 1.3 MAX. TOLERANCES: +/- 0.25 MATERIAL: TRANSPARENT AND RIGID PVC TINT: CLEAR ANTISTATIC: YES TUBE CAPACITY:P 25 DEVICES TUBE WARPAGE NOT TO EXCEED: 0.08 PER 25.4 OR 1.5 END TO END 8. MAX. BURR ALLOWED ON INSIDE SURFACES 0.13 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/04/15