ISL54208 ® Data Sheet December 18, 2006 Low Voltage, Dual SPDT, USB/CVBS/ Audio Switches, with Negative Signal Capability FN6410.0 Features • High Speed (480Mbps) Signaling Capability per USB 2.0 • Low Distortion Negative Signal Capability The Intersil ISL54208 dual SPDT (Single Pole/Double Throw) switches combine low distortion audio/video and accurate USB 2.0 high speed (480Mbps) data signal switching in the same low voltage device. When operated with a 2.7V to 3.6V single supply these analog switches allow audio/video signal swings below-ground, allowing the use of a common USB and audio/video connector in digital cameras, camcorders and other portable battery powered Personal Media Player devices. • Control Pin to Open all Switches and Enter Low Power State • Low Distortion Mono Audio Signal - THD+N at 20mW into 32Ω Load . . . . . . . . . . . . . <0.1% • Low Distortion Color Video Signal - Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . 0.28% - Differential Phase. . . . . . . . . . . . . . . . . . . . . . . . . . 0.04° • Cross-talk NCx Channels (4MHz) . . . . . . . . . . . . . . -78dB The ISL54208 logic control pins are 1.8V logic compatible which allows control via a standard μcontroller. With a VDD voltage in the range of 2.7V to 3.6V the IN pin voltage can exceed the VDD rail allowing for the USB 5V VBUS voltage from a computer to directly drive the IN pin to switch between the audio/video and USB signal sources in the portable device. The part has an enable control pin to open all the switches and put the part in a low power state. • Single Supply Operation (VDD) . . . . . . . . . . . . 1.8V to 5.5V • -3dB Bandwidth USB NOx Switches . . . . . . . . . . . 630MHz • Available in μTQFN and TDFN Packages • Pb-Free Plus Anneal (RoHS Compliant) • Compliant with USB 2.0 Short Circuit Requirements Without Additional External Components The ISL54208 is available in a small 10 Ld 2.1mmx1.6mm ultra-thin μTQFN package and a 10 Ld 3mmx3mm TDFN package. It operates over a temperature range of -40 to +85°C. Applications • Digital Camera and Camcorders • Video MP3 and other Personal Media Players Related Literature • Cellular/Mobile Phones • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” • PDA’s • Audio/Video/USB Switching • Application Note AN557 “Recommended Test Procedures for Analog Switches” Application Block Diagram VDD USB AND AUDIO/VIDEO JACK IN VBUS μCONTROLLER ISL54208 CTRL LOGIC CIRCUITRY 4MΩ NO1 COM1 NO2 50kΩ COM2 50kΩ D- USB HIGH-SPEED D+ TRANSCEIVER NC1 NTSC or PAL NC2 VIDEO AUDIO GND 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54208 Pinouts (Note 1) ISL54208 (10 LD TDFN) TOP VIEW CTRL ISL54208 (10 LD μTQFN) TOP VIEW 10 4M VDD 1 4M 10 CTRL 9 NO1 9 NO1 IN 2 2 8 NO2 COM 1 3 8 NO2 COM 1 3 7 NC1 COM 2 4 7 NC1 COM 2 4 6 NC2 GND 5 6 NC2 VDD 1 IN LOGIC CONTROL LOGIC CONTROL 50k 50k 50k GND 5 50k NOTE: 1. ISL54208 Switches shown for IN = Logic “0” and CTRL = Logic “1”. Truth Table Pin Descriptions ISL54208 ISL54208 IN CTRL NC1, NC2 NO1, NO2 PIN NO. NAME 0 0 OFF OFF 1 VDD 0 1 ON OFF 2 IN 1 X OFF ON 3 COM1 Voice/Video and USB Common Pin 4 COM2 Voice/Video and USB Common Pin 5 GND Ground Connection 6 NC2 Audio or Video Input 7 NC1 Audio or Video Input 8 NO2 USB Differential Input 9 NO1 USB Differential Input 10 CTRL Digital Control Input (Audio/Vidio Enable) IN: Logic “0” when ≤ 0.5V, Logic “1” when ≥1.4V with 2.7V to 3.6V supply. CTRL: Logic “0” when ≤ 0.5V or Floating, Logic “1” when ≥1.4V with 2.7V to 3.6V supply. FUNCTION Power Supply Digital Control Input Ordering Information PART NUMBER (Note) PART MARKING TEMP. RANGE (°C) PACKAGE (Pb-Free) PKG. DWG. # ISL54208IRUZ-T FR -40 to +85 10 Ld 2.1x1.6mm μTQFN Tape and Reel L10.2.1x1.6A ISL54208IRZ-T 4208 -40 to +85 10 Ld 3mmx3mm TDFN Tape and Reel L10.3x3A ISL54208IRZ 4208 -40 to +85 10 Ld 3mmx3mm TDFN L10.3x3A NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate or NiPdAu termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN6410.0 December 18, 2006 ISL54208 Absolute Maximum Ratings Thermal Information VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6.0V Input Voltages NCx, NOx(Note 2) . . . . . . . . . . . . . . . . . . . . -2V to ((VDD) + 0.3V) IN (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2V to 5.5V CTRL (Note 2) . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((VDD) + 0.3V) Output Voltages COMx (Note 2) . . . . . . . . . . . . . . . . . . . . . . -2V to ((VDD) + 0.3V) Continuous Current (NCx, COMx) . . . . . . . . . . . . . . . . . . . ±150mA Peak Current (NCx, COMx) (Pulsed 1ms, 10% Duty Cycle, Max). . . . . . . . . . . . . . . . ±300mA Continuous Current (NOx) . . . . . . . . . . . . . . . . . . . . . . . . . . ±40mA Peak Current (NOx) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA ESD Rating: HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >7kV MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >400V CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1.4kV Thermal Resistance (Typical, Note 3) θJA (°C/W) 10 Ld μTQFN Package . . . . . . . . . . . . . . . . . . . . . . . 130 10 Ld 3x3 TDFN Package. . . . . . . . . . . . . . . . . . . . . 110 Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C Maximum Storage Temperature Range. . . . . . . . . . . . -65°C to +150°C Operating Conditions Temperature Range ISL54208IRUZ and ISL54208IRZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. Signals on NOx, NCx, COMx, CTRL, IN exceeding VDD or GND by specified amount are clamped. Limit current to maximum current ratings. 3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V, VCTRLH = 1.4V, VCTRLL = 0.5V, (Notes 4, 6), unless otherwise specified. PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS ANALOG SWITCH CHARACTERISTICS Audio/Video Switches (NC1, NC2) Analog Signal Range, VANALOG VDD = 3.0V, IN = 0.5V, CTRL = 1.4V Full -1.5 - 1.5 V ON Resistance, RON VDD = 3.0V, IN = 0.5V, CTRL = 1.4V, ICOMx = 100mA, VNCx = -0.85V to 0.85V, (See Figure 3) 25 - 2.65 4 Ω Full - - 5.5 Ω 25 - 0.02 0.13 Ω Full - - 0.16 Ω 25 - 0.03 0.05 Ω Full - - 0.07 Ω VDD = 3.6V, IN = 0V, CTRL = 3.6V, VCOM- or VCOM+ = -0.85V, 0.85V, VNCx = -0.85V, 0.85V, VNOx = floating, Measure current through the discharge pull-down resistor and calculate resistance value. 25 - 50 - kΩ Analog Signal Range, VANALOG VDD = 3.6V, IN = 1.4V, CTRL = 1.4V Full 0 - VDD V ON Resistance, RON VDD = 3.6V, IN = 1.4V, CTRL = 1.4V, ICOMx = 40mA, VNOx = 0V to 400mV (See Figure 4) 25 - 4.6 5 Ω Full - - 6.5 Ω 25 - 0.06 0.5 Ω Full - - 0.55 Ω 25 - 0.4 0.6 Ω Full - - 1.0 Ω RON Matching Between Channels, ΔRON VDD = 3.0V, IN = 0.5V, CTRL = 1.4V, ICOMx = 100mA, VNCx = Voltage at max RON over signal range of -0.85V to 0.85V, (Note 8) RON Flatness, RFLAT(ON) VDD = 3.0V, IN = 0.5V, CTRL = 1.4V, ICOMx = 100mA, VNCx = -0.85V to 0.85V, (Note 7) Discharge Pull-Down Resistance, RNC1, RNC2 USB Switches (NO1, NO2) RON Matching Between Channels, ΔRON VDD = 3.6V, IN = 1.4V, CTRL = 1.4V, ICOMx = 40mA, VNOx = Voltage at max RON, (Note 8) RON Flatness, RFLAT(ON) VDD = 3.6V, IN = 1.4V, CTRL = 1.4V, ICOMx = 40mA, VNOx = 0V to 400mV, (Note 7) 3 FN6410.0 December 18, 2006 ISL54208 Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V, VCTRLH = 1.4V, VCTRLL = 0.5V, (Notes 4, 6), unless otherwise specified. (Continued) PARAMETER TEST CONDITIONS OFF Leakage Current, INOx(OFF) VDD = 3.6V, IN = 0V, CTRL = 3.6V, VCOMx = 0.5V, 0V, VNOx = 0V, 0.5V, VNCx = float VDD = 3.3V, IN = 3.3V, CTRL = 0V or 3.3V, VNOx = 2.0V, VCOMx , VNCx = float ON Leakage Current, INOx TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS 25 -10 - 10 nA Full -70 - 70 nA 25 -10 2 10 nA Full -75 - 75 nA DYNAMIC CHARACTERISTICS Turn-ON Time, tON VDD = 2.7V, RL = 50Ω, CL = 10pF, (See Figure 1) 25 - 67 - ns Turn-OFF Time, tOFF VDD = 2.7V, RL = 50Ω, CL = 10pF, (See Figure 1) 25 - 48 - ns Break-Before-Make Time Delay, tD VDD = 2.7V, RL = 50Ω, CL = 10pF, (See Figure 2) 25 - 18 - ns Skew, tSKEW VDD = 3.3V, IN = 3.3V, CTRL = 3.3V, RL = 45Ω, CL = 10pF, tR = tF = 750ps at 480Mbps, (Duty Cycle = 50%) (See Figure 7) 25 - 50 - ps Total Jitter, tJ VDD = 3.3V, IN = 3.3V, CTRL = 3.3V, RL = 45Ω, CL = 10pF, tR = tF = 750ps at 480Mbps 25 - 210 - ps Propagation Delay, tPD VDD = 3.3V, IN = 3.3V, CTRL = 3.3V, RL = 45Ω, CL = 10pF, (See Figure 7) 25 - 250 - ps Crosstalk (Channel-to-Channel), NC2 to COM1, NC1 to COM2 VDD = 3.3V, IN = 0V, CTRL = 3.3V, RL = 75Ω, f = 4MHz, VNCx = 300mVP-P, (See Figure 6) 25 - -78 - dB Differential Gain VSIGNAL = 300mVp-p, VOFFSET = 0V to 0.7V, f = 3.58MHz, RL = 75 25 - 0.28 - % Differential Phase VSIGNAL = 300mVp-p, VOFFSET = 0V to 0.7V, f = 3.58MHz, RL = 75 25 - 0.04 - deg Total Harmonic Distortion f = 20Hz to 20kHz, VDD = 3.0V, IN = 0V, CTRL = 3.0V, VNCx = 0.707VRMS (2VP-P), RL = 32Ω 25 - 0.06 - % NCx (Audio/Video) Switch -3dB Bandwidth Signal = 8dBm, RL = 75Ω, CL = 5pF, (See Figure 14) 25 - 338 - MHz NOx (USB) Switch -3dB Bandwidth Signal = 0dBm, 0.2VDC offset, RL = 50Ω, CL = 5pF 25 - 630 - MHz NOx OFF Capacitance, CNOx(OFF) f = 1MHz, VDD = 3.0V, IN = 0V, CTRL = 3.0V, VNOx = VCOMx = 0V, (See Figure 5) 25 - 6 - pF NCx OFF Capacitance, CNCx(OFF) f = 1MHz, VDD = 3.0V, IN = 3.0V, CTRL = 3.0V, VNCx = VCOMx = 0V, (See Figure 5) 25 - 9 - pF COMx ON Capacitance, CCOMx(ON) f = 1MHz, VDD = 3.0V, IN = 3.0V, CTRL = 3.0V, VNOx = VCOMx = 0V, (See Figure 5) 25 - 10 - pF Full 1.8 5.5 V 25 - 6 8 μA Full - - 10 μA 25 - 1 7 nA Full - - 140 nA POWER SUPPLY CHARACTERISTICS Power Supply Range, VDD Positive Supply Current, IDD VDD = 3.6V, IN = 0V or 3.6V, CTRL = 3.6V Positive Supply Current, IDD (Low Power State) VDD = 3.6V, IN = 0V, CTRL = 0V or float DIGITAL INPUT CHARACTERISTICS Voltage Low, VINL, VCTRLL VDD = 2.7V to 3.6V Full - - 0.5 V Voltage High, VINH , VCTRLH VDD = 2.7V to 3.6V Full 1.4 - - V Input Current, IINL, ICTRLL VDD = 3.6V, IN = 0V, CTRL = 0V Full -50 20 50 nA Input Current, IINH VDD = 3.6V, IN = 3.6V, CTRL = 0V Full -50 20 50 nA 4 FN6410.0 December 18, 2006 ISL54208 Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V, VCTRLH = 1.4V, VCTRLL = 0.5V, (Notes 4, 6), unless otherwise specified. (Continued) PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS Input Current, ICTRLH VDD = 3.6V, IN = 0V, CTRL = 3.6V Full -2 1.1 2 μA CTRL Pull-Down Resistor, RCTRL VDD = 3.6V, IN = 0V, CTRL = 3.6V Full - 4 - MΩ NOTES: 4. VLOGIC = Input voltage to perform proper function. 5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 6. Parameters with limits are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation. 7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 8. RON matching between channels is calculated by subtracting the channel with the highest max RON value from the channel with lowest max RON value, between NC1 and NC2 or between NO1 and NO2. Test Circuits and Waveforms VDD LOGIC INPUT 50% C CTRL 0V VINPUT tOFF SWITCH INPUT VINPUT SWITCH INPUT VOUT NO or NC COMx IN VOUT 90% SWITCH OUTPUT VDD tr <20ns tf <20ns 90% VIN RL 50Ω GND CL 10pF 0V tON Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for all switches. CL includes fixture and stray capacitance. RL -----------------------------V OUT = V (INPUT) R + R L ( ON ) FIGURE 1A. MEASUREMENT POINTS FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES VDD VDD C CTRL LOGIC INPUT NOx VINPUT 0V VOUT COMx NCx VOUT 90% SWITCH OUTPUT VIN 0V RL 50Ω IN CL 10pF GND tD FIGURE 2A. MEASUREMENT POINTS Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 2B. TEST CIRCUIT FIGURE 2. BREAK-BEFORE-MAKE TIME 5 FN6410.0 December 18, 2006 ISL54208 Test Circuits and Waveforms (Continued) VDD VDD C RON = V1/100mA C RON = V1/40mA CTRL CTRL NCx NOx VNCx VNOx IN V1 OV 100mA VDD IN V1 40mA COMx COMx GND GND Repeat test for all switches. Repeat test for all switches. FIGURE 3. AUDIO/VIDEO RON TEST CIRCUIT FIGURE 4. USB RON TEST CIRCUIT VDD C VDD C CTRL SIGNAL GENERATOR CTRL NCx 75Ω COMx NCx or NOx IN 0V IN IMPEDANCE ANALYZER 0V or VDD COMx NCx COMx ANALYZER NC GND GND RL Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches. Repeat test for all switches. FIGURE 5. CAPACITANCE TEST CIRCUIT 6 FIGURE 6. NCx CROSSTALK TEST CIRCUIT FN6410.0 December 18, 2006 ISL54208 Test Circuits and Waveforms (Continued) VDD C tri CTRL 90% DIN+ 10% 50% VDD tskew_i DIN90% IN 15.8Ω DIN+ 50% COM1 143W 10% 15.8Ω DIN- tfi tro OUT+ NO1 CL COM2 OUT- NO2 CL 143Ω 45Ω 45Ω 90% 10% 50% OUT+ OUT- GND tskew_o 50% 90% |tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals. |tfo - tfi| Delay Due to Switch for Falling Input and Falling Output Signals. 10% tf0 |tskew_0| Change in Skew through the Switch for Output Signals. |tskew_i| Change in Skew through the Switch for Input Signals. FIGURE 7A. MEASUREMENT POINTS FIGURE 7B. TEST CIRCUIT FIGURE 7. SKEW TEST 7 FN6410.0 December 18, 2006 ISL54208 Application Block Diagrams VDD IN USB AND AUDIO/VIDEO JACK μCONTROLLER ISL54208 CTRL LOGIC CIRCUITRY VBUS 4MΩ NO1 COM1 D- USB HIGH-SPEED D+ TRANSCEIVER NO2 50kΩ COM2 NC1 NTSC or PAL NC2 VIDEO 50kΩ AUDIO GND LOGIC CONTROL VIA MICRO-PROCESSOR VDD USB AND AUDIO/VIDEO JACK VBUS IN μCONTROLLER ISL54208 CTRL LOGIC CIRCUITRY 22kΩ 4MΩ 4MΩ NO1 COM1 NO2 50kΩ COM2 D- USB HIGH-SPEED D+ TRANSCEIVER NC1 NTSC or PAL NC2 VIDEO 50kΩ AUDIO GND LOGIC CONTROL VIA VBUS VOLTAGE FROM COMPUTER OR USB HUB Detailed Description The ISL54208 device is a dual single pole/double throw (SPDT) analog switch device that can operate from a single dc power supply in the range of 1.8V to 5.5V. It was designed to function as a dual 2 to 1 multiplexer to select between USB differential data signals and mono audio/composite video baseband signals (CVBS). It comes in tiny μTQFN and TDFN packages for use in cameras, camcorders, video MP3 players, PDAs, cell phones, and other personal media players. The part consists of two 3Ω audio/video switches and two 5Ω USB switches. The audio/video switches can accept signals that swing below ground. They were designed to pass ground reference audio or dc restored with synch composite video signals with minimal distortion. The USB switches were designed to pass high-speed USB differential data signals with minimal edge and phase distortion. 8 The ISL54208 was specifically designed for digital cameras, camcorders, MP3 players, cell phones and other personal media player applications that need to combine the audio/video jacks and the USB data connector into a single shared connector, thereby saving space and component cost. Typical application block diagrams of this functionality is shown above. The ISL54208 logic control pins are 1.8V logic compatible and can be driven by a standard μcontroller. It has a single logic control pin (IN) that selects between the audio/video switches and the USB switches. The ISL54208 also contains a logic control pin (CTRL) that when driven Low while IN is Low, opens all switches and puts the part into a low power state, drawing typically 1nA of IDD current. A detailed description of the two types of switches is provided in the sections below. The USB transmission and FN6410.0 December 18, 2006 ISL54208 audio/video playback are intended to be mutually exclusive operations. NC1 and NC2 Audio/Video Switches The two NC (normally closed) audio/video switches (NC1, NC2) are 3Ω switches that can pass signals that swing below ground by as much as 1.5V. They were designed to pass ground reference audio signals and dc restored composite base-band signals (CVBS) including negative synchronizing pulse with minimal insertion loss and very low distortion and degradation. The -3dB bandwidth into 75Ω is 338MHz (Figure 17). Crosstalk between NC1 and NC2 @ 4MHz is -78dB (Figure 16) which allows composite video to be routed through one switch and mono-audio through the other switch with little interference. The recommended maximum signal range is from -1.5V to 1.5V. You can apply positive signals greater than 1.5V but the rON resistance of the switch increases rapidly above 1.5V. The signal should not be allowed to exceed the VDD rail or swing more negative than -1.5V. Over a signal range of ±1V (0.707Vrms) with VDD >2.7V, these switches have an extremely low rON resistance variation. They can pass a ground referenced audio signal with very low distortion (<0.06% THD+N) when delivering 15.6mW into a 32Ω headphone speaker load. See Figures 10, 11, 12, and 13 THD+N performance curves. Figures 8 and 9 shows the vector scope plots of a standard NTSC color bar signal at both the input (Figure 8) and output (Figure 9) of the ISL54208. The plots show that except for a little attentuation, due to switch RON and test fixture cabling, there is virtually no degradation of the video waveform through the switch. FIGURE 9. VECTOR-SCOPE PLOT AFTER SWITCH Figure 18 shows the differential gain (DG) and differential phase (DP) plots at the output of the switch using an actual NTSC composite video signal and a VM700A Video Measurement Test Set. DG = 0.28% and DP = 0.04deg. The NC switches are uni-directional switches. The audio/video sources should be connected at the NC side of the switch (pins 7 and 8) and the speaker load and video receiver should be connected at the COM side of the switch (pins 3 and 4). The NC switches are active (turned ON) whenever the IN voltage is ≤ to 0.5V and the CTRL voltage to ≥1.4V. Note: Whenever the NC switches are ON the USB transceiver drivers need to be in the high impedance state or static high or low state. NO1 and NO2 USB Switches The two NO (normally open) USB switches (NO1, NO2) are 5Ω bidirectional switches that were designed to pass highspeed USB differential signals in the range of ±0V to 400mV. These switches have low capacitance and high bandwidth to pass USB high-speed signals (480Mbps) with minimum edge and phase distortion to meet high-speed USB 2.0 highspeed signal quality specifications. See Figure 14 for Highspeed Eye Pattern taken with switch in the signal path. The maximum signal range for the USB switches is from -1.5V to VDD. The signal voltage at NO1 and NO2 should not be allow to exceed the VDD voltage rail or go below ground by more than -1.5V. The NO switches are active (turned ON) whenever the IN voltage is to ≥1.4V. FIGURE 8. VECTOR-SCOPE PLOT BEFORE SWITCH 9 Note: Whenever the NO switches are ON the audio and video drivers need to be at ac or dc ground or floating to keep from interfering with the data transmission. FN6410.0 December 18, 2006 ISL54208 ISL54208 Operation The discussion that follows will discuss using the ISL54208 in the typical application shown in the block diagrams on page 8. VDD SUPPLY The dc power supply connected at VDD (pin 1) provides the required bias voltage for proper switch operation. The part can operate with a supply voltage in the range of 1.8V to 5.5V. In a typical USB/Audio/Video application for portable battery powered devices the VDD voltage will come from a battery or an LDO and be in the range of 2.7V to 3.6V. For best possible USB full-speed operation (12Mbps) it is recommended that the VDD voltage be ≥3.3V in order to get a USB data signal level above 2.5V. LOGIC CONTROL The state of the ISL54208 device is determined by the voltage at the IN pin (pin 2) and the CTRL pin (pin 10). Refer to truth-table on page 2 of data sheet. These logic pins are 1.8V compatible with VDD in the range of 2.7V to 3.6V and can be controlled by a standard μprocessor. ISL54208 part will be in the audio/video mode and the media player audio and video drivers can drive the speaker and video display. USB Mode If the IN pin = Logic “1” and CTRL pin = Logic “0” or Logic “1” the part will go into USB mode. In USB mode, the NO1 and NO2 5Ω switches are ON and the NC1 and NC2 3Ω audio/video switches are OFF (high impedance). When a USB cable from a computer or USB hub is connected at the common connector, the μprocessor will sense the present of the 5V VBUS and drive the IN pin voltage high. The ISL54208 part will go into the USB mode. In USB mode, the computer or USB hub transceiver and the media player USB transceiver are connected and digital data will be able to be transmitted back and forth. When the USB cable is disconnected, the μprocessor will sense that the 5V VBUS voltage is no longer connected and will drive the IN pin low and put the part back into the Audio/Video or Low Power Mode. Low Power Mode The CTRL pin is internally pulled low through a 4MΩ resistors to ground and can be left floating or tri-stated by the μprocessor. The CTRL control pin is only active when IN is logic “0”. If the IN pin = Logic “0” and CTRL pin = Logic “0,” the part will be in the Low Power mode. In the Low Power mode, the NCx switches and the NOx switches are OFF (high impedance). In this state, the device draws typically 1nA of current. The IN pin does not have an internal pull-down resistor and must not be allowed to float. It must be driven High or Low. USING THE COMPUTER VBUS VOLTAGE TO DRIVE THE “IN” PIN The voltage at the IN pin can exceed the VDD voltage by as much as 2.55V. This allows the VBUS voltage from a computer or USB hub (4.4V to 5.25V) to drive the IN pin while the VDD voltage is in the range of 2.7V to 3.6V. An external pull-down resistor is required from the IN pin to ground when directly driving the IN pin with the computer VBUS voltage. See the section titled “USING THE COMPUTER VBUS VOLTAGE TO DRIVE THE “IN’ PIN”. External IN Pull-Down Resistor Logic control voltage levels: IN = Logic “0” (Low) when ≤0.5V IN = Logic “1” (High) when IN ≥1.4V CTRL = Logic “0” (Low) when ≤0.5V or floating. CTRL = Logic “1” (High) when ≥1.4V Audio/Video Mode If the IN pin = Logic “0” and CTRL pin = Logic “1,” the part will be in the Audio/Video mode. In Audio/Video mode the NC1 and NC2 3Ω audio/video switches are ON and the NO1 and NO2 5Ω USB switches are OFF (high impedance). When nothing is plugged into the common connector or a audio/video jack is plugged into the common connector, the μprocessor will sense that there is no voltage at the VBUS pin of the connector and will drive and hold the IN control pin of the ISL54208 low. As long as the CTRL = Logic “1,” the 10 Rather than using a micro-processor to control the IN logic pin you can directly drive the IN pin using the VBUS voltage from the computer or USB hub. In order to do this you must connected an external pull-down resistor from the IN pin to ground. When an audio/video jack or nothing is connected at the common connector the external pull-down resistor will pull the IN pin low putting the ISL54208 in the Audio/Video Mode or Low Power Mode depending on the condition of the CTRL pin. When a USB cable is connected at the common connector the voltage at the IN pin will be driven to 5V and the part will automatically go into the USB mode. When the USB cable is disconnected from the common connector the voltage at the IN pin will be pulled low by the pull-down resistor and return to the Audio/Video Mode or Low Power Mode depending on the condition of the CTRL pin. Note: The voltage at the IN pin can exceed the VDD voltage by as much as 2.55V. This allows the VBUS voltage from a computer or USB hub (4.4V to 5.25V) to drive the IN pin while the VDD voltage is in the range of 2.7V to 3.6V. FN6410.0 December 18, 2006 ISL54208 EXTERNAL SERIES RESISTOR AT IN LOGIC CONTROL PIN The ISL54208 contains a clamp circuit between IN and VDD. Whenever the IN voltage is greater than the VDD voltage by more than 2.55V, current will flow through this clamp circuitry into the VDD power supply bus. During normal USB operation, VDD is in the range of 2.7V to 3.6V and IN (VBUS voltage from computer or USB hub) is in the range of 4.4V to 5.25V, the clamp circuit is not active and no current will flow through the clamp into the VDD supply. In a USB application, the situation can exist where the VBUS voltage from the computer could be applied at the IN pin before the VDD voltage is up to its normal operating voltage range and current will flow through the clamp into the VDD power supply bus. This current could be quite high when VDD is OFF or at 0V and could potentially damage other components connected in the circuit. In the application circuit, a 22kΩ resistor has been put in series with the IN pin to limit the current to a safe level during this situation. It is recommended that a current limiting resistor in the range of 10kΩ to 50kΩ be connected in series with the IN pin. It will have minimal impact on the logic level at the IN pin during normal USB operation and protect the circuit during the time VBUS is present before VDD is up to its normal operating voltage. Note: No external resistor is required in applications where IN pin voltage will not exceed VDD by more than 2.55V. Typical Performance Curves TA = +25°C, Unless Otherwise Specified 0.11 0.4 RLOAD = 32Ω VDD = 3V RLOAD = 32Ω VLOAD = 0.707VRMS 0.1 3VP-P 0.3 0.09 THD+N (%) THD+N (%) VDD = 2.6V 0.08 0.07 VDD = 2.7V 0.06 0.05 2VP-P 1VP-P 0 0.04 20 200 2K FREQUENCY (Hz) 20K 20 FIGURE 10. THD+N vs SUPPLY VOLTAGE vs FREQUENCY 200 2K FREQUENCY (Hz) 20K FIGURE 11. THD+N vs SIGNAL LEVELS vs FREQUENCY 0.5 0.5 RLOAD = 32Ω FREQ = 1kHz VDD = 3V 0.4 RLOAD = 32Ω FREQ = 1kHz VDD = 3V 0.4 0.3 THD+N (%) THD+N (%) 2.5VP-P 0.1 VDD = 3.6V VDD = 3V 0.2 0.2 0.3 0.2 0.1 0.1 0 0 0 0.5 1 1.5 2 2.5 3 OUTPUT VOLTAGE (VP-P) FIGURE 12. THD+N vs OUTPUT VOLTAGE 11 3.5 0 10 20 30 40 50 OUTPUT POWER (mW) FIGURE 13. THD+N vs OUTPUT POWER FN6410.0 December 18, 2006 ISL54208 VOLTAGE (835mV/DIV) Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) TIME (10ns/DIV) FIGURE 14. EYE PATTERN: 480Mbps WITH NOx SWITCHES IN THE SIGNAL PATH 1 0 0 -10 -1 -20 -2 -30 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) NOx Switch -3 -4 -40 -50 -60 -70 -80 -90 RL = 50Ω VIN = 0.2VP-P to 2VP-P 1M RL = 75Ω VIN = 0.2VP-P to 2VP-P 10M 100M FREQUENCY (Hz) FIGURE 15. FREQUENCY RESPONSE 12 1G -110 0.001 0.01 3 6 10 0.1 1 FREQUENCY (MHz) 100 500 FIGURE 16. VIDEO TO AUDIO CROSSTALK FN6410.0 December 18, 2006 ISL54208 GAIN (%) 1 NCx Switches 0 -1 -2 PHASE (DEG) NORMALIZED GAIN (dB) Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) -3 -4 RL = 75Ω VIN = 0.2VP-P to 2VP-P 1M 10M 100M FREQUENCY (Hz) FIGURE 17. 1G FIGURE 18. Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND (TDFN Paddle Connection: Tie to GND or Float) TRANSISTOR COUNT: 98 PROCESS: Submicron CMOS 13 FN6410.0 December 18, 2006 ISL54208 Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN) D 6 INDEX AREA A L10.2.1x1.6A B N 10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS E SYMBOL 2X MIN NOMINAL MAX 1 2X 2 0.10 C TOP VIEW C A 0.05 C SEATING PLANE 1 0.45 0.50 0.55 - - - 0.05 - 0.127 REF - b 0.15 0.20 0.25 5 D 2.05 2.10 2.15 - E 1.55 1.60 1.65 - A1 e SIDE VIEW k 0.20 - - - L 0.35 0.40 0.45 - (DATUM A) PIN #1 ID A A1 A3 0.10 C 4xk 2 NX L 0.50 BSC - N 10 2 Nd 4 3 Ne 1 3 θ N 0 - 12 (DATUM B) N-1 NX b e NOTES: 5 BOTTOM VIEW CL (A1) L 5 e SECTION "C-C" TERMINAL TIP C C 4 Rev. 3 6/06 0.10 M C A B 0.05 M C 3 (ND-1) X e NX (b) NOTES 0.10 C FOR ODD TERMINAL/SIDE b 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on D and E side, respectively. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Maximum package warpage is 0.05mm. 8. Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. 2.50 1.75 0.05 MIN L 2.00 0.80 0.275 0.10 MIN 0.25 DETAIL “A” PIN 1 ID 0.50 LAND PATTERN 10 14 FN6410.0 December 18, 2006 ISL54208 Thin Dual Flat No-Lead Plastic Package (TDFN) L10.3x3A 2X 0.10 C A A 10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE D MILLIMETERS 2X 0.10 C B SYMBOL MIN NOMINAL MAX NOTES A 0.70 0.75 0.80 - A1 - - 0.05 - E A3 6 INDEX AREA TOP VIEW B // A C SEATING PLANE 0.08 C b 0.20 0.25 0.30 5, 8 D 2.95 3.0 3.05 - D2 2.25 2.30 2.35 7, 8 E 2.95 3.0 3.05 - E2 1.45 1.50 1.55 7, 8 e 0.50 BSC - k 0.25 - - - L 0.25 0.30 0.35 8 A3 SIDE VIEW D2 (DATUM B) 0.10 C 0.20 REF 7 8 N 10 2 Nd 5 3 Rev. 3 3/06 D2/2 NOTES: 6 INDEX AREA 1 2 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. NX k 3. Nd refers to the number of terminals on D. (DATUM A) 4. All dimensions are in millimeters. Angles are in degrees. E2 E2/2 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX L N N-1 NX b 8 e (Nd-1)Xe REF. BOTTOM VIEW 5 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 0.10 M C A B 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Compliant to JEDEC MO-229-WEED-3 except for D2 dimensions. CL NX (b) (A1) L1 5 9 L e SECTION "C-C" C C TERMINAL TIP FOR ODD TERMINAL/SIDE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 FN6410.0 December 18, 2006