ISL54223 ® Data Sheet February 9, 2009 High-Speed USB 2.0 (480Mbps) Multiplexer FN6836.0 Features • High-Speed (480Mbps) and Full-Speed (12Mbps) Signaling Capability per USB 2.0 The Intersil ISL54223 is a single supply dual 2:1 multiplexer that can operate from a single 1.8V to 3.3V supply. It contains two SPDT (Single Pole/Double Throw) switches configured as a DPDT. The part was designed for switching or routing of USB High-Speed signals and/or USB Full-speed signals in portable battery powered products. • 1.8V Logic Compatible • Enable Pin to Open all Switches • Power OFF Protection • D-/D+ Pins Overvoltage Tolerant to 5.5V The 5.5Ω switches can swing rail-to-rail and were specifically designed to pass USB full speed data signals that range from 0V to 3.3V and USB high speed data signals that range from 0V to 400mV with a single supply as low as 1.8V. They have high bandwidth and low capacitance to pass USB high speed data signals with minimal distortion. • -3dB Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 782MHz • Low ON Capacitance. . . . . . . . . . . . . . . . . . . . . . . . 6.5pF • Low ON-Resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 5.5Ω • Single Supply Operation (VDD) . . . . . . . . . . . . 1.8V to 3.3V • Available in µTQFN Package The part can be used in Personal Media Players and other portable battery powered devices that need to route USB high-speed signals and/or full-speed signals to different transceiver sections of the device while connected to a single USB host (computer). • Pb-Free (RoHS Compliant) • Compliant with USB 2.0 Short Circuit and Overvoltage Requirements Without Additional External Components Applications The digital logic inputs are 1.8V logic compatible when operated with a 1.8V to 3.3V supply. The ISL54223 has an output enable pin to open all the switches. It can be used to facilitate proper bus disconnect and connection when switching between the USB sources. • MP3 and other Personal Media Players • Cellular/Mobile Phones • PDA’s The ISL54223 is available in a 10 Ld 2.1mmx1.6mm µTQFN package. It operates over a temperature range of -40 to +85°C. • Digital Cameras and Camcorders • USB Switching Application Block Diagram µCONTROLLER VDD ISL54223 SEL USB CONNECTOR VBUS OE LOGIC CIRCUITRY HSD1- D- D- HSD1+ D+ D+ HSD2HSD2+ GND GND USB HIGH-SPEED OR FULL-SPEED TRANSCEIVER #1 USB HIGH_SPEED OR FULL-SPEED TRANSCEIVER #2 PORTABLE MEDIA DEVICE 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54223 Pinouts VDD ISL54223 (10 LD 2.1 X 1.6 µTQFN) TOP VIEW 10 LOGIC CONTROL 9 OE 2 8 HSD1- HSD2+ 3 7 HSD2- D+ 4 6 D- SEL 1 HSD1+ GND 5 NOTE: 1. Switches Shown for SEL = Logic “1” and OE = Logic “0”. Truth Table Pin Descriptions OE SEL HSD1-, HSD1+ HSD2-, HSD2+ PIN NAME 0 0 ON OFF VDD Power Supply 0 1 OFF ON GND Ground Connection 1 X OFF OFF SEL Select Logic Control Input OE Bus Switch Enable Logic “0” when ≤ 0.5V, Logic “1” when ≥ 1.4V with a 1.8V to 3.3V Supply. DESCRIPTION D+, D-, HSDx+, HSDx- USB Data Port Ordering Information PART NUMBER (Note) ISL54223IRUZ-T* PART MARKING GN TEMP. RANGE (°C) -40 to +85 PACKAGE (Pb-Free) 10 Ld 2.1x1.6mm µTQFN Tape and Reel PKG. DWG. # L10.2.1x1.6A *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN6836.0 February 9, 2009 ISL54223 Absolute Maximum Ratings Thermal Information VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 3.5V Input Voltages HSD2x, HSD1x (Note 2). . . . . . . . . . . . . . . . . . . . . - 0.3V to 6.0V SEL, OE (Note 2) . . . . . . . . . . . . . . . . . . . -0.3V to ((VDD) + 0.3V) Output Voltages D+, D- (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V Continuous Current (HSD2x, HSD1x) . . . . . . . . . . . . . . . . . . ±40mA Peak Current (HSD2x, HSD1x) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA ESD Rating: Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>2kV Thermal Resistance (Typical, Note 3) θJA (°C/W) 10 Ld µTQFN Package . . . . . . . . . . . . . . . . . . . . . . 155 Maximum Junction Temperature (Plastic Package). . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C VDD Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . 1.8V to 3.3V Logic Control Input Voltage . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 2. Signals on HSD1x, HSD2x, D+, D- exceeding GND by specified amount are clamped. Signals on OE and SEL exceeding VDD or GND by specified amount are clamped. Limit current to maximum current ratings. 3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 1.8V to 3.3V Supply Test Conditions: VDD = +3.3V, GND = 0V, VSELH = 1.4V, VSELL = 0.5V, VOEH = 1.4V, VOEL = 0.5V, (Note 4), Unless Otherwise Specified. PARAMETER TEST CONDITIONS TEMP MIN (°C) (Notes 5, 6) TYP MAX (Notes 5, 6) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG VDD = VDD, SEL = 0V or VDD, OE = 0V ON-Resistance, rON (High-Speed) VDD = 1.8V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, VHSD1x or VHSD2 x = 0V to 400mV (see Figure 3, Note 9) rON Matching Between Channels, VDD = 1.8V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, ΔrON (High-Speed) VHSD1x or VHSD2 x = Voltage at max rON, (Notes 8, 9) rON Flatness, RFLAT(ON) (High-Speed) VDD = 1.8V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, VHSD1x or VHSD2 x = 0V to 400mV (Notes 7, 9) OFF Leakage Current, IHSD1x(OFF) VDD = 3.3V, SEL = VDD and OE = 0V or OE = VDD, VDx = 0.3V, 3V, VHSD1X = 3V, 0.3V, VHSD2x = 0.3V, 3V ON Leakage Current, IHSD1x(ON) VDD = 3.3V, SEL = OE = 0V, VDx = 0.3V, 3V, VHSD1X = 0.3V, 3V, VHSD2x = 3V, 0.3V OFF Leakage Current, IHSD2x(OFF) VDD = 3.3V, SEL = OE = 0V or OE = VDD, VDx = 3V, 0.3V, VHSD2x = 0.3V, 3V, VHSD1X = 3V, 0.3V ON Leakage Current, IHSD2x(ON) VDD = 3.3V, SEL = VDD, OE = 0V, VDx = 0.3V, 3V, VHSD2x = 0.3V, 3V, VHSD1X = 3V, 0.3V Power OFF Leakage Current, IOFF VDD = 0V, VD+ = 0V to 5.25V, VD- = 0V to 5.25V Full 0 - VDD V 25 - 5.5 8 Ω Full - - 10 Ω 25 - 0.072 0.5 Ω Full - - 0.55 Ω 25 - 0.44 1.2 Ω Full - - 1.3 Ω 25 -15 0.35 15 nA Full -20 - 20 nA 25 -20 2.5 20 nA Full -25 - 25 nA 25 -15 0.26 15 nA Full -20 - 20 nA 25 -20 1.65 20 nA Full -25 - 25 nA 25 - 0.005 0.025 µA Full - - 0.5 µA DYNAMIC CHARACTERISTICS Turn-ON Time, tON VDD = 3.3V, RL = 50Ω, CL = 50pF (see Figure 1) 25 - 50 - ns Turn-OFF Time, tOFF VDD = 3.3V, RL = 50Ω, CL = 50pF (see Figure 1) 25 - 33 - ns Break-Before-Make Time Delay, tD VDD = 3.3V, RL = 50Ω, CL = 50pF (see Figure 2) 25 - 12 - ns Turn-ON Enable Time, tENABLE 25 - 42 - ns VDD = 3.3V, RL = 15kΩ, CL = 50pF, Time-out of All-Off state 3 FN6836.0 February 9, 2009 ISL54223 Electrical Specifications - 1.8V to 3.3V Supply Test Conditions: VDD = +3.3V, GND = 0V, VSELH = 1.4V, VSELL = 0.5V, VOEH = 1.4V, VOEL = 0.5V, (Note 4), Unless Otherwise Specified. (Continued) PARAMETER TEST CONDITIONS TEMP MIN (°C) (Notes 5, 6) TYP MAX (Notes 5, 6) UNITS Turn-OFF Disable Time, tDISABLE VDD = 3.3V, RL = 15kΩ, CL = 50pF, Time into All-Off state, Time is highly dependent on the load (RL, CL) time constant. 25 - 75 - ns Skew, (tSKEWOUT - tSKEWIN) VDD = 3.3V, SEL = 0V or 3.3V, OE = 0V, RL = 45Ω, CL = 10pF, tR = tF = 500ps at 480Mbps, (Duty Cycle = 50%) (see Figure 6) 25 - 53 - ps Rise/Fall Degradation (Propagation Delay), tPD VDD = 3.3V, SEL = 0V or 3.3V, OE = 0V, RL = 45Ω, CL = 10pF (see Figure 6) 25 - 250 - ps Crosstalk VDD = 3.3V, RL = 50Ω, f = 240MHz (see Figure 5) 25 - -25 - dB OFF-Isolation VDD = 3.3V, OE = 3.3V, RL = 50Ω, f = 240MHz 25 - -27 - dB -3dB Bandwidth Signal = 0dBm, 0.2VDC offset, RL = 50Ω 25 - 782 - MHz OFF Capacitance, CHSxOFF f = 1MHz, VDD = 3.3V, SEL = 0V, OE = 3.3V, VHSD1x or VHSD2x = VDx = 0V (see Figure 4) 25 - 2.5 - pF COM ON Capacitance, CDX(ON) f = 1MHz, VDD = 3.3V, SEL = 0V or 3.3V, OE = 0V, VHSD1x or VHSD2x = VDx = 0V (see Figure 4) 25 - 6.5 - pF Full 1.8 3.3 V 25 - 32 40 µA Full - - 50 µA 25 - 5.8 7.5 µA Full - - 8 µA VDD = 1.8V to 3.3V Full - - 0.5 V Input Voltage High, VSELH, VOEH VDD = 1.8V to 3.3V Full 1.4 - VDD V Input Current, ISELL, IOEL VDD = 3.3V, SEL = 0V, OE = 0V Full - 104 - nA Input Current, ISELH VDD = 3.3V, SEL = 3.3V Full - -1.5 - nA Input Current, IOEH VDD = 3.3V, OE = 3.3V Full - -1.6 - nA POWER SUPPLY CHARACTERISTICS Power Supply Range, VDD Positive Supply Current, IDD Positive Supply Current, IDD VDD = 3.3V, SEL = 0V or VDD, OE = 0V or VDD VDD = 1.8V, SEL = 0V, OE = 0V or VDD DIGITAL INPUT CHARACTERISTICS Input Voltage Low, VSELL, VOEL NOTES: 4. VLOGIC = Input voltage to perform proper function. 5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 6. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 7. Flatness is defined as the difference between maximum and minimum value of ON-resistance over the specified analog signal range. 8. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON value, between HSD2+ and HSD2- or between HSD1+ and HSD1-. 9. Limits established by characterization and are not production tested. 4 FN6836.0 February 9, 2009 ISL54223 Test Circuits and Waveforms VDD LOGIC INPUT VDD tr < 20ns tf < 20ns 50% 0V VINPUT tOFF SWITCH INPUT VINPUT SWITCH INPUT VOUT HSDxx Dx SEL VOUT 90% 90% SWITCH OUTPUT C VIN CL RL OE GND 0V tON Repeat test for all switches. CL includes fixture and stray capacitance. RL V OUT = V (INPUT) -----------------------R L + r ON Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. MEASUREMENT POINTS FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES VDD C VDD LOGIC INPUT HSD2x VINPUT 0V VOUT Dx HSD1x CL RL SEL SWITCH OUTPUT VOUT 90% GND VIN 0V OE tD Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 2B. TEST CIRCUIT FIGURE 2A. MEASUREMENT POINTS FIGURE 2. BREAK-BEFORE-MAKE TIME VDD C rON = V1/40mA HSDx VHSDX SEL V1 40mA 0V OR VDD Dx GND OE Repeat test for all switches. FIGURE 3. rON TEST CIRCUIT 5 FN6836.0 February 9, 2009 ISL54223 Test Circuits and Waveforms (Continued) VDD VDD C C HSDxx SIGNAL GENERATOR HSD1x 50Ω Dx SEL SEL IMPEDANCE ANALYZER 0V OR VDD Dx GND VIN OE HSD2x Dx ANALYZER GND RL NC OE Repeat test for all switches. Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches. FIGURE 5. CROSSTALK TEST CIRCUIT FIGURE 4. CAPACITANCE TEST CIRCUIT VDD C tri 90% DIN+ 10% VIN 50% tskew_i DIN- 90% SEL 15.8Ω DIN+ 50% 143Ω 10% DIN- tfi tro 15.8Ω OUT+ D2 COMD2 CL COMD1 OUT- D1 OE 143Ω 45Ω CL 45Ω 90% OUT+ OUT- 10% 50% GND tskew_o 50% 90% 10% tf0 |tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals. |tfo - tfi| Delay Due to Switch for Falling Input and Falling Output Signals |tskew_0| Change in Skew through the Switch for Output Signals. |tskew_i| Change in Skew through the Switch for Input Signals. FIGURE 6B. TEST CIRCUIT FIGURE 6A. MEASUREMENT POINTS FIGURE 6. SKEW TEST 6 FN6836.0 February 9, 2009 ISL54223 Application Block Diagram µCONTROLLER VDD ISL54223 SEL USB CONNECTOR OE LOGIC CIRCUITRY VBUS HSD1- D- D- HSD1+ D+ D+ HSD2HSD2+ GND GND USB HIGH-SPEED OR FULL-SPEED TRANSCEIVER #1 USB HIGH_SPEED OR FULL-SPEED TRANSCEIVER #2 PORTABLE MEDIA DEVICE Detailed Description The ISL54223 device is a dual single pole/double throw (SPDT) analog switch configured as a DPDT that operates from a single DC power supply in the range of 1.8V to 3.3V. It was designed to function as a dual 2-to-1 multiplexer to select between two USB high-speed differential data signals in portable battery powered products. It is offered in a small µTQFN package for use in MP3 players, cameras, PDAs, cell phones, and other personal media players. The device has an enable pin to open all switches. The part consists of four 5.5Ω high speed (HSx) switches. These switches have high bandwidth and low capacitance to pass USB high-speed (480Mbps) differential data signals with minimal edge and phase distortion. They can also swing from 0V to VDD to pass USB full speed (12Mbps) differential data signals with minimal distortion. The ISL54223 was designed for MP3 players, cameras, cell phones, and other personal media player applications that have multiple high-speed and/or full-speed transceivers sections and need to multiplex between these USB sources to a single USB host (computer). A typical application block diagram of this functionality is previously shown. A detailed description of the HS switches is provided in the following section. High-Speed (HSx) Switches The HSx switches (HSD1-, HSD1+, HSD2-, HSD2+) are bi-directional switches that can pass rail-to-rail signals. When powered with a 1.8V supply, these switches have a nominal rON of 5.5Ω over the signal range of 0V to 400mV with a rON flatness of 0.44Ω. The rON matching between the HSD1 and HSD2 switches over this signal range is only 0.072Ω, ensuring minimal impact by the switches to USB high speed signal transitions. As the signal level increases, 7 the rON switch resistance increases. At signal level of 1.8V, the switch resistance is nominally 12Ω. See Figures 7, 8, 9, 10, 11 and 12 in the “Typical Performance Curves” beginning on page 9. The HSx switches were specifically designed to pass USB 2.0 high-speed (480Mbps) differential signals in the range of 0V to 400mV. They have low capacitance (6.5pF) and high bandwidth to pass the USB high-speed signals with minimum edge and phase distortion to meet USB 2.0 high speed signal quality specifications. See Figure 13 in the “Typical Performance Curves” on page 9 for USB High-speed Eye Pattern taken with switches in the differential signal paths. The HSx switches can also pass USB full-speed signals (12Mbps) with minimal distortion and meet all the USB requirements for USB 2.0 full-speed signaling. See Figures 14 and 15 in the “Typical Performance Curves” on page 11 for USB Full-speed Eye Patterns taken with switches in the differential signal paths. The maximum normal operating signal range for the HSx switches is from 0V to VDD. The signal voltage should not be allow to exceed the VDD voltage rail or go below ground by more than -0.3V for normal operation. However, in the event that the USB 5.25V VBUS voltage gets shorted to one or both of the D-/D+ pins, the ISL54223 has special fault protection circuitry to prevent damage to the ISL54223 part. The fault circuitry allows the signal pins (D-, D+, HSD1-, HSD1+, HSD2-, HSD2+) to be driven up to 5.5V while the VDD supply voltage is in the range of 0V to 3.3V. In this condition the part draws < 300µA of IDD current and causes no stress to the IC. In addition when VDD is at 0V (ground) all switches are OFF and the fault voltage is isolated from the other side of the switch. When VDD is in the range of 1.8V to 3.3V the fault voltage will pass through to FN6836.0 February 9, 2009 ISL54223 the output of an active switch channel. During the fault condition normal operation is not guaranteed until the fault is removed. See the “USB 2.0 VBUS Short Requirements” section below. established between the USB 1 transceiver section of the media player and the computer. The device will be able to transmit and receive data from the computer. The HS1 channel switches are active (turned ON) whenever the SEL voltage is logic”0” (Low) and the OE voltage is logic”0”(Low). If the SEL pin = Logic “1” and the OE pin = Logic “0”, high-speed Channel 2 will be ON. The HSD2- and HSD2+ switches are ON and the HSD1- and HSD1+ switches are OFF (high impedance). The HS2 channel switches are active (turned ON) whenever the SEL voltage is logic “1” (High) and the OE voltage is logic “0” (Low). ISL54223 Operation The following will discuss using the ISL54223 shown in the “Application Block Diagram” on page 7. POWER HSD2 USB Channel When a USB cable from a computer or USB hub is connected at the common USB connector and Channel 2 is active, a link will be established between the USB 2 transceiver section of the media player and the computer. The device will be able to transmit and receive data from the computer. All Switches OFF Mode The power supply connected at the VDD pin provides the DC bias voltage required by the ISL54223 part for proper operation. The ISL54223 can be operated with a VDD voltage in the range of 1.8V to 3.3V. A 0.01µF or 0.1µF decoupling capacitor should be connected from the VDD pin to ground to filter out any power supply noise from entering the part. The capacitor should be located as close to the VDD pin as possible. LOGIC CONTROL The state of the ISL54223 device is determined by the voltage at the SEL pin and the OE pin. SEL is only active when the OE pin is logic “0” (Low). Refer to the “Truth Table” on page 2. The ISL54223 logic pins are designed to minimize current consumption when the logic control voltage is lower than the VDD supply voltage. With VDD = 3.3V and logic pins at 1.4V the part typically draws only 35µA of IDD current. With VDD = 1.8V and logic pins at 1.4V the part typically draws only 6µA IDD current. Driving the logic pins to the VDD supply rail minimizes power consumption. The logic pins must be held High or Low and must not float. Logic Control Voltage Levels With VDD supply voltage in the range of 1.8V to 3.3V the logic levels are: OE = Logic “0” (Low) when VOE ≤ 0.5V OE = Logic “1” (High) when VOE ≥ 1.4V SEL = Logic “0” (Low) when VSEL ≤ 0.5V SEL = Logic “1” (High) when VSEL ≥ 1.4V HSD1 USB Channel If the SEL pin = Logic “0” and the OE pin = Logic “0”, high-speed Channel 1 will be ON. The HSD1- and HSD1+ switches are ON and the HSD2- and HSD2+ switches are OFF (high impedance). If the SEL pin = Logic “0” or Logic “1” and the OE pin = Logic “1”, all of the switches will turn OFF (high impedance). The “ALL OFF” state can be used to switch between the two USB sections of the media player. When switching from one USB transceiver section to the other USB transceiver section, you can momentarily put the ISL54222 switch in the “All OFF” state, in order to get the computer to disconnect from the current USB section, so it can properly connect to the other USB transceiver section when that channel is turned ON. USB 2.0 VBUS Short Requirements The USB 2.0 specification in chapter 7, section 7.1.1 states a USB device must be able to withstand a VBUS short to the D+ or D- signal lines when the device is either powered off or powered on for at least 24 hours. The ISL54223 part has special fault protection circuitry to meet these short circuit requirements. The fault protection circuitry allows the signal pins (D-, D+, HSD1-, HSD1+, HSD2-, HSD2+) to be driven up to 5.5V while the VDD supply voltage is in the range of 0V to 3.3V. In this overvoltage condition the part draws < 300µA of IDD current and causes no stress/damage to the IC. In addition when VDD is at 0V (ground), all switches are OFF and the shorted VBUS voltage is isolated from the other side of the switch. When VDD is in the range of 1.8V to 3.3V, the shorted VBUS voltage will pass through to the output of an active (turned ON) switch channel but not through a turned OFF channel. Any components connected on the active channel must be able to withstand the overvoltage condition. Note: During the fault condition normal operation of the USB channel is not guaranteed until the fault condition is removed. When a computer or USB hub is plugged into the common USB connector and Channel 1 is active, a link will be 8 FN6836.0 February 9, 2009 ISL54223 Typical Performance Curves TA = +25°C, Unless Otherwise Specified 14 6.0 ICOM = 40mA ICOM = 1mA 1.8V 12 5.5 1.8V 10 rON (Ω) rON (Ω) 5.0 2.7V 4.5 3.3V 4.0 8 3.0V 2.7V 6 3.3V 3.0V 3.5 3.0 4 2 0 0.1 0.2 VCOM (V) 0.3 0.4 0.5 1.0 1.5 2.0 VCOM (V) 3.0 3.3 16 8 V+ = 1.8V ICOM = 40mA V+ = 1.8V ICOM = 1mA 14 7 12 +85°C 6 +25°C 4 -40°C rON (Ω) 10 5 +85°C 8 +25°C 6 -40°C 4 3 2 2.5 FIGURE 8. ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE FIGURE 7. ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE rON (Ω) 0 2 0 0.1 0.2 0.3 0 0 0.4 0.2 0.4 0.6 VCOM (V) FIGURE 9. ON-RESISTANCE vs SWITCH VOLTAGE 5.5 9 1.4 1.6 1.8 V+ = 3.3V ICOM = 1mA 8 7 +85°C 4.5 1.2 FIGURE 10. ON-RESISTANCE vs SWITCH VOLTAGE V+ = 3.3V ICOM = 40mA 5.0 0.8 1.0 VCOM (V) +85°C 4.0 rON (W) rON (Ω) 6 +25°C 3.5 +25°C 5 4 -40°C 3 -40°C 3.0 2 2.5 1 2.0 0 0 0.1 0.2 0.3 VCOM (V) FIGURE 11. ON-RESISTANCE vs SWITCH VOLTAGE 9 0.4 0 0.5 1.0 1.5 2.0 2.5 3.0 3.3 VCOM (V) FIGURE 12. ON-RESISTANCE vs SWITCH VOLTAGE FN6836.0 February 9, 2009 ISL54223 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VOLTAGE SCALE (0.1V/DIV) VDD = 1.8V TIME SCALE (0.2ns/DIV) FIGURE 13. EYE PATTERN: 480Mbps WITH USB SWITCHES IN THE SIGNAL PATH 10 FN6836.0 February 9, 2009 ISL54223 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VOLTAGE SCALE (0.5V/DIV) VDD = 1.8V TIME SCALE (10ns/DIV) FIGURE 14. EYE PATTERN: 12Mbps WITH USB SWITCHES IN THE SIGNAL PATH VOLTAGE SCALE (0.5V/DIV) VDD = 3.3V TIME SCALE (10ns/DIV) FIGURE 15. EYE PATTERN: 12Mbps WITH USB SWITCHES IN THE SIGNAL PATH 11 FN6836.0 February 9, 2009 ISL54223 1 -10 0 -20 -1 -30 -2 -40 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) -3 -4 RL = 50Ω VIN = 0dBm, 0.2VDC BIAS RL = 50W VIN = 0dBm, 0.2VDC BIAS -50 -60 -70 -80 -90 -100 1M 10M 100M 1G -110 1k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 16. FREQUENCY RESPONSE FIGURE 17. OFF-ISOLATION -10 -20 Die Characteristics RL = 50Ω VIN = 0dBm, 0.2VDC BIAS SUBSTRATE POTENTIAL (POWERED UP): -30 NORMALIZED GAIN (dB) 100M 500M GND -40 TRANSISTOR COUNT: -50 325 -60 PROCESS: -70 Submicron CMOS -80 -90 -100 -110 1k 10k 100k 1M 10M FREQUENCY (MHz) 100M 500M FIGURE 18. CROSSTALK All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 FN6836.0 February 9, 2009 ISL54223 Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN) D 6 INDEX AREA A L10.2.1x1.6A B N 10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS E SYMBOL 2X MIN NOMINAL MAX 1 2X 2 0.10 C TOP VIEW C A 0.05 C SEATING PLANE 1 0.45 0.50 0.55 - A1 - - 0.05 - 0.127 REF - b 0.15 0.20 0.25 5 D 2.05 2.10 2.15 - E 1.55 1.60 1.65 - A1 e SIDE VIEW k 0.20 - - L 0.35 0.40 0.45 (DATUM A) PIN #1 ID A A3 0.10 C 4xk 2 NX L 0.50 BSC - NX b e 2 Nd 4 3 Ne 1 3 0 12 - NOTES: 5 BOTTOM VIEW CL (A1) L 5 e SECTION "C-C" TERMINAL TIP C C 4 Rev. 3 6/06 0.10 M C A B 0.05 M C 3 (ND-1) X e - 10 (DATUM B) N-1 - N θ N NX (b) NOTES 0.10 C FOR ODD TERMINAL/SIDE b 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on D and E side, respectively. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Maximum package warpage is 0.05mm. 8. Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. 2.50 1.75 0.05 MIN L 2.00 0.80 0.275 0.10 MIN DETAIL “A” PIN 1 ID 0.50 0.25 LAND PATTERN 10 13 FN6836.0 February 9, 2009