ISL54217 ® Data Sheet May 4, 2009 USB 2.0 High-Speed x 2Channels/Stereo Audio Dual SP3T (Dual 3-to-1 Multiplexer) FN6817.3 Features • High Speed (480Mbps) and Full Speed (12Mbps) Signaling Capability per USB 2.0 The Intersil ISL54217 is a single supply dual SP3T analog switch that operates from a single supply in the range of 2.7V to 4.6V. It was designed to multiplex between audio stereo signals and two different USB 2.0 high speed differential data signals. The audio channels allow signal swings below ground, allowing the multiplexing of voice and data signals through a common headphone connector in Personal Media Players and other portable battery powered devices. • Low Distortion Negative Signal Capability Audio Switches • Clickless/Popless Audio Switches • Power OFF Protection • COM Pins Overvoltage Tolerant to 5.5V • Low Distortion Headphone Audio Signals - THD+N at 5mW into 32Ω Load . . . . . . . . . . . . . <0.03% The audio switch cells can pass ±1V ground referenced audio signals with very low distortion (<0.03% THD+N when driving 5mW into 32Ω loads). The USB switch cells have very low ON-capacitance (8pF) and high bandwidth to pass USB high speed signals (480Mbps) with minimal edge and phase distortion. • Crosstalk (100kHz) . . . . . . . . . . . . . . . . . . . . . . . . . -98dB • OFF-Isolation (100kHz) . . . . . . . . . . . . . . . . . . . . . 95.5dB • Single Supply Operation (VDD) . . . . . . . . . . . . 2.7V to 4.6V • -3dB Bandwidth USB Switches . . . . . . . . . . . . . . . 700MHz The ISL54217 is available in a tiny 12 Ld 2.2mmx1.4mm ultra thin QFN and a 12 Ld 3mmx3mm TQFN package. It operates over a temperature range of -40°C to +85°C. • Available in Tiny 12 Ld µTQFN and TQFN Packages Related Literature • Pb-Free (RoHS Compliant) • Compliant with USB 2.0 Short Circuit Requirements Without Additional External Components • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” Applications • MP3 and other Personal Media Players • Cellular/Mobile Phone Application Block Diagram 3.3V µCONTROLLER VDD ISL54217 C0 4MΩ C1 2DUSB HIGH-SPEED TRANSCEIVER COM - 2D+ L AUDIO CODEC R COM + CLICK/ POP 1D- USB HIGH-SPEED 1kΩ 1D+ TRANSCEIVER 50kΩ VBUS USB/HEADPHONE JACK LOGIC CONTROL 1kΩ 50kΩ GND 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008, 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54217 State Diagram 0 ALL 00 00 SWITCHES OFF 10 01 00 00 0 1 0 01 USB2 00 11 USB1 AUDIO MUTE 10 01 INTERNAL REGISTER VALUE WHEN TRANSISTIONED INTO THIS STATE 11 10 11 1 11 01 AUDIO 11 Pinout (Note 1) 2 R 3 VDD C0 10 LOGIC CONTROL 9 C1 C/P 8 COM - C/P 7 COM + 4 5 6 GND L 11 1D+ 1 12 1D- 2D+ 2D- ISL54217 (12 Ld 2.2mmx1.4mm µTQFN, 12 Ld 3mmx3mm TQFN) TOP VIEW NOTE: 1. ISL54217 Switches Shown for C1 = Logic “1” and C0 = Logic “1”. R and L 50kΩ pull-down resistors and COM- and COM+ 1kΩ Shunts not shown. 2 FN6817.3 May 4, 2009 ISL54217 Truth Table CURRENT CODE LAST CODE SHUNT SWITCHES C1 C0 C1 C0 MODE CLICK/POP AUDIO SHUNTS 1kΩ COM SHUNTS INTERNAL REGISTER 0 0 X X ALL SWITCHES OFF ON OFF 0 0 1 X X USB1 ON OFF 0 1 0 0 0 USB2 ON OFF 0 1 0 0 1 USB2 ON OFF 0 1 0 1 0 USB2 ON OFF 0 1 1 X X AUDIO OFF OFF 1 1 0 1 0 MUTE OFF ON 1 1 0 1 1 MUTE OFF ON 1 NOTE: C0, C1: Logic “0” when ≤ 0.5V, Logic “1” when ≥ 1.4V with VDD in the range of 2.7V to 3.6V. Pin Descriptions PIN NUMBER NAME 1 2D+ 2 L Audio Left Input 3 R Audio Right Input 4 1D- USB1 Differential Input 5 1D+ USB1 Differential Input 6 GND Ground Connection 7 COM+ Voice and Data Common Pin 8 COM- Voice and Data Common Pin 9 C1 Digital Control Input 10 C0 Digital Control Input 11 VDD Power Supply 12 2D- USB2 Differential Input FUNCTION USB2 Differential Input Ordering Information PART MARKING PART NUMBER TEMP. RANGE (°C) PACKAGE (Pb-Free) PKG. DWG. # ISL54217IRUZ-T* (Note 2) GP -40 to +85 12 Ld 2.2mmx1.4mm µTQFN (Tape and Reel) L12.2.2x1.4A ISL54217IRTZ (Note 3) 4217 -40 to +85 12 Ld 3mmx3mm TQFN L12.3x3A ISL54217IRTZ-T* (Note 3) 4217 -40 to +85 12 Ld 3mmx3mm TQFN (Tape and Reel) L12.3x3A ISL54217EVAL1Z Evaluation Board *Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3 FN6817.3 May 4, 2009 ISL54217 Absolute Maximum Ratings Thermal Information VDD to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 5.5V Input Voltages 1D+, 1D-, L, R, 2D+, 2D- . . . . . . . . . . . . . . . . . . . . . . -2V to 5.5V C0, C1 (Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 5.5V Output Voltages COM-, COM+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2V to 5.5V Continuous Current (L, R) . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60mA Peak Current (L, R) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±120mA Continuous Current (1D-, 1D+, 2D-, 2D+) . . . . . . . . . . . . . . . ±40mA Peak Current (1D-, 1D+, 2D-, 2D+) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA ESD Rating: Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>5kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>2kV Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) 12 Ld µTQFN Package (Note 5) . . . . . 155 N/A 12 Ld TQFN Package (Notes 6, 7). . . . 58 1.0 Maximum Junction Temperature (Plastic Package). . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 4.6V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. Signals on C1 and C0 exceeding GND by specified amount are clamped. Limit current to maximum current ratings. 5. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 6. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 7. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VC0H, VC1H = 1.4V, VC0L, VC1L= 0.5V, (Note 8), Unless Otherwise Specified. PARAMETER TEST CONDITIONS TEMP MIN MAX (°C) (Notes 9, 10) TYP (Notes 9, 10) UNITS ANALOG SWITCH CHARACTERISTICS Audio Switches (L, R) Analog Signal Range, VANALOG VDD = 3.0V to 3.6V, Audio Mode (C0 = VDD, C1 = VDD) Full -1.5 - 1.5 V ON-Resistance, rON VDD = 3.0V, Audio Mode (C0 = 1.4V, C1 = 1.4V), ICOMx = 60mA, VL or VR = -0.85V to 0.85V, (see Figure 3, Note 12) +25 - 2.3 2.8 Ω Full - - 3.4 Ω rON Matching Between Channels, ΔrON VDD = 3.0V, Audio Mode (C0 = 1.4V, C1 = 1.4V), ICOMx = 60mA, VL or VR = Voltage at max rON over signal range of -0.85V to 0.85V, (Notes 12, 13) +25 - 0.04 0.25 Ω Full - - 0.26 Ω rON Flatness, rFLAT(ON) VDD = 3.0V, Audio Mode (C0 = 1.4V, C1 = 1.4V), ICOMx = 60mA, VL or VR = -0.85V to 0.85V, (Notes 11, 12) +25 - 0.03 0.05 Ω Full - - 0.07 Ω +25 - 28 - Ω Click/Pop Shunt Resistance, RL, RR VDD = 3.6V, ALL OFF Mode (C0 = 0.5V, C1 = 0.5V), VCOM- or VCOM+ = -0.85V, 0.85V, VL or VR = -0.85V, 0.85V, Measure current into L or R pin and calculate resistance value. USB/DATA Switches (1D+, 1D-, 2D+, 2D-) Analog Signal Range, VANALOG VDD = 2.7V to 4.6V, USB1 mode (C0 = 0V, C1 = VDD) or USB2 Mode (C0 = VDD, C1 = 0V) Full -1 - VDD V ON-Resistance, rON VDD = 2.7V, USB1 mode (C0 = 0.5V, C1 = 1.4V) or USB2 Mode (C0 = 1.4V, C1 = 0.5V), ICOMx = 40mA, VD+ or VD = 0V to 400mV (see Figure 4, Note 12) 25 - 6.2 8 Ω Full - - 10 Ω rON Matching Between Channels, ΔrON VDD = 2.7V, USB1 mode (C0 = 0.5V, C1 = 1.4V) or USB2 Mode (C0 = 1.4V, C1 = 0.5V), ICOMx = 40mA, VD+ or VD-= Voltage at max rON, (Notes 12, 13) 25 - 0.08 0.5 Ω Full - - 0.55 Ω rON Flatness, RFLAT(ON) VDD = 2.7V, USB1 mode (C0 = 0.5V, C1 = 1.4V) or USB2 Mode (C0 = 1.4V, C1 = 0.5V), ICOMx = 40mA, VD+ or VD-= 0V to 400mV, (Notes 11, 12) 25 - 0.26 1 Ω Full - - 1.2 Ω 4 FN6817.3 May 4, 2009 ISL54217 Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VC0H, VC1H = 1.4V, VC0L, VC1L= 0.5V, (Note 8), Unless Otherwise Specified. (Continued) PARAMETER TEST CONDITIONS TEMP MIN MAX (°C) (Notes 9, 10) TYP (Notes 9, 10) UNITS VDD = 3.3V, USB1 mode (C0 = 0.5V, C1 = 1.4V) or USB2 Mode (C0 = 1.4V, C1 = 0.5V), ICOMx = 40mA, VD+ or VD- = 3.3V (see Figure 4, Note 12) +25 - 9.8 20 Ω Full - - 25 Ω OFF Leakage Current, ID+(OFF) or ID-(OFF) VDD = 3.6V, All OFF Mode (C0 = 0.5V, C1 = 0.5V), VCOMor VCOM+ = 0.5V, 0V, VD+ or VD- = 0V, 0.5V, L = R = float 25 -15 0.11 15 nA ON Leakage Current, IDX VDD = 3.3V, USB1 mode (C0 = 0.5V, C1 = 1.4V) or USB2 Mode (C0 = 1.4V, C1 = 0.5V), VD+ or VD- = 2.7V, COM- = COM+ = Float, L and R = float ON-Resistance, rON Full -20 - 20 nA 25 -20 2.4 20 nA Full -25 - 25 nA DPDT DYNAMIC CHARACTERISTICS ALL OFF to USB or USB to All OFF Address Transition Time, tTRANS VDD = 2.7V, RL = 50Ω, CL = 10pF, (see Figure 1) 25 - 175 - ns Audio to USB1 Address Transition Time, tTRANS VDD = 2.7V, RL = 50Ω, CL = 10pF, (see Figure 1) 25 - 12 - µs Break-Before-Make Time Delay, tD VDD = 3.6V, RL = 50Ω, CL = 10pF, (see Figure 2) 25 - 52 - ns Skew, (tSKEWOUT - tSKEWIN) VDD = 3.0V, USB1 mode (C0 = 0V, C1 = VDD) or USB2 Mode (C0 = VDD, C1 = 0V), RL = 45Ω, CL = 10pF, tR = tF = 500ps at 480Mbps, (Duty Cycle = 50%) (see Figure 7) 25 - 75 - ps Total Jitter, tJ VDD =3.0V, USB1 mode (C0 = 0V, C1 = VDD) or USB2 Mode (C0 = VDD, C1 = 0V), RL = 45Ω, CL = 10pF, tR = tF = 500ps at 480Mbps 25 - 210 - ps Rise/Fall Degradation (Propagation Delay), tPD VDD = 3.0V, USB1 mode (C0 = 0V, C1 = VDD) or USB2 Mode (C0 = VDD, C1 = 0V), RL = 45Ω, CL = 10pF, (see Figure 7) 25 - 250 - ps Audio Crosstalk R to COM-, L to COM+ VDD = 3.0V, Audio Mode (C0 = VDD, C1 = VDD), RL = 32Ω, f = 20Hz to 20kHz, VR or VL = 0.707VRMS, (see Figure 6) 25 - -88 - dB Crosstalk (Audio to USB, USB to Audio) VDD = 3.0V, RL = 50Ω, f = 100kHz 25 - -98 - dB OFF-Isolation VDD = 3.0V, RL = 50Ω, f = 100kHz 25 - 95.5 - dB Audio OFF-Isolation (All OFF Mode) VDD = 3.0V, C0 = 0V, C1 = 0V, RL = 32Ω, f = 20Hz to 20kHz 25 - 115 - dB Audio OFF-Isolation (Mute Mode) VDD = 3.0V, C1 = VDD , C0 = 0V, RL = 32Ω, f = 20Hz to 20kHz 25 - 105 - dB Audio OFF-Isolation (Mute Mode) VDD = 3.0V, C1 = VDD , C0 = 0V, RL = 20kΩ, f = 20Hz to 20kHz 25 - 77 - dB Total Harmonic Distortion f = 20Hz to 20kHz, VDD = 3.0V, C0 = VDD, C1 = VDD, L or R = 0.707VRMS (2VP-P), RL = 32Ω 25 - 0.045 - % Total Harmonic Distortion f = 20Hz to 20kHz, VDD = 3.0V, C0 = VDD, C1 = VDD, 5mW into RL = 32Ω 25 - 0.025 - % Click and Pop VDD = 3.3V, Audio Mute (C0 = 0V, C1 = 0V), RL =1kΩ, L or R = 0 to 1.25V DC step or 1.25V to 0V DC step, (see Figure 8) 25 - 75 - µVp Click and Pop VDD = 3.3V, C0, C1 = 0.5Hz Square Wave, RL = 1kΩ , L or R = AC coupled to ground, (see Figure 9) 25 - 520 - µVp USB Switch -3dB Bandwidth Signal = 0dBm, 0.2VDC offset, RL = 50Ω, CL = 5pF 25 - 700 - MHz Audio Switch -3dB Bandwidth Signal = 0dBm, RL = 50Ω, CL = 5pF 25 - 330 - MHz 1D+/1D- OFF Capacitance, C1D+OFF, C1D-OFF f = 1MHz, VDD = 3.0V, C0 = VDD, C1 = VDD, VD- or VD+ = VCOMx = 0V (see Figure 5) 25 - 3 - pF L/R OFF Capacitance, CLOFF, CROFF f = 1MHz, VDD = 3.0V, C0 = 0V, C1 = VDD, L or R = COMx = 0V (see Figure 5) 25 - 5 - pF 5 FN6817.3 May 4, 2009 ISL54217 Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VC0H, VC1H = 1.4V, VC0L, VC1L= 0.5V, (Note 8), Unless Otherwise Specified. (Continued) PARAMETER TEST CONDITIONS TEMP MIN MAX (°C) (Notes 9, 10) TYP (Notes 9, 10) UNITS 2D+/2D- OFF Capacitance, C2D+OFF, C2D-OFF f = 1MHz, VDD = 3.3V, C0 = VDD, C1 = VDD, Tx or Rx = COMx = 0V (see Figure 5) 25 - 3 - pF COM ON Capacitance, CCOM-(ON), CCOM+(ON) f = 1MHz, VDD = 3.0V, USB1 mode (C0 = 0V, C1 = VDD) or USB2 Mode (C0 = VDD, C1 = 0V) (see Figure 5) 25 - 8 - pF Full 2.7 4.6 V POWER SUPPLY CHARACTERISTICS Power Supply Range, VDD Positive Supply Current, IDD (ALL OFF Mode) VDD = 3.6V, C1 = GND, C0 = GND Positive Supply Current, IDD (USB1 Mode) VDD = 3.6V, C1 = GND, C0 = VDD Positive Supply Current, IDD (USB2 Mode) VDD = 3.6V, C1 = VDD, C0 = GND Positive Supply Current, IDD (Audio Mode) VDD = 3.6V, C0 = C1 = VDD) Positive Supply Current, IDD (MUTE Mode) VDD = 3.6V, C1 = VDD, C0 = GND Power OFF COMx Current, ICOMx VDD = 0V, C0 = C1 = Float, COMx = 5.25V 25 Power OFF Logic Current, IC0,IC1 VDD = 0V, C0 = C1 = 5.25V 25 25 - Power OFF D+/D- Current, IXD+, IXD- VDD = 0V, C0 = C1 = Float, XD- = XD+ = 5.25V 25 - 6.2 8 µA Full - - 15 µA 25 - 6.5 8 µA Full - - 15 µA 25 - 6.2 8 µA Full - - 15 µA 25 - 9 14 µA Full - - 20 µA 25 - 6.6 8 µA Full - - 15 µA - - 1 µA - 11 - µA 5 - µA DIGITAL INPUT CHARACTERISTICS C0, C1 Voltage Low, VC0L, VC1L VDD = 2.7V to 3.6V Full - - 0.5 V C0, C1 Voltage High, VC0H, VC1H VDD = 2.7V to 3.6V Full 1.4 - 5.25 V C0, C1 Input Current, IC0L, IC1L VDD = 3.6V, C0 = C1= 0V or Float Full -50 6.2 50 nA C0, C1 Input Current, IC0H, IC1H VDD = 3.6V, C0 = C1= 3.6V Full -2 1.6 2 µA C0, C1 Pull-Down Resistor, RCx VDD = 3.6V, C0 = C1= 3.6V, Measure current into C0 or C1 pin and calculate resistance value. Full - 4 - MΩ NOTES: 8. VLOGIC = Input voltage to perform proper function. 9. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 10. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 11. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 12. Limits established by characterization and are not production tested. 13. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON value, between L and R or between 1D+ and 1D- or between 2D+ and 2D-. 6 FN6817.3 May 4, 2009 ISL54217 Test Circuits and Waveforms VC0,C1 LOGIC INPUT VC0,C1 50% SWITCH INPUT VINPUT C VINPUT tOFF VOUT SWITCH INPUT COMx C0,C1 VOUT 90% 90% SWITCH OUTPUT VDD tr < 20ns tf < 20ns LOGIC INPUT 0V CL 10pF RL 50Ω GND tON Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for all switches. CL includes fixture and stray capacitance. RL V OUT = V (INPUT) -----------------------R L + r ON FIGURE 1A. ADDRESS tTRANS MEASUREMENT POINTS FIGURE 1B. ADDRESS tTRANS TEST CIRCUIT FIGURE 1. SWITCHING TIMES VDD LOGIC INPUT 2D- OR 2D+ VC0 1D- OR 1D+ VINPUT VC1 SWITCH OUTPUT C 90% GND LOGIC INPUT 0V CL 10pF RL 50Ω C0, C1 VOUT VOUT COMx L OR R tD Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 2A. MEASUREMENT POINTS FIGURE 2B. TEST CIRCUIT FIGURE 2. BREAK-BEFORE-MAKE TIME VDD VDD C C rON = V1/40mA rON = V1/60mA D- OR D+ COMx VD- OR D+ VL OR R V1 60mA C0 VCOH C1 VC1H V1 40mA L OR R 7 VC0L AND C1 VC1H OR COMx GND GND Repeat test for all switches. FIGURE 3. AUDIO rON TEST CIRCUIT C0 VC0H AND VC1L Repeat test for all switches. FIGURE 4. USB rON TEST CIRCUIT FN6817.3 May 4, 2009 ISL54217 Test Circuits and Waveforms (Continued) VDD VDD CTRL CTRL SIGNAL GENERATOR AUDIO OR USB L OR R 32Ω COMx VCx VCx IMPEDANCE ANALYZER C C 0V OR FLOAT VCxL OR VCxH COMx R or L COMx ANALYZER GND NC GND 32Ω Repeat test for all switches. FIGURE 5. CAPACITANCE TEST CIRCUIT FIGURE 6. AUDIO CROSSTALK TEST CIRCUIT VDD tri C 90% DIN+ 10% 50% tskew_i DIN- 90% 50% C1 VDD COM+ DIN- 15.8Ω OUT+ D+ 143Ω 90% OUT- VDD DIN+ tfi tro OUT+ C0 15.8Ω 10% 10% 0V CL COM- OUT- DCL 143Ω 45Ω 45Ω 50% tskew_o GND |tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals. 50% 90% |tfo - tfi| Delay Due to Switch for Falling Input and Falling Output Signals |tskew_0| Change in Skew through the Switch for Output Signals. |tskew_i| Change in Skew through the Switch for Input Signals. 10% tf0 FIGURE 7A. MEASUREMENT POINTS FIGURE 7B. TEST CIRCUIT FIGURE 7. SKEW TEST 3.3V AUDIO PRECISION SYSTEM II CASCADE ANALYZER CHA CHB VDD COMCOM+ CLICK AND POP L R RLOAD RLOAD C0 C1 GND 0V TO 1.25V DC STEP OR 1.25V TO 0V DC STEP 0V 0V ALL OFF MODE Set Audio Analyzer for Peak Detection, 32 Samples/Sec, Aweighted Filter, Manual Range 1X/Y, Units to dBV FIGURE 8. CLICK AND POP TEST CIRCUIT 8 FN6817.3 May 4, 2009 ISL54217 Test Circuits and Waveforms (Continued) 3.3V AUDIO PRECISION SYSTEM II CASCADE ANALYZER CHA C VDD CHB COM- L CLICK AND POP COM+ RLOAD R RLOAD GND C0, C1 0V TO VDD SQUARE WAVE Set Audio Analyzer for Peak Detection, 32 Samples/Sec, Aweighted Filter, Manual Range 1X/Y, Units to dBV FIGURE 9. CLICK AND POP TEST CIRCUIT Block Diagram 3.3V µCONTROLLER VDD ISL54217 C0 4MΩ C1 2DUSB HIGH-SPEED TRANSCEIVER #2 COM - 2D+ COM + L CLICK/ R POP AUDIO CODEC 1D- USB 1kΩ 1D+ HIGH-SPEED TRANSCEIVER #1 OR UART VBUS USB/HEADPHONE JACK LOGIC CONTROL 50kΩ 50kΩ GND TRANSCEIVER Detailed Description The ISL54217 device consists of dual SP3T (single pole/triple throw) analog switches. It operates from a single DC power supply in the range of 2.7V to 4.6V. It was designed to function as differential 3-to-1 multiplexer to select between two different USB differential data signals and audio L and R stereo signals. It comes in a tiny µTQFN and TQFN packages for use in MP3 players, PDAs, cell phones, and other personal media players. 9 A device consists of two 2.3Ω audio switches and four 6.2Ω USB switches. The audio switches can accept signals that swing below ground. They were designed to pass audio left and right stereo signals, that are ground referenced, with minimal distortion. The USB switches were designed to pass high-speed USB differential data signals with minimal edge and phase distortion. The ISL54217 was specifically designed for MP3 players, personal media players and cellphone applications that need FN6817.3 May 4, 2009 ISL54217 to combine the stereo audio and USB data channels into a single shared connector, thereby saving space and component cost. The Typical application block diagram of this functionality is previously shown. The ISL54217 contains two logic control pins (C1 and C0) that determine the state of the device. The part has the following five states or modes of operation: All SWITCHES OFF; USB1; USB2; Audio; and Audio Mute. These states are discussed in detail in “Logic Control” on page 10. A detailed description of the various types of switches are provided in “Audio Switches” beginning on page 10. Audio Switches The two audio switches (L, R) are 2.3Ω switches that can pass signals that swing below ground. Over a signal range of ±1V (0.707Vrms) with VDD > 2.7V, these switches have an extremely low rON resistance variation. They can pass ground referenced audio signals with very low distortion (<0.05% THD+N) when delivering 15.6mW into a 32Ω headphone speaker load. See Figures 20, 21, 22, 23 and 24 THD+N performance curves. Crosstalk between the L and R audio switches over the frequency range of 20Hz to 20kHz when driving a 32Ω load is < -88dB. These switches have excellent off-isolation > 105dB over the audio band when connected to 32Ω loads and 77dB when connected to 20kΩ loads (In Audio Mute mode). See Figures 25 and 26 in “Typical Performance Curves” section beginning on page 12. The audio drivers should be connected at the L and R side of the switch (pins 2 and 3) and the speaker loads should be connected at the COM side of the switch (pins 7 and 8). The switches have click and pop circuitry on the L and R side that is activated when the part comes out of Audio mode by taking the C1 and C0 logic pins low (All OFF mode). The ISL54217 should be put in this mode before powering down or powering up of the audio CODEC drivers. In this mode the audio, USB1, USB2 switches will be OPEN (OFF) and the audio click and pop circuitry will be ON. The high off-isolation of the audio switches along with the click and pop circuitry will isolate the transients generated during power-up and power down of the audio CODECs from getting through to the headphones thus eliminating click and pop noise in the headphones. See the “AC Coupled click and pop operation” on page 12. The audio switches are active (turned ON) whenever the C1 and C0 logic pins are logic “1” (High). USB Switches The four USB switches (1D+, 1D-, 2D+, 2D-) are 6.2Ω bidirectional switches that were specifically designed to pass high-speed USB differential data signals in the range of 0V to 400mV. The switches have low capacitance and high bandwidth to pass USB high-speed signals (480Mbps) with 10 minimum edge and phase distortion to meet USB 2.0 signal quality specifications. See Figures 27 and 28 for High-speed Eye Pattern taken with switch in the signal path. These switches can also swing rail to rail and pass USB full-speed signals (12Mbps) with minimal distortion. See Figure 29 for Full-speed Eye Pattern taken with switch in the signal path. The maximum normal operating signal range for the USB switches is from -1V to VDD. The signal voltage at D- and D+ should not be allow to exceed the VDD voltage rail or go below ground by more than -1V for normal operation. However in the event that the USB 5.25V VBUS voltage were shorted to one or both of the COM pins, the ISL54217 has fault protection circuitry to prevent damage to the ISL54217 part. The fault circuitry allows the signal pins (COM-, COM+, 1D-, 1D+, 2D-, 2D+, L and R) to be driven up to 5.25V while the VDD supply voltage is in the range of 0V to 4.6V. This fault condition causes no stress to the IC. In addition, when VDD is at 0V (ground) all switches are OFF and the fault voltage is isolated from the other side of the switch. When VDD is in the range of 2.7V to 4.6V the fault voltage will pass through to the output of an active switch channel. Note: During the fault condition normal operation is not guaranteed until the fault condition is removed. The USB (1D+ and 1D-) switches are active (turned ON) whenever the C1 is logic “0” (Low) and C0 is logic “1” (High). The USB (2D+ and 2D-) switches are active (turned ON) whenever the C1 is logic “1” (High) and C0 is logic “0” (Low) provided the last state was not the Audio or Audio Mute state. ISL54217 Operation The discussion that follows will discuss using the ISL54217 in the “Block Diagram” on page 9. LOGIC CONTROL The state of the ISL54217 device is determined by the voltage at the C1 pin (pin 9) and the C0 pin (pin 10). The part has five states or modes of operation. The All SWITCHES OFF mode, USB1 mode, USB2 mode, Audio mode and Audio Mute mode. Refer to “Truth Table” on page 3 and “State Diagram” on page 2 of data sheet. The C1 pin and C0 pin are internally pulled low through 4MΩ resistors to ground and can be tri-stated or left floating. The C1 pin and C0 pin can be driven with a voltage that is higher than the VDD supply voltage. They can be driven up to 5.25V with the VDD supply in the range of 2.7V to 4.6V. Driving the logic higher than the supply rail will cause the logic current to increase. With VDD = 2.7V and VLOGIC = 5.25V, ILOGIC current is approximately 5.5µA. FN6817.3 May 4, 2009 ISL54217 Logic Control Voltage Levels With VDD in the range of 2.7V to 3.6V the logic levels are: C1, C0 = Logic “0” (Low) when ≤ 0.5V or Floating. C1, C0 = Logic “1” (High) when ≥ 1.4V cellphone USB transceiver #1 are connected and digital data will be able to be transmit back and forth. USB2 Mode If the C1 pin = Logic “0” and C0 pin = Logic “0” the part will be in the ALL SWITCHES OFF mode. In this mode the 2Dand 2D+ USB switches, the L and R audio switches and the 1D- and 1D+ USB switches will be OFF (high impedance). If the C1 pin = Logic “1” and C0 pin = Logic “0” the part will be in the USB2 mode provided that the last state was not the Audio or Audio Mute state. In the USB2 mode the 2D- and 2D+ 6.2Ω USB switches will be ON and audio switches and the 1D- and 1D+ USB switches will be OFF (high impedance). The audio click and pop shunt circuitry will be activated (ON) and the 1kΩ COM shunt resistors will be disconnected (OFF). The audio L and R click and pop shunt circuitry will be activated and the 1kΩ COM shunt resistors will be disconnected (OFF). Before powering down or powering up of the audio CODECs drivers the ISL54217 should be put in the ALL SWITCHES OFF mode. In this mode transients present at the L and R signal pins due to the changing DC voltage of the audio drivers will not pass to the headphones, preventing clicks and pops in the headphones. See the “AC Coupled click and pop operation” on page 12. When a USB cable from a computer or USB hub is connected at the common connector, the μcontroller will route the incoming USB signal to USB transceiver section #2 by taking the C1 pin “High” and the C0 pin “Low” putting the ISL54217 part into the USB2 mode. In USB2 mode the computer or USB hub transceiver and the MP3 player or cellphone USB transceiver #2 are connected and digital data will be able to be transmit back and forth. It is recommended that when transitioning from USB1 to USB2 or from USB2 to USB1 that you always pass through the All Switches OFF state. Audio MUTE Mode ALL SWITCHES OFF Mode Audio Mode If the C1 pin = Logic “1” and C0 pin = Logic “1” the part will be in the Audio mode. In Audio mode the L (left) and R (right) 2.3Ω audio switches are ON. The 1D- and 1D+ 6.2Ω USB switches and 2D- and 2D+ 6.2Ω USB switches will be OFF (high impedance). The audio click and pop circuitry is de-activated. The 1kΩ shunts on the COM side of the switch will be disconnected (OFF). When a headphone is plugged into the common connector, the µcontroller will drive the C1 and C0 logic pins “High” putting the part in the audio mode. In the audio mode, the audio drivers of the player can drive the headphones and play music. USB1 Mode If the C1 pin = Logic “0” and C0 pin = Logic “1” the part will go into USB1 mode. In USB1 mode the 1D- and 1D+ 6.2Ω switches are ON. The L and R 2.3Ω audio switches and 2Dand 2D+ 6.2Ω USB switches will be OFF (high impedance). The audio L and R click and pop shunt circuitry will be activated and the 1kΩ COM shunt resistors will be disconnected (OFF). When a USB cable from a computer or USB hub is connected at the common connector, the µcontroller will route the incoming USB signal to USB transceiver section #1 by taking the C1 pin “Low” and the C0 pin “High” putting the ISL54217 part into the USB1 mode. In USB1 mode the computer or USB hub transceiver and the MP3 player or 11 If the C1 pin = Logic “1” and C0 pin = Logic “0” the part will be in the Audio MUTE mode provided that the last state was the Audio state. In the audio MUTE mode the 2D- and 2D+ USB switches, the L and R audio switches and the 1D- and 1D+ USB switches will be OFF (high impedance). The audio click and pop shunt circuitry will be de-activated and the 1kΩ COM shunt resistors will be connected (ON). Note: 1kΩ COM shunt resistors are only ON when in Audio MUTE mode. The 1kΩ shunts provide 77dB of off-isolation when driving 10kΩ to 20kΩ amplifier inputs. Logic Control Timing Between C1 and C0 The ISL54217 has a unique logic control architecture. The part has five different logic states but only two external logic control pins, C1 and C0. Refer to “State Diagram” on page 2 and “Truth Table” on page 3. The following state transitions require both C1 and C0 logic control bits to change their logic levels in unison: All OFF(C1 = 0, C0 = 0) -----> Audio (C1 = 1, C0 =1) Audio (C1 = 1, C0 = 1) -----> All OFF (C1 = 0, C0 = 0) Audio Mute (C1 = 1, C0 = 0) -----> USB1 (C1 = 0, C0 = 1) The delay time between transition of these bits must be < 100ns to ensure that you directly move between these states without momentarily transitioning to one of the other states. For example, if you are going from the “All OFF” state to the “Audio” state and C0 does not go high until 100ns after C1 went high you will momentarily transition to the “USB2” state. FN6817.3 May 4, 2009 ISL54217 Any signals connected at the USB2 signal lines will momentarily get passed through to the COM outputs. be coupled into the speaker load through the DC blocking capacitor (see the “Block Diagram” on page 9). Delay time between C1 and C0 must be < 100ns and should be controlled by logic control drivers with well behaved monotonic transitions from High to Low and Low to High and with typical logic family rise and fall times of 1ns to 6ns. When a driver is OFF and suddenly turned ON the rapidly changing DC bias voltage at the output of the driver will cause an equal voltage at the input side of the switch due to the fact that the voltage across the blocking capacitor cannot change instantly. If the switch is in the Audio mode or there is no low impedance path to discharge the blocking capacitor voltage, before turning the audio switch ON, a transient discharge will occur in the speaker, generating a click/pop noise. POWER The power supply connected at VDD (pin 11) provides power to the ISL54217 part. Its voltage should be kept in the range of 2.7V to 4.6V. In a typical application VDD will be in the range of 2.7V to 4.3V and will be connected to the battery or LDO of the MP3 player or cellphone. A 0.01µF or 0.1µF decoupling capacitor should be connected from the VDD pin to ground to filter out any power supply noise from entering the part. The capacitor should be located as close to the VDD pin as possible. Before power-up and power-down of the ISL54217 part the C1 and C0 control pins should be driven to ground or tri-stated. This will put the switch in the ALL SWITCHES OFF state, which turns all switches OFF and activate the click and pop circuitry. This will minimize transients at the speaker loads during power-up and power-down of the ISL54217 device. See Figure 32 in the “Typical Performance Curves” section. AC COUPLED CLICK AND POP OPERATION Single supply audio drivers have their signal biased at a DC offset voltage, usually at 1/2 the DC supply voltage of the driver. As this DC bias voltage comes up or goes down during power-up or power-down of the driver, a transient can Proper elimination of a click/pop transient at the speaker loads while powering up or down of the audio drivers requires that the ISL54217 have its click/pop circuitry activated by putting the part in the ALL SWITCHES OFF mode. This allows the transients generated by the audio drivers to be discharged through the click and pop shunt circuitry. Once the driver DC bias has reached VDD/2 and the transient on the switch side of the DC blocking capacitor has been discharged to ground through the click/pop shunt circuitry, the audio switches can be turned ON and connected through to the speaker loads without generating any undesirable click/pop noise in the speakers. With a typical DC blocking capacitor of 220µF and the click/pop shunt circuitry designed to have a resistance of 20Ω to 70Ω, allowing a 100ms wait time to discharge the transient before placing the switch in the Audio mode will prevent the transient from getting through to the speaker load. See Figures 30 and 31 in the “Typical Performance Curves” section. Typical Performance Curves TA = +25°C, Unless Otherwise Specified 2.95 2.90 2.60 ICOM = 60mA 2.58 2.85 rON (Ω) 2.80 rON (Ω) ICOM = 60mA 2.75 2.70 VDD = 3.0V 2.56 VDD = 3.3V 2.54 VDD = 3.6V 2.65 2.60 2.52 VDD = 2.7V VDD = 4.0V 2.55 2.45 -1.5 2.50 VDD = 3.6V 2.50 VDD = 4.6V VDD = 4.6V -1.0 -0.5 0 VCOM (V) 0.5 1.0 1.5 FIGURE 10. AUDIO ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 12 2.48 -1.5 -1.0 -0.5 0 VCOM (V) 0.5 1.0 1.5 FIGURE 11. AUDIO ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) 18 4.0 ICOM = 60mA +85°C 16 3.5 VDD = 3.0V 14 3.0 VDD = 3.6V 10 rON (Ω) rON (Ω) 12 8 6 +25°C 2.5 2.0 -40°C 4 1.5 2 VDD = 3.0V ICOM = 60mA VDD = 4.6V 0 -1.5 -0.5 0.5 1.5 VCOM (V) 2.5 3.5 1.0 -1.5 4.6 FIGURE 12. AUDIO ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 0 VCOM (V) 16 14 14 12 12 10 10 8 1.0 1.5 VDD = 3.3V ICOM = 60mA 8 6 6 +85°C 4 +85°C 4 +25°C +25°C 2 2 -40°C 0 -1.5 -1.0 -0.5 -40°C 0 0.5 1.0 VCOM (V) 1.5 2.0 2.5 0 -1.5 3.0 FIGURE 14. AUDIO ON-RESISTANCE vs SWITCH VOLTAGE vs TEMPERATURE -0.5 0.5 1.5 VCOM (V) 2.5 3.6 FIGURE 15. AUDIO ON-RESISTANCE vs SWITCH VOLTAGE vs TEMPERATURE 6.7 6.6 0.5 18 VDD = 3.0V ICOM = 60mA rON (Ω) rON (Ω) -0.5 FIGURE 13. AUDIO ON-RESISTANCE vs SWITCH VOLTAGE vs TEMPERATURE 18 16 -1.0 9 ICOM = 40mA VDD = 2.7V ICOM = 40mA VDD = 2.7V +85°C 8 6.5 7 VDD = 3.3V rON (Ω) rON (Ω) 6.4 6.3 VDD = 3.0V 6.2 VDD = 3.3V 6.1 +25°C 6 -40°C 5 6.0 VDD = 4.6V 5.9 5.8 0 0.05 0.10 0.15 0.20 0.25 VCOM (V) 4 VDD = 4.0V 0.30 0.35 0.40 FIGURE 16. USB ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 13 3 0 0.05 0.10 0.15 0.20 0.25 VCOM (V) 0.30 0.35 0.40 FIGURE 17. USB ON-RESISTANCE vs SWITCH VOLTAGE vs TEMPERATURE FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) 9 16 VDD = 3.3V ICOM = 40mA +85°C 8 VDD = 3.3V ICOM = 40mA 14 12 +25°C rON (Ω) rON (Ω) 7 6 +85°C 10 8 +25°C -40°C 5 6 -40°C 4 3 0 4 0.05 0.10 0.15 0.20 0.25 VCOM (V) 0.30 0.35 2 0.40 FIGURE 18. USB ON-RESISTANCE vs SWITCH VOLTAGE vs TEMPERATURE 0 0.5 1.0 1.5 2.0 VCOM (V) 2.5 3.0 3.3 FIGURE 19. USB ON-RESISTANCE vs SWITCH VOLTAGE vs TEMPERATURE 0.032 0.056 RLOAD = 32Ω VLOAD = 0.707VRMS 0.055 0.031 RLOAD = 32Ω PLOAD = 5mW 0.054 VDD = 3.0V 0.030 VDD = 3.6V 0.029 VDD = 2.7V 0.052 THD+N (%) THD+N (%) 0.053 0.051 VDD = 4V 0.050 0.049 VDD = 4.6V VDD = 3.3V VDD = 3.6V 0.028 VDD = 4.0V 0.027 VDD = 4.6V 0.026 0.048 0.025 0.047 0.046 20 50 100 200 500 1k 2k FREQUENCY (Hz) 5k 0.024 20 10k 20k 0.070 PEAK-TO-PEAK VOLTAGES AT LOAD 0.060 0.055 2.5VP-P 5k 10k 20k RLOAD = 32Ω FREQ = 1kHz VDD = 3V 0.050 0.055 0.045 2VP-P 0.050 0.045 THD+N (%) THD+N (%) 200 500 1k 2k FREQUENCY (Hz) 0.065 RLOAD = 32Ω VDD = 3V 0.060 1.5VP-P 0.040 0.035 1.13VP-P 0.030 0.040 0.035 0.030 0.025 0.020 0.025 0.015 1VP-P 0.020 0.010 510mVP-P 0.015 0.010 20 100 FIGURE 21. THD+N vs SUPPLY VOLTAGE vs FREQUENCY FIGURE 20. THD+N vs SUPPLY VOLTAGE vs FREQUENCY 0.065 50 50 100 200 500 1k 2k FREQUENCY (Hz) 0.005 5k 10k 20k FIGURE 22. THD+N vs SIGNAL LEVELS vs FREQUENCY 14 0 0.5 1.0 1.5 2.0 OUTPUT VOLTAGE (VP-P) 2.5 FIGURE 23. THD+N vs OUTPUT VOLTAGE FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) -60 0.09 0.08 RLOAD = 32Ω -70 -80 0.07 FREQ = 1kHz VDD = 3V -90 -100 CROSSTALK (dB) 0.06 0.05 -110 -120 0.04 -130 0.03 -140 -150 0.02 -160 0.01 0 -170 0 5 10 15 20 OUTPUT POWER (mW) 25 -180 20 30 50 100 200 500 1k 2k FREQUENCY (Hz) 5k 10k 20k FIGURE 25. AUDIO CHANNEL-TO-CHANNEL CROSSTALK FIGURE 24. THD+N vs OUTPUT POWER -60 -65 -70 VDD = 3.3V VSIGNAL = 0.707VRMS AUDIO MUTE MODE RL = 20kΩ -75 -80 OFF- ISOLATION (dB) THD+N (%) VDD = 3V RLOAD = 32Ω VSIGNAL = 0.707VRMS RL = 1kΩ -85 -90 -95 -100 RL = 32Ω -105 -110 -115 -120 -125 -130 20 50 100 200 500 1k 2k FREQUENCY (Hz) 5k 10k 20k FIGURE 26. OFF-ISOLATION AUDIO SWITCH vs LOADING vs FREQUENCY 15 FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VDD = 2.7V VOLTAGE SCALE (0.1V/DIV) USB NEAR END MASK TIME SCALE (0.2ns/DIV) FIGURE 27. EYE PATTERN: 480Mbps WITH USB SWITCHES IN THE SIGNAL PATH 16 FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VDD = 2.7V VOLTAGE SCALE (0.1V/DIV) FAR END MASK TIME SCALE (0.2ns/DIV) FIGURE 28. EYE PATTERN: 480Mbps WITH USB SWITCHES IN THE SIGNAL PATH 17 FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VOLTAGE SCALE (0.5V/DIV) VDD = 2.7V TIME SCALE (10ns/DIV) C1, C0 2V/DIV C1, C0 2V/DIV VDD/2 VDD/2 RIN 2V/DIV 200mV/DIV ROUT 50mV/DIV TIME (s) 100ms/DIV FIGURE 30. 32Ω AC COUPLED CLICK/POP REDUCTION 18 VOLTAGE (V) VOLTAGE (V) FIGURE 29. EYE PATTERN: 12Mbps USB SIGNAL WITH USB SWITCHES IN THE SIGNAL PATH LIN 2V/DIV 200mV/DIV LOUT 50mV/DIV TIME (s) 100ms/DIV FIGURE 31. 1kΩ AC COUPLED CLICK/POP REDUCTION FN6817.3 May 4, 2009 ISL54217 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) 1 VDD 1V/DIV USB SWITCH NORMALIZED GAIN (dB) VOLTAGE (V) 0 VIN = 1.5V OR 0V C1 = C0 = 0V VOUT 10mV/DIV -1 -2 -3 -4 RL = 50Ω -5 TIME (s) 200ms/DIV VIN = 0.2VP-P TO 2VP-P 1M FIGURE 32. POWER-UP/POWER-DOWN CLICK AND POP TRANSIENT 1G FIGURE 33. FREQUENCY RESPONSE -20 -10 RL = 50Ω VIN = 0.2VP-P to 2VP-P RL = 50Ω VIN = 0.2VP-P to 2VP-P -30 NORMALIZED GAIN (dB) -40 NORMALIZED GAIN (dB) 10M 100M FREQUENCY (Hz) -60 -80 -100 -50 -70 -90 -110 -120 -140 0.001 0.01 0.10 1M 10M FREQUENCY (Hz) 100M 500M FIGURE 34. OFF-ISOLATION USB SWITCHES -130 0.001 0.01 0.10 1M 10M 100M 500M FREQUENCY (Hz) FIGURE 35. OFF-ISOLATION AUDIO SWITCHES Die Characteristics SUBSTRATE POTENTIAL (Powered Up) GND (Tie TQFN paddle to ground or float) TRANSISTOR COUNT 837 PROCESS Submicron CMOS All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 19 FN6817.3 May 4, 2009 ISL54217 Package Outline Drawing L12.3x3A 12 LEAD THIN QUAD FLAT NO LEAD PLASTIC PACKAGE Rev 0, 09/07 3.00 0.5 BSC A B 6 12 10 PIN #1 INDEX AREA 6 PIN 1 INDEX AREA 1 4X 1.45 3.00 9 7 3 0.10 M C A B (4X) 0.15 4 6 0.25 +0.05 / -0.07 4 12X 0 . 4 ± 0 . 1 TOP VIEW BOTTOM VIEW SEE DETAIL "X" 0.10 C 0 . 75 C BASE PLANE ( 2 . 8 TYP ) 1.45 ) SEATING PLANE 0.08 C ( SIDE VIEW 0.6 C 0 . 50 0 . 2 REF 5 0 . 00 MIN. 0 . 05 MAX. 0 . 25 TYPICAL RECOMMENDED LAND PATTERN DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.18mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. 20 FN6817.3 May 4, 2009 ISL54217 Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN) L12.2.2x1.4A D 6 INDEX AREA 2X A B 12 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS N E 0.10 C 1 2X 2 0.10 C MIN NOMINAL A 0.45 A1 - A3 TOP VIEW 0.10 C C A1 A SYMBOL 0.05 C LEADS COPLANARITY SIDE VIEW MAX NOTES 0.50 0.55 - - 0.05 - 0.127 REF - b 0.15 0.20 0.25 5 D 2.15 2.20 2.25 - E 1.35 1.40 1.45 - e 0.40 BSC - k 0.20 - - - L 0.35 0.40 0.45 - N 12 2 Nd 3 3 Ne 3 3 θ 0 - 12 4 Rev. 0 12/06 NOTES: (DATUM A) 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. PIN #1 ID 1 2. N is the number of terminals. NX L 2 3. Nd and Ne refer to the number of terminals on D and E side, respectively. e Ne 4. All dimensions are in millimeters. Angles are in degrees. (DATUM B) NX b 5 0.10 M C A B 0.05 M C Nd 3 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Maximum package warpage is 0.05mm. 8. Maximum allowable burrs is 0.076mm in all directions. BOTTOM VIEW 9. Same as JEDEC MO-255UABD except: No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. CL NX (b) 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. (A1) L 5 1.50 e SECTION "C-C" C C TERMINAL TIP 2.30 1 2 0.40 3 0.45 (12x) 0.25 (12x) 0.40 TYPICAL RECOMMENDED LAND PATTERN 21 10 FN6817.3 May 4, 2009