NEC Express5800/B120g-h System Configuration Guide Introduction This document contains product and configuration information that will enable you to configure your system. The guide will ensure fast and proper configuration of your NEC Express5800 server. April 25, 2016 Revision 1.0 NEC Corporation SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Contents TECHNICAL SPECIFICATION ........................................................................................ 3 Key Features .......................................................................................................................................... 3 Specification .......................................................................................................................................... 3 EXTERNAL VIEWS ......................................................................................................... 6 Front View .............................................................................................................................................. 6 CONFIGURATION DIAGRAM ......................................................................................... 6 EXPANSION SLOT .......................................................................................................... 7 SERVER CONFIGURATION ........................................................................................... 8 1 2 3 4 5 6 Base Models ................................................................................................................................... 8 2nd Processor ................................................................................................................................ 8 Memory ........................................................................................................................................... 9 3.1 Memory Configuration.......................................................................................................... 9 Internal Drives .............................................................................................................................. 10 4.1 Drive and RAID Configuration ........................................................................................... 10 4.2 Internal Drive Configuration ............................................................................................... 10 I/O Expansion Card ...................................................................................................................... 11 5.1 Network Interface Controller .............................................................................................. 11 5.2 External Storage Controller ............................................................................................... 13 Other Add-in Components .......................................................................................................... 13 6.1 Trusted Platform Module Kit .............................................................................................. 13 REFERENCES............................................................................................................... 14 Boot Mode Setting .............................................................................................................................. 14 Server Management ............................................................................................................................ 15 OS Support Matrix for PCI Cards and Embedded Controllers ....................................................... 16 Support Matrix for Adapters and Network Interconnect Devices .................................................. 17 Supported PCI Cards and Installable Slots ...................................................................................... 18 Copyright Notice and Liability Disclaimer ........................................................................................ 19 REVISION HISTORY ..................................................................................................... 20 NEC Corporation Revision 1.0 – April, 2016 2 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Technical Specification Key Features High performance with the latest Intel® Xeon® processor E5-2600 v4 product family Up to 1152 GB of high speed DDR4-2400 memory Full manageability by integrated EXPRESSSCOPE Engine 3 Specification (1/2) Model B120g-h Part Number N8400-250F N8400-251F N8400-252F Type Intel® Xeon® processor E5-2620 v4 Intel® Xeon® processor E5-2650 v4 Intel® Xeon® processor E5-2667 v4 Clock speed 2.10 GHz 2.20 GHz 3.20 GHz Number of Processors 1 to 2 Cache 20 MB 30 MB 25 MB Cores and Threads 8C-16T 12C-24T 8C-16T Processor Chipset Memory Internal Storage Intel® C612 Chipset Type DDR4-2400 Registered DIMM (4/8/16/32GB) DDR4-2400 TSV Registered DIMM (64GB) Standard Capacity 0 GB Maximum Capacity 1152 GB (18 x 64 GB) Memory protection ECC, x4 SDDC, Memory Lockstep, Memory Sparing , Memory 1 Mirroring Standard Capacity 0 GB Maximum Capacity SATA SSD: 800 GB (2 x 400GB) - Disk Controller SATA: 6Gb/s (Integrated) - RAID RAID 0/1 (Integrated) - Hot Plug Not supported - 1 Disk Drive Bays 2 [2] Expansion Slots Standard Total: 3 slots available 1 Type 1 mezzanine 1 Type 2 mezzanine 1 PCIe for a flexible integrated NIC Video Controller (VRAM) Integrated in Server Management Controller (32MB) Resolution / Color 640 x 480 – 1600 x 1200 / 16.7M 2 Interfaces 1 SUV (1 front) Server Management EXPRESSSCOPE Engine 3 Maximum Power Consumption (VDC) 364 Watt Dimensions (W x D x H ) 51.6 x 515.4 x 180.7 mm / 2.0 x 20.3 x 7.1 in Weight (Minimum / Maximum) 2kg / 5 kg, 4.41 / 13.23 lbs. Enclosures Blade Enclosure M, Blade Enclosure-H v2 Temperature, Relative Humidity (non-condensing) Operating: 5° to 40° C / 41° to 104° F , 20 to 80% Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80% Regulatory and Safety FCC, UL, CB, CE, BSMI, CCC, RoHS, WEEE Operating Systems and Virtualization Software Microsoft® Windows Server® 2012 R2 Standard Microsoft® Windows Server® 2012 R2 Datacenter NEC Corporation 409 Watt 3 Revision 1.0 – April, 2016 483 Watt 3 3 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Model B120g-h Operating Systems and Virtualization Software (contd.) VMware ESXi 5.5 Update 3 or later VMware ESXi 6.0 Update 1 or later 1 To configure memory sparing or mirroring, contact your sales representative. 2 Maximum resolution and color available via EXPRESSSCOPE Engine 3 remote console is 1280 x 1024 / 65K colors. 3 Up to 35°C (95°F) when a dual processor configuration with E5-2667 v4, E5-2698 v4 or E5-2699 v4. 4 For Linux support, contact your sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html (2/2) Model B120g-h Part Number Processor N8400-253F N8400-254F N8400-255F Type Intel® Xeon® processor E5-2690 v4 Intel® Xeon® processor E5-2698 v4 Intel® Xeon® processor E5-2699 v4 Clock speed 2.60 GHz 2.20 GHz 2.20 GHz Number of Processors 1 to 2 Cache 35 MB 50 MB 55 MB Cores and Threads 14C-28T 20C-40T 22C-44T Chipset Memory Intel® C612 Chipset Type DDR4-2400 Registered DIMM (4/8/16/32GB) DDR4-2400 TSV Registered DIMM (64GB) Standard Capacity 0 GB Maximum Capacity 1152 GB (18 x 64 GB) Memory protection ECC, x4 SDDC, Memory Lockstep, Memory Sparing , Memory 1 Mirroring Standard Capacity 0 GB Maximum Capacity SATA SSD: 800 GB (2 x 400GB) - Disk Controller SATA: 6Gb/s (Integrated) - RAID RAID 0/1 (Integrated) - Hot Plug Not supported - Disk Drive Bays 2 [2] - Expansion Slots Standard Total: 3 slots available 1 Type 1 mezzanine 1 Type 2 mezzanine 1 PCIe for a flexible integrated NIC Video Controller (VRAM) Integrated in Server Management Controller (32MB) Resolution / Color 640 x 480 – 1600 x 1200 / 16.7M Internal Storage 1 2 Interfaces 1 SUV (1 front) Server Management EXPRESSSCOPE Engine 3 Maximum Power Consumption (VDC) 485 Watt Dimensions (W x D x H ) 51.6 x 515.4 x 180.7 mm / 2.0 x 20.3 x 7.1 in Weight (Minimum / Maximum) 2kg / 5 kg, 4.41 / 13.23 lbs. Enclosures Blade Enclosure M, Blade Enclosure-H v2 Temperature, Relative Humidity (non-condensing) Operating: 5° to 40° C / 41° to 104° F , 20 to 80% Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80% Regulatory and Safety FCC, UL, CB, CE, BSMI, CCC, RoHS, WEEE Operating Systems and Virtualization Software Microsoft® Windows Server® 2012 R2 Standard Microsoft® Windows Server® 2012 R2 Datacenter NEC Corporation 492 Watt 3 Revision 1.0 – April, 2016 514 Watt 3 4 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Model B120g-h Operating Systems and Virtualization Software (contd.) VMware ESXi 5.5 Update 3 or later VMware ESXi 6.0 Update 1 or later 1 To configure memory sparing or mirroring, contact your sales representative. 2 Maximum resolution and color available via EXPRESSSCOPE Engine 3 remote console is 1280 x 1024 / 65K colors. 3 Up to 35°C (95°F) when a dual processor configuration with E5-2667 v4, E5-2698 v4 or E5-2699 v4. 4 For Linux support, contact your sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html NEC Corporation Revision 1.0 – April, 2016 5 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h External Views Front View Legend A. Dump (NMI) Switch F. UID LED B. System Reset Switch G. UID LED Button C. System Status LED H. SUV Connector D. Power LED J. SSD Access Lamp #0 E. Power Button K. SSD Access Lamp #1 Configuration Diagram CHASSIS FRONT CHASSIS TOP 5 DIMM Slots Legend: Mandatory Components 5 DIMM Slots 1 DIMM Slot Processor #1 Processor #2 Drive Cage Option *Not support on N8400-252F/255F 4 DIMM Slots 4 DIMM Slots Type II Type I LAN Slot Standard Components NOTE: Solid State Drive Cage is not available in Xeon E5-2667 v3, Xeon E5-2697 v3 and Xeon E5-2699 v3 systems. NEC Corporation Revision 1.0 – April, 2016 6 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Expansion Slot #2 #1 #3 Legend #1 Type-I mezzanine card slot #2 Type-II mezzanine card slot #3 Flexible integrated NIC card slot NEC Corporation Revision 1.0 – April, 2016 7 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Server Configuration 1 Base Models Product Name / Description Part Number NEC Express5800 B120g-h (8C/E5-2620v4) N8400-250F no RAM, no SSD, no Network Controller Including: One Intel Xeon processor E5-2620 v4, EXPRESSBUILDER NEC Express5800 B120g-h (12C/E5-2650v4) no RAM, no SSD, no Network Controller Including: One Intel Xeon processor E5-2650 v4, EXPRESSBUILDER NEC Express5800 B120g-h (8C/E5-2667v4) no RAM, no Drive Cage, no Network Controller Including: One Intel Xeon processor E5-2667 v4, EXPRESSBUILDER NEC Express5800 B120g-h (14C/E5-2690v4) no RAM, no SSD, no Network Controller Including: One Intel Xeon processor E5-2690 v4, EXPRESSBUILDER NEC Express5800 B120g-h (20C/E5-2698v4) no RAM, no SSD, no Network Controller Including: One Intel Xeon processor E5-2698 v4, EXPRESSBUILDER NEC Express5800 B120g-h (22C/E5-2699v4) no RAM, no Drive Cage, no Network Controller Including: One Intel Xeon processor E5-2699 v4, EXPRESSBUILDER N8400-251F N8400-252F N8400-253F N8400-254F N8400-255F NOTE: The base model must be ordered with a memory kit and a network riser card kit. 2 2nd Processor Available sockets: 1 Product Name / Description Part Number Xeon E5-2620 v4 Processor Kit N8401-100F Intel® Xeon ® Processor E5-2620 v4 (2.10 GHz, 8C/16T, 20 MB) Xeon E5-2650 v4 Processor Kit N8401-101F Intel® Xeon ® Processor E5-2650 v4 (2.20 GHz, 12C/24T, 30 MB) Xeon E5-2667 v4 Processor Kit N8401-102F Intel® Xeon ® Processor E5-2667 v4 (3.20 GHz, 8C/16T, 25 MB) Xeon E5-2690 v4 Processor Kit N8401-103F Intel® Xeon ® Processor E5-2690 v4 (2.60 GHz, 14C/28T, 35 MB) Xeon E5-2698 v4 Processor Kit N8401-104F Intel® Xeon ® Processor E5-2698 v4 (2.20 GHz, 20C/40T, 50 MB) Xeon E5-2699 v4 Processor Kit N8401-105F Intel® Xeon ® Processor E5-2699 v4 (2.20 GHz, 22C/44T, 55 MB) NOTE: The 2nd processor must be the same as what is used in the base model NEC Corporation Revision 1.0 – April, 2016 8 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h The maximum number of logical processors supported by OS See the table below for the maximum number of logical processors that you can actually use on your system. Number of Logical Processors Supported by Operating Systems Maximum Available Number of logical Processors 1 Microsoft Windows Server 2012 R2 Standard Microsoft Windows Server 2012 R2 Datacenter 640 VMware ESXi 5.5 320 88 VMware ESXi 6.0 480 88 1 88 The maximum numbers of logical processors when using Hyper-V are below - Windows Server 2012 R2 : 320 3 Memory 3.1 Memory Configuration Available slots: 9 per processor Category Product Name / Description Part Number Registered DIMM (RDIMM) 4GB DDR4-2400 REG Memory Kit (1x4GB/R) N8402-170F 1 x 4 GB Registered ECC DIMM, DDR4-2400(PC4-19200) 8GB DDR4-2400 REG Memory Kit (1x8GB/R) N8402-171F 1 x 8 GB Registered ECC DIMM, DDR4-2400(PC4-19200) 16GB DDR4-2400 REG Memory Kit (1x16GB/R) N8402-172F 1 x 16 GB Registered ECC DIMM, DDR4-2400(PC4-19200) 32GB DDR4-2400 REG Memory Kit (1x32GB/R) N8402-173F 1 x 32 GB Registered ECC DIMM, DDR4-2400(PC4-19200) TSV-Registered DIMM (TSV-RDIMM) 64GB DDR4-2400 TSV REG Memory Kit (1x64GB/TSV-R) N8402-174F 1 x 64 GB TSV Registered ECC DIMM, DDR4-2400(PC4-19200) NOTE: Mix configurations of RDIMM and TSV RDIMM are not supported. Minimum one memory kit per processor must be installed into the system. It is recommended to install four identical memory kits for quad-channel symmetric memory configurations to increase memory transfer speed. At least 5 GB of memory is required for VMware ESXi 5.5 / 6.0. Maximum Memory Speed See the table below for the actual maximum memory transfer speed. The memory speed depends on the native memory bus speed of the memory controller. # of DIMMs per processor Processor Type Populated DIMMs N8400-250F(E5-2620v4) RDIMM (4, 8, 16, 32GB) TSV RDIMM (64GB) Up to 8 2133 MHz 9 1600 MHz RDIMM (4, 8, 16, 32GB) TSV RDIMM (64GB) Up to 4 2400 MHz 5-8 2133 MHz 9 1600 MHz N8400-251F(E5-2650v4) N8400-252F(E5-2667v4) N8400-253F(E5-2690v4) N8400-254F(E5-2698v4) N8400-255F(E5-2699v4) NEC Corporation Revision 1.0 – April, 2016 DIMM Speed 9 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Maximum Available Memory See the table below for the maximum memory size that you can actually use on your system. Maximum Memory Size Supported by Operating Systems 1 Microsoft Windows Server 2012 R2 Standard 1 Microsoft Windows Server 2012 R2 Datacenter 1 2 3 Maximum Available Memory 4 TB 1152 GB VMware ESXi 5.5 2 4 TB 1152 GB VMware ESXi 6.0 3 6 TB 1152 GB The maximum available memory size of Hyper-V systems are below: - Windows Server 2012 R2 : 4 TB Up to 1 TB of the main memory is available to each virtual machine. Up to 4 TB of the main memory is available to each virtual machine. 4 Internal Drives 4.1 Drive and RAID Configuration Refer to the section in accordance with your drive configuration. Available Interface Drive-less Two drives Refer to 4.2.1 None Non-RAID Refer to 4.2.2 SATA RAID 0/1 Refer to 4.2.3 SATA NOTE: Internal drives are not supported on a B120g-h with E5-2667v4 or E5-2699v4. RAID 0/1 is supported only on Windows operating systems. 4.2 Internal Drive Configuration 4.2.1 Drive-less 1 Category Product Name / Description Part Number Drive Cage 1 Required Drive-less Blade Kit Stiffener N8403-079F Not required for the B120g-h with E5-2667v4 or E5-2699v4, since those blades include a drive-less blade kit as standard. 4.2.2 Embedded SATA non-RAID Controller Category Product Name / Description Part Number Drive Cage Required SSD Drive Cage Kit Two 2.5-inch non-hot plug hard drive bays, one internal SATA cable 200GB Non-hot Plug 2.5-inch SATA SSD One 200 GB, 2.5-inch, eMLC, SATA ME(Middle Endurance) 400GB Non-hot Plug 2.5-inch SATA SSD One 400 GB, 2.5-inch, eMLC, SATA ME(Middle Endurance) N8403-080F Drive 2 slots available NEC Corporation SATA SSD Revision 1.0 – April, 2016 N8450-712 N8450-713 10 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h 200GB Non-hot Plug 2.5-inch SATA SSD One 200 GB, 2.5-inch, eMLC, SATA VE(Value Endurance) N8450-717 NOTE: Minimum one solid state drive must be installed. Solid State Drive Cage is not applicable for Xeon E5-2667 v4 or Xeon E5-2699 v4 systems. 4.2.3 Embedded SATA RAID Controller Category Product Name / Description Part Number Drive Cage Required SSD Drive Cage Kit Two 2.5-inch non-hot plug hard drive bays, one internal SATA cable 200GB Non-hot Plug 2.5-inch SATA SSD One 200 GB, 2.5-inch, eMLC, SATA ME(Middle Endurance) 400GB Non-hot Plug 2.5-inch SATA SSD One 400 GB, 2.5-inch, eMLC, SATA ME(Middle Endurance) 200GB Non-hot Plug 2.5-inch SATA SSD One 200 GB, 2.5-inch, eMLC, SATA VE(Value Endurance) N8403-080F Drive 2 slots available SATA SSD N8450-712 N8450-713 N8450-717 NOTE: All drives within a RAID array should be of the same capacity. RAID 0/1 is supported only on Windows operating systems. Solid State Drive Cage is not applicable for Xeon E5-2667 v4 or Xeon E5-2699 v4 systems. 5 I/O Expansion Card 5.1 Network Interface Controller Category Riser Required GbE 10GbE Adapter Type I GbE 10GbE Adapter Type II GbE Product Name / Description Part Number Dual Port 1GbE Riser Card Kit QLogic BCM57810 Dual Port 10GbE Riser Card Kit QLogic BCM57810 Dual Port 10GbE Riser Card Kit (iSCSI) QLogic BCM57810 Dual Port 1000BASE Adapter Intel® Ethernet Controller I350-AM2 Dual Port 10GbE Adapter QLogic BCM57810 Dual Port 10GbE Adapter (iSCSI) QLogic BCM57810 Quad Port 10GbE Adapter QLogic BCM57840 Quad Port 10GbE Adapter (iSCSI) QLogic BCM57840 Quad Port 1000BASE Adapter Intel® Ethernet Controller I350-AM4 N8403-094F N8403-095F N8403-096F N8403-076F N8403-097F N8403-098F N8403-099F N8403-100F N8403-077F NOTE: 8 GB of memory per one 10GbE network controller is recommended to avoid network performance issues. Only one 10GbE NIC can be installed when using with 32-bit operating systems. NEC Corporation Revision 1.0 – April, 2016 11 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h NIC Partitioning feature The 10GbE Controllers support NIC partitioning which is the ability to configure a single 10GbE port into two or four virtual NICs. To use NIC Partitioning, please note the following: NIC Partitioning should be enabled to install Windows Server operating systems. NIC Partitioning should be configured under the maximum configuration limits for networking when running with VMware systems. For more detail, see the Networking Maximum in the Configuration Maximums document for VMware. VMware system counts each divided network port as nx_nic 10Gb Ethernet port. For connections between virtual machines on the same server, configure the virtual machines on the same virtual switch or disable NIC Partitioning. An external switch may not loopback depending on its function or setting. For connections between controllers, confirm your network specifications in advance. NIC Teaming feature The Server blade supports NIC teaming which is the ability to configure multiple NICs to a single network interface for fault tolerance and load balancing. Windows Server 2012 R2 supports NIC teaming feature. When using NIC teaming, please note the following: Any of the network teaming must be processed in a single LAN controller. Teaming feature is not supported when iSCSI is used in network interface. iSCSI Offload Feature See the table below for the support matrix of NIC cards supporting iSCSI, available operating systems, and iSCSI offload feature. Type Part Number Operating Systems iSCSI Offload GbE N8403-094F Windows Server 2012 R2 / VMware Not available N8403-076F N8403-077F Windows Server 2012 R2 / VMware Not available N8403-095F Windows Server 2012 R2 / VMware Not available N8403-096F N8403-098F Windows Server 2012 R2 Available N8403-097F Windows Server 2012 R2 / VMware Not available N8403-099F Windows Server 2012 R2 / VMware Not available N8403-100F Windows Server 2012 R2 Available 10GbE NOTE: To configure iSCSI boot system, please contact your sales representative. NEC Corporation Revision 1.0 – April, 2016 12 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h 5.2 External Storage Controller 5.2.1 Fibre Channel Controller Category Product Name / Description Part Number Adapter Type I Fibre Channel Controller(8Gbps/2ch) Emulex LightPulse LPe1205-N Host Bus Adapter N8403-034F NOTE: Link speed of two ports in one card should be identical. 6 Other Add-in Components 6.1 Trusted Platform Module Kit Product Name / Description Part Number Trusted Platform Module Kit TPM 2.0 module N8415-010F NOTE: The kit is not available in China. The kit is not removable after attachment. "TPM Support" in BIOS setup menu must be activated prior to use of this product. To use Windows BitLocker drive encryption, be sure to keep the "recovery password" of BitLocker function. The recovery password is required to restore data for hardware replacement during a system error. NEC Corporation Revision 1.0 – April, 2016 13 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h References Boot Mode Setting The server supports Legacy mode and UEFI mode (default) as an OS Boot Mode. See the table below for the Boot Mode and X2APIC setting for each Operating System. As the default settings at the factory, UEFI mode is set as OS Boot mode and X2APIC is enabled. Refer to the User’s Guide and change the settings before installing an Operating System requiring Legacy Mode. Operating System Supported Boot Mode Supported X2APIC Setting Windows Server 2012 R2 UEFI Enabled VMware ESXi 5.5 Update 3 Legacy Disabled VMware ESXi 6.0 Update 1 Legacy Disabled NEC Corporation Revision 1.0 – April, 2016 14 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Server Management The EXPRESSSCOPE Engine 3, integrated into the server, provides superior remote control and system management features listed in the table below. Standard Temperature, voltage, power, drives, degeneration (memory, hard drive) Hardware event log collection Boot monitoring Booting, BIOS/POST stall, OS stall, shutdown Alerting HW error, Boot error and OS panic (by SNMP, E-Mail) Remote KVM POST/BIOS setup, DOS utility (via LAN) Panic screen, Boot screen Text-based screen (OS console) Hardware monitoring GUI-based screen (OS console) Remote control Remote reset/power on-off/ dump (via LAN) Power control BIOS and BMC Firmware update BIOS setting Others Industry standard 1 2 1 2 1 OS shutdown Remote media (CD/DVD, FD, USB Key) CLP (Command Line Protocol) (DMTF compliant) Remote control via Web browser (multi user login at the same time) Scheduling (without UPS) Set automatic IP address via DNS/DHCP LDAP/Active Directory verification/user control Clock synchronization of main unit and the RTC Access log collection IPMI 2.0 1 The feature is not supported on VMware ESXi systems. Some setting items can only be changed. NEC Corporation Revision 1.0 – April, 2016 15 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h OS Support Matrix for PCI Cards and Embedded Controllers ESXi 6.0 ESXi 5.5 WS 2012 R2 Part number Product Name N8403-094F Dual Port 1GbE Riser Card Kit N8403-095F Dual Port 10GbE Riser Card Kit N8403-096F Dual Port 10GbE Riser Card Kit (iSCSI) ‐ ‐ N8403-097F Dual Port 10GbE Adapter N8403-098F Dual Port 10GbE Adapter (iSCSI) ‐ ‐ N8403-099F Quad Port 10GbE Adapter N8403-100F Quad Port 10GbE Adapter (iSCSI) ‐ ‐ N8403-076F Dual Port 1000BASE Adapter N8403-077F Quad Port 1000BASE Adapter N8403-034F Fibre Channel Controller (8Gbps/2ch) NEC Corporation Revision 1.0 – April, 2016 16 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Support Matrix for Adapters and Network Interconnect Devices Network Adapter 10Gb Intelligent L3 Switch 10Gb Pass-Through Card N8406-052F 1Gb Pass-Through Card 10Gb Intelligent L3 Switch 1/10Gb Intelligent L3 Switch N8406-051F N8406-044 1Gb Intelligent L3 Switch N8406-035 N8406-036 N8406-011 N8406-029 N8460-023 N8460-023A N8403-094F Dual Port 1GbE Riser Card Kit N8403-095F Dual Port 10GbE Riser Card Kit N8403-096F Dual Port 10GbE Riser Card Kit N8403-097F Dual Port 10GbE Adapter N8403-098F Dual Port 10GbE Adapter N8403-099F Quad Port 10GbE Adapter - - - - - N8403-100F Quad Port 10GbE Adapter - - - - - N8403-077F 2 Product Name N8403-076F 1 Part Number Dual Port 1000BASE Adapter Quad Port 1000BASE Adapter 1 2 2 2 Existing 1Gb Intelligent L3 Switch installed for embedded NIC can be shared with embedded NIC and the optional NIC if N8406-013 1Gb Inter-link Expansion Card is installed in Blade Enclosure M system N8406-037 10GBASE-SR SFP+ module is not supported Fibre Channel Controller 8G FC switch 1 (24 ports) Fibre Channel Controller (8Gbps/2ch) N8406-042 N8403-034F 8G FC switch (12 ports) Product Name N8406-040 1 Part Number Supported for Blade Enclosure H v2 only NEC Corporation Revision 1.0 – April, 2016 17 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Supported PCI Cards and Installable Slots Part Number Product Name Slots Slot # : #1 #2 #3 Slot type: Type I Type II NIC N8403-094F Dual Port 1GbE Riser Card Kit - - N8403-095F Dual Port 10GbE Riser Card Kit - - N8403-096F Dual Port 10GbE Riser Card Kit - - N8403-097F Dual Port 10GbE Adapter - N8403-098F Dual Port 10GbE Adapter - N8403-099F Quad Port 10GbE Adapter - N8403-100F Quad Port 10GbE Adapter - N8403-076F Dual Port 1000BASE Adapter - N8403-077F Quad Port 1000BASE Adapter - - N8403-034F Fibre Channel Controller (8Gbps/2ch) - NEC Corporation Revision 1.0 – April, 2016 18 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Copyright Notice and Liability Disclaimer The information contained herein is subject to change without notice. Microsoft and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries Intel and Xeon are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Linux is a trademark of Linus Torvalds. Red Hat is a registered trademark of Red Hat, Inc. in the U.S. All other products, brands, or trade names used in this document are trademarks or registered trademarks of their respective holders. NEC shall not be liable for technical or editorial errors or omissions contained herein. For hard drive capacity measurements, 1 GB = 1 billion bytes. Actual formatted capacity is less. NEC Corporation Revision 1.0 – April, 2016 19 SYSTEM CONFIGURATION GUIDE – NEC Express5800/B120g-h Revision History Revision Date Description 1.0 April 25, 2016 Initial release NEC Corporation Revision 1.0 – April, 2016 20