FUJITSU SEMICONDUCTOR
DATA SHEET
DS704-00011-0v01-E
16-bit Proprietary Microcontroller
CMOS
2
F MC-16FX MB96690 Series
MB96F696*
DESCRIPTION
MB96690 series is based on FUJITSU’s advanced 16FX architecture (16-bit with instruction pipeline for
RISC-like performance). The CPU uses the same instruction set as the established 16LX series - thus
allowing for easy migration of 16LX Software to the new 16FX products.
16FX improvements compared to the previous generation include significantly improved performance even at the same operation frequency, reduced power consumption and faster start-up time.
For high processing speed at optimized power consumption an internal PLL can be selected to supply the
CPU with up to 32MHz operation frequency from an external 4MHz resonator. The result is a minimum
instruction cycle time of 31.2ns going together with excellent EMI behavior. The emitted power is
minimized by the on-chip voltage regulator that reduces the internal CPU voltage. A flexible clock tree
allows selecting suitable operation frequencies for peripheral resources independent of the CPU speed.
*: These devices are under development and specification is preliminary.
These products under development may change its specification without notice.
Note: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
For the information for microcontroller supports, see the following website.
http://edevice.fujitsu.com/micom/en-support/
Copyright©2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
2011.7
r2.0
MB96690 Series
FEATURES
z Technology
0.18μm CMOS
z CPU
2
F MC-16FX CPU
Optimized instruction set for controller applications
(bit, byte, word and long-word data types, 23 different addressing modes, barrel shift, variety of
pointers)
8-byte instruction execution queue
Signed multiply (16-bit × 16-bit) and divide (32-bit/16-bit) instructions available
z System clock
On-chip PLL clock multiplier (×1 to ×8, ×1 when PLL stop)
4 MHz to 8 MHz external crystal oscillator clock
(maximum frequency when using ceramic resonator depends on Q-factor)
Up to 16 MHz external clock for devices with fast clock input feature
32.768 kHz subsystem quartz clock
100kHz/2MHz internal RC clock for quick and safe startup, oscillator stop detection, watchdog
Clock source selectable from mainclock oscillator, subclock oscillator and on-chip RC oscillator,
independently for CPU and 2 clock domains of peripherals
The subclock oscillator is enabled by the Boot ROM program controlled by a configuration marker after
a Power or External reset
Low Power Consumption - 13 operating modes (different Run, Sleep, Timer modes, Stop mode)
z On-chip voltage regulator
Internal voltage regulator supports reduced internal MCU voltage, offering low EMI and low power
consumption figures
z Low voltage reset
Reset is generated when supply voltage is below minimum
z Code Security
Protects Flash Memory content from unintended read-out
z DMA
Automatic transfer function independent of CPU, can be assigned freely to resources
z Interrupts
Fast Interrupt processing
8 programmable priority levels
Non-Maskable Interrupt (NMI)
2
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
z CAN
Supports CAN protocol version 2.0 part A and B
ISO16845 certified
Bit rates up to 1 Mbit/s
32 message objects
Each message object has its own identifier mask
Programmable FIFO mode (concatenation of message objects)
Maskable interrupt
Disabled Automatic Retransmission mode for Time Triggered CAN applications
Programmable loop-back mode for self-test operation
z USART
Full duplex USARTs (SCI/LIN)
Wide range of baud rate settings using a dedicated reload timer
Special synchronous options for adapting to different synchronous serial protocols
LIN functionality working either as master or slave LIN device
Extended support for LIN-Protocol with 16-byte FIFO for selected channels to reduce interrupt load
z I2C
Up to 400 kbps
Master and Slave functionality, 7-bit and 10-bit addressing
z A/D converter
SAR-type
8/10-bit resolution
Signals interrupt on conversion end, single conversion mode, continuous conversion mode,
stop conversion mode, activation by software, external trigger, reload timers and PPGs
Range Comparator Function
Scan Disable Function
ADC Pulse Detection Function
z Source Clock Timers
Three independent clock timers (23-bit RC clock timer, 23-bit Main clock timer, 17-bit Sub clock timer)
z Hardware Watchdog Timer
Hardware watchdog timer is active after reset
Window function of Watchdog Timer is used to select the lower window limit of the watchdog interval
z Reload Timers
16-bit wide
1
2
3
4
5
6
Prescaler with 1/2 , 1/2 , 1/2 , 1/2 , 1/2 , 1/2 of peripheral clock frequency
Event count function
z Free Running Timers
Signals an interrupt on overflow
1
2
3
4
5
6
7
8
Prescaler with 1, 1/2 , 1/2 , 1/2 , 1/2 , 1/2 , 1/2 , 1/2 , 1/2 of peripheral clock frequency
z Input Capture Units
16-bit wide
Signals an interrupt upon external event
Rising edge, Falling edge or Both (rising&falling) edges sensitive
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
3
MB96690 Series
z Output Compare Units
16-bit wide
Signals an interrupt when a match with 16-bit I/O Timer occurs
A pair of compare registers can be used to generate an output signal
z Programmable Pulse Generator
16-bit down counter, cycle and duty setting registers
Can be used as 2 × 8-bit PPG
Interrupt at trigger, counter borrow and/or duty match
PWM operation and one-shot operation
Internal prescaler allows 1, 1/4, 1/16, 1/64 of peripheral clock as counter clock or of selected Reload
timer underflow as clock input
Can be triggered by software or reload timer
Can trigger ADC conversion
Timing point capture
Start delay
z Stepper Motor Controller
Stepper Motor Controller with integrated high current output drivers
Four high current outputs for each channel
Two synchronized 8/10-bit PWMs per channel
Internal prescaling for PWM clock: 1, 1/4, 1/5, 1/6, 1/8, 1/10, 1/12, 1/16 of peripheral clock
Dedicated power supply for high current output drivers
z LCD Controller
LCD controller with up to 4 COM × 36SEG
Internal or external voltage generation
Duty cycle: Selectable from options: 1/2, 1/3 and 1/4
Fixed 1/3 bias
Programmable frame period
Clock source selectable from four options (main clock, peripheral clock, subclock or RC oscillator
clock)
On-chip drivers for internal divider resistors or external divider resistors
On-chip data memory for display
LCD display can be operated in Timer Mode
Blank display: selectable
All SEG, COM and V pins can be switched between general and specialized purposes
z Sound Generator
8-bit PWM signal is mixed with tone frequency from 16-bit reload counter
PWM clock by internal prescaler: 1, 1/2, 1/4, 1/8 of peripheral clock
z Real Time Clock
Operational on main oscillation (4MHz), sub oscillation (32kHz) or RC oscillation (100kHz/2MHz)
Capable to correct oscillation deviation of Sub clock or RC oscillator clock (clock calibration)
Read/write accessible second/minute/hour registers
Can signal interrupts every half second/second/minute/hour/day
Internal clock divider and prescaler provide exact 1s clock
4
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
z External Interrupts
Edge or Level sensitive
Interrupt mask and pending bit per channel
Each available CAN channel RX has an external interrupt for wake-up
Selected USART channels SIN have an external interrupt for wake-up
z Non Maskable Interrupt
Disabled after reset, can be enabled by Boot-ROM depending on ROM configuration block
Once enabled, can not be disabled other than by reset
High or Low level sensitive
Pin shared with external interrupt 0
z I/O Ports
Most of the external pins can be used as general purpose I/O
2
All push-pull outputs (except when used as I C SDA/SCL line)
Bit-wise programmable as input/output or peripheral signal
Bit-wise programmable input enable
One input level per GP-IO-pin (either Automotive or CMOS-Schmitt trigger)
Bit-wise programmable pull-up resistor
z Built-in OCD (On Chip Debugger)
One-wire debug tool interface
Break function:
- Hardware break: 6 points (shared with code event)
- Software break: 4096 points
Event function
- Code event: 6 points (shared with hardware break)
- Data event: 6 points
- Event sequencer: 2 levels
Execution time measurement function
Trace function: 42 branches
Security function
z Flash Memory
Dual operation flash allowing reading of one Flash bank while programming or erasing the other bank
Command sequencer for automatic execution of programming algorithm and for supporting DMA for
programming of the Flash Memory
Supports automatic programming, Embedded Algorithm
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Erase can be performed on each sector individually
Sector protection
Flash Security feature to protect the content of the Flash
Low voltage detection during Flash erase
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
5
MB96690 Series
PRODUCT LINEUP
Features
Product type
Subclock
Dual Operation Flash memory
256.5KB + 32KB
MB96F69x
Remark
Flash product
Subclock can be set by software
RAM
16KB
MB96F696
LQFP-100
FPT-100P-M20
4ch
5ch
LIN-USART 0/1/2/4/5
2ch
LIN-USART 0/1
IC
1ch
10-bit A/D Converter
27ch
IC0
AN 2 to 4/6 to 8/10 to 12/
14 to 31
Package
DMA
USART
with automatic LIN-Header
transmisstion/reception
with 16 byte RX- and TX-FIFO
2
with Data Buffer
with Range Comparator
with Scan Disable
with ADC Pulse Detection
No
Yes
Yes
Yes
4ch
RLT 0/1/2/3/6
Only RLT6 can be used as
PPG clock source.
FRT 0/1
ICU 0/1/4/5/6/7
ICU 0/1/4/5/6 for
LIN-USART
OCU 0 to 3
10ch (16-bit) / 14ch (8-bit)
PPG 0 to 7/14/15
16-bit Reload Timer (RLT)
5ch
16-bit Free-Running Timer (FRT)
2ch
16-bit Input Capture Unit (ICU)
16-bit Output Compare Unit (OCU)
8/16-bit Programmable Pulse Generator
(PPG)
with Timing point capture
with Start delay
with Ramp
2
6ch
(5 channels for LIN-USART)
Yes
Yes
No
CAN Interface
1ch
Stepping Motor Controller (SMC)
External Interrupts (INTerrupt)
Non-Maskable Interrupt (NMI)
Sound generator (SG)
4ch
16ch
1ch
2ch
LCD Controller
Real Time Clock (RTC)
I/O Ports
Clock Calibration Unit (CAL)
Clock Output Function
4 COM × 36 SEG
CAN 0
32 Message Buffers
SMC 0/1/2/4
INT 0 to 15
SG 0/1
COM 0 to 3
SEG 0 to 4/7/11 to
28/30/33/36 to 45
1ch
77 (Dual clock mode)
79 (Single clock mode)
1ch
2ch
Low Voltage Reset
Yes
Hardware Watchdog Timer
On-chip RC-oscillator
On-chip Debugger
Yes
Yes
Yes
Low voltage reset can be
disabled by software
Notes: All signals of the peripheral function in each product cannot be allocated by limiting the pins of package.
It is necessary to use the port relocate function of the General I/O port according to your function use.
6
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
These devices are under development and specification is preliminary.
These products under development may change its specification without notice.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
7
MB96690 Series
BLOCK DIAGRAM
CKOT0_R, CKOT1, CKOT1_R
CKOTX0, CKOTX1, CKOTX1_R
X0, X1
X0A, X1A
RSTX
MD
NMI
DEBUG I/F
Clock &
Mode Controller
Flash
Memory A
Interrupt
Controller
16FX
CPU
OCD
16FX Core Bus (CLKB)
Peripheral
Bus Bridge
Watchdog
SDA0
SCL0
AVCC
AVSS
AVRH
AVRL
AN2 to AN4,
AN6 to AN8,
AN10 to AN12,
AN14 to AN31
Peripheral
Bus Bridge
Peripheral Bus 2 (CLKP2)
DMA
Controller
I2C
1 ch.
10-bit ADC
27 ch.
TIN0 to TIN3
TOT0 to TOT3
FRCK0
FRCK0_R
IN0
IN0_R, IN1_R
OUT0 to OUT3
OUT0_R, OUT2_R
FRCK1
IN6, IN7
IN4_R,IN5_R,IN7_R
16-bit
Reload Timer
4 ch.
I/O Timer 0
FRT0
ICU 0/1
OCU 0/1/2/3
Peripheral Bus 1 (CLKP1)
ADTG
I/O Timer 1
FRT1
ICU 4/5/6/7
V0 to V3
COM0 to COM3
SEG0 to SEG4, SEG7
SEG11 to SEG28,
SEG30, SEG33,
SEG36 to SEG45
LCD
Controller /
Driver
8
FUJITSU SEMICONDUCTOR CONFIDENTIAL
RAM
CAN Interface
1 ch.
Boot ROM
Voltage
Regulator
VCC
VSS
C
TX0
RX0
Sound
Generator
2 ch.
SGO0, SGO1, SGO1_R
SGA0, SGA1, SGA1_R
USART
5 ch.
SIN0 to SIN2, SIN4, SIN5, SIN5_R
SOT0 to SOT2, SOT4, SOT5_R
SCK0 to SCK2, SCK4, SCK5_R
PPG
10 ch. (16-bit) /
14 ch. (8-bit)
TTG0, TTG2 to TTG4, TTG6,TTG7,
TTG12 to TTG14
PPG0, PPG1, PPG3 to PPG7
PPG0_R to PPG4_R, PPG4_B to
PPG7_B, PPG14_B, PPG15_B
RLT6
Stepper
Motor
Controller
4 ch.
Real Time
Clock
External
Interrupt
PWM1M0 to PWM1M2, PWM1M4
PWM1P0 to PWM1P2, PWM1P4
PWM2M0 to PWM2M2, PWM2M4
PWM2P0 to PWM2P2, PWM2P4
DVCC
DVSS
WOT, WOT_R
INT0 to INT15
INT1_R to INT7_R
DS704-00011-0v01-E
MB96690 Series
PIN ASSIGNMENTS
Vss
Vss
DEBUG I/F
P17_0
MD
X0
X1
Vss
P04_0 / X0A*3
P04_1 / X1A*3
RSTX
P11_0 / COM0
P11_1 / COM1 / PPG0_R
P11_2 / COM2 / PPG1_R
P11_3 / COM3 / PPG2_R
P11_4 / SEG0 / PPG3_R
P11_5 / SEG1 / PPG4_R
P11_6 / SEG2 / FRCK0_R
P11_7 / SEG3 / IN0_R
P12_0 / SEG4 / IN1_R
P12_3 / SEG7 / OUT2_R
P12_7 / SEG11 / INT1_R
P00_0 / SEG12 / INT3_R
P00_1 / SEG13 / INT4_R
P00_2 / SEG14 / INT5_R
Vcc
(TOP VIEW)
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
50
76
Vcc
P00_3 / SEG15 / INT6_R
77
49
P10_3 / PWM2M4 / PPG7 / AN31
P00_4 / SEG16 / INT7_R
78
48
P10_2 / PWM2P4 / SCK2 / PPG6 / AN30*1
P00_5 / SEG17 / IN6 / TTG2 / TTG6
79
47
P10_1 / PWM1M4 /SOT2 / TOT3 / AN29
P00_6 / SEG18 / IN7 / TTG3 / TTG7
80
46
P10_0 / PWM1P4 / SIN2 / TIN3 / INT11 / AN28*1
P00_7 / SEG19 / SGO0 / INT14
81
45
DVss
P01_0 / SEG20 / SGA0
82
44
DVcc
P01_1 / SEG21 / CKOT1 / OUT0
83
43
P09_3 / PWM2M2 / AN27
P01_2 / SEG22 / CKOTX1 / OUT1 / INT15
84
42
P09_2 / PWM2P2 / AN26
P01_3 / SEG23 / PPG5
85
41
P09_1 / PWM1M2 / AN25
1
86
40
P09_0 / PWM1P2 / AN24
P01_5 / SEG25 / SOT4
87
39
P08_7 / PWM2M1 / AN23 /PPG7_B
1
88
38
P08_6 / PWM2P1 / AN22 /PPG6_B
P01_7 / SEG27 / CKOTX1_R / INT9 / TTG13
89
37
P08_5 / PWM1M1 / AN21
P02_0 / SEG28 / CKOT1_R / INT10 / TTG14
90
36
DVss
P02_2 / SEG30 / IN7_R / CKOT0_R / INT12
91
35
DVcc
P02_5 / SEG33 / OUT0_R / INT13 / SIN5_R*1
92
34
P08_4 / PWM1P1 / AN20
P03_0 / V0 / SEG36 / PPG4_B
93
33
P08_3 / PWM2M0 / AN19
P03_1 / V1 / SEG37 / PPG5_B
94
32
P08_2 / PWM2P0 / AN18
P03_2 / V2 / SEG38 / PPG14_B / SOT5_R
95
31
P08_1 / PWM1M0 / AN17
1
96
30
P08_0 / PWM1P0 / AN16
P03_4 / RX0 / INT4*1
97
29
P05_7 / AN15 / TOT2 / SGA1_R
P03_5 / TX0
98
28
P05_6 / AN14 / TIN2 / SGO1_R
P03_6 / INT0 / NMI
99
27
P05_4 / AN12 / INT2_R / WOT_R
Vss
Vcc
P05_3 / AN11 / OUT3 / SGA1
P05_2 / AN10 / OUT2 / SGO1
P05_0 / AN8
AVss
AVRL
AVRH
AVcc
P06_7 / AN7 / TOT1 / IN5_R
P06_6 / AN6 / TIN1 / IN4_R
P06_4 / AN4 / IN0 / TTG0 / TTG4
1
P06_3 / AN3 / FRCK0
P13_3 / PPG1 / TOT0 / WOT / SEG44
P06_2 / AN2 / INT5 / SIN5*1
P13_2 / PPG0 / TIN0 / FRCK1 / SEG43
P04_5 / PPG4 / SCL0*2
8
P04_4 / PPG3 / SDA0*2
7
P13_6 / SCK0 / CKOTX0*1
6
26
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
P13_5 / SOT0 / ADTG / INT7
5
P13_4 / SIN0 / INT6 / SEG45*
4
P13_1 / INT3 / SCK1 / SEG42*
3
1
100
1 2
Vss
Vcc
P13_0 / INT2 / SOT1 / SEG41
P03_3 / V3 / SEG39 / PPG15_B / SCK5_R*
P03_7 / INT1 / SIN1 / SEG40*1
P01_6 / SEG26 / SCK4 / TTG12*
LQFP - 100
C
P01_4 / SEG24 / SIN4 / INT8*
(FPT-100P-M20)
*1: CMOS input level only
2
*2: CMOS input level only for I C
*3: Please set Rom Configuration Block (RCB) to use the subclock
All other general-purpose pins have only Automotive input level.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
9
MB96690 Series
PIN FUNCTION DESCRIPTION
Pin name
Feature
Description
ADTG
ANn
AVcc
AVRH
AVRL
AVss
C
CKOTn
CKOTn_R
CKOTXn
CKOTXn_R
COMn
DVcc
DVss
FRCKn
FRCKn_R
INn
INn_R
INTn
INTn_R
MD
NMI
Pnn_m
OUTn
OUTn_R
PPGn
PPGn_R
PPGn_B
PWMn
RSTX
RXn
SCKn
SCKn_R
SCLn
SDAn
SEGn
SGAn
SGAn_R
SGOn
SGOn_R
SINn
SINn_R
SOTn
SOTn_R
ADC
ADC
Supply
ADC
ADC
Supply
Voltage regulator
Clock output function
Clock output function
Clock output function
Clock output function
LCD
Supply
Supply
Free Running Timer
Free Running Timer
ICU
ICU
External Interrupt
External Interrupt
Core
External Interrupt
GPIO
OCU
OCU
PPG
PPG
PPG
SMC
Core
CAN
USART
USART
2
IC
2
IC
LCD
Sound Generator
Sound Generator
Sound Generator
Sound Generator
USART
USART
USART
USART
A/D converter trigger input
A/D converter channel n input
Analog circuits power supply
A/D converter high reference voltage input
A/D converter low reference voltage input
Analog circuits power supply
Internally regulated power supply stabilization capacitor pin
Clock Output function n output
Relocated Clock Output function n output
Clock Output function n inverted output
Relocated Clock Output function n inverted output
LCD Common driver
SMC pins power supply
SMC pins power supply
Free Running Timer n input
Relocated Free Running Timer n input
Input Capture Unit n input
Relocated Input Capture Unit n input
External Interrupt n input
Relocated External Interrupt n input
Input pin for specifying the operating mode
Non-Maskable Interrupt input
General purpose I/O
Output Compare Unit n waveform output
Relocated Output Compare Unit n waveform output
Programmable Pulse Generator n output (16bit/8bit)
Relocated Programmable Pulse Generator n output (16bit/8bit)
Programmable Pulse Generator n output (8bit)
SMC PWM high current output
Reset input
CAN interface n RX input
USART n serial clock input/output
Relocated USART n serial clock input/output
2
I C interface n clock I/O input/output
2
I C interface n serial data I/O input/output
LCD Segment driver
SG amplitude output
Relocated SG amplitude output
SG sound/tone output
Relocated SG sound/tone output
USART n serial data input
Relocated USART n serial data input
USART n serial data output
Relocated USART n serial data output
10
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
Pin name
Feature
TINn
TOTn
TTGn
TXn
Vn
Vcc
Vss
WOT
WOT_R
X0
X0A
X1
X1A
DEBUG I/F
Reload Timer
Reload Timer
PPG
CAN
LCD
Supply
Supply
RTC
RTC
Clock
Clock
Clock
Clock
OCD
Description
Reload Timer n event input
Reload Timer n output
Programmable Pulse Generator n trigger input
CAN interface n TX output
LCD voltage reference
Power supply
Power supply
Real Time clock output
Relocated Real Time clock output
Oscillator input
Subclock Oscillator input
Oscillator output
Subclock Oscillator output
On Chip Debugger input/output
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
11
MB96690 Series
PIN CIRCUIT TYPE
Pin no.
I/O circuit type*
Pin name
1
Supply
Vss
2
F
C
3
P
P03_7 / INT1 / SIN1 / SEG40
4
J
P13_0 / INT2 / SOT1 / SEG41
5
P
P13_1 / INT3 / SCK1 / SEG42
6
J
P13_2 / PPG0 / TIN0 / FRCK1 / SEG43
7
J
P13_3 / PPG1 / TOT0 / WOT / SEG44
8
P
P13_4 / SIN0 / INT6 / SEG45
9
H
P13_5 / SOT0 / ADTG / INT7
10
M
P13_6 / SCK0 / CKOTX0
11
N
P04_4 / PPG3 / SDA0
12
N
P04_5 / PPG4 / SCL0
13
I
P06_2 / AN2 / INT5 / SIN5
14
K
P06_3 / AN3 / FRCK0
15
K
P06_4 / AN4 / IN0 / TTG0 / TTG4
16
K
P06_6 / AN6 / TIN1 / IN4_R
17
K
P06_7 / AN7 / TOT1 / IN5_R
18
Supply
AVcc
19
G
AVRH
20
G
AVRL
21
Supply
AVss
22
K
P05_0 / AN8
23
K
P05_2 / AN10 / OUT2 / SGO1
24
K
P05_3 / AN11 / OUT3 / SGA1
25
Supply
Vcc
26
Supply
Vss
27
K
P05_4 / AN12 / INT2_R / WOT_R
28
K
P05_6 / AN14 / TIN2 / SGO1_R
29
K
P05_7 / AN15 / TOT2 / SGA1_R
30
R
P08_0 / PWM1P0 / AN16
31
R
P08_1 / PWM1M0 / AN17
32
R
P08_2 / PWM2P0 / AN18
33
R
P08_3 / PWM2M0 / AN19
34
R
P08_4 / PWM1P1 / AN20
35
Supply
DVcc
12
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
Pin no.
I/O circuit type*
Pin name
36
Supply
DVss
37
R
P08_5 / PWM1M1 / AN21
38
R
P08_6 / PWM2P1 / AN22 / PPG6_B
39
R
P08_7 / PWM2M1 / AN23 / PPG7_B
40
R
P09_0 / PWM1P2 / AN24
41
R
P09_1 / PWM1M2 / AN25
42
R
P09_2 / PWM2P2 / AN26
43
R
P09_3 / PWM2M2 / AN27
44
Supply
DVcc
45
Supply
DVss
46
S
P10_0 / PWM1P4 / SIN2 / TIN3 / INT11 / AN28
47
R
P10_1 / PWM1M4 / SOT2 / TOT3 / AN29
48
S
P10_2 / PWM2P4 / SCK2 / PPG6 / AN30
49
R
P10_3 / PWM2M4 / PPG7 / AN31
50
Supply
Vcc
51
Supply
Vss
52
O
DEBUG I/F
53
H
P17_0
54
C
MD
55
A
X0
56
A
X1
57
Supply
Vss
58
B
P04_0 / X0A
59
B
P04_1 / X1A
60
C
RSTX
61
J
P11_0 / COM0
62
J
P11_1 / COM1 / PPG0_R
63
J
P11_2 / COM2 / PPG1_R
64
J
P11_3 / COM3 / PPG2_R
65
J
P11_4 / SEG0 / PPG3_R
66
J
P11_5 / SEG1 / PPG4_R
67
J
P11_6 / SEG2 / FRCK0_R
68
J
P11_7 / SEG3 / IN0_R
69
J
P12_0 / SEG4 / IN1_R
70
J
P12_3 / SEG7 / OUT2_R
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
13
MB96690 Series
Pin no.
I/O circuit type*
Pin name
71
J
P12_7 / SEG11 / INT1_R
72
J
P00_0 / SEG12 / INT3_R
73
J
P00_1 / SEG13 / INT4_R
74
J
P00_2 / SEG14 / INT5_R
75
Supply
Vcc
76
Supply
Vss
77
J
P00_3 / SEG15 / INT6_R
78
J
P00_4 / SEG16 / INT7_R
79
J
P00_5 / SEG17 / IN6 / TTG2 / TTG6
80
J
P00_6 / SEG18 / IN7 / TTG3 / TTG7
81
J
P00_7 / SEG19 / SGO0 / INT14
82
J
P01_0 / SEG20 / SGA0
83
J
P01_1 / SEG21 / CKOT1 / OUT0
84
J
P01_2 / SEG22 / CKOTX1 / OUT1 / INT15
85
J
P01_3 / SEG23 / PPG5
86
P
P01_4 / SEG24 / SIN4 / INT8
87
J
P01_5 / SEG25 / SOT4
88
P
P01_6 / SEG26 / SCK4 / TTG12
89
J
P01_7 / SEG27 / CKOTX1_R / INT9 / TTG13
90
J
P02_0 / SEG28 / CKOT1_R / INT10 / TTG14
91
J
P02_2 / SEG30 / IN7_R / CKOT0_R / INT12
92
P
P02_5 / SEG33 / OUT0_R / INT13 / SIN5_R
93
L
P03_0 / V0 / SEG36 / PPG4_B
94
L
P03_1 / V1 / SEG37 / PPG5_B
95
L
P03_2 / V2 / SEG38 / PPG14_B / SOT5_R
96
P
P03_3 / V3 / SEG39 / PPG15_B / SCK5_R
97
M
P03_4 / RX0 / INT4
98
H
P03_5 / TX0
99
H
P03_6 / INT0 / NMI
100
Supply
Vcc
*: Please refer to “
■ I/O CIRCUIT TYPE” for details on the I/O circuit types.
14
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
I/O CIRCUIT TYPE
Type
Circuit
Remarks
A
X1
R
0
1
FCI
X0
X out
High-speed oscillation circuit:
Programmable between
oscillation mode (external
crystal or resonator
connected to X0/X1 pins)
and Fast external Clock Input
(FCI) mode (external clock
connected to X0 pin)
Feedback resistor = approx.
1.0 MΩ. Feedback resistor is
grounded in the center when
the oscillator is disabled or in
FCI mode
The amplitude: 1.8V±0.15V
to operate by the internal
supply voltage
FCI or osc disable
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
15
MB96690 Series
Type
Circuit
Remarks
B
Pull-up control
P-ch
Standby
control
for input
shutdown
P-ch
N-ch
Pout
Nout
R
Low-speed oscillation circuit
shared with GPIO functionality:
Feedback resistor = approx.
5.0 MΩ. Feedback resistor is
grounded in the center when
the oscillator is disabled
GPIO functionality selectable
(CMOS hysteresis input with
input shutdown function,
IOL = 4mA, IOH = -4mA,
Programmable pull-up
resistor)
Hysteresis input
X1A
R
X out
0
1
FCI
X0A
FCI or Osc disable
Pull-up control
P-ch
Standby
control
for input
shutdown
P-ch
N-ch
Pout
Nout
R
Hysteresis input
C
CMOS hysteresis input pin
R
Hysteresis
inputs
16
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
Type
Circuit
Remarks
Power supply input
protection circuit
F
P-ch
N-ch
G
ANE
P-ch
AVR
N-ch
ANE
H
Pull-up control
P-ch
A/D converter ref+ (AVRH)
power supply input pin with
protection circuit
Without protection circuit
against VCC for pins AVRH
P-ch
N-ch
Pout
CMOS level output (IOL =
4mA, IOH = -4mA)
Automotive input with input
shutdown function
Programmable pull-up
resistor
Nout
R
Automotive input
Standby control
for input shutdown
I
Pull-up control
P-ch
P-ch
Pout
N-ch
Nout
R
CMOS level output (IOL =
4mA, IOH = -4mA)
CMOS hysteresis input with
input shutdown function
Programmable pull-up
resistor
Analog input
Hysteresis input
Standby control
for input shutdown
Analog input
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
17
MB96690 Series
Type
Circuit
Remarks
J
Pull-up control
P-ch
P-ch
Pout
N-ch
Nout
R
CMOS level output (IOL =
4mA, IOH = -4mA)
Automotive input with input
shutdown function
Programmable pull-up
resistor
SEG or COM output
Automotive input
Standby control
for input shutdown
SEG or COM output
K
Pull-up control
P-ch
P-ch
N-ch
Pout
CMOS level output (IOL =
4mA, IOH = -4mA)
Automotive input with input
shutdown function
Programmable pull-up
resistor
Analog input
Nout
R
Automotive input
Standby control
for input shutdown
Analog input
L
Pull-up control
P-ch
P-ch
Pout
N-ch
Nout
R
CMOS level output (IOL =
4mA, IOH = -4mA)
Automotive input with input
shutdown function
Programmable pull-up
resistor
Vx input or SEG output
Automotive input
Standby control
for input shutdown
Vx input or SEG output
18
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
Type
Circuit
Remarks
M
Pull-up control
P-ch
P-ch
N-ch
R
Pout
CMOS level output (IOL =
4mA, IOH = -4mA)
CMOS hysteresis input with
input shutdown function
Programmable pull-up
resistor
Nout
Hysteresis input
Standby control
for input shutdown
N
Pull-up control
P-ch
P-ch
N-ch
R
Pout
Nout*
CMOS level output (IOL =
3mA, IOH = -3mA)
CMOS hysteresis input with
input shutdown function
Programmable pull-up
resistor
*: N-channel transistor has slew
2
rate control according to I C
spec, irrespective of usage.
Hysteresis input
Standby control
for input shutdown
O
IOL: 25mA @ 2.7V
TTL input
N-ch
Nout
R
Standby control
for input shutdown
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
TTL input
19
MB96690 Series
Type
Circuit
Remarks
P
Pull-up control
P-ch
P-ch
N-ch
Pout
CMOS level output (IOL =
4mA, IOH = -4mA)
CMOS hysteresis inputs with
input shutdown function
Programmable pull-up
resistor
SEG or COM output
Nout
R
Hysteresis input
Standby control
for input shutdown
SEG or COM output
R
Pull-up control
P-ch
N-ch
P-ch
Pout
N-ch
Nout
CMOS level output
(programmable IOL = 4mA,
IOH = -4mA and IOL = 30mA,
IOH = -30mA)
Automotive input with input
shutdown function
Programmable pull-up /
pull-down resistor
Analog input
Pull-down control
R
Automotive input
Standby control
for input shutdown
Analog input
S
Pull-up control
P-ch
N-ch
P-ch
Pout
N-ch
Nout
CMOS level output
(programmable IOL = 4mA,
IOH = -4mA and IOL = 30mA,
IOH = -30mA)
CMOS hysteresis input with
input shutdown function
Programmable pull-up /
pull-down resistor
Analog input
Pull-down control
R
Hysteresis input
Standby control
for input shutdown
Analog input
20
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
MEMORY MAP
MB96F696
FF:FFFF H
USER ROM*
3
DE:0000 H
DD:FFFF H
Reserved
10:0000
H
0F:E000
H
0E:9000
H
Boot-ROM
Peripheral
Reserved
01:0000
H
00:8000
H
RAMSTART0* 2
ROM/RAM
MIRROR
Internal RAM
bank0
Reserved
00:0C00
H
00:0380
H
00:0180
H
GPR*1
00:0100
H
DMA
00:00F0
H
Reserved
00:0000
H
Peripheral
Peripheral
*1: For details about USER ROM area, see the “ USER ROM MEMORY MAP FOR FLASH
DEVICES” on the following pages.
*2: For RAMSTART/END addresses, please refer to the table on the next page.
*3: Unused GPR banks can be used as RAM area.
The DMA area is only available if the device contains the corresponding resource.
The available RAM and ROM area depends on the device.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
21
MB96690 Series
RAMSTART ADDRESSES
Devices
Bank 0
RAM size
RAMSTART0
MB96F696
16KByte
00:4200H
22
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
USER ROM MEMORY MAP FOR FLASH DEVICES
MB96F696
Alternative mode
CPU address
Flash memory
mode address
FF:FFFF H
FF:0000 H
FE:FFFF H
FE:0000 H
FD:FFFF H
FD:0000 H
FC:FFFF H
FC:0000 H
FB:FFFF H
3F:FFFF H
3F:0000 H
3E:FFFF H
3E:0000 H
3D:FFFF H
3D:0000 H
3C:FFFF H
3C:0000 H
3B:FFFF H
Flash size
256.5KB + 32KB
SA39 - 64KB
SA38 - 64KB
SA37 - 64KB
Bank A of Flash A
SA36 - 64KB
Reserved
DF:A000 H
DF:9FFF H
DF:8000 H
DF:7FFF H
DF:6000 H
DF:5FFF H
DF:4000 H
DF:3FFF H
DF:2000 H
DF:1FFF H
DF:0000 H
DE:FFFF H
DE:0000 H
1F:9FFF H
1F:8000 H
1F:7FFF H
1F:6000 H
1F:5FFF H
1F:4000 H
1F:3FFF H
1F:2000 H
1F:1FFF H
1F:0000 H
SA4 - 8KB
SA3 - 8KB
Bank B of Flash A
SA2 - 8KB
SA1 - 8KB
SAS - 512B*
Bank A of Flash A
Reserved
*: Phiysical address area of SAS-512B is from DF:0000H to DF:01FFH.
Others (from DF:0200H to DF:1FFFH) are all ROM Mirror area for SAS-512B.
Sector SAS contains the ROM configuration block RCBA at CPU address DF:0000H -DF:01FFH.
2
SAS can not be used for E PROM emulation.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
23
MB96690 Series
SERIAL PROGRAMMING COMMUNICATION INTERFACE
USART pins for Flash serial programming (MD = 0, DEBUG I/F = 0, Serial Communication mode)
MB96F696
Pin Number
USART Number
8
9
Normal Function
SIN0
USART0
SOT0
10
SCK0
3
SIN1
4
USART1
SOT1
5
SCK1
46
SIN2
47
USART2
SOT2
48
SCK2
86
SIN4
87
USART4
88
24
FUJITSU SEMICONDUCTOR CONFIDENTIAL
SOT4
SCK4
DS704-00011-0v01-E
MB96690 Series
INTERRUPT VECTOR TABLE
Vector
number
Offset in
vector table
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
3FC
3F8
3F4
3F0
3EC
3E8
3E4
3E0
3DC
3D8
3D4
3D0
3CC
3C8
3C4
3C0
3BC
3B8
3B4
3B0
3AC
3A8
3A4
3A0
39C
398
394
390
38C
388
384
380
37C
378
374
370
36C
368
364
360
35C
Vector name
Cleared by
DMA
Index in
ICR to
program
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
CALLV0
CALLV1
CALLV2
CALLV3
CALLV4
CALLV5
CALLV6
CALLV7
RESET
INT9
EXCEPTION
NMI
DLY
RC_TIMER
MC_TIMER
SC_TIMER
LVDI
EXTINT0
EXTINT1
EXTINT2
EXTINT3
EXTINT4
EXTINT5
EXTINT6
EXTINT7
EXTINT8
EXTINT9
EXTINT10
EXTINT11
EXTINT12
EXTINT13
EXTINT14
EXTINT15
CAN0
PPG0
PPG1
PPG2
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Description
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Non-Maskable Interrupt
Delayed Interrupt
RC clock timer
Main Clock Timer
Sub Clock Timer
Low Voltage Detector
External Interrupt 0
External Interrupt 1
External Interrupt 2
External Interrupt 3
External Interrupt 4
External Interrupt 5
External Interrupt 6
External Interrupt 7
External Interrupt 8
External Interrupt 9
External Interrupt 10
External Interrupt 11
External Interrupt 12
External Interrupt 13
External Interrupt 14
External Interrupt 15
CAN Controller 0
Reserved
Reserved
Reserved
Reserved
Programmable Pulse Generator 0
Programmable Pulse Generator 1
Programmable Pulse Generator 2
25
MB96690 Series
Vector
number
Offset in
vector table
Vector name
Cleared by
DMA
Index in
ICR to
program
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
358
354
350
34C
348
344
340
33C
338
334
330
32C
328
324
320
31C
318
314
310
30C
308
304
300
PPG3
PPG4
PPG5
PPG6
PPG7
PPG14
PPG15
RLT0
RLT1
RLT2
RLT3
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
2FC
PPGRLT
Yes
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
2F8
2F4
2F0
2EC
2E8
2E4
2E0
2DC
2D8
2D4
2D0
2CC
2C8
2C4
2C0
2BC
ICU0
ICU1
ICU4
ICU5
ICU6
ICU7
OCU0
OCU1
OCU2
OCU3
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
26
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Description
Programmable Pulse Generator 3
Programmable Pulse Generator 4
Programmable Pulse Generator 5
Programmable Pulse Generator 6
Programmable Pulse Generator 7
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Programmable Pulse Generator 14
Programmable Pulse Generator 15
Reserved
Reserved
Reserved
Reserved
Reload Timer 0
Reload Timer 1
Reload Timer 2
Reload Timer 3
Reserved
Reserved
Reload Timer 6 can be used as
PPG clock source
Input Capture Unit 0
Input Capture Unit 1
Reserved
Reserved
Input Capture Unit 4
Input Capture Unit 5
Input Capture Unit 6
Input Capture Unit 7
Reserved
Reserved
Reserved
Reserved
Output Compare Unit 0
Output Compare Unit 1
Output Compare Unit 2
Output Compare Unit 3
DS704-00011-0v01-E
MB96690 Series
Vector
number
Offset in
vector table
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
2B8
2B4
2B0
2AC
2A8
2A4
2A0
29C
298
294
290
28C
288
284
280
27C
278
274
270
26C
268
264
260
25C
258
254
250
24C
248
244
240
23C
238
234
230
22C
228
224
220
21C
Vector name
Cleared by
DMA
Index in
ICR to
program
FRT0
FRT1
RTC0
CAL0
SG0
IIC0
ADC0
LINR0
LINT0
LINR1
LINT1
LINR2
LINT2
LINR4
LINT4
LINR5
LINT5
-
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Description
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Free Running Timer 0
Free Running Timer 1
Reserved
Reserved
Real Time Clock
Clock Calibration Unit
Sound Generator 0
I2C interface0
Reserved
A/D Converter
Reserved
Reserved
LIN USART 0 RX
LIN USART 0 TX
LIN USART 1 RX
LIN USART 1 TX
LIN USART 2 RX
LIN USART 2 TX
Reserved
Reserved
LIN USART 4 RX
LIN USART 4 TX
LIN USART 5 RX
LIN USART 5 TX
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
27
MB96690 Series
Vector
number
Offset in
vector table
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
218
214
210
20C
208
204
Vector name
1F8
1F4
1F0
1EC
1E8
1E4
1E0
SG1
FLASHA
-
1DC
1D8
1D4
1D0
1CC
1C8
1C4
1C0
ADCRC0
ADCPD0
-
200
1FC
Cleared by
DMA
Index in
ICR to
program
Description
No
Yes
No
No
-
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Sound Generator 1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Flash memory A interrupt
Reserved
Reserved
Reserved
Reserved
Reserved
A/D Converter 0 - Range Comparator
A/D Converter 0 - Pulse detection
Reserved
Reserved
Reserved
28
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
HANDLING DEVICES
Special care is required for the following when handling the device:
• Latch-up prevention
• Unused pins handling
• External clock usage
• Notes on PLL clock mode operation
• Power supply pins (VCC/VSS)
• Crystal oscillator circuit
• Turn on sequence of power supply to A/D converter and analog inputs
• Pin handling when not using the A/D converter
• Notes on Power-on
• Stabilization of power supply voltage
• SMC power supply pins
• Serial communication
1. Latch-up prevention
CMOS IC chips may suffer latch-up under the following conditions:
• A voltage higher than VCC or lower than VSS is applied to an input or output pin.
• A voltage higher than the rated voltage is applied between VCC pins and VSS pins.
• The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current dramatically, causing thermal damages to the device.
For the same reason, extra care is required to not let the analog power-supply voltage (AVCC, AVRH) exceed
the digital power-supply voltage.
2. Unused pins handling
Unused input pins can be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. They must therefore be pulled up or pulled down through resistors. To prevent latch-up,
those resistors should be more than 2 kΩ.
Unused bidirectional pins can be set either to the output state and be then left open, or to the input state with
either input disabled or external pull-up/pull-down resistor as described above.
3. External clock usage
The permitted frequency range of an external clock depends on the oscillator type and configuration.
See AC Characteristics for detailed modes and frequency limits. Single and opposite phase external clocks must
be connected as follows:
1. Single phase external clock for Main oscillator
• When using a single phase external clock for the Main oscillator, X0 pin must be driven and X1 pin left
open. And supply 1.8V power to the external clock.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
29
MB96690 Series
2. Single phase external clock for Sub oscillator
• When using a single phase external clock for the Sub oscillator, ‘External clock mode’ must be selected and
X0A/GP04_0 must be driven. X1A/GP04_1 must be configured as GPIO.
4. Notes on PLL clock mode operation
If the PLL clock mode is selected and no external oscillator is operating or no external clock is supplied, the
microcontroller attempts to work with the free oscillating PLL. Performance of this operation, however, cannot
be guaranteed.
5. Power supply pins (VCC/VSS)
It is required that all VCC-level as well as all VSS-level power supply pins are at the same potential. If there is
more than one VCC or VSS level, the device may operate incorrectly or be damaged even within the guaranteed
operating range.
VCC and VSS must be connected to the device from the power supply with lowest possible impedance.
As a measure against power supply noise, it is required to connect a bypass capacitor of about 0.1 μF between
Vcc and Vss as close as possible to Vcc and Vss pins.
6. Crystal oscillator and ceramic resonator circuit
Noise at X0, X1 pins or X0A, X1A pins might cause abnormal operation. It is required to provide bypass
capacitors with shortest possible distance to X0, X1 pins and X0A, X1A pins, crystal oscillator (or ceramic
resonator) and ground lines, and, to the utmost effort, that the lines of oscillation circuit do not cross the lines of
other circuits.
It is highly recommended to provide a printed circuit board art work surrounding X0, X1 pins and X0A, X1A
pins with a ground area for stabilizing the operation.
It is highly recommended to evaluate the quartz/MCU or resonator/MCU system at the quartz or resonator
manufacturer, especially when using low-Q resonators at higher frequencies.
7. Turn on sequence of power supply to A/D converter and analog inputs
It is required to turn the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (ANn) on after
turning the digital power supply (VCC) on.
It is also required to turn the digital power off after turning the A/D converter supply and analog inputs off. In
this case, the voltage must not exceed AVRH or AVCC (turning the analog and digital power supplies
simultaneously on or off is acceptable).
8. Pin handling when not using the A/D converter
It is required to connect the unused pins of the A/D converter as AVCC = VCC, AVSS = AVRH = AVRL = VSS.
9. Notes on Power-on
To prevent malfunction of the internal voltage regulator, supply voltage profile while turning the power supply
on should be slower than 50μs from 0.2V to 2.7V.
10. Stabilization of power supply voltage
If the power supply voltage varies acutely even within the operation safety range of the Vcc power supply
voltage, a malfunction may occur. The Vcc power supply voltage must therefore be stabilized. As stabilization
guidelines, the power supply voltage must be stabilized in such a way that Vcc ripple fluctuations (peak to peak
value) in the commercial frequencies (50 Hz to 60 Hz) fall within 10% of the standard Vcc power supply voltage
and the transient fluctuation rate becomes 0.1V/μs or less in instantaneous fluctuation for power supply
switching.
30
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
11. SMC power supply pins
All DVCC /DVSS pins must be set to the same level as the VCC /VSS pins.
However note that the SMC I/O pin state is undefined if DVCC is powered on and VCC is below 3V. To avoid this,
we recommend to always power VCC before DVCC.
12. Serial communication
There is a possibility to receive wrong data due to noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example apply a checksum and retransmit
the data if an error occurs.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
31
MB96690 Series
ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
Parameter
Power supply
voltage*1
Analog power
supply voltage*1
Analog reference
voltage*1
SMC Power
supply*1
LCD power supply
voltage*1
Input voltage*1
Output voltage*1
Maximum Clamp
Current
Total Maximum
Clamp Current
"L" level maximum
output current
Condition
Vcc
-
Vss - 0.3
Vss + 6.0
V
AVcc
-
Vss - 0.3
Vss + 6.0
V
Vcc = AVcc*2
"L" level maximum
overall output
current
"L" level average
overall output
current
"H" level maximum
output current
"H" level maximum
overall output
current
"H" level average
overall output
current
Remarks
-
Vss - 0.3
Vss + 6.0
V
AVCC ≥ AVRH,
AVCC ≥ AVRL,
AVRH > AVRL,
AVRL ≥ AVSS
DVcc
-
Vss - 0.3
Vss + 6.0
V
Vcc = AVcc= DVcc*2
V0 to V3
-
Vss - 0.3
Vss + 6.0
V
VI
VO
-
Vss - 0.3
Vss - 0.3
Vss + 6.0
Vss + 6.0
V
V
ICLAMP
-
-4.0
+4.0
mA
Σ|ICLAMP|
-
-
25
mA
IOL
ΣIOL
TA=-40°C
TA=+25°C
TA=+85°C
TA=+105°C
TA=-40°C
TA=+25°C
TA=+85°C
TA=+105°C
-
-
15
52
39
32
30
4
40
30
25
23
50
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Normal outputs
ΣIOLSMC
-
-
260
mA
High current outputs
ΣIOLAV
-
-
25
mA
Normal outputs
ΣIOLSMCAV
-
-
170
mA
High current outputs
IOH
-
-15
-52
-39
-32
-30
-4
-40
-30
-25
-23
-50
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Normal outputs
ΣIOH
TA=-40°C
TA=+25°C
TA=+85°C
TA=+105°C
TA=-40°C
TA=+25°C
TA=+85°C
TA=+105°C
-
ΣIOHSMC
-
-
-260
mA
High current outputs
ΣIOHAV
-
-
-25
mA
Normal outputs
ΣIOHSMCAV
-
-
-170
mA
High current outputs
IOLSMC
IOLAVSMC
IOHSMC
IOHAV
"H" level average
output current
Unit
AVRH,
AVRL
IOLAV
"L" level average
output current
Rating
Min
Max
Symbol
IOHAVSMC
32
FUJITSU SEMICONDUCTOR CONFIDENTIAL
V0 to V3 must not
exceed Vcc
VI ≤ (D)VCC + 0.3V*3
VO ≤ (D)VCC + 0.3V*3
Applicable to general
purpose I/O pins *4
Applicable to general
purpose I/O pins *4
Normal outputs
High current outputs
Normal outputs
High current outputs
High current outputs
Normal outputs
High current outputs
Normal outputs
DS704-00011-0v01-E
MB96690 Series
Parameter
Symbol
Condition
Min
Rating
Max
Unit
Remarks
Power
PD
TA=+105°C
333 *6
mW
consumption*5
Operating ambient
TA
-40
105
°C
temperature
Storage temperature
TSTG
-55
150
°C
*1: This parameter is based on VSS = AVSS = DVSS = 0V.
*2: AVCC, DVCC and VCC must be set to the same voltage. It is required that AVCC does not exceed VCC and that
the voltage at the analog inputs does not exceed AVCC when the power is switched on.
*3: VI and VO should not exceed VCC + 0.3 V. VI should also not exceed the specified ratings. However if the
maximum current to/from an input is limited by some means with external components, the ICLAMP rating
supersedes the VI rating. Input/output voltages of standard ports depend on VCC.
*4: • Applicable to all general purpose I/O pins (Pnn_m).
• Use within recommended operating conditions.
• Use at DC voltage (current).
• The +B signal should always be applied a limiting resistance placed between the +B signal and the
microcontroller.
• The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
• Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may
affect other devices.
• Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0V), the power
supply is provided from the pins, so that incomplete operation may result.
• Note that if the +B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the Power reset (except devices with persistent low
voltage reset in internal vector mode).
• Sample recommended circuits:
Protective diode
VCC
P-ch
Limiting
resistance
+B input (0 V to 16 V)
N-ch
R
*5: The maximum permitted power dissipation depends on the ambient temperature, the air flow velocity and the
thermal conductance of the package on the PCB.
The actual power dissipation depends on the customer application and can be calculated as follows:
PD = PIO + PINT
PIO = Σ (VOL × IOL + VOH × IOH) (I/O load power dissipation, sum is performed on all I/O ports)
PINT = VCC × (ICC + IA) (internal power dissipation)
ICC is the total core current consumption into VCC as described in the “DC characteristics” and depends on the
selected operation mode and clock frequency and the usage of functions like Flash programming.
IA is the analog current consumption into AVCC.
*6: Worst case value for a package mounted on single layer PCB at specified TA without air flow.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
33
MB96690 Series
2. Recommended Operating Conditions
(VSS = AVSS = DVSS = 0V)
Parameter
Power supply
voltage
Smoothing
capacitor at C pin
Symbol
Vcc, DVcc
CS
Min
Value
Typ
Max
2.7
-
5.5
0.5
1.0
1.5
Unit
Remarks
V
μF
(Target value)
1.0µF (Allowance within ± 50%)
Please use the ceramic capacitor or the
capacitor of the frequency response of
this level.
The smoothing capacitor at VCC must
use the one of a capacity value that is
larger than Cs.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device's electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
34
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
3. DC Characteristics
1. Current rating of MB96F696 (Target value)
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Pin
name
Conditions
Vcc
PLL Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 32MHz
(CLKRC and CLKSC
stopped)
Main Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 4MHz
(CLKPLL, CLKSC and
CLKRC stopped)
Sub Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 32kHz
(CLKMC, CLKPLL and
CLKRC stopped)
PLL Sleep mode with
CLKS1/2 = CLKP1/2 =
32MHz
(CLKRC and CLKSC
stopped)
Main Sleep mode with
CLKS1/2 = CLKP1/2 =
4MHz
(CLKPLL, CLKRC and
CLKSC stopped)
Sub Sleep mode with
CLKS1/2 = CLKP1/2 =
32kHz,
(CLKMC, CLKPLL
and CLKRC stopped)
ICCPLL
Power supply
current in Run
modes*1
ICCMAIN
ICCSUB
ICCSPLL
Power supply
current in
Sleep modes*1
ICCSMAIN
ICCSSUB
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Min
Value
Typ
Max
-
28.5
-
mA
TA = +25°C
-
-
38
mA
TA = +105°C
-
5
-
mA
TA = +25°C
-
-
10
mA
TA = +105°C
-
0.5
-
mA
TA = +25°C
-
-
6
mA
TA = +105°C
-
10
-
mA
TA = +25°C
-
-
15
mA
TA = +105°C
-
3
-
mA
TA = +25°C
-
-
8
mA
TA = +105°C
-
0.3
-
mA
TA = +25°C
-
-
4.5
mA
TA = +105°C
Unit
Remarks
35
MB96690 Series
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
ICCTMAIN
Power supply
current in
Timer
modes*2
ICCTRCH
ICCTRCL
ICCTSUB
Power supply
current in
Stop mode*3
ICCH
Pin
name
Conditions
Main Timer mode
with
CLKMC = 4MHz
(CLKPLL, CLKRC
and CLKSC stopped)
RC Timer mode
with
CLKRC = 2MHz
RC Timer mode
with
CLKRC = 100kHz
Sub Timer mode
with
CLKSC = 32kHz
Vcc (CLKMC, CLKPLL
and CLKRC stopped)
Min
Value
Typ Max
Unit
Remarks
-
285
355
μA
TA = +25°C
-
-
1320
μA
TA = +105°C
-
160
245
μA
TA = +25°C
-
-
1230
μA
TA = +105°C
-
35
105
μA
TA = +25°C
-
-
1030
μA
TA = +105°C
-
25
90
μA
TA = +25°C
-
-
1000
μA
TA = +105°C
-
20
90
μA
TA = +25°C
-
-
1000
μA
TA = +105°C
-
Power supply
current
for active
Low voltage
5
15
μA
ICCLVD
Low
detector enabled
Voltage
detector*4
Flash Write/
Erase
12.5
20
mA
ICCFLASH
current*5
*1: The power supply current is measured with a 4MHz external clock connected to the Main oscillator and
a 32kHz external clock connected to the Sub oscillator. See chapter “Standby mode and voltage regulator
control circuit” of the Hardware Manual for further details about voltage regulator control. Power supply for
"On Chip Debugger" part is not included. Power supply current in Run mode does not include Flash Write /
Erase current.
*2: The power supply current in Timer mode is the value when Flash is in Power-down / reset mode.
The power supply current is measured with a 4MHz external clock connected to the Main oscillator and a
32kHz external clock connected to the Sub oscillator.
*3: The power supply current in Stop mode is the value when Flash is in Power-down / reset mode.
*4: When low voltage detector is enabled, ICCLVD must be added to Power supply current.
*5: When Flash Write / Erase program is executed, ICCFLASH must be added to Power supply current.
36
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
2. Pin characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter Symbol Pin name
VIH
"H" level
input
voltage
"L" level
input
voltage
External clock in
"oscillation mode"
External clock in
"oscillation mode"
VIHX0S
X0
VIHX0AS
X0A
VIHR
RSTX
-
VIHM
MD
-
VIHD
DEBUG I/F
-
VIL
Port inputs
Pnn_m
External clock in
"oscillation mode"
External clock in
"oscillation mode"
VILX0S
X0
VILX0AS
X0A
VILR
RSTX
-
VILM
MD
-
VILD
DEBUG I/F
-
VOH4
"H" level
output
voltage*
Port inputs
Pnn_m
Conditions
VOH30
VOH3
4mA type
High Drive
type
3mA type
4.5V ≤ Vcc ≤ 5.5V
IOH = -4mA
2.7V ≤ Vcc < 4.5V
IOH = -1.5mA
4.5V ≤ Vcc ≤ 5.5V
IOH = -52mA
2.7V ≤ Vcc < 4.5V
IOH = -18mA
4.5V ≤ Vcc ≤ 5.5V
IOH = -39mA
2.7V ≤ Vcc < 4.5V
IOH = -16mA
4.5V ≤ Vcc ≤ 5.5V
IOH = -32mA
2.7V ≤ Vcc < 4.5V
IOH = -14.5mA
4.5V ≤ Vcc ≤ 5.5V
IOH = -30mA
2.7V ≤ Vcc < 4.5V
IOH = -14mA
4.5V ≤ Vcc ≤ 5.5V
IOH = -3mA
2.7V ≤ Vcc < 4.5V
IOH = -1.5mA
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Min
VCC
× 0.7
VCC
× 0.8
VD
× 0.8
Vcc
× 0.8
Vcc
× 0.8
Vcc
- 0.3
2.0
Vss
- 0.3
Vss
- 0.3
Vss
Vss
- 0.3
Vss
- 0.3
Vss
- 0.3
Vss
- 0.3
(D)Vcc
- 0.5
Value
Typ Max
-
VCC
+ 0.3
VCC
+ 0.3
VD
Vcc
+ 0.3
Vcc
+ 0.3
Vcc
+ 0.3
Vcc
+ 0.3
VCC
× 0.3
VCC
× 0.5
VD
× 0.2
Vcc
× 0.2
VCC
× 0.2
Vss
+ 0.3
Unit
V
V
V
Remarks
CMOS
Hysteresis input
AUTOMOTIVE
Hysteresis input
VD=1.8V±0.15V
V
V
V
V
V
V
V
CMOS
Hysteresis input
CMOS
Hysteresis input
TTL Input
CMOS
Hysteresis input
AUTOMOTIVE
Hysteresis input
VD=1.8V±0.15V
V
V
V
-
0.8
V
-
(D)Vcc
V
CMOS
Hysteresis input
CMOS
Hysteresis input
TTL Input
TA = -40°C
TA = +25°C
DVcc
- 0.5
-
DVcc
V
TA = +85°C
TA = +105°C
Vcc
- 0.5
-
Vcc
V
37
MB96690 Series
Parameter Symbol Pin name
VOL4
"L" level
output
voltage*
VOL30
VOL3
Input leak
current
Total LCD
leak current
Internal
LCD divide
resistance
Pull-up
resistance
value
Pull-down
resistance
value
4mA type
High Drive
type
3mA type
Conditions
4.5V ≤ Vcc ≤ 5.5V
IOL = +4mA
2.7V ≤ Vcc < 4.5V
IOL = +1.7mA
4.5V ≤ Vcc ≤ 5.5V
IOL = +52mA
2.7V ≤ Vcc < 4.5V
IOL = +22mA
4.5V ≤ Vcc ≤ 5.5V
IOL = +39mA
2.7V ≤ Vcc < 4.5V
IOL = +18mA
4.5V ≤ Vcc ≤ 5.5V
IOL = +32mA
2.7V ≤ Vcc < 4.5V
IOL = +14mA
4.5V ≤ Vcc ≤ 5.5V
IOL = +30mA
2.7V ≤ Vcc < 4.5V
IOL = +13.5mA
2.7V ≤ Vcc < 5.5V
IOL = +3mA
Min
-
Value
Typ Max
-
0.4
Unit
V
TA = -40°C
TA = +25°C
-
-
0.5
V
TA = +85°C
TA = +105°C
-
-
0.4
V
Pnn_m
Vss < VI < Vcc
AVss, AVRL < VI
< AVcc, AVRH
-1
-
1
μA
P08_m,
P09_m,
P10_m
DVSS < VI < DVCC
AVSS, AVRL < VI
< AVCC, AVRH
-3
-
3
μA
IIL
Σ|IILCD|
All SEG/
COM pin
Vcc = 5.0V
-
0.5
10
μA
RLCD
Between
V3 and V2,
V2 and V1,
V1 and V0
Vcc = 5.0V
6.25
12.5
25
kΩ
RPU
Pnn_m
Vcc = 5.0V ±10%
25
50
100
kΩ
Vcc = 5.0V ±10%
25
50
100
kΩ
-
-
5
15
pF
-
-
15
30
pF
P08_m,
P09_m,
P10_m
Other than
Vcc, Vss,
AVcc,
AVss,
AVRH,
AVRL,
Input
CIN
P08_m,
capacitance
P09_m,
P10_m
P08_m,
P09_m,
P10_m
*: IOH and IOL are target value.
RDOWN
38
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Remarks
Single port pin
except high
current output
I/O for SMC
Maximum
leakage
current of all
LCD pins
DS704-00011-0v01-E
MB96690 Series
4. AC Characteristics
(1) Main Clock Input Characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VD=1.8V±0.15V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Input frequency
Input frequency
Symbol
fC
fFCI
Pin
name
Min
Value
Typ
Max
4
-
8
MHz
-
-
8
MHz
4
-
8
MHz
-
-
16
MHz
4
-
16
MHz
X0,
X1
Unit
X0
Input clock cycle
tCYLH
-
62.5
-
-
ns
Input clock pulse
width
PWH,
PWL
-
30
-
70
%
Remarks
When using a crystal
oscillator, PLL off
When using an opposite
phase external
clock, PLL off
When using a crystal
oscillator or opposite
phase external clock,
PLL on
When using a single
phase external
clock in “Fast Clock
Input mode”, PLL off
When using a single
phase external
clock in “Fast Clock
Input mode”, PLL on
tCYLH
Reference value:
1.8V±0.15V
The amplitude changes by resistance, capacity which added outside or the difference of the device.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
39
MB96690 Series
(2) Sub Clock Input Characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Min
Value
Typ
Max
-
-
32.768
-
kHz
-
-
-
100
kHz
X0A
-
-
-
50
kHz
Pin
Conditions
name
X0A,
X1A
Input frequency
FCL
Unit
Input clock cycle
tCYLL
-
-
10
-
-
μs
Input clock pulse
width
-
-
PWH/tCYLL
PWL/tCYLL
30
-
70
%
Remarks
When using an
oscillation circuit
When using an
opposite phase
external clock
When using a
single phase
external clock
tCYLL
0.8×Vcc
X0A
0.8×Vcc
0.8×Vcc
0.2×Vcc
PWH
0.2×Vcc
P WL
(3) Built-in RC Oscillation Characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Clock frequency
Symbol
Min
Value
Typ
Max
50
100
200
kHz
1
2
4
MHz
Unit
FRC
Remarks
When using slow frequency of
RC oscillator
When using fast frequency of
RC oscillator
(4) Internal Clock timing
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Value
Min
Max
Unit
Internal System clock frequency
(CLKS1 and CLKS2)
fCLKS1, fCLKS2
-
54
MHz
Internal CPU clock frequency (CLKB),
Internal peripheral clock frequency (CLKP1)
fCLKB, fCLKP1
-
32
MHz
Internal peripheral clock frequency (CLKP2)
fCLKP2
-
32
MHz
40
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
(5) Operating Conditions of PLL
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Value
Unit
Min Typ Max
PLL oscillation stabilization wait time
(LOCK UP time)
tLOCK
1
-
4
ms
PLL input clock frequency
PLL macro oscillation clock frequency
fPLLI
fPLLO
4
56
-
16
108
MHz
MHz
Remarks
Time from when the PLL
starts operating until the
oscillation stabilizes
(6) Reset Input Characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Reset input time
Rejection of reset input time
Symbol
Pin name
TRSTL
RSTX
Value
Unit
Min
Max
10
-
μs
1
-
μs
(7) Power-on Reset Timing
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Power on rise time
Power off time
Tr
Toff
Tr
Min
Value
Typ
Max
0.05
1
-
30
-
Unit
ms
ms
Toff
2.7V
0.2V
0.2V
0.2V
If the power supply is changed too rapidly, a power-on reset may occur.
We recommend a smooth startup by restraining voltages when changing the
power supply voltage during operation, as shown in the figure below.
2.7V
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
Rising edge of 50 mV/ms
maximum is allowed
41
MB96690 Series
(8) USART Timing
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Serial clock cycle time
4.5V ≤ Vcc < 5.5V
Pin
Conditions
Min
Max
name
tSCYC
SCKn
SCKn
tSLOVI
SOTn
SCKn Internal shift
tOVSHI
clock
SOTn
operation
SCKn
tIVSHI
SINn
SCKn
tSHIXI
SINn
SCK ↓ → SOT delay time
SOT → SCK ↑ delay time
SIN → SCK ↑ setup time
SCK ↑ → SIN hold time
Serial clock "L" pulse width
tSLSH
SCKn
Serial clock "H" pulse width
tSHSL
SCKn
2.7V ≤ Vcc < 4.5V
Min
Max
Unit
4 tCLKP1
-
4 tCLKP1
-
ns
- 20
+ 20
- 30
+ 30
ns
-
ns
-
ns
-
ns
-
ns
-
ns
N×tCLKP1
– 20*
tCLKP1
+ 45
0
tCLKP1
+ 10
tCLKP1
+ 10
-
N×tCLKP1
– 30*
tCLKP1
+ 55
0
tCLKP1
+ 10
tCLKP1
+ 10
SCKn
2 tCLKP1
2 tCLKP1
ns
External shift
SOTn
+ 45
+ 55
clock
SCKn
tCLKP1/2
tCLKP1/2
operation
ns
tIVSHE
SIN → SCK ↑ setup time
SINn
+ 10
+ 10
SCKn
tCLKP1
tCLKP1
tSHIXE
ns
SCK ↑ → SIN hold time
SINn
+ 10
+ 10
SCK fall time
tF
SCKn
ns
20
20
SCK rise time
tR
SCKn
ns
20
20
Notes: • The above characteristics apply to CLK synchronous mode.
• CL is the load capacity value of pins when testing.
• Depending on the used machine clock frequency, the maximum possible baud rate can be limited by
some parameters. These parameters are shown in “MB96690 series HARDWARE MANUAL”
• tCLKP1 indicates the peripheral clock 1 (CLKP1), Unit: ns
• These characteristics only guarantee the same relocate port number.
For example, the combination of SCLKn_0 and SOTn_1 is not guaranteed.
SCK ↓ → SOT delay time
tSLOVE
*: Parameter N depends on tSCYC and can be calculated as follows:
• If tSCYC = 2 × k × tCLKP1, then N = k, where k is an integer > 2
• If tSCYC = (2 × k + 1) × tCLKP1, then N = k + 1, where k is an integer > 1
Examples:
tSCYC
N
4 × tCLKP1
2
5 × tCLKP1, 6 × tCLKP1
3
7 × tCLKP1, 8 × tCLKP1
4
...
...
42
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
tSCYC
VOH
SCK
VOL
tSLOVI
VOH
SOT
VOL
tIVSHI
tSHIXI
VIH
VIH
VIL
VIL
SIN
MS bit = 0
tSHSL
tSLSH
SCK
VIH
VIH
VIL
VIL
tR
tF
SOT
tSLOVE
VOH
VOL
tIVSHE
SIN
tSHIXE
VIH
VIH
VIL
VIL
MS bit = 1
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
43
MB96690 Series
(9) External input timing
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Value
Min
Max
Pin name
Unit
Pnn_m
Remarks
General Purpose I/O
A/D converter trigger
input
ADTG
2tCLKP1 +200
FRCKn,
Free-Running Timer
(tCLKP1=
ns
FRCKn_R
tINH
1/fCLKP1)*
Input pulse width
TINn
Reload Timer
tINL
TTGn
PPG Trigger input
INn, INn_R
Input capture
INTn, INTn_R,
External interrupt
200
ns
NMI
NMI
*: tCLKP1 indicates the peripheral clock1 (CLKP1) cycle time except stop when in stop mode.
tINH
VILS
tINL
VILS
44
FUJITSU SEMICONDUCTOR CONFIDENTIAL
VIHS
VIHS
DS704-00011-0v01-E
MB96690 Series
2
(10) I C timing
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol
Conditions
Typical mode
Min
Max
High-speed
mode*4
Min
Max
Unit
SCL clock frequency
fSCL
0
100
0
400
kHz
(Repeated) START condition
hold time
tHDSTA
4.0
0.6
μs
SDA ↓ → SCL ↓
SCLclock "L" width
tLOW
4.7
1.3
μs
SCLclock "H" width
tHIGH
4.0
0.6
μs
(Repeated) START setup time
tSUSTA
4.7
0.6
μs
SCL ↑ → SDA ↓
CL = 50pF,
Data hold time
1
tHDDAT R = (Vp/IOL)*
0
3.45*2
0
0.9*3
μs
SCL ↓ → SDA ↓ ↑
Data setup time
tSUDAT
250
100
ns
SDA ↓ ↑ → SCL ↑
STOP condition setup time
tSUSTO
4.0
0.6
μs
SCL ↑ → SDA ↑
Bus free time between
"STOP condition" and
tBUS
4.7
1.3
μs
"START condition"
*1: R and C represent the pull-up resistance and load capacitance of the SCL and SDA lines, respectively. Vp
indicates the power supply voltage of the pull-up resistance and IOL indicates VOL guaranteed current.
*2: The maximum tHDDAT must satisfy that it doesn't extend at least "L" period (tLOW) of device's SCL signal.
*3: A high-speed mode I2C bus device can be used on a standard mode I2C bus system as long as the device
satisfies the requirement of "tSUDAT ≥ 250 ns".
*4: tCLKP1 is the peripheral clock1 (CLKP1) cycle time. To use I2C, set the peripheral bus clock at 6 MHz or
more.
SDA
tSUDAT
tLOW
tSUSTA
tBUS
SCL
tHDSTA
tHDDAT
tHIGH
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
tHDSTA
tSUSTO
45
MB96690 Series
z 10bit A/D Converter
Electrical characteristics for the A/D converter
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Symbol Pin name
Min
Value
Typ
Max
Unit
Resolution
-
-
-
-
10
bit
Total error
-
-
- 3.0
-
+ 3.0
LSB
Nonlinearity error
-
-
- 2.5
-
+ 2.5
LSB
-
-
- 1.9
-
+ 1.9
LSB
VOT
ANx
Typ - 20
Typ + 20
mV
VFST
ANx
Typ - 20
Typ + 20
mV
Compare time
-
-
Sampling time
-
-
5.0
8.0
3.1
μs
μs
μs
μs
mA
Differential
Nonlinearity error
Zero transition
voltage
Full transition
voltage
Power supply
current
Reference power
supply current
(between AVRH to
AVSS)
Analog input
capacity
Analog port input
current
Analog input
voltage
Reference voltage
range
IA
IAH
AVCC
IR
1.0
2.2
0.5
1.2
-
AVRL
+ 0.5LSB
AVRH
- 1.5LSB
2.0
-
-
3.3
μA
-
520
810
μA
A/D Converter active
-
-
1.0
μA
A/D Converter not
operated
-
-
16.0
pF
Normal outputs
-
-
17.8
pF
High current outputs
- 0.3
-
+ 0.3
μA
AVSS, AVRL < VAIN <
AVCC, AVRH
-3
-
+3
μA
AVRH
IRH
CVIN
IAIN
AN 2 to 4,
6 to 8,
10 to 12,
14, 15
AN 16 to 31
AN 2 to 4,
6 to 8,
10 to 12,
14, 15
AN 16 to 31
Remarks
VAIN
ANx
AVRL
-
AVRH
V
-
AVRH
AVCC
- 0.1
-
AVCC
V
-
AVRL
AVSS
-
AVSS
+ 0.1
V
46
FUJITSU SEMICONDUCTOR CONFIDENTIAL
4.5V ≤ ΑVCC ≤ 5.5V
2.7V ≤ ΑVCC < 4.5V
4.5V ≤ ΑVCC ≤ 5.5V
2.7V ≤ ΑVCC < 4.5V
A/D Converter active
A/D Converter not
operated
DS704-00011-0v01-E
MB96690 Series
Accuracy and setting of the A/D Converter sampling time
If the external impedance is too high or the sampling time too short, the analog voltage charged to the
internal sample and hold capacitor is insufficient, adversely affecting the A/D conversion precision.
To satisfy the A/D conversion precision, a sufficient sampling time must be selected. The required sampling
time depends on the external driving impedance Rext, the board capacitance of the A/D converter input pin
Cext and the AVcc voltage level. The following replacement model can be used for the calculation:
MCU
Rext
Analog
input
RVIN
Source
Comparetor
Cext
CVIN
Sampling switch
Rext: External driving impedance
Cext: Capacitance of PCB at A/D converter input
CVIN: Capacitance of MCU input pin (I/O, analog switch and ADC are contained)
16.0pF (Normal outputs), 17.8pF (High current outputs)
RVIN: Analog input impedance (I/O, analog switch and ADC are contained)
2050Ω (4.5V ≤ AVcc ≤ 5.5V), 3600Ω (2.7V ≤ AVcc < 4.5V)
The following approximation formula for the replacement model above can be used:
Tsamp [min] = 7.62 × (Rext × Cext + (Rext + RVIN) × CVIN)
Do not select a sampling time below the absolute minimum permitted value.
(0.5μs for 4.5V ≤ AVcc ≤ 5.5V, 1.2 μs for 2.7V ≤ AVcc < 4.5V)
If the sampling time cannot be sufficient, connect a capacitor of about 0.1 μF to the analog input pin.
A big external driving impedance also adversely affects the A/D conversion precision due to the pin
input leakage current IIL (static current before the sampling switch) or the analog input leakage current
IAIN (total leakage current of pin input and comparator during sampling). The effect of the pin input
leakage current IIL cannot be compensated by an external capacitor.
The accuracy gets worse as |AVRH - AVRL| becomes smaller.
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
47
MB96690 Series
• Definition of 10-bit A/D Converter Terms
Resolution
Linearity error
: Analog variation that is recognized by an A/D converter.
: Deviation of the line between the zero-transition point (0b0000000000←→
0b0000000001) and the full-scale transition point (0b1111111110 ←→
0b1111111111) from the actual conversion characteristics.
Differential linearity error : Deviation from the ideal value of the input voltage that is required to change the
output code by 1 LSB.
Total error
: Difference between the actual value and the theoretical value. The total error
includes zero transition error, full-scale transition error, and linearity error.
Linearity error
0x3FF
Actual conversion
characteristics
0x3FE
Actual conversion
characteristics
0x(N+1)
{1 LSB(N-1) + VOT}
VFST
VNT
0x004
(Actuallymeasured
value)
(Actually-measured
value)
0x003
Digital output
Digital output
0x3FD
Differential linearity error
Actual conversion
characteristics
Ideal characteristics
0x002
0x001
0xN
Ideal characteristics
(Actually-measured
value)
VNT
(Actually-measured
value)
0x(N-2)
VOT (Actually-measured value)
AVRL
V(N+1)T
0x(N-1)
Actual conversion characteristics
AVRH
AVRL
AVRH
Analog input
Linearity error of digital output N =
Analog input
VNT - {1LSB × (N - 1) + VOT}
1LSB’
Differential linearity error of digital output N =
1LSB =
N
VOT
VFST
VNT
:
:
:
:
V(N + 1) T - VNT
1LSB
[LSB]
- 1 [LSB]
VFST - VOT
1022
A/D converter digital output value.
Voltage at which the digital output changes from 0x000 to 0x001.
Voltage at which the digital output changes from 0x3FE to 0x3FF.
Voltage at which the digital output changes from 0x(N − 1) to 0xN.
48
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
Total error
0x3FF
1.5 LSB'
Digital output
0x3FE
Actual conversion
characteristics
0x3FD
{1 LSB'(N-1) + 0.5 LSB'}
0x004
VNT
0x003
(Actually-measured value)
Actual conversion
characteristics
Ideal characteristics
0x002
0x001
0.5 LSB'
AVRL
AVRH
Analog input
1LSB' (Ideal value) =
AVRH - AVRL
[V]
1024
Total error of digital output N =
VNT - {1LSB' × (N - 1) + 0.5LSB'}
1LSB'
N
: A/D converter digital output value.
VNT : Voltage at which the digital output changes from 0x(N + 1) to 0xN.
VOT' (Ideal value) = AVRL + 0.5LSB[V]
VFST' (Ideal value) = AVRH - 1.5LSB[V]
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
49
MB96690 Series
z High current output slew rate
(VCC = AVCC = 2.7V to 5.5V, DVCC = 4.5V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Rise time / Fall time
Symbol Pin name
P08_m,
P09_m,
P10_m
tR2,
tF2
Min
Value
Typ
Max
15
-
75
Voltage
Unit
Remarks
ns
CL=85pF
VH=VOL2+0.9 × (VOH30-VOL30)
VL=VOL2+0.1 × (VOH30-VOL30)
VH
VH
VL
VL
tR2
tF2
Time
z Low voltage detection characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Min
Value
Typ
Max
CILCR:LVL = 0000B
CILCR:LVL = 0001B
CILCR:LVL = 0010B
CILCR:LVL = 0011B
CILCR:LVL = 0100B
CILCR:LVL = 0111B
CILCR:LVL = 1001B
2.70
2.79
2.98
3.26
3.45
3.73
3.91
2.90
3.00
3.20
3.50
3.70
4.00
4.20
3.10
3.21
3.42
3.74
3.95
4.27
4.49
-
-0.004
-
-
Symbol
Conditions
Detected voltage
VDL0
VDL1
VDL2
VDL3
VDL4
VDL5
VDL6
Change ration of
power supply
voltage
dV/dt
Unit
Remarks
V
V
V
V
V
V
V
Detected voltage
V/μs (VDL) must be
within standards.
Voltage
Vcc
VDLx, max
VDLx, min
dV
dt
Time
50
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
z Flash Memory Write/Erase Characteristics
(VCC = AVCC = DVCC = 2.7V to 5.5V, VSS = AVSS = DVSS = 0V, TA = - 40°C to + 105°C)
Parameter
Sector erase
time
Large Sector
Min
Value
Typ
Max
-
0.6
Small Sector
Unit
Remarks
3.1
s
0.3
1.6
s
Excludes write time prior to internal
erase
Half word (16 bit) write time
-
25
400
μs
Chip erase time
-
2.7
14.2
s
Not including system-level overhead
time.
Excludes write time prior to internal
erase
Erase / write cycles and data hold time (targeted value)
Erase / write cycles
(cycle)
Data hold time
(year)
1,000
20 *
10,000
10 *
100,000
5*
*: This value comes from the technology qualification (using Arrhenius equation to translate high temperature
measurements into normalized value at + 85°C).
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
51
MB96690 Series
ORDERING INFORMATION
Part number
MB96F696RAPMC-GSE1*
MB96F696RAPMC-GSE2*
Flash memory
Package
Flash A
(288.5KB)
100-pin plastic LQFP
(FPT-100P-M20)
*: These devices are under development and specification is preliminary.
These products under development may change its specification without notice.
52
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
PACKAGE DIMENSION
100-pin plastic LQFP
Lead pitch
0.50 mm
Package width ×
package length
14.0 mm × 14.0 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.70 mm Max
Weight
0.65 g
Code
(Reference)
P-LFQFP100-14×14-0.50
(FPT-100P-M20)
100-pin plastic LQFP
(FPT-100P-M20)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
16.00±0.20(.630±.008)SQ
* 14.00±0.10(.551±.004)SQ
51
75
76
50
0.08(.003)
Details of "A" part
+0.20
26
100
1
25
C
0.20±0.05
(.008±.002)
0.08(.003) M
0.10±0.10
(.004 ±.004)
(Stand off)
0°~8°
"A"
0.50(.020)
+.008
1.50 –0.10 .059 –.004
(Mounting height)
INDEX
0.145±0.055
(.006±.002)
2005 -2010 FUJITSU SEMICONDUCTOR LIMITED F100031S-c-3-5
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
0.25(.010)
Dimensions in mm (inches).
Note: The values in parentheses are reference values
Please check the latest package dimension at the following URL.
http://edevice.fujitsu.com/package/en-search/
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
53
MB96690 Series
REVISION HISTORY
Revision
Date
Prelim 1
6-Ju1-2011
Modification
Creation
54
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E
MB96690 Series
DS704-00011-0v01-E
FUJITSU SEMICONDUCTOR CONFIDENTIAL
55
MB96690 Series
FUJITSU SEMICONDUCTOR LIMITED
Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome,
Kohoku-ku Yokohama Kanagawa 222-0033, Japan
Tel: +81-45-415-5858
http://jp.fujitsu.com/fsl/en/
For further information please contact:
North and South America
FUJITSU SEMICONDUCTOR AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600
Fax: +1-408-737-5999
http://us.fujitsu.com/micro/
Asia Pacific
FUJITSU SEMICONDUCTOR ASIA PTE. LTD.
151 Lorong Chuan,
#05-08 New Tech Park 556741 Singapore
Tel : +65-6281-0770 Fax : +65-6281-0220
http://sg.fujitsu.com/semiconductor/
Europe
FUJITSU SEMICONDUCTOR EUROPE GmbH
Pittlerstrasse 47, 63225 Langen, Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/semiconductor/
FUJITSU SEMICONDUCTOR SHANGHAI CO., LTD.
Rm. 3102, Bund Center, No.222 Yan An Road (E),
Shanghai 200002, China
Tel : +86-21-6146-3688 Fax : +86-21-6335-1605
http://cn.fujitsu.com/fss/
Korea
FUJITSU SEMICONDUCTOR KOREA LTD.
902 Kosmo Tower Building, 1002 Daechi-Dong,
Gangnam-Gu, Seoul 135-280, Republic of Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://kr.fujitsu.com/fsk/
FUJITSU SEMICONDUCTOR PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel : +852-2377-0226 Fax : +852-2376-3269
http://cn.fujitsu.com/fsp/
Specifications are subject to change without notice. For further information please contact each office.
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely
for the purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU
SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When
you develop equipment incorporating the device based on such information, you must assume any responsibility arising
out of such use of the information.
FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as
license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of
FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of
any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR
assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would
result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury,
severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use
requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or
damages arising in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the
regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited: Sales Promotion Department
56
FUJITSU SEMICONDUCTOR CONFIDENTIAL
DS704-00011-0v01-E