INTERSIL ISL6261A

NS
E SI G
D
W
E
RT
O R N EN T PA
F
D
CE M
NDE
M M E D R E P LA O
Data Sheet
C
RE
4C
DE
NOT OMMEN ISL6288
R EC
ISL6261A
®
Single-Phase Core Regulator for IMVP-6®
Mobile CPUs
The ISL6261A is a single-phase buck regulator
implementing lntel® IMVP-6® protocol, with embedded gate
drivers. lntel® Mobile Voltage Positioning (IMVP) is a smart
voltage regulation technology effectively reducing power
dissipation in lntel® Pentium processors.
The heart of the ISL6261A is the patented R3 Technology™,
Intersil’s Robust Ripple Regulator modulator. Compared with
the traditional multi-phase buck regulator, the R3
Technology™ has faster transient response. This is due to
the R3 modulator commanding variable switching frequency
during a load transient.
November 5, 2009
Features
• Precision single-phase CORE voltage regulator
- 0.5% system accuracy over temperature
- Enhanced load line accuracy
• Internal gate driver with 2A driving capability
• Microprocessor voltage identification input
- 7-Bit VID input
- 0.300V to 1.500V in 12.5mV steps
- Support VID change on-the-fly
• Multiple current sensing schemes supported
- Lossless inductor DCR current sensing
- Precision resistive current sensing
The ISL6261A provides three operation modes: the
Continuous Conduction Mode (CCM), the Diode Emulation
Mode (DEM) and the Enhanced Diode Emulation Mode
(EDEM). To boost battery life, the ISL6261A changes its
operation mode based on CPU mode signals DPRSLRVR
and DPRSTP#, and the FDE pin setting, to maximize the
efficiency. In CPU active mode, the ISL6261A commands
the CCM operation. When the CPU enters deeper sleep
mode, the ISL6261A enables the DEM to maximize the
efficiency at light load. Asserting the FDE pin of the
ISL6261A in CPU deeper sleep mode will enable the EDEM
to further decrease the switching frequency at light load and
increase the regulator efficiency.
• Thermal monitor
A 7-bit Digital-to-Analog Converter (DAC) allows dynamic
adjustment of the core output voltage from 0.300V to 1.500V.
The ISL6261A has 0.5% system voltage accuracy over
temperature.
ISL6261ACRZ
A unity-gain differential amplifier provides remote voltage
sensing at the CPU die. This allows the voltage on the CPU
die to be accurately measured and regulated per lntel®
IMVP-6 specification. Current sensing can be implemented
through either lossless inductor DCR sensing or precise
resistor sensing. If DCR sensing is used, an NTC thermistor
network will thermally compensates the gain and the time
constant variations caused by the inductor DCR change.
The ISL6261A provides the power monitor function through
the PMON pin. PMON output is a high-bandwidth analog
voltage signal representing the CPU instantaneous power.
The power monitor function can be used by the system to
optimize the overall power consumption, extending battery
run time.
1
FN6354.3
• Power monitor indicating CPU instantaneous power
• User programmable switching frequency
• Differential remote voltage sensing at CPU die
• Overvoltage, undervoltage, and overcurrent protection
• Pb-free (RoHS compliant)
Ordering Information
PART NUMBER
(Notes 2, 3)
PART
MARKING
TEMP.
RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL6261 ACRZ -10 to +100 40 Ld 6x6 QFN L40.6x6
ISL6261ACRZ-T* ISL6261 ACRZ -10 to +100 40 Ld 6x6 QFN L40.6x6
(Note 1)
Tape and Reel
ISL6261AIRZ
6261A IRZ
-40 to +100 40 Ld 6x6 QFN L40.6x6
ISL6261AIRZ-T* 6261A IRZ
(Note 1)
-40 to +100 40 Ld 6x6 QFN L40.6x6
Tape and Reel
NOTES:
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pbfree material sets, molding compounds/die attach materials, and
100% matte tin plate plus anneal (e3 termination finish, which is
RoHS compliant and compatible with both SnPb and Pb-free
soldering operations). Intersil Pb-free products are MSL classified at
Pb-free peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information
page for ISL6261A. For more information on MSL please see
techbrief TB363.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006, 2007, 2009. All Rights Reserved. R3 Technology™ is a trademark of Intersil Americas Inc.
All other trademarks mentioned are the property of their respective owners.
ISL6261A
Pinout
PGOOD
3V3
CLK_EN
DPRSTP#
DPRSLPVR
VR_ON
VID6
VID5
VID4
VID3
ISL6261A
(40 LD QFN)
TOP VIEW
40
39
38
37
36
35
34
33
32
31
FDE
1
30 VID2
PMON
2
29 VID1
RBIAS
3
28 VID0
VR_TT#
4
27 VCCP
NTC
5
SOFT
6
OCSET
7
24 PHASE
VW
8
23 UGATE
COMP
9
22 BOOT
FB
10
21 NC
2
26 LGATE
GND PAD
(BOTTOM)
11
12
13
14
15
16
17
18
19
20
VDIFF
VSEN
RTN
DROOP
DFB
VO
VSUM
VIN
VSS
VDD
25 VSSP
FN6354.3
November 5, 2009
ISL6261A
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +7V
Battery Voltage, VIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+28V
Boot Voltage (BOOT) . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +33V
Boot to Phase Voltage (BOOT-PHASE). . . . . . . . . -0.3V to +7V(DC)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to +9V(<10ns)
Phase Voltage (PHASE) . . . . . . . . . -7V (<20ns Pulse Width, 10µJ)
UGATE Voltage (UGATE) . . . . . . . . . . PHASE-0.3V (DC) to BOOT
. . . . . . . . . . . . . .PHASE-5V (<20ns Pulse Width, 10µJ) to BOOT
LGATE Voltage (LGATE) . . . . . . . . . . . . . . -0.3V (DC) to VDD+0.3V
. . . . . . . . . . . . . . . . -2.5V (<20ns Pulse Width, 5µJ) to VDD+0.3V
All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (VDD +0.3V)
Open Drain Outputs, PGOOD, VR_TT# . . . . . . . . . . . . -0.3 to +7V
Thermal Resistance (Typical, Notes 4, 5) θJA (°C/W)
θJC (°C/W)
QFN Package. . . . . . . . . . . . . . . . . . . .
33
6
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+5V ±5%
Battery Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V to 21V
Ambient Temperature
ISL6261ACRZ . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +100°C
ISL6261AIRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C
Junction Temperature
ISL6261ACRZ . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +125°C
ISL6261AIRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications
VDD = 5V, TA = -40°C to +100°C, unless otherwise specified. Boldface limits apply over the operating
temperature range, -40°C to +100°C.
MIN
(Note 7)
TYP
VR_ON = 3.3V
-
3.1
3.6
mA
VR_ON = 0V
-
-
1
µA
I3V3
No load on CLK_EN# pin
-
-
1
µA
Battery Supply Current at VIN Pin
IVIN
VR_ON = 0, VIN = 25V
-
-
1
µA
POR (Power-On Reset) Threshold
PORr
VDD rising
-
4.35
4.5
V
PORf
VDD falling
3.85
4.1
-
V
%Error
(Vcc_core)
ISL6261ACRZ
No load, close loop, active mode,
TA =-10°C to +100°C, VID = 0.75V to 1.5V
-0.5
-
0.5
%
-8
-
8
mV
VID = 0.3V to 0.4875V
-15
-
15
mV
%Error
(Vcc_core)
ISL6261AIRZ
No load, close loop, active mode,
VID = 0.75V to 1.5V
-0.8
-
0.8
%
PARAMETER
SYMBOL
TEST CONDITIONS
MAX
(Note 7) UNITS
INPUT POWER SUPPLY
+5V Supply Current
IVDD
+3.3V Supply Current
SYSTEM AND REFERENCES
System Accuracy
RBIAS Voltage
RRBIAS
Boot Voltage
VBOOT
VID = 0.5V to 0.7375V
VID = 0.5V to 0.7375V
-10
-
10
mV
VID = 0.3V to 0.4875V
-18
-
18
mV
RRBIAS = 147kΩ
1.45
1.47
1.49
V
1.188
1.2
1.212
V
Maximum Output Voltage
VCC_CORE
(max)
VID = [0000000]
-
1.5
-
V
Minimum Output Voltage
VCC_CORE
(min)
VID = [1100000]
-
0.3
-
V
VID = [1111111]
-
0.0
-
V
318
333
348
kHz
VID Off State
CHANNEL FREQUENCY
Nominal Channel Frequency
fSW
3
RFSET = 7kΩ, Vcomp = 2V
FN6354.3
November 5, 2009
ISL6261A
Electrical Specifications
VDD = 5V, TA = -40°C to +100°C, unless otherwise specified. (Continued) Boldface limits apply over the
operating temperature range, -40°C to +100°C. (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
Adjustment Range
MIN
(Note 7)
TYP
MAX
(Note 7) UNITS
200
-
500
kHz
-0.3
-
0.3
mV
-
90
-
dB
AMPLIFIERS
Droop Amplifier Offset
Error Amp DC Gain (Note 6)
AV0
Error Amp Gain-Bandwidth Product
(Note 6)
Error Amp Slew Rate (Note 6)
FB Input Current
GBW
CL = 20pF
-
18
-
MHz
SR
CL = 20pF
-
5.0
-
V/µs
-
10
150
nA
IIN(FB)
SOFT-START CURRENT
Soft-start Current
ISS
Soft Geyserville Current
IGV
|SOFT - REF|>100mV
Soft Deeper Sleep Entry Current
IC4
DPRSLPVR = 3.3V
Soft Deeper Sleep Exit Current
IC4EA
DPRSLPVR = 3.3V
36
41
46
µA
Soft Deeper Sleep Exit Current
IC4EB
DPRSLPVR = 0V
175
200
225
µA
-47
-42
-37
µA
±180
±205
±230
µA
-46
-41
-36
µA
POWER MONITOR
PMON Output Voltage Range
VPMON
VSEN = 1.2V, VDROOP - VO = 40mV
1.638
1.680
1.722
V
VSEN = 1V, VDROOP - VO = 10mV
0.308
0.350
0.392
V
PMON Maximum Voltage
VPMONMAX
2.8
3.0
-
V
PMON Sourcing Current
ISC_PMON
VSEN = 1V, VDROOP - VO = 25mV
2
-
-
mA
PMON Sinking Current
ISK_PMON
VSEN = 1V, VDROOP - VO = 25mV
2
-
-
mA
PMON
/130Ω
A
7
-
Ω
Maximum Current Sinking Capability
PMON Impedance
PMON/250Ω PMON/180Ω
ZPMON
When PMON current is within its
ourcing/sinking current range (Note 6)
-
GATE DRIVER DRIVING CAPABILITY (Note 6)
UGATE Source Resistance
RSRC(UGATE)
500mA source current
-
1
1.5
Ω
UGATE Source Current
ISRC(UGATE)
VUGATE_PHASE = 2.5V
-
2
-
A
UGATE Sink Resistance
RSNK(UGATE)
500mA sink current
-
1
1.5
Ω
UGATE Sink Current
ISNK(UGATE)
VUGATE_PHASE = 2.5V
-
2
-
A
LGATE Source Resistance
RSRC(LGATE)
500mA source current
-
1
1.5
Ω
LGATE Source Current
ISRC(LGATE)
VLGATE = 2.5V
-
2
-
A
LGATE Sink Resistance
RSNK(LGATE)
500mA sink current
-
0.5
0.9
Ω
LGATE Sink Current
ISNK(LGATE)
VLGATE = 2.5V
-
4
-
A
UGATE to PHASE Resistance
RP(UGATE)
-
1.1
-
kΩ
GATE DRIVER SWITCHING TIMING (Refer to “Gate Driver Timing Diagram” on page 6)
UGATE Turn-on Propagation Delay
LGATE Turn-on Propagation Delay
tPDHU
ISL6261ACRZ
TA = -10°C to +100°C,
PVCC = 5V, output unloaded
20
30
44
ns
tPDHU
ISL6261AIRZ
PVCC = 5V, output unloaded
18
30
44
ns
tPDHL
ISL6261ACRZ
TA = -10°C to +100°C,
PVCC = 5V, output unloaded
7
15
30
ns
tPDHL
ISL6261AIRZ
PVCC = 5V, output unloaded
5
15
30
ns
0.43
0.58
0.72
V
BOOTSTRAP DIODE
VDDP = 5V, forward bias current = 2mA
Forward Voltage
4
FN6354.3
November 5, 2009
ISL6261A
Electrical Specifications
VDD = 5V, TA = -40°C to +100°C, unless otherwise specified. (Continued) Boldface limits apply over the
operating temperature range, -40°C to +100°C. (Continued)
PARAMETER
SYMBOL
Leakage
TEST CONDITIONS
VR = 16V
MIN
(Note 7)
TYP
MAX
(Note 7) UNITS
-
-
1
μA
POWER GOOD and PROTECTION MONITOR
PGOOD Low Voltage
VOL
IPGOOD = 4mA
-
0.11
0.4
V
PGOOD Leakage Current
IOH
PGOOD = 3.3V
-1
-
1
µA
PGOOD Delay
tpgd
CLK_EN# low to PGOOD high
5.5
6.8
8.1
ms
Overvoltage Threshold
OVH
VO rising above setpoint > 1ms
155
195
235
mV
Severe Overvoltage Threshold
OVHS
VO rising above setpoint > 0.5µs
1.675
1.7
1.725
V
OCSET Reference Current
I(RBIAS) = 10µA
9.8
10
10.2
µA
OC Threshold Offset
DROOP rising above OCSET > 120µs
-3.5
-
3.5
mV
VO below set point for > 1ms
-360
-300
-240
mV
Undervoltage Threshold
(VDIFF-SOFT)
UVf
LOGIC THRESHOLDS
VR_ON and DPRSLPVR Input Low
VIL(3.3V)
-
-
1
V
VR_ON and DPRSLPVR Input High
VIH(3.3V)
2.3
-
-
V
-1
0
-
μA
Leakage Current on VR_ON
Leakage Current on DPRSLPVR
IIL
Logic input is low
IIH
Logic input is high
-
0
1
μA
IIL_DPRSLP
DPRSLPVR logic input is low
-1
0
-
μA
IIH_DPRSLP
DPRSLPVR logic input is high
-
0.45
1
μA
DAC(VID0-VID6), PSI# and
DPRSTP# Input Low
VIL(1.0V)
-
-
0.3
V
DAC(VID0-VID6), PSI# and
DPRSTP# Input High
VIH(1.0V)
0.7
-
-
V
Leakage Current of DAC(VID0-VID6)
and DPRSTP#
IIL
DPRSLPVR logic input is low
-1
0
-
μA
IIH
DPRSLPVR logic input is high
-
0.45
1
μA
THERMAL MONITOR
NTC Source Current
NTC = 1.3 V
Over-temperature Threshold
V(NTC) falling
VR_TT# Low Output Resistance
RTT
I = 20mA
CLK_EN# High Output Voltage
VOH
3V3 = 3.3V, I = -4mA
CLK_EN# Low Output Voltage
VOL
ICLK_EN# = 4mA
53
60
67
µA
1.17
1.2
1.25
V
-
5
9
Ω
2.9
3.1
-
V
-
0.18
0.4
V
CLK_EN# OUTPUT LEVELS
NOTES:
6. Limits established by characterization and are not production tested.
7. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
5
FN6354.3
November 5, 2009
ISL6261A
Gate Driver Timing Diagram
PWM
tPDHU
tFU
tRU
1V
UGATE
1V
LGATE
tRL
tFL
tPDHL
6
FN6354.3
November 5, 2009
ISL6261A
PGOOD
3V3
CLK_EN
DPRSTP#
DPRSLPVR
VR_ON
VID6
VID5
VID4
VID3
Functional Pin Description
40
39
38
37
36
35
34
33
32
31
FDE
1
30 VID2
PMON
2
29 VID1
RBIAS
3
28 VID0
VR_TT#
4
27 VCCP
NTC
5
SOFT
6
OCSET
7
24 PHASE
VW
8
23 UGATE
COMP
9
22 BOOT
FB
10
21 NC
26 LGATE
15
16
VSEN
RTN
DROOP
DFB
VO
17
18
19
20
VDD
14
VSS
13
VIN
12
25 VSSP
VSUM
11
VDIFF
GND PAD
(BOTTOM)
FDE
VW
Forced diode emulation enable signal. Logic high of FDE
with logic low of DPRSTP# forces the ISL6261A to operate
in diode emulation mode with an increased VW-COMP
voltage window.
A resistor from this pin to COMP programs the switching
frequency (eg. 6.81k = 300kHz).
PMON
Analog voltage output pin. The voltage potential on this pin
indicates the power delivered to the output.
COMP
The output of the error amplifier.
FB
The inverting input of the error amplifier.
RBIAS
VDIFF
A 147K resistor to VSS sets internal current reference.
The output of the differential amplifier.
VR_TT#
VSEN
Thermal overload output indicator with open-drain output.
Over-temperature pull-down resistance is 10.
Remote core voltage sense input.
NTC
Remote core voltage sense return.
Thermistor input to VR_TT# circuit and a 60µA current
source is connected internally to this pin.
DROOP
SOFT
A capacitor from this pin to GND pin sets the maximum slew
rate of the output voltage. The SOFT pin is the non-inverting
input of the error amplifier.
RTN
The output of the droop amplifier. DROOP-VO voltage is the
droop voltage.
DFB
The inverting input of the droop amplifier.
VO
OCSET
Overcurrent set input. A resistor from this pin to VO sets
DROOP voltage limit for OC trip. A 10µA current source is
connected internally to this pin.
7
An input to the IC that reports the local output voltage.
FN6354.3
November 5, 2009
ISL6261A
VSUM
VC24CP
This pin is connected to one terminal of the capacitor in the
current sensing R-C network.
5V power supply for the gate driver.
VIN
VID input with VID0 as the least significant bit (LSB) and
VID6 as the most significant bit (MSB).
Power stage input voltage. It is used for input voltage feed
forward to improve the input line transient performance.
VSS
VID0, VID1, VID2, VID3, VID4, VID5, VID6
VR_ON
Signal ground. Connect to controller local ground.
VR enable pin. A logic high signal on this pin enables the
regulator.
VDD
DPRSLPVR
5V control power supply.
Not connected. Ground this pin in the practical layout.
Deeper sleep enable signal. A logic high indicates that the
microprocessor is in Deeper Sleep Mode and also indicates
a slow Vo slew rate with 41μA discharging or charging the
SOFT cap.
BOOT
DPRSTP#
Upper gate driver supply voltage. An internal bootstrap diode
is connected to the VCCP pin.
UGATE
Deeper sleep slow wake up signal. A logic low signal on this
pin indicates that the microprocessor is in Deeper Sleep
Mode.
The upper-side MOSFET gate signal.
CLK_EN#
PHASE
Digital output for system PLL clock. Goes active 13 clock
cycles after Vcore is within 20mV of the boot voltage.
NC
The phase node. This pin should connect to the source of
upper MOSFET.
3V3
VSSP
3.3V supply voltage for CLK_EN#.
The return path of the lower gate driver.
PGOOD
LGATE
Power good open-drain output. Needs to be pulled up
externally by a 680 resistor to VCCP or 1.9k to 3.3V.
The lower-side MOSFET gate signal.
8
FN6354.3
November 5, 2009
Function Block Diagram
RBIAS
VR_ON
FDE
DPRSLPVR
DPRSTP#
CLK_EN#
PGOOD
3V3
VIN
VDD
VCCP
VID0
MODE CONTROL
VID1
VIN
PGOOD MONITOR AND LOGIC
VCCP
60µA
VID2
FLT
9
VID3
DAC
SOFT
PGOOD
FAULT AND PGOOD LOGIC
VID4
VID5
VO
1.22V
VID6
10µA
OCSET
VCCP
OC
VSUM
DROOP
VIN
VSOFT
FLT
DROOP
1
E/A
DRIVER
LOGIC
MODULATOR
VCCP
VO
1
Mupti-plier
VW
VO
VSEN
RTN
PMON
VDIFF
SOFT
FB
COMP
VW
VSS
FIGURE 1. SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM OF ISL6261A
ISL6261A
OC
DFB
FN6354.3
November 5, 2009
ISL6261A
Simplified Application Circuit for DCR Current Sensing
V
+5
V
+3.3
V
in
R4
C4
3V3
R5
VDD
VCCP
VIN
RBIAS
R6
C8
NTC
C5
UGATE
SOFT
VR_TT#
BOOT
L
C6
VR_TT#
o
V
o
PHASE
C
VIDs
VID<0:6>
o
DPRSTP#
DPRSTP#
DPRSLPVR
DPRSLPVR
LGATE
FDE
PMON
VSSP
PMON
CLK_ENABLE#
CLK_EN#
VR_ON
R8
VR_ON
IMVP6_PWRGD
VSUM
PGOOD
VCC-SENSE
C9
VSEN
VSS-SENSE
R7
RTN
R9
NTC
Network
VO
ISL6261A
C7
C3
R10
R11
VW
OCSET
C2
R2
C10
DFB
COMP
R12
FB
C1
R3
DROOP
VDIFF
R1
VSS
FIGURE 2. ISL6261A-BASED IMVP-6® SOLUTION WITH INDUCTOR DCR CURRENT SENSING
10
FN6354.3
November 5, 2009
ISL6261A
Simplified Application Circuit for Resistive Current Sensing
V
+5
V
+3.3
V
in
R4
C4
3V3
R5
VDD
VCCP
VIN
RBIAS
R6
C8
NTC
C5
UGATE
SOFT
VR_TT#
BOOT
L
C6
VR_TT#
o
R
sen
V
o
PHASE
VID<0:6>
C
VIDs
DPRSTP#
o
DPRSTP#
DPRSLPVR
DPRSLPVR
LGATE
FDE
PMON
VSSP
PMON
CLK_ENABLE#
CLK_EN#
VR_ON
R8
VR_ON
IMVP6_PWRGD
VSUM
PGOOD
VCC-SENSE
C9
VSEN
VSS-SENSE
R7
RTN
VO
ISL6261A
C7
C3
R10
R11
VW
OCSET
C2
R2
C10
DFB
COMP
R12
FB
C1
R3
DROOP
VDIFF
R1
VSS
FIGURE 3. ISL6261A-BASED IMVP-6® SOLUTION WITH RESISTIVE CURRENT SENSING
11
FN6354.3
November 5, 2009
ISL6261A
Theory of Operation
The ISL6261A is a single-phase regulator implementing
Intel® IMVP-6® protocol and includes an integrated gate
driver for reduced system cost and board area. The
ISL6261A IMVP-6® solution provides optimum steady state
and transient performance for microprocessor core voltage
regulation applications up to 25A. Implementation of Diode
Emulation Mode (DEM) operation further enhances system
efficiency.
The heart of the ISL6261A is the patented R3 Technology™,
Intersil’s Robust Ripple Regulator modulator. The R3™
modulator combines the best features of fixed frequency and
hysteretic PWM controllers while eliminating many of their
shortcomings. The ISL6261A modulator internally
synthesizes an analog of the inductor ripple current and
uses hysteretic comparators on those signals to establish
PWM pulses. Operating on the large-amplitude and noisefree synthesized signals allows the ISL6261A to achieve
lower output ripple and lower phase jitter than either
conventional hysteretic or fixed frequency PWM controllers.
Unlike conventional hysteretic converters, the ISL6261A has
an error amplifier that allows the controller to maintain 0.5%
voltage regulation accuracy throughout the VID range from
0.75V to 1.5V.
The hysteretic window voltage is with respect to the error
amplifier output. Therefore the load current transient results
in increased switching frequency, which gives the R3™
regulator a faster response than conventional fixed
frequency PWM regulators.
Start-up Timing
With the controller’s VDD pin voltage above the POR
threshold, the start-up sequence begins when VR_ON
exceeds the 3.3V logic HIGH threshold. In approximately
100μs, SOFT and VO start ramping to the boot voltage of
1.2V. At start-up, the regulator always operates in
Continuous Current Mode (CCM), regardless of the control
signals. During this interval, the SOFT cap is charged by a
41μA current source. If the SOFT capacitor is 20nF, the
SOFT ramp will be 2mV/µs for a soft-start time of 600µs.
Once VO is within 20mV of the boot voltage the ISL6261A
will count 13 clock cycles, then pull CLK_EN# low, and
charge/discharge the SOFT cap with approximately 200µA,
therefore VO slews at 10mV/µs to the voltage set by the VID
pins. In approximately 7ms, PGOOD is asserted HIGH.
Figure 4 shows typical start-up timing.
Static Operation
After the start-up sequence, the output voltage will be
regulated to the value set by the VID inputs per Table 1,
which is presented in the lntel® IMVP-6® specification. The
ISL6261A regulates the output voltage with ±0.5% accuracy
over the range of 0.7V to 1.5V.
12
VDD
10mV/µs
VR_ON
100µs
20mV
SOFT &VO
Vboot
13xTs
2mV/µs
CLK_EN#
~7ms
IMVP-VI PGOOD
FIGURE 4. SOFT-START WAVEFORMS USING A 20nF SOFT
CAPACITOR
A true differential amplifier remotely senses the core voltage
to precisely control the voltage at the microprocessor die.
VSEN and RTN pins are the inputs to the differential
amplifier.
As the load current increases from zero, the output voltage
droops from the VID value proportionally to achieve the
IMVP-6® load line. The ISL6261A can sense the inductor
current through the intrinsic series resistance of the
inductors, as shown in Figure 2, or through a precise resistor
in series with the inductor, as shown in Figure 3. The
inductor current information is fed to the VSUM pin, which is
the non-inverting input to the droop amplifier. The DROOP
pin is the output of the droop amplifier, and DROOP-VO
voltage is a high-bandwidth analog representation of the
inductor current. This voltage is used as an input to a
differential amplifier to achieve the IMVP-6® load line, and
also as the input to the overcurrent protection circuit.
The PMON pin is the power monitor output. The voltage
potential on this pin (VPMON) is given by VPMON = 35x(VSENVRTN)x(VDROOP-VO). Since VSEN-VRTN is the CPU voltage
and VDROOP-VO represents the inductor current, VPMON is
an analog voltage indicating the power consumed by the
CPU. VPMON has high bandwidth so it represents the
instantaneous power including the pulsation caused inductor
current switching ripple. The maximum available VPMON is
approximately 3V.
When using inductor DCR current sensing, an NTC
thermistor is used to compensate the positive temperature
coefficient of the copper winding resistance to maintain the
load-line accuracy.
The switching frequency of the ISL6261A controller is set by
the resistor RFSET between pins VW and COMP, as shown in
Figures 2 and 3.
FN6354.3
November 5, 2009
ISL6261A
TABLE 1. VID TABLE FROM INTEL IMVP-6 SPECIFICATION
TABLE 1. VID TABLE FROM INTEL IMVP-6 SPECIFICATION
(Continued)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VO (V)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VO (V)
0
0
0
0
0
0
0
1.5000
0
1
0
1
0
1
0
0.9750
0
0
0
0
0
0
1
1.4875
0
1
0
1
0
1
1
0.9625
1
0
1
1
0
0
0.9500
0
0
0
0
0
1
0
1.4750
0
0
0
0
0
0
1
1
1.4625
0
1
0
1
1
0
1
0.9375
0
0
0
0
1
0
0
1.4500
0
1
0
1
1
1
0
0.9250
0
0
0
0
1
0
1
1.4375
0
1
0
1
1
1
1
0.9125
1
1
0
0
0
0
0.9000
0
0
0
0
1
1
0
1.4250
0
0
0
0
0
1
1
1
1.4125
0
1
1
0
0
0
1
0.8875
0
0
0
1
0
0
0
1.4000
0
1
1
0
0
1
0
0.8750
0
0
0
1
0
0
1
1.3875
0
1
1
0
0
1
1
0.8625
1
1
0
1
0
0
0.8500
0
0
0
1
0
1
0
1.3750
0
0
0
0
1
0
1
1
1.3625
0
1
1
0
1
0
1
0.8375
0
0
0
1
1
0
0
1.3500
0
1
1
0
1
1
0
0.8250
0
0
0
1
1
0
1
1.3375
0
1
1
0
1
1
1
0.8125
1
1
1
0
0
0
0.8000
0
0
0
1
1
1
0
1.3250
0
0
0
0
1
1
1
1
1.3125
0
1
1
1
0
0
1
0.7875
0
0
1
0
0
0
0
1.3000
0
1
1
1
0
1
0
0.7750
0
0
1
0
0
0
1
1.2875
0
1
1
1
0
1
1
0.7625
1
1
1
1
0
0
0.7500
0
0
1
0
0
1
0
1.2750
0
0
0
1
0
0
1
1
1.2625
0
1
1
1
1
0
1
0.7375
0
0
1
0
1
0
0
1.2500
0
1
1
1
1
1
0
0.7250
0
0
1
0
1
0
1
1.2375
0
1
1
1
1
1
1
0.7125
0
0
0
0
0
0
0.7000
0
0
1
0
1
1
0
1.2250
1
0
0
1
0
1
1
1
1.2125
1
0
0
0
0
0
1
0.6875
0
0
1
1
0
0
0
1.2000
1
0
0
0
0
1
0
0.6750
0
0
1
1
0
0
1
1.1875
1
0
0
0
0
1
1
0.6625
0
0
0
1
0
0
0.6500
0
0
1
1
0
1
0
1.1750
1
0
0
1
1
0
1
1
1.1625
1
0
0
0
1
0
1
0.6375
0
0
1
1
1
0
0
1.1500
1
0
0
0
1
1
0
0.6250
0
0
1
1
1
0
1
1.1375
1
0
0
0
1
1
1
0.6125
0
0
1
0
0
0
0.6000
0
0
1
1
1
1
0
1.1250
1
0
0
1
1
1
1
1
1.1125
1
0
0
1
0
0
1
0.5875
0
1
0
0
0
0
0
1.1000
1
0
0
1
0
1
0
0.5750
0
1
0
0
0
0
1
1.0875
1
0
0
1
0
1
1
0.5625
0
0
1
1
0
0
0.5500
0
1
0
0
0
1
0
1.0750
1
0
1
0
0
0
1
1
1.0625
1
0
0
1
1
0
1
0.5375
0
1
0
0
1
0
0
1.0500
1
0
0
1
1
1
0
0.5250
0
1
0
0
1
0
1
1.0375
1
0
0
1
1
1
1
0.5125
0
1
0
0
0
0
0.5000
0
1
0
0
1
1
0
1.0250
1
0
1
0
0
1
1
1
1.0125
1
0
1
0
0
0
1
0.4875
0
1
0
1
0
0
0
1.0000
1
0
1
0
0
1
0
0.4750
0
1
0
1
0
0
1
0.9875
1
0
1
0
0
1
1
0.4625
13
FN6354.3
November 5, 2009
ISL6261A
TABLE 1. VID TABLE FROM INTEL IMVP-6 SPECIFICATION
(Continued)
TABLE 1. VID TABLE FROM INTEL IMVP-6 SPECIFICATION
(Continued)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VO (V)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VO (V)
1
0
1
0
1
0
0
0.4500
1
1
0
1
0
1
1
0.1625
1
0
1
0
1
0
1
0.4375
1
1
0
1
1
0
0
0.1500
1
0
1
0
1
1
0
0.4250
1
1
0
1
1
0
1
0.1375
1
0
1
0
1
1
1
0.4125
1
1
0
1
1
1
0
0.1250
1
0
1
1
0
0
0
0.4000
1
1
0
1
1
1
1
0.1125
1
0
1
1
0
0
1
0.3875
1
1
1
0
0
0
0
0.1000
1
0
1
1
0
1
0
0.3750
1
1
1
0
0
0
1
0.0875
1
0
1
1
0
1
1
0.3625
1
1
1
0
0
1
0
0.0750
1
0
1
1
1
0
0
0.3500
1
1
1
0
0
1
1
0.0625
1
0
1
1
1
0
1
0.3375
1
1
1
0
1
0
0
0.0500
1
0
1
1
1
1
0
0.3250
1
1
1
0
1
0
1
0.0375
1
0
1
1
1
1
1
0.3125
1
1
1
0
1
1
0
0.0250
1
1
0
0
0
0
0
0.3000
1
1
1
0
1
1
1
0.0125
1
1
0
0
0
0
1
0.2875
1
1
1
1
0
0
0
0.0000
1
1
0
0
0
1
0
0.2750
1
1
1
1
0
0
1
0.0000
1
1
0
0
0
1
1
0.2625
1
1
1
1
0
1
0
0.0000
1
1
0
0
1
0
0
0.2500
1
1
1
1
0
1
1
0.0000
1
1
0
0
1
0
1
0.2375
1
1
1
1
1
0
0
0.0000
1
1
0
0
1
1
0
0.2250
1
1
1
1
1
0
1
0.0000
1
1
0
0
1
1
1
0.2125
1
1
1
1
1
1
0
0.0000
1
1
0
1
0
0
0
0.2000
1
1
1
1
1
1
1
0.0000
1
1
0
1
0
0
1
0.1875
1
1
0
1
0
1
0
0.1750
TABLE 2. ISL6261A OPERATING CONFIGURATIONS
DPRSTP#
0
PHASE DETECTOR HISTORY
x
FDE
DPRSLPVR
OPERATIONAL MODE
VW-COMP VOLTAGE
WINDOW INCREASE
0
0
CCM
0%
1
DEM
<3 consecutive PWM with PHASE>0V
1
0
+20%
1
Three consecutive PWM with PHASE>0V
0
1
1
0
EDEM
+40%
CCM
0%
1
1
x
x
14
x
FN6354.3
November 5, 2009
ISL6261A
High Efficiency Operation Mode
The operational modes of the ISL6261A depend on the
control signal states of DPRSTP#, FDE, and DPRSLPVR, as
shown in Table 2. These control signals can be tied to lntel®
IMVP-6® control signals to maintain the optimal system
configuration for all IMVP-6® conditions.
DPRSTP# = 0, FDE = 0 and DPRSLPVR = 1 enables the
ISL6261A to operate in Diode Emulation Mode (DEM) by
monitoring the low-side FET current. In diode emulation
mode, when the low-side FET current flows from source to
drain, it turns on as a synchronous FET to reduce the
conduction loss. When the current reverses its direction, trying
to flow from drain to source, the ISL6261A turns off the
low-side FET to prevent the output capacitor from discharging
through the inductor, therefore eliminating the extra
conduction loss. When DEM is enabled, the regulator works in
automatic Discontinuous Conduction Mode (DCM), meaning
that the regulator operates in CCM in heavy load, and
operates in DCM in light load. DCM in light load decreases the
switching frequency to increase efficiency. This mode can be
used to support the deeper sleep mode of the microprocessor.
DPRSTP# = 0 and FDE = 1 enables the Enhanced Diode
Emulation Mode (EDEM), which increases the VW-COMP
window voltage by 33%. This further decreases the
switching frequency at light load to boost efficiency in the
deeper sleep mode.
based on load current. Light-load efficiency is increased in
both active mode and deeper sleep mode.
CPU mode-transition sequences often occur in concert with
VID changes. The ISL6261A employs carefully designed
mode-transition timing to work in concert with the VID changes.
The ISL6261A is equipped with internal counters to prevent
control signal glitches from triggering unintended mode
transitions. For example: Control signals lasting less than
seven switching periods will not enable the diode emulation
mode.
Dynamic Operation
The ISL6261A responds to VID changes by slewing to new
voltages with a dv/dt set by the SOFT capacitor and the logic of
DPRSLPVR. If CSOFT = 20nF and DPRSLPVR = 0, the output
voltage will move at a maximum dv/dt of ±10mV/μs for large
changes. The maximum dv/dt can be used to achieve fast
recovery from Deeper Sleep to Active mode. If CSOFT = 20nF
and DPRSLPVR = 1, the output voltage will move at a dv/dt of
±2mV/μs for large changes. The slow dv/dt into and out of
deeper sleep mode will minimize the audible noise. As the
output voltage approaches the VID command value, the dv/dt
moderates to prevent overshoot. The ISL6261A is IMVP-6®
compliant for DPRSTP# and DPRSLPVR logic.
Intersil R3™ has an intrinsic voltage feed forward function.
High-speed input voltage transients have little effect on the
output voltage.
For other combinations of DPRSTP#, FDE, and
DPRSLPVR, the ISL6261A operates in forced CCM.
The ISL6261A operational modes can be set according to
CPU mode signals to achieve the best performance. There
are two options: (1) Tie FDE to DPRSLPVR, and tie
DPRSTP# and DPRSLPVR to the corresponding CPU mode
signals. This configuration enables EDEM in deeper sleep
mode to increase efficiency. (2) Tie FDE to “1” and
DPRSTP# to “0” permanently, and tie DPRSLPVR to the
corresponding CPU mode signal. This configuration sets the
regulator in EDEM all the time. The regulator will enter DCM
Intersil R3™ commands variable switching frequency during
transients to achieve fast response. Upon load application,
the ISL6261A will transiently increase the switching
frequency to deliver energy to the output more quickly.
Compared with steady state operation, the PWM pulses
during load application are generated earlier, which
effectively increases the duty cycle and the response speed
of the regulator. Upon load release, the ISL6261A will
transiently decrease the switching frequency to effectively
reduce the duty cycle to achieve fast response.
TABLE 3. FAULT-PROTECTION SUMMARY OF ISL6261A
FAULT DURATION
PRIOR TO PROTECTION
FAULT TYPE
PROTECTION ACTIONS
FAULT RESET
Overcurrent fault
120µs
PWM tri-state, PGOOD latched low
VR_ON toggle or VDD toggle
Way-Overcurrent fault
<2µs
PWM tri-state, PGOOD latched low
VR_ON toggle or VDD toggle
Overvoltage fault (1.7V)
Immediately
Low-side FET on until Vcore < 0.85V, then
PWM tri-state, PGOOD latched low
(OV-1.7V always)
VDD toggle
Overvoltage fault (+200mV)
1ms
PWM tri-state, PGOOD latched low
VR_ON toggle or VDD toggle
Undervoltage fault (-300mV)
1ms
PWM tri-state, PGOOD latched low
VR_ON toggle or VDD toggle
VR_TT# goes high
N/A
Over-temperature fault (NTC<1.18) Immediately
15
FN6354.3
November 5, 2009
ISL6261A
Protection
The ISL6261A provides overcurrent (OC), overvoltage (OV),
undervoltage (UV) and over-temperature (OT) protections as
shown in Table 3.
Overcurrent is detected through the droop voltage, which is
designed as described in the “Component Selection and
Application” section. The OCSET resistor sets the
overcurrent protection level. An overcurrent fault will be
declared when the droop voltage exceeds the overcurrent
set point for more than 120µs. A way-overcurrent fault will be
declared in less than 2µs when the droop voltage exceeds
twice the overcurrent set point. In both cases, the UGATE
and LGATE outputs will be tri-stated and PGOOD will go low.
The overcurrent condition is detected through the droop
voltage. The droop voltage is equal to Icore × Rdroop, where
Rdroop is the load line slope. A 10μA current source flows out
of the OCSET pin and creates a voltage drop across ROCSET
(shown as R10 in Figure 2). Overcurrent is detected when
the droop voltage exceeds the voltage across ROCSET.
Equation 1 gives the selection of ROCSET.
ROCSET =
I OC × Rdroop
(EQ. 1)
10 μA
For example: The desired overcurrent trip level, Ioc, is 30A,
Rdroop is 2.1mΩ, Equation 1 gives ROCSET = 6.3k.
Undervoltage protection is independent of the overcurrent
limit. A UV fault is declared when the output voltage is lower
than (VID-300mV) for more than 1ms. The gate driver outputs
will be tri-stated and PGOOD will go low. Note that a practical
core regulator design usually trips OC before it trips UV.
There are two levels of overvoltage protection and response.
An OV fault is declared when the output voltage exceeds the
VID by +200mV for more than 1ms. The gate driver outputs
will be tri-stated and PGOOD will go low. The inductor
current will decay through the low-side FET body diode.
Toggling of VR_ON or bringing VDD below 4V will reset the
fault latch. A way-overvoltage (WOV) fault is declared
immediately when the output voltage exceeds 1.7V. The
ISL6261A will latch PGOOD low and turn on the low-side
FETs. The low-side FETs will remain on until the output
voltage drops below approximately 0.85V, then all the FETs
are turned off. If the output voltage again rises above 1.7V,
the protection process repeats. This mechanism provides
maximum protection against a shorted high-side FET while
preventing the output from ringing below ground. Toggling
VR_ON cannot reset the WOV protection; recycling VDD will
reset it. The WOV detector is active all the time, even when
other faults are declared, so the processor is still protected
against the high-side FET leakage while the FETs are
commanded off.
16
The ISL6261A has a thermal throttling feature. If the voltage
on the NTC pin goes below the 1.2V over-temperature
threshold, the VR_TT# pin is pulled low indicating the need
for thermal throttling to the system oversight processor. No
other action is taken within the ISL6261A.
Component Selection and Application
Soft-Start and Mode Change Slew Rates
The ISL6261A commands two different output voltage slew
rates for various modes of operation. The slow slew rate
reduces the inrush current during start-up and the audible noise
during the entry and the exit of Deeper Sleep Mode. The fast
slew rate enhances the system performance by achieving
active mode regulation quickly during the exit of Deeper Sleep
Mode. The SOFT current is bidirectional-charging the SOFT
capacitor when the output voltage is commanded to rise, and
discharging the SOFT capacitor when the output voltage is
commanded to fall.
Figure 5 shows the circuitry on the SOFT pin. The SOFT pin,
the non-inverting input of the error amplifier, is connected to
ground through capacitor CSOFT. ISS is an internal current
source connected to the SOFT pin to charge or discharge
CSOFT. The ISL6261A controls the output voltage slew rate
by connecting or disconnecting another internal current
source IZ to the SOFT pin, depending on the state of the
system, i.e. Start-up or Active mode, and the logic state on
the DPRSLPVR pin. The SOFT-START CURRENT section
of the Electrical Specification Table shows the specs of these
two current sources.
I
I
SS
Z
INTERNAL TO
ISL6261A
ERROR
AMPLIFLIER
C
V
SOFT
REF
FIGURE 5. SOFT PIN CURRENT SOURCES FOR FAST AND
SLOW SLEW RATES
ISS is 41µA typical and is used during start-up and mode
changes. When connected to the SOFT pin, IZ adds to ISS to
get a larger current, labeled IGV in the “Electrical
Specification Table” starting on page 3, on the SOFT pin. IGV
is typically 200µA with a minimum of 175µA.
FN6354.3
November 5, 2009
ISL6261A
10µA
R ocset
OCSET
I phase
OC
L
DCR
Vo
Rs
VSUM
C
o
DROOP
INTERNAL TO ISL6261A
series
DFB
R
ESR
0~10
par
R
R
1000pF
VSEN
opn1
R drp1
R
ntc
VO
Cn
1
R drp2
DROOP
VCC-SENSE
1000pF
1
TO PROCESSOR
SOCKET KELVIN
CONECTIONS
RTN
R
opn2
VSS-SENSE
330pF
VDIFF
FIGURE 6. SIMPLIFIED VOLTAGE DROOP CIRCUIT WITH CPU-DIE VOLTAGE SENSING AND INDUCTOR DCR CURRENT SENSING
The IMVP-6® specification reveals the critical timing
associated with regulating the output voltage. SLEWRATE,
given in the IMVP-6® specification, determines the choice of
the SOFT capacitor, CSOFT, through Equation 2:
CSOFT =
I GV
SLEWRATE
(EQ. 2)
If SLEWRATE is 10mV/μs, and IGV is typically 200μA, CSOFT
is calculated as:
C SOFT = 200 μA (10 mV μs ) = 20 nF
(EQ. 3)
Choosing 0.015μF will guarantee 10mV/μs SLEWRATE at
minimum IGV value. This choice of CSOFT controls the startup slew rate as well. One should expect the output voltage to
slew to the Boot value of 1.2V at a rate given by Equation 4:
dV soft
dt
=
I ss
C SOFT
=
41μA
= 2.8 mV
μs
0.015 μF
(EQ. 4)
Selecting Rbias
To properly bias the ISL6261A, a reference current needs to be
derived by connecting a 147k, 1% tolerance resistor from the
RBIAS pin to ground. This provides a very accurate 10μA
current source from which OCSET reference current is derived.
Caution should be used during layout. This resistor should
be placed in close proximity to the RBIAS pin and be
connected to good quality signal ground. Do not connect any
other components to this pin, as they will negatively impact
the performance. Capacitance on this pin may create
instabilities and should be avoided.
17
Start-up Operation - CLK_EN# and PGOOD
The ISL6261A provides a 3.3V logic output pin for
CLK_EN#. The system 3.3V voltage source connects to the
3V3 pin, which powers internal circuitry that is solely devoted
to the CLK_EN# function. The output is a CMOS signal with
4mA sourcing and sinking capability. CMOS logic eliminates
the need for an external pull-up resistor on this pin,
eliminating the loss on the pull-up resistor caused by
CLK_EN# being low in normal operation. This prolongs
battery run time. The 3.3V supply should be decoupled to
digital ground, not to analog ground, for noise immunity.
At start-up, CLK_EN# remains high until 13 clock cycles
after the core voltage is within 20mV of the boot voltage. The
ISL6261A triggers an internal timer for the IMVP6_PWRGD
signal (PGOOD pin). This timer allows PGOOD to go high
approximately 7ms after CLK_EN# goes low.
Static Mode of Operation - Processor Die Sensing
Remote sensing enables the ISL6261A to regulate the core
voltage at a remote sensing point, which compensates for
various resistive voltage drops in the power delivery path.
The VSEN and RTN pins of the ISL6261A are connected to
Kelvin sense leads at the die of the processor through the
processor socket. (The signal names are Vcc_sense and
Vss_sense respectively). Processor die sensing allows the
voltage regulator to tightly control the processor voltage at
the die, free of the inconsistencies and the voltage drops due
to layouts. The Kelvin sense technique provides for
extremely tight load line regulation at the processor die side.
FN6354.3
November 5, 2009
ISL6261A
These traces should be laid out as noise sensitive traces.
For optimum load line regulation performance, the traces
connecting these two pins to the Kelvin sense leads of the
processor should be laid out away from rapidly rising voltage
nodes (switching nodes) and other noisy traces. Common
mode and differential mode filters are recommended as
shown in Figure 6. The recommended filter resistance range
is 0~10Ω so it does not interact with the 50k input resistance
of the differential amplifier. The filter resistor may be inserted
between VCC-SENSE and the VSEN pin. Another option is
to place one between VCC-SENSE and the VSEN pin and
another between VSS-SENSE and the RTN pin. The need of
these filters also depends on the actual board layout and the
noise environment.
Since the voltage feedback is sensed at the processor die, if
the CPU is not installed, the regulator will drive the output
voltage all the way up to damage the output capacitors due
to lack of output voltage feedback. Ropn1 and Ropn2 are
recommended, as shown in Figure 6, to prevent this
potential issue. Ropn1 and Ropn2, typically ranging
20~100Ω, provide voltage feedback from the regulator local
output in the absence of the CPU.
Setting the Switching Frequency - FSET
The R3 modulator scheme is not a fixed frequency PWM
architecture. The switching frequency increases during the
application of a load to improve transient performance.
It also varies slightly depending on the input and output
voltages and output current, but this variation is normally
less than 10% in continuous conduction mode.
Resistor Rfset (R7 in Figure 2), connected between the VW
and COMP pins of the ISL6261A, sets the synthetic ripple
window voltage, and therefore sets the switching frequency.
This relationship between the resistance and the switching
frequency in CCM is approximately given by Equation 5.
R fset (kΩ ) = ( period(μs) − 0.29) × 2.33
(EQ. 5)
In diode emulation mode, the ISL6261A stretches the
switching period. The switching frequency decreases as the
load becomes lighter. Diode emulation mode reduces the
switching loss at light load, which is important in conserving
battery power.
Voltage Regulator Thermal Throttling
lntel® IMVP-6® technology supports thermal throttling of the
processor to prevent catastrophic thermal damage to the
voltage regulator. The ISL6261A features a thermal monitor
sensing the voltage across an externally placed negative
temperature coefficient (NTC) thermistor. Proper selection
and placement of the NTC thermistor allows for detection of
a designated temperature rise by the system.
18
54µA
NTC
V
NTC
R
6µA
Internal to
ISL6261A
VR_TT#
SW1
NTC
SW2
R
S
1.23V
1.20V
FIGURE 7. CIRCUITRY ASSOCIATED WITH THE THERMAL
THROTTLING FEATURE
Figure 7 shows the circuitry associated with the thermal
throttling feature of the ISL6261A. At low temperature, SW1
is on and SW2 connects to the 1.20V side. The total current
going into the NTC pin is 60µA. The voltage on the NTC pin
is higher than 1.20V threshold voltage and the comparator
output is low. VR_TT# is pulled up high by an external
resistor. Temperature increase will decrease the NTC
thermistor resistance. This decreases the NTC pin voltage.
When the NTC pin voltage drops below 1.2V, the comparator
output goes high to pull VR_TT# low, signaling a thermal
throttle. In addition, SW1 turns off and SW2 connects to
1.23V, which decreases the NTC pin current by 6uA and
increases the threshold voltage by 30mV. The VR_TT#
signal can be used by the system to change the CPU
operation and decrease the power consumption. As the
temperature drops, the NTC pin voltage goes up. If the NTC
pin voltage exceeds 1.23V, VR_TT# will be pulled high.
Figure 8 illustrates the temperature hysteresis feature of
VR_TT#. T1 and T2 (T1>T2) are two threshold temperatures.
VR_TT# goes low when the temperature is higher than T1
and goes high when the temperature is lower than T2.
VR_TT#
Logic_1
Logic_0
T2
T1
T (oC)
FIGURE 8. VR_TT# TEMPERATURE HYSTERISIS
FN6354.3
November 5, 2009
ISL6261A
The NTC thermistor’s resistance is approximately given by
the following formula:
R
NTC
(T ) = R
NTCTo
1
1
b⋅(
−
)
T
273
To
273
+
+
⋅e
(EQ. 6)
T is the temperature of the NTC thermistor and b is a
constant determined by the thermistor material. To is the
reference temperature at which the approximation is
derived. The most commonly used To is +25°C. For most
commercial NTC thermistors, there is b = 2750k, 2600k,
4500k or 4250k.
From the operation principle of VR_TT#, the NTC resistor
satisfies the following equation group:
R NTC (T1 ) + Rs =
1.20V
= 20kΩ
60 μA
(EQ. 7)
R NTC (T2 ) + Rs =
1.23V
= 22.78kΩ
54 μA
(EQ. 8)
From Equation 7 and Equation 8, the following can be
derived:
RNTC(T2 ) − RNTC(T1 ) = 2.78kΩ
(EQ. 9)
Substitution of Equation 6 into Equation 9 yields the required
nominal NTC resistor value:
2.78kΩ ⋅ e
RNTCTo =
e
1
b⋅(
)
T2 + 273
b⋅(
−e
1
)
To + 273
(EQ. 10)
1
b⋅(
)
T1 + 273
In some cases, the constant b is not accurate enough to
approximate the resistor value; manufacturers provide the
resistor ratio information at different temperatures. The
nominal NTC resistor value may be expressed in another
way as follows:
RNTCTo =
2.78kΩ
Λ
Λ
R NTC (T2 ) − R NTC (T1 )
Once RNTCTo and Rs is designed, the actual NTC resistance
at T2 and the actual T2 temperature can be found in:
RNTC _ T 2 = 2.78kΩ + RNTC _ T 1
T2 _ actual =
1
1 R NTC _ T2
ln(
) + 1 ( 273 + To )
b
R NTCTo
(EQ. 13)
− 273
(EQ. 14)
One example of using Equations 10, 11 and 12 to design a
thermal throttling circuit with the temperature hysteresis
+100°C to +105°C is illustrated as follows. Since T1 = +105°C
and T2 = +100°C, if we use a Panasonic NTC with b = 4700,
Equation 9 gives the required NTC nominal resistance as
R NTC_To = 431kΩ
The NTC thermistor datasheet gives the resistance ratio as
0.03956 at +100°C and 0.03322 at +105°C. The b value of
4700k in Panasonic datasheet only covers up to +85°C;
therefore, using Equation 11 is more accurate for +100°C
design and the required NTC nominal resistance at +25°C is
438kΩ. The closest NTC resistor value from manufacturers
is 470kΩ. So Equation 12 gives the series resistance as
follows:
Rs = 20kΩ − R NTC _ 105C = 20kΩ − 15.61kΩ = 4.39kΩ
The closest standard value is 4.42kΩ. Furthermore,
Equation 13 gives the NTC resistance at T2:
RNTC _ T 2 = 2.78kΩ + RNTC _ T 1 = 18.39kΩ
The NTC branch is designed to have a 470k NTC and a
4.42k resistor in series. The part number of the NTC
thermistor is ERTJ0EV474J. It is a 0402 package. The NTC
thermistor should be placed in the spot that gives the best
indication of the temperature of the voltage regulator. The
actual temperature hysteretic window is approximately
+105°C to +100°C.
(EQ. 11)
Λ
where R NTC (T ) is the normalized NTC resistance to its
nominal value. The normalized resistor value on most NTC
thermistor datasheets is based on the value at +25°C.
Once the NTC thermistor resistor is determined, the series
resistor can be derived by:
Rs =
1.20V
− R NTC (T1 ) = 20kΩ − R NTC_T1
60 μA
19
(EQ. 12)
FN6354.3
November 5, 2009
ISL6261A
10µA
R ocset
OCSET
VO
OC
Rs
VSUM
Internal to ISL6261A
DROOP
DFB
DROOP
VO
Cn
R drp2
1
Vdcr
R series
I
o
DCR
R par
R ntc
Rn
(Rntc +Rseries )
Rpar
R drp1
Rntc +Rseries +Rpar
FIGURE 9. EQUIVALENT MODEL FOR DROOP CIRCUIT USING DCR SENSING
Static Mode of Operation - Static Droop Using DCR
Sensing
G1, the gain of Vn to VDCR, is also dependent on the
temperature of the NTC thermistor:
The ISL6261A has an internal differential amplifier to
accurately regulate the voltage at the processor die.
G1 (T ) =
Δ
For DCR sensing, the process to compensate the DCR
resistance variation takes several iterative steps. Figure 2
shows the DCR sensing method. Figure 9 shows the
simplified model of the droop circuitry. The inductor DC
current generates a DC voltage drop on the inductor DCR.
Equation 15 gives this relationship.
V DCR = I o × DCR
(EQ. 15)
An R-C network senses the voltage across the inductor to
get the inductor current information. Rn represents the NTC
network consisting of Rntc, Rseries and Rpar. The choice of Rs
will be discussed in the next section.
The first step in droop load line compensation is to choose
Rn and Rs such that the correct droop voltage appears even
at light loads between the VSUM and VO nodes. As a rule of
thumb, the voltage drop across the Rn network, Vn, is set to
be 0.5 to 0.8 times VDCR. This gain, defined as G1, provides
a fairly reasonable amount of light load signal from which to
derive the droop voltage.
The NTC network resistor value is dependent on the
temperature and is given by Equation 16:
Rn (T ) =
( Rseries + Rntc ) ⋅ R par
Rseries + Rntc + R par
(EQ. 16)
Rn (T )
Rn (T ) + Rs
The inductor DCR is a function of the temperature and is
approximately given by Equation 18:
DCR(T ) = DCR25C ⋅ (1 + 0.00393 * (T − 25))
(EQ. 18)
in which 0.00393 is the temperature coefficient of the copper.
The droop amplifier output voltage divided by the total load
current is given by Equation 19:
Rdroop = G1(T) ⋅ DCR (T ) ⋅ k droopamp
(EQ. 19)
Rdroop is the actual load line slope. To make Rdroop
independent of the inductor temperature, it is desired to
have:
G1 (T ) ⋅ (1 + 0.00393 * (T − 25)) ≅ G1t arg et
(EQ. 20)
where G1target is the desired ratio of Vn/VDCR. Therefore, the
temperature characteristics G1 is described by Equation 21:
G 1 (T ) =
G 1 t arg et
(1 + 0.00393* (T − 25)
(EQ. 21)
For different G1 and NTC thermistor preference, Intersil
provides a design spreadsheet to generate the proper value
of Rntc, Rseries, Rpar.
Rdrp1 (R11 in Fig. 2) and Rdrp2 (R12 in Figure 2) sets the
droop amplifier gain, according to Equation 22:
k droopamp = 1 +
20
(EQ. 17)
Rdrp 2
R drp1
(EQ. 22)
FN6354.3
November 5, 2009
ISL6261A
After determining Rs and Rn networks, use Equation 23 to
calculate the droop resistances Rdrp1 and Rdrp2.
Rdrp 2 = (
Rdroop
DCR ⋅ G1(25 o C )
− 1) ⋅ Rdrp1
(EQ. 23)
Rdroop is 2.1mV/A per lntel® IMVP-6® specification.
response. Figure 11 shows the transient response when Cn
is too small. Vcore may sag excessively upon load
application to create a system failure. Figure 12 shows the
transient response when Cn is too large. Vcore is sluggish in
drooping to its final value. There will be excessive overshoot
if a load occurs during this time, which may potentially hurt
the CPU reliability.
The effectiveness of the Rn network is sensitive to the
coupling coefficient between the NTC thermistor and the
inductor. The NTC thermistor should be placed in close
proximity of the inductor.
To verify whether the NTC network successfully compensates
the DCR change over temperature, one can apply full load
current, wait for the thermal steady state, and see how much
the output voltage deviates from the initial voltage reading.
Good thermal compensation can limit the drift to less than
2mV. If the output voltage decreases when the temperature
increases, that ratio between the NTC thermistor value and
the rest of the resistor divider network has to be increased.
Following the evaluation board value and layout of NTC
placement will minimize the engineering time.
The current sensing traces should be routed directly to the
inductor pads for accurate DCR voltage drop measurement.
However, due to layout imperfection, the calculated Rdrp2
may still need slight adjustment to achieve optimum load line
slope. It is recommended to adjust Rdrp2 after the system
has achieved thermal equilibrium at full load. For example, if
the max current is 20A, one should apply 20A load current
and look for 42mV output voltage droop. If the voltage droop
is 40mV, the new value of Rdpr2 is calculated by:
R drp 2 _ new =
42 mV
( R drp 1 + R drp 2 ) − R drp 1
40 mV
(EQ. 24)
For the best accuracy, the effective resistance on the DFB
and VSUM pins should be identical so that the bias current
of the droop amplifier does not cause an offset voltage. The
effective resistance on the VSUM pin is the parallel of Rs and
Rn, and the effective resistance on the DFB pin is the parallel
of Rdrp1 and Rdrp2.
Dynamic Mode of Operation – Droop Capacitor
Design in DCR Sensing
Figure 10 shows the desired waveforms during load
transient response. Vcore needs to be as square as possible
at Icore change. The Vcore response is determined by several
factors, namely the choice of output inductor and output
capacitor, the compensator design, and the droop capacitor
design.
The droop capacitor refers to Cn in Figure 9. If Cn is
designed correctly, its voltage will be a high-bandwidth
analog voltage of the inductor current. If Cn is not designed
correctly, its voltage will be distorted from the actual
waveform of the inductor current and worsen the transient
21
Vcore
icore
ΔIcore
Vcore
ΔVcore
ΔVcore= ΔIcore×Rdroop
FIGURE 10. DESIRED LOAD TRANSIENT RESPONSE
WAVEFORMS
icore
Vcore
Vcore
FIGURE 11. LOAD TRANSIENT RESPONSE WHEN Cn IS TOO
SMALL
icore
Vcore
Vcore
FIGURE 12. LOAD TRANSIENT RESPONSE WHEN Cn IS TOO
LARGE
The current sensing network consists of Rn, Rs and Cn. The
effective resistance is the parallel of Rn and Rs. The RC time
constant of the current sensing network needs to match the
L/DCR time constant of the inductor to get correct
representation of the inductor current waveform. Equation 25
shows this equation:
⎛ R × Rs ⎞
L
⎟ × Cn
= ⎜⎜ n
DCR ⎝ Rn + Rs ⎟⎠
(EQ. 25)
Solving for Cn yields:
L
C n = DCR
Rn × Rs
Rn + Rs
(EQ. 26)
FN6354.3
November 5, 2009
ISL6261A
For example: L = 0.45µH, DCR = 1.1mΩ, Rs = 7.68kΩ, and
Rn = 3.4kΩ
in the FB pin. It is recommended to keep this resistor below
3k.
0.45μH
0.0011
Cn =
= 174nF
parallel(7.68k ,3.4k )
Droop using Discrete Resistor Sensing Static/Dynamic Mode of Operation
(EQ. 27)
Since the inductance and the DCR typically have 20% and
7% tolerance respectively, the L/DCR time constant of each
individual inductor may not perfectly match the RC time
constant of the current sensing network. In mass production,
this effect will make the transient response vary a little bit
from board to board. Compared with potential long-term
damage on CPU reliability, an immediate system failure is
worse. So it is desirable to avoid the waveforms shown in
Figure 11. It is recommended to choose the minimum Cn
value based on the maximum inductance so only the
scenarios of Figures 10 and 12 may happen. It should be
noted that, after calculation, fine-tuning of Cn value may still
be needed to account for board parasitics. Cn also needs to
be a high-grade cap like X7R with low tolerance. Another
good option is the NPO/COG (class-I) capacitor, featuring
only 5% tolerance and very good thermal characteristics. But
the NPO/COG caps are only available in small capacitance
values. In order to use such capacitors, the resistors and
thermistors surrounding the droop voltage sensing and
droop amplifier need to be scaled up 10X to reduce the
capacitance by 10X. Attention needs to be paid in balancing
the impedance of droop amplifier.
Dynamic Mode of Operation - Compensation
Parameters
The voltage regulator is equivalent to a voltage source equal
to VID in series with the output impedance. The output
impedance needs to be 2.1mΩ in order to achieve the
2.1mV/A load line. It is highly recommended to design the
compensation such that the regulator output impedance is
2.1mΩ. A type-III compensator is recommended to achieve
the best performance. Intersil provides a spreadsheet to
design the compensator parameters. Figure 13 shows an
example of the spreadsheet. After the user inputs the
parameters in the blue font, the spreadsheet will calculate
the recommended compensator parameters (in the pink
font), and show the loop gain curves and the regulator output
impedance curve. The loop gain curves need to be stable for
regulator stability, and the impedance curve needs to be
equal to or smaller than 2.1mΩ in the entire frequency range
to achieve good transient response.
Figure 3 shows a detailed schematic using discrete resistor
sensing of the inductor current. Figure 14 shows the
equivalent circuit. Since the current sensing resistor voltage
represents the actual inductor current information, Rs and Cn
simply provide noise filtering. The most significant noise
comes from the ESL of the current sensing resistor. A low
low ESL sensing resistor is strongly recommended. The
recommended Rs is 100Ω and the recommended Cn is
220pF. Since the current sensing resistance does not
appreciably change with temperature, the NTC network is
not needed for thermal compensation.
Droop is designed the same way as the DCR sensing
approach. The voltage on the current sensing resistor is
given by the following Equation 28:
Vrsen = Rsen ⋅ I o
(EQ. 28)
Equation 21 shows the droop amplifier gain. So the actual
droop is given by Equation 29:
⎛ Rdrp 2 ⎞
⎟
Rdroop = Rsen ⋅ ⎜1 +
⎜ R ⎟
drp
1
⎝
⎠
(EQ. 29)
Solving for Rdrp2 yields:
⎛ Rdroop ⎞
Rdrp 2 = Rdrp1 ⋅ ⎜⎜
− 1⎟⎟
⎠
⎝ Rsen
(EQ. 30)
For example: Rdroop = 2.1mΩ. If Rsen = 1m and Rdrp1 = 1k,
easy calculation gives that Rdrp2 is 1.1k.
The current sensing traces should be routed directly to the
current sensing resistor pads for accurate measurement.
However, due to layout imperfections, the calculated Rdrp2
may still need slight adjustment to achieve optimum load line
slope. It is recommended to adjust Rdrp2 after the system
has achieved thermal equilibrium at full load.
The user can choose the actual resistor and capacitor values
based on the recommendation and input them in the
spreadsheet, then see the actual loop gain curves and the
regulator output impedance curve.
Caution needs to be used in choosing the input resistor to
the FB pin. Excessively high resistance will cause an error to
the output voltage regulation due to the bias current flowing
22
FN6354.3
November 5, 2009
VSS
ISL6261A
FIGURE 13. AN EXAMPLE OF ISL6261A COMPENSATION SPREADSHEET
23
FN6354.3
November 5, 2009
ISL6261A
10µA
Rocset
OCSET
VO
OC
Rs
VSUM
Internal to ISL6261A
DROOP
DFB
Vrsen
Rsen
R drp1
VO
I
o
Cn
1
R drp2
DROOP
FIGURE 14. EQUIVALENT MODEL FOR DROOP CIRCUIT USING DISCRETE RESISTOR SENSING
Typical Performance (ISL6261 Data, Taken on ISL6261A Eval1 Rev.A Evaluation Board)
FIGURE 15. CCM EFFICIENCY, VID = 1.1V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
FIGURE 16. CCM LOAD LINE AND THE SPEC, VID = 1.1V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
FIGURE 17. DEM EFFICIENCY, VID = 0.7625V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
FIGURE 18. DEM LOAD LINE AND THE SPEC, VID = 0.7625V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
24
FN6354.3
November 5, 2009
ISL6261A
Typical Performance (ISL6261 Data, Taken on ISL6261A Eval1 Rev.A Evaluation Board) (Continued)
FIGURE 19. ENHANCED DEM EFFICIENCY, VID = 0.7625V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
FIGURE 20. ENHANCED DEM LOAD LINE, VID = 0.7625V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
FIGURE 21. ENHANCED DEM EFFICIENCY, VID = 1.1V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
FIGURE 22. ENHANCED DEM LOAD LINE, VID = 1.1V,
VIN1 = 8V, VIN2 = 12.6V AND VIN3 = 19V
5V/div
5V/div
0.5V/div
0.5V/div
1V/div
1V/div
10V/div
10V/div
FIGURE 23. SOFT-START, VIN = 19V, Io = 0A, VID = 1.5V,
Ch1: VR_ON, Ch2: VO, Ch3: PMON, Ch4: PHASE
25
FIGURE 24. SOFT-START, VIN = 19V, Io = 0A, VID = 1.1V,
Ch1: VR_ON, Ch2: VO, Ch3: PMON, Ch4: PHASE
FN6354.3
November 5, 2009
ISL6261A
Typical Performance (ISL6261 Data, Taken on ISL6261A Eval1 Rev.A Evaluation Board) (Continued)
5V/div
5V/div
0.1V/div
0.1V/div
1V/div
1V/div
10V/div
10V/div
FIGURE 25. VBOOT TO VID, VIN = 19V, Io = 2A, VID = 1.5V,
Ch1: CLK_EN#, Ch2: VO, Ch3: PMON,
Ch4: PHASE
FIGURE 26. VBOOT TO VID, VIN = 19V, Io = 2A, VID = 0.7625V,
Ch1: CLK_EN#, Ch2: VO, Ch3: PMON,
Ch4: PHASE
5V/div
0.5V/div
7.68ms
5V/div
10V/div
FIGURE 27. CLK_EN AND PGOOD ASSERTION DELAY,
VIN = 19V, Io = 2A, VID = 1.1V, Ch1: CLK_EN#,
Ch2: VO, Ch3: PGOOD, Ch4: PHASE
FIGURE 28. SHUT DOWN, VIN = 12.6V, Io = 2A, VID = 1.1V,
Ch1: VR_ON, Ch2: VO, Ch3: PGOOD,
Ch4: PHASE
FIGURE 29. SOFT START INRUSH CURRENT, VIN = 19V,
Io = 2A, VID = 1.1V, Ch1: DROOP-VO
(2.1mV = 1A), Ch2: VO, Ch3: Vcomp, Ch4: PHASE
FIGURE 30. VIN TRANSIENT TEST, VIN = 8Æ19V, Io = 2A,
VID = 1.1V, Ch2: VO, Ch3: VIN, Ch4: PHASE
26
FN6354.3
November 5, 2009
ISL6261A
Typical Performance (ISL6261 Data, Taken on ISL6261A Eval1 Rev.A Evaluation Board) (Continued)
FIGURE 31. C4 ENTRY/EXIT, VIN = 12.6V, Io = 0.7A,
HFM/LFM/C4 VID = 1.05V/0.8375V/0.7625V,
FDE = DPRSLPVR, Ch1: PMON, Ch2: VO,
Ch3: 40k/100pF FILTERED PMON, Ch4: PHASE
FIGURE 32. VID TOGGLING, VIN = 12.6V, Io= 16.5A,
HFM/LFM VID = 1.05V/0.8375V,
FDE = DPRSLPVR, Ch1: PMON, Ch2: VO,
Ch3: 40k/100pF FILTERED PMON, Ch4: PHASE
FIGURE 33. LOAD TRANSIENT RESPONSE IN CCM
VIN = 12.6V, Io = 2AÆ20A (100A/µs), VID = 1.1V,
Ch1: PMON, Ch2: VO, Ch3: 40k/100pF FILTERED
PMON, Ch4: PHASE
FIGURE 34. LOAD TRANSIENT RESPONSE IN CCM
VIN = 12.6V, Io = 20AÆ2A (50A/µs), VID = 1.1V,
Ch1: PMON, Ch2: VO, Ch3: 40k/100pF FILTERED
PMON, Ch4: PHASE
100A/us
FIGURE 35. LOAD TRANSIENT RESPONSE IN CCM
VIN = 12.6V, Io = 2AÆ20A (100A/µs)Æ2A (50A/µs),
VID = 1.1V, Ch1: PMON, Ch2: VO, Ch3: 40k/100pF
FILTERED PMON, Ch4: PHASE
27
50A/us
FIGURE 36. LOAD TRANSIENT RESPONSE IN EDEM
VIN = 8V, Io = 2AÅÆ20A, VID = 1.1V,
Ch1: Io, Ch2: VO, Ch3: PMON, Ch4: PHASE
FN6354.3
November 5, 2009
ISL6261A
Typical Performance (ISL6261 Data, Taken on ISL6261A Eval1 Rev.A Evaluation Board) (Continued)
100A/us
50A/us
FIGURE 37. LOAD TRANSIENT RESPONSE IN EDEM
VIN = 8V, Io = 2AÅÆ20A, VID = 1.1V,
Ch1: Io, Ch2: VO, Ch3: PMON, Ch4: PHASE
FIGURE 38. LOAD TRANSIENT RESPONSE IN EDEM
VIN = 8V, Io = 2AÅÆ20A, VID = 1.1V,
Ch1: Io, Ch2: VO, Ch3: PMON, Ch4: PHASE
120us
FIGURE 39. OVERCURRENT PROTECTION, VIN = 12.6V,
Io = 0AÆ28A, VID = 1.1V, Ch1: DROOP-VO
(2.1mV = 1A), Ch2: VO, Ch3: PGOOD,
Ch4: PHASE
FIGURE 40. OVERVOLTAGE (>1.7V) PROTECTION,
VIN = 12.6V, Io = 2A, VID = 1.1V,
Ch2: VO, Ch3: PGOOD, Ch4: PHASE
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
28
FN6354.3
November 5, 2009
ISL6261A Eval1 Evaluation Board Schematics
C18
P15
330PF
IN
J1
100
8
J3
10
R46
10UF
C30
2
R39
P34
C31
10UF
1UF
J4
C29
C28
0.01UF
J2
OUT
OUT
P32
P30 DNP
DNP
C25
3.57K 10K NTC
R31
8200PF
R27
4.53K
R29
R28
VSUM
0.068UF
C21
IN
P22
VCC_PRM
0.12UF
C19
1K
C7
10
9
1
1 2 2 5V
IN
VR_ON1
J16
R44
10K
R45
10K
3
1 S4
J19
OFF
2
VR_ON
ON
1
2 21
3 3
1X3
R34
0
R35
0
R15
330PF
2
11
+3.3V
+3.3V
R33
R47
10K
10K
R42
10K
R41
10K
R40
10K
R38
10K
R37
10K
R36
P33
P31
P28
P27
P25
P24
RTN
DFB
0.1UF
C16
5.23K
0
C26
C6
C15
R7
DNP R8 DNP
OUT
12
3.3V
10K
VSEN
0
P3
P23
R32
1000PF
OUT
13
5V
1
R43
1UF
0
OUT
14
MST7_SPST
DNP
R30
VDIFF1
J17
2 2 1
14
13
12
11
10
9
8
C23
C27
C14
P11
1000PF
R12
C11
P9
R6
R24
2.21K
R25
47PF
LGATE
GND_POWER
PHASE
UGATE
BOOT
P29
390PF
IN
IN
IN
IN
IN
IN
IN
+5V
P26
5.49K
0
0
DROOP
P20
P14
464K
ISL6261A
0.22UF
P4
P5
10UF
C2
VSSSENSE
150PF
U6
VID2
VID1
VID0
VCCP
LGATE
VSSP
PHASE
UGATE
BOOT
NC
P21
IN
C20
R11
0
FDE
PMON
RBIAS
VR_TT
NTC
SOFT
OCSET
VW
COMP
FB
P17
IN
GND_POWER
R23
C12
3V3
EP
R19
VID6
VID5
VID4
VID3
VID2
VID1
VID0
1UF
VDIFF
VSEN
RTN
DROOP
DFB
VO
VSUM
VIN
VSS
VDD
147K
FB
C9
COMP
R5
7
PGOOD
3V3
CLK_EN
DPRSTP
DPRSLPVR
VR_ON
VID6
VID5
VID4
VID3
OUT
1000PF
6.81K
C13
P8
VCORE
4
6
C17
PMON/PGD_IN
RBIAS
VR_TT
P12
IN
3
C24
J10
1X3
DNP
P1
R22
499
R20
0
DNP
R17 DNP R16
C8
R9
DNP
R13
VW
1
2
3
4
5
6
7
2
J15
1 1 2 2
1
2 21
3 3
PSI#
U1
1
5
SOFT
OCSET
DNP
IN
P19
P18
P16
P2
DNP
10K
10K
R21
10K
R14
10K
R10
R103
P7
2
VR_ON
DPRSLPVR
DPRSTP#
CLK_EN#
VIN
IN
NOTE:
RUN LGATE1 TRACE PARALLEL TO TRACE CONNECTING
PGND1 AND SOURCE OF Q3 AND Q4.
TITLE:
ISL6261 EVAL1
CONTROLLER
ENGINEER:
JIA WEI
DRAWN BY:
REV:
?
DATE:
MAR-14
SHEET:
1 OF
ISL6261A
6.34K
C3
VCCSENSE
+3.3V
P6
R3
10K
OUT
FDE
R4
VCC_PRM
0
+3.3V
1
Q5
R107
IN
0.015UF
C10
2N7002
IN
+3.3V
PGOOD
DPRSLPVR
SSL_LXA3025IGC
RED
34
2
D3
GRN
R1 510
3 R2 510 J9
1 12 2
1
29
PGOOD
IN
C92
DNP
DPRSTP#
FDE
SD05H0SK
+3.3V
DPRSLPVR
PSI#
PMON/PGD_IN
R108
10K
R18
10
9
8
7
6
ON
ON
ON
ON
ON
1
2
3
4
5
3
4
5
P10
+3.3V1
S1
J8
1 2 2 21
P13
Controller
FN6354.3
November 5, 2009
C34
VCCSENSE
IN
VSSSENSE
IN
J22 4
1
2
C55
22UF
C61
22UF
C67
C56
22UF
C62
22UF
C68
22UF
C57
22UF
C63
22UF
C69
22UF
22UF
C49
22UF
C50
22UF
C51
22UF
C39
22UF
C42
C43
330UF
C90
330UF
C44
330UF
ISL6261A
1
22UF
J13
C45
R82
C52
22UF
C58
22UF
C64
C53
22UF
C59
22UF
C65
22UF
C54
22UF
C60
22UF
C66
22UF
C70
C46
22UF
C47
22UF
C48
22UF
22UF
22UF
C37
C36
P41
P40
P39
P38
56UF
56UF
R83
22UF
22UF
C4
P35
10UF C5
10UF C5B
10UF
1UF
C32
C38
DNP
22UF
R54
22UF
DNP
0.1UF
0
R53
R52
C71
1
2
R60
BUS WIRE
22UF
J21 4
0
R50
1
2
L1
0.45UH
0.1UF
C91
3
DNP
1
DNP
J20 4
3
Q4
D2
IRF7832
Q2
R49
IRF7832
C35
R51
LGATE
0.22UF
1
7.68K
IN
0
Q3
VCC_PRM
VSUM
PHASE
C1
0.1UF
IN
R48
1
OUT
OUT
3
BOOT
IRF7821
Q1
2
IN
IRF7821
DNP
C33
UGATE
OUT
J5
VIN
C40
330UF
C89
330UF
C41
330UF
P37
J6
30
IN
P36
ISL6261A Eval1 Evaluation Board Schematics (Continued)
Power Stage
VCORE
1
OUT
GND_POWER
J14
OUT
FN6354.3
November 5, 2009
ISL6261A Eval1 Evaluation Board Schematics (Continued)
VSSSENSE
OUT
IN
W6
W5
W3
W2
V26
V24
V23
V4
V3
U25
U23
U22
U5
U4
U2
T25
T24
T22
T5
T3
T2
R24
R23
R4
R3
R1
P26
P25
P23
P22
P5
P4
K1
K4
K23
K26
L3
L6
L21
L24
M2
M5
M22
M25
N1
N4
N23
N26
AE7
W22
PSI
GTLREF
VID6
VID5
VID4
VID3
VID2
VID1
VID0
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
SOCKET1
V1
U26
U1
R26
AA4
AA3
AA1
Y26
Y25
Y23
Y22
Y5
Y4
Y2
Y1
W25
W24
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
AE1
AD25
AD22
AD19
AD16
AD13
AD11
AD8
AD5
AD2
AC24
AC21
AC19
AC16
AC14
AC11
AC8
AC6
AC3
AB26
AB23
AB19
AB16
AB13
AB11
AB8
AB4
AB1
AA25
AA22
AA19
AA16
AA14
AA11
AA8
AA5
AA2
Y24
Y21
Y6
Y3
W26
W23
W4
W1
V25
V22
V5
V2
U24
U21
U6
U3
T26
T23
T4
T1
R25
R22
R5
R2
P24
P21
P6
P3
ISL6261A
INTEL_IMPV6
COMP3
COMP1
COMP2
COMP0
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
GND_POWER
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
INTEL_IMPV6
A3
A5
A6
A21
A22
A24
A25
B1
B2
B3
B4
B5
B22
B23
B25
C1
C3
C4
C6
C7
C20
C21
C23
C24
C26
D2
D3
D5
D6
D7
D20
D21
D22
D24
D25
E1
E2
E4
E5
E22
E23
E25
E26
F1
F3
F4
F6
F21
F23
F24
SOCKET1
AF20
AF18
AF17
AF15
AF14
AF12
AF10
AF9
AE20
AE18
AE17
AE15
AE13
AE12
AE10
AE9
AD18
AD17
AD15
AD14
AD12
AD10
AD9
AD7
AC18
AC17
AC15
AC13
AC12
AC10
AC9
AC7
AB20
AB18
AB17
AB15
AB14
AB12
AB10
AB9
AB7
AA20
AA18
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
G21
J6
J21
K6
K21
M6
M21
N6
N21
R6
R21
T6
T21
V6
V21
W21
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSSSENSE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCCP
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
INTEL_IMPV6
SOCKET1
A7
A9
A10
A12
A13
A15
A17
A18
A20
B7
B9
B10
B12
B14
B15
B17
B18
B20
C9
C10
C12
C13
C15
C17
C18
D9
D10
D12
D14
D15
D17
D18
E7
E9
E10
E12
E13
E15
E17
E18
E20
F7
F9
F10
F12
F14
F15
F17
F18
F20
AA7
AA9
AA10
AA12
AA13
AA15
AA17
VCCA
VCCSENSE
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
F26
G2
G3
G5
G6
G22
G24
G25
H1
H2
H4
H5
H22
H23
H25
H26
J1
J3
J4
J23
J24
J26
K2
K3
K5
K22
K24
K25
L1
L2
L4
L5
L22
L23
L25
L26
M1
M3
M4
M23
M24
M26
N2
N3
N5
N22
N24
N25
P1
P2
31
IN
VCORE
AF7
A4
A8
A11
A14
A16
A19
A23
A26
B6
B8
B11
B13
B16
B19
B21
B24
C2
C5
C8
C11
C14
C16
C19
C22
C25
D1
D4
D8
D11
D13
D16
D19
D23
D26
E3
E6
E8
E11
E14
E16
E19
E21
E24
F2
F5
F8
F11
F13
F16
F19
F22
F25
G1
G4
G23
G26
H3
H6
H21
H24
J2
J5
J22
J25
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
B26
VCCSENSE
OUT
PSI#
AE6
OUT
AD26
AE2 VID6 OUT
AF2 VID5 OUT
AE3 VID4 OUT
AF4 VID3 OUT
AE5 VID2 OUT
AF5 VID1 OUT
AD6 VID0 OUT
AF26
AF25
AF23
AF22
AF1
AE25
AE24
AE22
AE21
AD24
AD23
AD21
AD20
AD4
AD3
AD1
AC26
AC25
AC23
AC22
AC20
AC5
AC4
AC2
AC1
AB25
AB24
AB22
AB21
AB6
AB5
AB3
AB2
AA26
AA24
AA23
AA21
AA6
AF24
AF21
AF19
AF16
AF13
AF11
AF8
AF6
AF3
AE26
AE23
AE19
AE16
AE14
AE11
AE8
AE4
Socket
FN6354.3
November 5, 2009
ISL6261A Eval1 Evaluation Board Schematics (Continued)
J11
J12
Dynamic Load
+12V
3
4
8
7
6
R74
5
249
HIP2100
R73
49.9K
2
3
1
1
BAV99
HUF76129D3S
Q15
1
2
GND_POWER
ON
R72
2
10UF
499
C81
3
R71
+12V
Q14
D1
3
S5 1
OFF
4 J23
ISL6261A
+12V
1
2
R75
249
2N7002
VCORE
IN
3
2
LO
VSS
LI
HI
0.12
1UF
VDD
HB
HO
HS
2
1
U5
3
32
C80
0.1
R76
GND_POWER
FN6354.3
November 5, 2009
ISL6261A Eval1 Evaluation Board Schematics (Continued)
9
MST7_SPST
10
GND
Y8
U4
G1
VCC
G2
A2
Y1
A3
Y2
A4
Y3
A5
Y4
A6
Y5
A7
Y6
A8
Y7
HC540
11
Y8
20
19
18
+3.3V_GEY
C74
0.1UF
+3.3V_GEY
17
16
15
12
2
2
+3.3V_GEY
R59
10K
R61
10K
R62
10K
10K
J25
1 2 2
1
2
+3.3V_GEY
10K
10K
3
EVQPA
PSI# S7
R102
R58
R64
10K
C76
10K
R57
4
LOOP
+3.3V_GEY
0.1UF
+3.3V
J24
1 1 2 2 +3.3V_GEY
10K
R56
C87
1X3
15PF
15PF
1
2
3
4
5
6
7
Vcc
1A
1Y
2A
2Y
3A
3Y
GND
AC04
6A
6Y
5A
5Y
4A
4Y
14
13
12
11
10
9
8
4
3
EVQPA
PSI#
1
1
2 21
3 3
J7
EVQPA
1
11
4
1UF
10K
3
DPRSLP
S6
14
13
S2
1
C86
U12
R77
MODE TRANS
1
R55
C85
+3.3V_GEY
A1
GND
12
+3.3V
BAV99
Y7
3
EVQPA
J28
1 1 2 2
3
A8
DNP
4
P45
Y6
CLK_EN#
13
P43
A7
IN
14
C79
Y5
0
R67
0.01UF
A6
15
1
2
P42
Y4
16
RESETS8
R80 0
8
A5
17
S9
8
Y3
1UF
PIC16F874 +3.3V_GEYR69
R104
10K
2
HCM49
2
1
7
A4
C73
0.1UF
7
28
1
R79 0
9
Y2
18
OUT
OUT
OUT
C88
6
A3
19
VDD
VDD
C78
BAV99
5
10
Y1
6
29
OUT
DELAY
DPRSLPVR
U11
18
3
10K
10K
R101
10K
R98
10K
R95
10K
R92
10K
R89
11
G2
A2
+3.3V_GEY
31
DIRECT
OUT
DNP
7
4
A1
20
DNP
30
P44
6
12
25
26
27
VCC
HC540
11
R78 0
5
3
U3
G1
Y8
R106
DNP
4
12
11
10
9
8
2
HC540
PSI#
DPRSTP#
PGD_IN
VR_ON1
2
1
3
1
2
3
4
5
6
7
14 14
13 13
1
GND
12
33
34
19
20
21
22
23
24
C84
2
10K
R86
R83
U9
1
10
Y7
13
OUT
OUT
OUT
OUT
OUT
OUT
OUT
ISL6261A
9
MST7_SPST
Y6
A8
38
39
40
41
2
3
4
5
0
7
8
A7
14
S3
10K
10K
R100
10K
R97
10K
R94
10K
R91
10K
R88
6
Y5
12
13
15
R70 0
7
5
A6
16
R105
6
4
Y4
VID0
VID1
VID2
VID3
VID4
VID5
VID6
8
9
10
11
14
15
16
17
DNP
5
3
A5
17
RB0
RB1
RB2
RB3
RB4
RB5
RB6
RB7
NC
NC
RA0
RA1
RA2
RA3
RA4
RA5
OSC1
OSC2
MCLR
R68
4
2
Y3
10K
3
14 14
13 13
12 12
11 11
10 10
9 9
8 8
1
2
3
4
5
6
7
1
A4
18
R65
1
10K
R85
U8
2
10
Y2
0.1UF
C77
9
Y1
A3
C72
RC0
RC1
RC2
RC3
RC4
RC5
RC6
RC7
NC
NC
RD0
RD1
RD2
RD3
RD4
RD5
RD6
RD7
RE0
RE1
RE2
VSS
VSS
0.1UF
10K
10K
R99
10K
R96
10K
R93
10K
R90
8
MST7_SPST
R82
33
7
7
A2
19
32
35
36
37
42
43
44
1
10K
6
6
G2
+3.3V_GEY
R66
5
5
A1
20
10K
4
3
4
VCC
R63
3
2
U2
G1
C75
2
14 14
13 13
12 12
11 11
10 10
9 9
8 8
1
2
3
4
5
6
7
U10
1
0.1UF
1
10K
R87
U7
10K
R84
R81
Geyserville Transition Gen.
J29
1 2 2
REV:
TITLE:
ISL6261 EVAL1
GEYSERVILLE TRANSITION GEN.
ENGINEER:
DATE:
MARJIA WEI
DRAWN BY:
SHEET:
5
FN6354.3
November 5, 2009
ISL6261A
Package Outline Drawing
L40.6x6
40 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 3, 10/06
4X 4.5
6.00
36X 0.50
A
B
6
PIN 1
INDEX AREA
6
PIN #1 INDEX AREA
40
31
30
1
6.00
4 . 10 ± 0 . 15
21
10
0.15
(4X)
11
20
TOP VIEW
0.10 M C A B
40X 0 . 4 ± 0 . 1
4 0 . 23 +0 . 07 / -0 . 05
BOTTOM VIEW
SEE DETAIL "X"
0.10 C
0 . 90 ± 0 . 1
(
C
BASE PLANE
( 5 . 8 TYP )
SEATING PLANE
0.08 C
SIDE VIEW
4 . 10 )
( 36X 0 . 5 )
C
0 . 2 REF
5
( 40X 0 . 23 )
0 . 00 MIN.
0 . 05 MAX.
( 40X 0 . 6 )
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 indentifier may be
either a mold or mark feature.
34
FN6354.3
November 5, 2009