OSRAM DRAGONeye G2 Technical Information Benefits Compact high-flux LED-minispot Doubled flux compared to G1 Very long lifetimes of 70 000 hours Integrated heat-sink and 15° optics IP65 rating for demanding outdoor applications Applications Shop - Cabinet & Shelf Hospitality - Restaurant & Hotel Architectural - robust outdoor minispot Technical Operating Data Product current typ. voltage [mA] [V] power [W] radiance angle [°] CCT [K] typ. lum. flux [lm] typ. lum. intensity [cd] CRI [Ra] typ. efficacy [lm/W] DE1-W4F-830-G2 350 3.1 1.1 15 3000 88 1080 >80 80 DE1-W4F-850-G2 350 3.1 1.1 15 5000 106 1300 >80 96 Product max. current [mA] min. voltage [V] max. max. voltage power [W] [V] DE1-W4F-830-G2 500 2.8 3.5 1.75 DE1-W4F-850-G2 500 2.8 3.5 1.75 ESD protection Tc [°C] IP rating L70B50 @ Ta=25°C [h] contact 4kV air 8kV 90 65 70000 90 65 70000 All Data are related to the entire module Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data Technical Features Module ready to use with two cables: Max. tc temperature of 90oC (see IEC/PAS 62717) - red cable (+ pole) L70B50 >=70,000 hours at Ta=25oC - black cable (- pole) Energy efficiency class: A++ Cable length 500 mm, cable Ø 1.6 mm/AWG 22 Heat sink and lens-optics integrated Best efficacy in combination with OSRAM OPTOTRONIC® constant current control gears IP65 for outdoor use Modul efficacy up to 96 lm/W DRAGONeye G2 – 09.06.2014 Page 1 OSRAM Minimum and Maximum Ratings Product operating temperature storage temperature ambient temperature max. current at tc-point [C°]* [C°]* range [C°]* [mA]* max. reverse voltage [V]* DE1-W4F-830-G2 -25 … 90 -25 … 85 -25 … 55 500 0 DE1-W4F-850-G2 -25 … 90 -25 … 85 -25 … 55 500 0 *) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module. Exceeding maximum ratings for operating current will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module must be measured at the tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. For exact location of the tc-point see drawing below. Dimensions & Mechanical data Dimension (mm) Ø23 Mounting M10 thread included Optics PC lens Weight 8 grams DRAGONeye G2 – 09.06.2014 Page 2 OSRAM Standard Compliance Safety EN 62031, IEC 60598-1, UL 8750 EMC EN 55015, EN 61547 Eye Security EN 62471 Ingress Production Dry Location, IP 20 Environment RoHS Safety Information The LED module itself and all its components must not be mechanically stressed. Assembly must not damage or destroy conducting paths on the circuit board. To avoid mechanical damage to the connecting cables, the module should be attached securely to the intended substrate. Heavy vibration should be avoided. In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilised power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. The declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information"). OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Correct electrical polarity needs to be obsered. Wrong polarity will destory the module and will result in no light emission. Pay attention to standard ESD precautions when installing the module. The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. Damage by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. Pay attention not to exceed the maximum operation temperature at tc point when the modules are used in enclosed environment. DRAGONeye G2 – 09.06.2014 Page 3 OSRAM Ordering Guide Product Name Product Code DRAGONeye G2 DE1-W4F-830-G2 Product Number : Product Number: Piece per box single product (EAN10) shipping box (EAN40) 4052899043053 4052899043077 264 DRAGONeye G2 DE1-W4F-850-G2 4052899042872 4052899042896 264 Sales and Technical Support OSRAM GmbH Marcel-Breuer-Straße 6 80807 Munich, Germany www.osram.com +49.89.6213-0 (Headquarter) +49.89.6213-6000 (Customer-Service-Center) DRAGONeye G2 – 09.06.2014 Sales and technical support is given by the local OSRAM subsidiaries. On the OSRAM website all subsidiaries are lis-ted with complete address and phone numbers. Page 4