LTC3110 - 2A Bidirectional Buck-Boost DC/DC Regulator and Charger/Balancer

LTC3110
2A Bidirectional Buck-Boost
DC/DC Regulator and
Charger/Balancer
DESCRIPTION
FEATURES
VCAP Operating Range: 0.1V to 5.5V
VSYS Operating Range: 1.71V to 5.25V
Automatic Switchover from Charge to Backup Mode
Programmable ±2% Accurate Charge Input Current
Limit from 125mA to 2A
n±1% Backup Voltage Accuracy
n Automatic Backup Capacitor Balancing
n Fixed 1.2MHz Switching Frequency
n Burst Mode® Operation: 40μA Quiescent Current
n Built-In Programmable Multipurpose Comparator
with Open-Collector Output
n Open-Collector Outputs to Indicate Direction of
Operation and End of Charge
n Thermally Enhanced TSSOP-24 and 4mm × 4mm
QFN-24 Packages
n
n
n
The LTC®3110 is a 2A bidirectional buck-boost DC/DC
regulator with capacitor charger and balancer. Its wide
0.1V to 5.5V capacitor/battery voltage and 1.8V to 5.25V
system backup voltage ranges make it well suited to a
wide variety of backup applications using supercapacitors
or batteries. A proprietary low noise switching algorithm
optimizes efficiency with capacitor/battery voltages that
are above, below or equal to the system output voltage.
n
The LTC3110 can autonomously transition from charge
to backup mode or switch modes based on an external
command. Pin-selectable Burst Mode operation reduces
standby current and improves light-load efficiency, which
combined with a 1μA shutdown current make the LTC3110
ideally suited for backup applications. Additional features
include voltage supervisors for direction control and end of
charge, and a general purpose comparator with open-collector output for interfacing with a µC. The LTC3110 is available in thermally enhanced, low profile 24-lead TSSOP and
4mm × 4mm QFN packages.
APPLICATIONS
n
n
n
n
Supercapacitor Backup Converter and Charger
Battery Backup Converter and Charger
Servers, RAID Systems
RF Systems with Battery/Capacitor Backup
L, LT, LTC, LTM, Burst Mode, Linear Technology and the Linear logo are registered trademarks
and PowerPath is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
TYPICAL APPLICATION
ICHARGE
FB
MAIN
STEP-DOWN DC/DC
0.1V UP TO 5.5V
10F
1960k
2.2µH
1µF
51.1Ω
SW2 SVSYS
VCAP SW1
FBVCAP
220nF
VSYS
VSYS
3.25V
2A
47µF
RSEN
1.50k
CMPIN
0.1µF
VMID
976k
LTC3110
2.5V
1.8V
SYSTEM
DC/DC
REGULATORS
1.2V
FB
221k
1000k
MODE
RUN
SGND
PGND
DIR
CHRG
CAPOK
CMPOUT
µC
END OF CHRG
CAPLOW
12V BUS
SUPERVISOR
3110 TA01a
For more information www.linear.com/LTC3110
1.0
90
0.8
85
0.6
80
0.4
75
0.2
70
1000k
1.2
VSYS = 3.25V
ISYS = 0.5A
95
PROG
13.7k
523k
100
1.2
1.8
2.4
3.0
3.6
4.2
4.8
5.4
POWER LOSS (W)
10F
Backup Mode Efficiency
IBACKUP
EFFICIENCY (%)
12V
BUS
0
VCAP (V)
3110 TA01b
3110fa
1
LTC3110
ABSOLUTE MAXIMUM RATINGS
(Note 1)
VCAP, VSYS, SVSYS, VMODE, VCMPIN,
VDIR, VRUN, VCAPOK, VCMPOUT, VCHRG....... –0.3V to 6V
RSEN DC Current ...................................................... 1.6A
Operating Junction Temperature Range
(Notes 2, 3)............................................. –40°C to 150°C
Storage Temperature Range................... –65°C to 150°C
Lead Soldering Temperature (Soldering, 10 sec)
TSSOP............................................................... 300°C
Reflow Peak Body Temperature (30sec max)
QFN.................................................................... 260°C
PIN CONFIGURATION
TOP VIEW
5
20 SW1
SGND
6
25
PGND
24 23 22 21 20 19
CMPIN 1
7
RUN
8
17 SW2
FB
9
16 SW2
PROG 10
15 VSYS
CHRG 11
14 RSEN
SVSYS 12
13 VSYS
18 SW1
FBVCAP 2
19 PGND
DIR
VCAP
FBVCAP
VCAP
21 SW1
17 SW1
SGND 3
18 PGND
16 PGND
25
PGND
DIR 4
15 PGND
RUN 5
14 SW2
FB 6
13 SW2
7
8
9 10 11 12
VSYS
4
VMID
CMPIN
RSEN
22 VCAP
CAPOK
MODE
VSYS
23 VCAP
3
CMPOUT
2
SVSYS
CMPOUT
TOP VIEW
MODE
24 VMID
CHRG
1
PROG
CAPOK
UF PACKAGE
24-LEAD (4mm × 4mm) PLASTIC QFN
FE PACKAGE
24-LEAD PLASTIC TSSOP
TJMAX = 150°C, θJA = 33°C/W, θJC = 5°C/W, 4 LAYER BOARD
EXPOSED PAD (PIN 25) IS PGND, MUST BE SOLDERED TO PCB
TJMAX = 150°C, θJA = 37°C/W, θJC = 4.5°C/W, 4 LAYER BOARD
EXPOSED PAD (PIN 25) IS PGND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
(http://www.linear.com/product/LTC3110#orderinfo)
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC3110EFE#PBF
LTC3110EFE#TRPBF
LTC3110FE
24-Lead Plastic TSSOP
–40°C to 125°C
LTC3110IFE#PBF
LTC3110IFE#TRPBF
LTC3110FE
24-Lead Plastic TSSOP
–40°C to 125°C
LTC3110HFE#PBF
LTC3110HFE#TRPBF
LTC3110FE
24-Lead Plastic TSSOP
–40°C to 150°C
LTC3110EUF#PBF
LTC3110EUF#TRPBF
3110
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 125°C
LTC3110IUF#PBF
LTC3110IUF#TRPBF
3110
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 125°C
LTC3110HUF#PBF
LTC3110HUF#TRPBF
3110
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
3110fa
2
For more information www.linear.com/LTC3110
LTC3110
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VCAP = 3.3V, VSYS = 3.3V, VDIR = VSGND, VMODE = VRUN
= VSYS = SVSYS unless otherwise noted.
PARAMETER
CONDITIONS
VCAP No-Load Operating Range in Backup Operation
VSYS ≥ 1.8V
VCAP Start-Up
VSYS Operating Range in Charge Operation
Undervoltage Lockout Threshold
VSYS Ramping Down, VCAP = 0V
VSYS Ramping Up, VCAP = 0V
l
VCAP Ramping Down, VSYS = 0V, VRUN = VCAP
VCAP Ramping Up, VSYS = 0V, VRUN = VCAP
l
0°C < TJ < 85°C (Note 5)
–40°C < TJ < 150°C
l
FB Feedback Voltage
MIN
TYP
0.1
VSYS < Undervoltage Lockout Threshold
l
1.8
VDIR = VSYS
l
1.8
5.5
FBVCAP End-of-Charge Threshold Rising
DIR = VSYS
l
FBVCAP End-of-Charge Threshold Falling
DIR = VSYS
l
FBVCAP Input Current
VFBVCAP = 1.1V
FBVCAP Overcharge Threshold Rising
V
V
V
1.71
V
V
1.71
V
V
0.6
0.6
0.608
0.611
V
V
0.1
50
nA
1.095
1.117
1.55
FB Feedback Pin Input Current
UNITS
5.25
1.55
0.592
0.589
MAX
V
1.040
1.061
0.1
50
nA
1.125
1.150
1.175
V
FBVCAP Overcharge Hysteresis
V
35
mV
VMODE = 0V
40
µA
Quiescent Current, End of Charge (IVCAP + IVSYS + ISVSYS) VDIR = VSYS
40
µA
Quiescent Current, Burst Mode Operation
(IVCAP + IVSYS + ISVSYS)
Quiescent Current, Shutdown (IVCAP)
VRUN = 0V, VSYS = SVSYS = 0V
Peak Current Limit in Backup Operation
(Note 4)
0.05
1
µA
5
6
7
A
DC Current Limit in Backup Operation
(Note 4)
3.5
4.5
Peak Current Limit in Charge Operation
(Note 4)
5
6
7
A
Reverse Current Limit in Backup Operation
(Note 4)
1
1.2
2
A
Switch Leakage
Switch B, C: VCAP = VSW1 = 5.5V,
VSYS = VSW2 = 5.25V,
0.1
µA
Switch A, D: VCAP = 5.5V, VSYS = 5.25V
VSW1 = VSW2 = 0V
0.1
µA
Switch A (Note 6)
Switch B (Note 6)
Switch C (Note 6)
Switch D Including Sense Resistor (Note 6)
64
49
49
86
mΩ
mΩ
mΩ
mΩ
Switch On-Resistance
Oscillator Frequency
Soft Start-Up Time in Backup Mode
Maximum Duty Cycle in Boost Mode
l
VCAP = 0.2V
VSYS = 0.2V
From VRUN rising to VFB = 90%
l
VCAP = 0.2V
Minimum Duty Cycle in Buck Mode
MODE Input Logic Threshold
l
900
1200
300
300
1500
kHz
kHz
kHz
0.8
1.3
1.8
ms
91
93
98
96
%
%
0
%
0.3
V
V
l
Enable Burst Mode Operation
Enable PWM Mode Operation
A
1
MODE Input Pull-Down Resistor
6
MΩ
DIR Threshold Rising
l
1.073
1.095
1.117
V
DIR Threshold Falling
l
1.024
1.045
1.066
V
DIR Hysteresis
l
30
DIR Input Current
VDIR = 1.1V
50
70
mV
0.1
50
nA
3110fa
For more information www.linear.com/LTC3110
3
LTC3110
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VCAP = 3.3V, VSYS = 3.3V, VDIR = VSGND, VMODE = VRUN
= VSYS = SVSYS unless otherwise noted.
PARAMETER
CONDITIONS
CMPIN Threshold Rising
CMPIN Threshold Falling
CMPIN Input Current
l
MIN
TYP
MAX
UNITS
0.638
0.65
0.662
V
0.575
0.59
0.605
V
0.1
50
nA
VCMPIN = 5.5V
PROG Voltage
VFBVCAP = 1V, DIR = VSYS
0.6
V
PROG Current Gain
DIR = VSYS
200
µA/A
IVSYS Input Current Limit
RPROG = 24.3k (Notes 7, 8), DIR = VSYS
RPROG = 24.3k (Notes 7, 8, 9), DIR = VSYS,
TJ = –40°C to 125°C
RPROG = 12.1k (Notes 7, 8), DIR = VSYS
RPROG = 12.1k (Notes 7, 8, 9), DIR = VSYS,
TJ = –40°C to 125°C
RPROG = 6.04k (Notes 7, 8), DIR = VSYS
RPROG = 6.04k (Notes 7, 8, 9), DIR = VSYS,
TJ = –40°C to 125°C
RPROG = 3.01k (Notes 7, 8), DIR = VSYS
RPROG = 3.01k (Notes 7, 8, 9), DIR = VSYS,
TJ = –40°C to 125°C
RPROG = 1.5k (Notes 7, 8), DIR = VSYS
RPROG = 1.5k (Notes 7, 8, 9), DIR = VSYS,
TJ = –40°C to 125°C
VMID to VCAP Voltage Ratio
VMID = Open Load, VCAP = 5V
VMID Balancing Current
VCAP = 5V, VMID = 5V
VCAP = 5V, VMID = 0V
l
l
119
115
123
123
128
135
mA
mA
241
234
248
248
255
270
mA
mA
487
473
497
497
507
525
mA
mA
977
948
997
997
1017
1046
mA
mA
1960
1900
2000
2000
2040
2100
mA
mA
0.492
0.5
0.508
150
300
–300
–150
mA
mA
VMID Current in Shutdown
VRUN = 0V
0.1
1
µA
VMID Suspend Charging Threshold
VMID Rising, VCAP = 5V
VMID Falling, VCAP = 5V
2.6
2.4
2.62
V
V
CHRG, CAPOK, CMPOUT Open-Drain Output Voltage
I = 10mA
0.1
0.3
V
l
RUN Input Logic Threshold
l
RUN Pull-Down Resistor
Note 2: The LTC3110 is tested under pulsed load conditions such that
TJ ~ TA. The LTC3110E is guaranteed to meet performance specifications
from 0°C to 85°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LTC3110I is guaranteed to meet specifications over the –40°C to 125°C
operating junction temperature range. The LTC3110H is guaranteed
to meet specifications over the full –40°C to 150°C operating junction
temperature range. High temperatures degrade operating lifetime;
operating life time is derated for junction temperatures greater than 125°C.
Note that the maximum ambient temperature consistent with these
specifications is determined by specific operating conditions in
conjunction with board layout, the rated package thermal impedance
and other environmental factors. The junction temperature (TJ, in °C) is
calculated from the ambient temperature (TA, in °C) and power dissipation
(PD, in watts) according to the formula:
TJ = TA + (PD • θJA),
0.3
1
6
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
2.38
V
MΩ
Note 3: This IC includes overtemperature protection that is intended to
protect the device during momentary overload conditions. The maximum
rated junction temperature will be exceeded when this protection is active.
Continuous operation above the specified absolute maximum operating
junction temperature may impair device reliability or permanently damage
the device.
Note 4: Current measurements are performed when the LTC3110 is
not switching. The current limit values measured in operation will be
somewhat higher due to the propagation delay of the comparators.
Note 5: Guaranteed by design characterization and correlation with
statistical process controls.
Note 6: Guaranteed by design, correlation and bench measurements.
Note 7: Current measurements are made when the output is not switching.
Note 8: Accuracy of this specification is directly related to the accuracy of
the resistor used to program the parameter.
Note 9: The Input Current Limit is reduced at junction temperatures above
125°C. See Thermal Foldback of Charge Current in the Operation section,
and the graph VPROG Programming Voltage vs Temperature in the Typical
Performance Characteristics section.
where θJA (in °C/W) is the package thermal impedance.
3110fa
4
For more information www.linear.com/LTC3110
LTC3110
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs VCAP Voltage
Burst Mode Efficiency
VSYS = 3.25V
PWM MODE
95
EFFICIENCY (%)
80
75
ISYS = 0.2A
ISYS = 0.5A
ISYS = 1A
ISYS = 2A
70
65
0.5
1.5
2.5
3.5
VCAP (V)
4.5
80
75
70
0.001
0.01
ISYS (A)
IVSYS (mA)
IVSYS (A)
3
2
2
1
3
VCAP (V)
400
125
350
115
300
105
250
200
100
0
5 5.5
4
0
2
1
3
VCAP (V)
180
170
VCAP < ~75% • VSYS
80
4
60
TJ = 85°C
TJ = 25°C
55
0
0.5
1
1.5
2
2.5 3
VCAP (V)
3.5
4
4.5
5
150
140
130
120
110
100
95
75
45
1.5
2
2.5
3
3.5
4
4.5
105
90
3.5
4
4.5
5
5.5
3110 G08
TJ = 85°C
85
80
75
TJ = 25°C
70
TJ = 0°C
60
3
TJ = 155°C
TJ = 125°C
95
60
1.5
2.5
VSYS < ~75% • VCAP
100
65
2
5.5
5
3110 G06
70
VSYS (V)
3110 G07
VCAP > ~75% • VSYS
TJ = 155°C
TJ = 130°C
TJ = 85°C
TJ = 25°C
TJ = 0°C
TJ = –45°C
RDS(ON) of SWD Static
Including Sense Resistor
90
TJ = 0°C
TJ = –45°C
0
5.5
4.5
VCAP (V)
80
50
45
RDS(ON) (mΩ)
RDS(ON) (mΩ)
75
TJ = 125°C
3.5
VCAP (V)
55
5 5.5
VSYS > ~75% • VCAP
TJ = 155°C
TJ = 130°C
TJ = 85°C
TJ = 25°C
TJ = 0°C
TJ = –45°C
160
65
2.5
85
RDS(ON) of SWD Dynamic
Including Sense Resistor
TJ = 155°C
1.5
3110 G05
RDS(ON) of SWA Static
70
0.5
65
U_VSYS = 1.8V
U_VSYS = 3.3V
U_VSYS = 5.25V
50
1.0
RDS(ON) of SWA Dynamic
135
3110 G04
85
70
450
150
U_VSYS = 1.8V
U_VSYS = 3.3V
U_VSYS = 5.25V
1.5
VSYS = 3.3V
RPROG = 3.01k
3110 G03
RDS(ON) (mΩ)
PULSED LOAD T = 1s
40% DUTY CYCLE
0
80
Maximum Load Current
in Burst Mode Operation
4
0
2.0
3110 G02
Maximum Load Current
in PWM Mode
1
90
50
0.5
0.1
3110 G01
5
2.5
60
VCAP = 5V, VSYS = 3.3V
VCAP = 2.5V, VSYS = 1.8V
5.5
100
TJ = –45°C
1.5
2
2.5
3
3.5
VSYS (V)
4
4.5
3110 G09
3110fa
For more information www.linear.com/LTC3110
5
POWER LOSS (W)
85
EFFICIENCY (%)
85
90
EFFICIENCY (%)
Charge Efficiency
90
RDS(ON) (mΩ)
100
TA = 25°C unless otherwise noted
LTC3110
TYPICAL PERFORMANCE CHARACTERISTICS
TJ = 155°C
TJ = 125°C
TJ = 85°C
TJ = 25°C
TJ = 0°C
TJ = –40°C
2.5
3.5 4 4.5
VCAP (V)
3
5
5.5
6
Switch Leakage vs Temperature
TJ = 155°C
TJ = 125°C
TJ = 85°C
TJ = 25°C
TJ = 0°C
TJ = –40°C
2
2.5
3
3.5 4 4.5
VSYS (V)
0.5
0
1
2
3
VCAP (V)
4
VFB CHANGE FROM 25°C (%)
VFB CHANGE FROM VCAP = 2.4V (%)
PWM MODE
Burst Mode
OPERATION
–1.0
5
5.5
0.5
Burst Mode
OPERATION
0
PWM
MODE
–0.5
800
600
VSYS = 3.3V
VSYS = 1.8V
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
VCAP (V)
3110 G16
30
55
80
105 130 155
3110 G12
VSYS Load Regulation
1.0
–5
75
35
115
0.5
PWM MODE
0
Burst Mode
OPERATION
–0.5
–1.0
155
0
0.5
1.0
2.5
1.5
2.0
ILOAD (A)
3.0
3110 G15
Switching Frequency
vs Temperature
Switching Frequency vs VSYS
1.0
1200
CHANGE FROM 25°C (%)
SWITCHING FREQUENCY (kHz)
SWITCHING FREQUENCY (kHz)
5
3110 G14
1400
1000
200
1.0
TJ (°C)
Switching Frequency vs VCAP
FREQUENCY
FOLDBACK
AT LOW VCAP
1.5
0
–45 –20
6
ILOAD = 1mA
–1.0
–45
5
1200
400
2.0
TJ (°C)
3110 G13
1400
2.5
Feedback Voltage vs Temperature
1.0
ILOAD = 1mA
0
3.0
3110 G11
Feedback Voltage vs VCAP
0.5
SWITCH B, C
SWITCH A, D
3.5
0.5
3110 G10
1.0
4.0
VOLTAGE CHANGE (%)
2
RDS(ON) (mΩ)
RDS(ON) (mΩ)
RDS(ON) of SWC
105
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
1.5
SWITCH LEAKAGE (µA)
RDS(ON) of SWB
105
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
1.5
TA = 25°C unless otherwise noted
1000
800
600
400
200
FREQUENCY
FOLDBACK
AT LOW VSYS
VCAP = 3.3V
VCAP = 1.8V
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
VSYS (V)
3110 G17
0.5
0
–0.5
–1.0
–45
5
55
105
155
TJ (°C)
3110 G18
3110fa
6
For more information www.linear.com/LTC3110
LTC3110
TYPICAL PERFORMANCE CHARACTERISTICS
VPROG Programming Voltage
vs Temperature
VPROG Programming Voltage
vs Temperature
0.7
0.8
0.5
THERMAL CHARGE
CURRENT FOLDBACK
0.4
0.3
0.2
0.1
0.6
0.6
0.5
0.4
0.2
VPROG (V)
VPROG CHANGE FROM 25°C (%)
0.6
0
–0.2
–0.4
5
30
55 80
TJ (°C)
5
–20
55
30
TJ (°C)
80
105
VPROG Programming Voltage
vs VCAP
0.3
0.2
0.1
0
0.4
0.3
0.2
0.4
0.6 0.8 1.0
VFBVCAP (V)
0.1
0
1
2
3
VCAP (V)
4
–0.5
5
–0.5
FALLING
RISING
1.7
2.6
–1.0
–45
5.3
4.4
3.5
–5
75
35
VSYS (V)
155
3110 G24
3110 G23
FBVCAP Comparator Thresholds
vs Temperature
115
TJ (°C)
3110 G22
IVSYS Input Current Limit
vs RPROG
DIR Thresholds vs Temperature
1.0
1.4
0
–0.4
0
1.2
0.5
–0.3
–0.4
1.0
2000
0.8
1750
0.4
0.2
0
–0.2
–0.4
–0.6
FALLING
RISING
–1.0
–45 –25 –5 15 35 55 75 95 115 135 155
TJ (°C)
3110 G25
0.5
1500
1250
IVSYS (mA)
CHANGE FROM 25°C (%)
0.6
–0.8
0.2
1.0
RPROG = 6.04k
–0.2
–0.3
0
CMPIN Threshold Voltage
vs Temperature
–0.1
–0.2
END OF
CHARGE
3110 G21
CHAGNE FROM 25°C (%)
CHANGE IN VPROG FROM VSYS = 3.3V (%)
CHANGE IN VPROG FROM VCAP = 1.8V (%)
0.5
–0.1
VFBVCAP CHANGE FROM 25°C (%)
130
VPROG Programming Voltage
vs VSYS
RPROG = 6.04k
0.4
0
3110 G20
3110 G19
0.5
0.3
0.1
–1.0
–45
105 130 155
CHARGE CURRENT
FOLDBACK
AT END OF CHARGE
0.4
0.2
–0.6
–0.8
0
–45 –20
–0.5
VPROG Programming Voltage
vs VFBVCAP
1.0
0.7
VPROG (V)
TA = 25°C unless otherwise noted
0
1000
–0.5
–1.0
–45
750
500
FALLING
RISING
–5
35
75
115
155
TJ (°C)
3110 G26
250
0
0
2
4
6
8 10 12 14 16 18 20 22 24
RPROG (kΩ)
3110 G27
3110fa
For more information www.linear.com/LTC3110
7
LTC3110
TYPICAL PERFORMANCE CHARACTERISTICS
PROG Current Gain
vs Temperature
IVSYS Input Current vs VCAP
RPROG = 3.01k
RPROG = 6.04k
0.50
RPROG = 12.4k
0
1.0
2.0
3.0
VCAP (V)
4.0
0.5
0
–0.5
–1.0
–2.0
–45
5.0
–15
15
45
3
2
1
RPROG = 6.04k
RPROG = 3.01k
RPROG = 1.50k
–1.5
75
105
0
135
1
0
2
TJ (°C)
3
VCAP (V)
4
5
3110 G29
3110 G28
VMID Load Regulation
3001 G30
VMID Buffer Current vs VCAP
1.0
VMID vs Temperature
1.0
400
VCAP = 2.5V
NO LOAD
300
VMID = VCAP
200
VCAP = 5V
0
VOLTAGE CHANGE (%)
0.5
IVMID (mA)
VOLTAGE CHANGE (%)
RPROG = 1.50k
RPROG = 3.01k
RPROG = 6.04k
RPROG = 12.4k
4
1.0
CURRENT (A)
IVSYS (A)
1.50
1
IVCAP Charge Current vs VCAP
1.5
RPROG = 1.50k
2.00
0
5
2.0
CHANGE FROM 25°C (%)
2.50
TA = 25°C unless otherwise noted
100
0
–100
–0.5
–200
VMID = PGND
0.5
VCAP = 5.5V
0
VCAP = 2.6V
–0.5
–300
–1.0
–0.3
–0.2
–0.1
0
0.1
IMID (A)
0.2
0.3
–400
0
1
2
3
5
6
–1.0
–45
–5
155
3110 G33
Backup Soft-Start
Backup Time
RUN
5V/DIV
VSYS
2V/DIV
VSYS
1V/DIV
0.50
115
TJ (°C)
3110 G32
Input Current Limit Aging
1.00
75
35
VCAP (V)
3110 G31
CHANGE FROM T = 0 YEAR (%)
4
ILOAD =
2A 1A
0.5A
0.25A
0V
0V
0
–0.50
–1.00
ACCELERATED LOAD LIFE
TEST DATA SCALED TO
TJ = 105°C, IVSYS = 2A
CONDITIONS
0
5
10
15
20
TIME (YEAR)
25
VCAP
2V/DIV
IL
0.2A/DIV
0A
0V
200µs/DIV
3110 G35
C1 = C2 = 2.4F
2s/DIV
3110 G45
30
3110 G34
3110fa
8
For more information www.linear.com/LTC3110
LTC3110
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C unless otherwise noted
Charge Sleep to Backup Transient
in Autonomous Application
Load Step 0A to 2A
BACKUP
VSYS
1V/DIV
VSYS
200mV/DIV
ILOAD
1A/DIV
CHRGB
5V/DIV
0V
VSYS
1V/DIV
CHRGB
5V/DIV
0V
IL
1A/DIV
0A
IL
1A/DIV
3110 G37
200µs/DIV
Burst Mode Operation
3110 G38
PWM Mode Operation in VCAP
Overvoltage Failure Condition
SW1
1V/DIV
SW1
5V/DIV
IL
0.2A/DIV
0A
IL
0.5A/DIV
SW2
5V/DIV
IL
100mA/DIV
0A
SW2
1V/DIV
0A
10ms/DIV
3110 G40
500ns/DIV
3110 G41
FBVCAP = 1.2V
VDIR = 0V
Charge Balancer Operation
C1 < C2
VCAP
VMID
2V/DIV
0V
3110 G42
500ns/DIV
ISYS = 100mA
Charge Balancer Operation
C1 > C2
3110 G39
200µs/DIV
PWM Mode Operation
VSYS
50mV/DIV
CHARGING
0A
0A
100µs/DIV
Backup to Charge Transient in
Autonomous Application
Single Capacitor Backup
VCAP
VMID
2V/DIV
ILOAD = 300mA
C1 = 1.2F
VSYS
1V/DIV
0V
0V
0A
0A
VCAP
1V/DIV
ISYS
1A/DIV
ISYS
1A/DIV
1s/DIV
3110 G43
0V
1s/DIV
3110 G44
500ms/DIV
3110 G36
3110fa
For more information www.linear.com/LTC3110
9
LTC3110
PIN FUNCTIONS
(FE/UFD)
CAPOK (Pin 1/Pin 22): VCAP Voltage OK Indicator Output.
The open-drain output is pulled low if the FBVCAP voltage
is lower than the FBVCAP falling threshold. The output is
released if FBVCAP is higher than the rising threshold.
CMPOUT (Pin 2/Pin 23): General Purpose Comparator Output. The open-drain output is pulled low while
the CMPIN pin voltage is above the comparator rising
threshold. The output is released when CMPIN is below
the falling threshold.
MODE (Pin 3/Pin 24): Burst/PWM Mode Selection Input.
Driving MODE to a logic 1 state programs fixed frequency,
low noise PWM operation. Driving MODE low programs
Burst Mode operation. Note that the MODE pin has no
effect when operating in charger mode.
CMPIN (Pin 4/Pin 1): General Purpose Comparator
Positive Input with Hysteresis. The voltage at CMPIN is
compared to an internal reference voltage. The pin can be
driven digitally or configured as voltage supervisor with
the help of an external resistor divider. If driven from a
resistor divider or from a source with >200Ω impedance,
connect a 0.1µF capacitor between CMPIN and GND for
best performance. The CMPIN rising threshold is 0.65V
and the falling threshold is 0.59V.
FBVCAP (Pin 5/Pin 2): VCAP End-Of-Charge Voltage Programming Feedback Divider Input with Hysteresis. The
end-of-charge threshold can be adjusted from 1.1V to
5.5V. The FBVCAP rising threshold is 1.095V and falling
threshold is 1.061V.
SGND (Pin 6/Pin 3): Signal Ground Connection. A ground
plane is highly recommended. Sensitive analog compo-
nents terminated at ground should connect to the SGND
pin with a Kelvin connection, separated from the high
current path in PGND.
DIR (Pin 7/Pin 4): Charge/Backup Mode Selector Input with
Hysteresis. A voltage on DIR above the rising threshold
enables the LTC3110 charger mode. A voltage below the
falling threshold enables the backup mode. The pin can
be driven digitally, e.g., from a µC. With the help of an
external resistor divider the pin can be configured as voltage supervisor input monitoring any system voltage. The
DIR rising threshold is 1.095V and the falling threshold
is 1.045V.
RUN (Pin 8/Pin 5): Logic-Controlled Shutdown Input.
RUN ≥ 1.0V: Normal Operation
RUN ≤ 0.3V: Shutdown
FB (Pin 9/Pin 6): VSYS Backup Voltage Feedback Pin.
Connect resistor divider tap here. The VSYS voltage can
be adjusted from 1.8V to 5.25V. The feedback reference
voltage is 0.6V.
PROG (Pin 10/Pin 7): Charger Input Current (IVSYS)
Programming Resistor. A resistor from PROG to SGND
programs the average current flowing in VSYS when operating in charging mode.
RPROG =
3kΩ •A
for 1.5kΩ <RPROG < 24.3kΩ
IVSYS
RPROG can be increased to 48.7k if the charge current foldback is avoided with FBVCAP held down < 1V or grounded.
3110fa
10
For more information www.linear.com/LTC3110
LTC3110
PIN FUNCTIONS
(FE/UFD)
CHRG (Pin 11/Pin 8): Charge/Backup Mode Indicator
Output. The open-drain output is pulled low while the
regulator is in charge mode. The open-drain output is
released while the regulator is in backup mode.
SVSYS (Pin 12/Pin 9): Signal Supply Voltage Input for
Buck/Boost Controller Circuitry. Pin must be shorted to
VSYS or supplied from VSYS through a RC filter. See the
Applications Information section for details.
VSYS (Pins 13, 15/Pins 10, 12): Bidirectional Power Supply
Pin for System Backup Output Voltage and Charge Current Input Voltage. A bypass capacitor must be connected
between VSYS and PGND. Refer to the Typical Applications
schematics and the Applications Information section for
capacitor selection details.
RSEN (Pin 14/Pin 11): Current Sense Resistor Tap at Junction of Internal Sense Resistor and Switch D. Pin RSEN
is internally shorted to pin VSYS via low impedance. DC
current in RSEN must be limited to 1.6A.
SW2 (Pins 16, 17/Pin 13, 14): Switch Pin Connected to
Internal Switches C and D of the Buck-Boost Regulator.
Connect one side of the buck-boost inductor to SW2.
Provide a short wide PCB trace from the inductor to SW2
to minimize voltage transients and noise.
PGND (Pins 18, 19, Exposed Pad Pin 25/Pins 15, 16,
Exposed Pad Pin 25): Power Ground Connection. Terminate all high current ground paths to PGND. The exposed
pad must be soldered to the PCB ground for rated thermal
performance.
SW1 (Pins 20, 21/Pins 17, 18): Switch Pin Connected to
Internal Switches A and B of the Buck-Boost Regulator.
Connect one side of the buck-boost inductor to SW1.
Provide a short wide PCB trace from the inductor to SW1
to minimize voltage transients and noise.
VCAP (Pins 22, 23/Pins 19, 20): Bidirectional Power Pin
for Connection to Supercap Backup Capacitor(s) or Backup
Battery(ies). When in charge mode a current flows out of
pin VCAP to charge the storage elements connected between VCAP and PGND. When in backup mode the current
is flowing into pin VCAP and the stored energy is used to
backup the load on VSYS.
VMID (Pin 24/Pin 21): Active Voltage Balancing Power
Output. This pin should be tied to the junction of two series
supercapacitors. If the output is not used, a compensation
capacitor of 1nF must be connected between pins VMID
and PGND.
3110fa
For more information www.linear.com/LTC3110
11
LTC3110
BLOCK DIAGRAM
CCAP
1µF
VOLTAGE
BALANCING
VMID
VCAP
SW1
A
BUF
D
C2
10F
B
+ –
R1
END OF CHARGE
CSYS
47µF
SVSYS
OVERCHARGE
THRESHOLD
CAPOK
+
–
BUCK-BOOST
CONTROL
CHARGER
+
–
ENABLE
VREF(PROG)
+
–
CMPIN
CCMPIN
0.1µF
VTH(CMP)
+
–
UNDERVOLTAGE
LOCKOUT
CMPOUT
CAPLOW
EN
RRUN
HIGH = ENABLE
LOW = SHUTDOWN
RUN
DIR
VSYS
VTH(DIR)
HIGH = CHARGING
LOW = BACKUP
RCHRG
CHARGING/BACKUP
EN
COMP
BACKUP
R4
+ –
CHRG
VCAP
+
–
VSYS
LOCKOUT
THRESHOLD
+
–
+
–
RCAPLOW
RPROG
OSC
RMODE
MODE
R3
PROG
COMP
ENABLE
VSYS
VSYS
1.8V TO 5.25V
2A
VSYS
CHARGER
INPUT
CURRENT
SENSE
VTH(CHRG)
RUN
HIGH = FORCED PWM
LOW = Burst Mode
OPERATION
VSYS
FBVCAP
END OF CHARGE
THRESHOLD
RCAPOK
C
+ –
R2
VSYS
RSEN
SW2
+
–
C1
10F
RSVSYS
51.1Ω
CSVSYS
RSEN 220nF
L1
1.5µH
VCAP
0.1V TO 5.5V
FB
R6
VREF(FB)
TEMP
SHUTDOWN
VREF AND
BIAS
VREFOK
R5
EN
SGND
PGND
3110 BD
3110fa
12
For more information www.linear.com/LTC3110
LTC3110
OPERATION
INTRODUCTION
Charging
The LTC3110 is a monolithic buck-boost DC/DC regulator/
charger combination with pin-selectable operation modes
to utilize a single LTC3110 device for charging (VDIR =
high) as well as for system backup (VDIR = low). During
charging a limit for the average current drawn from the
system power source can be accurately programmed with
an external resistor. An integrated, active, voltage balancing
buffer at pin VMID prevents capacitor overvoltage conditions caused from capacitor mismatch while charging a
stack of supercapacitors.
When powered from the system voltage, VSYS, the buckboost regulator is usually set to operate in charge mode
(VDIR = high), that is, a voltage source connected to VSYS
is the power input into the LTC3110 and the converter
charges a backup storage element connected between the
VCAP and PGND pins. When operating in charge mode, the
LTC3110’s average current limit circuitry is active. With a
resistor between the PROG and SGND pins, the maximum
average current drawn from VSYS can be programmed to
accurately limit the current demand.
The buck-boost regulator utilizes a proprietary switching
algorithm which allows the system voltage, VSYS, to be
regulated above, below, or equal to the voltage on the
storage element, VCAP, without discontinuity in inductor
current or large voltage ripple in the backup voltage VSYS.
With the DIR pin direction control circuitry, the LTC3110
can instantly reverse the inductor current and change
between charging and backup operation modes, reacting quickly on a power failure condition by providing the
backup voltage to the system (see Figure 1).
VCAP
VMID
2V/DIV
0A
ISYS
1A/DIV
1SECOND/DIV
3110 F02
Figure 2. Charge Foldback and Charge Termination
Active Charge Balancer
VSYS
1V/DIV
CHRG
5V/DIV
IL
1A/DIV
0A
200µs/DIV
3110 F01
Figure 1. Transition from Charge– into Backup Operation
The LTC3110 has been optimized to reduce quiescent
current in shutdown and standby for applications that
are sensitive to quiescent current drawn from the system
voltage, VSYS, or the storage element, VCAP. In charge
operation the standby current is only 40µA. In backup/
Burst Mode operation, the no-load standby current is only
40μA. In shutdown the total supply current is reduced to
less than 1μA.
While charging, the integrated linear charge balancing buffer regulates the mid-voltage, VMID, of a stack of capacitors
to half of VCAP thus equalizing out voltage mismatches of
top and bottom capacitor, see Figure 3. If the capacitor
mismatch is exceeding the current capabilities of the charge
balancer, charging is suspended until VMID comes back
to half of VCAP (see charging waveforms in the Typical
Performance Characteristics section). Note, the suspend
charge function is only active for VCAP > 2.2V = VTH(CHRG)
with hysteresis. For VCAP < 2V the charger operation is
always continuous.
3110fa
For more information www.linear.com/LTC3110
13
LTC3110
OPERATION
LTC3110
C1
VMID
VOLTAGE
BALANCING
that can be delivered by the converter, reduces VSYS
voltage ripple, and yields a low noise fixed-frequency
switching spectrum. A proprietary switching algorithm
provides seamless transitions between operating modes
and eliminates discontinuities in the average inductor current, inductor current ripple, and loop transfer function
throughout all regions of operation. These advantages
result in increased efficiency, improved loop stability, and
lower VSYS voltage ripple in comparison to the traditional
4-switch buck-boost converter.
VCAP
R
BUF
C2
R
+ –
+ –
WINDOW
COMPARATOR
1 = ALLOW CHARGING
0 = SUSPEND CHARGING
3110 F03
Figure 3. Active Charge Balancer
Charge Termination
The final charge voltage at pin VCAP is programmed with a
resistor divider at FBVCAP, see Figure 10 in the Application
Information Section.
If FBVCAP exceeds typically 95% of its end of charge
threshold, the PROG reference voltage and with it the
charge current level begins to fold back (see Figure 2).
Before charge termination the charge current is eventually
folded back to a level of typically 30% of the programmed
value (see charging waveforms in the Typical Performance
Characteristic section). When the programmed voltage
level is reached, the controller will terminate charging
and switch off into a low quiescent current state wherein
the charge balancer at the VMID pin is disabled and the
CAPOK pin is released. The low current state is maintained
until the voltage on VCAP decays and the FBVCAP falling
threshold is crossed. After this, controller and charge
balancer will resume operation with the CAPOK pin pulled
low until the regulation voltage is reached again. Note the
IC cannot prevent outside sources leaking current into
the capacitors from overvoltaging them.
Figure 4 shows the topology of the LTC3110 power stage
which is comprised of two P-channel MOSFET switches
and two N-channel MOSFET switches and their associated
gate drivers. In response to the error amplifier output, an
internal pulse-width modulator generates the appropriate switch duty cycles to maintain regulation of the VSYS
voltage.
When the VCAP voltage is significantly greater than the VSYS
voltage, the buck-boost converter operates in buck mode.
Switch D turns on continuously and switch C remains off.
Switches A and B are pulse-width modulated to produce the
required duty cycle to support the VSYS regulation voltage.
As the VCAP voltage decreases, switch A remains on for a
larger portion of the switching cycle. When the duty cycle
reaches approximately 90%, the switch pair AC begins
turning on for a small fraction of the switching period.
As the VSYS voltage decreases further, the AC switch pair
remains on for longer durations and the duration of the
BD phase decreases proportionally. At this point, switch
A remains on continuously while switch pair CD is pulsewidth modulated to obtain the desired VSYS voltage. At
this point, the converter is operating solely in boost mode.
L
VCAP
A
VSYS
D
B
Backup Operation in Fixed Frequency PWM Mode
With the MODE pin held high while VDIR = low, the LTC3110
operates in a fixed-frequency pulse-width modulation
(PWM) mode using a voltage mode control loop. This
mode of operation maximizes the VSYS backup current
SW2
SW1
C
LTC3110
3110 F04
Figure 4. Buck-Boost Switch Topology
3110fa
14
For more information www.linear.com/LTC3110
LTC3110
OPERATION
Backup in Burst Mode Operation
Reverse Current Limit (Backup Mode)
When MODE is held low while VDIR = low, the buck-boost
converter operates in Burst Mode operation using a variable frequency switching algorithm that minimizes the
no-load input quiescent current and improves efficiency
at light load by reducing the amount of switching to the
minimum level required to support the load. The VSYS
current capability in Burst Mode operation is substantially
lower than in PWM mode and is intended to support light
stand-by loads. Curves showing the maximum Burst Mode
load current as a function of the VCAP and VSYS voltage
can be found in the Typical Performance Characteristics
section of this data sheet. If the converter load in Burst
Mode operation exceeds the maximum Burst Mode current
capability, VSYS will lose regulation. Each Burst Mode cycle
is initiated when switches A and C turn on producing a
linearly increasing current through the inductor. When the
inductor current reaches the Burst Mode peak current limit,
switches A and C are turned off and switches B and D are
turned on, discharging the energy stored in the inductor
into the VSYS capacitor and load. Once the inductor current
reaches zero, all switches are turned off and the cycle is
complete. Current pulses generated in this manner are
repeated as often as necessary to maintain regulation of
the VSYS voltage.
In PWM mode operation the LTC3110 has the ability to
actively conduct current away from VSYS if it is necessary
to maintain regulation. If VSYS is held above the regulation voltage, it could result in large reverse currents. This
situation can occur if VSYS of the LTC3110 is held up by
another supply. To prevent damage to the part in this
condition, the LTC3110 has a reverse current comparator
that monitors the current entering power switch D from
the load. If this current exceeds 1.2A (typical), switch D
is turned off for the remainder of the switching cycle. For
a no-load current application, the inductor current ripple
must be lower than double the minimum reverse current
limit (1A • 2 = 2A maximum inductor current ripple). See
the Inductor Selection section for information about how
to calculate the inductor current ripple.
VCAP Peak and DC-Current Limits (Backup Mode)
The LTC3110 has two current limit circuits that are designed to limit the peak inductor current to ensure that
the switch currents remain within the capabilities of the
IC during output short-circuit or overload conditions.
First current limit: In PWM mode the VCAP DC current
limit operates by injecting a current into the feedback pin
(FB). For this current limit feature being most effective,
the Thevenin resistance (RBOT//RTOP) from FB to ground
should exceed 100kΩ.
On a hard VSYS short, with Burst Mode operation or
PWM mode selected, it is possible for the inductor current to increase substantially beyond the DC current limit
threshold. In this case the peak current, second current
limit, turns off the power switch until the start of the next
switching cycle.
Preventing VCAP Overcharge Failure Due to Reverse
DC Current(Backup Mode)
If during PWM backup operation (MODE = high and
DIR = low), an external power supply or any second DC/DC
regulator wrongly drives VSYS higher than the programmed
back-up voltage level, the LTC3110 will reverse its VSYS
current and simultaneously create reverse current flow
charging VCAP. If the wrong VSYS voltage level is kept for
a longer period of time, FBVAP may exceed the overcharge
threshold and the LTC3110 stops reverse charging.
Charging through reverse DC current while VDIR is low is
not indicated at pin CHRG, which remains high impedance.
The overcharge condition is generally prevented in the
application by setting the LTC3110 into charge operation,
if VSYS is driven from an external source.
If the external source is supervised from the DIR comparator, the CHRG output can drive the gate of a PMOS
and isolate the external source in backup operation, see
applications with PFET on pages 29, 20, 31.
If VSYS is supervised from the DIR comparator, the external source must be capable to deliver more than the
maximum reverse current limit of the LTC3110 in backup
direction, see autonomous application on page 36. Only
if the external supply is strong enough, charge operation
can be initiated reliably.
3110fa
For more information www.linear.com/LTC3110
15
LTC3110
OPERATION
FBVCAP Failure Condition
RSEN Current Sense Resistor Tap
External component failures, e. g., open or shorted resistors or leakage currents at pin FBVCAP, can cause VCAP to
charge up to a higher, undefined voltage. If VCAP exceeds
typically 5.95V, the LTC3110 suspends charging which
protects the LTC3110 from substantially exceeding the
absolute maximum ratings if FBVCAP is shorted to ground.
RSEN connects to the junction of FET D and the integrated
sense resistor.
Note supercapacitors and batteries often have a lower
maximum voltage rating than 5.95V. In these cases the
general purpose comparator can be configured to detect
the overvoltage at VCAP (see the figure General Purpose
Comparator as redundant VCAP supervisor in the Application Information section).
Soft-Start (Backup Mode)
To minimize VCAP current transients on power-up, the
LTC3110 incorporates an internal soft-start circuit. The
soft-start is implemented by a linearly increasing ramp
of the error amplifier reference voltage during the softstart duration. During the soft-start period the regulator
is always operating in PWM operation independent of the
MODE pin setting. In case the VSYS voltage at start-up is
already pre-charged above 80% of the target value, the
soft-start is skipped and the LTC3110 immediately enters
the mode of operation that has been set with the MODE
pin. The soft-start period is reset by thermal shutdown
and from undervoltage lockout events.
Error Amplifier and Internal Compensation of VSYS
Backup Voltage Regulation
The buck-boost converter utilizes a voltage mode error
amplifier with an internal compensation network.
Error Amplifier and Internal Compensation of VSYS
Average Current Limit Regulation
The buck-boost converter in charge mode (DIR = high)
utilizes an error amplifier with an internal compensation
network to regulate the average current flowing into the
VSYS pin. The current limit is programmable with RPROG.
The RSEN pin can be left unconnected, otherwise a load
current, IRSEN, will simultaneously decrease the average
charge current flowing out of the VCAP pin. Note: A fast
voltage step at VSYS in the presence of a large RSEN capacitor causes a large inrush current through the internal RSEN
resistor, e. g., closure of a mechanical power connection
supplying VSYS. In these cases, the value of the capacitor
between RSEN and ground is limited to a maximum of 10µF.
VCAPOK End-Of-Charge Indicator and FBVCAP
Comparator
The LTC3110 includes an open-drain comparator output
pin, VCAPOK, which is used to indicate the charging state
of the energy storage element.
The comparator input, FBVCAP, is typically connected
with a resistor divider from VCAP to ground in order to
program the final charge voltage. When FBVCAP exceeds
the rising threshold, the comparator output, VCAPOK, is
high impedance. When FBVCAP drops below the falling
threshold, VCAPOK is pulled to ground. While RUN = high,
CAPOK continues to pull down with reduced strength until
both VCAP and VSYS are below the threshold of the internal
pull-down transistor, maximum 1.4V.
The comparator operates in both charge and backup mode
and is unconditionally released if the LTC3110 is shut
down with RUN = low.
CHRG Operation Mode Indicator and DIR Comparator
The LTC3110 includes an open-drain DIR comparator
output pin, CHRG, which is typically used to indicate
the operation mode of the chip: charge or backup. With
the help of a pull-up resistor the output can be used to
interface with a microcontroller, or connect to the gate
of a p-channel MOSFET used as an input isolation switch
(see USB application in the Typical Application section).
The DIR comparator has hysteresis and the CHRG pin is
pulled low while VDIR is greater than the comparator rising
threshold and CHRG is released while VDIR is lower than
its falling threshold.
3110fa
16
For more information www.linear.com/LTC3110
LTC3110
OPERATION
CMPIN
CMPOUT
LTC3110
VTH(CMP)
+
–
EN
3110 F08
Figure 5. General Purpose Comparator
The CHRG pin is unconditionally released if the LTC3110
is shut down with RUN = low or in undervoltage condition.
Note that the DIR pin can be driven above VCAP or VSYS,
as long as the voltage is limited to less than the absolute
maximum rating.
General Purpose Comparator
The LTC3110 includes a voltage comparator with its input accessible at the CMPIN pin and with a fixed internal
reference voltage.
The comparator can be used to monitor VCAP, VSYS or any
auxiliary supply voltage. The open-drain output, CMPOUT,
can interface to a microcontroller with the help of a pull-up
resistor. The comparator is typically used to supervise VCAP
and to set a threshold for the lowest VCAP voltage tolerated in backup mode before the system needs to reduce
power consumption. The CMPOUT pin is unconditionally
released if the LTC3110 is shut down with RUN = low
or in undervoltage condition (see also the Applications
Information section).
Shutdown
Shutdown of the LTC3110 is accomplished by pulling the
RUN pin below 0.3V and IC operation is enabled by pulling the RUN pin above 1.0V. The RUN pin has an internal
pull-down resistor. Note that RUN can be driven above
VCAP or VSYS, as long as the voltage is limited to less than
the absolute maximum rating.
Thermal Foldback of Charge Current
To help preventing the LTC3110 from going into thermal shutdown when charging very large capacitors, the
LTC3110 is equipped with a thermal regulator. If the die
temperature exceeds 130°C (typical) the average VSYS
current limit is lowered to help reduce the amount of
power being dissipated in the package. The current limit
is reduced to approximately 15% of the programmed
limit just before thermal shutdown. The current limit will
return to its full value when the die temperature drops
below 130°C, typically.
Undervoltage Lockout
If either voltages at VCAP and VSYS drop below the undervoltage lockout falling threshold, the LTC3110 will stop
operation and the SW1, SW2, VMID, CMPOUT, CHRG and
PROG pins will be high impedance. CAPOK will continue
to pull down with reduced strength until both VCAP and
VSYS are below the threshold of the internal pull-down
transistor, maximum 1.4V. The LTC3110 will resume
operation when at least one pin, VCAP or VSYS, rises above
the undervoltage lockout rising threshold.
THERMAL CONSIDERATIONS
The power switches in the LTC3110 are designed to operate continuously with currents up to the internal current
limit thresholds. However, when operating at high current
levels there may be significant heat generated within the
IC. As a result, careful consideration must be given to
the thermal environment of the IC in order to optimize
efficiency and ensure that the LTC3110 is able to provide
its full-rated output current. Specifically, the exposed pad
of both the QFN and TSSOP packages shall be soldered
to the PC board and the PC board should be designed to
maximize the conduction of heat out of the IC package.
If the die temperature exceeds approximately 165°C,
the IC will enter overtemperature shutdown, all switching will be inhibited and the charge balancer disabled.
Note: Open-drain output pins CAPOK, CMPOUT and CHRG
may still pull down while in thermal shutdown. The part will
remain disabled until the die cools by approximately 10°C.
The soft-start circuit is reinitialized in overtemperature
shutdown to provide a smooth recovery when the fault
condition is removed.
3110fa
For more information www.linear.com/LTC3110
17
LTC3110
APPLICATIONS INFORMATION
The standard LTC3110 application circuit is shown as the
Typical Application on the front page of this data sheet.
The appropriate selection of external components is dependent upon the required performance of the IC in each
particular application given considerations and trade-offs
such as PCB area, cost, VSYS and VCAP voltage, allowable
ripple voltage, efficiency and thermal considerations. This
section of the data sheet provides some basic guidelines
and considerations to aid in the selection of external components and the design of the application circuit.
Inductor Selection
The choice of inductor used in LTC3110 application circuits
influences the maximum deliverable backup and charge
current, the magnitude of the inductor current ripple,
and the power conversion efficiency. The inductor must
have low DC series resistance or current capability and
efficiency will be compromised. Larger inductance values
reduce inductor current ripple and will therefore generally
yield greater backup current capability. For a fixed DC
resistance, a larger value of inductance will yield higher
efficiency by reducing the peak current to be closer to
the average backup current and therefore minimize resistive losses due to high RMS currents. However, a larger
inductor within any given inductor family will generally
have a greater series resistance, thereby counteracting
this efficiency advantage. An inductor used in LTC3110
applications should have a saturation current rating that is
greater than the worst-case average inductor current plus
half the ripple current. The peak-to-peak inductor current
ripple for each operational mode can be calculated from
the following formula:
∆IL(P-P)(BUCK) =
VSYS  VCAP – VSYS 

1.2MHz •L 
VCAP
∆IL(P-P)(BOOST) =
VCAP  VSYS – VCAP 

1.2MHz •L 
VSYS
L is the inductance in μH.
In addition to its influence on power conversion efficiency,
the inductor DC resistance can also impact the maximum
output capability of the buck-boost converter particularly
at low VCAP voltages. In buck mode, the output current of
the buck-boost converter is limited only by the inductor
current reaching the current limit threshold. However, in
boost mode, especially at large step-up ratios, the VSYS
backup current capability can also be limited by the total
resistive losses in the power stage. These include switch
resistances, inductor resistance and PCB trace resistance.
Use of an inductor with high DC resistance can degrade
the VSYS backup current capability from that shown in the
Typical Performance Characteristics section of this data
sheet. As a guideline, in most applications the inductor DC
resistance should be significantly smaller than the typical
power switch resistance of 60mΩ.
The minimum inductor value must guarantee that the
worst-case average VCAP current plus half the ripple current doesn’t reach the VCAP current limit threshold. For the
fixed switching frequency of 1.2MHz the recommended
typical inductor value is 1.5µH.
Different inductor core materials and styles have an impact
on the size and price of an inductor at any given current
rating. Shielded construction is generally preferred as it
minimizes the chances of interference with other circuitry.
The choice of inductor style depends upon the price, sizing,
and EMI requirements of a particular application. Table 1
provides a small sampling of inductors that are well suited
to many LTC3110 applications.
Table 1. Recommended Inductors
VENDOR
Coilcraft
www.coilcraft.com
Würth Elektronik
www.we-online.com
Coiltronics www.
cooperindustries.com
Vishay
www.vishay.com
Sumida
www.sumida.com
Murata
www.murata.com
Taiyo Yuden
www.t-yuden.com
TDK
www.component.tdk.com
PART/STYLE
XAL50xx Series (XAL5030-222ME_)
XAL60xx Series (XAL6030-222ME_)
EPL7040 Series (EPL7040-222ME_)
WE-HCI Series (744310150,
744314200) WE-LHMI Series
(74437346018, 74437349022)
DR73 Series (DR73-2R2-R) DRQ74
Series (DR74-2R2-R)
IHLP-2525 Series (IHLP-2525AH-01,
IHLP-2525CZ-01) IHLP-2020 Series
(IHLP-2020CZ-A1)
CDEP6D31ME Series (CDEP6D31MENP2R2MC)
LQH66S Series (LQH66SN1R5M03)
NR6012T2R5NE NR8040T2R0N
CLF Series
3110fa
18
For more information www.linear.com/LTC3110
LTC3110
APPLICATIONS INFORMATION
VSYS Capacitor Selection
A low ESR capacitor should be utilized at the VSYS pin in
order to minimize VSYS backup voltage ripple. Multilayer
ceramic capacitors are an excellent option as they have
low ESR and are available in small footprints. The capacitor
value should be chosen large enough to reduce the VSYS
voltage ripple to acceptable levels. Neglecting the capacitor
ESR and ESL, the peak-to-peak VSYS voltage ripple can
be calculated by the following formulas, where CVSYS is
the VSYS capacitance and ILOAD is the VSYS load current.
∆VP-P(BUCK) =
VSYS
8 • (1.2MHz ) •L •C VSYS
∆VP-P(BOOST) =
2
 VCAP – VSYS 


V
CAP
 VSYS – VCAP 
ILOAD

1.2MHz •C VSYS 
VSYS
Given the VSYS current is discontinuous in boost mode, the
ripple in this mode will generally be much larger than the
magnitude of the ripple in buck mode. In addition to VSYS
voltage ripple generated across the VSYS capacitance, there
is also VSYS voltage ripple produced across the internal
resistance of the VSYS capacitor. The ESR-generated VSYS
voltage ripple is proportional to the series resistance of
the VSYS capacitor.
Supercapacitor Selection and Additional Bypass
The LTC3110 is stable with a total CVCAP capacitance value
greater than 2mF, or 4mF for each stacked capacitor. Supercapacitors are much larger physically than ceramic or
tantalum capacitors, and therefore usually cannot be placed
close to the charger. To minimize layout contribution to
capacitor ESR, the trace width connecting the capacitors
to each other and the IC should be as large as possible.
The VMID pin trace is not as critical, as it only carries
300mA of average current. It is recommended that a local decoupling capacitor be placed from VCAP to ground,
and the capacitor should be placed as close to the IC as
possible. Multilayer ceramic capacitors are an excellent
choice for voltage decoupling as they have extremely low
ESR and are available in small footprints. While a 10μF
decoupling capacitor is sufficient for most applications,
larger values may be used without limitation.
To minimize voltage ripple and ensure proper operation of
the IC, a low ESR bypass capacitor with a value of 100nF
and a second low ESR bypass capacitor of 10μF should
be located as close to the VCAP pin as possible. The traces
connecting this capacitor to VCAP and the ground plane
should be made as short as possible. If using a single VSYS
capacitor where balancing is not required, a capacitor of at
least 100nF must be connected between VMID and PGND.
Recommended VCAP and VSYS Bypass Capacitors
The choice of capacitor technology is primarily dictated
by a trade-off between cost, size and leakage current.
Ceramic capacitors are often utilized in switching converter applications due to their small size, low ESR and
low leakage currents. However, many ceramic capacitors
designed for power applications experience significant
loss in capacitance from their rated value with increased
DC bias voltages. For example, it is not uncommon for
a small surface mount ceramic capacitor to lose more
than 50% of its rated capacitance when operated near
its rated voltage. As a result, it is sometimes necessary
to use a larger value capacitance or a capacitor with a
higher voltage rating than required in order to actually
realize the intended capacitance at the full operating voltage. To ensure that the intended capacitance is realized
in the application circuit, be sure to consult the capacitor
vendor’s curve of capacitance versus DC bias voltage. The
capacitors listed in Table 3 provide a sampling of small
surface mount ceramic capacitors that are well suited to
LTC3110 application circuits. All listed capacitors are either
X5R or X7R dielectric in order to ensure that capacitance
loss over temperature is minimized.
Maximum Capacitor Voltage and Balancing
The service lifetime of a supercapacitor is determined
by its rated voltage, rated temperature, rated lifetime,
actual operating voltage, and operating temperature. To
extend the life of a supercapacitor the operating voltage
and temperature should be reduced from the maximum
ratings. The websites for Illinois Capacitor1 and Maxwell2
provide the means to determine their capacitor lifetime.
1http://www.illinoiscapacitor.com/tech-center/life-calculators.aspx
2http://www.maxwell.com/products/ultracapacitors/docs/
APPLICATIONNOTE1012839_1.PDF
3110fa
For more information www.linear.com/LTC3110
19
LTC3110
APPLICATIONS INFORMATION
Using the suggested derated voltage for each capacitor will
improve lifetime. The LTC3110 will keep each capacitor
voltage at VCAP/2 once VCAP is higher than typically 2.2V.
To prevent an overvoltage on one of the supercapacitors
during charging, the VMID voltage is continuously driven
from the voltage balancing buffer output with typically
300mA of current capability.
The LTC3110 has minimal current draw from VCAP at end
of charge. Care should be taken to limit sources of current
that may pull VCAP above its programmed regulation value,
as there is no way for the LTC3110 to maintain regulation.
VSYS Voltage Programming
The VSYS voltage is set via an external resistor divider
connected to the FB pin as shown in Figure 6.
VCAP Voltage Programming
The VCAP voltage is set via an external resistor divider
connected to the FBVCAP pin as shown in Figure 7.
The resistor divider values determine the maximum VCAP
voltage according to the following formula:
 R

VCAP = 1.095V •  1+ TOP 
 RBOT 
Care should be taken to limit sources of current that may
pull VCAP above its programmed maximum value, as there
is no way for the LTC3110 to maintain VCAP regulation
in charger mode (see also Figure 15, Overvoltage Error
Signal Provided to the µC).
C1
The resistor divider values determine the VSYS backup
voltage according to the following formula:
VCAP
1µF
RTOP
LTC3110
FBVCAP
SGND
C2
RBOT
 R

VSYS = 0.6V •  1+ TOP 
 R

3110 F10
(1)
BOT
The buck-boost converter utilizes voltage mode control and
in addition to setting the VSYS voltage, the value of RTOP
plays an integral role in the dynamics of the feedback loop.
In general, a larger value for RTOP will increase stability
and reduce the speed of the transient response. A smaller
value of RTOP will reduce stability but increase the speed of
the transient response. A good starting point is to choose
RTOP = 1M and then calculate the required value of RBOT
to set the desired VSYS voltage according to Equation 1.
If a large VSYS capacitor is used, the bandwidth of the
converter is reduced. In such cases RTOP can be reduced
to improve the transient response. If a large inductor or
small VSYS capacitor is utilized the loop will be less stable
and the phase margin can be improved by increasing the
value of RTOP.
VSYS
VMID Charge Balancer Output
This pin should be tied to the junction of two series supercapacitors. A push/pull buffer output forces the VMID
pin to half of the voltage of the VCAP pin. Generally capacitors with equal value of at least 1nF should be connected
from VCAP to VMID and from VMID to PGND if the output is
unused, e.g., for applications with a single supercapacitor
or batteries.
1µF
C1
VCAP
LTC3110
VMID
C2
3110 F11
Figure 8. VMID Charge Balancer Output
RTOP
LTC3110
Figure 7. VCAP Voltage Programming
FB
SGND
RBOT
3110 F09
Figure 6. Setting the VSYS Backup Voltage
20
For more information www.linear.com/LTC3110
3110fa
LTC3110
APPLICATIONS INFORMATION
SINGLE
CAPACITOR
OR BATTERY
1µF


R TOP
VTH(DIR _ RISING) = 1.095V •  1+
 RBOT +RMID 
VCAP
1nF
LTC3110
VMID
1nF
3110 F12
Figure 9. Charge Balancer Unused with Single Capacitor
DIR Backup Supervisor Threshold Voltage
Programming
The backup supervisor threshold voltage is set via an external resistor divider connected to the DIR pin as shown
in Figure 10.
The resistor divider values determine the DIR supervisor
threshold voltage according to the following formula:
 R

VTH(DIR _ RISING) = 1.095V •  1+ TOP 
 RBOT 
 R

VTH(DIR _ FALLING) = 1.045V •  1+ TOP 
 RBOT 


R TOP
VTH(DIR _ FALLING) = 1.045V •  1+
 RBOT +RMID 
 R
+R 
VSYS = 0.6V •  1+ TOP MID 
RBOT


Note the direction supervisor threshold VTH(DIR_RISING)
must be higher and have enough voltage difference to
the backup voltage VSYS to accommodate for the resistor
tolerances, ripple voltage and voltage dipping from load
current steps. If necessary an RC filter in front of the DIR
pin may reduce the reaction speed of the supervisor, see
Figure 12.
Pay attention to the requirement, if the DIR input supervises
VSYS as in Figure 11 or in the autonomous applications on
page 36, the external VSYS supply must be capable to deliver
more than the maximum reverse current limit of 2A of the
LTC3110, in order to reliably change into charge operation.
BACKUP
VOLTAGE
SUPERVISED
VOLTAGE
LTC3110
RTOP
VSYS
DIR
SGND
RTOP
DIR
RMID
LTC3110
RBOT
FB
PGND
3110 F13
SGND
RBOT
3110 F14
Figure 10. Setting the DIR Back-Up Supervisor
Threshold Voltage
Figure 11. Voltage with Reduced Tolerances
Programming Backup Voltage and DIR Threshold
Voltage with Improved Accuracy
In applications with the DIR pin voltage and the FB pin
voltage divided down from the same VSYS voltage, a single
resistor divider string is reducing the effect of resistor
tolerances and saves one resistor component:
SUPERVISED
VOLTAGE
RTOP
DIR
LTC3110
PGND
CDIR
SGND
RBOT
3110 F15
Figure 12. Filtering DIR voltage
3110fa
For more information www.linear.com/LTC3110
21
LTC3110
APPLICATIONS INFORMATION
IVSYS Average Current Limit Programming for Charger
Operation (DIR = High)
The VSYS average current limit is set via an external resistor connected between the PROG pin and signal ground,
SGND, as shown in Figure 13.
The resistor value determines the average current into
VSYS according to the following formula:
IVSYS =
3kΩ
RPROG
For applications with a wide temperature range, the thermal
coefficient of resistor RPROG must be taken into account.
If RPROG is > 12.4k, additional RFLT and CFLT are required
for filtering.
If CMPIN is driven from a resistor divider or from any output
with >200Ω impdance, connect a 0.1uF capacitor between
CMPIN and GND for best performance, see figure 14) .
General Purpose Comparator Configuration as
Redundant VCAP Supervisor for Overvoltage Failure
Detection
Component failures interrupting the VCAP voltage feedback
(FBVCAP) can potentially cause an over voltage condition
at VCAP during charging. The general purpose comparator
can be configured as the supervisor providing an overvoltage error signal to the microcontroller (see Figure 15).
C1
RTOP
C2
CCMPIN
0.1µF
RBOT
PROG
LTC3110
RPROG
LTC3110
CMPIN
CMPOUT
10k
µC
ERR
RUN
CFLT
10nF (OPT)
3110 F18
RFLT
6.04k (OPT)
SGND
VDD
VCAP
Figure 15. Overvoltage Error Signal Provided to the µC
3110 F16
Figure 13. Setting the VSYS Average Current Limit
CMPIN Configuration as General Purpose Voltage
Supervisor with Hysteresis
The resistor divider values, see Figure 14, determine rising
and falling threshold VTH according to the following formula:
SVSYS Filtering
In many noise critical applications it is useful to filter the
signal supply pin, SVSYS, with a small RC filter on the
PCB, see Figure 16. Note, if the filter is added any further
loads connected to the SVSYS pin must be checked if they
are small with respect to the resistor impedance and not
creating undesired voltage drops at SVSYS.
 R

VTH(RISING) = 0.65V •  1+ TOP 
 RBOT 
CSYS
 R

VTH(FALLING) = 0.59V •  1+ TOP 
 RBOT 
VSYS
OUT
CSVSYS
220nF
SGND
RTOP
RBOT
SVSYS
LTC3110
VTH
VDD
RSVSYS
51.1Ω
3110 F19
CCMPIN
0.1µF
CMPIN
Figure 16. SVSYS Filtering
LTC3110
RUN, DIR, MODE, CMPIN Inputs Digitally Controlled
CMPOUT
3110 F17
Figure 14. General Purpose Voltage Supervisor
The RUN, DIR, MODE and CMPIN comparator inputs can
be driven digitally from an external microcontroller.
3110fa
22
For more information www.linear.com/LTC3110
LTC3110
APPLICATIONS INFORMATION
VDD
RUN
DIR
LTC3110
MODE
CHRG
LTC3110
CAPOK
µC
µC
CMPOUT
CMPIN
SGND
SGND
3110 F21
3110 F20
Figure 17. Inputs RUN, DIR, MODE, CMPIN Driven from a
Microcontroller
Open-Collector Outputs
CHRG, CAPOK and CMPOUT open-collector outputs can
be connected together with other external signals in wired
OR configuration and pull-up resistors for level shifting
when interfacing into µC Inputs.
Figure 18. Outputs CHRG, CAPOK, CMPOUT Interfacing to µC
The open-collector outputs can also be used to drive small
loads up to 20mA, e.g., miniature lamps or LEDs.
Table 2: Recommended Supercapacitors and Ultracapacitors
VALUE
(F)
ESR
(mΩ)
VOLTAGE
(V)
TEMPERATURE
RANGE (°C)
Murata Electronics
DMF3R5R5L334M3DTA0
DMF3Z5R5H474M3DTA0
0.33
0.47
60
40
4.2 (5.5 Peak)
4.2 (5.5 Peak)
–30 to 70
–30 to 70
14.0 × 21.0 × 2.5
14.0 × 21.0 × 3.2
Tecate
TPL-10/10X30F
TPL-25/16X26F
TPL-100/22X45F
TPLE-25/16X26F
TPLE-100/22X45F
TPLS-400/35X60F
10
25
100
25
100
400
85
42
15
42
15
12
2.7
2.7
2.7
2.3
2.3
2.7
–40 to 65
–40 to 65
–40 to 65
–40 to 85
–40 to 85
–40 to 65
10.0 × 10.0 × 30.0
16.0 × 16.0 × 26.0
22.0 × 22.0 × 45.0
16.0 × 16.0 × 26.0
22.0 × 22.0 × 45.0
35.0 × 35.0 × 60.0
AVX
BZ015A503Z_B
BZ015A104Z_B
0.05
0.1
160
80
5.5
5.5
–20 to 70
–20 to 70
28.0 × 17.0 × 4.1
28.0 × 17.0 × 6.7
CAP-XX
HS206F
HS230
0.6
1.2
70
50
5.5
5.5
–40 to 85
–40 to 85
39.0 × 17.0 × 2.5
39.0 × 17.0 × 3.8
Cooper Bussmann
A1635-2R5475-R
M1325-2R5905-R
HB1625-2R5256-R
HV1860-2R7107-R
4.7
9
25
100
25
20
36
10
2.5
2.5
2.5
2.7
–25 to 70
–40 to 60
–25 to 70
–40 to 65
16.0 × 16.0 × 35.0
13.0 × 13.0 × 26.0
16.0 × 16.0 × 25.0
18.0 × 18.0 × 60.0
Illinois Capacitor
506DER2R5SLZ
357DER2R5SEZ
50
100
30
12
2.5
2.5
–40 to 70
–40 to 70
18.0 × 18.0 × 60.0
35.0 × 35.0 × 60.0
Maxwell
BCAP0005
BCAP0100T01
5
100
170
15
2.7
2.7
–40 to 65
–40 to 65
10.0 × 10.0 × 20.0
22.0 × 22.0 × 45.0
Taiyo Yuden
PAS2026FR2R5504
PAS0815LS2R5105
LIC2540R3R8207
0.5
1
200
55
70
50
2.5
2.5
2.2 to 3.8
–25 to 60
–25 to 70
–25 to 70
26.0 × 20.0 × 0.9
8.0 × 8.0 × 15.0
25.0 × 25.0 × 40.0
VENDOR
SIZE (mm) W × L × H
3110fa
For more information www.linear.com/LTC3110
23
LTC3110
APPLICATIONS INFORMATION
PCB Layout Considerations
Table 3. Representative Bypass and VSYS Capacitors
PART NUMBER
VALUE (µF) VOLTAGE (V) FOOTPRINT
AVX
12066D106K
12066D226K
12066D476K
10
22
47
6.3
6.3
6.3
0603
0805
0805
Kemet
C0603C106M9PACTU
C0805C226M9PACTU
C0805C476M9PACTU
10
22
47
6.3
6.3
6.3
0603
0805
0805
Murata
GRM188D70J106MA73
GRM219B30J226ME47
GRM21BB30J476ME15
10
22
47
6.3
6.3
6.3
0603
0805
0805
TDK
C1608X7S0J106M080AC
C2012X5R0J226M085AB
C2012X5R0J476M125AC
10
22
47
6.3
6.3
6.3
0603
0805
0805
Taiyo Yuden
JMK107BJ106MA
JMK212ABJ226MD
JMK212BBJ476MG
10
22
47
6.3
6.3
6.3
0603
0805
0805
The LTC3110 switches large currents at high frequencies.
Special care should be given to the PCB layout to ensure
stable, noise-free operation. Figures 19 and 20 depict the
recommended PCB layout to be utilized for the LTC3110,
if a 2-layer PCB is being used. A 4-layer PCB layout is
recommended for thermal and noise reasons. A few key
guidelines follow:
1. All circulating high current paths should be kept as
short as possible. This can be accomplished keeping the
routes to the components in Figures 19 and 20 as short
and as wide as possible. Capacitor ground connections
should be connect by vias down to the ground plane
in the shortest route possible. The bypass capacitors
CSYS and CCAP should be placed as close to the IC as
possible and should have the shortest possible path to
ground.
2. The components shown and their connections should
all be placed over a complete ground plane.
3. Use of vias in the die attach pad will enhance the thermal environment of the charger, especially if the vias
extend to a ground plane region on the exposed bottom
surface of the PCB.
4. Keep the connections to the FB, PROG, DIR, CMPIN
and FBVCAP pins as short as possible and away from
the switch pin connections.
3110fa
24
For more information www.linear.com/LTC3110
LTC3110
APPLICATIONS INFORMATION
BOTTOM COPPER LAYER
C2
TOP LAYER
CCAP
C1
1
24
2
23
3
22
4
21
LTC3110
5
20
6
19
7
18
8
17
9
16
10
15
11
14
12
13
CSYS
L1
COMPONENT NAMES:
SEE TYPICAL APPLICATION
ON PAGE 27
VIA TO GROUND PLANE
3110 F22
Figure 19. PCB Component Placement of the TSSOP Package
3110fa
For more information www.linear.com/LTC3110
25
LTC3110
APPLICATIONS INFORMATION
BOTTOM COPPER LAYER
COMPONENT NAMES:
SEE TYPICAL APPLICATION
ON PAGE 27
C2
TOP LAYER
CCAP
1
19
20
21
22
23
24
C1
18
LTC3110
14
6
13
L1
12
5
11
15
10
16
4
7
3
7
17
7
2
CSYS
VIA TO GROUND PLANE
3110 F23
Figure 20. PCB Component Placement of the QFN Package
3110fa
26
For more information www.linear.com/LTC3110
LTC3110
TYPICAL APPLICATIONS
3.3V/2A Output from Stack of Supercapacitors Backup/Recharge Application with Active Voltage Balancing
MAIN
STEP-DOWN DC/DC
FB
12V
BUS
CSVSYS
220nF
L1
1.5µH
C1
10F
R1
1910k
C2
10F
R3
1910k
CCAP
1µF
SW2 SVSYS
FBVCAP
R2
523k
VSYS
CMPIN
VMID
VSYS
3.25V
2A
CSYS
47µF
RSEN
PROG
CCMPIN
0.1µF
R4
523k
VCAP SW1
RSVSYS
51.1Ω
12V BUS
SUPERVISOR
R5
976k
LTC3110
MODE
RPROG
6.04k
FB
R6
221k
1000k
DIR
DIR
CHRG
CAPOK
CMPOUT
RUN
SGND
1000k
µC
CAPOK
CAPLOW
AT VCAP = 2.8V
PGND
3110 TA02
1.8V/300mA Output from Single Capacitor Discharged from 2.5V to 1V and with Reserve Available Down to 0.3V
MAIN
STEP-DOWN DC/DC
FB
12V
BUS
VSYS = 1.9V CHARGING
CSVSYS
220nF
L1
1.5µH
C1
10F
R1
2000k
R3
1300k
R4
1870k
CCAP
1µF
VCAP SW1
SW2 SVSYS
FBVCAP
R2
1580k
VSYS
RSEN
PROG
CCMPIN
0.1µF
CMPIN
CMID1
1nF
CMID2
1nF
VMID
VSYS
1.83V BACKUP
300mA
CSYS
47µF
LTC3110
MODE
SGND
12V BUS
SUPERVISOR
R5
976k
FB
DIR
CHRG
CAPOK
CMPOUT
RUN
RPROG
6.04k
PGND
R6
475k
1000k
1000k
DIR
µC
CAPOK
CAPLOW
3110 TA03
3110fa
For more information www.linear.com/LTC3110
27
LTC3110
TYPICAL APPLICATIONS
500mA USB Charge/Backup Application with Variable Charging Power, PCHRG, Depending on System Load
USB
PUSB UP TO 5V • 500mA
M1
IRLML6402
R7
7.50k
R8
2.49k
5V
CSVSYS
220nF
ROFF
3.3k
L1
1.5µH
PCHRG = PUSB – PSYS
C1
10F
R1
1910k
C2
10F
R3
1910k
CCAP
1µF
R4
1270k
SW2 SVSYS
VCAP SW1
FBVCAP
R2
511k
RSVSYS
51.1Ω
CSYS
330µF
VSYS
RSEN
PROG
CCMPIN
0.1µF
RPROG
6.04k
R5
976k
FB
R6
133k
VMID
DIR
CHRG
CAPOK
CMPOUT
RUN
SGND
CFB
10pF
1000k
1000k
CDIR
1nF
MODE
µC
USB
DATA
END OF CHRG
CAPLOW
3110 TA04
PGND
USB Connect Transition
BACKUP
1.2V, 1A
CMPIN
LTC3110
1V/DIV
PSYS
5V, 0.1A
2.5V, 0.1A
1.8V, 0.2A
SYSTEM
DC/DC
REGULATORS
USB Disconnect Transition
CHARGING
CHARGING
BACKUP
1V/DIV
VSYS
CHRG
5V/DIV
CHRG
5V/DIV
VSYS
DISCONNECT
VUSB
VUSB
ILI
2A/DIV
ILI
2A/DIV
100µs/DIV
3110 TA04b
100µs/DIV
3110 TA04c
3110fa
28
For more information www.linear.com/LTC3110
LTC3110
TYPICAL APPLICATIONS
Autonomous Backup and Recharge Application with Input Isolation Switch
CSVSYS
220nF
L1
2.2µH
C1
100F
R1
1910k
C2
100F
R3
1910k
R4
681k
CCAP
1µF
VCAP SW1
SW2 SVSYS
FBVCAP
R2
536k
RSVSYS
51.1Ω
BACK-UP
3.2V
VSYS
CSYS
150µF
ROFF
3.3k
RSEN
PROG
CCMPIN
0.1µF
M1
IRLML6402
CMPIN
FB
LTC3110
VMID
DIR
MODE
SGND
0V
IL
1A/DIV
0A
CHRGB
2V/DIV
0V
FB MAIN
STEP-DOWN
DC/DC
R5
931k
R6
215k
3.6V/3.21V
2.5V
1.8V
SYSTEM
DC/DC
REGULATORS
1.2V
R7
9.31k
R8
4.53k
1000k
1000k
3110 TA08
CHRG
CAPOK
CAPLOW
PGND
CHARGE SLEEP
1V/DIV
CMAIN
47µF
12V BUS
1.5A
RPROG
3.01k
CHRG
CAPOK
CMPOUT
RUN
VMAIN
CHARGING
3.6V ±4%
BACKUP
VSYS
VMAIN
500µs/DIV
3110 TA06b
3110fa
For more information www.linear.com/LTC3110
29
LTC3110
TYPICAL APPLICATIONS
Lead Acid Battery Backup/Recharge Application
12V
3.3V LDO OR
BUCK
REGULATOR
M1
IRLML6402
3.6V
47µF
R7
9.31k
R8
4.53k
3.21V/
3.6V
L1
1.5µH
ROFF
10k
+
BATT
4V 2.5Ah
R1
976k
R3
1910k
R4
604k
CMID1
1nF
CMID2
1nF
CCAP
1µF
SW2 SVSYS
VCAP SW1
FBVCAP
R2
316k
VSYS
1.2V
RSEN
PROG
CCMPIN
0.1µF
CSYS
150µF
2.5V
1.8V
SYSTEM
DC/DC
REGULATORS
RPROG
6.04k
CMPIN
LTC3110
FB
VMID
R5
976k
R6
226k
1000k
1000k
DIR
MODE
CHRG
CAPOK
CMPOUT
RUN
SGND
END OF CHRG
BATTLOW
PGND
3110 TA05
3110fa
30
For more information www.linear.com/LTC3110
LTC3110
TYPICAL APPLICATIONS
NiMH Battery Backup/Recharge Application
CSVSYS
220nF
L1
1.5µH
NiMH
1.2V
3700mAh
×3
+
CCAP
1µF
VCAP SW1
SW2 SVSYS
FBVCAP
VSYS
PROG
CCMPIN
0.1µF
CMPIN
CMID1
1nF
CMID2
1nF
VMID
VSYS
3.25V
2A
CSYS
47µF
RSEN
R3
1910k
R4
604k
RSVSYS
51.1Ω
LTC3110
MODE
RPROG
12.4k
RFAST
8.06k
FB
R6
221k
DIR
CHRG
CAPOK
CMPOUT
RUN
SGND
VSYS
SUPERVISOR
R5
976k
PGND
1000k
DIR
VCC
BATTLOW
FASTCHRG
µC
RUN
FBVCAP
ADIN
RTEMP
3110 TA06
NOTE ON DIGITAL CONTROL SIGNALS IN NiMH BACKUP/RECHARGE APPLICATION:
CHARGING IS INITIATED BY PULLING DIR = HIGH AND FBVCAP = LOW.
CHARGING IS TERMINATED BY PULLING DIR = HIGH AND FBVCAP = HIGH (FBVCAP MUST BE ≥ 1.2V).
SYSTEM BACK-UP IS INITIATED BY FORCING FBVCAP = LOW, WAITING 5µs, THEN FORCING DIR = LOW.
GENERAL SAFETY NOTE: CHARGING MUST BE TERMINATED IF THE BATTERY VOLTAGE
OR CHARGE TIME HAVE REACHED THEIR MAXIMUM VALUES OR IF THE BATTERY
TEMPERATURE IS ABOVE OR BELOW THE SAVE OPERATING REGION OF THE BATTERY,
SEE DATASHEET OF THE BATTERY.
THE THERMISTOR, USED FOR MEASURING THE TEMPERATURE, MUST HAVE GOOD
THERMAL CONNECTION TO THE BATTERY PACK.
3110fa
For more information www.linear.com/LTC3110
31
LTC3110
TYPICAL APPLICATIONS
R11
348Ω
ISOLAR
+ D1
SOLAR CELL
–
24h/7d Active Solar Powered Sensor/Transmitter Supply
Q1
PBSS302
VSOLAR
PRIMARY
BATTERY
LITH 3V, 1Ah
OPTIONAL
D1 SCHOTTKY
OPTIONAL
C1
100F
MODULE
6V, 150mA
~12 CELLS
CSVSYS
220nF
L1
2.2µH
R1
1910k
C2
100F
CCAP
47µF
FBVCAP
R2
511k
SUPERCAPS
SW2 SVSYS
VCAP SW1
VSYS
PROG
CCMPIN
0.1µF
LTC3110
FB
S1
S2
PFO
GND
RUN
RST
SGND
PGND
DAY 1
DAY 2
DAY 3
DAY 4
ISOLAR
20mA/DIV
VCAP
2V/DIV
VSYS
2V/DIV
MODE = LOW
ISYS = 0.5mA
8h/DIV
CHRG
CAPOK
CMPOUT
M2
2N7002
32
VSOLAR
5V/DIV
0V
ISOLAR
100mA/DIV
0A
VSYS
AC COUPLED
100mV/DIV
IVCAP
1A/DIV
0A
3110 TA09b
R9
1000k
3110 TA09
Charging States
PRE
CHARGING
CHARGING
VCAP = 4V
5ms/DIV
CHARGING WITH SOLAR CURRENT AND 24/7 BACKUP:
IF DAYLIGHT IS PRESENT, THE SUPERCAPACITORS ARE CHARGED UP WITH THE OUTPUT
CURRENT OF THE SOLAR CELLS. WHEN DAYLIGHT IS NOT PRESENT, THE SUPERCAPS
PARTIALLY DISCHARGE AND PROVIDE THE BACKUP POWER TO MAINTAIN VSYS.
HIGH BACKUP POWER MODE (NO WAVEFORM): IF MODE = HIGH AND WITH THE
SUPERCAPACITORS CHARGED, THE APPLICATION CAN PROVIDE THE VSYS BACKUP VOLTAGE
WITH LOW RIPPLE AND FULL OUTPUT CURRENT CAPABILITIES. MODE = HIGH STOPS
FURTHER CHARGING.
CHARGING STATES:
IF MODE = LOW: THE VSYS VOLTAGE IS FED WITH CURRENT FROM THE SOLAR MODULE OR
IS REGULATED FROM THE LTC3110 IN BURST MODE IF SUNLIGHT IS MISSING. IF SUNLIGHT
IS PRESENT, VSYS IS REGULATED WITH A TWO POINT VOLTAGE REGULATION DEFINED BY
DIR RISING AND DIR FALLING THRESHOLDS.
THE APPLICATION HAS THREE STATES OF OPERATION:
1. C SYS PRE-CHARGING STATE: THE SOLAR PANEL OUTPUT CURRENT PRE-CHARGES THE
CAPACITOR CSYS UNTIL THE DIR VOLTAGE RISES ABOVE THE DIR RISING THRESHOLD
AND THE SUPERCAPACITOR CHARGING STATE IS ENTERED.
2. SUPERCAPACITOR CHARGING STATE: THE LTC3110 CHARGES THE SUPERCAPACITORS
BY DRAWING CURRENT FROM CAPACITOR CSYS UNTIL THE VSYS VOLTAGE FALLS BELOW
THE DIR FALLING THRESHOLD AND THE VSYS PRE-CHARGING STATE IS RE-ENTERED.
THE LTC3110 TOGGLES BETWEEN THE PRE-CHARGING STATE AND THE CHARGING STATE
UNTIL FBVCAP IS ABOVE THE FBVCAP RISING THRESHOLD AND THE CHARGE SLEEP STATE
IS ENTERED.
SENSOR
R8
422k
M1
2N7002
Charging with Solar Current and 24/7 Backup
DISPLAY
R10
1000k
R7
953k
MODE
LTC2935-2
TRANSMITTER
GSM
R6
221k
DIR
VCC
2A
PULSE
HIGH
BACKUP
END OF
POWER
CHARGE CAPLOW MODE
R5
976k
CMPIN
CSYS3
4700µF
<30mΩ
MICRO CONTROLLER
RPROG
3.01k
VMID
S0
CSYS2
4700µF
<30mΩ
CSYS1
47µF
RSEN
R3
1910k
R4
523k
3.25V LOW RIPPLE HIGH BACKUP POWER MODE, MODE = HIGH
3.42V/3.58V SOLAR CHARGING, MODE = LOW
ISYS
VSYS =
RSVSYS
51.1Ω
3110 TA09C
3. CHARGE SLEEP STATE (NO WAVEFORM): VCAP IS FULLY CHARGED AND FBVCAP IS ABOVE
THE FBVCAP FALLING THRESHOLD WHILE THE VSYS VOLTAGE IS REGULATED WITH
LTC3110’s BURST MODE BACKUP OPERATION. IN THE CHARGE SLEEP STATE, THE SOLAR
MODULE IS ISOLATED FROM VSYS.
STARTUP WITH DISCHARGED SUPERCAPS:
THE VSYS VOLTAGE IS MONITORED WITH THE LTC2935-2 SUPERVISOR ENABLING THE
LTC3110 ONLY AT A VOLTAGE ABOVE 2.7V.
IF POWERED FROM HIGH IMPEDANCE SOURCES (E. G. SOLAR CELLS). V SYS MUST BE
INITIALLY HIGH ENOUGH TO SKIP THE SOFT START FUNCTION OF THE LTC3110, SEE SOFT
START (BACKUP MODE) IN THE OPERATION SECTION.
NOTES: THE REQUIRED PANEL SIZE AND THE NUMBER OF SOLAR CELLS IN SERIES OR IN
PARALLEL STRONGLY DEPENDS ON THE LOCAL SUNLIGHT CONDITIONS. VSOLAR MUST BE
ONE V BE HIGHER THAN VSYS (3.58V + 0.7V = 4.3V) IN THE LOWEST LIGHT CONDITION TO
DELIVER SOLAR CURRENT.
TO PREVENT OVERVOLTAGING OF V SYS, THE IVSYS AVERAGE CURRENT LIMIT MUST BE AT
LEAST FOUR TIMES LARGER THAN THE MAXIMUM SOLAR CURRENT (IVSYS_PROG > 4 ×
ISOLAR_MAX ). ALTERNATIVELY, OUTPUT CHRG CAN BE ADDITIONALLY CONNECTED TO THE
BASE OF Q1 TO ISOLATE THE SOLAR PANEL DURING CHARGING.
THE ABSOLUTE MAXIMUM OF VSOLAR IS DEFINED FROM THE VCEO VALUE OF Q1 (E.G. 20V)
WHICH ALLOWS THE CONNECTION OF MODULES WITH OPEN CIRCUIT VOLTAGES OF VOC > 5.25V.
OPTIONALLY A PRIMARY BATTERY CAN BE ADDED AS RESERVE TO COVER POOR LIGHT
CONDITIONS.
EXAMPLE SOLAR MODULE MANUFACTURERS:
SHARP, PANASONIC, POWERFILM
3110fa
For more information www.linear.com/LTC3110
LTC3110
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC3110#packaging for the most recent package drawings.
FE Package
24-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1771 Rev B)
Exposed Pad Variation AA
7.70 – 7.90*
(.303 – .311)
3.25
(.128)
3.25
(.128)
24 23 22 21 20 19 18 17 16 15 14 13
6.60 ±0.10
2.74
(.108)
4.50 ±0.10
6.40
2.74 (.252)
(.108) BSC
SEE NOTE 4
0.45 ±0.05
1.05 ±0.10
0.65 BSC
1 2 3 4 5 6 7 8 9 10 11 12
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.25
REF
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
1.20
(.047)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE24 (AA) TSSOP REV B 0910
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3110fa
For more information www.linear.com/LTC3110
33
LTC3110
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LTC3110#packaging for the most recent package drawings.
UF Package
24-Lead Plastic QFN (4mm × 4mm)
(Reference LTC DWG # 05-08-1697 Rev B)
0.70 ±0.05
4.50 ±0.05
2.45 ±0.05
3.10 ±0.05 (4 SIDES)
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
4.00 ±0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
R = 0.115
TYP
0.75 ±0.05
PIN 1 NOTCH
R = 0.20 TYP OR
0.35 × 45° CHAMFER
23 24
PIN 1
TOP MARK
(NOTE 6)
0.40 ±0.10
1
2
2.45 ±0.10
(4-SIDES)
(UF24) QFN 0105 REV B
0.200 REF
0.00 – 0.05
0.25 ±0.05
0.50 BSC
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3110fa
34
For more information www.linear.com/LTC3110
LTC3110
REVISION HISTORY
REV
DATE
DESCRIPTION
A
03/16
Add H-grade option.
PAGE NUMBER
Clarified conditions and Note 9 for Input Current Limit.
2, 4
4
Changed axis labels VMID Buffer Current, Backup Time, Charge Balancer curves.
8, 9
Enhanced 1.8V/300mA output circuit.
27
3110fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC3110
35
LTC3110
TYPICAL APPLICATION
Autonomous Backup and Recharge Application (3.6V Nominal, 3.2V Backup Voltage)
12V
BUS
FB
MAIN STEP-DOWN DC/DC
2A + ISYS = MINIMUM REQUIREMENT
CSVSYS
220nF
L1
2.2µH
C1
10F
R1
1910k
C2
10F
R3
1910k
CCAP
1µF
FBVCAP
R2
681k
VSYS
CMPIN
LTC3110
VMID
MODE
3.6V/3.21V
RPROG
6.04k
R5
1020k
2.5V
1.8V
SYSTEM
DC/DC
REGULATORS
1.2V
R6
200k
FB
R7
280k
1000k
1000k
1000k
DIR
CHRG
CAPOK
CMPOUT
RUN
NOTE: THE DRIVING CAPABILITY OF THE MAIN DC/DC SHOULD EXCEED THE MAXIMUM
REVERSE CURRENT LIMIT OF THE LTC3110 PLUS ISYS,THE LOAD CURRENT DEMANDED
FROM THE SYSTEM DC/DC REGULATORS CONNECTED AT VSYS.
CSYS
47µF
RSEN
PROG
CCMPIN
0.1µF
R4
715k
SW2 SVSYS
VCAP SW1
3.6V ±4%, 2A NOMINAL FROM MAIN DC/DC
3.21V, 1.5A BACKUP
RSVSYS
51.1Ω
CHRG
CAPOK
CAPLOW
3110 TA07
SGND
PGND
RELATED PARTS
PART NUMBER
LTC4040
DESCRIPTION
2.5A Battery Backup Power Manager
LTC3226
2-Cell Supercapacitor Charger with Backup
PowerPath™ Controller
LTC3625/LTC3625-1 1A High Efficiency 2-Cell Supercapacitor
Charger with Automatic Cell Balancing
LTC3128
LTC3350
3A Monolithic Buck-Boost Supercapacitor
Charger and Balancer with Accurate Input
Current Limit
High Current Supercapacitor Backup
Controller and System Monitor
COMMENTS
Step-Up Backup Supply and Step-Down Battery Charger, 6.5A Switches for 2.5A,
Automatic Seamless Switchover to Backup Mode Backup from 3.2V Battery
1×/2× Multimode Charge Pump Supercapacitor Charger with Automatic Cell
Balancing. Internal 2A LDO Backup Supply (CPO to VOUT). Automatic Main/Backup
Switchover, 3mm × 3mm QFN-16 Package
High Efficiency Step-Up/Step-Down Charging of Two Series Supercapacitors,
Automatic Cell Balancing. Programmable Charging Current Up to 500mA (Single
Inductor), 1A (Dual Inductor), 3mm × 4mm DFN-12 Package
±2% Accurate Average Input Current Limit Programmable to 3A, Active Charge
Balancing, Charges 1 or 2 Capacitors, VIN: 1.73V to 5.5V, VOUT: 1.8V to 5.5V
Synchronous Step-Down CC/CV Charging up to Four Series Supercapacitors
VIN: 4,5V to 35V, 14-Bit ADC for Monitoring System Voltages/Currents, Capacitance
and ESR, Internal Active Balancers, 38-Lead 5mm × 7mm QFN Package
LTC4425
Linear SuperCap Charger with CurrentConstant-Current/Constant-Voltage Linear Charger for 2-cell Series Supercapacitor
Limited Ideal Diode and V/I Monitor
Stack, 2A Charge Current, Auto Cell Balancing, 20μA Quiescent Current
LTC3127
1A Buck-Boost DC/DC Converter with
Programmable (0.2A to 1A) ±4% Accurate Average Input Current Limit,
Programmable Input Current Limit
1.8V to 5.5V (Input) and 1.8V to 5.25V (Output) Voltage Range
1.2A IOUT, 1.6MHz, Synchronous Boost DC/DC 94% Efficiency, VIN: 1.8V to 5.5V, VOUT(MAX) = 5.25V, IQ = 15μA,
LTC3125
Converter With Adjustable Input Current Limit ISD < 1μA, 2mm × 3mm DFN-8 Package
95% Efficiency, VIN: 2.4V to 5.5V, VOUT : 2.4V to 5.25V, IQ = 50µA,
LTC3441/LTC3441-2/ 1.2A IOUT, 2MHz, Synchronous Buck-Boost
DC/DC Converter
ISD < 1µA, 3mm × 4mm DFN-12 Package
LTC3441-3
LTC3113
3A Low Noise Buck-Boost DC/DC Converter 96% Efficiency, VIN: 1.8V to 5.5V, VOUT : 1.8V to 5.5V, IQ = 40µA,
ISD < 1µA, 4mm × 5mm DFN-16 and 20-Lead TSSOP Packages
LTC3355
20V 1A Buck DC/DC with Integrated SCAP
VIN Voltage Range: 3V to 20V, VOUT Voltage Range: 2.7V to 5V, 1A Current
Mode Buck Main Regulator, 5A Boost Backup Regulator Powered from Single
Charger and Backup Regulator
Supercapacitor Down to 0.5V, Overvoltage Protection
LTC3643
2A Bidirectional Power Backup Supply
Bidirectional Synchronous Boost Capacitor Charger/Buck Regulator for System
Backup, Wide VIN Voltage Range: 3V to 17V, Up to 40V Capacitor Voltage, 2A
Maximum CAP Charge Current, Low Profile 24-Lead 3mm × 5mm QFN Package
3110fa
36 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC3110
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC3110
LT 0316 REV A • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2015