tb504

Technical Brief 504
ISL70001SEH, ISL70001SRH VOUT Power-Up/Down
Glitch Problem Report
Abstract
This technical brief explains the GIDEP Problem Advisory BP6-P-16-01 issued for the ISL70001SEH, ISL70001SRH devices.
Table of Contents
Description of Problem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Summary of Simulation Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Discussion of Simulation Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Summary of Bench Testing Results Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Discussion of Bench Testing Results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ISL70001SEH, ISL70001SRH Implemented as Clock Slave or Externally Clocked Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
List of Figures
FIGURE 1.
FIGURE 2.
FIGURE 3.
FIGURE 4.
FIGURE 5.
FIGURE 6.
FIGURE 7.
FIGURE 8.
FIGURE 9.
FIGURE 10.
FIGURE 11.
FIGURE 12.
FIGURE 13.
FIGURE 14.
FIGURE 15.
FIGURE 16.
FIGURE 17.
FIGURE 18.
FIGURE 19.
FIGURE 20.
FIGURE 21.
FIGURE 22.
FIGURE 23.
April 21, 2016
TB504.0
VOUT Response During a Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
VOUT Power-Up/Down Anomalous Glitch Simulation Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Power-Up Simulations of Nominal Processing at Three Temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Power-Up Simulations of Process Corners 1 and 3 at +125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Power-Up Simulations of Process Corners 2 and 4 at +125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Simulations Close-Up View of Process Corners VOUT Glitch as Compared to 2x (VOUT = 2xVREF) the Soft-Start Voltage. . .8
Process Corner 4 Ramp Down at +150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Pre and Post 100krad(Si) Power-Up Ramp for Nominal Process at +25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
VOUT Simulation for Constant VIN = 1.796V to Produce a Steady-State Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power-Up Glitch for Unit LOT-3-1 at +25°C Prior to Irradiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power-Up Glitch for Unit LOT-3-1 at +25°C after Biased Irradiation to 100krad(Si) and 50-300rad(Si)/s . . . . . . . . . . . . . 13
Power-Down Glitch for Unit LOT-1-2684 at +25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power-Down Glitch for Unit LOT-3-1 at +25°C after Biased Irradiation to 100krad(Si) and 50-300rad(Si)/s . . . . . . . . . . 14
DC Behavior of Unit LOT-3-1 at +25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power-Up Glitch Magnitudes at +25°C Plotted by Product Lot Groupings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power-Down Glitch Magnitudes at +25°C Plotted by Product Lot Groupings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Anomalous DC VOUT Magnitudes at +25°C Plotted by Product Lot Groupings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power-Up Glitch Magnitudes at Temperatures +25°C, +85°C, and +125°C for Four Sampled Units . . . . . . . . . . . . . . . . 20
Power-Down Glitch Magnitudes at Temperatures +25°C, +85°C, and +125°C for Four Sampled Units . . . . . . . . . . . . . . 20
LOT-1-2684 Power-Down Glitch at +125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pre- and Post-Radiation (100krad(Si)) +25°C Power-Up Glitch Magnitudes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pre- and Post-Radiation (100krad(Si)) +25°C Power-Down Glitch Magnitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Slow PVIN Rise, Resulting in Early Master LX and SYNC Activity With No Clocked Slave LX Activity . . . . . . . . . . . . . . . . . . 22
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2016. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
Technical Brief 504
Description of Problem
The ISL70001SRH and ISL70001SEH can exhibit a VOUT
response during a power-up or power-down period when VIN is
between 1.3V and 1.8V. This range of VIN is below the nominal
VIN POR threshold of approximately 2.65V for PORSEL set to
ground and 4.1V for PORSEL set to VIN. For VIN ramps of faster
than 10V/ms this anomalous output activity is not possible,
however, for slower VIN ramps there is the possibility of output
activity. During power-up, VOUT follows a normal soft-start
behavior, which will not exceed the VOUT set-point voltage. During
power-down VIN ramp the activity again will not exceed the
set-point voltage. The size of the anomalous VOUT response is
inversely related to the ramp rate of VIN as this sets how long the
part is in the anomalous activity range. See Figure 1 for an
illustration of the issue. This problem has been fixed on the
ISL70001ASEH.
Regulator start-up at low
PVIN. No voltage stress on
LX and no excess inrush
current
Normal start-up after 2.8V is
crossed by PVIN.
is never exceeded as indicated by the DC VIN case at the bottom
of Table 1.
TABLE 1. SIMULATION RESULTS FOR POWER-UP/DOWN
ANOMALOUS VOUT GLITCH FOR VIN RAMPING BETWEEN
0V AND 2V AT 0.2V/ms.
SIMULATION CONDITIONS
(Note 1) VOUT GLITCH (V)
Power-up, Nominal Process, -55°C
Figure 3 0
Power-up, Nominal Process, +25°C
Figure 3 0.058
Power-up, Nominal Process, +125°C
(Worst temp)
Figure 3 0.236
Power-up, Process Corner 1, +125°C
Figure 4 0.103
Power-up, Process Corner 3, +125°C
Figure 4 0
Power-up, Process Corner 2, +125°C
Figure 5 0.368
Power-up, Process Corner 4, +125°C
(Worst case)
Figure 5 0.426
Power-down, Process Corner 4, +125°C
Figure 7 Discharges from
0.7V
Power-up, Post 100krad, Nominal process, Figure 8 0.236
+25°C
Inrush current at normal
start-up, much greater
than start-up at low PVIN
Normal start-up of VOUT
VOUT rise due to LX
pulsing, no overvoltage
FIGURE 1. VOUT RESPONSE DURING A POWER-UP
Summary of Simulation Results
Transistor level simulations indicate that the ISL70001SEH,
ISL70001SRH VOUT glitch during power-up and power-down is
limited by the soft-start voltage and ultimately by the selected
VOUT setting (e.g., 1.2V). The glitch is a normal soft-start event
terminated when POR lockout becomes active by 1.8V. That is,
the glitch will follow soft-start and not exceed the programmed
output voltage setting, even if the VIN stalls in the window of the
anomalous switching activity. In the ramped power-up situation,
the glitch is dominated by the soft-start voltage so the resulting
glitch is substantially smaller than the selected output voltage.
During power-down the soft-start voltage can cause the VOUT to
discharge if it is precharged to a non-zero value.
Discussion of Simulation Results
Simulations were run for the anomalous VOUT activity (glitch)
during power-up and power-down for 0V < VIN < 2V. Simulations
used the schematic shown in Figure 2 on page 4. Note that the
VIN ramp rate was set to 0.2V/ms for both power-up and
power-down. The results from the sequence of simulations run
are summarized in Table 1. The largest power-up glitch in a VOUT
of 426mV occurred for process corner 4 run at a temperature of
+125°C. This is well below the output set point of 1.2V. Slower
ramps will lead to larger glitches, however, the set-point voltage
Submit Document Feedback
2
DC VIN = 1.796V for Process Corner 4,
+125°C
Figure 9 1.178 for 1.200
set
NOTE:
1. Simulation plots are in the called out Figures.
The first three simulations of Table 1 are depicted in Figure 3 on
page 5. For the -55°C case the oscillator (SyncIO) never goes
active so that the switching node (Phase1) never activates and
consequently the output (VOUT) never charges. The fall of Dfeet
activates the POR circuitry and blocks further switching until POR
is released at about VIN = 2.65V (for PORSEL set to ground). The
+25°C case shows both SyncIO and Phase1 activity before Dfeet
goes low. This short activity results in a VOUT glitch of 58mV. At
+125°C the SyncIO and Phase1 activity starts at a lower VIN and
proceeds to allow VOUT to track the soft-start voltage (SS_cap)
with the selected feedback gain of 2x applied. In this case the
VOUT glitch reaches 236mV. The +125°C case is the worst
temperature for the glitch.
The four process corners were run at +125°C and are the next
four entries in Table 1. The 1st and 3rd process corners are
depicted in Figure 4 in the same fashion as in Figure 3. Corner 1
had a short episode of Phase1 activity that yielded an output
glitch of 103mV. Corner 3 exhibited no Phase1 activity and
consequently had no glitch on VOUT. Figure 5 depicts the results
from the 2nd and 4th process corners. Both cases resulted in
appreciable VOUT glitches of 368mV and 426mV respectively. So
the worst case power-up glitch of 426mV was seen for process
corner 4 and a temperature of +125°C.
Figure 6 on page 8 shows the four process cases of power-up
simulations at +125ºC comparing the VOUT signal to 2x the
soft-start voltage. The factor of 2 comes from the set-point
voltage being set to 1.2V and the reference voltage being 0.6V.
These plots highlight the fact that the soft-start voltage is in
control of the glitch ramp. This indicates that the voltage control
loop is functioning and in control of VOUT and that a normal
TB504.0
April 21, 2016
Technical Brief 504
soft-start has been initiated. This assertion is further supported
by simulation results in Figure 9 on page 11. This simulation
allows the anomalous switching condition to continue by holding
VIN = 1.796V. The resulting VOUT response ramps up to
approximately the set-point voltage of 1.200V (1.178V) and then
holds at that level. Again the voltage loop is seen to be active and
in control of VOUT.
Figure 8 on page 10 presents simulations to represent the
effects of radiation. The pre-radiation case shown (on the left) is
again the nominal process at +25°C. The post-radiation
(100krad(Si), on the right) is the process corner representing the
nominal process post-radiation at +25°C. The radiation has
increased the glitch from 58mV to 236mV, but the form of the
glitch in that it follows the soft-start voltage remains intact.
A power-down ramp was simulated for process corner 4 at
+150°C and the results are presented in Figure 7 on page 9. In
this case the VOUT was precharged to 0.7V to emulate the load
discharging VOUT to a diode drop indicative of an active load. The
most interesting fact is that the anomalous switching activity
leads to the VOUT being discharged.
Submit Document Feedback
3
TB504.0
April 21, 2016
Submit Document Feedback
4
Technical Brief 504
NOTE: For power-down simulation the output voltage was precharge to 0.7V based on system power-down
behaviors with real loads.
TB504.0
April 21, 2016
FIGURE 2. VOUT POWER-UP/DOWN ANOMALOUS GLITCH SIMULATION SCHEMATIC
Submit Document Feedback
5
Technical Brief 504
-55°C
+25°C
+125°C (PRODUCED WORST CASE VOUT GLITCH OF 236mV)
FIGURE 3. POWER-UP SIMULATIONS OF NOMINAL PROCESSING AT THREE TEMPERATURES
TB504.0
April 21, 2016
Submit Document Feedback
6
Technical Brief 504
NOTE: Only corner 1 generated a VOUT glitch at 103mV.
FIGURE 4. POWER-UP SIMULATIONS OF PROCESS CORNERS 1 AND 3 AT +125°C
TB504.0
April 21, 2016
Submit Document Feedback
7
FIGURE 5. POWER-UP SIMULATIONS OF PROCESS CORNERS 2 AND 4 AT +125°C
Technical Brief 504
NOTE: Corner 4 exhibited the worst case glitch Of 426mV.
TB504.0
April 21, 2016
Submit Document Feedback
8
Technical Brief 504
NOTE: These show that the glitch is limited by the soft-start voltage as
the part follows a normal soft-start progression.
FIGURE 6. SIMULATIONS CLOSE-UP VIEW OF PROCESS CORNERS VOUT GLITCH AS COMPARED TO 2x (VOUT = 2xVREF) THE SOFT-START VOLTAGE.
TB504.0
April 21, 2016
Submit Document Feedback
9
Technical Brief 504
NOTE: Starting from a precharge of 0.7V to emulate power-down ramps of actual loads. The switching
activity actually causes the VOUT to discharge under soft-start voltage control.
FIGURE 7. PROCESS CORNER 4 RAMP DOWN AT +150°C
TB504.0
April 21, 2016
Submit Document Feedback
10
Technical Brief 504
FIGURE 8. PRE AND POST 100krad(Si) POWER-UP RAMP FOR NOMINAL PROCESS AT +25°C
TB504.0
April 21, 2016
Submit Document Feedback
11
Technical Brief 504
NOTE: Conditions were process corner 4 and +125°C. VOUT stops rising at approximately the
set-point voltage of 1.200V (1.178V untrimmed).
FIGURE 9. VOUT SIMULATION FOR CONSTANT VIN = 1.796V TO PRODUCE A STEADY-STATE RESPONSE
TB504.0
April 21, 2016
Technical Brief 504
Summary of Bench Testing
Results Summary
Bench testing the ISL70001SEH, ISL70001SRH for the
anomalous VOUT response on power-up and power-down
demonstrated that the glitch never exceeded 1V when the set
voltage was 1.2V. This was true of all 40 units from five different
production lots tested at +25°C as well as for the four units
selected for testing at +125°C and the six units tested post
irradiation to 100krad(Si) at 50-300rad(Si)/s. The pertinent
parameters for the bench testing are listed in Table 2.
The worst power-up glitch for all testing conditions was 627mV
for irradiated LOT-3-1, which also registered the worst case
+25°C power-up glitch at 296mV. The pre- and post-irradiation
power-up glitches are presented in Figures 10 and 11
respectively. It should be noted that both responses follow
normal soft-start charging behavior until termination of the
anomalous switching at about VIN = 1.8V. In the post-irradiation
case, Figure 11, the VIN ramp barely extended beyond the
termination of the anomalous switching period leading to a
result indicative of a much slower power-up ramp than intended.
A faster ramp would have terminated the switching event sooner
and led to a smaller glitch.
TABLE 2. PERTINENT PARAMETERS FOR BENCH TESTING
ISL70001SEH, ISL70001SRH FOR POWER-UP AND
POWER-DOWN ANOMALOUS VOUT GLITCH.
PARAMETER
VALUE
Input Capacitance
200µF
Output Inductor
1µH
Output Capacitance
500µF
Soft-Start Capacitance
100nF
VREF Capacitance
220nF
Output Set Voltage
1.2V
Power-Up Supply Ramp
Between 0.1 and 0.2V/ms
Power-Down Supply Ramp
Between -0.1 and -0.2V/ms
VIN Sweep Limits
0V to 2V
NOTE: Testing was done on a socketed ISL70001SEH, ISL70001SRH
evaluation board.
Submit Document Feedback
12
TB504.0
April 21, 2016
Technical Brief 504
VIN
LX
VOUT
FIGURE 10. POWER-UP GLITCH FOR UNIT LOT-3-1 AT +25°C PRIOR TO IRRADIATION
VIN
LX
VOUT
FIGURE 11. POWER-UP GLITCH FOR UNIT LOT-3-1 AT +25°C AFTER BIASED IRRADIATION TO 100krad(Si) AND 50-300rad(Si)/S
Submit Document Feedback
13
TB504.0
April 21, 2016
Technical Brief 504
The worst case power-down glitch of 467mV was seen on unit
LOT-1-2684 at +25°C and is represented in Figure 12. The rapid
VOUT charging at the end of switching activity was anomalous
among the parts tested. The next worst power-down event was
registered by unit LOT-3-1 after irradiation and is shown in
Figure 13. The final discharge phase of the glitch was typical
behavior.
Units were also tested for the DC condition of VIN held at the top
of the region of anomalous switching. Of all the units tested in
this fashion, LOT-3-1 exhibited the highest VOUT level at 905mV
as is represented in Figure 14 on page 15.
VIN
LX
VOUT
FIGURE 12. POWER-DOWN GLITCH FOR UNIT LOT-1-2684 AT +25°C
VIN
LX
VOUT
FIGURE 13. POWER-DOWN GLITCH FOR UNIT LOT-3-1 AT +25°C AFTER BIASED IRRADIATION TO 100krad(Si) AND 50-300rad(Si)/S
Submit Document Feedback
14
TB504.0
April 21, 2016
Technical Brief 504
VIN
VOUT
LX
FIGURE 14. DC BEHAVIOR OF UNIT LOT-3-1 AT +25°C
Submit Document Feedback
15
TB504.0
April 21, 2016
Technical Brief 504
Discussion of Bench Testing Results
Testing began with all 40 units tested at +25°C for power-up,
power-down, and DC anomalous VOUT. Then four units were
selected for testing at temperature (+85°C and +125°C), based
on simulation results and bench testing indicating the worst case
condition to be high temperature. Finally six units were selected
for biased irradiation and these parts were again tested at
+25°C. The tabular results of all this testing is presented in
Table 3.
TABLE 3. RESULTS OF BENCH TESTING UNITS FOR ANOMALOUS VOUT RESPONSES FOR VIN RISING, FALLING AND DC OPERATION.
LOT
SN
TEMP
(°C)
krad(Si)
RISING
(mV)
FALLING
(mV)
DC
(mV)
LOT-1
2621
+25
0
109
192
683
LOT-1
2625
+25
0
25
70
289
LOT-1
2626
+25
0
134
92
218
LOT-1
2634
+25
0
147
219
814
LOT-1
2660
+25
0
109
122
212
LOT-1
2661
+25
0
102
109
166
LOT-1
2662
+25
0
25
154
492
LOT-1
2664
+25
0
128
141
134
LOT-1
2665
+25
0
122
116
406
LOT-1
2666
+25
0
113
192
801
LOT-1
2667
+25
0
70
128
387
LOT-1
2668
+25
0
78
147
567
LOT-1
2669
+25
0
89
179
498
LOT-1
2670
+25
0
83
76
317
LOT-1
2684
+25
0
70
467
595
LOT-1
2684
+85
0
184
261
907
LOT-1
2684
+125
0
184
286
920
LOT-1
2688
+25
0
116
206
620
LOT-1
2691
+25
0
154
160
548
LOT-2
2859
+25
0
70
89
418
LOT-2
2860
+25
0
116
179
580
LOT-2
2862
+25
0
63
LOT-2
2864
+25
0
166
141
762
LOT-2
2865
+25
0
141
173
729
LOT-2
2866
+25
0
106
166
498
LOT-2
2868
+25
0
141
193
814
LOT-2
2874
+25
0
128
173
801
LOT-3
1
+25
0
296
297
905
LOT-3
1
+25
100
627
448
LOT-3
2
+25
0
219
222
867
LOT-3
3
+25
0
212
265
867
LOT-3
3
+85
0
280
344
952
LOT-3
3
+125
0
280
389
1016
LOT-3
4
+25
0
212
232
873
LOT-3
4
+25
100
425
387
Submit Document Feedback
16
454
TB504.0
April 21, 2016
Technical Brief 504
TABLE 3. RESULTS OF BENCH TESTING UNITS FOR ANOMALOUS VOUT RESPONSES FOR VIN RISING, FALLING AND DC OPERATION. (Continued)
LOT
SN
TEMP
(°C)
krad(Si)
RISING
(mV)
FALLING
(mV)
DC
(mV)
LOT-3
5
+25
0
199
263
880
LOT-4
0
+25
0
219
303
867
LOT-4
0
+25
100
406
393
LOT-4
1
+25
0
193
283
847
LOT-4
2
+25
0
238
296
873
LOT-4
2
+85
0
306
395
965
LOT-4
2
+125
0
325
408
978
LOT-4
7
+25
0
231
237
873
LOT-4
7
+25
100
436
399
LOT-4
8
+25
0
219
375
867
LOT-5
5
+25
0
63
76
115
LOT-5
6
+25
0
26
86
179
LOT-5
7
+25
0
134
224
542
LOT-5
7
+85
0
235
325
920
LOT-5
7
+125
0
242
363
971
LOT-5
8
+25
0
128
147
215
LOT-5
8
+25
100
296
399
LOT-5
9
+25
0
96
237
LOT-5
9
+25
100
406
356
606
The power-up glitch results at +25°C are graphically presented in
Figure 15 on page 18. The extreme point correlates to unit LOT-31 and is represented in Figure 10 on page 13.
The power-down glitches at +25°C are graphically represented in
Figure 16 on page 18. The extreme value of 467mV corresponds
to LOT-1-2684 and is represented in Figure 12 on page 14. This
case is an outlier in its form and magnitude. All other parts
exhibited a discharge to zero as is the case in Figure 13 on
page 14.
Submit Document Feedback
17
TB504.0
April 21, 2016
Technical Brief 504
Power-Up Glitch at +25°C
350
300
296
250
mV
200
150
100
50
0
1
2
LOT-1
3
LOT-2
LOT-3
4
LOT-4
5
LOT-5
FIGURE 15. POWER-UP GLITCH MAGNITUDES AT +25°C PLOTTED BY PRODUCT LOT GROUPINGS
Power-Down Glitch at +25°C
500
467
450
400
350
mV
300
250
200
150
100
50
0
1
2
LOT-1
3
LOT-2
LOT-3
4
LOT-4
5
LOT-5
FIGURE 16. POWER-DOWN GLITCH MAGNITUDES AT +25°C PLOTTED BY PRODUCT LOT GROUPINGS
Submit Document Feedback
18
TB504.0
April 21, 2016
Technical Brief 504
Anomalous DC Level at +25°C
1000
905
900
800
700
mV
600
500
400
300
200
100
0
1
2
LOT-1
3
LOT-2
LOT-3
4
LOT-4
5
LOT-5
FIGURE 17. ANOMALOUS DC VOUT MAGNITUDES AT +25°C PLOTTED BY PRODUCT LOT GROUPINGS
The parts were also operated with VIN being a DC level and
adjusted to give the maximum VOUT output. The results are
graphically represented in Figure 17. All parts tested exhibited
output voltages less than the set-point at 1.2V.
Four units were selected to test at elevated temperature. As
represented in Figure 18 on page 20 all four units tended toward
larger power-up glitches as temperature increased. The
maximum delta from +25°C was only 114mV at +125°C and
the resulting maximum glitch at +125°C was only 325mV. The
power-down glitch magnitudes are shown in Figure 19 on
page 20. Unit LOT-1-2684 showed more typical behavior at the
elevated temperatures than it did at +25°C. The +125°C
behavior is depicted in Figure 20 on page 21. This behavior lacks
the abrupt rise in VOUT seen in Figure 12 on page 14 and is
responsible for the reduced glitch magnitude.
Another six units were selected for post radiation testing. The
units were irradiated in the standard biased configuration at
50-300rad(Si)/s to a dose of 100krad(Si). Then, the parts were
again tested for glitches at +25°C. Figure 21 on page 21 shows
the pre- and post-irradiation power-up glitch magnitudes
measured at +25°C. The irradiation led to larger glitch
magnitudes with the largest one being LOT-3-1 as already shown
in Figure 11 on page 13. The power-down glitch behavior over
radiation is shown in Figure 22 on page 22. Again the extreme
case is that of LOT-3-1 and has already been shown in Figure 11
on page 13.
Nothing in all the testing done implies that the power-up or
power-down behavior of the part will result in the VOUT exceeding
the set point (1.2V in the bench cases here). This is consistent
with the simulation results.
Submit Document Feedback
19
TB504.0
April 21, 2016
Technical Brief 504
POWER-UP GLITCH WITH TEMPERATURE
350
300
250
mV
200
150
100
50
LOT-5-7
LOT-1-2684
LOT-3-3
LOT-4-2
0
0
20
40
60
80
100
120
140
AMBIENT TEMPERATURE (°C)
FIGURE 18. POWER-UP GLITCH MAGNITUDES AT TEMPERATURES +25°C, +85°C, AND +125°C FOR FOUR SAMPLED UNITS
POWER-DOWN GLITCH WITH TEMPERATURE
500
450
400
350
mV
300
250
200
150
100
50
LOT-5-7
LOT-1-2684
LOT-3-3
LOT-4-2
0
0
20
40
60
80
100
120
140
AMBIENT TEMPERATURE (°C)
FIGURE 19. POWER-DOWN GLITCH MAGNITUDES AT TEMPERATURES +25°C, +85°C, AND +125°C FOR FOUR SAMPLED UNITS
Submit Document Feedback
20
TB504.0
April 21, 2016
Technical Brief 504
VIN
LX
VOUT
FIGURE 20. LOT-1-2684 POWER-DOWN GLITCH AT +125°C
POWER-UP GLITCH CHANGE WITH 100krad(Si)
700
600
500
mV
400
300
200
100
LOT-5-8
LOT-5-9
LOT-3-1
LOT-3-4
LOT-4-0
LOT-4-7
0
0
100
TID (krad(Si))
FIGURE 21. PRE- AND POST-RADIATION (100krad(Si)) +25°C POWER-UP GLITCH MAGNITUDES
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is
cautioned to verify that the document is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com
Submit Document Feedback
21
TB504.0
April 21, 2016
Technical Brief 504
POWER-DOWN GLITCH CHANGE WITH 100krad(Si)
500
450
400
350
mV
300
250
200
150
100
50
LOT-5-8
LOT-5-9
LOT-3-1
LOT-3-4
LOT-4-0
LOT-4-7
0
0
100
TID (krad(Si))
FIGURE 22. PRE- AND POST-RADIATION (100krad(Si)) +25°C POWER-DOWN GLITCH MAGNITUDES
ISL70001SEH, ISL70001SRH
Implemented as Clock Slave or
Externally Clocked Device
The ISL70001SEH, ISL70001SRH, when set as a master, the
control signal path that controls output activity is such that LX
activity starts at ~1.5V prior to it being inhibited by a fuse read at
~1.7V. This design weakness was corrected on the ISL70001A
and all subsequent ISL7000x devices.
In the ISL70001SEH, ISL70001SRH when in slave mode, the
control signal path from the SYNC input to the output and LX
activity is inhibited until the PORSEL selected UVLO threshold is
satisfied. This is a different signal path than exists when the
ISL70001SEH, ISL70001SRH is in master mode.
Figure 23 illustrates the expected behavior when a master and a
SYNC clocked slave or externally clocked slave device is powered
up slowly. The clocked slave device has its PORSEL = high and
the master PORSEL = low. The slow rising PVIN (BLUE) results in
the master LX activity (GREEN)) accompanied by SYNC (RED)
activity, however, no slave LX (YELLOW) activity until the clocked
slave UVLO is satisfied.
Summary
The conditions where ISL70001SEH, ISL70001SRH do not
exhibit LX activity below UVLO.
There are several ways to avoid the possibility of ISL70001SEH,
ISL70001SRH LX pin pulsing. Any 1 of these 3 conditions will
inhibit the LX pin pulsing below UVLO.
1. External Clock
a. If the M/S pin is tied low and an external clock is applied
to SYNC, the LX pulsing will not occur until UVLO is
satisfied.
PVIN
2. Enable
SLAVE LX
a. If the EN pin is held at <0.5 V until VIN > 1.6V, the LX pin
pulsing will not occur.
b. Using a suitable external resistor divider between VIN
and EN will prevent LX pin pulsing.
MASTER LX
3. PVIN Ramp
SYNC
a. A 10V/ms minimum PVIN ramp will prevent the LX pin
pulsing.
FIGURE 23. SLOW PVIN RISE, RESULTING IN EARLY MASTER LX AND
SYNC ACTIVITY WITH NO CLOCKED SLAVE LX ACTIVITY
Submit Document Feedback
22
TB504.0
April 21, 2016