ISL54207 IGNS EW DES N R O F NDED EMENT COMME REPL AC D E NO T RE D N ter at E OMM Sheet port Cen /tsc December 5, 2006 p u S l NO REC Data a m nic tersil.co our Tech contact ERSIL or www.in T 1-888-IN Low Voltage, Dual SPDT, USB/CVBS/ Audio Switches, with Negative Signal Capability FN6403.0 Features • High Speed (480Mbps) Signaling Capability per USB 2.0 • Low Distortion Negative Signal Capability The Intersil ISL54207 dual SPDT (Single Pole/Double Throw) switches combine low distortion audio/video and accurate USB 2.0 high speed (480Mbps) data signal switching in the same low voltage device. When operated with a 2.7V to 3.6V single supply, these analog switches allow audio/video signal swings below-ground, allowing the use of a common USB and audio/video connector in digital cameras, camcorders and other portable battery powered Personal Media Player devices. • Detection of VBUS Voltage on USB Cable • Control Pin to Open all Switches and Enter Low Power State • Low Distortion Mono Audio Signal - THD+N at 20mW into 32Load . . . . . . . . . . . . . <0.1% • Low Distortion Color Video Signal - Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . 0.28% - Differential Phase. . . . . . . . . . . . . . . . . . . . . . . .0.04deg The ISL54207 incorporates circuitry for detection of the USB VBUS voltage, which is used to switch between the audio/video and USB signal sources in the portable device. The part has a control pin to open all the switches and put the part in a low power down state. • Cross-talk (4MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . -78dB • Single Supply Operation (VDD) . . . . . . . . . . . . 2.7V to 3.6V • -3dB Bandwidth USB Switch . . . . . . . . . . . . . . . . . 630MHz • Available in TQFN and TDFN Packages The ISL54207 is available in a small 10 Ld 2.1mm x 1.6mm ultra-thin TQFN package and a 10Ld 3mm x 3mm TDFN package. It operates over a temperature range of -40 to +85°C. • Pb-Free Plus Anneal Available (RoHS Compliant) • Compliant with USB 2.0 Short Circuit Requirements Without Additional External Components Related Literature Applications • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” • Digital Camera and Camcorders • Video MP3 and other Personal Media Players • Application Note AN557 “Recommended Test Procedures for Analog Switches” • Cellular/Mobile Phones • PDA’s • Audio/Video/USB Switching Application Block Diagram VDD VBUS CONTROLLER ISL54207 CTRL USB and AUDIO/VIDEO JACK LOGIC CIRCUITRY 22k 4M 4M NO1 COM1 NO2 50k COM2 50k D- USB HIGH-SPEED D+ TRANSCEIVER NC1 NTSC OR PAL NC2 VIDEO AUDIO GND 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54207 Pinouts (Note 1) ISL54207 (10 LD TDFN) TOP VIEW CTRL ISL54207 (10 LD TQFN) TOP VIEW 10 9 NO1 8 NO2 3 7 NC1 4 6 NC2 VDD 1 VBUS 2 COM 1 COM 2 VDD 1 VBUS 2 4M LOGIC CONTROL 4M 4M 10 CTRL 9 NO1 LOGIC CONTROL COM 1 3 8 NO2 COM 2 4 7 NC1 GND 5 6 NC2 50k 50k 50k 50k GND 5 4M NOTE: 1. ISL54207 Switches shown for VBUS = Logic “0” and CTRL = Logic “1”. Truth Table Pin Descriptions ISL54207 ISL54207 VBUS CTRL NC1, NC2 NO1, NO2 PIN NO. NAME 0 0 OFF OFF 1 VDD 0 1 ON OFF 2 VBUS Digital Control Input 1 X OFF ON 3 COM1 Voice/Video and USB Common Pin 4 COM2 Voice/Video and USB Common Pin 5 GND Ground Connection 6 NC2 Audio or Video Input 7 NC1 Audio or Video Input 8 NO2 USB Differential Input 9 NO1 USB Differential Input 10 CTRL Digital Control Input (Audio Enable) CTRL: Logic “0” when 0.5V, Logic “1” when 1.4V VBUS: Logic “0” when VDD + 0.2V or Floating, Logic “1” when VDD + 0.8V FUNCTION Power Supply Ordering Information PART NUMBER (Note) PART MARKING TEMP. RANGE (°C) PACKAGE (Pb-Free) PKG. DWG. # ISL54207IRUZ-T FP -40 to +85 10 Ld 2.1 x 1.6mm TQFN Tape and Reel L10.2.1x1.6A ISL54207IRZ-T 207Z -40 to +85 10 Ld 3mm x 3mm TDFN Tape and Reel L10.3x3A ISL54207IRZ 207Z -40 to +85 10 Ld 3mm x 3mm TDFN L10.3x3A NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate or NiPdAu termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN6403.0 December 5, 2006 ISL54207 Absolute Maximum Ratings Thermal Information VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6.0V Input Voltages NCx, NOx(Note 2) . . . . . . . . . . . . . . . . . . . - 2V to ((VDD) + 0.3V) VBUS (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2V to 5.5V CTRL (Note 2) . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((VDD) + 0.3V) Output Voltages COMx (Note 2) . . . . . . . . . . . . . . . . . . . . . . -2V to ((VDD) + 0.3V) Continuous Current (NCx, COMx) . . . . . . . . . . . . . . . . . . . ±150mA Peak Current (NCx, COMx) (Pulsed 1ms, 10% Duty Cycle, Max). . . . . . . . . . . . . . . . ±300mA Continuous Current (NOx) . . . . . . . . . . . . . . . . . . . . . . . . . . ±40mA Peak Current (NOx) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA ESD Rating: HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >7kV MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >450V CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >2kV Thermal Resistance (Typical, Note 3) JA (°C/W) 10 Ld TQFN Package . . . . . . . . . . . . . . . . . . . . . . . 10 Ld 3x3 TDFN Package. . . . . . . . . . . . . . . . . . . . . 130 110 Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C Maximum Storage Temperature Range. . . . . . . . . . . . -65°C to +150°C Operating Conditions Temperature Range ISL54207IRUZ and ISL54207IRZ. . . . . . . . . . . . . . . -40°C to +85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. Signals on NOx, NCx, COMx, CTRL, VBUS exceeding VDD or GND by specified amount are clamped. Limit current to maximum current ratings. 3. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V, VCTRLH = 1.4V, VCTRLL = 0.5V, (Notes 4, 6), unless otherwise specified. PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS ANALOG SWITCH CHARACTERISTICS Audio/Video Switches (NC1, NC2) Analog Signal Range, VANALOG VDD = 3.0V, VBUS = float, CTRL = 1.4V Full -1.5 - 1.5 V ON Resistance, rON VDD = 3.0V, VBUS = float, CTRL = 1.4V, ICOMx = 100mA, VNCx = -0.85V to 0.85V, (See Figure 3) 25 - 2.65 4 Full - - 5.5 25 - 0.02 0.13 Full - - 0.16 25 - 0.03 0.05 Full - - 0.07 VDD = 3.6V, VBUS = float, CTRL = 1.4V, VCOM- or VCOM+ = -0.85V, 0.85V, VNCx = -0.85V, 0.85V, VNOx = floating, Measure current through the discharge pull-down resistor and calculate resistance value. 25 - 50 - k Analog Signal Range, VANALOG VDD = 3.0V, VBUS = 5.0V, CTRL = 0V or 3V Full 0 - VDD V ON Resistance, rON VDD = 3.6V, VBUS = 4.4V, CTRL = 0V or 3.6V, ICOMx = 40mA, VNOx = 0V to 400mV (See Figure 4) 25 - 4.6 5 Full - - 6.5 25 - 0.06 0.5 Full - - 0.55 25 - 0.4 0.6 Full - - 1.0 rON Matching Between Channels, rON VDD = 3.0V, VBUS = float, CTRL = 1.4V, ICOMx = 100mA, VNCx = Voltage at max rON over signal range of -0.85V to 0.85V, (Note 8) rON Flatness, rFLAT(ON) VDD = 3.0V, VBUS = float, CTRL = 1.4V, ICOMx = 100mA, VNCx = -0.85V to 0.85V, (Note 7) Discharge Pull-Down Resistance, RNC1, RNC2 USB Switches (NO1, NO2) rON Matching Between Channels, RON VDD = 3.6V, VBUS = 4.4V, CTRL = 0V or 3.6V, ICOMx = 40mA, VNOx = Voltage at max rON, (Note 8) rON Flatness, rFLAT(ON) VDD = 3.6V, VBUS = 4.4V, CTRL = 0V or 3.6V, ICOMx = 40mA, VNOx = 0V to 400mV, (Note 7) 3 FN6403.0 December 5, 2006 ISL54207 Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V, VCTRLH = 1.4V, VCTRLL = 0.5V, (Notes 4, 6), unless otherwise specified. (Continued) PARAMETER TEST CONDITIONS OFF Leakage Current, ID+(OFF) or ID-(OFF) VDD = 3.6V, VBUS = 0V, CTRL = 3.6V, VCOMx = 0.5V, 0V, VNOx = 0V, 0.5V, VNCx = float ON Leakage Current, IDx VDD = 3.3V, VBUS = 5.25V, CTRL = 0V or 3.6V, VNOx = 2.0V, VCOMx, VNCx = float TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS 25 -10 - 10 nA Full -70 - 70 nA 25 -10 2 10 nA Full -75 - 75 nA DYNAMIC CHARACTERISTICS Turn-ON Time, tON VDD = 2.7V, RL = 50, CL = 10pF, (See Figure 1) 25 - 67 - ns Turn-OFF Time, tOFF VDD = 2.7V, RL = 50, CL = 10pF, (See Figure 1) 25 - 48 - ns Break-Before-Make Time Delay, tD VDD = 2.7V, RL = 50, CL = 10pF, (See Figure 2) 25 - 18 - ns Skew, tSKEW VDD = 3.0V, VBUS = 5.0V, CTRL = 0V or 3V, RL = 45, CL = 10pF,tR = tF = 720ps at 480Mbps, (Duty Cycle = 50%) (See Figure 7) 25 - 50 - ps Total Jitter, tJ VDD = 3.0V, VBUS = 5.0V, CTRL = 0V or 3V, RL = 45, CL = 10pF,tR = tF = 750ps at 480Mbps 25 - 210 - ps Propagation Delay, tPD VDD = 3.0V, VBUS = 5.0V, CTRL = 0V or 3V, RL = 45, CL = 10pF,See Figure 7) 25 - 250 - ps Crosstalk (Channel-to-Channel), NC2 to COM1, NC1 to COM2 VDD = 3.0V, VBUS = float, CTRL = 3.0V, RL = 75, f = 4MHz, VNCx = 300mVP-P , (See Figure 6) 25 - -78 - dB Differential Gain VIN = 300mVP-P, VOFFSET = 0V to 0.7V, f = 3.58MHz, RL = 75 25 - 0.28 - % Differential Phase VIN = 300mVp-p, VOFFSET = 0V to 0.7V, f = 3.58MHz, RL = 75 25 - 0.04 - ° Total Harmonic Distortion f = 20Hz to 20kHz, VDD = 3.0V, VBUS = float, CTRL = 3.0V, VNCx = 0.707VRMS (2VP-P), RL = 32 25 - 0.06 - % NCx (Audio/Video) Switch -3dB Bandwidth Signal = 8dBm, RL = 75,CL = 5pF 25 - 338 - MHz NOx (USB) Switch -3dB Bandwidth Signal = 0dBm, 0.2VDC offset, RL = 50,CL = 5pF 25 - 630 - MHz NOx OFF Capacitance, CNOx(OFF) f = 1MHz, VDD = 3.0V, VBUS = float, CTRL = 3.0V, VD- or VD+ = VCOMx = 0V, (See Figure 5) 25 - 6 - pF NCx OFF Capacitance, CNCx(OFF) f = 1MHz, VDD = 3.0V, VBUS = 5.0V, CTRL = 0V or 3V, VL or VR = VCOMx = 0V, (See Figure 5) 25 - 9 - pF COMx ON Capacitance, CCOMx(ON) f = 1MHz, VDD = 3.0V, VBUS = 5.0V, CTRL = 0V or 3V, VD- or VD+ = VCOMx = 0V, (See Figure 5) 25 - 10 - pF Full 2.7 3.6 V 25 - 6 8 A Full - - 10 A 25 - 1 7 nA Full - - 140 nA POWER SUPPLY CHARACTERISTICS Power Supply Range, VDD Positive Supply Current, IDD VDD = 3.6V, VBUS = float or 5.25V, CTRL = 1.4V Positive Supply Current, IDD (Low Power State) VDD = 3.6V, VBUS = 0V or float, CTRL = 0V or float DIGITAL INPUT CHARACTERISTICS VBUS Voltage Low, VBUSL VDD = 2.7V to 3.6V Full - - VDD + 0.2 V VBUS Voltage High, VBUSH VDD = 2.7V to 3.6V Full VDD + 0.8 - - V CTRL Voltage Low, VCTRLL VDD = 2.7V to 3.6V Full - - 0.5 V 4 FN6403.0 December 5, 2006 ISL54207 Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V, VCTRLH = 1.4V, VCTRLL = 0.5V, (Notes 4, 6), unless otherwise specified. (Continued) PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 5) MIN TYP (NOTE 5) MAX UNITS CTRL Voltage High, VCTRLH VDD = 2.7V to 3.6V Full 1.4 - - V Input Current, IBUSL, ICTRLL VDD = 3.6V, VBUS = 0V or float, CTRL = 0V or float Full -50 20 50 nA Input Current, IBUSH VDD = 3.6V, VBUS = 5.25V, CTRL = 0V or float Full -2 1.1 2 A Input Current, ICTRLH VDD = 3.6V, VBUS = 0V or float, CTRL = 3.6V Full -2 1.1 -2 A VBUS Pull-Down Resistor, RVBUS VDD = 3.6V, VBUS = 5.25V, CTRL = 0V or float Full - 4 - M CTRL Pull-Down Resistor, RCTRL VDD = 3.6V, VBUS = 0V or float, CTRL = 3.6V Full - 4 - M NOTES: 4. VLOGIC = Input voltage to perform proper function. 5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation. 7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range. 8. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON value, between NC1 and NC2 or between NO1 and NO2. Test Circuits and Waveforms VBUSH LOGIC INPUT VBUSL 50% VINPUT tOFF SWITCH INPUT VINPUT SWITCH INPUT C CTRL VOUT NO or NC COMx VBUS VOUT 90% SWITCH 0V OUTPUT VDD tr < 20ns tf < 20ns 90% VBUS GND RL 50 CL 10pF tON Logic input waveform is inverted for switches that have the opposite logic sense. Repeat test for all switches. CL includes fixture and stray capacitance. RL --------------------------V OUT = V (INPUT) R + r L ON FIGURE 1A. MEASUREMENT POINTS FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES 5 FN6403.0 December 5, 2006 ISL54207 Test Circuits and Waveforms (Continued) VDD C CTRL NOx VINPUT VBUSH LOGIC INPUT VOUT COMx NCx GND VBUS VOUT CL 10pF RL 50 VBUS VBUSL 90% SWITCH OUTPUT 0V tD Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 2B. TEST CIRCUIT FIGURE 2A. MEASUREMENT POINTS FIGURE 2. BREAK-BEFORE-MAKE TIME VDD VDD C rON = V1/100mA C rON = V1/40mA CTRL CTRL NCx NOx VNOx VNCx VBUS V1 100mA OV or Float 40mA COMx GND Repeat test for all switches. VBUS V1 4.4V to 5.25V COMx GND Repeat test for all switches. FIGURE 3. AUDIO rON TEST CIRCUIT 6 FIGURE 4. USB rON TEST CIRCUIT FN6403.0 December 5, 2006 ISL54207 Test Circuits and Waveforms (Continued) VDD VDD C C CTRL CTRL SIGNAL GENERATOR NCx or NOx NCx VBUS IMPEDANCE ANALYZER VBUS 0V or Float VBUSL or VBUSH COMx GND 75 COMx R or L COMx ANALYZER N.C. GND RL Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches Repeat test for all switches. FIGURE 5. CAPACITANCE TEST CIRCUIT FIGURE 6. AUDIO CROSSTALK TEST CIRCUIT VDD C tri CTRL 90% DIN+ 10% 50% VBUSH tskew_i DIN- 90% VBUS 15.8 DIN+ 50% COM1 143 10% DIN- tfi tro 15.8 OUT+ NO1 CL COM2 OUT- NO2 CL 143 45 45 90% OUT+ OUT- 10% 50% GND tskew_o 50% 90% 10% tf0 |tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals. |tfo - tfi| Delay Due to Switch for Falling Input and Falling Output Signals. |tskew_0| Change in Skew through the Switch for Output Signals. |tskew_i| Change in Skew through the Switch for Input Signals. FIGURE 7A. MEASUREMENT POINTS FIGURE 7B. TEST CIRCUIT FIGURE 7. SKEW TEST 7 FN6403.0 December 5, 2006 ISL54207 Application Block Diagram VDD USB AND AUDIO/VIDEO JACK mCONTROLLER ISL54207 VBUS CTRL LOGIC CIRCUITRY 22k 4M 4M NO1 COM1 NO2 50k COM2 50k D- USB HIGH-SPEED D+ TRANSCEIVER NC1 NTSC or PAL NC2 VIDEO AUDIO GND Detailed Description NC1 and NC2 Audio/Video Switches The ISL54207 device is a dual single pole/double throw (SPDT) analog switch device that operates from a single DC power supply in the range of 2.7V to 3.6V. It was designed to function as a dual 2 to 1 multiplexer to select between USB differential data signals and mono audio/composite video baseband signals (CVBS). It comes in tiny TQFN and TDFN packages for use in cameras, camcorders, video MP3 players, PDAs, cell phones, and other personal media players. The two NC (normally closed) audio/video switches (NC1, NC2) are 3 switches that can pass signals that swing below ground by as much as 1.5V. They were designed to pass ground reference audio signals and DC restored composite base-band signals (CVBS), including negative synchronizing pulse with minimal insertion loss and very low distortion and degradation. The part consists of two 3 audio/video switches and two 5 USB switches. The audio/video switches can accept signals that swing below ground. They were designed to pass ground reference audio or dc restored with synch composite video signals with minimal distortion. The USB switches were designed to pass high-speed USB differential data signals with minimal edge and phase distortion. The ISL54207 was specifically designed for digital cameras, camcorders, MP3 players, cell phones and other personal media player applications that need to combine the audio/video jacks and the USB data connector into a single shared connector, thereby saving space and component cost. A typical application block diagram of this functionality is shown above. The ISL54207 incorporates circuitry for the detection of the USB VBUS voltage, which is used to switch between the audio/video drivers and USB transceiver of the media player. The ISL54207 contains a logic control pin (CTRL) that when driven Low while VBUS is Low, opens all switches and puts the part into a low power state, drawing typically 1nA of IDD current. The -3dB bandwidth into 75 is 338MHz (Figure 17). Crosstalk between NC1 and NC2 @ 4MHz is -78dB (Figure 16), which allows composite video to be routed through one switch and mono-audio through the other switch with little interference. The recommended maximum signal range is from -1.5V to 1.5V. You can apply positive signals greater than 1.5V but the rON resistance of the switch increases rapidly above 1.5V. The signal should not be allowed to exceed the VDD rail or swing more negative than -1.5V. Over a signal range of ±1V (0.707Vrms) with VDD > 2.7V, these switches have an extremely low rON resistance variation. They can pass a ground referenced audio signal with very low distortion (<0.06% THD+N) when delivering 15.6mW into a 32headphone speaker load. See Figures 10, 11, 12, and 13 THD+N performance curves. Figure 8 and 9 shows the vector scope plots of a standard NTSC color bar signal at both the input (Figure 8) and output (Figure 9) of the ISL54207. The plots show that except for a little attenuation due to switch rON and test fixture cabling, there is virtually no degradation of the video waveform through the switch. A detailed description of the two types of switches is provided in the following sections. The USB transmission and audio/video playback are intended to be mutually exclusive operations. 8 FN6403.0 December 5, 2006 ISL54207 NO1 and NO2 USB Switches The two NO (normally open) USB switches (NO1, NO2) are 5 bidirectional switches that are designed to pass high-speed USB differential signals in the range of ±0V to 400mV. The switches have low capacitance and high bandwidth to pass USB high-speed signals (480Mbps) with minimum edge and phase distortion to meet USB 2.0 signal quality specifications. See Figure 14 for High-speed Eye Pattern taken with switch in the signal path. The maximum signal range for the USB switches is from -1.5V to VDD. The signal voltage at NO1 and NO2 should not be allowed to exceed the VDD voltage rail or go below ground by more than -1.5V. The NO switches are active (turned ON) whenever the VBUS voltage is to VDD + 0.8V. VBUS is internally pulled low, so when VBUS is floating, the USB switches are OFF. FIGURE 8. VECTOR-SCOPE PLOT BEFORE SWITCH Note: Whenever the NO switches are ON, the audio and video drivers need to be at AC or DC ground or floating to keep from interfering with the data transmission. ISL54207 Operation The discussion that follows will discuss using the ISL54207 in the typical application shown in the block diagram on page 8. LOGIC CONTROL The state of the ISL54207 device is determined by the voltage at the VBUS pin (pin 2) and the CTRL pin (pin 10). Refer to truth-table on page 2 of the data sheet. The VBUS pin and CTRL pin are internally pulled low through 4Mresistors to ground and can be left floating. The CTRL control pin is only active when VBUS is logic “0”. Logic control voltage levels: FIGURE 9. VECTOR-SCOPE PLOT AFTER SWITCH Figure 18 shows the differential gain (DG) and differential phase (DP) plots at the output of the switch using an actual NTSC composite video signal and a VM700A Video Measurement Test Set. DG = 0.28% and DP = 0.04°. These NC switches are uni-directional switches. The audio/video sources should be connected at the NC side of the switch (pins 7 and 8) and the speaker load and video receiver should be connected at the COM side of the switch (pins 3 and 4). The NC switches are active (turned ON) whenever the VBUS voltage is to VDD + 0.2V or floating and the CTRL voltage to 1.4V. Note: Whenever the NC switches are ON the USB transceivers need to be in the high impedance state or static high or low state. 9 VBUS = Logic “0” (Low) when VBUS VDD + 0.2V or Floating. VBUS = Logic “1” (High) when VBUS VDD + 0.8V CTRL = Logic “0” (Low) when 0.5V or floating. CTRL = Logic “1” (High) when 1.4V Audio/Video Mode If the VBUS pin = Logic “0” and CTRL pin = Logic “1,” the part will be in the Audio/Video mode. In Audio/Video mode the NC1 and NC2 3 audio/video switches are ON and the NO1 and NO2 5 USB switches are OFF (high impedance). In a typical application, VDD will be in the range of 2.7V to 3.6V and will be connected to the battery or LDO of the media player. When a audio/video jack is plugged into the common connector, nothing gets connected at the VBUS pin (it is floating) and as long as the CTRL = Logic “1,” the ISL54207 part remains in the audio/video mode and the media player audio and video drivers can drive the speaker and video display. FN6403.0 December 5, 2006 ISL54207 USB Mode If the VBUS pin = Logic “1” and CTRL pin = Logic “0” or Logic “1,” the part will go into USB mode. In USB mode, the NO1 and NO2 5 switches are ON and the NC1 and NC2 3 audio switches are OFF (high impedance). When a USB cable from a computer or USB hub is connected at the common connector, the voltage at the VBUS pin will be driven to be in the range of 4.4V to 5.25V. The ISL54207 part will go into the USB mode. In USB mode, the computer or USB hub transceiver and the media player USB transceiver are connected and digital data will be able to be transmitted back and forth. When the USB cable is disconnected, the ISL54207 automatically turns the NO1 and NO2 switches OFF. Low Power Mode If the VBUS pin = Logic “0” and CTRL pin = Logic “0,” the part will be in the Low Power mode. In the Low Power mode, the NCx switches and the NOx switches are OFF (high impedance). In this state, the device draws typically 1nA of current. EXTERNAL VBUS SERIES RESISTOR The ISL54207 contains a clamp circuit between VBUS and VDD. Whenever the VBUS voltage is greater than the VDD voltage by more than 2.55V, current will flow through this clamp circuitry into the VDD power supply bus. circuit is not active and no current will flow through the clamp into the VDD supply. In a USB application, the situation can exist where the VBUS voltage from the computer could be applied at the VBUS pin before the VDD voltage is up to its normal operating voltage range and current will flow through the clamp into the VDD power supply bus. This current could be quite high when VDD is OFF or at 0V and could potentially damage other components connected in the circuit. In the application circuit, a 22k resistor has been put in series with the VBUS pin to limit the current to a safe level during this situation. It is recommended that a current limiting resistor in the range of 10k to 50k be connected in series with the VBUS pin. It will have minimal impact on the logic level at the VBUS pin during normal USB operation and protect the circuit during the time VBUS is present before VDD is up to its normal operating voltage. Note: No external resistor is required in applications where VBUS will not exceed VDD by more than 2.55V. POWER The power supply connected at VDD (pin 1) provides power to the ISL54207 part. Its voltage should be kept in the range of 2.7V to 3.6V when used in a USB/Audio/Video application to ensure you get proper switching when the VBUS voltage is at its lower limit of 4.4V. During normal USB operation, VDD is in the range of 2.7V to 3.6V and VBUS is in the range of 4.4V to 5.25V. The clamp Typical Performance Curves TA = +25°C, Unless Otherwise Specified 0.11 0.4 0.1 3VP-P 0.3 0.09 VDD = 2.6V 0.08 THD+N (%) THD+N (%) RLOAD = 32 VDD = 3V RLOAD = 32 VLOAD = 0.707VRMS 0.07 VDD = 2.7V 0.06 VDD = 3V 0.05 VDD = 3.6V 0.2 2.5VP-P 0.1 2VP-P 1VP-P 0 0.04 20 200 2k FREQUENCY (Hz) 20k FIGURE 10. THD+N vs SUPPLY VOLTAGE vs FREQUENCY 10 20 200 2k FREQUENCY (Hz) 20k FIGURE 11. THD+N vs SIGNAL LEVELS vs FREQUENCY FN6403.0 December 5, 2006 ISL54207 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) 0.5 0.5 RLOAD = 32 FREQ = 1kHz VDD = 3V 0.4 0.3 THD+N (%) THD+N (%) 0.4 RLOAD = 32 FREQ = 1kHz VDD = 3V 0.2 0.3 0.2 0.1 0.1 0 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0 OUTPUT VOLTAGE (VP-P) 10 20 30 40 50 OUTPUT POWER (mW) FIGURE 13. THD+N vs OUTPUT POWER VOLTAGE (835mV/DIV) FIGURE 12. THD+N vs OUTPUT VOLTAGE TIME (10ns/DIV) FIGURE 14. EYE PATTERN: 480Mbps WITH NOx SWITCHES IN THE SIGNAL PATH 11 FN6403.0 December 5, 2006 ISL54207 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) 1 0 NOx SWITCH -10 -1 -20 -2 -30 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 0 -3 -4 -40 -50 -60 -70 -80 -90 RL = 50 VIN = 0.2VP-P to 2VP-P 1M 10M 100M FREQUENCY (Hz) 1G -110 0.001 0.01 0.1 1 3 6 10 FREQUENCY (MHz) 100 500 FIGURE 16. VIDEO TO AUDIO CROSSTALK GAIN (%) FIGURE 15. FREQUENCY RESPONSE 1 NCx SWITCHES 0 -1 -2 PHASE (DEG) NORMALIZED GAIN (dB) RL = 75 VIN = 0.2VP-P to 2VP-P -3 -4 RL = 75 VIN = 0.2VP-P to 2VP-P 1M 10M 100M FREQUENCY (Hz) FIGURE 17. FREQUENCY RESPONSE 1G FIGURE 18. DIFFERENTIAL PHASE AND DIFFERENTIAL GAIN Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND (TDFN Paddle Connection: Tie to GND or Float) TRANSISTOR COUNT: 98 PROCESS: Submicron CMOS 12 FN6403.0 December 5, 2006 ISL54207 Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN) D 6 INDEX AREA 2X A L10.2.1x1.6A B N 10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS E SYMBOL 0.10 C 1 2X 2 0.10 C TOP VIEW C A SEATING PLANE 1 MAX 0.55 - A1 - - 0.05 - 0.127 REF - b 0.15 0.20 0.25 5 D 2.05 2.10 2.15 - E 1.55 1.60 1.65 - A1 SIDE VIEW k 0.20 - - L 0.35 0.40 0.45 4xk 2 NX L N 0.50 BSC - NX b 2 Nd 4 3 Ne 1 3 0 - 12 NOTES: 5 BOTTOM VIEW CL NX (b) (A1) L 5 e SECTION "C-C" TERMINAL TIP C C 4 Rev. 3 6/06 0.10 M C A B 0.05 M C 3 (ND-1) X e - 10 e - N (DATUM B) N-1 NOTES 0.50 e (DATUM A) PIN #1 ID NOMINAL 0.45 A3 0.10 C 0.05 C MIN A FOR ODD TERMINAL/SIDE b 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on D and E side, respectively. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Maximum package warpage is 0.05mm. 8. Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. 2.50 1.75 0.05 MIN L 2.00 0.80 0.275 0.10 MIN DETAIL “A” PIN 1 ID 0.25 0.50 LAND PATTERN 10 13 FN6403.0 December 5, 2006 ISL54207 Thin Dual Flat No-Lead Plastic Package (TDFN) L10.3x3A 2X 0.10 C A A 10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE D MILLIMETERS 2X 0.10 C B E B // A C SEATING PLANE D2 (DATUM B) 6 INDEX AREA 0.10 C 0.08 C A3 SIDE VIEW 7 8 MAX NOTES A 0.70 0.75 0.80 - A1 - - 0.05 - 0.20 REF b 0.20 0.25 0.30 1 5, 8 D 2.95 3.0 3.05 - D2 2.25 2.30 2.35 7, 8 E 2.95 3.0 3.05 - E2 1.45 1.50 1.55 7, 8 e 0.50 BSC - k 0.25 - - - L 0.25 0.30 0.35 8 N 10 2 Nd 5 3 Rev. 3 3/06 NOTES: 2 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. NX k 3. Nd refers to the number of terminals on D. 4. All dimensions are in millimeters. Angles are in degrees. E2 E2/2 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX L N N-1 NX b e (Nd-1)Xe REF. BOTTOM VIEW 5 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 0.10 M C A B 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Compliant to JEDEC MO-229-WEED-3 except for D2 dimensions. CL NX (b) NOMINAL D2/2 (DATUM A) 8 MIN A3 6 INDEX AREA TOP VIEW SYMBOL (A1) L1 5 9 L e SECTION "C-C" C C TERMINAL TIP FOR ODD TERMINAL/SIDE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 FN6403.0 December 5, 2006