DATASHEET

ISL54210
Features
The Intersil ISL54210 dual SPDT (Single Pole/Double
Throw) switch combines low distortion audio and
accurate USB 2.0 high-speed data (480Mbps) signal
switching in the same low voltage device. When
operated with a 2.7V to 3.6V single supply, these analog
switches allow audio signal swings below-ground,
allowing the use of a common USB and audio
headphone connector in Personal Media Players and
other portable battery powered devices.
• High Speed (480Mbps) and Full Speed (12Mbps)
Signaling Capability per USB 2.0
The ISL54210 incorporates circuitry for the detection of
the USB VBUS voltage, which is used to switch between
the audio and USB signal sources.
• Detection of VBUS Voltage on USB Cable
• Low Distortion Negative Signal Capability
• Clickless/Popless Audio Switches
• Enable Pin to Open all Switches
• Low Distortion Headphone Audio Signals
- THD+N at 1mW into 32Ω Load. . . . . . . . . 0.014%
• Crosstalk (20Hz to 20kHz). . . . . . . . . . . . . -100dB
• Off-Isolation (20Hz to 100kHz) . . . . . . . . . . . 95dB
• Single Supply Operation (VDD) . . . . . . 2.7V to 3.6V
It has an enable pin (CTRL) to open all switches and
activate the audio click/pop (C/P) circuitry. The high
off-isolation and special C/P circuitry of the audio
switches eliminates click and pops in the head-phones
when the audio CODEC drivers are powering up/down
or when a headphone is inserted or removed from the
jack.
• -3dB Bandwidth USB Switch . . . . . . . . . . . . 700MHz
• Low ON Capacitance @ 240MHz. . . . . . . . . . . 4.2pF
• Available in µTQFN and TDFN Packages
• Compliant with USB 2.0 Short Circuit Requirements
Without Additional External Components
It’s available in a tiny 10 Ld 1.8mmx1.4mm ultra-thin
µTQFN package and a 10 Ld 3mmx3mm TDFN package.
It operates over a temperature range of -40°C to +85°C.
• Pb-Free (RoHS Compliant)
Related Literature
• MP3 and other Personal Media Players
(see page 19)
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
Applications*
(see page 19)
• Cellular/Mobile Phones
• PDA’s
• Audio/USB Switching
• Application Note AN1407 “ISL54210EVAL1Z
Evaluation Board User’s Manual”
Application Block Diagram
µCONTROLLER
3.3V
VDD
ISL54210
USB/HEADPHONE JACK
VBUS
VBUS
LOGIC CONTROL
4MΩ
4MΩ
D-
COM -
1
USB HIGH-SPEED
TRANSCEIVER
D+
200kΩ
COM +
200kΩ
CLICK
AND
POP
GND
March 18, 2010
FN6661.2
CTRL
R
L
AUDIO CODEC
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2008, 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL54210
MP3/USB 2.0 High Speed Switch with Negative
Signal Handling/Click and Pop Suppression
ISL54210
Pin Configurations
(Note 1)
ISL54210
(10 LD 3.0mmx3.0mm TDFN)
TOP VIEW
ISL54210
(10 LD 1.8mmx1.4mm µTQFN)
TOP VIEW
CTRL
VDD
8
9
10
L
7
6
CLICK/POP
LOGIC CONTROL
D-
D+
5
4
R
GND
VDD
1
VBUS
2
COM -
3
PD
4MΩ
4MΩ
LOGIC
CONTROL
10
CTRL
9
D-
8
D+
7
L
6
R
200kΩ
3
COM +
COM +
200kΩ
GND
1
4
5
CLICK/
POP
2
VBUS
COM -
NOTE:
1. Switches Shown for VBUS = Logic “0” and CTRL = Logic “1”.
Truth Table
Pin Descriptions
ISL54210
ISL54210
µTQFN TDFN NAME
FUNCTION
VBUS
CTRL
L, R
D+, D-
0
0
OFF
OFF
1
2
VBUS
Digital Control Input
2
3
COM-
Voice and Data Common Pin
3
4
COM+ Voice and Data Common Pin
4
5
GND
5
6
R
Audio Right Input
6
7
L
Audio Left Input
7
8
D+
USB Differential Input
8
9
D-
USB Differential Input
0
1
ON
OFF
1
X
OFF
ON
CTRL: Logic “0” when ≤ 0.5V or Floating, Logic “1” when ≥
1.4V
VBUS: Logic “0” when ≤ VDD + 0.2V or Floating, Logic “1”
when ≥ VDD + 0.8V
2
Ground Connection
9
10
CTRL
Digital Control Input (Audio Enable)
10
1
VDD
Power Supply
-
PD
PD
Thermal Pad. Tie to Ground or Float
FN6661.2
March 18, 2010
ISL54210
Ordering Information
PART NUMBER
(Note 5)
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL54210IRTZ (Note 3)
4210
-40 to +85
10 Ld 3mmx3mm TDFN
L10.3x3A
ISL54210IRTZ-T (Notes 2, 3)
4210
-40 to +85
10 Ld 3mmx3mm TDFN
L10.3x3A
ISL54210IRUZ-T (Notes 2, 4)
0
-40 to +85
10 Ld 1.8mmx1.4mm µTQFN
L10.1.8x1.4A
ISL54210EVAL1Z
Evaluation Board
NOTES:
2. Please refer to TB347 for details on reel specifications.
3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach
materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both
SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
4. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach
materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free
soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020.
5. For Moisture Sensitivity Level (MSL), please see device information page for ISL54210. For more information on MSL please
see techbrief TB363.
3
FN6661.2
March 18, 2010
ISL54210
Absolute Maximum Ratings
Thermal Information
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 5.5V
Input Voltages
D+, D-, L, R (Note 6). . . . . . . . . . . -2V to ((VDD) + 0.3V)
VBUS (Note 6) . . . . . . . . . . . . . . . . . . . . . . . -2V to 5.5V
CTRL (Note 6) . . . . . . . . . . . . . . -0.3V to ((VDD) + 0.3V)
Output Voltages
COM-, COM+ (Note 6) . . . . . . . . . . -2V to ((VDD) + 0.3V)
Continuous Current (Audio Switches) . . . . . . . . . . ±150mA
Peak Current (Audio Switches)
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . ±300mA
Continuous Current (USB Switches) . . . . . . . . . . . . ±40mA
Peak Current (USB Switches)
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . ±100mA
ESD Rating:
Human Body Model, COM Pins. . . . . . . . . . . . . . . . . >6kV
Human Body Model, All Pins . . . . . . . . . . . . . . . . . . >4kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . >300V
Charged Device Model . . . . . . . . . . . . . . . . . . . . . >1.5kV
Latch-up Tested per JEDEC; Class II Level A . . . . . at +85°C
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
10 Ld µTQFN Package (Notes 8, 10)
160
105
10 Ld 3x3 TDFN Package (Notes 7, 9) 55
18
Maximum Junction Temperature (Plastic Package). . +150°C
Maximum Storage Temperature Range. . . . . -65°C to +150°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact
product reliability and result in failures not covered by warranty.
NOTES:
6. Signals on D+, D-, L, R, COM-, COM+, CTRL, VBUS exceeding VDD or GND by specified amount are clamped. Limit current to
maximum current ratings.
7. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach”
features. See Tech Brief TB379.
8. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief
TB379 for details.
9. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
10. For θJC, the “case temp” location is taken at the package top center.
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V,
VCTRLH = 1.4V, VCTRLL = 0.5V, (Note 11), Unless Otherwise Specified.
Boldface limits apply over the operating temperature range,
-40°C to +85°C.
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 12, 13)
TYP
MAX
(Notes 12, 13) UNITS
ANALOG SWITCH CHARACTERISTICS
Audio Switches (L, R)
Analog Signal Range,
VANALOG
VDD = 2.7V to 3.6V, VBUS = float,
CTRL = 1.4V
Full
-1.5
-
1.5
V
ON-Resistance, rON
VDD = 3.0V, VBUS = 3.2V,
CTRL = 1.4V, ICOMx = 40mA, VL or
VR = -0.85V to 0.85V
(see Figure 2, Note 15)
+25
-
2.4
2.8
Ω
Full
-
-
3.8
Ω
rON Matching Between
Channels, ΔrON
VDD = 3.0V, VBUS = 3.2V,
CTRL = 1.4V, ICOMx = 40mA, VL or
VR = Voltage at max rON over signal
range of -0.85V to 0.85V
(Notes 15, 16)
+25
-
0.1
0.32
Ω
Full
-
-
0.4
Ω
rON Flatness, RFLAT(ON)
+25
VDD = 3.0V, VBUS = 3.2V,
CTRL = 1.4V, ICOMx = 40mA, VL or
Full
VR = -0.85V to 0.85V, (Notes 14, 15)
-
0.02
0.06
Ω
-
-
0.07
Ω
Insertion Loss, GON
VDD = 3.0V, VBUS = 0V, CTRL = VDD,
RLOAD = 32Ω
+25
-
-0.78
-
dB
Insertion Loss, GON
VDD = 3.0V, VBUS = 0V, CTRL = VDD,
RLOAD = 15Ω
+25
-
-1.5
-
dB
4
FN6661.2
March 18, 2010
ISL54210
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V,
VCTRLH = 1.4V, VCTRLL = 0.5V, (Note 11), Unless Otherwise Specified.
Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 12, 13)
TYP
MAX
(Notes 12, 13) UNITS
VDD = 3.6V, VBUS = 3.2V,
CTRL = 0.5V, VCOM- or VCOM+ =
-0.85V, 0.85V, VL or VR = -0.85V,
0.85V, VD+ and VD- = floating;
measure current through the
discharge pull-down resistor and
calculate resistance value.
+25
-
40
-
Ω
Analog Signal Range,
VANALOG
VDD = 2.7V to 3.6V, VBUS = 5.0V,
CTRL = 0V or VDD
Full
0
-
VDD
V
ON-Resistance, rON
VDD = 3.3V, VBUS = 4.4V,
CTRL = 1.4V, ICOMx = 1mA, VD+ or
VD- = 3.3V (see Figure 3, Note 15)
+25
-
25
35
Ω
Full
-
-
40
Ω
VDD = 3.3V, VBUS = 4.4V, CTRL = 0V
or VDD, ICOMx = 40mA, VD+ or
VD-= 0V to 400mV
(see Figure 3, Note 15)
25
-
5.4
6
Ω
Full
-
-
7.5
Ω
25
-
0.02
0.25
Ω
Full
-
-
0.25
Ω
Discharge Pull-Down
Resistance, RL, RR
USB Switches (D+, D-)
ON-Resistance, rON
rON Matching Between
Channels, ΔrON
VDD = 3.3V, VBUS = 4.4V, CTRL = 0V
or VDD, ICOMx = 40mA, VD+ or
VD-= Voltage at max rON
(Notes 15, 16)
rON Flatness, RFLAT(ON)
VDD = 3.3V, VBUS = 4.4V, CTRL = 0V
or VDD, ICOMx = 40mA, VD+ or
VD-= 0V to 400mV (Notes 14, 15)
25
-
0.45
0.55
Ω
Full
-
-
0.6
Ω
OFF Leakage Current,
ID+(OFF) or ID-(OFF)
VDD = 3.6V, VBUS = 0V, CTRL = 3.6V,
VCOM- or VCOM+ = 0.5V, 0V, VD+ or
VD- = 0V, 0.5V, VL and VR = float
25
-10
4
10
nA
Full
-50
-
50
nA
ON Leakage Current, IDX
VDD = 3.6V, VBUS = 5.25V, CTRL
= 0V or VDD, VD+ or VD- = 2.7V,
VCOM- or VCOM+ = Float, VL and
VR = float; measuring current
through 200k resistor at COM side
25
-20
11
20
µA
Full
-30
-
30
µA
DYNAMIC CHARACTERISTICS
USB Turn-ON Time, tON
VDD = 2.7V, RL = 50Ω, CL = 10pF
(see Figure 1)
25
-
43
-
ns
USB Turn-OFF Time, tOFF
VDD = 2.7V, RL = 50Ω, CL = 10pF
(see Figure 1)
25
-
14.5
-
ns
Audio Turn-ON Time, tON
VDD = 2.7V, RL = 50Ω, CL = 10pF
(see Figure 1)
25
-
7.5
-
µs
Audio Turn-OFF Time, tOFF
VDD =2.7V, RL = 50Ω, CL = 10pF
(see Figure 1)
25
-
130
-
ns
Skew, tSKEW
VDD = 3.0V, VBUS = 5.0V, CTRL = 0V
or 3V, RL = 45Ω, CL = 10pF, tR = tF =
750ps at 480Mbps,
(Duty Cycle = 50%) (see Figure 6)
25
-
50
-
ps
Total Jitter, tJ
VDD =3.0V, VBUS = 5.0V, CTRL = 0V
or 3V, RL = 50Ω, CL = 10pF, tR = tF =
750ps at 480Mbps
25
-
210
-
ps
Propagation Delay, tPD
VDD = 3.0V, VBUS = 5.0V, CTRL = 0V
or 3V, RL = 45Ω, CL = 10pF
(see Figure 6)
25
-
250
-
ps
5
FN6661.2
March 18, 2010
ISL54210
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V,
VCTRLH = 1.4V, VCTRLL = 0.5V, (Note 11), Unless Otherwise Specified.
Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 12, 13)
TYP
MAX
(Notes 12, 13) UNITS
25
-
-100
-
dB
Crosstalk
VDD = 3.0V, RL = 50Ω, f = 100kHz
(Audio to USB, USB to Audio) (see Figure 5)
25
-
-100
-
dB
Audio Crosstalk
R to COM-, L to COM+
VDD = 3.0V, VBUS = float,
CTRL = 3.0V, RL = 32Ω, f = 20Hz to
20kHz, VR or VL = 0.707VRMS (2VP-P)
(see Figure 5)
OFF-Isolation
VDD = 3.0V, RL = 50Ω, f = 100kHz
25
-
95
-
dB
OFF-Isolation
VDD = 3.0V, RL = 15Ω, f = 20Hz to
20kHz
25
-
111
-
dB
OFF-Isolation
VDD = 3.0V, RL = 32Ω, f = 20Hz to
20kHz
25
-
105
-
dB
OFF-Isolation
VDD = 3.0V, RL = 1kΩ, f = 20Hz to
20kHz
25
-
75
-
dB
OFF-Isolation
VDD = 3.0V, RL = 10kΩ, f = 20Hz to
20kHz
25
-
57
-
dB
OFF-Isolation
VDD = 3.0V, RL = 100kΩ, f = 20Hz to
20kHz
25
-
45
-
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, VDD = 3.0V, VBUS
= Float, CTRL = 3.0V, VL or
VR = 180mVRMS (509mVP-P)
RL = 32Ω
25
-
0.014
-
%
Total Harmonic Distortion
f = 20Hz to 20kHz, VDD = 3.0V, VBUS
= Float, CTRL = 3.0V, VL or
VR = 0.707VRMS (2VP-P), RL = 32Ω
25
-
0.056
-
%
Total Harmonic Distortion
f = 20Hz to 20kHz, VDD = 3.0V, VBUS
= 0V, CTRL = 3.0V, VL or
VR = 180mVRMS (509mVP-P),
RL = 15Ω
25
-
0.043
-
%
Total Harmonic Distortion
f = 20Hz to 20kHz, VDD = 3.0V,
VBUS = 0V, CTRL = 3.0V, VL or
VR = 0.707VRMS (2VP-P), RL = 15Ω
25
-
0.19
-
%
Click and Pop
VDD = 3.3V, CTRL = 0V, VBUS = float,
RL = 1kΩ, VL or VR = 0 to 1.25V
DC step or 1.25V to 0V DC step
(see Figure 7)
25
-
60
-
µVp
Click and Pop
VDD = 3.3V, CTRL = 0.5Hz square
wave, VBUS = float, RL = 1kΩ, VL or
VR = AC-coupled to ground
(see Figure 8)
25
-
500
-
µVp
USB Switch -3dB Bandwidth Signal = 0dBm, 0.2VDC offset,
RL = 50Ω, CL = 5pF
25
-
700
-
MHz
D+/D- OFF Capacitance,
CD+OFF, CD-OFF
f = 1MHz, VDD = 3.0V, VBUS = float,
CTRL = 3.0V, VD- or VD+ = VCOMx =
0V (see Figure 4)
25
-
4
-
pF
COM ON Capacitance,
CCOM-(ON), CCOM+(ON)
f = 1MHz, VDD = 3.0V, VBUS = 5.0V,
CTRL = 0V, VD- or VD+ = VCOMx = 0V
(see Figure 4)
25
-
9
-
pF
COM ON Capacitance,
CCOM-(ON), CCOM+(ON)
f = 240MHz, VDD = 3.0V,
VBUS = 5.0V, CTRL = 0V, VD- or
VD+ = VCOMx = 0V (see Figure 4)
25
-
4.2
-
pF
6
FN6661.2
March 18, 2010
ISL54210
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VBUSH = 3.8V, VBUSL = 3.2V,
VCTRLH = 1.4V, VCTRLL = 0.5V, (Note 11), Unless Otherwise Specified.
Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Notes 12, 13)
TYP
MAX
(Notes 12, 13) UNITS
POWER SUPPLY CHARACTERISTICS
Full
Power Supply Range, VDD
Positive Supply Current, IDD VDD = 3.6V, VBUS = 0V, CTRL = 3.6V
(Audio Mode)
Positive Supply Current, IDD VDD = 3.6V, VBUS = 5.25V,
CTRL = 3.6V
(USB Mode)
2.7
-
3.6
V
25
-
7
10
µA
Full
-
-
12
µA
25
-
2.4
4
µA
Full
-
-
5
µA
Positive Supply Current, IDD VDD = 3.6V, VBUS = 0V, CTRL = 0V
(Mute Mode)
25
-
2.4
4
µA
Full
-
-
5
µA
VBUS Current, IVBUS
25
-
-
1
µA
VDD = 2.7V to 3.6V
Full
-
-
VDD + 0.2V
V
VDD = 0V, VBUS = 5.25V,
CTRL = Float
DIGITAL INPUT CHARACTERISTICS
VBUS Voltage Low, VVBUSL
VBUS Voltage High, VVBUSH VDD = 2.7V to 3.6V
Full
VDD + 0.8V
-
-
V
CTRL Voltage Low, VCTRLL
VDD = 2.7V to 3.6V
Full
-
-
0.5
V
CTRL Voltage High, VCTRLH
VDD = 2.7V to 3.6V
Full
1.4
-
-
V
Input Current, IVBUSL,
ICTRLL
VDD = 3.6V, VBUS= 0V or float,
CTRL = 0V or Float
Full
-50
2
50
nA
Input Current, IVBUSH
VDD = 3.6V, VBUS = 5.25V,
CTRL = 0V or float
Full
-2
1
2
µA
Input Current, ICTRLH
VDD = 3.6V, VBUS = 0V or float,
CTRL = 3.6V
Full
-2
1
2
µA
VBUS Pull-Down Resistor,
RVBUS
VDD = 3.6V, VBUS = 5.25V,
CTRL = 0V or float, measure current
through the internal pull-down
resistor and calculate resistance
value.
Full
-
4
-
MΩ
CTRL Pull-Down Resistor,
RCTRL
VDD = 3.6V, VBUS = 0V or float,
CTRL = 3.6V, measure current
through the internal pull-down
resistor and calculate resistance
value.
Full
-
4
-
MΩ
NOTES:
11. VLOGIC = Input voltage to perform proper function.
12. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum.
13. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established
by characterization and are not production tested.
14. Flatness is defined as the difference between maximum and minimum value of ON-resistance over the specified analog signal
range.
15. Limits established by characterization and are not production tested.
16. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel
with lowest max rON value, between L and R or between D+ and D-.
7
FN6661.2
March 18, 2010
ISL54210
Test Circuits and Waveforms
VBUSH
LOGIC
INPUT
VBUSL
50%
CTRL
VINPUT
tOFF
SWITCH
INPUT VINPUT
SWITCH
INPUT
VOUT
AUDIO OR USB
COMx
VBUS
VOUT
90%
SWITCH
OUTPUT
C
VDD
tr < 20ns
tf < 20ns
90%
VBUS
CL
10pF
RL
50W
GND
0V
tON
Logic input waveform is inverted for switches that have the opposite logic
sense.
FIGURE 1A. MEASUREMENT POINTS
Repeat test for all switches. CL includes fixture and stray
capacitance.
RL
V OUT = V (INPUT) -----------------------R L + r ON
FIGURE 1B. TEST CIRCUIT
FIGURE 1. SWITCHING TIMES
VDD
VDD
C
C
rON = V1 / Icom
rON = V1/40mA
CTRL
D- OR D+
CTRL
L OR R
VD- OR D+
VL OR R
VBUS
V1
40mA
VBUSL
VBUS
V1
ICOM
COMx
VBUSH
COMx
GND
GND
REPEAT TEST FOR ALL SWITCHES
REPEAT TEST FOR ALL SWITCHES
FIGURE 2. AUDIO rON TEST CIRCUIT
VDD
FIGURE 3. USB rON TEST CIRCUIT
VDD
C
CTRL
CTRL
AUDIO OR USB
SIGNAL
GENERATOR
L OR R
VBUS
IMPEDANCE
ANALYZER
COMx
32Ω
VBUS
VBUSL OR
VBUSH
COMx
C
0V OR FLOAT
GND
R OR L
COMx
ANALYZER
NC
GND
RL
REPEAT TEST FOR ALL SWITCHES
REPEAT TEST FOR ALL SWITCHES
FIGURE 4. CAPACITANCE TEST CIRCUIT
8
FIGURE 5. AUDIO CROSSTALK TEST CIRCUIT
FN6661.2
March 18, 2010
ISL54210
Test Circuits and Waveforms (Continued)
VDD
C
tri
90%
DIN+
10%
CTRL
50%
VBUSH
VBUS
tskew_i
15.8Ω
DIN90%
DIN+
50%
COM+
143Ω
10%
15.8Ω
tfi
tro
CL
COM-
DIN-
OUT+
D+
OUT-
DCL
143Ω
45Ω
45Ω
90%
10%
50%
OUT+
OUT-
GND
tskew_o
|tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals.
50%
90%
|tfo - tfi| Delay Due to Switch for Falling Input and Falling Output Signals.
10%
tf0
|tskew_0| Change in Skew through the Switch for Output Signals.
|tskew_i| Change in Skew through the Switch for Input Signals.
FIGURE 6B. TEST CIRCUIT
FIGURE 6A. MEASUREMENT POINTS
FIGURE 6. SKEW TEST
3.3V
AUDIO PRECISION
SYSTEM II CASCADE
ANALYZER
FLOAT
CHA
VBUS
CHB
COM-
VDD
CLICK
AND
POP
COM+
L
R
RLOAD
RLOAD
GND
CTRL
0V TO 1.25V
DC STEP OR
1.25V TO 0V
DC STEP
SET AUDIO ANALYZER FOR PEAK DETECTION, 32 SAMPLES/SEC, A WEIGHTED FILTER, MANUAL RANGE 1X/Y, UNITS TO DBV
FIGURE 7. CLICK AND POP TEST CIRCUIT
9
FN6661.2
March 18, 2010
ISL54210
Test Circuits and Waveforms (Continued)
3.3V
AUDIO PRECISION
SYSTEM II CASCADE
ANALYZER
CHA
FLOAT
VBUS
CHB
C
VDD
COM-
L
CLICK
AND
POP
COM+
RLOAD
R
RLOAD
CTRL
GND
0V TO VDD
SQUARE WAVE
SET AUDIO ANALYZER FOR PEAK DETECTION, 32 SAMPLES/SEC, A WEIGHTED FILTER, MANUAL RANGE 1X/Y, UNITS TO DBV
FIGURE 8. CLICK AND POP TEST CIRCUIT
0V TO 3.0V
DC STEP OR
3.0V TO 0V
DC STEP
1Hz
VDD
L
COMCLICK
AND
POP
COM+
220µF
R
20kΩ
220µF
20kΩ
1.5V OR 0V
GND
VBUS CTRL
POWER SUPPLY TURN-ON/TURN-OFF CLICK AND POP TRANSIENT TEST
FIGURE 9. CLICK AND POP TEST CIRCUIT #2
10
FN6661.2
March 18, 2010
ISL54210
Typical Application Block Diagram
3.3V
VDD
ISL54210
VBUS
CTRL
µCONTROLLER
LOGIC CONTROL
USB/HEADPHONE JACK
VBUS
4MΩ
4MΩ
DCOM D+
200kΩ
USB
HIGH-SPEED
TRANSCEIVER
COM +
200kΩ
CLICK
AND
POP
R
L
AUDIO
CODEC
GND
Detailed Description
The ISL54210 device is a dual single pole/double throw
(SPDT) analog switch that operates from a single DC
power supply in the range of 2.7V to 3.6V. It was
designed to function as a dual 2-to-1 multiplexer to
select between USB differential data signals and audio L
and R stereo signals. It comes in tiny µTQFN and TDFN
packages for use in MP3 players, PDAs, cellphones, and
other personal media players.
The part consists of two 2.5Ω audio switches and two
5.5Ω USB switches. The audio switches can accept
signals that swing below ground. They were designed to
pass audio left and right stereo signals, that are ground
referenced, with minimal distortion. The USB switches
were designed to pass high-speed USB differential data
signals with minimal edge and phase distortion.
The ISL54210 was specifically designed for MP3 players,
personal media players and cellphone applications that
need to combine the audio headphone jack and the USB
data connector into a single shared connector, thereby
saving space and component cost. A “Typical Application
Block Diagram” of this functionality is shown on page 11.
The ISL54210 incorporates circuitry for the detection of
the USB VBUS voltage, which is used to switch between
the audio CODEC drivers and USB transceiver of the MP3
player or cellphone. The ISL54210 contains a logic
control pin (CTRL) that when driven low while VBUS is
low, opens all switches and activates the audio click and
pop circuitry.
A detailed description of the two types of switches are
provided in the following sections. In a typical
application, the USB transmission and audio playback are
intended to be mutually exclusive operations.
11
Audio Switches
The two audio switches (L, R) are 2.5Ω switches that can
pass signals that swing below ground. Crosstalk between
the audio switches is <-100dB over the audio band.
These switches have excellent off-isolation >105dB over
the audio band with a 32Ω load.
Over a signal range of ±1V (0.707VRMS) with
VDD > 2.7V, these switches have an extremely low rON
resistance variation. They can pass ground referenced
audio signals with very low distortion (<0.06% THD+N)
when delivering 15.6mW into a 32Ω headphone speaker
load. See Figures 16, 17, 18, and 19 THD+N in “Typical
Performance Curves” beginning on page 14.
The audio drivers should be connected at the L and R
side of the switch (pins 5 and 6 for µTQFN, pins 6 and 7
for TDFN) and the speaker loads should be connected at
the COM side of the switch (pins 2 and 3 for µTQFN, pins
3 and 4 for TDFN).
The audio switches have click and pop circuitry on the L
and R side that is activated when the VBUS voltage is ≤
VDD + 0.2V or floating and the CTRL voltage ≤ to 0.5V or
floating. The ISL54210 should be put in this mode before
powering down or powering up of the audio CODEC
drivers. In this mode, both the audio and USB in-line
switches will be OFF and the audio click and pop circuitry
will be ON. The high off-isolation of the audio switches
along with the click and pop circuitry will isolate the
transients generated during power-up and power-down
of the audio CODECs from getting through to the
headphones, thus eliminating click and pop noise in the
headphones.
The audio switches are active (turned ON) whenever the
VBUS voltage is ≤ VDD + 0.2V or floating and the CTRL
voltage ≥ to 1.4V.
FN6661.2
March 18, 2010
ISL54210
USB Switches
or tri-stated. The CTRL control pin is only active when
VBUS is logic “0”.
The two USB switches (D+, D-) are 5.5Ω bidirectional
switches that were specifically designed to pass
high-speed USB differential signals typically in the range
of 0V to 400mV. The switches have low capacitance and
high bandwidth to pass USB high-speed signals
(480Mbps) with minimum edge and phase distortion to
meet USB 2.0 signal quality specifications. See Figure 20
for high-speed eye pattern taken with switch in the signal
path.
VBUS = Logic “0” (Low) when VBUS ≤ VDD + 0.2V or
Floating.
VBUS = Logic “1” (High) when VBUS ≥ VDD + 0.8V
CTRL = Logic “0” (Low) when ≤ 0.5V or Floating.
CTRL = Logic “1” (High) when ≥ 1.4V
These switches can also swing rail-to-rail and pass USB
full-speed signals (12Mbps) with minimal distortion. See
Figure 21 for full-speed eye pattern taken with switch in
the signal path.
If the VBUS pin = Logic “0” and CTRL pin = Logic “1”, the
part will be in the Audio mode. In Audio mode, the L
(left) and R (right) 2.5Ω audio switches are ON, the Dand D+ 5.5Ω switches are OFF (high impedance) and the
audio click and pop circuitry is OFF (high impedance).
The maximum signal range for the USB switches is from
-1.5V to VDD. The signal voltage at D- and D+ should not
be allowed to exceed the VDD voltage rail or go below
ground by more than -1.5V.
The USB switches are active (turned ON) whenever the
VBUS voltage is ≥ to VDD + 0.8V. VBUS is internally pulled
low, so when VBUS is floating the USB switches are OFF.
ISL54210 Operation
The following discusses using the ISL54210 in the
“Typical Application Block Diagram” on page 11.
VDD SUPPLY
The DC power supply connected at VDD (Pin 10 for
µTQFN, Pin 1 for TDFN) provides the required bias
voltage for proper switch operation. Its voltage should be
kept in the range of 2.7V to 3.6V when used in a
USB/Audio application to ensure you get proper
switching when the VBUS voltage is at its lower limit of
4.4V.
In a typical USB/Audio application for portable battery
powered devices, the VDD voltage will come from a
battery or an LDO and be in the range of 2.7V to 4.3V.
For best possible USB full-speed operation (12Mbps), it is
recommended that the VDD voltage be ≥2.7V in order to
get a USB data signal level above 2.7V.
Before power-up and power-down of the ISL54210 part,
the VBUS and CTRL control pins should be driven to
ground or tri-stated. This will put the switch in the mute
state which turns all switches OFF and activates the click
and pop circuitry. Which will minimize transients at the
speaker loads during power-up and power-down.
LOGIC CONTROL
The state of the ISL54210 device is determined by the
voltage at the VBUS pin (Pin 1 for µTQFN, Pin 2 for TDFN)
and the CTRL pin (Pin 9 for µTQFN, Pin 10 for TDFN). The
part has three states or modes of operation: Audio Mode,
USB Mode and Mute Mode. Refer to the “Truth Table” on
page 2.
The VBUS pin and CTRL pin are internally pulled low
through 4MΩ resistors to ground and can be left floating
12
Logic Control Voltage Levels:
Audio Mode
In a typical application, VDD will be in the range of 2.7V
to 3.6V and will be connected to the battery or LDO of
the MP3 player or cellphone. When a headphone is
plugged into the common connector, nothing gets
connected at the VBUS pin (its internally pulled low) and
as long as the CTRL = Logic “1” the ISL54210 part
remains in the audio mode and the audio drivers of the
player can drive the headphones and play music.
USB Mode
If the VBUS pin = Logic “1” and CTRL pin = Logic “0” or
Logic “1” the part will go into USB mode. In USB mode,
the D- and D+ 5.5Ω switches are ON and the L and R
2.5Ω audio switches are OFF (high impedance).
When a USB cable from a computer or USB hub is
connected at the common connector, the voltage at the
VBUS pin will be driven with the USB VBUS voltage which
will be in the range of 4.4V to 5.25V. The ISL54210 part
will go into the USB mode. In USB mode, the computer
or USB hub transceiver and the MP3 player or cellphone
USB transceiver are connected and digital data will be
able to be transmitted back and forth.
When the USB cable is disconnected the ISL54210
automatically turns the D+ and D- switches OFF.
Mute Mode
If the VBUS pin = Logic “0” and CTRL pin = Logic “0”, the
part will be in the Mute mode. In the Mute mode, the
audio switches and the USB switches are OFF (high
impedance) and the audio click and pop circuitry is ON.
Before powering down or powering up of the audio
CODECs drivers, the ISL54210 should be put in the Mute
mode. In Mute mode transients present at the L and R
signal pins due to the changing DC voltage of the audio
drivers will not pass to the headphones preventing clicks
and pops in the headphones. See “AC-Coupled click and
pop operation” on page 13.
Before power-up and power-down of the ISL54210 part,
the VBUS and CTRL control pins should be driven to
ground or tri-stated. This will put the switch in the mute
state, which turns all switches OFF and activates the click
and pop circuitry. This will minimize transients at the
FN6661.2
March 18, 2010
ISL54210
speaker loads during power-up and power-down. See
Figure 30 in the “Typical Performance Curves” on
page 18.
AC-COUPLED CLICK AND POP OPERATION
Single supply audio drivers have their signal biased at a
DC offset voltage (usually at 1/2 the DC supply voltage of
the driver). As this DC bias voltage comes up or goes
down during power-up or power-down of the driver, a
transient can be coupled into the speaker load through
the DC blocking capacitor (see the“Typical Application
Block Diagram” on page 11).
When a driver is OFF and then turned ON, the rapidly
changing DC bias voltage at the output of the driver will
cause an equal voltage at the input side of the switch due
to the fact that the voltage across the blocking capacitor
cannot change instantly. If the switch is in the Audio
mode or there is no low impedance path to discharge the
blocking capacitor voltage at the input of the switch,
before turning on the audio switch, a transient discharge
will occur in the speaker, generating a click/pop noise.
Typical Performance Curves
2.70
Proper elimination of a click/pop transient at the
speaker loads while powering up or down of the audio
drivers requires that the ISL54210 have its click/pop
circuitry activated by putting the part in the Mute
mode. This allows the transients generated by the
audio drivers to be discharged through the click and
pop shunt circuitry.
Once the driver DC bias has reached VDD/2 and the
transient on the switch side of the DC blocking capacitor
has been discharged to ground through the click/pop
shunt circuitry, the audio switches can be turned ON and
connected through to the speaker loads without
generating any undesirable click/pop noise in the
speakers.
With a typical DC blocking capacitor of 220µF and the
click/pop shunt circuitry designed to have a resistance
of 20Ω to 70Ω, allowing a 100ms wait time to discharge
the transient before placing the switch in the Audio
mode will prevent the transient from getting through
to the speaker load. See Figures 28 and 29 in the
“Typical Performance Curves” page 17.
TA = +25°C, Unless Otherwise Specified
4.0
ICOM = 40mA
ICOM = 40mA
VDD = 3.0V
3.6
VDD = 2.5V
VDD = 3.6V
rON (Ω)
rON (Ω)
2.65
VDD = 3.3V
2.60
VDD = 4.3V
3.2
2.8
VDD = 2.7V
VDD = 3.6V
2.55
2.4
2.50
-1.5
-1.0
-0.5
0
0.5
1.0
VCOM (V)
FIGURE 10. AUDIO ON-RESISTANCE vs SUPPLY
VOLTAGE vs SWITCH VOLTAGE
13
1.5
2.0
-1.5
-1.0
-0.5
0
VCOM (V)
0.5
1.0
1.5
FIGURE 11. AUDIO ON-RESISTANCE vs SUPPLY
VOLTAGE vs SWITCH VOLTAGE
FN6661.2
March 18, 2010
ISL54210
Typical Performance Curves
TA = +25°C, Unless Otherwise Specified (Continued)
25
4
VDD = 3.0V
+85°C
ICOM = 40mA
20
3
rON (Ω)
rON (Ω)
15
+25°C
10
2
+25°C
-40°C
5
VDD = 3.0V
ICOM = 40mA
1
-1.5
-1.0
-0.5
0
0.5
1.0
+85°C
-40°C
-1.0 -0.5
0
-1.5
1.5
0
0.5
1.0
VCOM (V)
VCOM (V)
1.5
2.0
2.5
3.0
FIGURE 13. AUDIO ON-RESISTANCE vs SWITCH
VOLTAGE vs TEMPERATURE
FIGURE 12. AUDIO ON-RESISTANCE vs SWITCH
VOLTAGE vs TEMPERATURE
7.0
7
VDD = 3.3V
ICOM = 40mA
ICOM = 40mA
6.5
+85°C
6
6.0
+25°C
VDD = 2.7V
5.5
VDD = 3.3V
5.0
rON (Ω)
rON (Ω)
5
VDD = 3.6V
4.5
-40°C
4
3
4.0
VDD = 5V
VDD = 4.3V
2
3.5
3.0
0
0.1
0.2
VCOM (V)
0.3
FIGURE 14. USB ON-RESISTANCE vs SUPPLY VOLTAGE
vs SWITCH VOLTAGE
0.058
1
0.4
0
0.1
0.2
VCOM (V)
0.3
0.4
FIGURE 15. USB ON-RESISTANCE vs SWITCH VOLTAGE
vs TEMPERATURE
RLOAD = 32Ω
VDD = 3V
PEAK-TO-PEAK VOLTAGES AT LOAD
0.08
VDD = 2.7V
3VP-P
0.056
THD+N (%)
THD+N (%)
2.5VP-P
VDD = 3.0V
VDD = 3.3V
0.054
VDD = 3.6V
0.052
20
2k
FREQUENCY (Hz)
1VP-P
510mVP-P
0.02
20k
FIGURE 16. THD+N vs SUPPLY VOLTAGE vs FREQUENCY
14
2VP-P
0.04
RLOAD = 32Ω
VLOAD = 0.707VRMS
200
0.06
20
200
2k
20k
FREQUENCY (Hz)
FIGURE 17. THD+N vs SIGNAL LEVELS vs FREQUENCY
FN6661.2
March 18, 2010
ISL54210
Typical Performance Curves
TA = +25°C, Unless Otherwise Specified (Continued)
0.14
0.30
RLOAD = 32Ω
FREQ = 1kHz
VDD = 3V
0.12
0.20
THD+N (%)
0.10
0.08
0.06
0.08
0.06
0.04
0.04
0.02
0.02
0
0.3
0.6
0.9
1.2
1.5
1.8
2.1
2.3
2.6
2.9
0
5
10
15
20
25
30
OUTPUT POWER (mW)
OUTPUT VOLTAGE (VP-P)
FIGURE 19. THD+N vs OUTPUT POWER
FIGURE 18. THD+N vs OUTPUT VOLTAGE
VDD = 3.3V
VOLTAGE SCALE (0.1V/DIV)
THD+N (%)
0.10
RLOAD = 32Ω
FREQ = 1kHz
VDD = 3V
TIME SCALE (0.2ns/DIV.)
FIGURE 20. EYE PATTERN: 480Mbps WITH USB SWITCHES IN THE SIGNAL PATH
15
FN6661.2
March 18, 2010
ISL54210
Typical Performance Curves
TA = +25°C, Unless Otherwise Specified (Continued)
VOLTAGE SCALE (0.5V/DIV)
VDD = 3.3V
TIME SCALE (10ns/DIV)
FIGURE 21. EYE PATTERN: 12Mbps USB SIGNAL WITH USB SWITCHES IN THE SIGNAL PATH
-60
-65
-70
CROSSTALK (dB)
-80
-85
-90
-95
-100
L TO R
-105
R TO L
-110
-115
5k
10k 20k
FIGURE 22. OFF-ISOLATION AUDIO SWITCHES vs
LOADING
16
VDD = 3V
RLOAD = 32Ω
VSIGNAL = 0.707VRMS
-75
OFF- ISOLATION (dB)
-40
-45
VDD = 3.3V
VSIGNAL = 0.707VRMS
-50
-55
RL = 10kΩ
-60
-65
-70
-75
RL = 1kΩ
-80
-85
-90
-95
-100
RL = 32Ω
-105
-110
-115
-120
20
50
100 200
500 1k
2k
FREQUENCY (Hz)
-120
20
50
100
200
500 1k
2k
FREQUENCY (Hz)
5k
10k 20k
FIGURE 23. AUDIO CHANNEL-TO-CHANNEL CROSSTALK
FN6661.2
March 18, 2010
ISL54210
Typical Performance Curves
TA = +25°C, Unless Otherwise Specified (Continued)
-60
0
VDD = 3V
RLOAD = 50Ω
VSIGNAL = 0.707VRMS
-70
-80
-20
NORMALIZED GAIN (dB)
-90
CROSSTALK (dB)
-100
USB TO AUDIO
-110
-120
-130
AUDIO TO USB
-140
RL = 50Ω
VSIGNAL = 0.2VP-P to 2VP-P
-150
-160
-40
-60
-80
-100
-120
-170
-180
20
50
100 200
500 1k 2k
5k
FREQUENCY (Hz)
10k 20k
50k 100k
-140
0.001
0
10M
100M
500M
1
USB SWITCH
RL = 50Ω
VSIGNAL = 0.2VP-P to 2VP-P
0
-1
-20
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
0.1
1M
FREQUENCY (Hz)
FIGURE 25. OFF-ISOLATION USB SWITCHES
FIGURE 24. CHANNEL-TO-CHANNEL CROSSTALK
-10
0.01
-30
-40
-50
-60
-70
-2
-3
-4
RL = 50Ω
-80
VSIGNAL = 0.2VP-P TO 2VP-P
-90
-100
0.001
0.01
0.1
1M
FREQUENCY (Hz)
10M
100M
500M
1M
MUTE 2V/DIV
MUTE 2V/DIV
VDD/2 2V/DIV
VDD/2 2V/DIV
LIN 200mV/DIV
LOUT
50mV/DIV
TIME (s) 100ms/DIV
FIGURE 28. 32Ω AC-COUPLED CLICK AND POP
REDUCTION
17
1G
FIGURE 27. FREQUENCY RESPONSE
VOLTAGE (V)
VOLTAGE (V)
FIGURE 26. OFF-ISOLATION AUDIO SWITCHES
10M
100M
FREQUENCY (Hz)
LIN 200mV/DIV
LOUT
50mV/DIV
TIME (s) 100ms/DIV
FIGURE 29. 1kΩ AC-COUPLED CLICK AND POP
REDUCTION
FN6661.2
March 18, 2010
ISL54210
Typical Performance Curves
TA = +25°C, Unless Otherwise Specified (Continued)
VDD 1V/DIV
VOLTAGE (V)
Die Characteristics
SUBSTRATE AND TDFN THERMAL PAD
POTENTIAL (POWERED UP):
GND
TRANSISTOR COUNT:
VIN = 1.5V OR 0V
98
VBUS = CTRL = 0V
VOUT 10mV/DIV
PROCESS:
Submicron CMOS
TIME (s) 200ms/DIV
FIGURE 30. POWER-UP/POWER-DOWN CLICK AND
POP TRANSIENT
18
FN6661.2
March 18, 2010
ISL54210
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to
web to make sure you have the latest Rev.
DATE
REVISION
CHANGE
3/18/10
FN6661.2
Converted to New Intersil Template
Replaced note, page 3: “θJA is measured with the component mounted on a high effective thermal
conductivity test board in free air. See Tech Brief TB379 for details.” with “direct attached note”
Added “Boldface limits apply over the operating temperature range, -40°C to +85°C.” to
Electrical Specifications table.
On page 1 in “Related Literature” section added App Note AN1407.
On page 1 in “Features” section added “Low On Capacitance at 240MHz 4.2pF”
On page 2 added thermal pad (PD) to TDFN pinout and added PD column to “Pin Descriptions”
table.
Page 4 in “Abs Max Rating” section added HBM rating for COM pins of 6kV and Latchup level.
Thermal information Tjc for uTQFN changed from “61.9” to “105” and note for Tja was added
to reference no direct attach, added Tjc to show the case temp location at top center.
Page 4 in Electrical Spec Table - Removed Note Reference from Typical Column and Added to
specific specs in Audio Switches and USB Switches as follows: On Resistance, rON Matching
Between Channels and rON Flatness.
Page 6 in electrical specifications table added “On Capacitance at 240MHz parameter.
Page 15 Figure 20 Change from USB far end mask to USB near end mask.
Page 18 in “Die Characteristics” section added TDFN thermal pad potential.
1/6/09
FN6661.1
Corrected Order Information.
7/2/08
FN6661.0
Initial Release to web
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The
Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones,
handheld products, and notebooks. Intersil's product families address power management and analog signal
processing functions. Go to www.intersil.com/products for a complete list of Intersil product families.
*For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device
information page on intersil.com: ISL54210
To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff
FITs are available from our website at http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications
at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by
Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any
patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
19
FN6661.2
March 18, 2010
ISL54210
Thin Dual Flat No-Lead Plastic Package (TDFN)
L10.3x3A
2X
0.10 C A
A
10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
D
MILLIMETERS
2X
0.10 C B
SYMBOL
MIN
NOMINAL
MAX
NOTES
A
0.70
0.75
0.80
-
A1
-
-
0.05
-
E
A3
6
INDEX
AREA
TOP VIEW
B
//
A
C
SEATING
PLANE
0.08 C
b
0.20
0.25
0.30
5, 8
D
2.95
3.0
3.05
-
D2
2.25
2.30
2.35
7, 8
E
2.95
3.0
3.05
-
E2
1.45
1.50
1.55
7, 8
e
0.50 BSC
-
k
0.25
-
-
-
L
0.25
0.30
0.35
8
A3
SIDE VIEW
D2
(DATUM B)
0.10 C
0.20 REF
7
8
N
10
2
Nd
5
3
Rev. 4 8/09
D2/2
NOTES:
6
INDEX
AREA
1
2
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
NX k
3. Nd refers to the number of terminals on D.
(DATUM A)
4. All dimensions are in millimeters. Angles are in degrees.
E2
E2/2
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
NX L
N
N-1
NX b
8
e
(Nd-1)Xe
REF.
BOTTOM VIEW
5
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
0.10 M C A B
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
9. Compliant to JEDEC MO-229-WEED-3 except for D2
dimensions.
CL
NX (b)
(A1)
L1
5
9 L
( 2.30 )
e
SECTION "C-C"
C C
( 2.00 )
TERMINAL TIP
FOR ODD TERMINAL/SIDE
( 10X 0.50)
(1.50)
( 2.90 )
Pin 1
(8x 0.50)
( 10X 0.25)
TYPICAL RECOMMENDED LAND PATTERN
20
FN6661.2
March 18, 2010
ISL54210
Package Outline Drawing
L10.1.8x1.4A
10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 4, 9/09
(DATUM A)
1.80
A
PIN #1 ID
1
2
0.50
1.40
6
INDEX AREA
2X
B
NX 0.40
NX 0.20 5
10X
0.10 M C A B
0.05 M C
5
0.10 C
1
2X
(DATUM B)
7
2
0.10 C
0.40 BSC
BOTTOM VIEW
TOP VIEW
0.10 C
C
0.5
0.05 C
SEATING PLANE
0.05 MAX
2.20
1.00
0.60
1.00
SIDE VIEW
0.50
1.80
0.40
0.20
0.20
0.40
5
NX (0.20)
CL
(0.05 MAX)
0.127 REF
0.40
e
SECTION "C-C"
TYPICAL RECOMMENDED LAND PATTERN
TERMINAL TIP
C C
10 LAND PATTERN
0.40 BSC
DETAIL "X"
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals. Total 10 leads.
3. Nd and Ne refer to the number of terminals on D (4) and E (6) side,
respectively.
4. All dimensions are in millimeters. Tolerances ±0.05mm unless
otherwise noted. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Maximum package warpage is 0.05mm.
8. Maximum allowable burrs is 0.076mm in all directions.
9. JEDEC Reference MO-255.
10. For additional information, to assist with the PCB Land Pattern
Design effort, see Intersil Technical Brief TB389.
21
FN6661.2
March 18, 2010