ISL4486, ISL81486 UCT E PROD ENT PART T E L O OB S LACEM ED REP D N E M E R E C OM ISL3159 Data Sheet August 2004 5V, Ultra High Speed, PROFIBUS®, RS-485/RS-422 Transceivers Features • Specified for 10% Tolerance Supplies The Intersil ISL4486 and ISL81486 are BiCMOS, 5V powered, single transceivers that meet both the RS-485 and RS-422 standards for balanced communication, and feature the larger output voltage and higher data rate - up to 40Mbps - required by high speed PROFIBUS applications. Unlike competitive products, these Intersil devices are specified for 10% tolerance supplies (4.5V to 5.5V) and deliver at least a 2.3V differential output voltage over this supply range. At the 5% tolerance specified by many competitors, the ISL4486 delivers an unsurpassed 2.5V differential signal into a 54 total load. This translates into longer reach, or better data integrity, at the exceptional 40Mbps data rate. SCSI applications benefit from the ISL4486’s low receiver and transmitter part-to-part skews, which make it perfect for high speed parallel applications where large numbers of bits must be simultaneously captured. The low bit-to-bit skew eases the timing constraints on the data latching signal. These devices present a “0.6 unit load” to the RS-485 bus, which allows up to 50 transceivers on the network. Receiver (Rx) inputs feature a “fail-safe if open” design, which ensures a logic high Rx output if Rx inputs are floating. Driver (Tx) outputs are short circuit protected, even for voltages exceeding the power supply voltage. Additionally, on-chip thermal shutdown circuitry disables the Tx outputs to prevent damage if power dissipation becomes excessive. TEMP. RANGE (°C) • High Data Rates ISL4486 . . . . . . . . . . . . . . . . . . . . . . . . . . up to 40Mbps ISL81486 . . . . . . . . . . . . . . . . . . . . . . . . . up to 30Mbps • Large Differential Output Voltage . . . . . . . . . . 3V into 54 • Low Bit-to-Bit (Part-to-Part) Skew for Parallel Applications • 0.6 Unit Load Allows up to 50 Devices on the Bus • ISL81486 is a Drop-In Replacement for the ADM1486 • Low Quiescent Current . . . . . . . . . . . . . . . . . . . . . 800A • -7V to +12V Common Mode Input Voltage Range • Three-State Rx and Tx Outputs • 14ns (Max) Propagation Delays, 2ns (Max) Skew • Operates from a Single +5V Supply (10% Tolerance) • Current Limiting and Thermal Shutdown for driver Overload Protection • Pb-free available Applications • SCSI “Fast 40” Drivers and Receivers • PROFIBUS DP and FMS Networks • Factory Automation • Field Bus Networks • Security Networks • Building Environmental Control Systems Ordering Information PART NO. (BRAND) FN6060.2 PACKAGE PKG. DWG. # ISL4486IB (4486IB) -40 to 85 8 Ld SOIC M8.15 ISL4486IBZ (4486IB) (See Note) -40 to 85 8 Ld SOIC (Pb-free) M8.15 ISL4486IU (4486) -40 to 85 8 Ld MSOP M8.118 ISL4486IUZ (4486) (See Note) -40 to 85 8 Ld MSOP (Pb-free) M8.118 ISL81486IB (81486IB) -40 to 85 8 Ld SOIC M8.15 ISL81486IBZ (81486IB) (See Note) -40 to 85 8 Ld SOIC (Pb-free) M8.15 ISL81486IU (1486) -40 to 85 8 Ld MSOP M8.118 ISL81486IUZ (1486) (See Note) -40 to 85 8 Ld MSOP (Pb-free) M8.118 • Industrial/Process Control Networks Pinout ISL4486, ISL81486 (SOIC, MSOP) TOP VIEW RO 1 8 VCC RE 2 7 B/Z DE 3 6 A/Y 5 GND DI 4 R D *Add “-T” suffix to part number for tape and reel packaging. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas LLC Copyright © Intersil Americas LLC 2004. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL4486, ISL81486 Truth Table Truth Table TRANSMITTING RECEIVING INPUTS OUTPUTS INPUTS OUTPUT RE DE DI B/Z A/Y RE DE A-B RO X 1 1 0 1 0 0 +0.2V 1 X 1 0 1 0 0 0 -0.2V 0 X 0 X High-Z High-Z 0 0 Inputs Open 1 1 X X High-Z Pin Descriptions PIN FUNCTION RO Receiver output: If A > B by at least 0.2V, RO is high; If A < B by 0.2V or more, RO is low; RO = High if A and B are unconnected (floating). RE Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high. DE Driver output enable. The driver outputs, Y and Z, are enabled by bringing DE high. They are high impedance when DE is low. DI Driver input. A low on DI forces output Y low and output Z high. Similarly, a high on DI forces output Y high and output Z low. GND Ground connection. A/Y RS-485/422 level, noninverting receiver input and noninverting driver output. Pin is an input (A) if DE = 0; pin is an output (Y) if DE = 1. B/Z RS-485/422 level, inverting receiver input and inverting driver output. Pin is an input (B) if DE = 0; pin is an output (Z) if DE = 1. VCC System power supply input (4.5V to 5.5V). Typical Operating Circuit ISL4486 +5V +5V + 8 0.1F 0.1F + 8 VCC 1 RO VCC R D 2 RE B/Z 7 3 DE A/Y 6 4 DI RT RT 7 B/Z DE 3 6 A/Y RE 2 R D GND GND 5 5 2 DI 4 RO 1 ISL4486, ISL81486 Absolute Maximum Ratings Thermal Information VCC to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Input Voltages DI, DE, RE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V Input/Output Voltages A/Y, B/Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8V to +12.5V RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to (VCC +0.5V) Short Circuit Duration Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Thermal Resistance (Typical, Note 1) JA (°C/W) 8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . 105 8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . 140 Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (Lead Tips Only) Operating Conditions Temperature Range ISLXX86IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = 25°C, Note 2 PARAMETER TEMP (°C) MIN TYP MAX UNITS Full - - VCC V R = 50 (RS-422) (Figure 1A) Full 2.5 3.7 - V R = 27 (RS-485), VCC 4.75V (Figure 1A, ISL4486 Only) Full 2.5 3 5 V R = 27 (RS-485), VCC= 4.5V (Figure 1A) Full 2.3 - 5 V RD = 60, -7V VCM 12V, VCC 4.75V (Figure 1B) Full 2.4 - - V VOD R = 27 or 50, (Figure 1A) Full - 0.01 0.2 V VOC R = 27 or 50 (Figure 1A) Full - - 3 V VOC R = 27 or 50 (Figure 1A) Full - 0.01 0.2 V SYMBOL TEST CONDITIONS DC CHARACTERISTICS Driver Differential VOUT (no load) VOD1 Driver Differential VOUT (with load) VOD2 Change in Magnitude of Driver Differential VOUT for Complementary Output States Driver Common-Mode VOUT Change in Magnitude of Driver Common-Mode VOUT for Complementary Output States Logic Input High Voltage VIH DE, DI, RE Full 2 - - V Logic Input Low Voltage VIL DE, DI, RE Full - - 0.8 V Logic Input Current IIN1 DE, DI, RE Full -1 - 1 A Input Current (A/Y, B/Z) (Note 5) IIN2 DE = 0V, VCC = 0V or 4.5 to 5.5V Receiver Differential Threshold Voltage VTH VIN = 12V Full - - 0.6 mA VIN = -7V Full -0.35 - - mA -7V VCM 12V Full -0.2 - 0.2 V Receiver Input Hysteresis VTH VCM = 0V 25 - 40 - mV Receiver Output High Voltage VOH IO = -4mA, VID = 200mV Full 4 - - V Receiver Output Low Voltage VOL IO = -4mA, VID = 200mV Full - - 0.4 V Three-State (high impedance) Receiver Output Current IOZR 0.4V VO 2.4V Full - - 1 A Receiver Input Resistance RIN -7V VCM 12V (Note 7) Full 20 - - k No-Load Supply Current (Note 3) ICC DI, RE = 0V or VCC DE = VCC Full - 1 2 mA DE = 0V Full - 0.8 1.5 mA 3 ISL4486, ISL81486 Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = 25°C, Note 2 (Continued) PARAMETER SYMBOL TEST CONDITIONS TEMP (°C) MIN TYP MAX UNITS Driver Short-Circuit Current, VO = High or Low IOSD1 DE = VCC, -7V VY or VZ 12V (Note 4) Full 60 - 250 mA Receiver Short-Circuit Current IOSR 0V VO VCC Full 7 - 85 mA Full 3 9 14 ns Full 3 9 17 ns Full - 0 6 ns SWITCHING CHARACTERISTICS Driver Input to Output Prop Delay tPLH, tPHL RDIFF = 54, CL = 100pF (Figure 2) Prop Delay Delta, Min-to-Max tDP-PSKEW RDIFF = 54, CL = 100pF, ISL4486 Only (Note 6, Figure 2) Driver Prop Delay Skew tSKEW Driver Differential Rise or Fall Time tR, tF ISL4486 ISL81486 RDIFF = 54, CL = 100pF (Figure 2) Full - 0 2 ns RDIFF = 54, CL = 100pF (Figure 2) ISL4486 Full - 5 8 ns ISL81486 Full - 7 15 ns Full - 9 15 ns tZH CL = 50pF, SW = GND (Figure 3) Driver Enable to Output Low tZL CL = 50pF, SW = VCC (Figure 3) Full - 9 15 ns Matched Enable Switching |tAZH - tBZL| or |tBZH - tAZL| tEN At Identical Test Conditions (Figure 3) Full - 1 3 ns Driver Enable to Output High Driver Disable from Output High tHZ CL = 50pF, SW = GND (Figure 3) Full - 9 15 ns Driver Disable from Output Low tLZ CL = 50pF, SW = VCC (Figure 3) Full - 9 15 ns Matched Disable Switching |tAHZ - tBLZ| or |tBHZ - tALZ| tDIS At Identical Test Conditions (Figure 3) Full - 2 5 ns Driver Maximum Data Rate fMAXD VOD| 1.5V (Figure 4) ISL4486 Full 40 - - Mbps ISL81486 Full 30 - - Mbps ISL4486 Full 11 17 25 ns ISL81486 Full 6 17 25 ns Full - 0 9 ns Figure 5 Full - 0.5 3 ns Receiver Input to Output Prop Delay tPLH, tPHL Prop Delay Delta, Min-to-Max tRP-PSKEW ISL4486 Only (Note 6, Figure 5) Receiver Prop Delay Skew | tPLH - tPHL | tSKD (Figure 5) Receiver Enable to Output High tZH CL = 15pF, SW = GND (Figure 6) Full - 7 13 ns Receiver Enable to Output Low tZL CL = 15pF, SW = VCC (Figure 6) Full - 7 13 ns Receiver Disable from Output High tHZ CL = 15pF, SW = GND (Figure 6) Full - 7 13 ns tLZ CL = 15pF, SW = VCC (Figure 6) Full - 7 13 ns CL = 15pF, VID 1.5V, RO tH and tL 20ns Full 40 - - Mbps Receiver Disable from Output Low Receiver Maximum Data Rate fMAXR NOTES: 2. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. 3. Supply current specification is valid for loaded drivers when DE = 0V. 4. Applies to peak current. See “Typical Performance Curves” for more information. 5. Devices meeting these limits are denoted as “0.6 unit load (UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus, so a 0.6UL transceiver permits > 50 devices on the bus. 6. This is the part-to-part skew between any two units tested with identical test conditions (Temperature, VCC, etc.). 4 ISL4486, ISL81486 Test Circuits and Waveforms VCC R DE Z DI Z DI VOD D 375 DE VCC VOD D Y VCM RD = 60 -7V to +12V Y VOC R 375 FIGURE 1A. VOD AND VOC FIGURE 1B. VOD WITH COMMON MODE LOAD FIGURE 1. DC DRIVER TEST CIRCUITS 3V DI 1.5V 1.5V 0V tPLH VCC CL = 100pF DE tPHL VOH 50% OUT (Y) 50% VOL Z DI RDIFF D tPHL Y tPLH CL = 100pF VOH OUT (Z) SIGNAL GENERATOR 50% 50% VOL 90% DIFF OUT (Y - Z) +VOD 90% 10% 10% tR -VOD tF SKEW = |CROSSING PT. OF Y & Z - CROSSING PT. OF Y & Z| FIGURE 2A. TEST CIRCUIT FIGURE 2B. MEASUREMENT POINTS FIGURE 2. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES DE DI SIGNAL GENERATOR 3V Z 110 VCC D SW Y DE 1.5V 1.5V 0V GND CL tZH OUTPUT HIGH PARAMETER OUTPUT RE DI SW CL (pF) tHZ Y/Z X 1/0 GND 50 tLZ Y/Z X 0/1 VCC 50 tZH Y/Z X 1/0 GND 50 tZL Y/Z X 0/1 VCC 50 FIGURE 3A. TEST CIRCUIT VOH - 0.5V OUT (Y, Z) VOH 2.3V 0V tZL tLZ VCC OUT (Y, Z) 2.3V OUTPUT LOW VOL + 0.5V V OL FIGURE 3B. MEASUREMENT POINTS FIGURE 3. DRIVER ENABLE AND DISABLE TIMES 5 tHZ ISL4486, ISL81486 Test Circuits and Waveforms (Continued) VCC CL = 100pF DE 3V Z DI DI RDIFF D Y 0V CL = 100pF SIGNAL GENERATOR +VOD DIFF OUT (Y - Z) -VOD FIGURE 4A. TEST CIRCUIT 0V FIGURE 4B. MEASUREMENT POINTS FIGURE 4. DRIVER DATA RATE RE 3V B +1.5V R A 15pF RO A 1.5V 1.5V 0V tPLH tPHL VCC SIGNAL GENERATOR 50% RO 50% 0V FIGURE 5A. TEST CIRCUIT FIGURE 5B. MEASUREMENT POINTS FIGURE 5. RECEIVER PROPAGATION DELAY 3V RE B SIGNAL GENERATOR 1k RO R VCC SW A RE 1.5V 1.5V 0V GND tZH 15pF OUTPUT HIGH tHZ VOH - 0.5V RO VOH 1.5V 0V PARAMETER DE A SW tHZ 0 +1.5V GND tLZ 0 -1.5V VCC tZH 0 +1.5V GND tZL 0 -1.5V VCC FIGURE 6A. TEST CIRCUIT tZL VCC RO 1.5V OUTPUT LOW VOL + 0.5V V OL FIGURE 6B. MEASUREMENT POINTS FIGURE 6. RECEIVER ENABLE AND DISABLE TIMES 6 tLZ ISL4486, ISL81486 Application Information Data Rate, Cables, and Terminations RS-485 and RS-422 are differential (balanced) data transmission standards for use in long haul or noisy environments. RS-422 is a subset of RS-485, so RS-485 transceivers are also RS-422 compliant. RS-422 is a pointto-multipoint (multidrop) standard, which allows only one driver and up to 10 (assuming one unit load devices) receivers on each bus. RS-485 is a true multipoint standard, which allows up to 32 one unit load devices (any mix of drivers and receivers) on each bus. To allow for multipoint operation, the RS-485 spec requires that drivers must handle bus contention without sustaining any damage. Twisted pair is the cable of choice for RS-485, RS-422, and PROFIBUS networks. Twisted pair cables tend to pick up noise and other electromagnetically induced voltages as common mode signals, which are effectively rejected by the differential receivers in these ICs. Another important advantage of RS-485 is the extended common mode range (CMR), which specifies that the driver outputs and receiver inputs withstand signals that range from +12V to -7V. RS-422 and RS-485 are intended for runs as long as 4000’ (~1200m), so the wide CMR is necessary to handle ground potential differences, as well as voltages induced in the cable by external fields. Receiver Features These devices utilize a differential input receiver for maximum noise immunity and common mode rejection. Input sensitivity is 200mV, as required by the RS422 and RS-485 specifications. Receiver inputs function with common mode voltages as great as 7V outside the power supplies (i.e., +12V and -7V), making them ideal for long networks, or industrial environments, where induced voltages are a realistic concern. Receiver input resistance surpasses the RS-422 spec of 4k, and exceeds the RS-485 “Unit Load” requirement of 12k minimum. The 20k input resistance allows at least 50 devices on the RS-485 bus. All the receivers include a “failsafe if open” function that guarantees a high level receiver output if the receiver inputs are unconnected (floating). Receivers easily meet the data rate supported by the driver, and receiver outputs are three-statable via the active low RE input. Driver Features The RS-485/RS-422 driver is a differential output device that delivers at least 2.3V across a 54 load (RS-485/ PROFIBUS), and at least 2.5V across a 100 load (RS-422) even with VCC = 4.5V. The drivers feature low propagation delay skew to maximize bit width, and to minimize EMI. Outputs of the drivers are not slew rate limited, so faster output transition times allow data rates of at least 40Mbps with the ISL4486, and 30Mbps with the ISL81486. Driver outputs are three-statable via the active high DE input. For parallel applications, bit-to-bit skews between any two ISL4486 transmitter and receiver pairs are guaranteed to be no worse than 15ns (6ns max for any two Tx, 9ns max for any two Rx). 7 RS-485/RS-422 are intended for network lengths up to 4000’ (~1200m), but the maximum system data rate decreases as the transmission length increases. According to guidelines in the RS-422 and PROFIBUS specifications, networks operating at data rates in excess of 3Mbps should be limited to cable lengths of 100m (328 feet) or less, and the PROFIBUS specification recommends that the more expensive “Type A” (22AWG) cable be used. Nevertheless, the ISL4486’s large differential output swing, fast transition times, and high drive-current output stages allow operation at 40Mbps over standard “CAT5” cables in excess of 400 feet (121m). Figure 8 details the ISL4486 performance at this condition, with a 120 termination resistor at both the driver and the receiver ends. Note that the differential signal delivered to the receiver at the end of the cable (A-B) still exceeds 1V, so even longer cables could be driven if lower noise margins are acceptable. If more noise margin is desired, shorter cables produce a larger receiver input signal as illustrated in Figure 7. Performance should be even better if the “Type A” cable is utilized. The lower data rate of the ISL81486 allows for driving longer cables. To minimize reflections, proper termination is imperative when using these high data rate transceivers. In point-to-point, or point-to-multipoint (single driver on bus) networks, the main cable should be terminated in its characteristic impedance (typically 120 for “CAT5”, and 220 for “Type A”) at the end farthest from the driver. In multi-receiver applications, stubs connecting receivers to the main cable should be kept as short as possible. Multipoint (multi-driver) systems require that the main cable be terminated in its characteristic impedance at both ends. Stubs connecting a transceiver to the main cable should be kept as short as possible. Built-In Driver Overload Protection As stated previously, the RS-485 spec requires that drivers survive worst case bus contentions undamaged. These transmitters meet this requirement via driver output short circuit current limits, and on-chip thermal shutdown circuitry. The driver output stages incorporate short circuit current limiting circuitry which ensures that the output current never exceeds the RS-485 spec, even at the common mode voltage range extremes. In the event of a major short circuit condition, the devices also include a thermal shutdown feature that disables the drivers whenever the die temperature becomes excessive. This eliminates the power dissipation, allowing the die to cool. The drivers automatically reenable after the die temperature drops about 15 degrees. If the contention persists, the thermal shutdown/reenable cycle repeats until the fault is cleared. Receivers stay operational during thermal shutdown. ISL4486, ISL81486 0 5 RO 0 DRIVER+CABLE DELAY 3 1.5 (~290ns) A-B 0 -1.5 -3 DI = 40Mbps 0 5 RO 0 DRIVER+CABLE DELAY 3 1.5 A-B -1.5 -3 TIME (10ns/DIV) FIGURE 7. ISL4486 DRIVER AND RECEIVER WAVEFORMS DRIVING 200 FEET (61 METERS) OF CAT5 CABLE (DOUBLE TERMINATED WITH 120) FIGURE 8. ISL4486 DRIVER AND RECEIVER WAVEFORMS DRIVING 400 FEET (121 METERS) OF CAT5 CABLE (DOUBLE TERMINATED WITH 120) 950 DRIVER OUTPUT (V) 5 RDIFF = 54, CL = 100pF 3 A/Y 900 B/Z 850 DE = VCC, RE = X 2 ICC (A) 1 0 DIFF WAVEFORM (V) (~585ns) 0 TIME (10ns/DIV) 4 5 DRIVER INPUT (V) 5 RECEIVER OUTPUT (V) DI = 40Mbps DRIVER INPUT (V) VCC = 5V, TA = 25°C, ISL4486 and ISL81486; Unless Otherwise Specified RECEIVER INPUT (V) RECEIVER INPUT (V) RECEIVER OUTPUT (V) Typical Performance Curves 800 3 1.5 DE = GND, RE = X 750 A/Y - B/Z 0 -1.5 700 -40 -3 -25 TIME (10ns/DIV) FIGURE 9. ISL81486 DRIVER WAVEFORMS AT 30Mbps PER FIGURE 4 50 85 75 4 DIFFERENTIAL OUTPUT VOLTAGE (V) DRIVER OUTPUT CURRENT (mA) 25 FIGURE 10. SUPPLY CURRENT vs TEMPERATURE 120 100 80 60 40 20 0 0 TEMPERATURE (°C) 0 1 2 3 4 DIFFERENTIAL OUTPUT VOLTAGE (V) FIGURE 11. DRIVER OUTPUT CURRENT vs DIFFERENTIAL OUTPUT VOLTAGE 8 5 3.8 RDIFF = 100 3.6 3.4 3.2 RDIFF = 54 3 2.8 -40 -25 0 25 50 75 85 TEMPERATURE (°C) FIGURE 12. DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs TEMPERATURE ISL4486, ISL81486 Typical Performance Curves VCC = 5V, TA = 25°C, ISL4486 and ISL81486; Unless Otherwise Specified (Continued) 3 12 RDIFF = 54 2.5 11 |tPHL(Y or Z) - tPLH(Y or Z)| = PW Distortion tPLHZ 2 tPLHY 10 SKEW (ns) PROPAGATION DELAY (ns) RDIFF = 54 9 tPHLY 1.5 |tPHLY - tPLHZ| or |tPLHY - tPHLZ| 1 tPHLZ 8 0.5 |CROSSING PT. OF Y & Z CROSSING PT. OF Y & Z| 0 -25 50 25 0 -40 85 75 -25 TEMPERATURE (°C) 0 RO DRIVER OUTPUT (V) 5 4 A/Y 3 2 B/Z 1 RECEIVER OUTPUT (V) 5 DRIVER INPUT (V) RECEIVER OUTPUT (V) DRIVER OUTPUT (V) RDIFF = 54, CL = 15pF DI 0 0 5 0 RO 5 4 3 OUTPUT CURRENT (mA) -160 B/Z 2 1 A/Y 0 FIGURE 16. DRIVER AND RECEIVER WAVEFORMS, HIGH TO LOW Die Characteristics Y OR Z = LOW SUBSTRATE POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: 528 PROCESS: Y OR OR ZZ == HIGH HIGH Y -7 -6 -4 -2 0 2 4 6 OUTPUT VOLTAGE (V) 8 Si Gate BiCMOS 10 12 FIGURE 17. DRIVER OUTPUT CURRENT vs SHORT CIRCUIT VOLTAGE 9 5 0 TIME (10ns/DIV) FIGURE 15. DRIVER AND RECEIVER WAVEFORMS, LOW TO HIGH -60 -80 -100 -120 -140 85 75 RDIFF = 54, CL = 15pF DI TIME (10ns/DIV) 160 140 120 100 80 60 40 20 0 -20 -40 50 FIGURE 14. DRIVER SKEW AND PULSE DISTORTION vs TEMPERATURE FIGURE 13. DRIVER PROPAGATION DELAY vs TEMPERATURE 5 0 25 TEMPERATURE (°C) DRIVER INPUT (V) 7 -40 ISL4486, ISL81486 Mini Small Outline Plastic Packages (MSOP) N M8.118 (JEDEC MO-187AA) 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE E1 INCHES E -B- INDEX AREA 1 2 0.20 (0.008) A B C TOP VIEW 4X 0.25 (0.010) R1 R GAUGE PLANE SEATING PLANE -CA 4X A2 A1 b -H- 0.10 (0.004) L1 SEATING PLANE C D 0.20 (0.008) C a CL E1 0.20 (0.008) C D -B- END VIEW NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-187BA. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 3. Dimension “D” does not include mold flash, protrusions or gate burrs and are measured at Datum Plane. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions and are measured at Datum Plane. - H - Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. Formed leads shall be planar with respect to one another within 0.10mm (0.004) at seating Plane. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Datums -A -H- . and - B - to be determined at Datum plane 11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. 10 MAX MIN MAX NOTES 0.037 0.043 0.94 1.10 - A1 0.002 0.006 0.05 0.15 - A2 0.030 0.037 0.75 0.95 - b 0.010 0.014 0.25 0.36 9 c 0.004 0.008 0.09 0.20 - D 0.116 0.120 2.95 3.05 3 E1 0.116 0.120 2.95 3.05 4 0.026 BSC 0.65 BSC - E 0.187 0.199 4.75 5.05 - L 0.016 0.028 0.40 0.70 6 0.037 REF N C SIDE VIEW MIN A L1 -A- e SYMBOL e L MILLIMETERS 0.95 REF 8 R 0.003 R1 0 - 8 - 0.07 0.003 - 5o 15o 0o 6o 7 - - 0.07 - - 5o 15o - 0o 6o Rev. 2 01/03 ISL4486, ISL81486 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N INDEX AREA 0.25(0.010) M H 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- 1 2 SYMBOL 3 L SEATING PLANE -A- h x 45o A D -C- µ e A1 B 0.25(0.010) M C C A M B S 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. MILLIMETERS MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 8o 0o N NOTES: MAX A1 e 0.10(0.004) MIN 8 0o 8 7 8o Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11