SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Enhanced Single Port Series - MS-012 Description The series provides single port protection using a fixed voltage switching device for negative surges. Positive surges are routed though enhanced switching diodes to a ground reference. The series is also pin-to-pin compatible to industry standard programmable SO-8 SLIC protectors. Features & Benefits Agency Approvals Agency diodes for positive voltage surges Agency File Number E133083 surged in excess of ratings one package Pinout footprint (Tip) 1 8 (Tip) (NC) 2 7 (Ground) (NC) 3 6 (Ground) (Ring) 4 5 (Ring) Applicable Global Standards Level Schematic Symbol 1 8 2 7 3 6 4 5 Electrical Characteristics Part Number Marking P0641DF-1E P0721DF-1E P0901DF-1E P0991DF-1E P1001DF-1E P1101DF-1E P1301DF-1E P1701DF-1E P0641F1E P0721F1E P0901F1E P0991F1E P1001F1E P1101F1E P1301F1E P1701F1E VDRM@ IDRM=5μA VS@100V/μs IH IS IT@VT VT@IT=1 Amps VF@25° V min V max mA min mA max A max V max V max 58 65 75 80 85 95 120 160 77 88 98 104 110 130 160 200 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 1 1 1 1 1 1 1 1 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - VF < 8.5 volts @ 10 x 700μs Amps © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 105 Capacitance See Capacitance Values Table Fixed Voltage Enh. Single The MS-012 packaged Fixed Voltage Enhanced Single Port Series are SIDACtor® devices designed to protect sensitive SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1,8-6,7 / 4,5-6,7 Tip-Ground, Ring-Ground MIN MAX 40 90 35 85 30 80 25 75 25 75 25 70 20 70 20 70 P0641DF-1E P0721DF-1E P0901DF-1E P0991DF-1E P1001DF-1E P1101DF-1E P1301DF-1E P1701DF-1E pF Pin 1,8-4,5 Tip-Ring MIN MAX 20 45 20 45 20 40 15 35 15 35 15 30 15 30 15 30 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings ITSM IPP Series F di/dt 2x10μs 1.2x50μs/8x20μs 10x700/5x310μs 10x1000μs 600VRMS 1s A min A min A min A min A min Amps/μs max 120 100 50 30 1 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC 5IFEFWJDFNVTUJOJUJBMMZCFJOUIFSNBMFRVJMJCSJVNXJUI¡$< TJ < +150°C Thermal Considerations Package MS-012 1 2 3 8 7 6 Symbol Parameter Value Unit TJ 0QFSBUJOH+VODUJPO5FNQFSBUVSF3BOHF -40 to +150 °C TS 4UPSBHF5FNQFSBUVSF3BOHF -65 to +150 °C 30JA 5IFSNBM3FTJTUBODF+VODUJPOUP"NCJFOU 120 °CW 5 4 V-I Characteristics tr x td Pulse Waveform +I IPP – Peak Pulse Current – %IPP Fixed Voltage Enh. Single Part Number VF VS VDRM VT -V IDRM +V IH IS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 tr td t – Time (μs) -I 106 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors SLIC Protection Normalized DC Holding Current vs. Case Temperature IH 8 6 25 °C 4 2 0 -4 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 -6 0.4 -8 -40 -40 -20 0 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) ¡$TFD.BY TS(max) to TL - Ramp-up Rate ¡$TFD.BY Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate ¡$TFD.BY Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 3BUFE7%3. (VDC ¡$PS¡$PS IST.*-45%.FUIPE +&%&$ JESD22-A-101 Physical Specifications Temp Cycling ¡$UP¡$NJOEXFMMVQUP DZDMFT.*-45%.FUIPE &*"+&%&$ JESD22-A104 Lead Material Copper Alloy Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" +&%&$+&4%" Terminal Finish 100% Matte-Tin Plated High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) +&%&$+&4%" Low Temp Storage ¡$IST Body Material 6-SFDPHOJ[FEFQPYZNFFUJOHnBNNBCJMJUZ classification 94V-0 Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS DZDMFT.*-45%.FUIPE +&%&$ JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" +&%&$+&4%" Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 107 Fixed Voltage Enh. Single 10 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-012 Inches Dimension A A1 A2 # C D E E1 e L o Recommended Soldering Pad Outline (Reference Only) Fixed Voltage Enh. Single MIN Millimeters MAX 0.053 0.069 0.004 0.010 0.043 0.065 0.012 0.020 0.007 0.010 0.189 0.197 0.228 0.244 0.150 0.157 #4$ 0.016 0.050 MIN MAX 1.35 1.75 0.10 0.25 1.25 1.65 0.31 0.51 0.17 0.25 4.80 5.00 5.80 6.20 3.80 4.00 #4$ 0.40 1.27 #4$Basic Spacing between Centers Part Numbering Part Marking P xxx 1 DF -1E SINGLE ENHANCED TYPE P: SIDACtor IPP RATING MEDIAN VOLTAGE XXXXXF1E o XXXXX PACKAGE TYPE CONSTRUCTION VARIABLE Part Number Code (Refer to Electrical Characteristics Table) Date Code Packing Options Package Type Description Quantity Added Suffix Industry Standard D MS-012 SMT 8-pin 40*$5BQFBOE3FFM Pack 2500 /" EIA-481-D Tape and Reel Specifications — MS-012 1.55 (.061) 4.0 (.158) DIMENSIONS ARE: 2.0 (.079) 8.0 (.315) 0.8 MIN. (0.03) 5.5 (.216) o 6.4 (.252) 1.50 ø MIN. (.059) Carrier Tape Embossment 0.512 (13.0) Arbor Hole Dia. MILLIMETERS (INCHES) 0.40 (0.016) 12.0 (.472) Cover 0 MIN. Tape Direction of Feed 2.1 (.083) 12.99 (330.0) Dimensions are in inches (and millimeters). Direction of Feed 0.49 (12.4) 108 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.