IRF840, SiHF840 www.vishay.com Vishay Siliconix Power MOSFET FEATURES PRODUCT SUMMARY VDS (V) • Dynamic dV/dt rating 500 RDS(on) () VGS = 10 V Qg max. (nC) 63 • Fast switching Qgs (nC) 9.3 • Ease of paralleling Qgd (nC) 32 • Simple drive requirements Configuration Available • Repetitive avalanche rated 0.85 Single Available • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 D Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non-RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details. TO-220AB G DESCRIPTION G D S Third generation power MOSFETs from Vishay provide the designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness. The TO-220AB package is universally preferred for all commercial-industrial applications at power dissipation levels to approximately 50 W. The low thermal resistance and low package cost of the TO-220AB contribute to its wide acceptance throughout the industry. S N-Channel MOSFET ORDERING INFORMATION Package TO-220AB IRF840PbF Lead (Pb)-free SiHF840-E3 IRF840 SnPb SiHF840 ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted) PARAMETER SYMBOL LIMIT UNIT Drain-Source Voltage VDS 500 V Gate-Source Voltage VGS ± 20 V VGS at 10 V Continuous Drain Current Pulsed Drain TC = 25 °C TC = 100 °C Current a ID IDM Linear Derating Factor 8.0 5.1 A 32 1.0 W/°C mJ Single Pulse Avalanche Energy b EAS 510 Repetitive Avalanche Current a IAR 8.0 A Repetitive Avalanche Energy a EAR 13 mJ Maximum Power Dissipation TC = 25 °C Peak Diode Recovery dV/dt c Operating Junction and Storage Temperature Range Soldering Recommendations (Peak temperature) Mounting Torque d for 10 s 6-32 or M3 screw PD 125 W dV/dt 3.5 V/ns TJ, Tstg -55 to +150 300 °C 10 lbf · in 1.1 N·m Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. VDD = 50 V, starting TJ = 25 °C, L = 14 mH, Rg = 25 , IAS = 8.0 A (see fig. 12). c. ISD 8.0 A, dI/dt 100 A/μs, VDD VDS, TJ 150 °C. d. 1.6 mm from case. S16-0754-Rev. D, 02-May-16 Document Number: 91070 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IRF840, SiHF840 www.vishay.com Vishay Siliconix THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYP. MAX. Maximum Junction-to-Ambient RthJA - 62 Case-to-Sink, Flat, Greased Surface RthCS 0.50 - Maximum Junction-to-Case (Drain) RthJC - 1.0 UNIT °C/W SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Static Drain-Source Breakdown Voltage VDS Temperature Coefficient Gate-Source Threshold Voltage VDS VGS = 0 V, ID = 250 μA 500 - - V VDS/TJ Reference to 25 °C, ID = 1 mA - 0.78 - V/°C VGS(th) VDS = VGS, ID = 250 μA 2.0 - 4.0 V Gate-Source Leakage IGSS VGS = ± 20 V - - ± 100 nA Zero Gate Voltage Drain Current IDSS VDS = 500 V, VGS = 0 V - - 25 VDS = 400 V, VGS = 0 V, TJ = 125 °C - - 250 μA - - 0.85 gfs VDS = 50 V, ID = 4.8 A b 4.9 - - S Input Capacitance Ciss 1300 - Coss - 310 - Reverse Transfer Capacitance Crss VGS = 0 V, VDS = 25 V, f = 1.0 MHz, see fig. 5 - Output Capacitance - 120 - - - 63 - - 9.3 Drain-Source On-State Resistance Forward Transconductance RDS(on) ID = 4.8 A b VGS = 10 V Dynamic Total Gate Charge Qg Gate-Source Charge Qgs Gate-Drain Charge Qgd - - 32 Turn-On Delay Time td(on) - 14 - tr - 23 - - 49 - - 20 - - 4.5 - - 7.5 - 0.6 - 2.8 - - 8.0 - - 32 Rise Time Turn-Off Delay Time td(off) Fall Time tf Internal Drain Inductance LD Internal Source Inductance LS Gate Input Resistance Rg VGS = 10 V ID = 8 A, VDS = 400 V, see fig. 6 and 13 b VDD = 250 V, ID = 8 A Rg = 9.1 , RD = 31, see fig. 10 b Between lead, 6 mm (0.25") from package and center of die contact D pF nC ns nH G S f = 1 MHz, open drain Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulsed Diode Forward Current a ISM Body Diode Voltage VSD Body Diode Reverse Recovery Time trr Body Diode Reverse Recovery Charge Qrr Forward Turn-On Time ton MOSFET symbol showing the integral reverse p - n junction diode D A G S TJ = 25 °C, IS = 8 A, VGS = 0 V b TJ = 25 °C, IF = 8 A, dI/dt = 100 A/μs b - - 2.0 V - 460 970 ns - 4.2 8.9 μC Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD) Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. Pulse width 300 μs; duty cycle 2 %. S16-0754-Rev. D, 02-May-16 Document Number: 91070 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IRF840, SiHF840 www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) ID, Drain Current (A) 15 V 10 V 8.0 V 7.0 V 6.0 V 5.5 V 5.0 V Bottom 4.5 V 101 4.5 V 100 20 µs Pulse Width TC = 25 °C 100 101 VDS, Drain-to-Source Voltage (V) 91070_01 3.0 RDS(on), Drain-to-Source On Resistance (Normalized) VGS Top 2.5 ID = 8.0 A VGS = 10 V 2.0 1.5 1.0 0.5 0.0 - 60 - 40 - 20 0 TJ, Junction Temperature (°C) 91070_04 Fig. 1 - Typical Output Characteristics, TC = 25 °C Fig. 4 - Normalized On-Resistance vs. Temperature 2500 VGS 15 V 10 V 8.0 V 7.0 V 6.0 V 5.5 V 5.0 V Bottom 4.5 V VGS = 0 V, f = 1 MHz Ciss = Cgs + Cgd, Cds Shorted Crss = Cgd Coss = Cds + Cgd Top 2000 4.5 V Capacitance (pF) ID, Drain Current (A) 101 Ciss 1500 1000 Coss 500 100 Crss 20 µs Pulse Width TC = 150 °C 100 0 100 101 VDS, Drain-to-Source Voltage (V) 91070_02 Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage 101 25 °C 100 20 µs Pulse Width VDS = 50 V 4 5 6 7 8 9 VGS, Gate-to-Source Voltage (V) Fig. 3 - Typical Transfer Characteristics S16-0754-Rev. D, 02-May-16 VGS, Gate-to-Source Voltage (V) ID, Drain Current (A) 20 150 °C 101 VDS, Drain-to-Source Voltage (V) 91070_05 Fig. 2 - Typical Output Characteristics, TC = 150 °C 91070_03 20 40 60 80 100 120 140 160 ID = 8.0 A VDS = 400 V 16 VDS = 250 V VDS = 100 V 12 8 4 For test circuit see figure 13 0 10 0 91070_06 15 30 45 60 75 QG, Total Gate Charge (nC) Fig. 6 - Typical Gate Charge vs. Drain-to-Source Voltage Document Number: 91070 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IRF840, SiHF840 www.vishay.com Vishay Siliconix 150 °C ID, Drain Current (A) ISD, Reverse Drain Current (A) 8.0 101 25 °C 4.0 2.0 VGS = 0 V 100 0.0 0.4 0.6 0.8 1.0 1.4 1.2 25 VSD, Source-to-Drain Voltage (V) 91070_07 50 75 100 125 150 TC, Case Temperature (°C) 91070_09 Fig. 7 - Typical Source-Drain Diode Forward Voltage Fig. 9 - Maximum Drain Current vs. Case Temperature RD 102 VDS Operation in this area limited by RDS(on) 5 ID, Drain Current (A) 6.0 VGS 10 µs 2 D.U.T. RG + - VDD 10 100 µs 5 10 V Pulse width ≤ 1 µs Duty factor ≤ 0.1 % 1 ms 2 1 10 ms Fig. 10a - Switching Time Test Circuit 5 TC = 25 °C TJ = 150 °C Single Pulse 2 0.1 0.1 2 5 1 2 5 10 2 5 102 VDS 2 5 103 2 5 90 % 104 VDS, Drain-to-Source Voltage (V) 91070_08 Fig. 8 - Maximum Safe Operating Area 10 % VGS td(on) td(off) tf tr Fig. 10b - Switching Time Waveforms Thermal Response (ZthJC) 10 1 0 - 0.5 0.2 0.1 0.1 0.05 0.02 0.01 PDM Single Pulse (Thermal Response) t1 t2 Notes: 1. Duty Factor, D = t1/t2 2. Peak Tj = PDM x ZthJC + TC 10-2 10-3 10-5 10-4 10-3 10-2 0.1 1 10 102 Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case S16-0754-Rev. D, 02-May-16 Document Number: 91070 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IRF840, SiHF840 www.vishay.com Vishay Siliconix L Vary tp to obtain required IAS VDS VDS tp VDD D.U.T. RG + - IAS V DD VDS 10 V 0.01 Ω tp IAS Fig. 12a - Unclamped Inductive Test Circuit Fig. 12b - Unclamped Inductive Waveforms EAS, Single Pulse Energy (mJ) 1200 ID 3.6 A 5.1 A Bottom 8.0 A Top 1000 800 600 400 200 0 VDD = 50 V 25 91070_12c 50 75 100 125 150 Starting TJ, Junction Temperature (°C) Fig. 12c - Maximum Avalanche Energy vs. Drain Current Current regulator Same type as D.U.T. 50 kΩ QG 10 V 12 V 0.2 µF 0.3 µF QGS + QGD VG D.U.T. - VDS VGS 3 mA Charge Fig. 13a - Basic Gate Charge Waveform S16-0754-Rev. D, 02-May-16 IG ID Current sampling resistors Fig. 13b - Gate Charge Test Circuit Document Number: 91070 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IRF840, SiHF840 www.vishay.com Vishay Siliconix Peak Diode Recovery dV/dt Test Circuit + D.U.T. Circuit layout considerations • Low stray inductance • Ground plane • Low leakage inductance current transformer + - - Rg • • • • + V - DD dV/dt controlled by Rg Driver same type as D.U.T. ISD controlled by duty factor “D” D.U.T. - device under test Driver gate drive Period P.W. + D= P.W. Period V GS = 10 V a D.U.T. ISD waveform Reverse recovery current D.U.T. VDS Body diode forward current dI/dt waveform Diode recovery dV/dt Re-applied voltage V DD Body diode forward drop Inductor current Ripple ≤ 5 % ISD Note a. VGS = 5 V for logic level devices Fig. 14 - For N-Channel Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?91070. S16-0754-Rev. D, 02-May-16 Document Number: 91070 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com Vishay Siliconix TO-220-1 A E DIM. Q H(1) D 3 2 L(1) 1 M* L b(1) INCHES MIN. MAX. MIN. MAX. A 4.24 4.65 0.167 0.183 b 0.69 1.02 0.027 0.040 b(1) 1.14 1.78 0.045 0.070 F ØP MILLIMETERS c 0.36 0.61 0.014 0.024 D 14.33 15.85 0.564 0.624 E 9.96 10.52 0.392 0.414 e 2.41 2.67 0.095 0.105 e(1) 4.88 5.28 0.192 0.208 F 1.14 1.40 0.045 0.055 H(1) 6.10 6.71 0.240 0.264 0.115 J(1) 2.41 2.92 0.095 L 13.36 14.40 0.526 0.567 L(1) 3.33 4.04 0.131 0.159 ØP 3.53 3.94 0.139 0.155 Q 2.54 3.00 0.100 0.118 ECN: X15-0364-Rev. C, 14-Dec-15 DWG: 6031 Note • M* = 0.052 inches to 0.064 inches (dimension including protrusion), heatsink hole for HVM C b e J(1) e(1) Package Picture ASE Revison: 14-Dec-15 Xi’an Document Number: 66542 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000