SiA462DJ Datasheet

New Product
SiA462DJ
Vishay Siliconix
N-Channel 30 V (D-S) MOSFET
FEATURES
PRODUCT SUMMARY
VDS (V)
30
RDS(on) () (Max.)
ID (A)a
0.018 at VGS = 10 V
12
0.020 at VGS = 6 V
12
0.022 at VGS = 4.5 V
12
Qg (Typ.)
5 nC
• TrenchFET® Power MOSFET
• 100 % Rg Tested
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
PowerPAK SC-70-6L-Single
• DC/DC Converters and Synchronous Buck Converters
- Lower Ringing Voltage from Soft Turn-On
- High Efficiency from Fast Turn-Off
- Lower Shoot-Through Possibility
1
D
2
D
D
3
6
G
D
Marking Code
5
S
D
2.05 mm
S
ASX
2.05 mm
Part # code
4
G
XXX
Lot Traceability
and Date code
Bottom View
Ordering Information:
SiA462DJ-T1-GE3 (Lead (Pb)-free and Halogen-free)
S
N-Channel MOSFET
ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted)
Parameter
Drain-Source Voltage
Symbol
VDS
Limit
30
Gate-Source Voltage
VGS
± 20
Continuous Drain Current (TJ = 150 °C)
TA = 25 °C
12a
ID
12a,b, c
9.7b, c
40
TA = 70 °C
IDM
Pulsed Drain Current (t = 300 µs)
Continuous Source-Drain Diode Current
TC = 25 °C
TA = 25 °C
TC = 70 °C
TA = 25 °C
2.9b, c
19
TJ, Tstg
Operating Junction and Storage Temperature Range
12
PD
TA = 70 °C
A
12a
IS
TC = 25 °C
Maximum Power Dissipation
V
12a
TC = 25 °C
TC = 70 °C
Unit
W
3.5b, c
2.2b, c
- 55 to 150
Soldering Recommendations (Peak Temperature)d, e
260
°C
THERMAL RESISTANCE RATINGS
Parameter
Junction-to-Ambientb, f
t5s
Steady State
Symbol
RthJA
Typical
28
5.3
Maximum
36
6.5
Unit
Maximum
°C/W
RthJC
Maximum Junction-to-Case (Drain)
Notes:
a. Based on package limited.
b. Surface mounted on 1" x 1" FR4 board.
c. t = 5 s.
d. See solder profile (www.vishay.com/doc?73257). The PowerPAK SC-70 is a leadless package. The end of the lead terminal is exposed copper
(not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed and is not
required to ensure adequate bottom side solder interconnection.
e. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components.
f. Maximum under steady state conditions is 80 °C/W.
Document Number: 63269
S13-0628-Rev. A, 25-Mar-13
For technical questions, contact:: [email protected]
www.vishay.com
1
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SiA462DJ
Vishay Siliconix
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted
Parameter
Symbol
Test Conditions
Min.
VDS
VGS = 0 V, ID = 250 µA
30
Typ.
Max.
Unit
Static
Drain-Source Breakdown Voltage
VDS/TJ
VDS Temperature Coefficient
VGS(th) Temperature Coefficient
VGS(th)/TJ
Gate-Source Threshold Voltage
V
34
ID = 250 µA
mV/°C
-5
VGS(th)
VDS = VGS, ID = 250 µA
2.4
V
Gate-Source Leakage
IGSS
VDS = 0 V, VGS = ± 20 V
± 100
nA
Zero Gate Voltage Drain Current
IDSS
VDS = 30 V, VGS = 0 V
1
VDS = 30 V, VGS = 0 V, TJ = 55 °C
10
On-State Drain Currenta
ID(on)
Drain-Source On-State Resistancea
RDS(on)
Forward Transconductancea
gfs
VDS 5 V, VGS = 10 V
1.2
10
µA
A
VGS = 10 V, ID = 9 A
0.015
0.018
VGS = 6 V, ID = 7 A
0.016
0.020
VGS = 4.5 V, ID = 7 A
0.018
0.022
VDS = 10 V, ID = 9 A
35

S
Dynamicb
Input Capacitance
Ciss
Output Capacitance
Coss
Reverse Transfer Capacitance
Crss
Total Gate Charge
Qg
Gate-Source Charge
Qgs
Gate-Drain Charge
Qgd
Gate Resistance
Rg
570
VDS = 15 V, VGS = 0 V, f = 1 MHz
52
VDS = 15 V, VGS = 10 V, ID = 12 A
VDS = 15 V, VGS = 4.5 V, ID = 12 A
tr
Rise Time
td(off)
Turn-Off Delay Time
Fall Time
Turn-On Delay Time
VDD = 15 V, RL = 1.5 
ID  10 A, VGEN = 10 V, Rg = 1 
1.7
0.2
1
2
5
10
10
20
15
30
10
20
12
25
15
30
VDD = 15 V, RL = 1.5 
ID  10 A, VGEN = 4.5 V, Rg = 1 
tf
Fall Time
7.5
td(on)
td(off)
Turn-Off Delay Time
17
5
tf
tr
Rise Time
11
nC
1.6
f = 1 MHz
td(on)
Turn-On Delay Time
pF
126
15
30
10
20

ns
Drain-Source Body Diode Characteristics
Continuous Source-Drain Diode Current
a
IS
Pulse Diode Forward Current
ISM
Body Diode Voltage
VSD
TC = 25 °C
12
40
IS = 10 A
A
0.85
1.2
Body Diode Reverse Recovery Time
trr
20
40
ns
Body Diode Reverse Recovery Charge
Qrr
11
20
nC
Reverse Recovery Fall Time
ta
Reverse Recovery Rise Time
tb
IF = 10 A, dI/dt = 100 A/µs, TJ = 25 °C
12
8
V
ns
Notes:
a. Pulse test; pulse width  300 µs, duty cycle  2 %.
b. Guaranteed by design, not subject to production testing.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
www.vishay.com
2
For technical questions, contact:: [email protected]
Document Number: 63269
S13-0628-Rev. A, 25-Mar-13
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SiA462DJ
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
40
10
VGS = 10 V thru 4 V
8
ID - Drain Current (A)
ID - Drain Current (A)
32
24
16
VGS = 3 V
8
6
4
TC = 25 °C
TC = 125 °C
2
0
TC = - 55 °C
0
0.0
0.5
1.0
1.5
2.0
0.0
0.5
VDS - Drain-to-Source Voltage (V)
Output Characteristics
1.0
1.5
2.0
2.5
VGS - Gate-to-Source Voltage (V)
3.0
Transfer Characteristics
0.025
800
700
Ciss
600
C - Capacitance (pF)
RDS(on) - On-Resistance (Ω)
0.022
VGS = 4.5 V
0.019
VGS = 6 V
0.016
VGS = 10 V
500
400
300
Coss
200
0.013
Crss
100
0.010
0
0
8
16
24
32
0
40
5
ID - Drain Current (A)
On-Resistance vs. Drain Current and Gate Voltage
30
Capacitance
1.8
10
ID = 9 A
8
RDS(on) - On-Resistance (Normalized)
ID = 12 A
VGS - Gate-to-Source Voltage (V)
10
15
20
25
VDS - Drain-to-Source Voltage (V)
VDS = 15 V
6
VDS = 7.5 V
VDS = 24 V
4
2
1.6
VGS = 10 V, 6 V
1.4
VGS = 4.5 V
1.2
1.0
0.8
0.6
0
0
2
4
6
8
Qg - Total Gate Charge (nC)
Gate Charge
Document Number: 63269
S13-0628-Rev. A, 25-Mar-13
10
12
- 50
- 25
0
25
50
75
100
TJ - Junction Temperature (°C)
125
150
On-Resistance vs. Junction Temperature
For technical questions, contact:: [email protected]
www.vishay.com
3
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SiA462DJ
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
100
0.05
ID = 9 A
RDS(on) - On-Resistance (Ω)
IS - Source Current (A)
0.04
10
TJ = 150 °C
TJ = 25 °C
1
0.03
TJ = 125 °C
0.02
TJ = 25 °C
0.01
0.1
0.0
0.00
0.2
0.4
0.6
0.8
1.0
VSD - Source-to-Drain Voltage (V)
1.2
0
2.2
30
2.0
25
1.8
20
1.6
ID = 250 μA
10
1.2
5
0
0.001
1.0
- 25
0
25
50
75
100
125
10
15
1.4
50
4
6
8
VGS - Gate-to-Source Voltage (V)
On-Resistance vs. Gate-to-Source Voltage
Power (W)
VGS(th) (V)
Source-Drain Diode Forward Voltage
2
150
0.01
0.1
TJ - Temperature (°C)
Threshold Voltage
1
Time (s)
10
100
1000
Single Pulse Power, Junction-to-Ambient
100
Limited by RDS(on)*
ID - Drain Current (A)
10
100 μs
1 ms
1
10 ms
100 ms
1s
10 s
0.1
TA = 25 °C
DC
BVDSS Limited
0.01
0.1
1
10
100
VDS - Drain-to-Source Voltage (V)
* VGS > minimum VGS at which RDS(on) is specified
Safe Operating Area, Junction-to-Ambient
www.vishay.com
4
For technical questions, contact:: [email protected]
Document Number: 63269
S13-0628-Rev. A, 25-Mar-13
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SiA462DJ
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
30
ID - Drain Current (A)
25
20
15
10
Package Limited
5
0
0
25
50
75
100
125
150
TC - Case Temperature (°C)
Current Derating*
Power Dissipation (W)
20
15
10
5
0
25
50
75
100
125
TC - Case Temperature (°C)
150
Power, Junction-to-Case
* The power dissipation PD is based on TJ(max.) = 150 °C, using junction-to-case thermal resistance, and is more useful in settling the upper
dissipation limit for cases where additional heatsinking is used. It is used to determine the current rating, when this rating falls below the package
limit.
Document Number: 63269
S13-0628-Rev. A, 25-Mar-13
For technical questions, contact:: [email protected]
www.vishay.com
5
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SiA462DJ
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
1
Normalized Effective Transient
Thermal Impedance
Duty Cycle = 0.5
0.2
0.1
Notes:
0.05
PDM
0.1
t1
0.02
t2
1. Duty Cycle, D =
t1
t2
2. Per Unit Base = RthJA = 80 C/W
3. TJM - TA = PDMZthJA(t)
Single Pulse
4. Surface Mounted
0.01
10-4
10-3
10-2
10-1
1
Square Wave Pulse Duration (s)
10
100
1000
Normalized Thermal Transient Impedance, Junction-to-Ambient
1
Normalized Effective Transient
Thermal Impedance
Duty Cycle = 0.5
0.2
0.1
0.05
0.1
10-4
0.02
Single Pulse
10-3
10-2
10-1
Square Wave Pulse Duration (s)
Normalized Thermal Transient Impedance, Junction-to-Case
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?63269.
www.vishay.com
6
For technical questions, contact:: [email protected]
Document Number: 63269
S13-0628-Rev. A, 25-Mar-13
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Package Information
Vishay Siliconix
b
e
PIN1
PIN3
PIN1
PIN2
PIN3
PIN5
K1
E1
E1
K
PIN6
K3
D1
D1
K
D2
D1
E3
E1
E2
K4
K
L
PIN2
b
e
L
PowerPAK® SC70-6L
PIN6
PIN4
K2
PIN5
K1
K2
BACKSIDE VIEW OF SINGLE
PIN4
K2
BACKSIDE VIEW OF DUAL
A
D
C
A1
E
Notes:
1. All dimensions are in millimeters
2. Package outline exclusive of mold flash and metal burr
3. Package outline inclusive of plating
Z
z
DETAIL Z
SINGLE PAD
DIM
A
MILLIMETERS
DUAL PAD
INCHES
MILLIMETERS
INCHES
Min
Nom
Max
Min
Nom
Max
Min
Nom
Max
Min
Nom
Max
0.675
0.75
0.80
0.027
0.030
0.032
0.675
0.75
0.80
0.027
0.030
0.032
A1
0
-
0.05
0
-
0.002
0
-
0.05
0
-
0.002
b
0.23
0.30
0.38
0.009
0.012
0.015
0.23
0.30
0.38
0.009
0.012
0.015
C
0.15
0.20
0.25
0.006
0.008
0.010
0.15
0.20
0.25
0.006
0.008
0.010
D
1.98
2.05
2.15
0.078
0.081
0.085
1.98
2.05
2.15
0.078
0.081
0.085
D1
0.85
0.95
1.05
0.033
0.037
0.041
0.513
0.613
0.713
0.020
0.024
0.028
D2
0.135
0.235
0.335
0.005
0.009
0.013
E
1.98
2.05
2.15
0.078
0.081
0.085
1.98
2.05
2.15
0.078
0.081
0.085
E1
1.40
1.50
1.60
0.055
0.059
0.063
0.85
0.95
1.05
0.033
0.037
0.041
E2
0.345
0.395
0.445
0.014
0.016
0.018
E3
0.425
0.475
0.525
0.017
0.019
0.021
e
0.65 BSC
0.026 BSC
0.65 BSC
0.026 BSC
K
0.275 TYP
0.011 TYP
0.275 TYP
0.011 TYP
K1
0.400 TYP
0.016 TYP
0.320 TYP
0.013 TYP
K2
0.240 TYP
0.009 TYP
0.252 TYP
0.010 TYP
K3
0.225 TYP
0.009 TYP
K4
L
0.355 TYP
0.175
0.275
0.014 TYP
0.375
T
0.007
0.011
0.015
0.175
0.275
0.375
0.007
0.011
0.015
0.05
0.10
0.15
0.002
0.004
0.006
ECN: C-07431 − Rev. C, 06-Aug-07
DWG: 5934
Document Number: 73001
06-Aug-07
www.vishay.com
1
Application Note 826
Vishay Siliconix
RECOMMENDED PAD LAYOUT FOR PowerPAK® SC70-6L Single
0.300 (0.012)
0.650 (0.026)
0.350 (0.014)
0.275 (0.011)
0.550 (0.022)
0.475 (0.019)
2.200 (0.087)
1.500
(0.059)
0.870 (0.034)
0.235 (0.009)
0.355 (0.014)
0.350 (0.014)
1
0.650 (0.026)
0.300 (0.012)
0.950 (0.037)
Dimensions in mm/(Inches)
Return to Index
APPLICATION NOTE
Document Number: 70486
Revision: 21-Jan-08
www.vishay.com
11
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000