5962-03248

REVISIONS
LTR
DESCRIPTION
A
DATE (YR-MO-DA)
APPROVED
15-11-05
Charles F. Saffle
Redrawn. Update paragraphs to MIL-PRF-38535 requirements. Remove
class M requirements throughout. - drw
REV
SHEET
REV
A
A
A
SHEET
15
16
17
REV STATUS
REV
A
A
A
A
A
A
A
A
A
A
A
A
A
A
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Rick Officer
STANDARD
MICROCIRCUIT
DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
CHECKED BY
Rajesh Pithadia
APPROVED BY
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
Raymond Monnin
DRAWING APPROVAL DATE
03-09-30
REVISION LEVEL
A
MICROCIRCUIT, DIGITAL-LINEAR, RADIATION
HARDENED, 9 AMP NON-INVERTING 5 V LOGIC
UVLO FET DRIVER, MONOLITHIC SILICON
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
5962-03248
1 OF 17
5962-E512-15
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q) and
space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
F
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
03248
01
Q
X
C
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type. The device type identifies the circuit function as follows:
Device type
01
Generic number
Circuit function
ISL74422BRH
Radiation hardened, non-inverting 9 amp
5 V logic UVLO MOSFET driver
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
Device requirements documentation
Q or V
Certification and qualification to MIL-PRF-38535
1.2.4 Case outline. The case outline is as designated in MIL-STD-1835 as follows:
Outline letter
X
Descriptive designator
CDFP4-F16
Terminals
16
Package style
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
2
1.3 Absolute maximum ratings. 1/
Supply voltage (VS) ......................................................................................... 20 V
Input voltage range (VIN) ................................................................................ GND – 6.5 V to +VS +0.3 V 2/
DC input current, any one input (VIN ≤ VS +0.3 V or VIN ≥ GND – 6.5 V)........ 10 mA
Output short circuit duration (single supply) .................................................... Continuous 3/
Maximum power dissipation (PD) .................................................................... 625 mW
Maximum junction temperature (TJ) ................................................................
Maximum storage temperature .......................................................................
Maximum lead temperature (soldering 10 seconds) .......................................
Thermal resistance, junction-to-case (θJC) .....................................................
175°C
-65°C to +150°C
265°C
12°C/W
Thermal resistance, junction-to-ambient (θJA) ................................................ 80°C/W 4/
1.4 Recommended operating conditions.
Supply voltage range (VS) .............................................................................. 8 V to 18 V
Under voltage lockout (UVLO) ........................................................................ < 6.0 V
Operating ambient temperature range ............................................................ -55°C to +125°C
1.5 Radiation features.
Maximum total dose available: (dose rate = 50 - 300 rad(Si) / s)
Device classes Q, and V ............................................................................. 300 Krads (Si) 5/
Latch up immune ............................................................................................ 6/
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
________
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Inputs must not go more negative than GND – 6.5 V.
3/ Short circuit from the output to VS can cause excessive heating and eventual destruction.
4/
5/
6/
θJA is measured with the component mounted on an evaluation PC board in free air.
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,
method 1019, condition A.
Guaranteed by process or design.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
3
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 as specified herein, or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein.
3.1.1 Microcircuit die. For the requirements for microcircuit die, see appendix A to this document.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V.
3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.
3.2.5 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document
revision level control and shall be made available to the preparing and acquiring activity upon request.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). The certificate of compliance
submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the
manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein .
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall
be provided with each lot of microcircuits delivered to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
4
TABLE I. Electrical performance characteristics.
Test
Conditions 1/
-55°C ≤ TA ≤ +125°C
Symbol
Group A
subgroups
Device
type
1, 2, 3
01
unless otherwise specified
Power supply current, low
ISSB
Power supply current, high
ISSB
M,D,P,L,R,F 2/, 3/
IIL
1
M,D,P,L,R,F 2/, 3/
IIH
1, 2, 3
M,D,P,L,R,F 2/, 3/
Voltage output, low
VOL
VOH
1, 2, 3
VS = 18 V, IOUT = 10 mA
VIL1
VS = 8 V, limits applied
during functional test
VIH1
VS = 18 V, limits applied
during functional test
VIH2
VS = 8 V, limits applied
during functional test
M,D,P,L,R,F 2/, 3/
Functional test
FT
-10
+10
-10
+10
-10
+10
01
M,D,P,L,R,F 2/, 3/
µA
V
16.9
V
01
0.8
0.8
1, 2, 3
0.8
1
0.8
01
V
3.0
3
3.5
1
3.0
1, 2
3.0
3
3.5
1
3.0
7, 8A, 8B
VS = 8 V, VS = 18 V
µA
0.8
1
1, 2
M,D,P,L,R,F 2/, 3/
mA
16.9
1, 2, 3
M,D,P,L,R,F 2/, 3/
Input voltage, high
+10
01
1
VS = 18 V, limits applied
during functional test
mA
0.8
1, 2, 3
VS = 18 V, IOUT = 10 mA
M,D,P,L,R,F 2/, 3/
VIL2
01
-10
1
M,D,P,L,R,F 2/, 3/
Input voltage, low
01
1
M,D,P,L,R,F 2/, 3/
Voltage output, high
2.7
1
VS = 18 V, VIN = 18 V
Max
2.1
2.7
1, 2, 3
M,D,P,L,R,F 2/, 3/
Input current, high
01
1
VS = 18 V, VIN = 0 V
Unit
2.1
1, 2, 3
VS = 18 V, VIN = 10.0 V
high
Input current, low
Min
VS = 18 V, VIN = 0.8 V
low
Limits
V
01
7, 8A, 8B
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
5
TABLE I. Electrical performance characteristics – continued.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
1, 3
01
Limits
Min
Output resistance, output
high
RONH
VS = 18 V, VIN = 5.0 V,
IOUT = 175 mA to 225 mA
M,D,P,L,R,F 2/, 3/
Output resistance, output
low
RONL
IOUT = 175 mA to 225 mA
M,D,P,L,R,F 2/, 3/
UVLO versus rising
threshold
UVLO versus falling
threshold hysteresis
M,D,P,L,R,F 2/, 3/
UVLO hysteresis
(rising – falling)
tPHL
tPLH
1.7
1
1.5
6.9
7.5
2
6.6
7.2
1
6.9
7.5
6.3
6.9
2
6.0
6.6
1
6.3
6.9
01
01
TF
01
M,D,P,L,R,F 2/, 3/
V
V
0.3
01
140
175
9
140
01
ns
140
10
175
9
140
9, 11
VS = 15 V, CL = 10 nF
V
0.3
10
9, 11
VS = 18 V, CL = 10 nF
Ω
1.5
2
9, 11
VS = 18 V, CL = 10 nF
M,D,P,L,R,F 2/, 3/
Response time, fall
01
1
M,D,P,L,R,F 2/, 3/
Propagation delay, high
1.3
1, 2, 3
M,D,P,L,R,F 2/, 3/
Propagation delay, low
1
1, 3
Ω
1.3
1.5
1, 3
M,D,P,L,R,F 2/, 3/
Max
2
1, 3
VS = 18 V, VIN = 0.8 V,
Unit
01
ns
125
10
135
9
125
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
6
TABLE I. Electrical performance characteristics – continued.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
9, 11
01
Limits
Min
Response time, rise
TR
VS = 15 V, CL = 10 nF
M,D,P,L,R,F 2/, 3/
1/
2/
Unit
Max
125
10
135
9
125
ns
VS = as specified.
The devices supplied to this drawing meet all levels M, D, P, L, R, F of irradiation (classes Q, and V). However, this
device is only tested at the "F" level (classes Q, and V). Pre and Post irradiation values are identical unless otherwise
specified in Table I. When performing post irradiation electrical measurements for any RHA level, TA = +25°C.
3/
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,
method 1019, condition A.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
7
Device type
01
Case outline
X
Terminal
number
1
Terminal symbol
NC
2
NC
3
VS (LOGIC INPUT BUFFER (IB)) 1/
4
5
VIN
GND (LOGIC RTN INPUT BUFFER (IB)) 2/
6
NC
7
NC
8
GND (OUTPUT BUFFER (OB)) 3/
9
GND (OUTPUT BUFFER (OB)) 3/
10
NC
11
NC
12
-VOUT 4/
13
14
+VOUT 4/
NC
15
VS (OUTPUT BUFFER (OB)) 5/
16
VS (OUTPUT BUFFER (OB)) 5/
1/ VS (LOGIC INPUT BUFFER) pin 3 provides the supply voltage for
the control logic. It is not internally connected to pins 15 and 16
for noise immunity purposes, but it must be connected externally.
2/ GND (LOGIC RTN INPUT BUFFER) pin 5 is the control logic return.
It is not internally connected to pins 8 and 9 for noise immunity
purposes, but it must be connected externally.
3/ GND (OUTPUT BUFFER) pins 8 and 9 must be connected to GND.
4/ VOUT pins 12 and 13 must be externally connected.
5/ VS (OUTPUT BUFFER) pins 15 and 16 must be connected to VS.
FIGURE 1. Terminal connections.
INPUT
OUTPUT
1
1
0
0
FIGURE 2. Truth table.
FIGURE 3. Logic diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
8
4. VERIFICATION
4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with
MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan
shall not affect the form, fit, or function as described herein.
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted
on all devices prior to qualification and technology conformance inspection.
4.2.1 Additional criteria for device classes Q and V.
a.
The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the
device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under
document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
b.
Interim and final electrical test parameters shall be as specified in table IIA herein.
c.
Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B.
4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in
accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups
A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
MIL-PRF-38535 including groups A, B, C, D, and E inspections, and as specified herein.
4.4.1 Group A inspection.
a.
Tests shall be as specified in table IIA herein.
b.
Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
c.
For device classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
9
TABLE IIA. Electrical test requirements.
Subgroups
(in accordance with
MIL-PRF-38535, table III)
Device
Device
class Q
class V
Test requirements
Interim electrical
parameters (see 4.2)
Final electrical
parameters (see 4.2)
Group A test
requirements (see 4.4)
Group C end-point electrical
parameters (see 4.4)
Group D end-point electrical
parameters (see 4.4)
Group E end-point electrical
parameters (see 4.4)
1, 7
1, 7
1, 2, 3, 7, 8A, 8B,
9, 10, 11 1/
1, 2, 3, 7, 8A, 8B,
9, 10, 11 2/, 3/
1, 2, 3, 7, 8A, 8B,
9, 10, 11
1, 2, 3, 7, 8A, 8B,
9, 10, 11
1, 2, 3, 7, 8A, 8B,
9, 10, 11
1, 2, 3, 7, 8A, 8B,
9, 10, 11 3/
1, 7, 9
1, 7, 9
1, 7, 9
1, 7, 9
1/ PDA applies to subgroup 1.
2/ PDA applies to subgroups 1, 7, and ∆’s.
3/ Delta limits (see table IIB herein) shall be required and the delta values shall be computed with
reference to the zero hour electrical parameters (see table I herein).
TABLE IIB. Burn-in and life test delta parameters. TA = +25°C
Parameters
Symbol
Power supply current, low
Min
Max
Unit
ISSB low
200
µA
Power supply current, high
ISSB high
200
µA
Input current, low
IIL
1
µA
Input current, high
IIH
1
µA
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.2.1 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The
test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of
MIL-STD-883.
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
10
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
(see 3.5 herein). RHA levels for device classes M, Q and V shall be as specified in MIL-PRF-38535 and the end-point electrical
parameters shall be as specified in table IIA herein. The end-point electrical parameters shall be as specified in table I group A
subgroups or as modified in the QM plan.
4.4.4.1 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883
method 1019, condition A and as specified herein.
4.4.4.1.1 Accelerated annealing test. Accelerated annealing tests shall be performed on all devices requiring a RHA level
greater than 5k rads(Si). The post-anneal end-point electrical parameter limits shall be as specified in table I herein and shall be
the pre-irradiation end-point electrical parameter limit at 25°C ±5°C. Testing shall be performed at initial qualification and after
any design or process changes which may affect the RHA response of the device.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes
Q and V.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
prepared specification or drawing.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires
configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and
this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic
devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108.
6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-0540.
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331.
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in
MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have submitted a certificate of
compliance (see 3.6 herein) to DLA Land and Maritime-VA and have agreed to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
11
APPENDIX A
APPENDIX A FORMS A PART OF SMD 5962-03248
A.1 SCOPE
A.1.1 Scope. This appendix establishes minimum requirements for microcircuit die to be supplied under the Qualified
Manufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturers
approved QM plan for use in monolithic microcircuits, multi-chip modules (MCMs), hybrids, electronic modules, or devices using
chip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting of
military high reliability (device class Q) and space application (device class V) are reflected in the Part or Identification Number
(PIN). When available, a choice of Radiation Hardiness Assurance (RHA) levels are reflected in the PIN.
A.1.2 PIN. The PIN is as shown in the following example:
5962
F
Federal
stock class
designator
\
RHA
designator
(see A.1.2.1)
03248
01
V
9
A
Device
type
(see A.1.2.2)
Device
class
designator
(see A.1.2.3)
Die
code
Die
details
(see A.1.2.4)
/
\/
Drawing number
A.1.2.1 RHA designator. Device classes Q and V RHA identified die meet the MIL-PRF-38535 specified RHA levels. A dash
(-) indicates a non-RHA die.
A.1.2.2 Device type. The device type identifies the circuit function as follows:
Device type
01
Generic number
Circuit function
ISL74422BRH
Radiation hardened non-inverting 9 amp
5 V logic UVLO MOSFET driver
A.1.2.3 Device class designator.
Device class
Q or V
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
Device requirements documentation
Certification and qualification to the die requirements of MIL-PRF-38535
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
12
APPENDIX A
APPENDIX A FORMS A PART OF SMD 5962-03248
A.1.2.4 Die details. The die details designation is a unique letter which designates the die's physical dimensions, bonding
pad locations and related electrical functions, interface materials, and other assembly related information, for each product and
variant supplied to this appendix.
A.1.2.4.1 Die physical dimensions.
Die type
Figure number
01
A-1
A.1.2.4.2 Die bonding pad locations and electrical functions.
Die type
Figure number
01
A-1
A.1.2.4.3 Interface materials.
Die type
Figure number
01
A-1
A.1.2.4.4 Assembly related information.
Die type
Figure number
01
A-1
A.1.3 Absolute maximum ratings. See paragraph 1.3 herein for details.
A.1.4 Recommended operating conditions. See paragraph 1.4 herein for details.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
13
APPENDIX A
APPENDIX A FORMS A PART OF SMD 5962-03248
A.2 APPLICABLE DOCUMENTS.
A.2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARD
MIL-STD-883 - Test Method Standard Microcircuits.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
A.2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the
text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
A.3 REQUIREMENTS
A.3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer’s Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein.
A.3.2 Design, construction and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein and the manufacturer’s QM plan for device classes Q and V.
A.3.2.1 Die physical dimensions. The die physical dimensions shall be as specified in A.1.2.4.1 and on figure A-1.
A.3.2.2 Die bonding pad locations and electrical functions. The die bonding pad locations and electrical functions shall be as
specified in A.1.2.4.2 and on figure A-1.
A.3.2.3 Interface materials. The interface materials for the die shall be as specified in A.1.2.4.3 and on figure A-1.
A.3.2.4 Assembly related information. The assembly related information shall be as specified in A.1.2.4.4 and on figure A-1.
A.3.2.5 Truth table. The truth table shall be as defined in paragraph 3.2.3 herein.
A.3.2.6 Logic diagram. The logic diagram shall be as defined in paragraph 3.2.4 herein.
A.3.2.7 Radiation exposure circuit. The radiation exposure circuit shall be as defined in paragraph 3.2.5 herein.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
14
APPENDIX A
APPENDIX A FORMS A PART OF SMD 5962-03248
A.3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and post-irradiation parameter limits are as specified in table I of the body of this
document.
A.3.4 Electrical test requirements. The wafer probe test requirements shall include functional and parametric testing
sufficient to make the packaged die capable of meeting the electrical performance requirements in table I.
A.3.5 Marking. As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a
customer, shall be identified with the wafer lot number, the certification mark, the manufacturer’s identification and the PIN listed
in A.1.2 herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535.
A.3.6 Certification of compliance. For device classes Q and V, a certificate of compliance shall be required from a
QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see A.6.4 herein). The certificate of
compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply for this appendix shall
affirm that the manufacturer’s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the
requirements herein.
A.3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535
shall be provided with each lot of microcircuit die delivered to this drawing.
A.4 VERIFICATION
A.4.1 Sampling and inspection. For device classes Q and V, die sampling and inspection procedures shall be in accordance
with MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan. The modifications in the QM
plan shall not affect the form, fit, or function as described herein.
A.4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in the
manufacturer’s QM plan. As a minimum, it shall consist of:
a.
Wafer lot acceptance for class V product using the criteria defined in MIL-STD-883, method 5007.
b.
100% wafer probe (see paragraph A.3.4 herein).
c.
100% internal visual inspection to the applicable class Q or V criteria defined in MIL-STD-883, method 2010 or the
alternate procedures allowed in MIL-STD-883, method 5004.
A.4.3 Conformance inspection.
A.4.3.1 Group E inspection. Group E inspection is required only for parts intended to be identified as radiation assured (see
A.3.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing of
packaged die shall be as specified in table IIA herein. Group E tests and conditions are as specified in paragraphs 4.4.4, 4.4.4.1
and 4.4.4.1.1 herein.
A.5 DIE CARRIER
A.5.1 Die carrier requirements. The requirements for the die carrier shall be accordance with the manufacturer’s QM plan or
as specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical and
electrostatic protection.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
15
APPENDIX A
APPENDIX A FORMS A PART OF SMD 5962-03248
A.6 NOTES
A.6.1 Intended use. Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance with
MIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications, and
logistics purposes.
A.6.2 Comments. Comments on this appendix should be directed to DLA Land and Maritime -VA, Columbus, Ohio, 432183990 or telephone (614)-692-0540.
A.6.3 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331.
A.6.4 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in
MIL-HDBK-103 and QML-38535. The vendors listed within MIL-HDBK-103 and QML-38535 have submitted a certificate of
compliance (see A.3.6 herein) to DLA Land and Maritime -VA and have agreed to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
16
APPENDIX A
APPENDIX A FORMS A PART OF SMD 5962-03248
Die bonding pad locations and electrical functions
Die physical dimensions.
Die size: 4191 microns x 4826 microns
Die thickness: 19 ± 1 mils
Interface materials.
Top metallization: Al Si Cu 16.0 kÅ ± 2 kÅ
Backside metallization: None
Glassivation.
Type: PSG
Thickness: 8.0 kÅ ± 1.0 kÅ
Substrate: DI (dielectric isolation)
Assembly related information.
Substrate potential: Unbiased
Special assembly instructions: See figure 1 terminal connections.
FIGURE A-1. Die bonding pad locations and electrical functions.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-03248
A
REVISION LEVEL
A
SHEET
17
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 15-11-05
Approved sources of supply for SMD 5962-03248 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962F0324801QXC
34371
ISL74422BRHQF
5962F0324801VXC
34371
ISL74422BRHVF
5962F0324801V9A
34371
ISL74422BRHVX
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE
number
34371
Vendor name
and address
Intersil Corporation
1650 Robert J. Conlan Blvd. NE
Palm Bay, FL 32905-3406
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.