LT3086 - 40V, 2.1A Low Dropout Adjustable Linear Regulator with Monitoring and Cable Drop Compensation

LT3086
40V, 2.1A Low Dropout
Adjustable Linear Regulator with Monitoring
and Cable Drop Compensation
Description
Features
Wide Input Voltage Range: 1.4V to 40V
n1 Resistor Sets Output Voltage: 0.4V to 32V
n Output Current: 2.1A
n±2% Tolerance Over Line, Load and Temperature
n Output Current Monitor: I
MON = IOUT/1000
n Temperature Monitor with Programmable
Thermal Limit
n Programmable Cable Drop Compensation
n Parallel Multiple Devices for Higher Current
n Dropout Voltage: 330mV
n1 Capacitor Soft-Starts Output and Decreases Noise
n Low Output Noise: 40µV
RMS (10Hz to 100kHz)
n Precision, Programmable External Current Limit
n Power Good Flag with Programmable Threshold
n Ceramic Output Capacitors: 10µF Minimum
n Quiescent Current in Shutdown: <1µA
n Reverse-Battery, -Current and -Output Protection
n Available in 5mm × 4mm 16-Lead DFN,
16-Lead TSSOP, 7-Lead DD-Pak and 7-Lead TO-220.
n
Applications
n
n
n
n
Programmable Linear Regulator
Post Regulator for Switching Supplies
USB Power Supplies
High Reliability Power Supplies
The LT®3086 is a multi-feature, low dropout, low noise
2.1A linear regulator that operates over a 1.4V to 40V
input supply range. Dropout voltage at 2.1A is typically
330mV. One resistor sets output voltage from 0.4V to 32V.
Output voltage tolerance is guaranteed to ±2% over line,
load and temperature. The LT3086 is stable with ceramic
output capacitors, requiring a minimum of 10µF.
The LT3086’s programmable cable drop compensation
cancels output voltage errors caused by resistive connections to the load. A master/slave configuration allows paralleling of multiple devices for higher load current and heat
spreading without external ballast resistor requirements.
Output current and temperature monitoring along with
a power good flag provide system diagnostic and debug
capability. Internal fault circuitry includes thermal shutdown
and current limit with foldback. Thermal limit and current
limit are also externally programmable.
Packages include the thermally enhanced 16-lead
(5mm × 4mm) DFN, 16-lead TSSOP, 7-lead DD-Pak and
7-lead TO-220.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Typical Application
Transient Response with Cable
Drop Compensation (CDC)
5V, 2.1A USB Supply with Cable Drop Compensation
RCDC =
RMON
357Ω
1%
SET
TEMP
TRACK
IMON
ILIM
RMON •RSET
3000 •R WIRE
R WIRE = RLINE1 +RLINE2 *
CDC
RPWRGD
PWRGD
GND
RCDC
1%
OUTPUT VOLTAGE (V)
SHDN
RSET
90.9k + 1.1k
1%
5.6
82.5k 10µF
1%
100k
RCDC 1%
VLOAD
5V AT 2.1A
VPWRGD
RLINE2
*SEE APPLICATIONS INFORMATION
FOR INDUCTANCE EFFECTS ASSOCIATED
WITH RWIRE
3086 TA01
LOAD
CURRENT (A)
TO ADC
0.8V AT 2.24A
FULL-SCALE
LT3086
10µF
VTEMP
10mV/°C
25°C = 250mV
OUT
5.8
CABLE
RLINE1
LOAD
VIN
6V TO
15V
IN
VOUT
5.4
VOUT WITH CDC
5.2
5.0
VIN = 6V
RMON = 357Ω
RWIRE = 0.24Ω
RCDC = 46.4k
VLOAD WITH CDC
4.8
4.6
VLOAD WITHOUT CDC
4.4
4.2
∆ILOAD = 0.5A TO 1.5A
2
1
0
0
80 160 240 320 400 480 560 640 720 800
TIME (µs)
3060 TA04b
3086fa
For more information www.linear.com/LT3086
1
LT3086
Absolute Maximum Ratings
(Note 1)
IN Pin Voltage..........................................................±45V
OUT Pin Voltage.......................................................±36V
Input-to-Output Differential Voltage (Note 2)...........±45V
SET Pin Voltage................................................–0.3, 36V
SHDN Pin Voltage....................................................±45V
CDC Pin (Internally Clamped, Current into Pin)........<8mA
IMON Pin Voltage.................................................–0.3, 7V
ILIM Pin Voltage...................................................–0.3, 2V
TRACK Pin Voltage..... –0.3, Internally Clamped at 1.25V
TEMP Pin Voltage..................................................0V, 5V
PWRGD Pin Voltage..........................................–0.3, 36V
RPWRGD Pin Voltage..........................................–0.3, 36V
Output Short-Circuit Duration........................... Indefinite
Operating Junction Temperature (Notes 3, 5, 12)
E-Grade, I-Grade................................. –40°C to 125°C
MP-Grade........................................... –55°C to 125°C
Storage Temperature Range.......................–65 to 150°C
Lead Temperature (Soldering, 10 sec)
(TSSOP, DD-Pak, TO-220 Only) ............................ 300°C
Pin Configuration
TOP VIEW
TOP VIEW
GND
1
16 GND
GND
1
16 GND
IMON/ILIM
2
15 PWRGD
CDC
3
14 TRACK
ILIM
2
15 PWRGD
IMON
3
14 TRACK
CDC
4
13 TEMP
RPWRGD
4
RPWRGD
5
12 SHDN
SET
5
17
GND
17
GND
13 TEMP
12 SHDN
SET
6
11 IN
OUT
6
11 IN
OUT
7
10 IN
OUT
7
10 IN
OUT
8
9
GND
8
9
NC
GND
DHD PACKAGE
16-LEAD (5mm × 4mm) PLASTIC DFN
TJMAX = 125°C, θJA = 25°C/W TO 33°C/W*, θJC = 4.3°C/W
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
FE PACKAGE
16-LEAD PLASTIC TSSOP
TJMAX = 125°C, θJA = 25°C/W TO 33°C/W*, θJC = 10°C/W
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
FRONT VIEW
FRONT VIEW
TAB
IS
GND
7
6
5
4
3
2
1
TEMP
SHDN
IN
GND
OUT
SET
IMON/ILIM
TAB
IS
GND
R PACKAGE
7-LEAD PLASTIC DD
TJMAX = 125°C, θJA = 15°C/W TO 19°C/W*, θJC = 3°C/W
7
6
5
4
3
2
1
TEMP
SHDN
IN
GND
OUT
SET
IMON/ILIM
T7 PACKAGE
7-LEAD PLASTIC TO-220
TJMAX = 125°C, θJA = 34°C/W, θJC = 3°C/W
*See Applications Information section.
2
3086fa
For more information www.linear.com/LT3086
LT3086
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3086EDHD#PBF
LT3086EDHD#TRPBF
3086
16-Lead (5mm × 4mm) Plastic DFN
–40°C to 125°C
LT3086IDHD#PBF
LT3086IDHD#TRPBF
3086
16-Lead (5mm × 4mm) Plastic DFN
–40°C to 125°C
LT3086EFE#PBF
LT3086EFE#TRPBF
3086FE
16-Lead Plastic TSSOP
–40°C to 125°C
LT3086IFE#PBF
LT3086IFE#TRPBF
3086FE
16-Lead Plastic TSSOP
–40°C to 125°C
LT3086MPFE#PBF
LT3086MPFE#TRPBF
3086FE
16-Lead Plastic TSSOP
–55°C to 125°C
LT3086ER#PBF
LT3086ER#TRPBF
LT3086R
7-Lead Plastic DD-Pak
–40°C to 125°C
LT3086IR#PBF
LT3086IR#TRPBF
LT3086R
7-Lead Plastic DD-Pak
–40°C to 125°C
LT3086MPR#PBF
LT3086MPR#TRPBF
LT3086R
7-Lead Plastic DD-Pak
–55°C to 125°C
LT3086ET7#PBF
N/A
LT3086T7
7-Lead Plastic TO-220
–40°C to 125°C
LT3086IT7#PBF
N/A
LT3086T7
7-Lead Plastic TO-220
–40°C to 125°C
LT3086MPT7#PBF
N/A
LT3086T7
7-Lead Plastic TO-220
–55°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C.
PARAMETER
CONDITIONS
MIN
Minimum Input Voltage (Note 4)
ILOAD = 2.1A, ∆VOUT = –1%
l
TYP
MAX
UNITS
1.4
1.55
V
Reference Voltage
(Notes 3, 5)
VSET
VIN = 1.55V, ILOAD = 1mA
1.55V < VIN < 40V, 1mA < ILOAD < 2.1A
l
396
392
400
400
404
408
mV
mV
Reference Current
ISET
VIN = 1.55V, ILOAD = 1mA
1.55V < VIN < 40V, 1mA < ILOAD < 2.1A
l
49.5
49
50
50
50.5
51
µA
µA
Line Regulation
VSET
ISET
VIN = 1.55V to 40V, ILOAD = 1mA
l
l
–0.12
0.1
–0.03
0.8
mV
µA
Load Regulation
(Notes 6, 7)
VSET
ISET
ILOAD = 1mA to 2.1A, VIN = VOUT + 0.55V
l
l
0.25
0.02
1
0.08
mV
µA
1
mA
10
65
100
mV
mV
100
135
160
mV
mV
150
195
235
mV
mV
260
335
425
mV
mV
330
415
540
mV
mV
1.2
1.3
1.8
4.5
23
44
2.4
2.6
3.6
9
46
88
mA
mA
mA
mA
mA
mA
Minimum Load Current (Note 16)
Dropout Voltage
VIN = VOUT(NOMINAL), (Notes 7, 8)
l
ILOAD = 1mA
ILOAD = 100mA
ILOAD = 500mA
ILOAD = 1.5A
ILOAD = 2.1A
GND Pin Current
VIN = VOUT(NOMINAL) + 0.55V, (Notes 7, 9)
ILOAD = 0µA
ILOAD = 1mA
ILOAD = 100mA
ILOAD = 500mA
ILOAD = 1.5A
ILOAD = 2.1A
l
l
l
l
l
l
l
l
l
l
l
3086fa
For more information www.linear.com/LT3086
3
LT3086
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C.
PARAMETER
CONDITIONS
MIN
TYP
MAX
Quiescent Current in Shutdown
Output Voltage Noise
VIN = 40V, VSHDN = 0V
0.1
1
CSET = 0.01µF , COUT = 10µF, ILOAD = 2.1A
VOUT = 5V, BW = 10Hz to 100kHz
40
Shutdown Threshold
VOUT = Off to On
VOUT = On to Off
l
l
SHDN Pin Current (Note 10)
1.55V < VIN < 40V
VSHDN = 0V
VSHDN = 40V
l
l
TEMP Voltage (Note 13)
TJ = 25°C
TJ = 125°C
TEMP Error (Note 13)
0°C < TJ < 125°C, ITEMP = 0
0°C < TJ < 125°C, ITEMP = 0µA to 80µA
ITEMP Thermal Limit Current Threshold
25°C < TJ < 125°C
IMON Output Current
VIN = VOUT(NOMINAL) + 0.55V (Note 15)
ILOAD = 20mA, RMON = 1kΩ
ILOAD = 500mA, RMON = 330Ω
ILOAD = 1A, RMON = 330Ω
ILOAD = 1.5A, RMON = 330Ω
ILOAD = 2.1A, RMON = 330Ω
Output Current Sharing Error (Note 14)
RMON = 330Ω, IOUT(MASTER) = 2.1A
TRACK Pin Pull-Up Current
VTRACK = 750mV
l
RPWRGD Reference Voltage
1.55V < VIN < 40V
RPWRGD Reference Current
1.55V < VIN < 40V
RPWRGD Reference Voltage Hysteresis
1.55V < VIN < 40V
RPWRGD Reference Current Hysteresis
1.55V < VIN < 40V
PWRGD VOL
IPWRGD = 200µA (Fault Condition)
l
PWRGD Internal Time Delay
VOL TO VOH (Rising Edge)
l
PWRGD Pin Leakage Current
VPWGRD = 32V, VRPWGRD = 500mV
l
CDC Reference Voltage
1.55V < VIN < 40V, IMON = 0V
1.12
0.85
1.22
1.03
15
l
l
l
l
l
µA
µVRMS
1.32
V
V
1
35
µA
µA
0.25
1.25
–0.09
–0.1
UNITS
V
V
0.09
V
V
95
100
105
µA
5
440
0.95
1.43
2.02
20
500
1.00
1.50
2.10
75
560
1.05
1.57
2.18
µA
µA
mA
mA
mA
–10
0
10
%
7
15
25
µA
l
390
400
410
mV
l
48.75
50
51.25
µA
2.4
mV
300
nA
55
200
mV
8
17
25
µs
1
µA
l
390
400
410
mV
l
0.320
0.333
0.343
V/V
65
80
CDC/VIMON Voltage Gain
1.55V < VIN < 40V, 0 < ICDC < 20µA, VIMON = 800mV to 0
Ripple Rejection
VIN = 1.9V (AVG), VRIPPLE = 0.5VP-P, VOUT = 1V
fRIPPLE = 120Hz, ILOAD = 2.1A
Internal Current Limit
VIN = 1.55V
VIN = VOUT(NOMINAL) + 0.55V (Notes 7, 12), ∆VOUT = –5%
l
l
2.2
2.2
2.4
2.9
A
A
ILIM Threshold Voltage
1.55V < VIN < 40V
l
775
800
825
mV
Input Reverse-Leakage Current
VIN = –40V, VOUT = 0
l
2
mA
Reverse-Output Current (Note 11)
VOUT = 32V, VIN = 0, VSHDN = 0
10
µA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Absolute maximum input-to-output differential voltage is not
achievable with all combinations of rated IN pin and OUT pin voltages.
With the IN pin at 45V, the OUT pin may not be pulled below 0V. The total
IN to OUT differential voltage must not exceed ±45V.
Note 3: The LT3086 is tested and specified under pulse load conditions
such that TJ ≅ TA. The LT3086E is 100% production tested at TA = 25°C
and performance is guaranteed from 0°C to 125°C. Performance at –40°C
to 125°C is assured by design, characterization and correlation with
statistical process controls. The LT3086I is guaranteed over the full –40°C
4
1
dB
to 125°C operating junction temperature range. The LT3086MP is 100%
tested over the –55°C to 125°C operating junction temperature range.
Note 4: The LT3086 is tested and specified for these conditions with the
SET pin connected to the OUT pin, VOUT = 0.4V.
Note 5: Maximum junction temperature limits operating conditions. The
regulated output voltage specification does not apply for all possible
combinations of input voltage and output current. Limit the output current
range if operating at large input-to-output voltage differentials. Limit
the input-to-output voltage differential if operating at maximum output
current. Current limit foldback limits the maximum output current as a
function of input-to-output voltage. See Current Limit vs VIN – VOUT in the
Typical Performance Characteristics section.
Note 6: Load regulation is Kelvin-sensed at the package.
3086fa
For more information www.linear.com/LT3086
LT3086
Electrical Characteristics
Note 7: To satisfy minimum input voltage requirements, the LT3086 is
tested and specified for these conditions with a 32k resistor between OUT
and SET for a 2V output voltage.
Note 8: Dropout voltage is the minimum input-to-output voltage
differential needed to maintain regulation at a specified output current.
In dropout, the output voltage equals: (VIN – VDROPOUT). For low output
voltages and certain load conditions, minimum input voltage requirements
limit dropout voltage. See the Minimum Input Voltage curve in the Typical
Performance Characteristics section.
Note 9: GND pin current is tested with VIN = VOUT(NOMINAL) + 0.55V and
PWRGD pin floating. GND pin current increases in dropout. See GND pin
current curves in the Typical Performance Characteristics section.
Note 10: SHDN pin current flows into the SHDN pin.
Note 11: Reverse-output current is tested with the IN pin grounded and
the OUT pin forced to a voltage. The current flows into the OUT pin and out
of the GND pin.
Note 12: The IC includes overtemperature protection circuitry that protects
the device during momentary overload conditions. Junction temperature
exceeds 125°C when the overtemperature circuitry is active unless thermal
limit is externally set below 125°C by loading the TEMP pin. Continuous
operation above the specified maximum junction temperature may impair
device reliability.
Note 13: The TEMP output voltage represents the average die temperature
next to the power transistor while the center of the transistor can be
significantly hotter during high power conditions. Due to power dissipation
and temperature gradients across the die, the TEMP output voltage
measurement does not guarantee that absolute maximum junction
temperature is not exceeded.
Note 14: Output current sharing error is the difference in output currents
of a slave relative to its master when two LT3086 regulators are paralleled.
The device is tested as a slave with VTRACK = 0.693V, RMON = 330Ω
and VSET = 0.4V, conditions when an ideal master is outputting 2.1A.
The specification limits account for the slave output tracking error from
2.1A and the worst-case error that can be contributed by a master: the
maximum deviation of VSET from 0.4V and IMON from 2.1mA.
Note 15: The LT3086 is tested and specified for these conditions with the
IMON and ILIM pins tied together.
Note 16: The LT3086 requires a minimum load current to ensure proper
regulation and stability.
Typical Performance Characteristics
Typical Dropout Voltage
Guaranteed Dropout Voltage
550
500
500
DROPOUT VOLTAGE (mV)
450
400
350
TJ = 125°C
250
TJ = 25°C
200
150
100
50
0
0
0.3
0.6 0.9 1.2 1.5
OUTPUT CURRENT (A)
1.8
2.1
3086 G01
Dropout Voltage
550
= TEST POINTS
500
450
450
400
DROPOUT VOLTAGE (mV)
GUARANTEED DROPOUT VOLTAGE (mV)
550
300
TA = 25°C, unless otherwise noted.
TJ ≤ 125°C
350
300
TJ ≤ 25°C
250
200
150
400
350
300
200
150
100
50
50
0
0.3
0.6 0.9 1.2 1.5
OUTPUT CURRENT (A)
1.8
2.1
3086 G02
IL = 1.5A
IL = 1A
250
100
0
IL = 2.1A
IL = 500mA
IL = 100mA
IL = 1mA
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G03
3086fa
For more information www.linear.com/LT3086
5
LT3086
Typical Performance Characteristics
SET Pin Reference Voltage
SET Pin Reference Current
51.0
404
402
400
398
396
394
392
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
Quiescent Current
2.0
IL = 1mA
50.8
50.6
QUIESCENT CURRENT (mA)
IL = 1mA
406
SET PIN REFERENCE CURRENT (µA)
50.4
50.2
50.0
49.8
49.6
49.4
49.2
3086 G04
2.0
VSHDN = VIN
1.2
1.0
0.8
0.6
0.4
0.2
0
5
10
1.4
1.2
VSHDN = VIN
1.0
0.8
0.6
35
0
40
0
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
GND PIN CURRENT (mA)
GND PIN CURRENT (mA)
50
RL = 0.19Ω, IL = 2.1A
RL = 0.267Ω, IL = 1.5A
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
9
10
3086 G10
6
6
4
3
RL = 4Ω
IL = 100mA
RL = 400Ω, IL = 1mA
0
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
5
0
RL = 50Ω
IL = 100mA
3086 G09
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
9
TJ = 25°C
80 VSHDN = VIN
RSET = 92k
70
60
RL = 2.381Ω
IL = 2.1A
50
40
RL = 3.333Ω
IL = 1.5A
30
20
10
RL = 5k, IL = 1mA
0
10
90
4
3
9
GND Pin Current, VOUT = 5V
(Heavy Load)
RL = 10Ω
IL = 500mA
1
8
RL = 0.8Ω
IL = 500mA
5
0
10
7
2
RL = 0.4Ω, IL = 1A
0
9
TJ = 25°C
9 VSHDN = VIN
RSET = 92k
8
60
0
6
1
VSHDN = 0
10
TJ = 25°C
80 VSHDN = VIN
RSET = 0
70
10
7
GND Pin Current, VOUT = 5V
(Light Load)
90
20
TJ = 25°C
9 VSHDN = VIN
RSET = 0
8
3086 G08
GND Pin Current, VOUT = 0.4V
(Heavy Load)
30
0.4
2
3086 G07
40
0.6
10
0.4
0.2
15 20 25 30
INPUT VOLTAGE (V)
0.8
GND Pin Current, VOUT = 0.4V
(Light Load)
TJ = 25°C
RSET = 92k
IL = 0
1.6
VSHDN = 0
0
1.0
3086 G06
Quiescent Current, VOUT = 5V
1.8
1.4
1.2
VSHDN = 0
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
GND PIN CURRENT (mA)
Quiescent Current, VOUT = 0.4V
TJ = 25°C
1.8 RSET = 0
IL = 0
1.6
VSHDN = VIN
1.4
3086 G05
QUIESCENT CURRENT (mA)
QUIESCENT CURRENT (mA)
2.0
VIN = 6V
1.8 VOUT = 5V
IL = 0
1.6
0.2
49.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
GND PIN CURRENT (mA)
SET PIN REFERENCE VOLTAGE (mV)
408
TA = 25°C, unless otherwise noted.
10
3086 G11
0
RL = 5Ω, IL = 1A
0
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
9
10
3086 G12
3086fa
For more information www.linear.com/LT3086
LT3086
Typical Performance Characteristics
GND Pin Current vs ILOAD
70
GND Pin Current vs Temperature
70
VIN = VOUT(NOMINAL) + 0.55V
VIN = VOUT(NOMINAL) + 0.55V
1.35
–40°C
30
25°C
125°C
20
IL = 2.1A
40
30
IL = 1.5A
20
IL = 1A
10
0
0.3
0.6 0.9 1.2 1.5
OUTPUT CURRENT (A)
1.8
3086 G13
SHDN PIN INPUT CURRENT (µA)
14
12
10
8
6
4
VSHDN = 40V
16
14
12
10
8
VSHDN = 6V
6
4
2
2
0
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
10 15 20 25 30
SHDN PIN VOLTAGE (V)
35
40
408
RPWRGD Pin Threshold
IL = 0
404
OUTPUT RISING
400
398
1.10
ON TO OFF
1.05
1.00
SHDN TIED TO VIN
VSHDN ≤ VIN – 0.3V, VIN > VIN(MIN)
0.90
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G14
300
275
250
225
ON TO OFF
200
175
150
OFF TO ON
125
100
75
50
25
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G17
RPWRGD Pin Input Current
51.0
406
402
1.15
3086 G16
3086 G15
RPWRGD PIN INPUT CURRENT (µA)
5
RPWRGD PIN THRESHOLD (mV)
0
1.20
OUT Over IN Shutdown Threshold
18
16
OFF TO ON
1.25
SHDN Pin Input Current
20
VIN = VSHDN
18
1.30
0.95
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G13a
2.1
SHDN Pin Input Current
20
IL = 500mA
OUT OVER IN SHUTDOWN THRESHOLD (mV)
40
50
SHDN PIN THRESHOLD (V)
50
10
SHDN PIN INPUT CURRENT (µA)
SHDN Pin Threshold
1.40
60
GND PIN CURRENT (mA)
GND PIN CURRENT (mA)
60
0
TA = 25°C, unless otherwise noted.
OUTPUT FALLING
396
394
392
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G18
50.8
IL = 0
50.6
50.4
50.2
OUTPUT RISING
50.0
49.8
49.6
OUTPUT FALLING
49.4
49.2
49.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G19
3086fa
For more information www.linear.com/LT3086
7
LT3086
Typical Performance Characteristics
PWRGD Output Low Voltage
160
140
120
100
80
60
40
20
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
IPWRGD = 200µA
21 V TO V
OL
OH
20
1050
1040
19
IOUT/IMON RATIO (A/A)
IPWRGD = 200µA
18
17
16
15
14
13
20
15
IL = 0
10
940
10
820
8
815
6
810
805
800
795
790
785
8
0.24
6
0.23
–6
TRACK = 400mV
–8
0
–2
–4
–10
3086 G26
0
0.18
100 200 300 400 500 600 700 800
ILIM PIN VOLTAGE (mV)
3086 G25
TRACK Pin Pull-Up Current
TRACK = 750mV
TRACK = 0mV
TRACK = 400mV
0.17
0.16
–10
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
8
2
30
0.21
0.19
2.1
–8
0.22
0.20
1.8
4
TRACK Amplifier Gain
0.25
TRACK AMPLIFIER GAIN (V/V)
TRACK AMPLIFIER INPUT OFFSET (mV)
TRACK Amplifier Input Offset
TRACK = 0mV
0.6 0.9 1.2 1.5
OUTPUT CURRENT (A)
ILIM Pin Input Current
3086 G24
10
–2
0.3
–6
3086 G23
TRACK = 750mV
0
3086 G22
825
775
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
–4
970
950
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
4
TJ = 25°C
980
10
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
780
0
990
960
5
2
1000
ILIM PIN CURRENT (µA)
ILIM PIN THRESHOLD (mV)
CURRENT MONITOR (VIMON/RMON) (µA)
IL = 20mA
TJ = –40°C
1010
ILIM Pin Threshold Voltage
30
IMON = VIMON/RMON
IMON TIED TO ILIM
RMON = 330Ω
VIN = VOUT + 0.55V
3086 G21
IMON TIED TO ILIM
RMON = 1kΩ
VIN = VOUT + 0.55V
35
1020
11
Current Monitor at Light Load
40
TJ = 125°C
1030
12
3086 G20
25
IOUT/IMON Ratio
1060
0.15
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G27
TRACK PIN PULL-UP CURRENT (µA)
180
PWRGD Internal Time Delay
22
PWRGD INTERNAL TIME DELAY (µs)
PWRGD OUTPUT LOW VOLTAGE (mV)
200
TA = 25°C, unless otherwise noted.
25
20
15
10
5
0
0
0.2
0.4 0.6 0.8 1.0
TRACK PIN VOLTAGE (V)
1.2
1.4
3086 G28
3086fa
For more information www.linear.com/LT3086
LT3086
Typical Performance Characteristics
TRACK Pin Pull-Up Current
CDC Pin Reference Voltage
TRACK = 0
20
15
TRACK = 750mV
10
5
VIMON = 800mV TO 0mV
0.341 RCDC = ∞
RCDC = ∞
406 RMON = 0
IL = 0
CDC/VIMON VOLTAGE GAIN (V/V)
25
404
402
400
398
396
394
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0.337
0.335
TJ = 25°C
0.331
TJ = 125°C
0.329
0.327
0.329
0.327
0.323
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G31
TJ = –40°C
2.0
TJ = 25°C
TJ = –40°C
3
2
0
1.0
0.5
3.0
TEMP = VTEMP/(10mV/°C)
–1.0
–2.0
0
1
2
3 4 5 6 7
CDC PIN VOLTAGE (V)
8
9
10
–2.5
1.8
1.5
1.2
0.9
0.6
96
0.3
95
0
25
50
75
100
125
TEMPERATURE (°C)
CURRENT LIMIT (A)
2.1
CURRENT LIMIT (A)
2.4
2.1
FALLING
150
3086 G35
TJ = –40°C
TJ = 25°C
0
150
VIN = 1.55V
2.7 VOUT = 0V
2.4
97
75
100
125
TEMPERATURE (°C)
3.0
∆VOUT = –5%
102
98
50
Internal Current Limit
vs Temperature
103
99
25
3086 G34
Internal Current Limit
vs VIN – VOUT
2.7
RISING
ITEMP = 80µA
–0.5
3086 G33
ITEMP Thermal Limit Threshold
100
ITEMP = 0
0
–1.5
TJ = 125°C
3086 G32
101
TEMP = VTEMP/(10mV/°C)
1.5
4
0.323
10 20 30 40 50 60 70 80 90 100
RCDC (kΩ)
TEMP Pin Error
VOUT > VOUT(NOMINAL)
5
1
THERMAL LIMIT THRESHOLD (µA)
0.331
2.5
6
0.325
0
0.333
TEMP PIN ERROR (°C)
0.339
CDC PIN CURRENT (mA)
CDC/VIMON VOLTAGE GAIN (V/V)
8
7
0.333
0.335
CDC Pin Internal Clamp Fault
Current
VIMON = 800mV TO 0mV
0.341
0.337
3086 G30
CDC Amplifier Gain
0.343
0.339
0.325
392
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G29
104
CDC Amplifier Gain
0.343
408
CDC PIN REFERENCE VOLTAGE (mV)
TRACK PIN PULL-UP CURRENT (µA)
30
105
TA = 25°C, unless otherwise noted.
TJ = 125°C
5
10 15 20 25 30 35
INPUT/OUTPUT DIFFERENTIAL (V)
40
3086 G36
1.8
1.5
1.2
0.9
0.6
0.3
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G37
3086fa
For more information www.linear.com/LT3086
9
LT3086
Typical Performance Characteristics
Reverse-Output Current
Reverse-Output Current
0.3
SET
0.1
OUT, RPWRGD
0
4
8
12 16 20 24
OUTPUT VOLTAGE (V)
28
VIN = 0V
VSHDN = 0V
60 V
OUT = 5V
RSET = 92k
50 RPWRGD = 82k
40
OUT
30
SET
20
10
RPWRGD
Input Ripple Rejection
VOUT = 5V
40
30
RIPPLE REJECTION (dB)
RIPPLE REJECTION (dB)
COUT = 22µF
10
70
60
50
100
100
50
VOUT = 5V
40
30
RIPPLE REJECTION (dB)
RIPPLE REJECTION (dB)
80
60
CSET = 0
30
100
VOUT = 0.4V
VOUT = 1V
COUT = 22µF
40
Ripple Rejection vs Temperature
70
12 16 20 24 28
OUTPUT VOLTAGE (V)
10M
30
CSET = 10nF
COUT = 22µF
CSET = 0
50
40
30
5V, 2.1A Ripple Rejection
vs VIN – VOUT
5V, 1A Ripple Rejection
vs VIN – VOUT
60
40
36
COUT = 10µF
10 VTEMP = 0.25V
VIN = 5.5V + 50mVRMS RIPPLE
0
10
100
1k
10k 100k
1M
10M
FREQUENCY (Hz)
3086 G42a
3086 G42
50mVRMS RIPPLE ON VIN
90 IL = 2.1A
COUT = 10µF
80 C
SET = 10nF
RIPPLE AT f = 10kHz
70 VTEMP = 0.25V
50
32
20
COUT = 10µF
1M
60
RIPPLE AT f = 100kHz
RIPPLE AT f = 1MHz
100
50mVRMS RIPPLE ON VIN
90 COUT = 10µF
CSET = 10nF
80 V
TEMP = 0.25V
70
RIPPLE AT f = 10kHz
60
50
40
30
20
20
10
10
10
10
8
70
20
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G43
IL = 2.1A, CSET = 0, VTEMP = 0.25V,
VIN = 1.9V + 0.5VP-P RIPPLE (FOR VOUT = 0.4V, 1V)
VIN = 5.9V + 0.5VP-P RIPPLE (FOR VOUT = 5V)
RIPPLE AT f = 120Hz
4
80
10 VTEMP = 0.25V
VIN = 5.7V + 50mVRMS RIPPLE
0
10
100
1k
10k 100k
FREQUENCY (Hz)
1k
10k 100k
1M
10M
FREQUENCY (Hz)
3086 G41
IL = 2.1A, CSET = 0, VTEMP = 0.25V,
VIN = 1.6V + 50mVRMS RIPPLE (FOR VOUT = 0.4V)
VIN = 5.7V + 50mVRMS RIPPLE (FOR VOUT = 5V)
90
90
CSET = 10nF
20
COUT = 10µF
10
0
5V, 1A Input Ripple Rejection
RIPPLE REJECTION (dB)
90
80
20
5
100
RIPPLE REJECTION (dB)
VOUT = 0.4V
50
10
5V, 2.1A Input Ripple Rejection
80
60
15
3086 G40
100
70
20
3086 G39
100
90
VIN > VOUT
VSET = 500mV
25 CURRENT FLOWS THROUGH
OUT PIN TO GND
0
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
32
3086 G38
0
OUTPUT OVERSHOOT PULL-DOWN (mA)
REVERSE OUTPUT CURRENT (µA)
REVERSE OUTPUT CURRENT (mA)
TJ = 25°C
VIN = 0V
0.5 VOUT = VSET = VRPWRGD
CURRENT FLOWS THROUGH
PINS TO GROUND
0.4
0
Overshoot Pull-Down Current
30
70
0.6
0.2
TA = 25°C, unless otherwise noted.
0
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT-TO-OUTPUT DIFFERENTIAL (V)
3086 G44
RIPPLE AT f = 1MHz
RIPPLE AT f = 100kHz
0
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
3086 G44a
3086fa
For more information www.linear.com/LT3086
LT3086
Typical Performance Characteristics
0.6
IL = 1mA TO 2.1A
0.4
0.2
IL = 1mA TO 1.5A
0
–0.2
–0.4
–0.6
–0.8
–1.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
80
VIN = VOUT(NOMINAL) + 0.55V
70
60
50
40
IL = 1mA TO 2.1A
30
20
10
IL = 1mA TO 1.5A
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G46
3086 G45
0
1.8
–10
1.6
MINIMUM INPUT VOLTAGE (V)
DD-PAK/TO-220
–20
DFN/TSSOP
–40
–50
–60
–70
VIN = 1.55V TO 40V
IL = 1mA
0.1
CSET = 100nF
CSET = 10nF
0.01
10
100
IL = 100mA
1.2
1.0
0.8
0.6
0.4
VIN = 1.55V TO 40V
0.9 IL = 1mA
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G046a
CSET = 1nF
1k
10k
FREQUENCY (Hz)
100k
3086 G49
10
Output Noise Spectral Density,
CSET = 0
IL = 2.1A
COUT = 10µF
VTEMP = 0.25V
VOUT = 3.3V
VOUT = 5V
1
VOUT = 2.5V
VOUT = 1.2V
0.1
VOUT = 0.4V
0.01
10
100
1k
10k
FREQUENCY (Hz)
100k
3086 G47
350
CSET = 100pF
1
1.4
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
Output Noise Spectral Density
vs CSET
VOUT = 5V
IL = 2.1A
COUT = 10µF
VTEMP = 0.25V
IL = 2.1A
0.2
–80
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 G046b
10
1.0
Minimum Input Voltage
OUTPUT NOISE VOLTAGE (µVRMS)
OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz)
CHANGE IN SET PIN REFERENCE CURRENT (nA)
Reference Current Line
Regulation
–30
CHANGE IN SET PIN REFERENCE VOLTAGE (mV)
VIN = VOUT(NOMINAL) + 0.55V
OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz)
0.8
Reference Voltage Line
Regulation
3086 G48
RMS Output Noise vs Load
Current, CSET = 0
COUT = 10µF
COUT = 22µF
300 f = 10Hz TO 100kHz
VTEMP = 0.25V
250
70
VOUT = 5V
200
VOUT = 3.3V
150
VOUT = 2.5V
100
VOUT = 1.2V
50
0
100µ
VOUT = 0.4V
1m
10m
100m
LOAD CURRENT (A)
1
10
3086 G50
OUTPUT NOISE VOLTAGE (µVRMS)
1.0
Reference Current Load
Regulation
CHANGE IN SET PIN REFERENCE CURRENT (nA)
CHANGE IN SET PIN REFERENCE VOLTAGE (mV)
Reference Voltage Load
Regulation
RMS Output Noise vs Load
Current, CSET = 10nF
COUT = 10µF
COUT = 22µF
60 f = 10Hz TO 100kHz
VTEMP = 0.25V
50
VOUT = 5V
40
30
VOUT = 0.4V
20
10
0
100µ
1m
10m
100m
LOAD CURRENT (A)
1
10
3086 G51
3086fa
For more information www.linear.com/LT3086
11
LT3086
Typical Performance Characteristics
RMS Output Noise vs Load
Current
f = 10Hz TO 100kHz
VOUT = 0.4V
50 VTEMP = 0.25V
250
COUT = 22µF
40
30
20
COUT = 100µF
COUT = 47µF
10
RMS Output Noise vs
Feedforward Capacitor (CSET)
f = 10Hz TO 100kHz
IL = 2.1A
COUT = 10µF
VTEMP = 0.25V
225
COUT = 10µF
OUTPUT NOISE VOLTAGE (µVRMS)
OUTPUT NOISE VOLTAGE (µVRMS)
60
TA = 25°C, unless otherwise noted.
200
175
VOUT = 5V
150
VOUT = 3.3V
125
100
75
VOUT = 2.5V
50
VOUT = 1.2V
25
0
100µ
1m
10m
100m
LOAD CURRENT (A)
1
VOUT = 0.4V
0
10p
10
100p
1n
10n
FEEDFORWARD CAPACITOR CSET (F)
3086 G52
Output Voltage Noise
3086 G53
Load Transient Response
Load Transient Response
CSET = 0
50
0
–50
CSET = 10nF
–100
–150
3086 G54
LOAD
CURRENT (A)
VOUT = 5V
RSET = 92k
CSET = 10nF
COUT = 10µF
IL = 2.1A
f = 10Hz TO 100kHz
VIN = 5.5V
150 VOUT = 5V
100 COUT = 10µF
LOAD
CURRENT (A)
TIME 1ms/DIV
300
OUTPUT VOLTAGE
DEVIATION (mV)
OUTPUT VOLTAGE
DEVIATION (mV)
200
VOUT
100µV/DIV
3
∆IL = 500mA TO 1.5A
2
1
0
0
100n
20
40
60 80 100 120 140 160
TIME (µs)
VIN = 5.5V
200 VOUT = 5V
CSET = 10nF
100
COUT = 10µF CERAMIC
0
–100
COUT = 10µF CERAMIC +
100µF TANTALUM
–200
3
∆IL = 210mA TO 2.1A
2
1
0
0
40
80
120 160 200 240 280 320
TIME (µs)
3086 G55
Line Transient Response
Start-Up Response
0
–5
∆VIN = 5.55V TO 12V
12
8
6
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
TIME (ms)
3086 G57
12
RL = 5kΩ (IL = 1mA)
3
2
1
1.5
1.0
Start-Up Time vs CSET
IL = 1mA
SETTLING TO 1%
VOUT = 5V
RL = 2.38Ω (IL = 2.1A)
0
10
4
COUT = 10µF
5 RSET = 92k
CSET = 0
4
100
START-UP TIME (ms)
IL = 2.1A
10 VOUT = 5V
COUT = 10µF
5
SHDN PIN
VOLTAGE (V)
INPUT VOLTAGE (V)
6
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE
DEVIATION (mV)
15
–10
3086 G56
10
VOUT = 3.3V
1
VOUT = 1.2V
0.1
VOUT = 2.5V
0.5
0
0
20
40
60 80 90
TIME (µs)
100 120 140
3086 G58
0.01
10p
100p
1n
10n
100n
FEEDFORWARD CAPACITOR, CSET (F)
3086 G59
3086fa
For more information www.linear.com/LT3086
LT3086
Pin Functions
(DFN/TSSOP/DD-Pak/TO-220)
GND (Pins 1, 16, Exposed Pad Pin 17/Pins 1, 8, 9, 16,
Exposed Pad Pin 17/Pin 4/Pin 4): Ground. The exposed
pad of the DFN and TSSOP packages as well as the Tab
of the DD-Pak and TO-220 packages is an electrical connection to GND. To ensure proper electrical and thermal
performance, tie the exposed pad or tab directly to the
remaining GND pins of the relevant package and the PCB
ground. GND pin current is typically 1.2mA at zero load
and increases to about 44mA at full load.
ILIM (Pin 2/Pin 2/Pin 1/Pin 1): External Current Limit
Programming. This pin externally programs current limit
if connected to IMON and a resistor to GND. Current limit
activates if the voltage at ILIM equals 0.8V. Current limit
equals: 1000 • (0.8V/RMON). An internal clamp typically
limits the ILIM voltage to 1V. If external current limit is set to
less than 1A, connect a series 1k-10nF network in parallel
with the RMON resistor for stability. Internal current limit
foldback overrides externally programmed current limit if
VIN – VOUT differential voltage is excessive. If external current limit programming is not used, then ground this pin.
IMON (Pin 3/Pin 2/Pin 1/Pin 1): Output Current Monitor.
This pin sources a current equal to 1/1000 of output load
current. Connecting a resistor from IMON to GND programs
a load current dependent voltage for monitoring by an
ADC. If IMON connects to ILIM, current limit is externally
programmable.
CDC (Pin 4/Pin 3/NA/NA): Cable Drop Compensation.
Connecting a single resistor (RCDC) between the CDC and
SET pins provides programmable cable drop compensation that cancels output voltage errors caused by resistive
connections to the load. A resistor (RMON) from IMON to
GND is also required to enable Cable Drop Compensation.
Choose RMON first based on required current limit.
RMON = 0.8V • 1000/ILIM
Calculate the value of RCDC with this formula:
RCDC = (RMON • RSET)/(3000 • RWIRE)
where RWIRE is the total cable or wire resistance to and
from the load. From a practical application standpoint,
LTC recommends limiting cable drop compensation to
20% of VOUT for applications needing good regulation.
The limiting factor is variations in wire temperature as
copper wire resistance changes about 19% for a 50°C
temperature change. If output regulation requirements
are loose (e.g., when using a secondary regulator), cable
drop compensation of up to 50% may be used.
RPWRGD (Pin 5/Pin 4/NA/NA): Power Good Threshold
Voltage Programming. This pin is the input to the power
good comparator. Connecting a resistor between OUT and
RPWRGD programs an adjustable power good threshold
voltage. The threshold voltage is 0.4V on the RPWRGD pin,
and a 50µA current source is connected from RPWRGD
to GND. If the voltage at RPWRGD is less than 0.4V, the
PWRGD flag asserts and pulls low. If the voltage at RPWRGD is greater than 0.4V, the PWRGD flag de-asserts
and becomes high impedance. For most applications,
PWRGD is pulled high with a pull-up resistor. Calculate
the value of RPWRGD with this formula:
RPWRGD = (X • VOUT(NOMINAL) – 0.4V)/50µA
where X is normally in the 85% to 95% range.
A 17µs deglitching filter suppresses false tripping of the
PWRGD flag at the rising edge of PWRGD with instant
reset. Hysteresis at the RPWRGD pin is typically 0.6% on
the 0.4V threshold and the 50µA current source.
SET (Pin 6/Pin 5/Pin 2/Pin 2): Output Voltage Programming. This pin is the error amplifier’s inverting terminal. It
regulates to 0.4V and a 50µA current source is connected
from SET to GND. Connecting a single resistor from OUT
to SET programs output voltage. Calculate the value of
the required resistor from the formula:
RSET = (VOUT – 0.4V)/50µA
Connecting a capacitor in parallel with RSET provides output
voltage soft-start capability, improves transient response
and decreases output voltage noise.
The LT3086 error amplifier design is configured so that
the regulator always operates in unity-gain.
OUT (Pins 7, 8/Pins 6, 7/Pin 3/Pin 3): Output. These
pin(s) supply power to the load. Connect all OUT pins
together on the DHD and FE packages for proper operation.
Stability requirements demand a minimum 10µF ceramic
output capacitor with an ESR less than 100mΩ to prevent
oscillations. Large load transients require larger output
capacitance to limit peak voltage transients. Permissible
3086fa
For more information www.linear.com/LT3086
13
LT3086
Pin Functions
(DFN/TSSOP/DD-Pak/TO-220)
output voltage range is 0.4V to 32V. The LT3086 requires
a 1mA minimum load current to ensure proper regulation and stability.
IN (Pins 10, 11/Pins 10, 11/Pin 5/Pin 5): Input. These
pin(s) supply power to the device. Connect all IN pins
together on the DHD and FE packages for proper operation. The LT3086 requires a local IN bypass capacitor if
it is located more than a few inches from the main input
filter capacitor. In general, battery output impedance rises
with frequency, so adding a bypass capacitor in battery
powered circuits is advisable. A 10µF minimum input
capacitor generally suffices. The IN pin(s) withstand a
reverse voltage of 45V. The device limits current flow and
no negative voltage appears at OUT. The device protects
itself and the load against batteries that are plugged in
backwards.
pin also incorporates the ability to program a thermal
limit temperature lower than the internal typical thermal
shutdown temperature of 165°C. Tying a resistor from
TEMP to GND programs the thermal limit temperature
with a 100µA trip point. Calculate the value of the resistor
from the formula:
10mV 

 TSHDN •

°C 
R TEMP =
100µA
where TSHDN is the desired die thermal limit temperature.
There are several degrees of hysteresis in the thermal
shutdown that cycles the regulator output on and off. Limit
the capacitance on the TEMP pin to less than 100pF. To
prevent saturation in the TEMP output device, ensure that
VIN is higher than VTEMP by 250mV.
SHDN (Pin 12/Pin 12/Pin 6/Pin 6): Shutdown/UVLO.
Pulling the SHDN pin typically below 1V puts the LT3086
into a low power state and turns the output off. Quiescent
current in shutdown is typically less than 1µA. The SHDN
pin turn-on threshold is typically 1.22V. This pin may either
be used as a shutdown function or as an undervoltage
lockout function. If using this pin as an undervoltage
lockout function, use a resistor divider between IN and
GND with the tap point tied to SHDN. If using the pin as
a shutdown function, drive the pin with either logic or an
open-collector/drain with a pull-up resistor. The resistor
supplies the pull-up current to the open-collector/drain
logic, normally several microamperes, and the SHDN pin
current, typically less than 10µA at 6V. If unused, connect
the SHDN pin to IN.
TRACK (Pin 14/Pin 14/NA/NA): Track pin for paralleling.
The TRACK pin allows multiple LT3086s to be paralleled
in a master/slave(s) configuration for higher output current applications. This also allows heat to be spread out
on the PCB. This circuit technique does not require ballast
resistors and does not degrade load regulation. Tying the
TRACK pin of the slave device(s) to the IMON/ILIM pins
of the master device enables this function. If the TRACK
function is unused, TRACK is in a default clamped high
state. A TRACK pin voltage below 1.2V on slave device (s)
shuts off the internal 50µA reference current at SET such
that only the 50µA reference current of the master device
is active. All SET pins must be tied together in a master/
slave configuration.
TEMP (Pin 13/Pin 13/Pin 7/Pin 7): Die Junction Temperature. This pin outputs a voltage indicating the LT3086
average die junction temperature. At 25°C, this pin typically
outputs 250mV. The TEMP pin slope equals 10mV/°C so
that at 125°C, this pin typically outputs 1.25V. This pin
does not read temperatures less than 0°C. The TEMP pin
is not meant to be an accurate temperature sensor, but
is useful for debug, monitoring and calculating thermal
resistance of the package mounted to the PCB. The TEMP
PWRGD (Pin 15/Pin 15/NA/NA): Power Good Flag. The
PWRGD pin is an open-collector logic pin connected to
the output of the power good comparator. PWRGD asserts
low if the RPWRGD pin is less than 400mV. The maximum
low output level of 200mV over temperature is defined for
200μA of sink current. If RPWRGD is greater than 400mV,
the PWRGD pin de-asserts and becomes high impedance.
The PWRGD pin may be pulled to 36V without damaging
any internal circuitry regardless of the input voltage.
14
3086fa
For more information www.linear.com/LT3086
LT3086
Block Diagram
0.05Ω
IN
QPOWER
50Ω
OUT
120mV
+
300mV
–
+
+
–
CABLE
DROP COMP
INTERNAL
ILIMIT
CURRENT
MONITOR
IOUT
IMON =
1000
CDC
–
40k
120k
IMON
SET
–
300mV
+
EXTERNAL
ILIMIT
125k
ILIM
ERROR
AMP
–
+
75k
900mV
1.3V
900mV
100k
100k
–
13µA
TRACK
gm = 8µ
TRACK
+
EN
25k
–
EN
TRACK
ENABLE
1.2V
50µA
+
PWRGD
VREF
400mV
+
17µs DELAY
RPWRGD RISING EDGE
RPWRGD
–
IN
50µA
1.22V
+
+
TEMP
100µA
SHUTDOWN
CONTROL
–
–
TEMP
VTEMP
10mV/°C
25°C = 250mV
SHDN
GND
3086 BD
3086fa
For more information www.linear.com/LT3086
15
LT3086
Applications Information
The LT3086 is a multifunction, low dropout, low noise,
linear regulator with shutdown, and adjustable power
good. The device supplies 2.1A with a typical dropout
voltage of 330mV and operates over a wide 1.4V to 40V
input supply range.
The operating quiescent current is 1.2mA and drops to less
than 1µA in shutdown. The LT3086 regulator optimizes
stability and transient response with a minimum low ESR
10µF ceramic output capacitor. A single resistor sets the
output voltage from 0.4V to 32V. Similarly, a single resistor sets the power good threshold. The regulator typically
provides 0.1% line regulation and 0.1% load regulation.
The LT3086 has convenient programmable diagnostic
features. An output current monitor, that is typically
1/1000 of the output current, can set the current limit
lower than the typical 2.4A internal limit. A temperature
monitor, that is typically 10mV/°C where 250mV = 25°C,
can set the thermal limit lower than the typical 165°C
internal thermal limit.
For applications where the voltage error at the load is
caused by the resistance in the connections between the
LT3086 and the load, programmable cable drop compensation cancels the error with a single resistor. Multiple
LT3086 regulators can be paralleled for higher load currents and heat spreading without the need for external
ballast resistors.
During load transients where the output overshoots
(regulated output voltages of 0.8V or higher), an internal
pull-down current activates pulling about 15mA from the
OUT pin to ground. The pull-down current is disabled when
the output is at or below regulation. The regulator and
the output overshoot pull-down turn off when the output
voltage is pulled higher than the input by typically 225mV.
Curves of OUT Over IN Shutdown Threshold appear in the
Typical Performance Characteristics section.
Internal protection circuitry includes reverse-battery protection, reverse-output protection, reverse-current protection, current limit with foldback and thermal shutdown.
IN
OUT
VOUT
LT3086
VIN
SHDN
RSET
SET
VOUT =ISET •RSET + 0.4V
IMON
ILIM
VIMON
RMON
ISET = 50µA
VOUT – 0.4V
50µA
OUTPUT RANGE = 0.4V TO 32V
RSET =
GND
3086 F01
Figure 1. Programming Output Voltage
Table 1. Output Voltage RSET Values
VOUT (V)
IDEAL
RSET (Ω)
SINGLE 1%
DUAL 1%
VOUT ERROR FOR
SINGLE 1%
1
12k
12.1k
11.8k + 200
0.5%
1.2
16k
16.2k
15.8k + 200
0.8%
1.5
22k
22.1k
21.5k + 511
0.3%
1.8
28k
28k
N/A
0%
2
32k
32.4
31.6k + 383
1.0%
2.5
42k
42.2k
41.2k + 825
0.4%
3.3
58k
57.6k
57.6k + 383
–0.6%
5
92k
90.9k
90.9k + 1.1k
–1.1%
12
232k
232k
N/A
0%
Table 1 shows the nearest 1% resistor values for some
common output voltages, along with the output error
caused by not using the ideal resistance value. These
errors can be as high as 1% because of the 2% spacing
between standard 1% resistors. If tighter output tolerance is required, consider using more accurate resistors.
Alternatively, the resistance of RSET can be fine-tuned by
adding a low value 1% resistor in series, see Table 1 dual
1% column.
Programming Power Good
Programming Output Voltage
The LT3086 has an output voltage range of 0.4 to 32V.
The output voltage is programmed with a single resistor,
RSET, connected from OUT to the SET pin, as shown in
Figure 1. The SET pin has an internal 50µA current source
16
to ground that generates a voltage drop across RSET. The
device servos the output to maintain the SET pin voltage
at 0.4V referenced to ground. Calculate the output voltage
using the formula in Figure 1. Curves of SET Pin Reference
Voltage and Current vs Temperature appear in the Typical
Performance Characteristics section.
The adjustable power good threshold is programmed
with a single resistor, RPGSET, similar to how the output
voltage is programmed by RSET. Similar to the SET pin,
RPWRGD determines the power good threshold with the
For more information www.linear.com/LT3086
3086fa
LT3086
Applications Information
combination of a 0.4V reference voltage and a precision
50µA pull-down current. The power good signal pulls high
if the voltage on RPWRGD increases above 0.4V. Built-in
hysteresis of typically 0.6% exist for both the 0.4V voltage threshold and the 50µA current source. Connecting
a resistor between the RPWRGD and PWRGD pins can
increase the power good hysteresis. See the Application
circuits for an example.
IN
VIN
OUT
LT3086
SHDN
VOUT
RSET
SET
VLOGIC
OR VOUT
RPGSET
VIMON
RMON
IMON RPWRGD
ILIM PWRGD
GND
3086 F02
RPGSET =
x • VOUT(NOMINAL) – 0.4V
50µA
WHERE 85% ≤ x ≤ 95% TYPICALLY
RPGD
VPWRGD
CPGSET
(OPTIONAL)
Figure 2. Programming Power Good
The PWRGD pin is the power good open-collector logic
output. An internal delay of typically 17µs exists only for
the rising edge (when the regulator output voltage rises
above the power good threshold) to reject noise or chatter
during startup. If the power good function is not needed,
leave the RPWRGD and PWRGD pins floating.
The power good threshold is typically programmed to 85%
to 95% of the regulated output voltage. Due to variations in
regulator parameters and resistor variations, it is not practical to set the power good threshold greater than 95% of the
output voltage. Account for load transients where the output
voltage droops momentarily before recovering. If increasing
output capacitance to reduce output voltage undershoot or
if setting the power good threshold lower is not possible, a
capacitor, CPGSET, from RPWRGD to ground can filter and delay
the output signal. This allows for a configurable deglitching
period before the power good threshold trips. For example,
consider an application with a nominal 1V output using 10µF
of output capacitance and the power good threshold set
for 90% of VOUT(NOMINAL). A 1.5A output load current step
momentarily undershoots VOUT below the 90% threshold
for more than 4µs, thus triggering the PWRGD pin to pull
low. Using a CPGSET of greater than 270pF deglitches the
power good comparator and prevents the PWRGD pin from
pulling low for undershoot events less than 4µs in duration.
For applications using cable drop compensation and requiring a power good signal, calculate the value of RPGSET
based on the voltage at the load rather than the LT3086’s
output voltage. In order for the power good threshold to be
independent of the cable drop compensation’s modulation
of the LT3086’s output voltage as a function of load current, connect a resistor between CDC and RPWRGD with the
same value as RCDC, the resistor between CDC and SET.
This technique avoids connecting the RPGSET resistor to
the load voltage through a long trace/wire and eliminates
potential stray signal coupling into the RPWRGD pin. See
the front page Typical Application circuit as an example.
Output Voltage Noise and Transient Response
The LT3086 regulator provides low output voltage noise
over a 10Hz to 100kHz bandwidth while operating at full
load. Output voltage noise is approximately 65nV/√Hz
over this frequency bandwidth at the unity gain output
voltage of 0.4V at 2.1A.
To lower output voltage noise for higher output voltages,
include a feedforward capacitor, CSET, from OUT to the
SET pin, as shown in Figure 3. A good quality, low leakage
capacitor is recommended. This capacitor bypasses the
voltage setting resistor, RSET, providing a low frequency
noise pole. With the use of 10nF for CSET, output voltage
noise decreases from 280µVRMS to 40µVRMS at 2.1A when
the output voltage is set to 5V.
IN
VIN
VIMON
RMON
OUT
LT3086
SHDN
IMON
ILIM
VOUT
RSET
CSET
COUT
SET
GND
3086 F03
Figure 3. Feedforward Capacitor for Improved
Transient Response
Higher values of output voltage noise are often measured
if care is not exercised with regard to circuit layout and
testing. Crosstalk from nearby active signal traces may
induce unwanted noise onto the LT3086’s output. Power
supply ripple rejection must also be considered. The
LT3086 regulator does not have unlimited power supply
rejection and will pass a small portion of the input noise
to the output.
Using a feedforward capacitor, CSET, has the added benefit
of improving transient response for output voltages greater
than 0.4V. With no feedforward capacitor, the settling time
For more information www.linear.com/LT3086
3086fa
17
LT3086
Applications Information
and output voltage transients increase as the output voltage
is set above 0.4V. See Figure 4 and Transient Response
curves in the Typical Performance Characteristics section.
OUTPUT VOLTAGE
DEVIATION (mV)
50
0
LOAD
CURRENT (A)
RMON
CSET = 1nF
–200
CSET = 0
3
VIN = 5.5V
VOUT = 5V
COUT = 10µF
∆IL = 210mA TO 2.1A
2
1
0
0
10
20
30 40 50
TIME (µs)
60
70
80
3086 F04
Figure 4. Transient Response vs Feedforward Capacitor
Start-up time is affected by the use of a CSET feedforward
capacitor. Start-up time is directly proportional to the size
of the feedforward capacitor and output voltage. Settling
time to 1% is approximately:
tSETTLE =
4.2 • VOUT •CSET
50µA
See the Start-Up Time vs CSET curve in the Typical Performance Characteristics section. If the LT3086 is configured
for cable drop compensation, LTC does not recommend
using a feedforward capacitor because CSET filters the
CDC correction signal and transient response to load
current changes degrades.
Output Current Monitor and External Current Limit
Current out of the IMON pin is typically equal to 1/1000
of the regulator’s output current. The output current
monitor maintains accuracy across the full input voltage
range, even during dropout. A resistor, RMON, placed from
IMON to ground, sets the voltage scale factor for use with
analog-to-digital converters, as shown in Figure 5. For
example, with 442Ω for RMON, VIMON is set for 0.663V
when IOUT = 1.5A.
External current limit activates if the voltage on the ILIM
pin exceeds the typical 0.8V threshold. Tying the IMON and
ILIM pins together allows the user to program a desired
current limit based on the output current. An internal cur-
VOUT
RSET
SET
IOUT
1000
VIMON =IMON •RMON
IMON =
IMON/ILIM
GND
3086 F05
–100
–250
18
VIMON
CSET = 100pF
–150
OUT
LT3086
SHDN
TO ADC
CSET = 10nF
–50
IN
VIN
ILIMIT = 1000 •
0.8V
RMON
Figure 5. Output Current Monitor and External Current Limit
rent limit, typically 2.4A, is always active and limits output
current even if the ILIM pin is grounded. In addition, internal current limit foldback overrides external current limit
if the VIN – VOUT differential voltage becomes excessive.
Note that the output current monitor represents not just
the load current, but the current into the output capacitor
as well. During startup and large load transients, the output
current monitor indicates the current required to charge
the output capacitor in addition to the load current. To
prevent external current limit from engaging prematurely,
set the external current limit above the maximum load
current to allow the output capacitor to recover without
being current limited.
For external current limits set for less than 1A, connect a
series 1k-10nF RC network from ILIM to ground to ensure
current limit loop stability. Adding an RC network from ILIM
to ground also delays the current monitor signal, allowing
output currents higher than the external current limit for a
limited duration. This is useful for applications with large
output capacitance that would otherwise trigger external
current limit during startup and large load transients,
slowing output voltage recovery. To guarantee external
current limit stability, ensure that the RC network from
ILIM to GND has a capacitor value equal to or greater than
10nF and the resistor value is between 0.01• C–0.6 and
1k. C is the capacitor value in units of farads. LTC does
not recommend an RC network other than the 1k-10nF
combination if using the cable drop compensation and
paralleling functions.
To configure the output current monitor and external current limit correctly, decide on the necessary current limit
and full-scale monitor output voltage. Voltage is limited to
0.8V if IMON is tied to ILIM. External current limit is typically
set 10% to 20% above maximum load current to allow for
3086fa
For more information www.linear.com/LT3086
LT3086
Applications Information
large transient events and ILIM threshold variations. For
example, if the maximum load current is 1.5A and both
IMON and ILIM pins are tied together, an RMON scaling
resistor of 442Ω yields an external current limit of 1.8A.
If higher output current monitor voltages are needed, the
DFN package offers the ability to separate the IMON and
ILIM pins with a resistor, as shown in Figure 6. To prevent
saturation in the IMON output device, choose RMON so that
VIMON is at least 0.6V less than VIN. If external current is
not needed, ground the ILIM pin.
Output current monitor accuracy for very low output currents is limited by the offset in the current monitor amplifier
and parasitic current paths. The equivalent circuit of the
parasitic current paths are shown in Figure 7. With zero
output load current, the current into RMON is typically
11µA when the IMON and ILIM pins are tied together. As
a result, load currents between 0mA and 11mA typically
cannot be measured. See Current Monitor Offset curves
in the Typical Performance Characteristics section.
Load Regulation and Cable Drop Compensation
high current applications, small voltage drops appear due
to the resistances of PCB traces or wires between the
regulator and the load. These drops may be eliminated
by connecting RSET directly to the output at the load as
shown in Figure 8. Note that the voltage drop across ROUT
and RRTN add to the dropout voltage of the regulator. The
voltage drop across RGND should also be minimized to
reduce output voltage error due to ground pin current.
See GND Pin Current curves in the Typical Performance
Characteristics section.
The LT3086 has cable drop compensation (CDC) functionality that allows delivery of well regulated voltage
to remote loads using only two wires of known fixed
resistance. Compensation is user programmed by connecting a resistor, RCDC, between the SET and CDC pins,
as shown in Figure 9.
At zero load current, the CDC pin typically regulates to
the same voltage as the SET pin. The voltage decreases
at a rate equal to 1/3 of the change in IMON voltage. For
example, if VIMON increases from 0 to 0.6V, VCDC decreases
Output load regulation for the LT3086 is typically 0.1%.
Optimal regulation is obtained when the RSET feedback
resistor is connected to the OUT pin of the regulator. In
IN
LT3086
SHDN
IN
OUT
LT3086
SHDN
TO ADC
VIMON
ROPT
(DFN PACKAGE ONLY)
RLIM
RMON
SET
ILIMIT = 1000 •
0.8V
RLIM
RMON
ILIM
67k
3086 F08
3086 F06
IN
IMON
300mV
IMON NOT TIED TO ILIM
43k
480mV
ILIM
600mV
RMON
SHDN
IMON
ILIM
RMON
LLINE1
RSET
SET
RCDC
VIN
IOUT/1000
RLINE1
OUT
LT3086
LT3086
IN
IOUT/1000
120k
RGND
Figure 8. Kelvin Sense Connection
GND
LT3086
IMON
RSET
RRTN
Figure 6. Separate IMON and ILIM (DFN Package Only)
IN
GND
RMON = RLIM +ROPT
IMON
ILIM
IMON
ILIM
VOUT
RSET
SET
ROUT
LOAD
VIN
VIN
OUT
CDC
GND
CLOAD
(OPTIONAL)
LOAD
COUT
RESR
(OPTIONAL)
RLINE2
LLINE2
3086 F09
IMON TIED TO ILIM
3086 F07
Figure 7. Equivalent Circuits of IMON and ILIM
RCDC =
RMON •RSET
3000 •R WIRE
R WIRE = RLINE1 +RLINE2
Figure 9. Cable Drop Compensation
For more information www.linear.com/LT3086
3086fa
19
LT3086
Applications Information
by 0.2V. As a result, the current that flows through RCDC
is proportional to load current which increases the voltage
across RSET, effectively increasing output voltage. RCDC is
selected using the following equation so that the voltage
at the OUT pin increases to cancel the voltage drop in the
cables connected to the load.
RCDC =
RMON •RSET
3000 •R WIRE
where RWIRE is the total resistance of the supply and return
cabling connecting the LT3086 to the load.
Figure 10 shows the transient response with cable drop
compensation. With compensation, the output voltage at
the load remains nearly constant. Note that the transient
voltage droop in output voltage is about the same as the
voltage droop with no compensation, but with the output
voltage returning to the correct compensated voltage.
5.8
OUTPUT VOLTAGE (V)
5.6
VOUT WITH CDC
5.2
5.0
VLOAD WITH CDC
4.8
VIN = 6V
VLOAD WITHOUT CDC RMON = 357Ω
RWIRE = 0.24Ω
RCDC = 46.4k
RSET = 92k
COUT = 10µF
∆ILOAD = 0.5A TO 1.5A
CLOAD = 0
4.6
LOAD
CURRENT (A)
4.4
4.2
2
1
0
80 160 240 320 400 480 560 640 720 800
TIME (µs)
3086 F10
Figure 10. Transient Response with Cable Drop Compensation
If long cables are used, an additional supply bypass
capacitor, CLOAD, should be added directly to the load
to handle large load transient conditions. COUT must still
directly connect to the OUT pin to ensure stable operation
of the LT3086, minimizing output capacitor ESR and ESL.
Long cables have inductance where a resonance forms
between the wire inductance, LWIRE and CLOAD. Damping
is accomplished by adding series resistance, RESR, to
CLOAD. The value of RESR is approximately:
RESR = 2 •
Noise from the current monitor output affects noise seen
at the output. Filtering the current monitor output with an
RC network from ILIM to ground is effective at reducing
this noise source, especially at light loads. Consult the
Output Current Monitor and External Current Limit section
for more information
Paralleling Multiple Regulators
5.4
0
There are limits to the amount of voltage drop that can
be compensated using cable drop compensation. Using
cable drop compensation subjects load regulation to the
variability of the current monitor voltage output and the
cabling resistance. LTC recommends limiting cable drop
compensation to 20% of VOUT for applications needing
good regulation. The limiting factor is variations in wire
temperature as copper wire resistance changes about
19% for a 50°C temperature change. If output regulation
requirements are loose (e.g., when using a secondary
regulator), cable drop compensation of up to 50% may
be used.
The LT3086 has been specifically designed to make paralleling multiple regulators together easy. Paralleling enables
applications to increase total output current and to spread
heat dissipated by the regulator over a wider area on the
PCB. The parallel scheme is based on a master/slave
principle, where one LT3086 is designated as master,
and the other regulators act as slaves with active sharing
of total load current, as shown in Figure 11. The slave’s
internal current tracking amplifier compares the current
monitor output from the master with the current monitor
output seen at the slave’s ILIM pin, and servos the slave’s
output current to match the master’s.
VIN
IN SHDN OUT
VOUT
LT3086
MASTER
SET
OUT SHDN IN
RSET
VTRACK = VILIM(MASTER)
L WIRE
CLOAD
GND
IMON
ILIM
RMON
RMON
LT3086
SLAVE(S)
SET
TRACK
IMON
ILIM
GND
3086 F011
Figure 11. Master/Slave(s) Configuration for Paralleling
20
3086fa
For more information www.linear.com/LT3086
LT3086
Applications Information
The master LT3086 is connected exactly the same as a
single regulator where its output current monitor voltage
seen at its ILIM pin is used as the common current tracking
signal. The slave devices connect this signal to their TRACK
pins to make their output current equal to the master’s.
The TRACK pin has an internal pull-up current that is
typically 15µA at 0.75V. When the TRACK pin is unused,
the pin is pulled up and clamped at 1.25V, disabling the
current tracking amplifier. When the TRACK pin is connected to the master current tracking signal, the TRACK
pin voltage is pulled below the 1.2V threshold, enabling the
current tracking amplifier and disabling the slave’s 50µA
reference current, ISET. Disabling the reference current
ensures that the master is the only device controlling the
output voltage. Set the maximum master current tracking
signal to less than 0.8V to prevent external current limit
from triggering prematurely. To prevent the slave current
tracking amplifier from ever being disabled, the slave
TRACK pin must be tied to the master ILIM pin. The master
ILIM pin has an internal 1V clamp that is below the slave
1.2V current tracking amplifier enable threshold.
When multiple slaves are used, a smaller master RMON
resistor should be used to compensate for the pull-up
currents from all the TRACK pins of the slaves. For example, a master sourcing 2.1A typically has 0.697V at its
ILIM pin with an RMON resistor of 332Ω. Referring to the
TRACK pin pull-up current curve in the Typical Performance Characteristics, with 0.697V on the TRACK pin,
each slave typically adds 15µA to the master’s 2.1mA
IMON output. For an application with 5 slaves connected,
decrease RMON’s value to:
RMON =
0.697V
= 325Ω
[2.1mA + ( 5 •15µA )]
The closest 1% resistor value equals 324Ω.
All slave regulators must have their SET pins connected
to the master SET pin. The TRACK amplifier operates by
adjusting the slave internal reference voltage slightly as
a function of the difference in master and slave current
monitor voltages. This has a strong effect on the slave
output current, which forces the slave output current to
match the master.
Mismatch between master and slave internal reference
voltages and current monitor outputs, offset in the slave
TRACK amplifier and TRACK pin pull-up currents all
contribute to output current sharing error. In the case of
negative offset, a slave runs less current than the master.
At very light loads, negative offset enables the slave output
overshoot pull-down circuit, forcing the master to supply
current to keep the output voltage within regulation. As a
result, quiescent current may increase for very light loads
in the master/slave configuration.
In some applications, multiple regulators may be spaced
some distance apart to optimize heat distribution. That
makes the use of low resistance traces important to connect each regulator to the local ground system and to avoid
ground loops created by load currents. Ground currents
can be as high as 30mA at 1.5A and 50mA at 2.1A, for
each regulator. Limiting differential ground pin voltages to
less than 10mV minimizes tracking errors. Ground trace
resistance between master and slaves should be less than
10mV/30mA = 0.33Ω at 1.5A load, and 10mV/50mA =
0.2Ω for 2.1A load.
Output Capacitance
The LT3086 regulator is stable with a wide range of output
capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. Use a minimum
output capacitor of 10µF with an ESR of 0.1Ω or less to
prevent oscillations. The output load transient response is
a function of output capacitance. Larger values of output
capacitance decrease the peak deviations and provide improved transient response for larger load current changes.
For applications with large load current transients, a low
ESR ceramic capacitor in parallel with a bulk tantalum
capacitor often provides an optimally damped response.
For example, a 47µF tantalum capacitor with ESR = 0.1Ω
in parallel with the 10µF ceramic capacitor with ESR <
0.01Ω reduces output deviation by about 2:1 for large
transient loads and increases loop phase margin.
Give extra consideration to the use of ceramic capacitors.
Manufacturers make ceramic capacitors with a variety of
dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics
are specified with EIA temperature characteristic codes
of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics
3086fa
For more information www.linear.com/LT3086
21
LT3086
Applications Information
provide high C-V products in a small package at low cost,
but exhibit strong voltage and temperature coefficients, as
shown in Figures 12 and 13. When used with a 5V regulator,
a 16V 10µF Y5V capacitor can exhibit an effective value
as low as 1µF to 2µF for the DC bias voltage applied, and
over the operating temperature range. The X5R and X7R
dielectrics yield much more stable characteristics and are
more suitable for use as the output capacitor.
The X7R type works over a wider temperature range and
has better temperature stability, while the X5R is less
expensive and is available in higher values. Care still must
be exercised when using X5R and X7R capacitors; the X5R
and X7R codes only specify operating temperature range
and maximum capacitance change over temperature.
Capacitance changes due to DC bias is less with X5R and
X7R capacitors, but can still be significant enough to drop
capacitor values below appropriate levels. Capacitor DC
20
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
CHANGE IN VALUE (%)
0
X5R
–20
–40
–60
Y5V
–80
–100
0
2
4
14
8
6
10 12
DC BIAS VOLTAGE (V)
16
3086 F12
Figure 12. Ceramic Capacitor DC Bias Characteristics
40
CHANGE IN VALUE (%)
20
X5R
0
–20
–40
Y5V
–60
–80
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
–100
–50 –25
50
25
75
0
TEMPERATURE (°C)
100
125
3086 F13
Figure 13. Ceramic Capacitor Temperature Characteristics
22
bias characteristics tend to improve as component case
size increases, but expected capacitance at operating
voltage should be verified.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor, the stress is
induced by vibrations in the system or thermal transients.
The resulting voltages produced can cause appreciable
amounts of noise.
Input Capacitance
Low ESR ceramic input bypass capacitors are acceptable for
applications with short input and ground leads. However,
applications connecting a power supply to the LT3086
using long wires are prone to voltage spikes, reliability
concerns and application-specific board oscillations.
The input wire inductance found in many battery-powered
applications, combined with the low ESR ceramic capacitor,
forms a high-Q LC resonant tank circuit. In some instances
this resonant frequency beats against the output current
dependent LDO bandwidth and interferes with proper
operation. Simple circuit modifications are then required.
This behavior is not indicative of LT3086 instability, but
is a common application issue.
The self-inductance, or isolated inductance, of a wire is
directly proportional to its length. Wire diameter is not a
major factor on its self-inductance. For example, the selfinductance of a 2-AWG isolated wire (diameter = 0.26") is
about half the self-inductance of a 30-AWG wire (diameter
= 0.01"). One foot of 30-AWG wire has approximately
465nH of self-inductance. Two methods can reduce wire
self-inductance. One method divides the current flowing
towards the LT3086 between two parallel conductors. In
this case, the farther apart the wires are from each other,
the more the self-inductance is reduced; up to a 50%
reduction when placed a few inches apart. Splitting the
wires connects two equal inductors in parallel, but placing
them in close proximity creates mutual inductance adding to the self-inductance. The second and most effective
way to reduce overall inductance is to place both forward
3086fa
For more information www.linear.com/LT3086
LT3086
Applications Information
and return current conductors (the input and GND wires)
in very close proximity. Two 30-AWG wires separated by
only 0.02", used as forward- and return-current conductors, reduce the overall self-inductance to approximately
one-fifth that of a single isolated wire.
If a battery, mounted in close proximity, powers the LT3086,
a 10μF input capacitor suffices for stability. However, if a
distant supply powers the LT3086, use a larger value input
capacitor. Use a rough guideline of 1μF (in addition to the
10μF minimum) per 8 inches of wire length. The minimum
input capacitance needed to stabilize the application also
varies with power supply output impedance variations.
Placing additional capacitance on the LT3086’s output also
helps. However, this requires an order of magnitude more
capacitance in comparison with additional LT3086 input
bypassing. Series resistance between the supply and the
LT3086 input also helps stabilize the application; as little
as 0.1Ω to 0.5Ω suffices. This impedance dampens the
LC tank circuit at the expense of dropout voltage. A better alternative is to add additional input capacitance with
higher ESR at the input, such as tantalum or electrolytic
capacitors, or by adding resistance in series with a low
ESR ceramic capacitor.
Overload Recovery
Like many IC power regulators, the LT3086 has safe
operating area protection. The safe operating area protection decreases current limit as input-to-output voltage
increases, and keeps the power transistor inside a safe
operating region for all values of input-to-output voltage.
The LT3086 provides some output current at all values of
input-to-output voltage up to the specified 45V operational
maximum. Current limit foldback overrides external current
limit (if used) if VIN – VOUT voltage differential becomes
excessive.
When power is first applied, the input voltage rises and the
output follows the input; allowing the regulator to start-up
into very heavy loads. During start-up, as the input voltage
is rising, the input-to-output voltage differential is small,
allowing the regulator to supply large output currents.
With a high input voltage, a problem can occur wherein
the removal of an output short will not allow the output
to recover. Other regulators, such as the LT1083/LT1084/
LT1085 family and LT1764A also exhibit this phenomenon,
so it is not unique to the LT3086. The problem occurs with
a heavy output load when the input voltage is high and the
output voltage is low. Common situations are immediately
after the removal of a short-circuit or if the shutdown pin
is pulled high after the input voltage is already turned on.
The load line intersects the output current curve at two
points creating two stable output operating points for the
regulator. With this double intersection, the input power
supply needs to be cycled down to zero and brought up
again for the output to recover.
Thermal Considerations
The power handling capability of the LT3086 is limited by
the maximum rated junction temperature of 125°C. Three
components comprise the power dissipated by the device:
1.Output current multiplied by the input/output voltage
differential:
IOUT • (VIN − VOUT),
2.GND pin current multiplied by the input voltage:
IGND • VIN, and
3.Current monitor current multiplied by the input/current
monitor voltage differential:
IMON • (VIN − VIMON)
GND pin current is determined using the GND Pin Current
curves in the Typical Performance Characteristics section.
Power dissipation equals the sum of the three components
listed above.
The LT3086 regulators have internal thermal limiting
that protects the device during overload conditions. For
continuous normal conditions, the maximum junction
temperature of 125°C must not be exceeded. Carefully
consider all sources of thermal resistance from junctionto-ambient including other heat sources mounted in
proximity to the LT3086.
The underside of the LT3086 DFN and TSSOP packages
have exposed metal (10.5mm2) from the lead to the die
attachment. These packages allow heat to directly transfer
from the die junction to the printed circuit board metal.
The dual-in-line pin arrangement allows metal to extend
3086fa
For more information www.linear.com/LT3086
23
LT3086
Applications Information
beyond the ends of the package on the topside (component
side) of a PCB. Connect this metal to GND on the PCB.
The multiple IN and OUT pins of the LT3086 also assist
in spreading heat to the PCB.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes also can spread the heat generated by
power devices.
Tables 2 and 3 list thermal resistance for several topside
copper areas on a fixed board size. All measurements were
taken in still air on a 4-layer FR-4 board with 1oz solid
internal planes and 2oz top/bottom external trace planes
with a total board thickness of 1.6mm. The four layers
were electrically isolated with no thermal vias present.
Achieving low thermal resistance necessitates attention
to detail and careful PCB layout. For more information
on thermal resistance and high thermal conductivity
test boards, refer to JEDEC standard JESD51, notably
JESD51‑12 and JESD51-7. The use of thermal vias,
increased copper weight, and air flow, will improve the
resultant thermal resistance.
Table 2. Measured Thermal Resistance for DHD and FE Package
COPPER AREA
TOPSIDE*
BACKSIDE BOARD AREA
(mm2)
(mm2)
(mm2)
2500
2500
2500
1000
2500
2500
225
2500
2500
100
2500
2500
*Device is mounted on topside
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
25°C/W
26°C/W
28°C/W
33°C/W
Table 3. Measured Thermal Resistance for R Package
COPPER AREA
TOPSIDE*
BACKSIDE
(mm2)
(mm2)
2500
2500
1000
2500
225
2500
BOARD AREA
(mm2)
2500
2500
2500
*Device is mounted on topside
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
15°C/W
16°C/W
19°C/W
Measured Thermal Resistance for T7 Package
Thermal resistance (junction-to-case) = 3°C/W.
The LT3086 has the ability to check thermal performance
by observing the output current and temperature monitor
pins. The effects of heat sinking, the enclosure, and any
air movement can be instantly analyzed without special
instrumentation.
Calculating Junction Temperature
Example: Given an output voltage of 5V, an input voltage
range of 6V ±5%, a maximum output current range of 1A
with 698Ω for RMON, and a maximum ambient temperature
of 75°C, what will the maximum junction temperature be?
The power dissipated by the device equals:
IOUT(MAX) • (VIN(MAX) − VOUT) + IGND • VIN(MAX) +
IMON(MAX) • (VIN(MAX) − VIMON(MAX))
where,
IOUT(MAX) = 1A
VIN(MAX) = 6.3V
IGND at (IOUT = 1A, VIN = 6.3V) = 11mA
VIMON at (IOUT = 1A, RMON = 698Ω) = 0.698V
So:
P = 1A • (6.3V − 5V) + 11mA • 6.3V +
1mA • (6.3V − 0.698V) = 1.38W
Using a DFN package, the thermal resistance will be in the
range of 25°C/W to 33°C/W depending on the topside copper area. So the junction temperature rise above ambient
approximately equals:
1.38W • 30°C/W = 41.4°C
The maximum junction temperature equals the maximum
ambient temperature plus the maximum junction temperature rise above ambient or:
TJMAX = 75°C + 41.4°C = 116.4°C
Protection Features
The LT3086 regulator incorporates several protection
features that make it ideal for use in battery-powered
circuits. In addition to the normal protection features
24
3086fa
For more information www.linear.com/LT3086
LT3086
Applications Information
The LT3086 incurs no damage if its output is pulled below ground. If the input is left open-circuit or grounded,
the output can be pulled below ground by 36V. No current flows through the pass transistor from the output.
However, current flows in (but is limited by) the feedback
resistors RSET, that sets the output voltage, and RRPWRGD,
that sets the power good threshold. Current flows from
the internal clamps in the SET and RPWRGD pins to the
external circuitry pulling OUT below ground. If the input
is powered by a voltage source, the device protects itself
by turning off the power device when the internal clamps
activate. If Schottky diodes are used to prevent the SET
and RPWRGD pins from activating their internal clamps, the
output sources current equal to its current limit capability
and the LT3086 protects itself by thermal limiting. In this
case, grounding the SHDN pin turns off the device and
stops the output from sourcing current. Reverse current
flow follows the curve shown in Figure 14.
The LT3086 incurs no damage if the SET and RPWRGD
pins are pulled above ground up to 36V. If the input is
left open-circuit or grounded, the SET pin performs like a
large resistor (typically 80k) in series with a diode.
In circuits where a secondary supply raises the output
voltage above the regulated voltage set by RSET, the output
overshoot circuitry pulls current from the output pin to
ground as long as the output voltage is below the input
voltage. Output overshoot current follows the curve shown
REVERSE OUTPUT CURRENT (mA)
The LT3086 IN pin withstands reverse voltages of 45V. The
device limits current flow to less than 2mA (typically less
than 1μA) and no negative voltage appears at OUT. The
device protects both itself and the load against batteries
that are plugged in backwards.
0.6
TJ = 25°C
VIN = 0V
0.5 VOUT = VSET = VRPWRGD
CURRENT FLOWS THROUGH
PINS TO GROUND
0.4
0.3
SET
0.2
0.1
0
OUT, RPWRGD
0
4
8
12 16 20 24
OUTPUT VOLTAGE (V)
28
32
3086 F14
Figure 14. Reverse-Output Current
30
OUTPUT OVERSHOOT PULL-DOWN (mA)
Current limit protection and thermal overload protection
protect the device against current overload conditions at
the output of the device. The typical thermal shutdown
temperature is 165°C and incorporates about 7°C of hysteresis. For normal operation, do not exceed the maximum
rated junction temperature of 125°C.
in Figure 15. When the output voltage is pulled above
the input by typically 225mV, the LT3086 shuts down as
shown in Figure 16 and the 15mA overshoot pull-down
current source turns off.
TJ = 25°C
VIN = 0V
25 VOUT = VSET = VRPWRGD
CURRENT FLOWS THROUGH
OUT PIN TO GND
20
15
10
5
0
0
4
8
12 16 20 24 28
OUTPUT VOLTAGE (V)
32
36
3086 F15
Figure 15. Output Overshoot Pull-Down Current
OUT OVER IN SHUTDOWN THRESHOLD (mV)
associated with monolithic regulators, such as current
limiting and thermal limiting, the devices also protect
against reverse-input voltages, reverse-output voltages,
and reverse-output-to-input voltages.
300
275
250
ON TO OFF
225
200
175
150
OFF TO ON
125
100
75
50
25
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3086 F16
Figure 16. OUT Over IN Shutdown Threshold
3086fa
For more information www.linear.com/LT3086
25
LT3086
Typical Applications
2.5V Low Noise Regulator with Power Good
VIN
3.1V TO 13V
OUT
IN
10µF
RSET
42.2k
1%
LT3086
VTEMP
10mV/°C
25°C = 250mV
SHDN
SET
TEMP
RPWRGD
IMON
PWRGD
CSET
10nF
10µF
RPGSET
37.4k
1%
VOUT
2.5V AT 2.1A
RPGD
100k
VPWRGD HIGH
WHEN
VOUT > 90% of 2.5V
ILIM
GND
3086 TA09
1.2V, 1.5A Low Noise Regulator with 1.8A External Current Limit
VIN
1.65V TO 16V
IN
OUT
RSET
15.8k
1%
LT3086
10µF
SHDN
VTEMP
10mV/°C
25°C = 250mV
VMON
0.8V AT 1.8A
FULL-SCALE
10µF
CSET
10nF
200Ω
1%
TEMP
VOUT
1.2V AT 1.5A
SET
IMON
ILIM
RMON
442Ω
1%
GND
3086 TA10
5 White LED Driver with PWM Dimming and LED Open Detection
OUT
IN
VIN*
10µF
R4
100k
1%
LT1004-1.2
LT3086
SET
SHDN
R2
3.32k
1%
RMON
800Ω
R3
9.09k
1%
IMON
RPWRGD
ILIM
PWRGD
RSET
**
1%
RPGSET
**
1%
R1
1k
C1
10nF
RPGD
100k
1%
VOUT
10µF
VPWRGD HIGH
FOR OPEN LED
CONDITION
GND
3086 TA11
PWM
26
NOTE: ADJUST RMON TO SET MAXIMUM LED CURRENT (SET TO 800Ω FOR 1A)
DRIVE PWM LOW TO TURN OFF LED STRING (PULSE TO DIM)
*INPUT VOLTAGE REQUIRED IS DEPENDENT ON THE LED STRING VOLTAGE
**CHOOSE RSET AND RPGSET BASED ON LED STRING
3086fa
For more information www.linear.com/LT3086
LT3086
Typical Applications
Adjustable Voltage Controlled Current Source
10µF
LT3086
OUT
10µF
SHDN
IN
1µF
400mV
OUT
LT6650
FB
SET
TRACK
IMON
GND
1µF
ILIM
R1
1k
C1
10nF
VTRACK
ADJUST FROM 0V TO 750mV
FOR 0A TO 2.1A CONSTANT CURRENT
LOAD
IN
VIN*
GND
RMON
357Ω
1%
3086 TA12
*RESTRICT INPUT VOLTAGE RANGE TO LIMIT POWER DISSIPATION
AND PREVENT FOLDBACK CURRENT LIMIT FROM INTERFERING
WITH PROPER OPERATION
Ensuring External Current Limit Stability for ILIM ≤ 1A
VIN
12.5V TO 40V
IN
10µF
OUT
LT3086
SHDN
VIMON
800mV at 250mA
ADDITIONAL
R-C NETWORK
R1
1k
C1
10nF
SET
RSET
232k
1%
VOUT
12V AT 200mA
CSET
10nF
RLIM
3.24k
1%
VIN
3V TO 19V
IN
10µF
OUT
LT3086
(DHD ONLY)
SHDN
IMON
ILIM
Increasing Current Monitor Output Voltage
VIMON = 1V/A
10µF
GND
ILIMIT = 1.5A
SET
RSET
41.2k
1%
CSET
10nF
IMON
R1
464Ω
1%
ILIM
RLIM
536Ω
1%
VOUT
2.5V AT 1.2A
10µF
GND
3086 TA04
3086 TA05
 0.8V 
RLIM = 
 •1000
I
LIMIT
Increasing Power Good Hysteresis (Ex: 2%)
VIN
3.85V TO 18V
IN
OUT
LT3086
10µF
SHDN
SET
RSET
57.6k
1%
RPWRGD
RMON
442Ω
1%
IMON
ILIM
RPGSET
51.1k
1%
RHYS
3.65M
1%
PWRGD
GND
3086 TA06
RHYS =
10µF
VOUT
3.3V AT 1.5A
RPGD
100k
VPWRGD
VX •100 (P • VOUT – 0.4V )
VOUT (H–HINT ) ( 50µA )
WHERE, VX = RPGD TERMINATION VOLTAGE = VOUT
P = POWER GOOD TRIP THRESHOLD (% OF VOUT )
H = DESIRED PERCENTAGE HYSTERESIS
HINT = 0.6 (INTERNAL PERCENTAGE HYSTERESIS)
3086fa
For more information www.linear.com/LT3086
27
LT3086
Typical Applications
Load Current Monitoring Using Power Good
VIN
3.85V TO 18V
IN
OUT
SHDN
IMON
ILIM
R1
169Ω
1%
ILIMIT = 1.6A
 0.8V 
R1= 
•1000 –R2
 ILIMIT 
RSET
57.6k
1%
LT3086
10µF
SET
VOUT
3.3V AT 1.5A
RPGD
100k
RPWRGD
PWRGD
GND
VPWRGD
HIGH WHEN
ILOAD > 1.25A
R2
324Ω
1%
 0.4V 
R2 = 
•1000
 ILOAD 
10µF
C1 (OPTIONAL, FOR
POWERGOOD
FLAG DELAY)
3086 TA03
Input Undervoltage Detector Using Power Good
VIN
4V TO 18V
IN
OUT
RSET
57.6k
1%
LT3086
RPGSET
71.5k
1%
10µF
SHDN
RPWRGD
IMON
ILIM
RMON
442Ω
1%
SET
10µF
VOUT
3.3V AT 1.5A
RPGD
100k
PWRGD
GND
VPWRGD HIGH
WHEN
VIN > 4V
3086 TA07
Programming Thermal Limit Temperature
VIN
2.4V TO 12V
IN
10µF
VTEMP
100µA
LT3086
SHDN
VTEMP
10mV/°C
25°C = 250mV
124°C THERMAL LIMIT
R TEMP =
OUT
SET
RSET
28k
1%
CSET
10nF
10µF
VOUT
1.8V AT 2.1A
TEMP
RTEMP
12.4k
1%
RMON
332Ω
1%
IMON
ILIM
GND
3086 TA08
Paralleling Two Regulators for 5V, 4.2A
VIN
5.7V TO 15V
10µF
VTEMP(MASTER)
10mV/°C
25°C = 250mV
VOUT
RPGD
100k
VPWRGD
28
VOUT
5V AT 4.2A
IN SHDN OUT
LT3086
MASTER
10µF
RPGSET
82.5k
1%
TEMP
RPWRGD
RSET
90.9k
1%
1.1k
1%
OUT SHDN IN
10µF
CSET
10nF
SET
IMON
ILIM
PWRGD
GND
VILIM(MASTER)
0.7V AT 4.2A
RMON
332Ω
1%
RMON
332Ω
1%
LT3086
SLAVE
TEMP
10µF
VTEMP(SLAVE)
10mV/°C
25°C = 250mV
SET
TRACK
IMON
ILIM
GND
3086 TA02
3086fa
For more information www.linear.com/LT3086
LT3086
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
DHD Package
16-Lead Plastic DFN (5mm × 4mm)
(Reference LTC DWG # 05-08-1707 Rev A)
0.70 ±0.05
4.50 ±0.05
3.10 ±0.05
2.44 ±0.05
(2 SIDES)
PACKAGE
OUTLINE
0.25 ±0.05
0.50 BSC
4.34 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
5.00 ±0.10
(2 SIDES)
9
4.00 ±0.10
(2 SIDES)
R = 0.115
TYP
0.40 ±0.10
16
2.44 ±0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
PIN 1
NOTCH
8
0.200 REF
1
0.25 ±0.05
0.50 BSC
0.75 ±0.05
0.00 – 0.05
(DHD16) DFN REV A 1113
4.34 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJGD-2) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
3086fa
For more information www.linear.com/LT3086
29
LT3086
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
FE Package
16-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663 Rev J)
Exposed Pad Variation BB
4.70
(.185)
3.58
(.141)
DETAIL A
4.90 – 5.10*
(.193 – .201)
0.56
(.022)
REF
3.58
(.141)
NOTE 5
16 1514 13 12 1110
9
NOTE 5
6.60 ±0.10
2.94 3.05
(.116) (.120)
4.50 ±0.10
DETAIL A
SEE NOTE 4
2.94 6.40
(.116) (.252)
BSC
0.53
(.021)
REF
DETAIL A IS THE PART OF THE
LEAD FRAME FEATURE FOR
REFERENCE ONLY
NO MEASUREMENT PURPOSE
1.05 ±0.10
0.65 BSC
0.45 ±0.05
1 2 3 4 5 6 7 8
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.25
REF
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
30
1.10
(.0433)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE16 (BB) TSSOP REV J 1012
5. BOTTOM EXPOSED PADDLE MAY HAVE METAL PROTRUSION
IN THIS AREA. THIS REGION MUST BE FREE OF ANY EXPOSED
TRACES OR VIAS ON PBC LAYOUT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3086fa
For more information www.linear.com/LT3086
LT3086
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
R Package
7-Lead Plastic DD Pak
(Reference LTC DWG # 05-08-1462 Rev F)
.256
(6.502)
.060
(1.524)
TYP
.060
(1.524)
.390 – .415
(9.906 – 10.541)
.165 – .180
(4.191 – 4.572)
.045 – .055
(1.143 – 1.397)
15° TYP
.060
(1.524)
.183
(4.648)
+.008
.004 –.004
+0.203
0.102 –0.102
.059
(1.499)
TYP
.330 – .370
(8.382 – 9.398)
(
)
.095 – .115
(2.413 – 2.921)
.075
(1.905)
DETAIL A
.300
(7.620)
+.012
.143 –.020
+0.305
3.632 –0.508
(
BOTTOM VIEW OF DD PAK
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
)
.026 – .035
(0.660 – 0.889)
TYP
.050
(1.27)
BSC
.013 – .023
(0.330 – 0.584)
.050 ±.012
(1.270 ±0.305)
DETAIL A
0° – 7° TYP
.420
.080
.420
0° – 7° TYP
.276
.350
.325
.205
.585
.585
.320
.090
.050
.035
RECOMMENDED SOLDER PAD LAYOUT
NOTE:
1. DIMENSIONS IN INCH/(MILLIMETER)
2. DRAWING NOT TO SCALE
.090
.050
.035
RECOMMENDED SOLDER PAD LAYOUT
FOR THICKER SOLDER PASTE APPLICATIONS
R (DD7) 0212 REV F
3086fa
For more information www.linear.com/LT3086
31
LT3086
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
T7 Package
7-Lead Plastic TO-220 (Standard)
(Reference LTC DWG # 05-08-1422)
.390 – .415
(9.906 – 10.541)
.165 – .180
(4.191 – 4.572)
.147 – .155
(3.734 – 3.937)
DIA
.045 – .055
(1.143 – 1.397)
.230 – .270
(5.842 – 6.858)
.460 – .500
(11.684 – 12.700)
.570 – .620
(14.478 – 15.748)
.330 – .370
(8.382 – 9.398)
.620
(15.75)
TYP
.700 – .728
(17.780 – 18.491)
SEATING PLANE
.152 – .202
.260 – .320 (3.860 – 5.130)
(6.604 – 8.128)
BSC
.050
(1.27)
.026 – .036
(0.660 – 0.914)
.135 – .165
(3.429 – 4.191)
.095 – .115
(2.413 – 2.921)
.155 – .195*
(3.937 – 4.953)
.013 – .023
(0.330 – 0.584)
*MEASURED AT THE SEATING PLANE
T7 (TO-220) 0801
32
3086fa
For more information www.linear.com/LT3086
LT3086
Revision History
REV
DATE
DESCRIPTION
A
6/14
Added MP-grade for TSSOP, DD-Pak, and TO-220 packages
PAGE NUMBER
Added EC Table line item for Minimum Load Current and Note 16
Added and modified two GND Pin Current curves, two PSRR at 1A curves, two Line Regulation curves and modified
VOUT Noise curve
Updated Thermal Resistance for DHD, FE and R packages
Updated DHD Package Description
2 to 4
3, 5
7 to 12
2, 24
29
3086fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LT3086
33
LT3086
Typical Application
Paralleling Two Regulators for 5V, 4.2A with Cable Drop Compensation (CDC)
CABLE
RLINE1
10µF
VTEMP(MASTER)
10mV/°C
25°C = 250mV
IN SHDN OUT
LT3086
MASTER
TEMP
VOUT
10µF
SET
10µF
OUT SHDN IN
RSET
90.9k + 1.1k
1%
10µF
RCDC
1%
LT3086
SLAVE
SET
TEMP
VTEMP(SLAVE)
10mV/°C
25°C = 250mV
LOAD
VIN
6.4V TO 15V
FOR RWIRE = 0.2Ω
VLOAD
5V AT
4.2A
CDC
GND
IMON
ILIM
VILIM(MASTER)
0.7V AT 4.2A
RMON
332Ω
1%
RMON
332Ω
1%
RCDC =
TRACK
IMON
ILIM
GND
RLINE2
3086 TA13
RMON •RSET
( X +1) • 3000 •R WIRE
R WIRE = RLINE1 +RLINE2
WHERE X = NUMBER OF SLAVES
Related Parts
PART NUMBER DESCRIPTION
COMMENTS
LT1764/
LT1764A
3A, Fast Transient Response, Low
Noise LDO
340mV Dropout Voltage, Low Noise: 40μVRMS, VIN: 2.7V to 20V, TO-220 and DD Packages, -A
Version Stable Also with Ceramic Capacitors
LT1963/
LT1963A
1.5A, Low Noise, Fast Transient
Response LDO
340mV Dropout Voltage, Low Noise: 40μVRMS, VIN: 2.5V to 20V, -A Version Stable with Ceramic
Capacitors, TO-220, DD-Pak, SOT-223 and SO-8 Packages
LT1965
1.1A, Low Noise, Low Dropout
Linear Regulator
310mV Dropout Voltage, Low Noise: 40μVRMS, VIN: 1.8V to 20V, VOUT: 1.2V to 19.5V, Stable with
Ceramic Capacitors, TO-220, DD-Pak, MSOP and 3mm × 3mm DFN Packages
LT3022
1A, Low Voltage VLDO Linear
Regulator
145mV Dropout Voltage, VIN: 0.9V to 10V, VOUT: 0.2V to 9.5V, Stable with Low ESR, Ceramic
Output Capacitors, 16-Pin DFN (5mm × 3mm) and 16-Lead MSOP Packages
LT3070
5A, Low Noise, Programmable VOUT, 85mV Dropout Voltage, Digitally Programmable VOUT: 0.8V to 1.8V, Digital Output Margining:
85mV Dropout Linear Regulator with ±1%, ±3% or ±5%, Low Output Noise: 25μVRMS; Directly Parallelable, Stable with Low ESR
Digital Margining
Ceramic Output Capacitors (15μF Minimum), 28-Lead 4mm × 5mm QFN Package
LT3071
5A, Low Noise, Programmable VOUT, 85mV Dropout Voltage, Digitally Programmable VOUT: 0.8V to 1.8V, Analog Margining: ±10%, Low
85mV Dropout Linear Regulator with Output Noise: 25μVRMS; Directly Parallelable, IMON Output Current Monitor, Stable with Low ESR
Analog Margining
Ceramic Output Capacitors (15μF Minimum), 28-Lead 4mm × 5mm QFN Package
LT3080/
LT3080-1
1.1A, Parallelable, Low Noise, Low
Dropout Linear Regulator
LT3081
1.5A, Single Resistor Rugged Linear Extended Safe Operating Area, VIN: 1.2V to 36V, VOUT: 0V to 34.5V, Current-Based Reference,
Regulator with Monitors
Programmable Current Limit, Output Current and Temperature Monitors
LT3083
3A, Parallelable, Low Noise, Low
Dropout Linear Regulator
310mV Dropout Voltage (2-Supply Operation), Low Noise: 40μVRMS, VIN: 1.2V to 23V, VOUT:
0V to 22.6V, Current-Based Reference with 1-Resistor VOUT Set, Directly Parallelable (No Op
Amp Required), Stable with Ceramic Capacitors; TO-220, DD-Pak, TSSOP, 4mm × 4mm DFN-12
Packages
LT3085
500mA, Parallelable, Low Noise,
Low Dropout Linear Regulator
275mV Dropout (2-Supply Operation), Low Noise: 40μVRMS, VIN: 1.2V to 36V, VOUT: 0V to 35.7V,
Current-Based Reference with 1-Resistor VOUT Set, Directly Parallelable (No Op Amp Required),
Stable with Ceramic Capacitors; MS8E and 2mm × 3mm DFN-6 Packages
300mV Dropout Voltage (2-Supply Operation), Low Noise: 40μVRMS, VIN: 1.2V to 36V, VOUT: 0V
to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Amp
Required), Stable with Ceramic Capacitors; TO-220, DD-Pak, SOT-223, MSOP and 3mm × 3mm
DFN-8 Packages; -1 Version Has Integrated Internal Ballast Resistor
34 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LT3086
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LT3086
3086fa
LT 0614 REV A • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2013