ALTAIR05T-800 Off-line all-primary-sensing switching regulator Features ■ Constant voltage and constant current output regulation (CV/CC) with no optocoupler ■ Tight regulation also in presence of heavy load transients ■ 800 V avalanche rugged internal power section ■ Quasi-resonant (QR) operation ■ Low standby power consumption ■ Automatic self-supply ■ Input voltage feedforward for mainsindependent cc regulation ■ Output cable drop compensation ■ SO16 package SO16N Applications ■ AC-DC chargers for mobile phones and other hand-held equipments ■ Compact SMPS that requires a precise current and/or voltage regulation Description ALTAIR05T-800 is a high-voltage all-primary sensing switcher intended for operating directly from the rectified mains with minimum external parts. It combines a high-performance lowvoltage PWM controller chip and an 800 V avalanche-rugged power section in the same package. Figure 1. Block diagram +Vout +Vin Is tart -up Vcc Internal supply bus PROTECTION & FEEDFORWARD LOGIC DRAIN SUPPLY & UV LO Vref UVLO Prot CDC Rcdc Rzcd IFF Iout ESTIMATE ZCD/FB BLANKING TIME Vc STARTER 3.3 V TURN-ON LOGIC Vc DEMAG LOGIC Rfb R R Q Q LEB + R S Q 1V Iref - + S/H S S Intern. supp ly bus I FF - UVLO R + Prot + 2.5 V RFF COMP GND IREF Rcomp Cref SOURCE Rsense Ccomp October 2010 Doc ID 17957 Rev 1 1/28 www.st.com 28 Contents ALTAIR05T-800 Contents 1 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.1 Power section and gate driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.2 High-voltage start-up generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.3 Zero current detection and triggering block . . . . . . . . . . . . . . . . . . . . . . . 13 5.4 Constant voltage operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.5 Constant current operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.6 Voltage feedforward block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.7 Cable drop compensation (CDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.8 Burst-mode operation at no load or very light load . . . . . . . . . . . . . . . . . . 20 5.9 Soft-start and starter block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.10 Hiccup mode OCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.11 Layout recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2/28 Doc ID 17957 Rev 1 ALTAIR05T-800 1 Device description Device description The device combines two silicon in the same package: a low voltage PWM controller and an 800 V avalanche rugged power section. The controller chip is a current-mode specifically designed for offline quasi-resonant flyback converters. The device features a unique characteristic: it is capable of providing constant output voltage (CV) and constant output current (CC) regulation using primary-sensing feedback. This eliminates the need for the optocoupler, the secondary voltage reference, as well as the current sensor, still maintaining quite accurate regulation also in presence of heavy load transients. Additionally, it is possible to compensate the voltage drop on the output cable, so as to improve CV regulation on the external accessible terminals. Quasi-resonant operation is guaranted by means of a transformer demagnetization sensing input that turns on the power section. The same input serves also the output voltage monitor, to perform CV regulation, and the input voltage monitor, to achieve mainsindependent CC regulation (line voltage feedforward). The maximum switching frequency is top-limited below 166 kHz, so that at medium-light load a special function automatically lowers the operating frequency still maintaining the valley switching operation. At very light load, the device enters a controlled burst-mode operation that, along with the built-in high-voltage start-up circuit and the low operating current, helps minimize the standby power. Although an auxiliary winding is required in the transformer to correctly perform CV/CC regulation, the chip is able to power itself directly from the rectified mains. This is useful especially during CC regulation, where the flyback voltage generated by the winding drops below UVLO threshold. However, if ultra-low no-load input consumption is required to comply with the most stringent energy-saving recommendations, then the device needs to be powered via the auxiliary winding. In addition to these functions that optimize power handling under different operating conditions, the device offers protection features that considerably increase end-product’s safety and reliability: auxiliary winding disconnection - or brownout – detection and shorted secondary rectifier - or transformer’s saturation – detection. All of them are auto restart mode. Doc ID 17957 Rev 1 3/28 Pin connection 2 ALTAIR05T-800 Pin connection Figure 2. Pin connection (top view) SOURCE 1 16 DRAIN SOURCE 2 15 DRAIN Vcc 3 14 DRAIN GND 4 13 DRAIN IREF 5 12 N.C. ZCD/FB 6 11 N.A. COMP 7 10 N.A. CDC 8 9 N.A. Note: The copper area for heat dissipation has to be designed under the drain pins Table 1. Pin functions N. 1, 2 Function Power section source and input to the PWM comparator. The current flowing in the MOSFET is sensed through a resistor connected between the pin and GND. The resulting voltage is compared with an internal reference (0.75V max.) to determine MOSFET’s turn-off. The pin SOURCE is equipped with 250 ns blanking time after the gate-drive output goes high for improved noise immunity. If a second comparison level located at 1V is exceeded the IC is stopped and restarted after Vcc has dropped below 5V. 3 Vcc Supply Voltage of the device. An electrolytic capacitor, connected between this pin and ground, is initially charged by the internal high-voltage start-up generator; when the device is running the same generator keeps it charged in case the voltage supplied by the auxiliary winding is not sufficient. This feature is disabled in case a protection is tripped. Sometimes a small bypass capacitor (0.1 µF typ.) to GND might be useful to get a clean bias voltage for the signal part of the IC. 4 GND Ground. Current return for both the signal part of the IC and the gate drive. All of the ground connections of the bias components should be tied to a trace going to this pin and kept separate from any pulsed current return. IREF CC regulation loop reference voltage. An external capacitor has to be connected between this pin and GND. An internal circuit develops a voltage on this capacitor that is used as the reference for the MOSFET’s peak drain current during CC regulation. The voltage is automatically adjusted to keep the average output current constant. 5 4/28 Name Doc ID 17957 Rev 1 ALTAIR05T-800 Table 1. N. Pin connection Pin functions (continued) Name Function 6 ZCD/FB Transformer’s demagnetization sensing for quasi-resonant operation. Input/output voltage monitor. A negative-going edge triggers MOSFET’s turn-on. The current sourced by the pin during ON-time is monitored to get an image of the input voltage to the converter, in order to compensate the internal delay of the current sensing circuit and achieve a CC regulation independent of the mains voltage. If this current does not exceed 50µA, either a floating pin or an abnormally low input voltage is assumed, the device is stopped and restarted after Vcc has dropped below 5V. Still, the pin voltage is sampled-and-held right at the end of transformer’s demagnetization to get an accurate image of the output voltage to be fed to the inverting input of the internal, transconductance-type, error amplifier, whose non-inverting input is referenced to 2.5V. Please note that the maximum IZCD/FB sunk/sourced current has to not exceed ±2 mA (AMR) in all the Vin range conditions (85-265 Vac). No capacitor is allowed between the pin and the auxiliary transformer. 7 COMP Output of the internal transconductance error amplifier. The compensation network is placed between this pin and GND to achieve stability and good dynamic performance of the voltage control loop. 8 CDC Cable drop compensation input. During CV regulation this pin, capable of sinking current, provides a voltage lower than the internal reference voltage (2.5V) by an amount proportional to the dc load current. By connecting a resistor between this pin and ZCD/FB, the CV regulation setpoint is increased proportionally. This allows that the voltage drop across the output cable be compensated and, ideally, that zero load regulation at the externally available terminals be achieved. Leave the pin open if the function is not used. 9-11 N.A Not available. These pins must be left not connected 12 N.C Not internally connected. Provision for clearance on the PCB to meet safety requirements. 13 to 16 DRAIN Drain connection of the internal power section. The internal high-voltage start-up generator sinks current from this pin as well. Pins connected to the internal metal frame to facilitate heat dissipation. Doc ID 17957 Rev 1 5/28 Maximum ratings ALTAIR05T-800 3 Maximum ratings 3.1 Absolute maximum ratings Table 2. Symbol VDS ID Eav Absolute maximum ratings Pin Value Unit -1 to 800 V 1,2, 13-16 Drain current 1 A 1,2, 13-16 Single pulse avalanche energy (Tj = 25°C, ID = 1A) 50 mJ 1,2, 13-16 Drain-to-source (ground) voltage Vcc 3 Supply voltage (Icc < 25mA) Self limiting V IZCD/FB 6 Zero current detector current ±2 mA --- 7, 8 -0.3 to 3.6 V ICDC 8 Maximum sunk current 200 µA Power dissipation @TA = 50°C 0.9 W Junction temperature range -25 to 150 °C Storage temperature -55 to 150 °C Ptot Tj Tstg 3.2 Analog inputs and outputs Thermal data Table 3. Symbol 6/28 Parameter Thermal data Parameter Max. value Unit Rth j-pin Thermal resistance, junction-to-pin 10 Rth j-amb Thermal resistance, junction-to-ambient 110 Doc ID 17957 Rev 1 °C/W ALTAIR05T-800 4 Electrical characteristics Electrical characteristics (TJ = -25 to 125 °C, Vcc = 14 V; unless otherwise specified) Table 4. Electrical characteristics Symbol Parameter Test condition Min. Typ. Max. Unit Power section V(BR)DSS Drain-source breakdown IDSS RDS(on) Coss ID< 100 µA; Tj = 25 °C 800 V VDS = 750 V; Tj = 125 °C (See Figure 4 and note) Off state drain current 80 Id=100 mA; Tj = 25 °C 11 14 Id=100 mA; Tj = 125 °C 22 28 Drain-source ON-state resistance µA Ω Effective (energy-related) output capacitance (See Figure 3) High-voltage start-up generator VStart Min. Drain start voltage Icharge < 100 µA 40 50 60 V Icharge Vcc startup charge current VDRAIN> VStart; VCC<VCCOn Tj = 25 °C 4 5.5 7 mA 9.5 10.5 11.5 (1) VCCrestart Vcc restart voltage (Vcc falling) V After protection tripping 5 Supply voltage Vcc Operating range After turn-on VccOn Turn-on threshold (1) 12 Turn-off threshold (1) Zener voltage Icc = 20 mA VccOff VZ 11.5 23 V 13 14 V 9 10 11 V 23 25 27 V (See Figure 5) 200 300 µA Supply current Iccstart-up Start-up current Iq Quiescent current (See Figure 6) 1 1.4 mA Icc Operating supply current @ 50 kHz (See Figure 7) 1.4 1.7 mA Fault quiescent current During hiccup and brownout (See Figure 8) 250 350 µA 100 125 175 µs 400 500 700 µs 0.1 1 µA 3.3 3.6 V Iq(fault) Start-up timer TSTART Start timer period TRESTART Restart timer period during burst mode Zero current detector IZCDb Input bias current VZCD = 0.1 to 3 V VZCDH Upper clamp voltage IZCD = 1 mA Doc ID 17957 Rev 1 3.0 7/28 Electrical characteristics Table 4. ALTAIR05T-800 Electrical characteristics (continued) Symbol Parameter Test condition Min. Typ. Max. Unit VZCDL Lower clamp voltage IZCD = - 1 mA -90 -60 -30 mV VZCDA Arming voltage positive-going edge 100 110 120 mV VZCDT Triggering voltage negative-going edge 50 60 70 mV IZCDON Min. source current during MOSFET ON-time -25 -50 -75 µA TBLANK Trigger blanking time after MOSFET’s turn-off VCOMP ≥ 1.3V 6 VCOMP = 0.9V 30 IZCD = 1mA 45 µs Line feedforward RFF Equivalent feedforward resistor Ω Transconductance error amplifier Tj = 25°C (1) 2.46 Tj = -25 to 125°C and Vcc=12V to 23V (1) 2.42 1.3 VREF Voltage reference gm Transconductance ∆ICOMP = ±10 µA VCOMP = 1.65 V Gv Voltage gain Open loop GB Gain-bandwidth product 2.5 2.54 V 2.58 2.2 3.2 mS 73 dB 500 KHz Source current VZCD = 2.3V, VCOMP = 1.65V 70 100 µA Sink current VZCD = 2.7V, VCOMP = 1.65V 400 750 µA VCOMPH Upper COMP voltage VZCD = 2.3 V 2.7 V VCOMPL Lower COMP voltage VZCD = 2.7 V 0.7 V 1 V 65 mV ICOMP VCOMPBM Burst-mode threshold Hys Burst-mode hysteresis CDC function VCDC CDC voltage reference VCOMP = 1.1V, ICDC = 1µA (1) 2.4 2.5 2.6 V VCOMP = VCOMPL (1) 1.5 1.6 1.7 V 0.192 0.2 0.208 V 200 250 300 ns Current reference VIREFx Maximum value VCREF Current reference voltage Current sense tLEB Leading-edge blanking td(H-L) Delay-to-output VCSx VCSdis 300 Max. clamp value dVcs/dt = 200 mV/µs Hiccup-mode OCP level (1) 1. Parameters tracking each other 8/28 Doc ID 17957 Rev 1 (1) ns 0.7 0.75 0.8 V 0.92 1 1.08 V ALTAIR05T-800 Figure 3. Electrical characteristics COSS output capacitance variation 500 C OSS (pF) 400 300 200 100 0 0 25 50 75 100 125 150 V DS (V) Figure 4. Off state drain and source current test circuit 14 V VD D CDC 2. 5V F B /Z C D + Ids s D R AI N C U R R EN T C ON TR OL C OMP Note: A GN D IR E F Vin 75 0V SOU R C E The measured IDSS is the sum between the current across the start-up resistor and the effective MOSFET’s off state drain current. Figure 5. Start-up current test circuit Ic cst art-up FB/ ZC D 1 1.8 V VDD CDC 2. 5V A + D R AIN C U R R EN T C ON TR OL C OMP IR EF Doc ID 17957 Rev 1 GN D SOU R C E 9/28 Electrical characteristics Figure 6. ALTAIR05T-800 Quiescent current test circuit Iq_ m eas A VD D CDC 2.5 V F B/ Z C D D R AI N + C U R R EN T C ON TR OL - 3 3k C OMP I R EF GN D SOU R C E 0 .8 V 3V Figure 7. 1 4V 10 k 0.2 V Operating supply current test circuit Ic c 1. 5k 2W 15V A 27 k VD D CDC 22 0k 2. 5V F B /Z C D 10 k 1 0k + C U R R EN T C ON TR OL - 150V C OMP Note: SOU R C E 5. 6 2. 8V -5V The circuit across the ZCD pin is used for switch-on synchronization Figure 8. Quiescent current during fault test circuit I q(f au lt ) 2. 5V F B/ Z C D A 14V VDD CDC + D R AIN C U R R EN T C ON TR OL C OMP 10/28 GN D I R EF 10 50 kH z D R AIN IR EF Doc ID 17957 Rev 1 GN D SOU R C E ALTAIR05T-800 5 Application information Application information The device is an off-line all-primary sensing switching regulator, based on quasi-resonant flyback topology. Depending on converter’s load condition, the device is able to work in different modes (see Figure 9): 1. QR mode at heavy load. Quasi-resonant operation lies in synchronizing MOSFET's turn-on to the transformer’s demagnetization by detecting the resulting negative-going edge of the voltage across any winding of the transformer. Then the system works close to the boundary between discontinuous (DCM) and continuous conduction (CCM) of the transformer. As a result, the switching frequency is different for different line/load conditions (see the hyperbolic-like portion of the curves in Figure 9). Minimum turn-on losses, low EMI emission and safe behavior in short circuit are the main benefits of this kind of operation. 2. Valley-skipping mode at medium/ light load. Depending on voltage on COMP pin, the device defines the maximum operating frequency of the converter. As the load is reduced MOSFET’s turn-on does not occur any more on the first valley but on the second one, the third one and so on. In this way the switching frequency is no longer increased (piecewise linear portion in Figure 9). 3. Burst-mode with no or very light load. When the load is extremely light or disconnected, the converter enters a controlled on/off operation with constant peak current. Decreasing the load result in frequency reduction, which can go down even to few hundred hertz, thus minimizing all frequency-related losses and making it easier to comply with energy saving regulations or recommendations. Being the peak current very low, no issue of audible noise arises. Figure 9. Multi-mode operation of ALTAIR05T-800 f osc Input voltage f sw Valley-skipping mode Burst-mode Quasi-resonant mode 0 Pin Doc ID 17957 Rev 1 Pinmax 11/28 Application information 5.1 ALTAIR05T-800 Power section and gate driver The power section guarantees safe avalanche operation within the specified energy rating as well as high dv/dt capability. The Power MOSFET has a V(BR)DSS of 800 V min. and a typical RDS(on) of 11 Ω. The gate driver is designed to supply a controlled gate current during both turn-on and turnoff in order to minimize common mode EMI. Under UVLO conditions an internal pull-down circuit holds the gate low in order to ensure that the power MOSFET cannot be turned on accidentally. 5.2 High-voltage start-up generator The HV current generator is supplied through the DRAIN pin and it is enabled only if the input bulk capacitor voltage is higher than Vstart threshold, 50 VDC typically. When the HV current generator is ON, the Icharge current (5.5 mA typical value) is delivered to the capacitor on the VCC pin. With reference to the timing diagram of Figure 10, when power is applied to the circuit and the voltage on the input bulk capacitor is high enough, the HV generator is sufficiently biased to start operating, thus it draws about 5.5 mA (typical) from the bulk capacitor. Most of this current charges the bypass capacitor connected between the Vcc pin and ground and make its voltage rise linearly. As the Vcc voltage reaches the start-up threshold (13 V typ.) the chip starts operating, the internal power MOSFET is enabled to switch and the HV generator is cut off. The IC is powered by the energy stored in the Vcc capacitor. The chip is able to power itself directly from the rectified mains: when the voltage on the VCC pin falls below Vccrestart (10.5V typ.), during each MOSFET’s off-time the HV current generator is turned on and charges the supply capacitor until it reaches the VCCOn threshold. In this way, the self-supply circuit develops a voltage high enough to sustain the operation of the device. This feature is useful especially during CC regulation, when the flyback voltage generated by the auxiliary winding alone may not be able to keep Vcc above VCCrestart. At converter power-down the system loses regulation as soon as the input voltage falls below VStart. This prevents converter’s restart attempts and ensures monotonic output voltage decay at system power-down. 12/28 Doc ID 17957 Rev 1 ALTAIR05T-800 Application information Figure 10. Timing diagram: normal power-up and power-down sequences Vin VStart Vcc t VccON Vccrestart t DRAIN Icharge t 5.5 mA Normal operation CV mode Power-on t Power-off Zero current detection and triggering block The zero current detection (ZCD) and triggering blocks switch on the power MOSFET if a negative-going edge falling below 50 mV is applied to the ZCD/FB pin. To do so, the triggering block must be previously armed by a positive-going edge exceeding 100 mV. This feature is used to detect transformer demagnetization for QR operation, where the signal for the ZCD input is obtained from the transformer’s auxiliary winding used also to supply the IC. Figure 11. ZCD block, triggering block R zcd ZCD/FB BLANKIN G TIME Z CD CLAMP STARTER Rfb Aux TU RN- ON LO GIC 110mV 60mV S + 5.3 Normal operation CC mode Q Fr om CC/ CV Bloc k LEB To Dr iv er R Fr om OC P The triggering block is blanked after MOSFET’s turn-off to prevent any negative-going edge that follows leakage inductance demagnetization from triggering the ZCD circuit erroneously. This blanking time is dependent on the voltage on COMP pin: it is TBLANK = 30 µs for VCOMP = 0.9 V, and decreases almost linearly down to TBLANK = 6 µs for VCOMP = 1.3 V Doc ID 17957 Rev 1 13/28 Application information ALTAIR05T-800 The voltage on the pin is both top and bottom limited by a double clamp, as illustrated in the internal diagram of the ZCD block of Figure 11. The upper clamp is typically at 3.3 V, while the lower clamp is at -60 mV. The interface between the pin and the auxiliary winding is a resistor divider. Its resistance ratio as well as the individual resistance values has to be properly chosen (see “Section 5.4: Constant voltage operation” and “Section 5.6: Voltage feedforward block”). Please note that the maximum IZCD/FB sunk/sourced current has to not exceed ±2 mA (AMR) in all the Vin range conditions (85-265 Vac). No capacitor is allowed between ZCD pin and the auxiliary transformer. The switching frequency is top-limited below 166 kHz, as the converter’s operating frequency tends to increase excessively at light load and high input voltage. A Starter block is also used to start-up the system, that is, to turn on the MOSFET during converter power-up, when no or a too small signal is available on the ZCD pin. The starter frequency is 2 kHz if COMP pin is below burst mode threshold, i.e. 1 V, while it becomes 8 kHz if this voltage exceed this value. After the first few cycles initiated by the starter, as the voltage developed across the auxiliary winding becomes large enough to arm the ZCD circuit, MOSFET’s turn-on starts to be locked to transformer demagnetization, hence setting up QR operation. The starter is activated also when the IC is in CC regulation and the output voltage is not high enough to allow the ZCD triggering. If the demagnetization completes – hence a negative-going edge appears on the ZCD pin – after a time exceeding time TBLANK from the previous turn-on, the MOSFET is turned on again, with some delay to ensure minimum voltage at turn-on. If, instead, the negative-going edge appears before TBLANK has elapsed, it is ignored and only the first negative-going edge after TBLANK turns-on the MOSFET. In this way one or more drain ringing cycles is skipped (“valley-skipping mode”, Figure 12) and the switching frequency is prevented from exceeding 1/TBLANK. Figure 12. Drain ringing cycle skipping as the load is progressively reduced VDS VDS VDS TON TFW TV Tosc t t Tosc Pin = Pin' (limit condition) Tosc Pin = Pin'' < Pin' Pin = Pin''' < P in'' Note that when the system operates in valley skipping-mode, uneven switching cycles may be observed under some line/load conditions, due to the fact that the OFF-time of the MOSFET is allowed to change with discrete steps of one ringing cycle, while the OFF-time needed for cycle-by-cycle energy balance may fall in between. Thus one or more longer switching cycles is compensated by one or more shorter cycles and vice versa. However, this mechanism is absolutely normal and there is no appreciable effect on the performance of the converter or on its output voltage. 14/28 Doc ID 17957 Rev 1 ALTAIR05T-800 5.4 Application information Constant voltage operation The IC is specifically designed to work in primary regulation and the output voltage is sensed through a voltage partition of the auxiliary winding, just before the auxiliary rectifier diode. Figure 13 shows the internal schematic of the constant voltage mode and the external connections. Figure 13. Voltage control principle: internal schematic Rzcd S/ H - EA + Rfb + Aux 2. 5V D EMAG LOGI C To PWM Logic CV F rom Rsense COMP R C Due to the parasitic wires resistance, the auxiliary voltage is representative of the output just when the secondary current becomes zero. For this purpose, the signal on ZCD/FB pin is sampled-and-held at the end of transformer’s demagnetization to get an accurate image of the output voltage and it is compared with the error amplifier internal reference. The COMP pin is used for the frequency compensation: usually, an RC network, which stabilizes the overall voltage control loop, is connected between this pin and ground. The output voltage can be defined according the formula: V REF R FB = --------------------------------------------------------- ⋅ R ZCD N AUX -------------- ⋅ V OUT – V REF N SEC (1) Where NSEC and NAUX are the secondary and auxiliary turn’s number respectively. The RZCD value can be defined depending on the application parameters (see “Section 5.6: Voltage feedforward block”). 5.5 Constant current operation Figure 14 presents the principle used for controlling the average output current of the flyback converter. Doc ID 17957 Rev 1 15/28 Application information ALTAIR05T-800 The output voltage of the auxiliary winding is used by the demagnetization block to generate the control signal for the mosfet switch Q1. A resistor R in series with it absorbs a current VC/R, where VC is the voltage developed across the capacitor CREF. The flip-flop’s output is high as long as the transformer delivers current on secondary side. This is shown in Figure 15. The capacitor CREF has to be chosen so that its voltage VC can be considered as a constant. Since it is charged and discharge by currents in the range of some ten µA (ICREF is typically 20 µA) at the switching frequency rate, a capacitance value in the range 4.7-10 nF is suited for switching frequencies in the ten kHz. The average output current can be expressed as: N PRI V CREF I OUT = -------------- ⋅ ------------------------------------N SEC ( 2 ⋅ R SENSE ) (2) Where NPRI is the primary's turns number. This formula shows that the average output current does not depend anymore on the input or the output voltage, neither on transformer inductance values. The external parameters defining the output current are the transformer ratio n and the sense resistor RSENSE. Figure 14. Current control principle . Ir ef To PWM Logic CC + R F rom Rsense R zcd Q1 S ZCD/FB Q DEMAG LOGI C R Rfb Aux IREF Cref 16/28 Doc ID 17957 Rev 1 ALTAIR05T-800 Application information Figure 15. Constant current operation: Switching cycle waveforms T IP t Is t Q t I CREF IC ICRE F = − 5.6 VC R t Voltage feedforward block The current control structure uses the voltage VC to define the output current, according to (2). Actually, the CC comparator is affected by an internal propagation delay Td, which switches off the MOSFET with a peak current than higher the foreseen value. This current overshoot is equal to: ∆IP = VIN ⋅ Td LP (3) Where LP is the primary inductance. It introduces an error on the calculated CC setpoint, depending on the input voltage. The device implements a Line Feedforward function, which solves the issue by introducing an input voltage dependent offset on the current sense signal, in order to adjust the cycleby-cycle current limitation. The internal schematic is shown in Figure 16. Doc ID 17957 Rev 1 17/28 Application information ALTAIR05T-800 Figure 16. Feedforward compensation: internal schematic DRAIN ZCD/FB F eedf orward Logic . Rfb Aux I FF CC Block - R zcd CC PWM LOGI C + Rf f SOURCE Rsense The RZCD resistor can be calculated as follows: RZCD = NAUX ⋅ LP ⋅ RFF NPRI Td ⋅ RSENSE (4) In this case the peak drain current does not depend on input voltage anymore. One more consideration concerns the RZCD value: during MOSFET’s ON-time, the current sourced by the ZCD/FB pin, IZCD, is compared with an internal reference current IZCDON (-50 µA typical). If IZCD < IZCDON, the brownout function is activated and the IC is shut-down. This feature is especially important when the auxiliary winding is accidentally disconnected and considerably increases the end-product’s safety and reliability. 5.7 Cable drop compensation (CDC) The voltage control loop regulates the output voltage as seen across the output capacitor. If an output cable is used to supply the load, the voltage at the externally available terminals is dependent on the output current value. The CDC function compensates the voltage drop across the cable, so ideally zero load regulation can be achieved also at the end of the cable. 18/28 Doc ID 17957 Rev 1 ALTAIR05T-800 Application information Figure 17 presents the internal schematic. Figure 17. CDC block: internal schematic Dsec Vout Vout_reg Rcable/2 N pr i Nsec Cout R cable/ 2 Rzcd GND N aux Viref Rcdc CDC To C V Compar ator CDC LOGIC Vr ef ZCD/FB F B Block Rf b COMP During CV regulation, as the CDC block is capable of sinking current, a resistor connect between its output and ZCD/FB pin allows to increase the CV setpoint, by providing a voltage lower than the internal reference voltage by an amount proportional to the average load current. If RCABLE is the total cable resistance, the resistor value can be calculated by using the following equation: 2 ⋅ N SEC N SEC R SENSE ⋅ R ZCD R CDC = ------------------------- ⋅ -------------- ⋅ -------------------------------------------N PRI R CABLE N AUX (5) In this equation RCABLE is the total resistance of the output cable. The CDC block acts as an outer control loop with a positive feedback that changes the CV setpoint. As such, it can impact on the overall system’s stability. In order to avoid any issue that could make unstable the loop, the CV setpoint response time must be much slower than that of the inner voltage loop. For this purpose the CDC block is designed with a time response of a few ten ms. For the same reason, the minimum voltage on CDC pin is bottom limited at to 2.25 V. If the function is not required, the pin can be connected to ground or left open. Doc ID 17957 Rev 1 19/28 Application information 5.8 ALTAIR05T-800 Burst-mode operation at no load or very light load When the voltage at the COMP pin falls 65 mV below a threshold fixed internally at a value, VCOMPBM, the IC is disabled with the MOSFET kept in OFF state and its consumption reduced at a lower value to minimize Vcc capacitor discharge. In this condition the converter operates in burst-mode (one pulse train every TSTART=500 µs), with minimum energy transfer. As a result of the energy delivery stop, the output voltage decreases: after 500 µs the controller switches-on the MOSFET again and the sampled voltage on the ZCD pin is compared with the internal reference. If the voltage on the EA output, as a result of the comparison, exceeds the VCOMPL threshold, the device restarts switching, otherwise it stays OFF for another 500 µs period. In this way the converter works in burst-mode with a nearly constant peak current defined by the internal disable level. Then a load decrease causes a frequency reduction, which can go down even to few hundred hertz, thus minimizing all frequency-related losses and making it easier to comply with energy saving regulations. This kind of operation, shown in the timing diagrams of Figure 18 along with the others previously described, is noise-free since the peak current is low Figure 18. Load-dependent operating modes: timing diagrams COMP 65 mV hyster. VCOMPL IDS Normal-mode 5.9 TSTART TSTART TSTART Burst-mode TSTART Normal-mode Soft-start and starter block The soft start feature is automatically implemented by the constant current block, as the primary peak current is limited from the voltage on the CREF capacitor. During start-up, as the output voltage is zero, the IC starts in CC mode with no high peak current operations. In this way the voltage on the output capacitor increases slowly and the soft-start feature is ensured. Actually the CREF value is not important to define the soft-start time, as its duration depends on others circuit parameters, like transformer ratio, sense resistor, output capacitors and load. The user can define the best appropriate value by experiments. 20/28 Doc ID 17957 Rev 1 ALTAIR05T-800 5.10 Application information Hiccup mode OCP The device is also protected against short circuit of the secondary rectifier, short circuit on the secondary winding or a hard-saturated flyback transformer. A comparator monitors continuously the voltage on the RSENSE and activates a protection circuitry if this voltage exceeds 1 V. To distinguish an actual malfunction from a disturbance (e.g. induced during ESD tests), the first time the comparator is tripped the protection circuit enters a “warning state”. If in the subsequent switching cycle the comparator is not tripped, a temporary disturbance is assumed and the protection logic is reset in its idle state; if the comparator is tripped again a real malfunction is assumed and the device is stopped. This condition is latched as long as the device is supplied. While it is disabled, however, no energy is coming from the self-supply circuit; hence the voltage on the VCC capacitor decays and cross the UVLO threshold after some time, which clears the latch. The internal start-up generator is still off, then the VCC voltage still needs to go below its restart voltage before the VCC capacitor is charged again and the device restarted. Ultimately, this results in a lowfrequency intermittent operation (Hiccup-mode operation), with very low stress on the power circuit. This special condition is illustrated in the timing diagram of Figure 19. Figure 19. Hiccup-mode OCP: timing diagram Secondary diode is shorted here VCC VccON VccOFF Vccrest VSOURCE Vcsdis t 1V t Two switching cycles VDS t 5.11 Layout recommendations A proper printed circuit board layout is essential for correct operation of any switch-mode converter and this is true for the ALTAIR05T-800 as well. Careful component placing, correct traces routing, appropriate traces widths and compliance with isolation distances are the major issues. In particular: ● The compensation network should be connected as close as possible to the COMP pin, maintaining the trace for the GND as short as possible ● Signal Ground should be routed separately from power ground, as well from the sense resistor trace. Doc ID 17957 Rev 1 21/28 Application information ALTAIR05T-800 Figure 20. Suggested routing for converter OUT AC IN AC IN GND CDC FB/ZCD COMP 22/28 DRAIN VDD ALTAIR05T-800 GND Doc ID 17957 Rev 1 IREF SOURCE ALTAIR05T-800 6 Typical application Typical application Figure 21. Test board schematic: 5 W wide range mains CC/CV battery charger L1 AC IN BR MB6S- RC R1 T1 470uH 5V - 1A STPS3L40U F C1 4.7uF 400V 22 1W D7 C3 1nF C2 4. 7uF 400V R2 120K C9 680uF Low ESR R9 2. 2k AC IN D7 STTH1L06 R3 GN D 4 7K D2 R4 BAT46 10 C4 10uF R5 U1 ALTAIR 05 TBD VDD CD C 2. 5V F B/ ZC D + 2 .2nF - Y Cap C UR R ENT C ON TR OL IR EF C O MP R6 10 K GN D T1 SPECIFICATION Supplier: MAGNETICA SOU R CE C5 470nF C7 4. 7nF C6 1nF Table 5. C 10 D RAI N R7 10k R8 1.2 Core E16/8/5, f er rite N67 Gap: 0.18mm for 2.2mH primary inductance Lleakage max= 88uH Pr imar y: 125T, AWG34 Auxiliar y: 25T, AWG34 Secondary: 9T, 0.50 Tex-E Efficiency at 115 VAC Load [%] IOUT[A] VOUT[V] POUT[W] PIN[W] Efficiency [%] 25 0.25 4.97 1.243 1.643 75.62 50 0.5 4.97 2.485 3.156 78.64 75 0.75 4.97 3.728 4.72 78.97 100 1 4.98 4.980 6.4 77.81 Average efficiency Table 6. 77.79 Efficiency at 230 VAC Load [%] IOUT[A] VOUT[V] POUT[W] PIN[W] Efficiency [%] 25 0.25 4.98 1.245 1.88 66.22 50 0.5 4.97 2.485 3.349 74.18 75 0.75 4.98 3.735 4.838 77.22 100 1 4.99 4.990 6.326 78.88 Average efficiency Doc ID 17957 Rev 1 74.12 23/28 Package mechanical data 7 ALTAIR05T-800 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 7. SO16N mechanical data Mm inch Dim. Min Typ A a1 Min Typ 1.75 0.1 Max 0.069 0.25 a2 0.004 0.009 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 c1 0.020 45° (typ.) D (1) 9.8 10 0.386 0.394 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F(1) 3.8 4.0 0.150 0.157 G 4.60 5.30 0.181 0.208 L 0.4 1.27 0.150 0.050 M S 24/28 Max 0.62 0.024 8 °(max.) Doc ID 17957 Rev 1 ALTAIR05T-800 Package mechanical data Figure 22. Package dimensions Doc ID 17957 Rev 1 25/28 Order codes 8 ALTAIR05T-800 Order codes Table 8. Ordering information Order code Package ALTAIR05T-800 ALTAIR05T-800TR 26/28 Packaging Tube SO16N Tape and reel Doc ID 17957 Rev 1 ALTAIR05T-800 9 Revision history Revision history Table 9. Document revision history Date Revision 25-Oct-2010 1 Changes Initial release. Doc ID 17957 Rev 1 27/28 ALTAIR05T-800 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 28/28 Doc ID 17957 Rev 1