Data Sheet

HV
QF
N3
2
IP4787CZ32
DVI and HDMI interface ESD protection, DDC/CEC buffering,
hot plug handling and backdrive protection
Rev. 3 — 19 December 2014
Product data sheet
1. Product profile
1.1 General description
The IP4787CZ32 is designed to protect High-Definition Multimedia Interface (HDMI)
receiver interfaces. It includes HDMI 5 V power management, Display Data
Channel (DDC) buffering and decoupling, hot plug drive, backdrive protection, Consumer
Electronic Control (CEC) buffering and decoupling, and 12 kV contact ElectroStatic
Discharge (ESD) protection for all external I/Os, exceeding the IEC 61000-4-2, level 4
standard.
The IP4787CZ32 incorporates Transmission Line Clamping (TLC) technology on the
high-speed Transition-Minimized Differential Signaling (TMDS) lines to simplify routing
and help reduce impedance discontinuities. All TMDS lines are protected by an
impedance-matched diode configuration that minimizes impedance discontinuities caused
by typical shunt diodes.
The 5 V power management enables host access to the [Extended Display Identification
Data (EDID)] memory even if no HDMI plug is connected. The overall load to the 5 V line
is according to the HDMI requirements.
The DDC lines use a buffering concept which decouples the internal capacitive load from
the external capacitive load for use with standard Complementary Metal Oxide
Semiconductor (CMOS) or Low Voltage Transistor-Transistor Logic (LVTTL) I/O cells
down to 1.2 V. This buffering also redrives the DDC and CEC signals, allowing the use of
longer or cheaper HDMI cables with a higher capacitance. The internal hot plug drive
module simplifies the application of the HDMI receiver to control the hot plug signal.
All lines provide appropriate integrated pull-ups and pull-downs for HDMI compliance and
backdrive protection to guarantee that HDMI interface signals are not pulled down if the
system is powered down or enters Standby mode. Only a single external capacitor is
required for operation.
1.2 Features and benefits




HDMI 2.0 and all backward compatible standards are supported
6.0 Gbps TMDS bit rate (600 Mcsc TMDS character rate) compatible
Supports UHD 4k (2160p) 60 Hz display modes
Impedance matched 100  differential transmission line ESD protection for
TMDS lines (10 ). No Printed-Circuit Board (PCB) pre-compensation required
 Simplified flow-through routing utilizing less overall PCB space
 DDC capacitive decoupling between system side and HDMI connector side and
buffering to drive cable with high capacitive load (> 700 pF/25 m)
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
 All external I/O lines with ESD protection of at least 12 kV, exceeding the
IEC 61000-4-2, level 4 standard
 Hot plug drive module
 Utility biasing module (HEAC compliant)
 CEC buffering and isolation, with integrated backdrive-protected 26 k pull-up
 Robust ESD protection without degradation after repeated ESD strikes
 Highest integration in a small footprint, PCB level, optimized RF routing,
32-pin HVQFN leadless package
1.3 Applications
 The IP4787CZ32 can be used for a wide range of HDMI sink devices, consumer and
computing electronics:
 Digital High-Definition (HD) TV
 Set-top box
 PC monitor
 Projector
 Multimedia audio amplifier
 HDMI picture performance quality enhancer module
 Digital Visual Interface (DVI)
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
2 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
2. Pinning information
&(&B&21
9&&6<6
(6'B%<3$66
$&7,9(
&(&B6<6
(1$%/(B/'2
WHUPLQDO
LQGH[DUHD
QF
+273/8*B&75/
2.1 Pinning
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B6<6
70'6B'B6<6
70'6B'B&21
70'6B&.B6<6
70'6B&.B&21
70'6B&.B6<6
70'6B&.B&21
70'6B'B&21
87,/,7<B&21 70'6B'B&21
''&B&/.B&21 ''&B'$7B&21 +'0,B9B&21 +273/8*B&21 9&&9 ''&B&/.B6<6
''&B'$7B6<6 ,3&=
DDD
7UDQVSDUHQWWRSYLHZ
Fig 1.
Pin configuration IP4787CZ32
2.2 Pin description
Table 1.
IP4787CZ32
IP4787CZ32
Pin description
Pin
Name
Description
1
TMDS_D2+_SYS
TMDS to ASIC inside system
2
TMDS_D2_SYS
TMDS to ASIC inside system
3
TMDS_D1+_SYS
TMDS to ASIC inside system
4
TMDS_D1_SYS
TMDS to ASIC inside system
5
TMDS_D0+_SYS
TMDS to ASIC inside system
6
TMDS_D0_SYS
TMDS to ASIC inside system
7
TMDS_CK+_SYS
TMDS to ASIC inside system
8
TMDS_CK_SYS
TMDS to ASIC inside system
9
DDC_CLK_SYS
DDC clock system side
10
DDC_DAT_SYS
DDC data system side
11
VCC(5V0)
5 V supply input
12
HOTPLUG_CON
hot plug output to connector
13
HDMI_5V0_CON
5 V input from connector
14
DDC_DAT_CON
DDC data connector side
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
3 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 1.
Pin description …continued
Pin
Name
Description
15
DDC_CLK_CON
DDC clock connector side
16
UTILITY_CON
utility line ESD protection
17
TMDS_CK_CON
TMDS ESD protection to connector
18
TMDS_CK+_CON
TMDS ESD protection to connector
19
TMDS_D0_CON
TMDS ESD protection to connector
20
TMDS_D0+_CON
TMDS ESD protection to connector
21
TMDS_D1_CON
TMDS ESD protection to connector
22
TMDS_D1+_CON
TMDS ESD protection to connector
23
TMDS_D2_CON
TMDS ESD protection to connector
24
TMDS_D2+_CON
TMDS ESD protection to connector
25
CEC_CON
CEC signal connector side
26
ESD_BYPASS
ESD bias voltage
27
VCC(SYS)
supply voltage for level shifting
28
ACTIVE
CEC Standby mode control (LOW for lowest
power, CEC-only mode)
29
CEC_SYS
CEC I/O signal system side
30
ENABLE_LDO
5 V LDO enable
31
n.c.
not connected
32
HOTPLUG_CTRL
hot plug control input from system side
ground pad
GND
ground
3. Ordering information
Table 2.
Ordering information
Type number
Package
Name
IP4787CZ32
IP4787CZ32
IP4787CZ32
Description
Version
HVQFN32 plastic thermal enhanced very thin quad flat package; SOT617-3
no leads; 32 terminals; body 5  5  0.85 mm
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
4 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
4. Functional diagram
TMDS_D2+_SYS
TMDS_D2+_CON
ESD
TMDS_D2–_SYS
TMDS_D2–_CON
TMDS_D1+_SYS
TMDS_D1+_CON
TMDS_D1–_SYS
TMDS_D1–_CON
TMDS_D0+_SYS
TMDS_D0+_CON
TMDS_D0–_SYS
TMDS_D0–_CON
TMDS_CK+_SYS
TMDS_CK+_CON
TMDS_CK–_SYS
TMDS_CK–_CON
INT_5V0
ESD
3.3 V VOLTAGE
REGULATOR
INT_VCC(SYS)
ESD
CEC driver
10 kΩ
26 kΩ
CEC_SYS
CEC_CON
ESD
HDMI_5V0_CON
INT_VCC(SYS)
ESD
DDC driver
3.65 kΩ
47 kΩ
DDC_CLK_SYS
DDC_CLK_CON
INT_VCC(SYS)
ESD
HDMI_5V0_CON
ESD
DDC driver
3.65 kΩ
47 kΩ
DDC_DAT_SYS
DDC_DAT_CON
Hot plug driver / bias
ESD
ESD
HOTPLUG_CTRL
HOTPLUG_CON
100 kΩ
ESD
Utility bias
ESD
UTILITY_CON
VCC(5V0)
INT_5V0
INT_VCC(SYS)
ESD
ESD
680 kΩ
HDMI_5V0_CON
ENABLE_LDO
5V Control
VCC(SYS)
INT_5V0
ESD
ESD
enable
enLim
enRef
POWER
MANAGEMENT UNIT
ACTIVE
enCEC
VCC(SYS)
VCC(SYS)
680 kΩ
INT_5V0
ibias 1..n
vref 1..m
ESD
n
ESD_BYPASS
m
INT_VCC(SYS)
CURRENT-/VOLTAGEREFERENCES
aaa-004322
Fig 2.
IP4787CZ32
IP4787CZ32
Functional diagram
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
5 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
5. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC(5V0)
supply voltage (5.0 V)
VI
input voltage
I/O pins
VESD
electrostatic discharge
voltage
IEC 61000-4-2, level 4 (contact)
[1]
-
12
kV
IEC 61000-4-2, level 1 (contact)
[2]
-
2
kV
total power dissipation
DDC operating at 100 kHz;
CEC operating at 1 kHz;
50 % duty cycle; ACTIVE = HIGH
-
50
mW
DDC and CEC bus in idle mode;
ACTIVE = HIGH
-
3.0
mW
DDC and CEC bus in idle mode;
ACTIVE = LOW
-
1.2
mW
Ptot
Conditions
Min
Max
GND  0.5 6.5
GND  0.5 5.5
Unit
V
V
Tamb
ambient temperature
25
+85
C
Tstg
storage temperature
55
+125
C
[1]
Connector-side pins (typically denoted with ‘_CON’ suffix) to ground.
[2]
System-side pins: CEC_SYS, DDC_DAT_SYS, DDC_CLK_SYS, HOTPLUG_CTRL, ACTIVE, VCC(SYS) and VCC(5V0).
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
6 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
6. Static characteristics
Table 4.
Supplies
Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
VCC(5V0)
supply voltage (5.0 V)
Conditions
V(HDMI_5V0_CON)
voltage on pin HDMI_5V0_CON
VCC(SYS)
system supply voltage
[1]
[1]
Min
Typ
Max
Unit
4.5
5.0
6.5
V
4.5
5.0
6.5
V
1.1
3.3
3.63
V
HDMI_5V0_CON is used as supply in case ENABLE_LDO is inactive and VCC(5V0) is unavailable or lower than HDMI_5V0_CON.
Table 5.
TMDS protection circuit
Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
90
100
110

-
0.6
-
pF
6.0
-
9.0
V
-
1.0
-

-
1.0
-

-
1.0
-

-
1.0
-

-
0.1
1.0
A
-
1.0
-
A
-
0.7
-
V
-
8.0
-
V
TMDS channel
Zi(dif)
differential input impedance
TDR measured; tr = 200 ps
Ceff
effective capacitance
equivalent shunt capacitance for
TDR minimum; tr = 200 ps
[1][2]
Protection diode
VBRzd
Zener diode breakdown voltage
I = 1.0 mA
rdyn
dynamic resistance
surge; I = 1.0 A; IEC 61000-4-5/9
positive transient
negative transient
TLP
[3]
positive transient
negative transient
Ibck
back current
VCC(5V0) < Vch(TMDS)
VI = 3.0 V
ILR
reverse leakage current
VF
forward voltage
VCL(ch)trt(pos)
positive transient channel
clamping voltage
100 ns TLP; 50  pulser at 50 ns
[1]
This parameter is guaranteed by design.
[2]
Capacitive dip at HDMI Time Domain Reflectometer (TDR) measurement conditions.
[4][5]
[3]
ANSI-ESD SP5.5.1-2004, ESD sensitivity testing Transmission Line Pulse (TLP) component level method 50 TDR.
[4]
Signal pins:
TMDS_D0+_CON, TMDS_D0_CON, TMDS_D1+_CON, TMDS_D1_CON, TMDS_D2+_CON, TMDS_D2_CON, TMDS_CK+_CON,
TMDS_CK_CON,
TMDS_D0+_SYS, TMDS_D0_SYS, TMDS_D1+_SYS, TMDS_D1_SYS, TMDS_D2+_SYS, TMDS_D2_SYS, TMDS_CK+_SYS
and TMDS_CK_SYS.
[5]
Backdrive current from TMDS_x_SYS and TMDS_x_CON pins to local VCC(5V0) bias rail at power-down. Device does not block
backdrive current leakage through the device to/from ASIC I/O pins connected to TMDS_x_SYS pins.
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
7 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 6.
HDMI_5V0_CON
Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
dynamic resistance
rdyn
Conditions
Min
Typ
Max
Unit
positive transient
-
1.0
-

negative transient
-
1.0
-

-
8
-
V
[1]
TLP
VCL
clamping voltage
100 ns TLP; 50  pulser at 50 ns
II(max)
maximum input current
V(HDMI_5V0_CON) = 5.3 V
Ibck
back current
VCC(5V0) < V(HDMI_5V0_CON)
[2]
-
-
50
mA
-
-
10
A
[1]
ANSI-ESD SP5.5.1-2004, ESD sensitivity testing TLP component level method 50 TDR.
[2]
Ibck defines the current that flows from the VCC(5V0) pin into the system supply. This parameter is guaranteed by design.
Table 7.
Static characteristics
Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
V
DDC_CLK_CON; DDC_DAT_CON[1]
VIH
HIGH-level input voltage
0.5 
V(HDMI_5V0_CON)
6.5
VIL
LOW-level input voltage
0.5
-
0.3 
V
V(HDMI_5V0_CON)
VOH
HIGH-level output voltage
V(HDMI_5V0_CON)  0.02
V(HDMI_5V0_CON) V
+ 0.02
VOL
LOW-level output voltage
internal pull-up and
external sink
-
100
200
mV
VIK
input clamping voltage
II = 18 mA
-
-
1.0
V
-
8.0
10
pF
42.3
47
51.7
k
VCC(SYS) = 1.2 V
310
-
-
mV
VCC(SYS) = 1.8 V
450
-
-
mV
VCC(SYS) = 2.5 V
620
-
-
mV
VCC(SYS) = 3.3 V
760
-
-
mV
VCC(SYS) = 1.2 V
-
-
240
mV
VCC(SYS) = 1.8 V
-
-
330
mV
VCC(SYS) = 2.5 V
-
-
370
mV
-
-
390
mV
CIO
input/output capacitance
Rpu
pull-up resistance
DDC_CLK_SYS;
VIH
VIL
[2]
VCC(5V0) = 5.0 V;
VCC(SYS) = 3.3 V;
ACTIVE = HIGH
[2][3]
DDC_DAT_SYS[1][4]
HIGH-level input voltage
LOW-level input voltage
VCC(SYS) = 3.3 V
VOH
HIGH-level output voltage
VOL
LOW-level output voltage
VIK
IP4787CZ32
IP4787CZ32
input clamping voltage
0.8  VCC(SYS)
-
VCC(SYS) + 0.02 V
VCC(SYS) = 1.2 V
-
330
340
mV
VCC(SYS) = 1.8 V
-
490
500
mV
VCC(SYS) = 2.5 V
-
640
690
mV
VCC(SYS) = 3.3 V
-
685
790
mV
II = 18 mA
-
-
1.0
V
[2]
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
8 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 7.
Static characteristics …continued
Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
CIO
input/output capacitance
Rpu
pull-up resistance
Conditions
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
[2]
Min
Typ
Max
Unit
-
6.0
8.0
pF
3.2
3.65
4.1
k
CEC_CON[1]
VIH
HIGH-level input voltage
2.0
-
-
V
VIL
LOW-level input voltage
-
-
0.80
V
VOH
HIGH-level output voltage
2.88
3.3
3.63
V
VOL
LOW-level output voltage
IOL = 1.5 mA
CIO
input/output capacitance
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 1.65 V;
AC input = 2.5 V(p-p);
f = 100 kHz
Rpu
pull-up resistance
Ileak(CEC)
CEC leakage current
-
100
200
mV
-
8.0
10
pF
23.4
26.0
28.6
k
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
CEC_CON connected
to 3.63 V via 27 k
-
-
0.1
µA
VCC(SYS) = 1.2 V
310
-
-
mV
VCC(SYS) = 1.8 V
450
-
-
mV
VCC(SYS) = 2.5 V
620
-
-
mV
VCC(SYS) = 3.3 V
760
-
-
mV
VCC(SYS) = 1.2 V
-
-
240
mV
VCC(SYS) = 1.8 V
-
-
330
mV
VCC(SYS) = 2.5 V
-
-
370
mV
-
-
390
mV
[2]
CEC_SYS[1][4]
VIH
VIL
HIGH-level input voltage
LOW-level input voltage
VCC(SYS) = 3.3 V
VOH
HIGH-level output voltage
VOL
LOW-level output voltage
0.8  VCC(SYS)
-
VCC(SYS) + 0.02 V
VCC(SYS) = 1.2 V
-
330
340
mV
VCC(SYS) = 1.8 V
-
490
500
mV
VCC(SYS) = 2.5 V
-
640
690
mV
-
675
770
mV
-
6.0
7.0
pF
8.5
10
11.5
k
[2]
VCC(SYS) = 3.3 V
CIO
input/output capacitance
Rpu
pull-up resistance
IP4787CZ32
IP4787CZ32
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 1.65 V;
AC input = 2.5 V(p-p);
f = 100 kHz
[2]
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
9 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Table 7.
Static characteristics …continued
Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
HOTPLUG_CON;
Conditions
Min
Typ
Max
Unit
4.4
V
UTILITY_CON[1]
VOH
HIGH-level output voltage
3.6
4
VOL
LOW-level output voltage
-
-
0.4
V
RO
output resistance
0.8
1.0
1.2
k
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
[2]
-
8.0
10
pF
output capacitance
CO
HOTPLUG_CTRL[1]
VIH
HIGH-level input voltage
HIGH = hot plug on
[5]
1.0
-
-
V
VIL
LOW-level input voltage
LOW = hot plug off
[5]
-
-
0.4
V
Rpd
pull-down resistance
60
100
140
k
VCC(5V0) = 0 V;
VCC(SYS) = 0 V;
Vbias = 2.5 V;
AC input = 3.5 V(p-p);
f = 100 kHz
[2]
-
6.0
7.0
pF
input capacitance
Ci
[1]
The device is active if the input voltage at pin ACTIVE is above the HIGH level.
[2]
This parameter is guaranteed by design.
[3]
Capacitive load measured at power-on.
[4]
No external pull-up resistor attached.
[5]
See Section 9.7 for details on the hot plug functionality.
Table 8.
Power management
VCC(SYS) = 1.10 V to 3.63 V; VCC(5V0) = 4.5 V to 6.5 V; GND = 0 V; Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
System side: input pin ACTIVE[1]
VIH
HIGH-level input voltage
VIL
LOW-level input voltage
Rpd
pull-down resistance
Ci
input capacitance
HIGH = active
[2]
1.0
-
-
V
LOW = standby
[3]
-
-
0.4
V
VI = 3 V or 0 V
[4]
-
6
7
pF
-
-
V
-
0.4
680
k
System side: input pin ENABLE_LDO
VIH
HIGH-level input voltage
1.0
VIL
LOW-level input voltage
-
Rpu
pull-up resistance
Ci
input capacitance
[1]
680
VI = 3 V or 0 V
[4]
-
6
V
k
7
pF
The ACTIVE pin should be connected permanently to VCC(5V0) or VCC(SYS) if no enable control is needed.
[2]
DDC buffers, Hot Plug Detect (HPD) driver, utility bias and HDMI_5V0_CON out enabled; CEC buffer enabled.
[3]
DDC buffers, HPD driver, utility bias and HDMI_5V0_CON out disabled; CEC buffer enabled.
[4]
This parameter is guaranteed by design.
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
10 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
7. Dynamic characteristics
Table 9.
Dynamic characteristics
VCC(5V0) = 5.0 V; VCC(SYS) = 1.8 V; GND = 0 V; Tamb = 25 C to +85 C unless otherwise specified.
Symbol
Parameter
Conditions
DDC_DAT_SYS, DDC_CLK_SYS, DDC_DAT_CON,
Min
Typ
Max
Unit
DDC_CLK_CON[1]
tPLH
LOW to HIGH propagation delay
system side to connector side Figure 16
-
80
-
ns
tPHL
HIGH to LOW propagation delay
system side to connector side Figure 16
-
60
-
ns
tPLH
LOW to HIGH propagation delay
connector side to system side Figure 17
-
120
-
ns
tPHL
HIGH to LOW propagation delay
connector side to system side Figure 17
-
80
-
ns
tTLH
LOW to HIGH transition time
connector side Figure 18
-
150
-
ns
tTHL
HIGH to LOW transition time
connector side Figure 18
-
100
-
ns
tTLH
LOW to HIGH transition time
system side Figure 19
-
250
-
ns
tTHL
HIGH to LOW transition time
system side Figure 19
-
80
-
ns
[1]
All dynamic measurements are done with a 75 pF load. Rise times on system side are determined only by internal pull-up resistors. Rise
times on connector side are determined by external 1.5 k and internal pull-up resistors.
DDD
=GLI
ȍ
70'6B&.
70'6B'
70'6B'
70'6B'
WLPHQV
tr = 200 ps; no filter; VCC(5V0) = 5 V
100  differential (CH1 + CH2)
Fig 3.
Differential TDR plot
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
11 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa086
3
Sdd21;
Scc21
(dB)
(1)
–3
(2)
–9
–15
106
107
108
109
1010
f (Hz)
(1) Sdd21
(2) Scc21
Normalized to 100 ; differential pairs at signal pins.
Fig 4.
Mixed-mode differential and common-mode insertion loss; typical values
018aaa087
3
Sdd21
(dB)
(1)
–3
(2)
–9
–15
106
107
108
109
1010
f (Hz)
(1) Sdd21; Near End Crosstalk (NEXT)
(2) Sdd21; Far End Crosstalk (FEXT)
normalized to 100 ; differential pairs CH1/CH2 versus CH3/CH4
Fig 5.
IP4787CZ32
IP4787CZ32
Mixed-mode differential and common-mode NEXT / FEXT; typical values
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
12 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
DDD
227 MHz pixel clock
Horizontal scale: 200 mV/div
Vertical scale: 90 ps/div
Offset: 42.6 mV
Fig 6.
Eye diagram using IP4787CZ32 (1080p, 12 bit)
DDD
297 MHz pixel clock
Horizontal scale: 200 mV/div
Vertical scale: 67.5 ps/div
Offset: 42.6 mV
Fig 7.
IP4787CZ32
IP4787CZ32
Eye diagram using IP4787CZ32 (1080p, 16 bit)
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
13 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
aaa-013775
148.5 MHz test frequency
Horizontal scale: 53.8 ps/div
Vertical scale: 200 mV/div
Measured at TP2 with worst cable emulator, reference cable equalizer and
worst case negative skew
Fig 8.
Eye diagram using IP4787CZ32 (2160p, 60 Hz)
018aaa090
0.4
Cline
(pF)
0.2
0.0
–0.2
–0.4
–1.0
1.0
3.0
5.0
7.0
Vbias (V)
Deviation from typical capacitance normalized at Vbias = 2.5 V
Fig 9.
IP4787CZ32
IP4787CZ32
Eye diagram using IP4787CZ32 (2160p, 60 Hz)
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
14 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa091
4.00
VCL
(V)
018aaa092
2.5
VCL
(V)
3.75
2.0
3.50
1.5
3.25
3.00
0.5
0.6
0.7
0.8
0.9
1.0
1.1
I (A)
1.2
1.0
0.4
0.6
0.8
1.0
1.2
I (A)
IEC 61000-4-5; tp = 8/20 s; positive pulse
IEC 61000-4-5; tp = 8/20 s; negative pulse
Fig 10. Dynamic resistance with positive clamping
Fig 11. Dynamic resistance with negative clamping
018aaa093
14
I
(A)
12
10
–4
8
–6
6
–8
4
–10
2
–12
0
6
10
14
18
22
018aaa094
0
I
(A)
–2
–14
–12
VCL (V)
tp = 100 ns; TLP; signal pins; typical values
IP4787CZ32
–4
0
VCL (V)
tp = 100 ns; TLP; signal pins; typical values
Fig 12. Dynamic resistance with positive clamping
IP4787CZ32
–8
Fig 13. Dynamic resistance with negative clamping
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
15 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
018aaa095
6.5
VI
(V)
018aaa096
6.0
VO
(V)
6.0
(2)
(5)
(4)
(1)
4.0
5.5
(1)
2.0
(3)
5.0
(4)
(3)
(2)
4.5
5.0
5.5
6.0
6.5
0.0
0.00
0.02
0.04
VCC(5V0) (V)
(1) 5.3 V; maximum values; HDMI CTS TID 7-11
(1) VCC(5V0) = 4.5 V
(2) 4.8 V; minimum values; HDMI CTS TID 7-11
(2) VCC(5V0) = 5.0 V
(3) I = 0 mA
(3) VCC(5V0) = 5.5 V
(4) I = 55 mA
(4) VCC(5V0) = 6.5 V
0.06
0.08
0.10
0.12
IO (A)
0.14
(5) VCC(5V0) supply input; 4.925 V to 6.5 V
Fig 14. Overvoltage limiter function (HDMI_5V0_CON)
IP4787CZ32
IP4787CZ32
Fig 15. Overcurrent limiter function (HDMI_5V0_CON)
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
16 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
8. AC waveforms
8.1 DDC propagation delay
9&&6<6
''&V\VWHPVLGH
9&&6<6
92/6<6
9,/6<6
''&FRQQHFWRUVLGH
9,17B9
9,17B9
9,17B9
92/&21
W3+/
W3/+
DDD
Fig 16. Propagation delay DDC, DDC system side to DDC connector side
9,17B9
''&FRQQHFWRUVLGH
9,17B9
9,17B9
9,/&21
9&&6<6
''&V\VWHPVLGH
9&&6<6
W3+/
9&&6<6
W3/+
92/6<6
DDD
Fig 17. Propagation delay DDC, DDC connector side to DDC system side
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
17 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
8.2 DDC transition time
''&V\VWHPVLGH
9&&6<6
9,/6<6
,17B9
''&FRQQHFWRUVLGH
9,17B9
9,17B9
92/&21
W3/+
W3+/
DDD
Fig 18. Transition time DDC connector side
,17B9
''&FRQQHFWRUVLGH
9,/&21
9&&6<6
''&V\VWHPVLGH
9&&6<6
9&&6<6
W3+/
W3/+
92/6<6
DDD
Fig 19. Transition time DDC system side
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
18 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9. Application information
9.1 HDMI connector side ESD protection
All pins directly interfacing with the HDMI connector provide up to 12 kV contact ESD
protection according to IEC 61000-4-2, exceeding level 4. In order to utilize the full scope
of this protection it is recommended to connect all connector side pins to the HDMI
connector.
9.2 TMDS ESD protection concept
To protect the TMDS lines and also to comply with the impedance requirements of the
HDMI specification, the IP4787CZ32 provides ESD protection with matched
TLC ESD structures. Typical Dual Rail Clamp (DRC) or rail-to-rail shunt structures are
common for low-capacitance ESD protection (Figure 20; left side) where the dominant
factor for the TMDS line impedance dip is determined by the capacitive load to ground.
Parasitic lead inductances of the packaging in this case work against the ESD clamping
performance by including the I/t reactance of the inductance into the path of the ESD
shunt.
The IP4787CZ32 utilizes these inherent inductances in series with the transmission line in
order to present an effective capacitive load of roughly only 0.7 pF. This TLC structure
minimizes the capacitive dip, for ideal signal integrity (Figure 20; right side) without
complicated PCB pre-compensation. As a beneficial side effect, this enhances the
ESD performance of the device as well, since the reactance of the series inductance
attenuates the fast initial peak of the ESD pulse for a lower residual pulse delivered to the
Application Specific Integrated Circuit (ASIC).
018aaa102
018aaa101
a. Classic parallel ESD shunt protection
b. Improved series shunt TLC clamping
Fig 20. TLC ESD protection of TMDS lines
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
19 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.3 Operating and standby modes
The operating mode of IP4787CZ32 depends on the availability of the VCC(5V0) and
VCC(SYS) supply voltages and on the state of the ACTIVE input signal. Without availability
of both supplies, IP4787CZ32 is in Standby mode. As soon as VCC(5V0) and VCC(SYS) are
within the range specified in Section 6, the part is in an operating mode that can be
controlled via the ACTIVE input signal. In case ACTIVE is LOW, only the CEC buffer is
active and enabled to receive or send CEC commands. All other outputs are in a
high-ohmic state. A HIGH input signal enables all parts of IP4787CZ32 and puts the
device into full operating mode.
Table 10.
IP4787CZ32 operating modes
VCC(SYS)
VCC(5V0)
ACTIVE[1] Mode
Description
< 1.1 V
< 4.5 V
X
Standby mode
all outputs high-ohmic
 1.1 V
 4.5 V
L
CEC Standby mode
CEC circuit active;
all other outputs high-ohmic
H
full operating mode
all functional blocks active
[1]
X = Don’t care (either LOW or HIGH level); L = LOW-level input; H = HIGH-level input
If no CEC Standby mode is required, or if no special Power-down modes are desired, the
ACTIVE pin can be pulled HIGH to VCC(5V0) or VCC(SYS) for continuous HDMI and CEC
operation as soon as the supplies are aviailable.
Strapping the ACTIVE = VCC(SYS) = VDD of ASIC guarantees that all interface signals
ending with the suffix ‘_SYS’ on the system side are disabled when VCC(SYS) goes LOW,
protecting the ASIC I/O signals from exceeding its local VDD. In this mode, even if VCC(5V0)
is powered, HDMI_5V0_CON goes active and hot plug events can be detected only when
the ASIC power supply rail is on.
Strapping ACTIVE = VCC(5V0) is the most basic configuration where the buffers are
enabled whenever the local VCC(5V0) and VCC(SYS) supplies reach minimum operating
levels.
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
20 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.4 DDC circuit
The DDC bus circuit integrates all required pull-ups, and provides full capacitive
decoupling between the HDMI connector and the DDC bus lines on the PCB. The
capacitive decoupling ensures that the maximum capacitive load is well within the 50 pF
maximum of the HDMI specification. No external pull-ups or pull-downs are required.
The bidirectional buffers support high-capacitive load on the HDMI cable-side. Various
non-compliant but prevalent low-cost cables have been observed with a capacitive load of
up to 6 nF on the DDC lines, far exceeding the 700 pF HDMI limit. The IP4787CZ32 can
easily decouple this from the weaker ASIC I/O buffers, and drive the rogue cable
successfully.
(6'B%<3$66
,17B9
Nȍ
,17B9&&6<6
(6'B%<3$66
Nȍ
Nȍ
Nȍ
''&B'$7B6<6
''&B'$7B&21
''&B&/.B6<6
''&B&/.B&21
,17B9&&6<6
,17B9
DDD
DDD
a. DDC clock
b. DDC data
Fig 21. DDC circuit
5
(1)
4
V
3
2
(2)
1
0
time
018aaa105
(1) Valid I2C signaling example on the cable (connector side) from 5 V (HIGH) to approximately 1 V (LOW).
(2) Valid logic-level signaling example to the ASIC (system side) from 1.8 V (HIGH) to approximately 0.5 V (LOW).
Fig 22. DDC level shifting waveform example
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
21 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.5 CEC circuit
The logical multidrop topology of the CEC bus can include complex physical stubs,
loading cables, and interconnects that may deteriorate signal quality.
The IP4787CZ32 includes a full bidirectional buffer to drive the CEC bus and isolate
the CEC microcontroller or ASIC General-Purpose Input/Output (GPIO).
The CEC buffer derives power from an on-board 3.3 V regulator from the 5 V power
domain (see Figure 23). This allows extensive system power management configurations
and guarantees an HDMI-compliant V(CEC_CON) on the connector, as well as a
backdrive-protected 125 A nominal CEC pull-up which does not degrade the bus when
powered down.
By placing the CEC microcontroller and either VCC(5V0) or HDMI_5V_CON input on a 5 V
rail as shown in Figure 28, the CEC microcontroller can communicate over CEC for power
commands, and then enable the HDMI port via the ACTIVE pin, as well as the rest of the
system as needed.
(6'B%<3$66
,17B9
,17B9&&6<6
9
Nȍ
Nȍ
&(&B&21
&(&B6<6
DDD
Fig 23. CEC module
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
22 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.6 Logic low I2C voltage shifter
The DDC buffers provide an additional feature commonly required for high-integration
HDMI ASICs which are limited to CMOS or LVTTL LOW-level input voltage (VIL) on their
available I/O buffer cells. These I/Os are not strictly compliant with the 0.3 VDD threshold
voltage levels of I2C and may miss intended logic LOW levels on the cable between 0.8 V
and 1.5 V (typical values).
This feature is also included in the CEC buffer thus allowing standard I/O buffer cells to be
used in ASICs and microcontrollers connected to CEC_SYS.
DDD
9
9&&6<69
(1) VOL_CEC(max) maximum output voltage driven to system (ASIC) side when CEC is logic LOW
(2) VOL_DDC(max) maximum output voltage driven to system (ASIC) side when DDC is logic LOW
(3) VIL(max) maximum input voltage on system (ASIC) side to drive DDC or CEC logic LOW
(4) VIH(min) minimum input voltage on system (ASIC) side to drive DDC or CEC logic HIGH
Fig 24. Logic voltage thresholds as a function of supply voltage; on connector
(HDMI) side
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
23 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.7 Hot plug circuit
The IP4787CZ32 includes a hot plug drive circuit that simplifies the hot plug application. It
drives an HDMI-compliant hot plug signal to the HDMI sink. By design, the hot plug drive
circuit avoids glitches or short pulses on the hot plug line and is protected against
shortage to the 5 V input.
In order to signal a HIGH level on the HOTPLUG_CON output pin, the HOTPLUG_CTRL
input pin needs to be driven HIGH and a 5 V supply needs to be available on
HDMI_5V0_CON. Driving HOTPLUG_CTRL LOW generates a LOW-level output on the
HOTPLUG_CON pin. An integrated 100 k resistor on the HOTPLUG_CTRL pin prevents
from undefined (floating) state on HOTPLUG_CON.
In full accordance with the HDMI specification, the LOW and HIGH output levels
generated on the HOTPLUG_CON output always show a proper impedance of 1 k.
(6'B%<3$66
+'0,B9B&21
Nȍ
&21752/
%/2&.
+273/8*B&21
+273/8*B&75/
Nȍ
DDD
Fig 25. Hot plug circuit
9.8 HEAC support and utility pin
In addition to the ESD protection implemented at UTILITY_CON, IP4787CZ32 also
includes a biasing output for HEAC functionality. This output buffer is closely tied to the
output on the HOTPLUG_CON pin. A LOW-level output signal on HOTPLUG_CON also
causes a low output on UTILITY_CON and a HIGH level on HOTPLUG_CON results in an
identical high output on UTILITY_CON.
As for HOTPLUG_CON, the LOW and HIGH output levels generated on the
UTILITY_CON output always show an impedance of 1 k.
(6'B%<3$66
Nȍ
87,/,7<B&21
+'0,B9B&21
&21752/
%/2&.
+273/8*B&75/
Nȍ
DDD
Fig 26. Utility circuit
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
24 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.9 EDID programming using ENABLE_LDO
IP4787CZ32 has a special mode providing an internal 5 V supply to the connector side
power supply. This special mode allows programming of an Extended Display
Identification Data Programmable Read-Only Memory (EDID PROM) placed on DDC bus
between the device and the HDMI connector.
The EDID programming mode can be utilized by driving an active HIGH signal to the
ENABLE_LDO input pin. This enables an internal 5 V Low DropOut (LDO) to provide the
supply on VCC(5V0) to HDMI_5V0_CON pin in case no higher supply is available at this pin.
An active LOW input to ENABLE_LDO disables the EDID programming mode.
9.10 Backdrive protection
The HDMI connector contains various signals which can partly supply current into an
HDMI device that is powered down.
Typically, the DDC lines and the CEC signals can force significant current back into the
powered-down rails as shown in Figure 27, causing power-on reset problems with the
system, and possible damage. The IP4787CZ32 prevents this backdrive condition
whenever the I/O voltage is greater than the local supply.
supply off
5V
HDMI source
HDMI sink
backdrive current
HDMI ASIC
I2C-bus ASIC
018aaa109
Fig 27. Generalized backdrive protection
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
25 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.11 Schematic view of application
Only a single external component (CO = 1 F) is required to protect and interface the
ASIC to a complete and compliant HDMI port. The 100 nF ESD bypass capacitor is
optional.
&(&
—&
9WR96833/<
$&7,9(
&(&B6<6
9WR9
6833/<
(6'
E\SDVV
RSWLRQDO
9''
Q)
+'0,
&211(&725
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B'B6<6
70'6B'B&21
70'6B&.B6<6
70'6B&.B&21
70'6B&.B6<6
70'6B&.B&21
&(&B&21
,3&=
''&B&/.B6<6
''&B&/.B&21
''&B'$7B6<6
''&B'$7B&21
+273/8*B&75/
+273/8*B&21
(1$%/(B/'2
+'0,B9B&21
&2
+'0,
$6,&
—)
3$'
87,/,7<B&21
DDD
Fig 28. Schematic view of IP4787CZ32 application
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
26 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
9.12 Typical application
The IP4787CZ32 is designed to simplify routing to the HDMI connector, and ease the
incorporation of high-level ESD protection into delicately balanced high-speed
TMDS lines. These lines rely on tightly controlled microstrip or stripline transmission lines
with minimal impedance discontinuities, which can deteriorate return loss, increase
deterministic jitter and generally erode overall link signal integrity.
Normally, when designing a PCB with standard shunt ESD clamps, careful consideration
must be given to manual pre-compensation of the additional load of the added
ESD component. With the IP4787CZ32 TLCs, the ESD suppressor is designed to
maintain the characteristic impedance of the PCB microstrip or stripline. Therefore the
designer has to be concerned only with the standard-controlled impedance of the
unloaded PCB lines. This simplifies the task of the PCB designer, and minimizes the
tuning cycles, which are sometimes required when pre-compensation misses the mark.
A basic application diagram for the ESD protection of an HDMI interface is shown in
Figure 29 for a type-A HDMI connector.
The optimized HVQFN32 pinning simplifies the PCB design to keep the ESD protection
close to the connector where it can minimize the coupling of the ESD pulse onto other
lines in the system during a strike.
Due to the integrated pull-up and pull-down resistors, only two external capacitors are
required to implement a fully compliant HDMI port.
PP
DDD
Fig 29. Application of the IP4787CZ32 showing optimized HDMI type-A connector routing
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
27 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
10. Package outline
HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;
32 terminals; body 5 x 5 x 0.85 mm
D
B
SOT617-3
A
terminal 1
index area
A
A1
E
detail X
C
e1
e
9
y1 C
C A B
C
v
w
1/2 e b
y
16
L
17
8
e
e2
Eh
1/2 e
24
1
terminal 1
index area
32
25
X
Dh
0
2.5
Dimensions
Unit(1)
mm
5 mm
scale
A(1)
A1
b
max
0.05 0.30
nom 0.85
min
0.00 0.18
c
D(1)
Dh
E(1)
Eh
5.1
3.75
5.1
3.75
0.2
4.9
3.45
4.9
e
e1
e2
0.5
3.5
3.5
L
v
w
y
y1
0.5
0.1
0.05 0.05
0.1
0.3
3.45
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
Outline
version
SOT617-3
References
IEC
JEDEC
JEITA
sot617-3_po
European
projection
Issue date
11-06-14
11-06-21
MO-220
Fig 30. Package outline SOT617-3 (HVQFN32)
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
28 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
11.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
11.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
•
•
•
•
•
•
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
11.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
29 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
11.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 31) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 11 and 12
Table 11.
SnPb eutectic process (from J-STD-020D)
Package thickness (mm)
Package reflow temperature (C)
Volume (mm3)
< 350
 350
< 2.5
235
220
 2.5
220
220
Table 12.
Lead-free process (from J-STD-020D)
Package thickness (mm)
Package reflow temperature (C)
Volume (mm3)
< 350
350 to 2000
> 2000
< 1.6
260
260
260
1.6 to 2.5
260
250
245
> 2.5
250
245
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 31.
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
30 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
temperature
maximum peak temperature
= MSL limit, damage level
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 31. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
12. Glossary
HDMI sink — Device which receives HDMI signals for example, a TV set.
HDMI source — Device which transmits HDMI signal for example, DVD player.
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
31 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
13. Revision history
Table 13.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
IP4787CZ32 v.3
20141219
Product data sheet
-
IP4787CZ32 v.2
Modifications:
•
Added support for HDMI 2.0 display modes and updated ESD robustness
IP4787CZ32 v.2
20121220
Product data sheet
-
IP4787CZ32 v.1
IP4787CZ32 v.1
20120730
Preliminary data sheet
-
-
IP4787CZ32
IP4787CZ32
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
32 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
14. Legal information
14.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
IP4787CZ32
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
33 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
15. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
IP4787CZ32
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 19 December 2014
© NXP Semiconductors N.V. 2015. All rights reserved.
34 of 35
IP4787CZ32
NXP Semiconductors
DVI and HDMI interface ESD and overcurrent protection
16. Contents
1
1.1
1.2
1.3
2
2.1
2.2
3
4
5
6
7
8
8.1
8.2
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
9.12
10
11
11.1
11.2
11.3
11.4
12
13
14
14.1
14.2
14.3
14.4
15
16
Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General description . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ordering information . . . . . . . . . . . . . . . . . . . . . 4
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 5
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Static characteristics. . . . . . . . . . . . . . . . . . . . . 7
Dynamic characteristics . . . . . . . . . . . . . . . . . 11
AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . 17
DDC propagation delay . . . . . . . . . . . . . . . . . 17
DDC transition time . . . . . . . . . . . . . . . . . . . . 18
Application information. . . . . . . . . . . . . . . . . . 19
HDMI connector side ESD protection . . . . . . . 19
TMDS ESD protection concept. . . . . . . . . . . . 19
Operating and standby modes . . . . . . . . . . . . 20
DDC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CEC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Logic low I2C voltage shifter . . . . . . . . . . . . . . 23
Hot plug circuit . . . . . . . . . . . . . . . . . . . . . . . . 24
HEAC support and utility pin. . . . . . . . . . . . . . 24
EDID programming using ENABLE_LDO. . . . 25
Backdrive protection . . . . . . . . . . . . . . . . . . . . 25
Schematic view of application . . . . . . . . . . . . 26
Typical application . . . . . . . . . . . . . . . . . . . . . 27
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 28
Soldering of SMD packages . . . . . . . . . . . . . . 29
Introduction to soldering . . . . . . . . . . . . . . . . . 29
Wave and reflow soldering . . . . . . . . . . . . . . . 29
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 29
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 30
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 32
Legal information. . . . . . . . . . . . . . . . . . . . . . . 33
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 33
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Contact information. . . . . . . . . . . . . . . . . . . . . 34
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP Semiconductors N.V. 2015.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 19 December 2014
Document identifier: IP4787CZ32