HV QF N3 2 IP4788CZ32 DVI and HDMI interface ESD and overcurrent protection, DDC/CEC buffering, hot plug detect and backdrive protection Rev. 2 — 24 November 2014 Product data sheet 1. Product profile 1.1 General description The IP4788CZ32 is designed to protect High-Definition Multimedia Interface (HDMI) transmitter host interfaces. It includes HDMI 5 V overcurrent / overvoltage protection, Display Data Channel (DDC) buffering and decoupling, hot plug detect, backdrive protection, Consumer Electronic Control (CEC) buffering and decoupling, and 14 kV contact ElectroStatic Discharge (ESD) protection for all external I/Os, far exceeding the IEC 61000-4-2, level 4 standard. The IP4788CZ32 incorporates Transmission Line Clamping (TLC) technology on the high-speed Transition Minimized Differential Signaling (TMDS) lines to simplify routing and help reducing impedance discontinuities. All TMDS lines are protected by an impedance-matched diode configuration that minimizes impedance discontinuities caused by typical shunt diodes. The enhanced 60 mA overcurrent / overvoltage linear regulator guarantees HDMI-compliant 5 V output voltage levels with up to 6.5 V inputs. The DDC lines use a new buffering concept which decouples the internal capacitive load from the external capacitive load for use with standard Complementary Metal Oxide Semiconductor (CMOS) or Low Voltage Transistor-Transistor Logic (LVTTL) I/O cells down to 1.8 V. This buffering also redrives the DDC and CEC signals, allowing the use of longer or cheaper HDMI cables with a higher capacitance. The internal hot plug detect module simplifies the application of the HDMI transmitter to control the hot plug signal. All lines provide appropriate integrated pull-ups and pull-downs for HDMI compliance and backdrive protection to guarantee that HDMI interface signals are not pulled down when the system is powered down or enters Standby mode. Only a single external capacitor is required for operation. 1.2 Features and benefits HDMI 2.0 and all backward compatible standards are supported 6.0 Gbps TMDS Bit Rate (600 Mcsc TMDS Character Rate) compatible Supports Ultra High-Definition (UHD) 4K (2160p) 60 Hz display modes Impedance matched 100 differential transmission line ESD protection for TMDS lines (10 ). No Printed-Circuit Board (PCB) pre-compensation required Simplified flow-through routing utilizing less overall PCB space DDC capacitive decoupling between system side and HDMI connector side and buffering to drive cable with high capacitive load (> 700 pF/25 m) IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection All external I/O lines with ESD protection of at least 14 kV, exceeding the IEC 61000-4-2, level 4 standard Hot plug detect module CEC buffering and isolation, with integrated backdrive-protected 26 k pull-up Robust ESD protection without degradation after repeated ESD strikes Highest integration in a small footprint, PCB level, optimized RF routing, 32-pin HVQFN leadless package 1.3 Applications The IP4788CZ32 can be used for a wide range of HDMI source devices, consumer and computing electronics: High-Definition (HD) and Standard-Definition (SD) Blu-ray and DVD players Set-top box PC graphic card Game console HDMI picture performance quality enhancer module Digital Visual Interface (DVI) 2. Pinning information &(&B&21 9&&6<6 (6'B%<3$66 &(&B67%< &(&B6<6 QF WHUPLQDO LQGH[DUHD QF +273/8*B'(7B6<6 2.1 Pinning 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B6<6 70'6B'B6<6 70'6B'B&21 70'6B&.B6<6 70'6B&.B&21 70'6B&.B6<6 70'6B&.B&21 70'6B'B&21 87,/,7<B&21 70'6B'B&21 ''&B&/.B&21 ''&B'$7B&21 +'0,B9B&21 +273/8*B'(7B&21 9&&9 ''&B&/.B6<6 ''&B'$7B6<6 ,3&= DDD 7UDQVSDUHQWWRSYLHZ Fig 1. IP4788CZ32 IP4788CZ32 Pin configuration IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 2 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 2.2 Pin description Table 1. IP4788CZ32 IP4788CZ32 Pin description Pin Name Description 1 TMDS_D2+_SYS TMDS to ASIC inside system 2 TMDS_D2_SYS TMDS to ASIC inside system 3 TMDS_D1+_SYS TMDS to ASIC inside system 4 TMDS_D1_SYS TMDS to ASIC inside system 5 TMDS_D0+_SYS TMDS to ASIC inside system 6 TMDS_D0_SYS TMDS to ASIC inside system 7 TMDS_CK+_SYS TMDS to ASIC inside system 8 TMDS_CK_SYS TMDS to ASIC inside system 9 DDC_CLK_SYS DDC clock system side 10 DDC_DAT_SYS DDC data system side 5 V supply input 11 VCC(5V0) 12 HOTPLUG_DET_CON hot plug detect connector side 13 HDMI_5V0_CON 5 V overcurrent out to connector 14 DDC_DAT_CON DDC data connector side 15 DDC_CLK_CON DDC clock connector side 16 UTILITY_CON utility line ESD protection 17 TMDS_CK_CON TMDS ESD protection to connector 18 TMDS_CK+_CON TMDS ESD protection to connector 19 TMDS_D0_CON TMDS ESD protection to connector 20 TMDS_D0+_CON TMDS ESD protection to connector 21 TMDS_D1_CON TMDS ESD protection to connector 22 TMDS_D1+_CON TMDS ESD protection to connector 23 TMDS_D2_CON TMDS ESD protection to connector 24 TMDS_D2+_CON TMDS ESD protection to connector 25 CEC_CON CEC signal connector side 26 ESD_BYPASS ESD bias voltage 27 VCC(SYS) supply voltage for level shifting 28 CEC_STBY Standby mode control (LOW for lowest power, CEC-only mode) 29 CEC_SYS CEC I/O signal system side 30 n.c. not connected 31 n.c. not connected 32 HOTPLUG_DET_SYS hot plug detect system side ground pad GND ground All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 3 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 3. Ordering information Table 2. Ordering information Type number Package Name IP4788CZ32 IP4788CZ32 IP4788CZ32 Description Version DFN5050-32 plastic thermal enhanced very thin quad flat package; SOT617-3 (HVQFN32) no leads; 32 terminals; body 5 5 0.85 mm All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 4 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 4. Functional diagram 70'6B'B6<6 70'6B'B&21 (6' 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B&.B6<6 70'6B&.B&21 70'6B&.B6<6 70'6B&.B&21 9&&9 (6' 992/7$*( 5(*8/$725 9&&6<6 (6' &(&GULYHU Nȍ Nȍ &(&B6<6 &(&B&21 (6' 9&&6<6 +'0,B9B&21 (6' ''&GULYHU Nȍ Nȍ ''&B&/.B6<6 ''&B&/.B&21 9&&6<6 (6' +'0,B9B&21 (6' ''&GULYHU Nȍ Nȍ ''&B'$7B6<6 ''&B'$7B&21 +RWSOXJ (6' (6' +273/8*B'(7B6<6 +273/8*B'(7B&21 Nȍ Nȍ (6' (6' 9 &&9 +'0,B9B&21 (6' (6'B%<3$66 &855(17/,0,7(5 9&&6<6 PDLQ FODPS 9 &&9 (6' (6' HQDEOH HQ/LP HQ5HI 32:(5 0$1$*(0(1781,7 &(&B67%< HQ&(& 9&&6<6 9&&6<6 9 &&9 LELDVQ YUHIP &855(1792/7$*( 5()(5(1&(6 Fig 2. IP4788CZ32 IP4788CZ32 Nȍ (6' Q P 87,/,7<B&21 Nȍ DDD Functional diagram All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 5 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 5. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VCC(5V0) supply voltage (5.0 V) VI input voltage I/O pins VESD electrostatic discharge voltage IEC 61000-4-2, level 4 (contact) [1][2] - 14 kV IEC 61000-4-2, level 1 (contact) [3] - 2 kV DDC operating at 100 kHz; CEC operating at 1 kHz; 50 % duty cycle; CEC_STBY = HIGH; no current at HDMI_5V0_CON - 50 mW DDC and CEC bus in idle mode; CEC_STBY = HIGH; no current at HDMI_5V0_CON - 3.0 mW DDC and CEC bus in idle mode; CEC_STBY = LOW - 1.0 mW total power dissipation Ptot Conditions Min Max GND 0.5 6.5 GND 0.5 5.5 Unit V V Tamb ambient temperature 25 +85 C Tstg storage temperature 55 +125 C [1] Connector-side pins (typically denoted with “_CON” suffix) to ground. [2] Device is qualified with contact discharge pulses of ±14 kV according to the IEC 61000-4-2 model and far exceeds the specified level 4 (8 kV contact discharge). [3] System-side pins: CEC_SYS, DDC_DAT_SYS, DDC_CLK_SYS, HOTPLUG_DET_SYS, CEC_STBY, VCC(SYS) and VCC(5V0). IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 6 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 6. Static characteristics Table 4. Supplies Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter VCC(5V0) supply voltage (5.0 V) VCC(SYS) system supply voltage [1] Conditions [1] Min Typ Max Unit 4.5 5.0 6.5 V 1.62 3.3 5.5 V IP4788CZ32 contains a 5 V voltage regulator function for higher input voltages. Any input voltage of 4.925 V < VCC(5V0) < 6.50 V provides HDMI-compliant output levels of 4.8 V to 5.3 V on HDMI_5V0_CON. Table 5. TMDS protection circuit Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 90 100 110 - 0.6 - pF 6.0 - 9.0 V TMDS channel Zi(dif) differential input impedance effective capacitance Ceff TDR measured; tr = 200 ps equivalent shunt capacitance for TDR minimum; tr = 200 ps [1][2] Protection diode VBRzd Zener diode breakdown voltage I = 1.0 mA rdyn dynamic resistance TLP positive transient [3] - 0.5 - negative transient [3] - 0.4 - [4][5] - 0.1 1.0 A - 1.0 - A - 0.7 - V - 8.0 - V Ibck back current VCC(5V0) < Vch(TMDS) ILR reverse leakage current VI = 3.0 V VF forward voltage VCL(ch)trt(pos) positive transient channel clamping voltage [1] 100 ns TLP; 50 pulser at 50 ns This parameter is guaranteed by design. [2] Capacitive dip at HDMI Time Domain Reflectometer (TDR) measurement conditions. [3] ANSI-ESDSP5.5.1-2004, ESD sensitivity testing Transmission Line Pulse (TLP) component level method 50 TDR. [4] Signal pins: TMDS_D0+_CON, TMDS_D0_CON, TMDS_D1+_CON, TMDS_D1_CON, TMDS_D2+_CON, TMDS_D2_CON, TMDS_CK+_CON, TMDS_CK_CON, TMDS_D0+_SYS, TMDS_D0_SYS, TMDS_D1+_SYS, TMDS_D1_SYS, TMDS_D2+_SYS, TMDS_D2_SYS, TMDS_CK+_SYS and TMDS_CK_SYS. [5] Backdrive current from TMDS_x_SYS and TMDS_x_CON pins to local VCC(5V0) bias rail at power-down. Device does not block backdrive current leakage through the device to/from ASIC I/O pins connected to TMDS_x_SYS pins. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 7 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 6. HDMI_5V0_CON Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions rdyn dynamic resistance TLP Min Typ Max Unit positive transient [1] - 1.0 - negative transient [1] - 1.0 - VCL clamping voltage 100 ns TLP; 50 pulser at 50 ns - 8 - V IO(max) maximum output current V(HDMI_5V0_CON) = 4.8 V 55 - - mA Ibck back current VCC(5V0) < V(HDMI_5V0_CON) - - 10 A IO(sc) short-circuit output current V(HDMI_5V0_CON) = 0 V - 125 175 mA IO = 10 mA - 70 - mV IO = 55 mA - - 125 mV 4.8 5.05 5.3 V dropout voltage Vdo VO(LDO) LDO output voltage 4.5 V < VCC(5V0) < 4.925 V; DDC = LOW IO 55 mA; 4.925 V < VCC(5V0) < 6.5 V; DDC = LOW [2] [2] [1] ANSI-ESDSP5.5.1-2004, ESD sensitivity testing TLP component level method 50 TDR. [2] IP4788CZ32 contains a 5 V voltage regulator function for higher input voltages. Any input voltage of 4.925 V < VCC(5V0) < 6.50 V provides HDMI-compliant output levels of 4.8 V to 5.3 V on HDMI_5V0_CON. Table 7. UTILITY_CON Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit - Supplies: pins VCC(5V0) and VCC(SYS) rdyn dynamic resistance TLP positive transient [1] - 1.0 negative transient [1] - 1.0 - VCL clamping voltage 100 ns TLP; 50 pulser at 50 ns - 8.0 - V Ci input capacitance VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz, - 8.0 10 pF Rpd pull-down resistance 60 100 140 k [1] ANSI-ESDSP5.5.1-2004, ESD sensitivity testing TLP component level method 50 TDR. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 8 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 8. Static characteristics Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions DDC buffer on connector Min Typ Max Unit V side[1] VIH HIGH-level input voltage 0.5 V(HDMI_5V0_CON) 6.5 VIL LOW-level input voltage 0.5 - 0.3 V V(HDMI_5V0_CON) VOH HIGH-level output voltage V(HDMI_5V0_CON) 0.02 V(HDMI_5V0_CON) V + 0.02 VOL LOW-level output voltage internal pull-up and external sink - 100 200 mV VIK input clamping voltage II = 18 mA - - 1.0 V - 8.0 10 pF 1.6 1.8 2.0 k VCC(SYS) = 1.8 V 450 - - mV VCC(SYS) = 2.5 V 620 - - mV VCC(SYS) = 3.3 V 760 - - mV VCC(SYS) = 5.0 V 800 - - mV VCC(SYS) = 1.8 V - - 330 mV VCC(SYS) = 2.5 V - - 380 mV VCC(SYS) = 3.3 V - - 400 mV - - 420 mV CIO input/output capacitance Rpu pull-up resistance DDC buffer on system VIH VIL [2] VCC(5V0) = 5.0 V; VCC(SYS) = 3.3 V; CEC_STBY = HIGH [2][3] side[1][4] HIGH-level input voltage LOW-level input voltage VCC(SYS) = 5.0 V VOH HIGH-level output voltage VOL LOW-level output voltage VCC(SYS) 0.02 - VCC(SYS) + 0.02 V VCC(SYS) = 1.8 V - 490 500 mV VCC(SYS) = 2.5 V - 640 700 mV VCC(SYS) = 3.3 V - 685 790 mV VCC(SYS) = 5.0 V - 720 830 mV [2] VIK input clamping voltage II = 18 mA CIO input/output capacitance VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz Rpu pull-up resistance IP4788CZ32 IP4788CZ32 [2] - - 1.0 V - 6.0 8.0 pF 3.2 3.65 4.1 k All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 9 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 8. Static characteristics …continued Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit - - V CEC_CON[1] VIH HIGH-level input voltage 2.0 VIL LOW-level input voltage - - 0.80 V VOH HIGH-level output voltage 2.88 3.3 3.63 V VOL LOW-level output voltage - 100 200 mV - 8.0 10 pF CIO input/output capacitance Rpu pull-up resistance IL(CEC_CON) leakage current on pin CEC_CON IOL = 1.5 mA VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz [2] 23.4 26.0 28.6 k VCC(5V0) = 0 V; VCC(SYS) = 0 V; CEC_CON connected to 3.63 V via 27 k - - 0.1 A VCC(SYS) = 1.8 V 450 - - mV VCC(SYS) = 2.5 V 620 - - mV VCC(SYS) = 3.3 V 760 - - mV VCC(SYS) = 5.0 V 800 - - mV VCC(SYS) = 1.8 V - - 330 mV VCC(SYS) = 2.5 V - - 380 mV VCC(SYS) = 3.3 V - - 400 mV VCC(SYS) = 5.0 V - - 420 mV CEC_SYS[1][4] VIH VIL HIGH-level input voltage LOW-level input voltage VOH HIGH-level output voltage VOL LOW-level output voltage VCC(SYS) 0.02 - VCC(SYS) + 0.02 V VCC(SYS) = 1.8 V - 490 500 mV VCC(SYS) = 2.5 V - 640 690 mV VCC(SYS) = 3.3 V - 675 770 mV - 710 800 mV - 6.0 7.0 pF 8.5 10 11.5 k [2] VCC(SYS) = 5.0 V CIO input/output capacitance Rpu pull-up resistance VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz [2] HOTPLUG_DET_CON[1] VIH HIGH-level input voltage 2.0 - - V VIL LOW-level input voltage - - 0.8 V Rpd pull-down resistance 60 100 140 k Ci input capacitance - 8.0 10 pF IP4788CZ32 IP4788CZ32 VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz [2] All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 10 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 8. Static characteristics …continued Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 0.7 VCC(SYS) - - V HOTPLUG_DET_SYS[1] VOH HIGH-level output voltage IOL = 1 mA VOL LOW-level output voltage Rpd pull-down resistance [1] IOL = 1 mA - 200 300 mV 60 100 140 k The device is active if the input voltage at pin CEC_STBY is above the HIGH level. [2] This parameter is guaranteed by design. [3] Capacitive load measured at power-on. [4] No external pull-up resistor attached. Table 9. CEC_STBY power management circuit VCC(SYS) = 1.62 V to 5.5 V; VCC(5V0) = 4.5 V to 6.5 V; GND = 0 V; Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Board side: input pin CEC_STBY[1] VIH HIGH-level input voltage VIL LOW-level input voltage Rpd pull-down resistance Ci input capacitance [1] HIGH = active [2] 1.2 - 6.5 V LOW = standby [3] 0.5 - 0.8 V 60 100 140 k - 6 7 pF VI = 3 V or 0 V The CEC_STBY pin should be connected permanently to VCC(5V0) or VCC(SYS) if no enable control is needed. [2] DDC buffers, Hot Plug Detect (HPD) buffer, and HDMI_5V0_CON out enabled; CEC buffer enabled. [3] DDC buffers, HPD buffer, and HDMI_5V0_CON out disabled; CEC buffer enabled. 7. Dynamic characteristics Table 10. Dynamic characteristics VCC(5V0) = 5.0 V; VCC(SYS) = 1.8 V; GND = 0 V; Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions DDC_DAT_SYS, DDC_CLK_SYS, DDC_DAT_CON, Min Typ Max Unit DDC_CLK_CON[1] tPLH LOW to HIGH propagation delay system side to connector side Figure 11 - 80 - ns tPHL HIGH to LOW propagation delay system side to connector side Figure 11 - 60 - ns tPLH LOW to HIGH propagation delay connector side to system side Figure 12 - 120 - ns tPHL HIGH to LOW propagation delay connector side to system side Figure 12 - 80 - ns tTLH LOW to HIGH transition time connector side Figure 13 - 150 - ns tTHL HIGH to LOW transition time connector side Figure 13 - 100 - ns tTLH LOW to HIGH transition time system side Figure 14 - 250 - ns tTHL HIGH to LOW transition time system side Figure 14 - 80 - ns [1] All dynamic measurements are done with a 75 pF load. Rise times are determined by internal pull-up resistors. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 11 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection DDD =GLI ȍ 70'6B&/. 70'6B' 70'6B' 70'6B' WLPHQV tr = 200 ps; no filter; VCC(5V0) = 5 V 100 differential (CH1 + CH2) Fig 3. Differential TDR plot DDD 227 MHz pixel clock Horizontal scale: 90 ps/div Vertical scale: 200 mV/div Offset: 42.6 mV Fig 4. IP4788CZ32 IP4788CZ32 Eye diagram using IP4788CZ32 (1080p, 12 bit) All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 12 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection DDD 297 MHz pixel clock Horizontal scale: 67.5 ps/div Vertical scale: 200 mV/div Offset: 42.6 mV Fig 5. Eye diagram using IP4788CZ32 (1080p, 16 bit) aaa-015846 148 MHz test frequency Horizontal scale: 34 ps/div Vertical scale: 200 mV/div Measured at TP2 with worst cable emulator, reference cable equalizer and worst case positive skew. Fig 6. IP4788CZ32 IP4788CZ32 Eye diagram using IP4788CZ32 (2160p, 60 Hz) All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 13 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection DDD , $ , $ 9&/9 tp = 100 ns; TLP; TMDS pins Fig 7. DDD 9&/9 tp = 100 ns; TLP; TMDS pins Dynamic resistance with positive clamping 018aaa095 6.5 VI (V) Fig 8. Dynamic resistance with negative clamping 018aaa096 6.0 VO (V) 6.0 (2) (5) (4) (1) 4.0 5.5 (1) 2.0 (3) 5.0 (4) (3) (2) 4.5 5.0 5.5 6.0 6.5 0.0 0.00 0.02 0.04 VCC(5V0) (V) (1) 5.3 V; maximum values; HDMI CTS TID 7-11 (1) VCC(5V0) = 4.5 V (2) 4.8 V; minimum values; HDMI CTS TID 7-11 (2) VCC(5V0) = 5.0 V (3) I = 0 mA (3) VCC(5V0) = 5.5 V (4) I = 55 mA (4) VCC(5V0) = 6.5 V 0.06 0.08 0.10 0.12 IO (A) 0.14 (5) VCC(5V0) supply input; 4.925 V to 6.5 V Fig 9. Overvoltage limiter function (HDMI_5V0_CON) IP4788CZ32 IP4788CZ32 Fig 10. Overcurrent limiter function (HDMI_5V0_CON) All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 14 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 8. AC waveforms 8.1 DDC propagation delay VCC(SYS) DDC system side 0.5 VCC(SYS) 0.28 VCC(SYS) VOL V(HDMI_5V0_CON) DDC connector side 0.5 V(HDMI_5V0_CON) 0.5 V(HDMI_5V0_CON) VOL tPHL tPLH 018aaa097 Fig 11. Propagation delay DDC, DDC system side to DDC connector side V(HDMI_5V0_CON) DDC connector side 0.5 V(HDMI_5V0_CON) 0.5 V(HDMI_5V0_CON) VOL VCC(SYS) DDC system side 0.5 VCC(SYS) 0.5 VCC(SYS) VOL tPHL tPLH 018aaa098 Fig 12. Propagation delay DDC, DDC connector side to DDC system side IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 15 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 8.2 DDC transition time DDC system side VCC(SYS) VOL V(HDMI_5V0_CON) DDC connector side 80 % V(HDMI_5V0_CON) 20 % V(HDMI_5V0_CON) VOL tPHL tPLH 018aaa099 Fig 13. Transition time DDC connector side V(HDMI_5V0_CON) DDC connector side VOL VCC(SYS) DDC system side 80 % VCC(SYS) 20 % VCC(SYS) VOL tPHL tPLH 018aaa100 Fig 14. Transition time DDC system side IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 16 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9. Application information 9.1 HDMI connector side ESD protection All pins directly interfacing with the HDMI connector provide up to 14 kV contact ESD protection according to IEC 61000-4-2, exceeding level 4. In order to utilize the full scope of this protection, connect all connector side pins to the HDMI connector. 9.2 TMDS ESD To protect the TMDS lines and also to comply with the impedance requirements of the HDMI specification, IP4788CZ32 provides ESD protection with matched TLC ESD structures. Typical Dual Rail Clamp (DRC) or rail-to-rail shunt structures are common for low-capacitance ESD protection (as shown on the left side of Figure 15) where the dominant factor for the TMDS line impedance dip is determined by the capacitive load to ground. Parasitic lead inductances of the packaging in this case work against the ESD clamping performance by including the I/t reactance of the inductance into the path of the ESD shunt. In order to present an effective capacitive load of roughly only 0.7 pF, IP4788CZ32 utilizes these inherent inductances in series with the transmission line. This TLC structure minimizes the capacitive dip, for ideal signal integrity (Figure 15; right side) without complicated PCB pre-compensation. As a beneficial side effect, this structure enhances the ESD performance of the device as well. The reactance of the series inductance attenuates the fast initial peak of the ESD pulse for a lower residual pulse delivered to the Application Specific Integrated Circuit (ASIC). 018aaa102 018aaa101 a. Classic parallel ESD shunt protection b. Improved series shunt TLC clamping Fig 15. TLC ESD protection of TMDS lines IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 17 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.3 Operating and standby modes The operating mode of IP4788CZ32 depends on the availability of the VCC(5V0) and VCC(SYS) supply voltages and on the state of the CEC_STBY input signal. Without availability of both supplies, IP4788CZ32 is in Standby mode. As soon as VCC(5V0) and VCC(SYS) are within the range specified in Section 6, the part is in an operating mode that can be controlled via the CEC_STBY input signal. In case CEC_STBY is LOW, only the CEC buffer is active and enabled to receive or send CEC commands. All other outputs are in a high-ohmic state. A HIGH input signal enables all parts of IP4788CZ32 and puts the device into full operating mode. Table 11. Operating modes VCC(SYS) VCC(5V0) CEC_STBY[1] Mode Description < 1.1 V < 4.5 V X Standby mode all outputs high-ohmic 1.1 V 4.5 V L CEC Standby mode CEC circuit active; all other outputs high-ohmic H full operating mode all functional blocks active [1] X = Don’t care (either LOW or HIGH level); L = LOW-level input; H = HIGH-level input If no CEC Standby mode is required, or if no special Power-down modes are desired, the CEC_STBY pin can be pulled HIGH to VCC(5V0) or VCC(SYS) for continuous HDMI and CEC operation as soon as the supplies are available. Strapping the CEC_STBY = VCC(SYS) = VDD of ASIC guarantees that all interface signals ending with the suffix “_SYS” on the system side are disabled when VCC(SYS) goes LOW. This configuration protects the ASIC I/O signals from exceeding its local VDD. In this mode, even if VCC(5V0) is powered, HDMI_5V0_CON goes active and hot plug events can be detected only when the ASIC power supply rail is on. Strapping CEC_STBY = VCC(5V0) is the most basic configuration where the buffers are enabled whenever the local VCC(5V0) and VCC(SYS) supplies reach minimum operating levels. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 18 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.4 DDC circuit The DDC bus circuit integrates all required pull-ups, and provides full capacitive decoupling between the HDMI connector and the DDC bus lines on the PCB. The capacitive decoupling ensures that the maximum capacitive load is well within the 50 pF maximum of the HDMI specification. No external pull-ups or pull-downs are required. The bidirectional buffers support high-capacitive load on the HDMI cable-side. Various non-compliant but prevalent low-cost cables have been observed. They have a capacitive load of up to 6 nF on the DDC lines, far exceeding the 700 pF HDMI limit. IP4788CZ32 can easily decouple this from the weaker ASIC I/O buffers, and drive the rogue cable successfully. ESD_BYPASS HDMI_5V0_CON 1.85 kΩ ESD_BYPASS VCC(SYS) VCC(SYS) 1.85 kΩ 3.65 kΩ 3.65 kΩ DDC_DAT_SYS DDC_DAT_CON DDC_CLK_SYS DDC_CLK_CON HDMI_5V0_CON 018aaa103 018aaa104 a. DDC clock b. DDC data Fig 16. DDC circuit 5 (1) 4 V 3 2 (2) 1 0 time 018aaa105 (1) Valid I2C signaling example on the cable (connector side) from 5 V (HIGH) to approximately 1 V (LOW). (2) Valid logic-level signaling example to the ASIC (system side) from 1.8 V (HIGH) to approximately 0.5 V (LOW). Fig 17. DDC level shifting waveform example IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 19 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.5 Logic low I2C voltage shifter The DDC buffers provide an additional feature commonly required for high-integration HDMI ASICs. In order to be compatible with the 5 V I2C standard used for DDC communication, I/O buffer cells of many HDMI modern transmitter chips require level shifting. As FET-based level shifting just limits the high level of the signal, the low level remains unchanged. As a result, the low-level voltages on the DDC bus often exceed the 0.3 VDD LOW-level input voltage (VIL) limit of low-voltage I/O buffers. To enable proper operation that is independent of the system side I/O voltage, the DDC buffers inside IP4788CZ32 shift both the high and the low levels by the required amount. This ensures that low levels on the system side DDC bus match the low-level input voltage requirements down to I/O voltages of 1.8 V. Besides the DDC buffers, this feature is also included in the CEC buffer, allowing standard I/O buffer cells to be used in HDMI ASICs and microcontrollers. 018aaa106 0.9 (1) VOL;VIH; VIL (V) (2) 0.7 (3) 0.5 0.3 1.6 2.6 3.6 4.6 5.6 VCC(SYS) (V) (1) VOL(max) driven to system (ASIC) side when I2C logic low (less than 0.3 HDMI_5V0_CON) (2) VIH(min) threshold on system (ASIC) side to drive I2C logic low (3) VIL(max) threshold on system (ASIC) side to drive I2C logic low Fig 18. Logic voltage thresholds as a function of supply voltage; on connector (HDMI) side IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 20 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.6 Hot plug detect circuit and HEAC support IP4788CZ32 includes a hot plug detect circuit which simplifies the hot plug application. The circuit generates a standard logic level from the hot plug signal. The hot plug detect circuit is pulling down the signal to avoid any floating signal. The comparator guarantees a save detection of the 2 V hot plug signal without any glitches or oscillation at the hot plug output. IP4788CZ32 also provides an additional ESD pin to protect the reserved / HEAC pin along with hot plug detect to 14 kV IEC 61000-4-2. ESD_BYPASS VCC(5V0) HOTPLUG_DET_CON HOTPLUG_DET_SYS 100 kΩ 100 kΩ 018aaa107 Fig 19. Hot plug detect circuit 9.7 CEC The logical multidrop topology of the CEC bus can include complex physical stubs, loading cables, and interconnects which may deteriorate signal quality. The IP4788CZ32 includes a full bidirectional buffer to drive the CEC bus and isolate the CEC microcontroller or ASIC General-Purpose Input/Output (GPIO). The CEC buffer derives power from an on-board 3.3 V regulator from the VCC(5V0) domain (see Figure 20). This deviation allows extensive system power management configurations and guarantees an HDMI-compliant V(CEC_CON) on the connector. It also allows a backdrive-protected 125 A nominal CEC pull-up which does not degrade the bus when powered down. By placing the CEC microcontroller and VCC(5V0) input on a 5 V rail as shown in Figure 23, the CEC microcontroller can communicate over CEC for power commands. It can then enable the HDMI port via the CEC_STBY pin, as well as the rest of the system as needed. The CEC buffer is always active as soon as both supply voltages are present. For details on the operating and Standby modes of IP4788CZ32, see Section 9.3. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 21 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection (6'B%<3$66 9&&9 9&&6<6 9 Nȍ Nȍ &(&B&21 &(&B6<6 DDD Fig 20. CEC module 9.8 Backdrive protection The HDMI connector contains various signals which can partly supply current into an HDMI device which is powered down. Typically, the DDC lines and the CEC signals can force significant current back into the powered-down rails as shown in Figure 21, causing power-on reset problems with the system, and possible damage. The IP4788CZ32 prevents this backdrive condition whenever the I/O voltage is greater than the local supply. VXSSO\RII 9 +'0,VRXUFH +'0,VLQN EDFNGULYHFXUUHQW +'0,$6,& ,&EXV$6,& DDD Fig 21. Generalized backdrive protection IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 22 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.9 55 mA overcurrent / overvoltage LDO function To isolate faults from the source power supply while still meeting HDMI output specifications, IP4788CZ32 integrates a complete linear output overcurrent protection. The Low DropOut (LDO) design provides a low-cost solution requiring just a single output capacitor (1 F or higher, Equivalent Series Resistance (ESR) < 1 ), eliminating start-up and ripple concerns (see Figure 22). A typical 100 mV Vdo overcurrent-only solution would require a 5.1 V 3 % input supply to guarantee 4.8 V to 5.3 V over 0 mA to 55 mA at the HDMI connector. The overcurrent / overvoltage feature of IP4788CZ32 allows the use of wider tolerance input supplies up to 6.5 V while still meeting the 4.8 V-to-5.3 V output limit required by HDMI. So, for example, a cost-reduced 5.2 V 5 % or even a 5.5 V 10 % supply can be used with the IP4788CZ32. As with all the I/O pins, this block is ESD-protected and also provides backdrive protection when a rogue HDMI sink powers the HDMI cable unexpectedly. ESD_BYPASS VCC(5V0) CEC 3V3 regulator HDMI_5V0_CON 60 mA overcurrent control DDC/HPD buffers CEC buffer 018aaa110 Fig 22. 5 V LDO with overcurrent / overvoltage protection IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 23 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.10 Schematic view of application Only a single external component (CO = 1 F) is required to protect and interface the ASIC to a complete and compliant HDMI port. The 100 nF ESD bypass capacitor is optional. &(& & 9WR96833/< &(&B67%< &(&B6<6 9WR9 6833/< (6' E\SDVV RSWLRQDO 9'' Q) +'0, &211(&725 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B&.B6<6 70'6B&.B&21 70'6B&.B6<6 70'6B&.B&21 &(&B&21 ,3&= ''&B&/.B6<6 ''&B&/.B&21 ''&B'$7B6<6 ''&B'$7B&21 +273/8*B'(7B6<6 +273/8*B'(7B&21 +'0, $6,& 3$' +'0,B9B&21 &2 ) 87,/,7<B&21 DDD Fig 23. Schematic view of IP4788CZ32 application IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 24 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.11 Typical application The IP4788CZ32 is designed to simplify routing to the HDMI connector and to ease the incorporation of high-level ESD protection into delicately balanced high-speed TMDS lines. These lines rely on tightly controlled microstrip or stripline transmission lines with minimal impedance discontinuities. They can deteriorate return loss, increase deterministic jitter and generally erode overall link signal integrity. Normally when designing the PCB with standard shunt ESD clamps, careful consideration must be given to manual pre-compensation of the additional load of the added ESD component. With the IP4788CZ32 TLCs, the ESD suppressor is designed to maintain the characteristic impedance of the PCB microstrip or stripline. Therefore the designer needs only to be concerned with the standard-controlled impedance of the unloaded PCB lines. This feature simplifies the task of the PCB designer, and minimizes the tuning cycles, which are sometimes required when pre-compensation misses the mark. A basic application diagram for the ESD protection of an HDMI interface is shown in Figure 24 for a type-A HDMI connector. The optimized DFN5050-32 pinning simplifies the PCB design to keep the ESD protection close to the connector where it can minimize the coupling of the ESD pulse onto other lines in the system during a strike. Due to the integrated pull-up and pull-down resistors, only two external capacitors are required to implement a fully compliant HDMI port. 001aan367 Fig 24. Application of the IP4788CZ32 showing optimized single-layer HDMI type-A connector routing IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 25 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 10. Package outline HVQFN32: plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body 5 x 5 x 0.85 mm D B SOT617-3 A terminal 1 index area A A1 E detail X C e1 e 9 y1 C C A B C v w 1/2 e b y 16 L 17 8 e e2 Eh 1/2 e 24 1 terminal 1 index area 32 25 X Dh 0 2.5 Dimensions Unit(1) mm 5 mm scale A(1) A1 b max 0.05 0.30 nom 0.85 min 0.00 0.18 c D(1) Dh E(1) Eh 5.1 3.75 5.1 3.75 0.2 4.9 3.45 4.9 e e1 e2 0.5 3.5 3.5 L v w y y1 0.5 0.1 0.05 0.05 0.1 0.3 3.45 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. Outline version SOT617-3 References IEC JEDEC JEITA sot617-3_po European projection Issue date 11-06-14 11-06-21 MO-220 Fig 25. Package outline DFN5050-32 (SOT617-3/HVQFN32) IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 26 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 11. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 11.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 11.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 11.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 27 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 11.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 26) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 12 and 13 Table 12. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 13. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 26. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 28 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 26. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 12. Glossary HDMI sink — Device which receives HDMI signals for example, a TV set. HDMI source — Device which transmits HDMI signal for example, DVD player. IP4788CZ32 IP4788CZ32 All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 29 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 13. Revision history Table 14. Revision history Document ID Release date Data sheet status Change notice Supersedes IP4788CZ32 v.2 20141124 Product data sheet - IP4788CZ32 v.1 Modifications: IP4788CZ32 v.1 IP4788CZ32 IP4788CZ32 • • • • • • • Editorial updates Section 1 “Product profile”: updated Figure 2 “Functional diagram”: updated Table 3 “Limiting values”: VESD value corrected Table 8 “Static characteristics”: added parameter leakage current on pin CEC_CON Figure 6: added Section 14 “Legal information”: updated 20130308 Product data sheet - All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 - © NXP Semiconductors N.V. 2014. All rights reserved. 30 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 14. Legal information 14.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 14.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. IP4788CZ32 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 31 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] IP4788CZ32 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 24 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 32 of 33 IP4788CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 16. Contents 1 1.1 1.2 1.3 2 2.1 2.2 3 4 5 6 7 8 8.1 8.2 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 10 11 11.1 11.2 11.3 11.4 12 13 14 14.1 14.2 14.3 14.4 15 16 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 4 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . 11 AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . 15 DDC propagation delay . . . . . . . . . . . . . . . . . 15 DDC transition time . . . . . . . . . . . . . . . . . . . . 16 Application information. . . . . . . . . . . . . . . . . . 17 HDMI connector side ESD protection . . . . . . . 17 TMDS ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Operating and standby modes . . . . . . . . . . . . 18 DDC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Logic low I2C voltage shifter . . . . . . . . . . . . . . 20 Hot plug detect circuit and HEAC support . . . 21 CEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Backdrive protection . . . . . . . . . . . . . . . . . . . . 22 55 mA overcurrent / overvoltage LDO function 23 Schematic view of application . . . . . . . . . . . . 24 Typical application . . . . . . . . . . . . . . . . . . . . . 25 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 26 Soldering of SMD packages . . . . . . . . . . . . . . 27 Introduction to soldering . . . . . . . . . . . . . . . . . 27 Wave and reflow soldering . . . . . . . . . . . . . . . 27 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 27 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 28 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 30 Legal information. . . . . . . . . . . . . . . . . . . . . . . 31 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 31 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Contact information. . . . . . . . . . . . . . . . . . . . . 32 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 24 November 2014 Document identifier: IP4788CZ32