PC www.vishay.com Vishay Dale Inductors, Subminiature, Shielded, Radial Leaded FEATURES ELECTRICAL SPECIFICATIONS Inductance Tolerance: ± 10 % Dielectric Strength: 840 VRMS at sea level Working Voltage: 300 VDC Q and SRF Values: Minimum not less than 80 % of specified value Maximum Current: Based on temperature rise not to exceed 35 °C at + 90 °C ambient • Classification is grade 1, class B • Subminiature shielded • Custom values up to 100 000 μH are available upon request • Printed board mounting facilitated by 0.200" [5.08 mm] grid spacing • Radial lead fixed inductor • High Q values • Unitized epoxy-molded construction • Shielded construction to allow maximum density packaging • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 DENSITY SPECIFICATIONS Weight: 1.5 g maximum Shielding: 3 % coupling maximum when two units are tested side by side ENVIRONMENTAL SPECIFICATIONS Moisture: Per MIL-STD-202, method 106 Vibration: Low frequency, 10 Hz to 55 Hz at 0.06" [1.52 mm] maximum total excursion at rate of 1 linear sweep per minute for 2 h repeated for each of three mutually perpendicular planes Shock: 100 g, 6 ms, body mounted MECHANICAL SPECIFICATIONS Operating Temperature: - 55 °C to + 125 °C Terminal Pull: 3 pounds DIMENSIONS in inches [millimeters] 0.300 ± 0.010 [7.62 ± 0.254] 0.265 ± 0.010 [6.73 ± 0.254] Dia. 0.270 [6.86] Max. 0.080 ± 0.010 [2.03 ± 0.254] 3/8 ± 1/16 [9.52 ± 1.59] #24 0.020 ± 0.002 [0.508 ± 0.051] TCW 0.200 ± 0.005 [5.08 ± 0.127] STANDARD ELECTRICAL SPECIFICATIONS IND. (μH) 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 TOL. (%) ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 Q NOM. 70 70 70 70 70 80 80 80 80 TEST FREQ. (MHz) 25 25 25 25 25 25 25 25 25 SRF NOM. (MHz) > 250 > 250 > 250 > 250 > 250 > 250 > 250 250 230 DCR MAX. () 0.030 0.030 0.030 0.035 0.038 0.040 0.040 0.045 0.045 RATED DC CURRENT (mA) 2500 2500 2500 2400 2300 2200 2200 2100 2100 MODEL PC PC PC PC PC PC PC PC PC Note (1) Incremental current: The DC current required to cause a 5 % reduction in the nominal inductance value. Revision: 05-Jun-13 INCREMENTAL CURRENT (mA) (1) 2500 2500 2500 2400 2300 2200 2200 2100 2100 Document Number: 34070 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PC www.vishay.com Vishay Dale STANDARD ELECTRICAL SPECIFICATIONS IND. (μH) 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 TOL. (%) ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 TEST FREQ. (MHz) 25 25 25 25 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 7.9 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 0.79 0.79 0.79 0.79 0.79 0.79 0.79 0.79 0.79 0.79 0.79 0.79 Q NOM. 80 80 85 85 90 100 115 110 110 90 90 95 95 85 95 90 120 120 115 125 115 120 120 110 115 105 105 95 95 90 95 95 100 100 100 100 95 100 90 100 SRF NOM. (MHz) 220 190 180 160 170 155 135 120 104 93 87 79 72 63 60 54 37 28.8 23.8 21.3 20.6 18.6 17.7 14.9 13.9 12.9 11.7 10.5 5.6 5.2 4.9 4.6 4.2 3.55 3.45 3.2 2.9 2.7 2.5 2.35 DCR MAX. () 0.050 0.055 0.060 0.070 0.085 0.100 0.110 0.120 0.125 0.165 0.180 0.245 0.265 0.330 0.460 0.640 0.800 0.865 0.940 1.03 1.18 1.30 1.41 1.61 2.08 2.20 2.42 2.15 2.38 2.52 2.88 3.18 3.50 4.80 5.44 5.9 6.3 7.2 8.0 12 RATED DC CURRENT (mA) 2000 1900 1800 1700 1670 1540 1470 1410 1380 1200 1135 985 950 853 720 620 545 520 504 460 418 398 385 350 330 320 300 333 316 306 288 273 260 222 209 201 194 181 172 141 MODEL PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC Note (1) Incremental current: The DC current required to cause a 5 % reduction in the nominal inductance value. INCREMENTAL CURRENT (mA) (1) 2000 1900 1800 1700 1670 1540 1470 1410 1380 1200 1135 985 950 853 720 620 545 520 504 460 418 398 385 350 333 330 320 300 190 175 150 125 120 110 105 100 90 80 70 65 MARKING - Manufacturer data printed ORDERING INFORMATION PC 0.10 μH 10 % EB e2 MODEL INDUCTANCE VALUE INDUCTANCE TOLERANCE PACKAGE CODE JEDEC LEAD (Pb)-FREE STANDARD GLOBAL PART NUMBER P C MODEL Revision: 05-Jun-13 9 E B PACKAGE CODE R 1 INDUCTANCE VALUE 0 K INDUCTANCE TOLERANCE Document Number: 34070 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000