Dimensions ● SXG (C-Mount version) Product Specification SXG cameras – Maximum Performance with Kodak sensors UNC 1/4-20 Color SXG10c SXG20c SXG21c SXG40c SXG80c Latest software version and technical documentation are available at: [max. fps] 1/2" 2/3" 2/3” 1” 4/3” 1024 x 1024 1600 x 1200 1920 x 1080 2336 x 1752 3296 x 2472 120 68 64 32 16 1/2” 2/3” 2/3” 1” 4/3” 1024 x 1024 1600 x 1200 1920 x 1080 2336 x 1752 3296 x 2472 120 68 64 32 16 36 26 Full Frames 72 52 36 26 Quick Start Guide SXG cameras (Gigabit Ethernet) Resolution Size 16 x M3 depth 6 52 Monochrome SXG10 SXG20 SXG21 SXG40 SXG80 Sensor 36 26 ▪▪ Dual Gigabit Ethernet progressive scan CCD camera ▪▪ Compact and lightweight aluminium housing ▪▪ Power over Ethernet support ▪▪ Standard RJ45 connector ▪▪ GigE VisionTM standard compliant ▪▪ Excellent image quality at high image rates ▪▪ Resolutions of 1, 2, 4 or 8 megapixel ▪▪ Frame rates up to 120 fps ▪▪ Compact design (52 x 52 x 72 mm) Camera Type (11047091) www.baumer.com/vision/login open wire Safety Installation Conformity: Installation sample without PoE CE, FCC Part 15 Class B, RoHS Safety instructions UNC 1/4-20 36 26 Notice open wire See User´s Guide for the complete safety instructions! Installation sample with PoE via NIC open wire 1 - PoE network interface card (NIC) 2 - network cable 3 - Process interface cable 16 x M3 depth 6 36 26 ▪▪ Protect the sensor from dirt and moisture. ▪▪ Never open the camera housing. ▪▪ Avoid camera contamination by foreign objects. Environmental requirements: Storage temp. Operating temp. Housing temp. Humidity -10°C ... +70°C +5°C ... +60°C max. +60°C 10 % ... 90 % non condensing Further Information For further information on our products visit www.baumer.com For technical issues, please contact our technical support: [email protected] · Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86 © Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany Technical data has been fully checked, but accuracy of printed matter not guaranteed. Subject to change without notice. Printed in Germany 02/15. v1.4 11054358 52 72 Installation sample with PoE via Injector 1 - network interface card (NIC) 2 - network cable 3 - Injector 4 - network cable 5 - Process interface cable Notice Operation with a single GigE link is possible as well. open wire 5 4 36 26 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructios, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occure in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures: ▪▪ Reorient or relocate the receiving antenna. ▪▪ Increase the separation between the equipment and the receiver. ▪▪ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ▪▪ Consult the dealer or an experienced radio/TV technician for help. open wire 1 - network interface card 2 - network cable 3 - Process interface cable 4 - Power cable 52 FCC – Class B device Dimensions ● SXG-F (F-Mount version) (11047092) General Description LED Signaling 1 Heat Transmission 3 2 Caution Provide adequate dissipation of heat, to ensure that the temperature does not exceed +60°C (+140°F). 4 3 The surface of the camera may be hot during operation and immediately after use. Be careful when handling the camera and avoid contact over a longer period. 1 2 6 Nr. Description T 5 Nr. suggested: Description LED Signal Meaning Link active Receiving 1 (respective) lens mount 4 Digial-IO supply 1 2 Power Supply 5 Data Port 1 2 yellow Transmitting 3 Data Port 0 (PoE) 6 Signaling-LED 3 green qellow Power On Readout active Data Interfaces Power Supply and Process Interface Data / Control 1000 Base-T (Port 0) 8 Data / Control 1000 Base-T (Port 1) LED2 LED1 1 8 Power Supply Digital I/O-Supply M8 / 8 pins LED1 4 3 1 1 (gn/wh) (gn) (og/wh) (bu) (bu/wh) (og) (bn/wh) (bn) MX1+ MX1MX2+ MX3+ MX3MX2MX4+ MX4- 1 2 3 4 5 6 7 8 (gn/wh) (gn) (og/wh) (bu) (bu/wh) (og) (bn/wh) (bn) MX1+ MX1MX2+ MX3+ MX3MX2MX4+ MX4- 1 3 4 (bn) (bu) (bk) Notice Only Port 0 supports Power over Ethernet (38 VDC .. 57 VDC). For the data transfer, the ports are equal. For Single GigE connect one port and for Dual GigE connect the second Port additionally. The order does not matter. 3 2 5 8 6 4 1 2 3 4 5 6 7 8 T dissipation tion, a specific method for proper heat is not defined, but the following principles are green green flash LED2 As there are numerous possibilities for installa- Power VCC GND not used 1 2 3 4 5 6 7 8 (wh) (bn) (gn) (ye) (gr) (pk) (bu) (rd) 7 1 Line 5 Line 1 Line 0 GND Uex Line 3 Line 4 Line 2 Power Supply Power VCC 20 VDC .. 30 VDC ▪▪ Operate the cameras only in mounted condition with a good heat conductor (e.g. aluminum) T: Housing temperature measurement point ▪▪ Mounting in combination with forced convection may provide proper heat dissipation