CBTL08GP053 USB Type-C High performance Crossbar Switch IC Rev. 1 — 18 June 2015 Objective short data sheet 1. General description CBTL08GP053 is an USB Type-C High Performance Crossbar Switch IC meant to be used for Type-C connector interface high speed passive switching applications. It provides switching of high speed differential signals that correspond to various interface standards: USB3.1 (10 Gbps), DP1.3 (8.1 Gbps), PCI Express 3.0 (8 Gbps), etc. It supports switching of single ended signals over Type-C interface. In addition, side band switching of AUX and other dedicated signals for transport over SBU1 and SBU2. It provides the I2C-bus interface for switch control, configuration and status update. It operates from a single platform power supply VDD. This IC is targeted for a wide range of platforms (PCs, Tablets, Convertibles, Smart phones) and PC Accessories (e.g. Docks, Monitors, etc.) applications. CBTL08GP053 is available in a small footprint package option: VFBGA40 4.75 mm 3.25 mm, 0.5 mm pitch. 2. Features and benefits 2.1 High speed switch features Supports the following interface standards: USB3.1, DP1.3, DP++, PCIe 3.0 Supports signaling rates up to 10 Gbps Performs Multiplexing or Switching of High speed differential signals or Single ended signals All switches are direction agnostic Design based on both Patented and Patent pending High performance Switch technology Target performance specification Differential signaling (peak to peak) of 1.4 V and common mode level over 0 V to 2.2 V 1.8 V single ended rail to rail signaling Ron: 7 (typ) Insertion loss: 1.2 dB at 2.7 GHz, 1.8 dB at 5.4 GHz, 3dB at 8.5 GHz (typ) Isolation: 23 dB at 2.7 GHz, 16.5 dB at 5.4 GHz (typ) Cross talk: 32 dB at 2.7 GHz, 24 dB at 5.4 GHz (typ) Return loss: 20 dB at 2.7 GHz, 16 dB at 5.4 GHz (typ) Very low intra pair skew Very low propagation delay (80 ps typical) and inter pair skew (35 ps typical) CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC Switch paths selectable through the I2C-bus interface (registers for atomic and sequential switch selection) 2.2 Sideband auxiliary crossbar switch features Single ended 2:1 multiplexing/switching with single ended cross bar switching of both differential AUX or single ended UART or I2C or miscellaneous signals Switches are direction agnostic Switches are 5.5 V tolerant Target performance specification (typical values) Ron 8 (typ) at Vcm = 0.5 V to 2.65 V Very low intra pair skew Very low propagation delay (80 ps typical) Switch paths selectable through the I2C-bus interface (registers for atomic and sequential switch selection) 2.3 General Supports I2C slave interface Standard mode (100 kbit/s) and Fast mode (400 kbit/s) I2C Slave address programmable up to 4 values Back current protection on Control pins and exposed connector side I/O pins Single 3.3V power supply Current consumption Active mode (all switches are functional): 300 A (typ) Standby mode (all switches in Hi-Z): 15 A (max) Operating temperature: 40 to 105 C ESD 2 kV HBM, 500 V CDM Package: VFBGA40 4.75 mm 3.25 mm, 0.5 mm pitch 3. Applications PC platforms: Notebook PCs, Desktop PCs, Ultrabooks Tablets, 2:1 Convertibles, Smartphones and Portable devices PC accessories/peripherals: Multi-Function Monitors, etc. CBTL08GP053_SDS Objective short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 18 June 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 2 of 8 CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC 4. Ordering information Table 1. Ordering information Type number CBTL08GP053[1] [1] Topside marking Package Name Description Version GP053 VFBGA plastic, very fine-pitch ball grid array package; body 4.75 mm 3.25 mm 0.92 mm; 0.5 mm pitch SOT1439-1 Total height after printed-circuit board mounting 1 mm (maximum) 4.1 Ordering options Table 2. Ordering options Type number Orderable part number Package Packing method CBTL08GP053 CBTL08GP053 VFBGA Reel 7" Q2/T3 500 *standard mark SMD Tamb = 40 C to +85 C CBTL08GP053 CBTL08GP053 VFBGA Reel 13" Q2/T3 5000 *standard mark SMD Tamb = 40 C to +85 C CBTL08GP053_SDS Objective short data sheet Minimum order quantity All information provided in this document is subject to legal disclaimers. Rev. 1 — 18 June 2015 Temperature © NXP Semiconductors N.V. 2015. All rights reserved. 3 of 8 CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC 5. Block diagram IP1+/MUX IP2+/- OP1+/- IP3+/MUX OP2+/IP4+/- MUX OP3+/- IP5+/- IP6+/- MUX OP4+/- 2:1 IP7A/7B OP5A/5B IP8A/8B I2C_CLK I2C_SDA SLV_ADDR1 SLV_ADDR2 MANAGEMENT AND CONTROL SW_EN Fig 1. CBTL08GP053_SDS Objective short data sheet VDD VDDIO GND aaa-016670 CBTL08GP053 functional block diagram All information provided in this document is subject to legal disclaimers. Rev. 1 — 18 June 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 4 of 8 CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC 6. Revision history Table 3. Revision history Document ID Release date Data sheet status Change notice Supersedes CBTL08GP053_SDS v.1 20150618 Objective short data sheet - - CBTL08GP053_SDS Objective short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 18 June 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 5 of 8 CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC 7. Legal information 7.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 7.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 7.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. CBTL08GP053_SDS Objective short data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 1 — 18 June 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 6 of 8 CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 7.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 8. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] CBTL08GP053_SDS Objective short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 18 June 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 7 of 8 CBTL08GP053 NXP Semiconductors USB Type-C High performance Crossbar Switch IC 9. Contents 1 2 2.1 2.2 2.3 3 4 4.1 5 6 7 7.1 7.2 7.3 7.4 8 9 General description . . . . . . . . . . . . . . . . . . . . . . Features and benefits . . . . . . . . . . . . . . . . . . . . High speed switch features . . . . . . . . . . . . . . . Sideband auxiliary crossbar switch features. . . General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering information . . . . . . . . . . . . . . . . . . . . . Ordering options . . . . . . . . . . . . . . . . . . . . . . . . Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . . . Legal information. . . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information. . . . . . . . . . . . . . . . . . . . . . Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 2 2 2 3 3 4 5 6 6 6 6 7 7 8 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2015. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 18 June 2015 Document identifier: CBTL08GP053_SDS